Stefano Babic [Fri, 23 Nov 2012 05:19:24 +0000 (05:19 +0000)]
OMAP3: fix panel timing on the mt_ventoux board
Signed-off-by: Stefano Babic <sbabic@denx.de>
Davide Bonfanti [Wed, 21 Nov 2012 00:45:12 +0000 (00:45 +0000)]
davinci: fixed cpu reset
The reset procedure works on watchdog timer while before it was modifying
TIMER_1 registers.
Tested on DM365.
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
ajoy [Sat, 17 Nov 2012 21:10:15 +0000 (21:10 +0000)]
OMAP3 SPI : Fixed bugs related to SPI transfer
Added posted writes (read after writes) to effect the
change immediately for channel confiuration and channel
enable register
Disable the channel to purge receieve data in TX_ONLY
mode transfer otherwise rx data will get affected by
the next immediate RX_ONLY mode transfer
Wait for the EOT bit to be set after last byte has been
loaded to TX shift register in the the TX_ONLY mode.This
ensures TX data has been completely shifted out
Disable the channel in RX_ONLY mode before reading the
last data from RXX register to prevent the SPI slave
to transmit next word
Signed-off-by: Ajoy Kumar Das <akdas75@yahoo.in>
Cc: Tom Rini <trini@ti.com>
Cc: jacopo mondi <j.mondi@voltaelectronics.com>
Lokesh Vutla [Thu, 15 Nov 2012 21:06:33 +0000 (21:06 +0000)]
omap: emif: configure emif only when required
DMM_LISA_MAP registers program whether memory is mapped
on particular EMIF or not. Irrespective of these registers
EMIF is getting configured. Correcting the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Robert P. J. Day [Thu, 15 Nov 2012 01:21:18 +0000 (01:21 +0000)]
OMAP: Tweak omap-common/Makefile since reset.S -> reset.c
Git commit
d417d1db5f9092d125ddea882ced77eaa5f3d236 replaced the
omap-common file reset.S with reset.c, but the Makefile was not
adjusted for that.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Robert P. J. Day [Tue, 13 Nov 2012 08:12:08 +0000 (08:12 +0000)]
omap4: Add comments on some "#endif"s for readability.
No functional changes, simply for readability.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Robert P. J. Day [Tue, 13 Nov 2012 07:57:54 +0000 (07:57 +0000)]
omap3: Add a few comments to "#endif"s for readability.
No functional changes, just more comments for readability when a
preprocessor check spans more than a few lines, and for consistency.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Peter Barada [Tue, 13 Nov 2012 07:40:28 +0000 (07:40 +0000)]
Pass sdrc timing values through board_sdrc_timings structure
Instead of passing individual registers by value to board_get_mem_timings,
pass a board_mem_timings structure pointer for the board files to fill in.
Pass same structure pointer to write_sdrc_timings. This saves about
90 bytes of space in SPL.
Signed-off-by: Peter Barada <peter.barada@logicpd.com>
Robert P. J. Day [Sun, 11 Nov 2012 23:20:58 +0000 (23:20 +0000)]
omap3_beagle.h: Fix comment for true/false return value.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Ilya Yanok [Tue, 6 Nov 2012 13:06:35 +0000 (13:06 +0000)]
am335x_evm: enable SPL NAND support
Enable booting from NAND support from AM335x boards as well as
environment in NAND.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:06:34 +0000 (13:06 +0000)]
am33xx_spl_bch: simple SPL nand loader for AM33XX
AM33XX with BCH8 can't work with nand_spl_simple correctly
because custom read_page implementation is required for proper
syndrome generation.
This simple driver mostly duplicates nand_spl_simple but has
nand_read_page changed to suit our needs.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Mansoor Ahamed [Tue, 6 Nov 2012 13:06:33 +0000 (13:06 +0000)]
omap_gpmc: BCH8 support (ELM based)
This patch adds support for BCH8 error correction code to omap_gpmc
driver. We use GPMC to generate codes/syndromes but we need ELM to find
error locations from given syndrome.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
[ilya: merge it with omap_gpmc driver, some fixes and cleanup]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Mansoor Ahamed [Tue, 6 Nov 2012 13:06:32 +0000 (13:06 +0000)]
am33xx: add ELM support
AM33XX has Error Location Module (ELM) that can be used in conjuction
with GPMC controller to implement BCH codes fully in hardware.
This code is mostly taken from arago tree.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:06:31 +0000 (13:06 +0000)]
am335x_evm: enable NAND support
Enable NAND support for AM335X boards.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:06:30 +0000 (13:06 +0000)]
am33xx: NAND support
TI AM33XX has the same GPMC controller as OMAP3 so we could just use the
existing omap_gpmc driver. This patch adds adds required
definitions/intialization.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:06:29 +0000 (13:06 +0000)]
am335x_evm: add nand pinmux definition
Add NAND pins mux settings for AM335X devices. Enable NAND pins
for AM335X EVM board.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:06:28 +0000 (13:06 +0000)]
OMAP: include sys_proto.h from boot-common
Include asm/arch/sys_proto.h for gpmc_init prototype.
Without this we get a warning while building for AM335x.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Andreas Bießmann [Fri, 2 Nov 2012 00:14:57 +0000 (00:14 +0000)]
omap3/mem.c: remove unused defines
These GPMC_CS defines are a leftover from prior gpmc_init(). Commit
187af954
removed the need for these definitions but missed to remove them.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Albert ARIBAUD [Sun, 25 Nov 2012 12:01:58 +0000 (13:01 +0100)]
Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'
Marek Vasut [Wed, 21 Nov 2012 17:02:59 +0000 (17:02 +0000)]
mx28: Fix typo in POWER_DCLIMITS_NEGLIMIT_OFFSET
The POWER_DCLIMITS_NEGLIMIT_OFFSET bit in mx28 power supply block is
not called POWER_DCLIMITS_NETLIMIT_OFFSET, but POWER_DCLIMITS_NEGLIMIT_OFFSET.
Correct the name in the header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Wed, 21 Nov 2012 16:50:39 +0000 (16:50 +0000)]
mx28: Fix typo in POWER_MINPWR_VBG_OFF
The POWER_MINPWR_VBG_OFF bit in mx28 power supply block is not called
POWER_MINPWR_FBG_OFF, but POWER_MINPWR_VBG_OFF. Correct the name in the
header file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Stephen Warren [Mon, 5 Nov 2012 13:22:00 +0000 (13:22 +0000)]
tegra: use generic fs commands in BOOTCOMMAND
Modify tegra-common-post.h's BOOTCOMMAND definition to use the generic
filesystem command load rather than separate fatload and ext2load.
This removes the need to iterate over supported filesystem types in the
boot command.
This requires editing all board config headers to enable the new
commands. The now-unused commands are left enabled to assue backwards
compatibility with any user scripts. Boards (all from Avionic Design)
which define custom BOOTCOMMAND values are not affected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
tegra generic fs cmds fixup
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Mon, 5 Nov 2012 13:21:01 +0000 (13:21 +0000)]
tegra: config: seaboard: Move tegra-common-post to correct place
The NAND defines ended up before this include file, but should be after
it, so it doesn't become a post-pre-NAND.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Mon, 5 Nov 2012 13:21:00 +0000 (13:21 +0000)]
tegra: Remove unnecessary CONFIG_SYS_NAND_BASE
Now that we are using the new CONFIG_SYS_NAND_SELF_INIT setup, we don't
need CONFIG_SYS_NAND_BASE. Punt it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 2 Nov 2012 06:56:13 +0000 (06:56 +0000)]
ARM: tegra: enable 8-bit SD slots in board files
Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.
Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.
Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.
Whistler was already registering its ports as 8-bit.
TrimSlice doesn't have any 8-bit ports.
I don't have any Avionic Design boards nor the Colibri board to test with.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 2 Nov 2012 06:56:12 +0000 (06:56 +0000)]
mmc: tegra: support 4-bit operation too on 8-bit slots
If a board has all 8 data lines routed, the SD/MMC controller can still
operate in 4-bit (or presumably even 1-bit) mode. Adjust Tegra's MMC
driver to report the 4-bit capability even for 8-bit slots.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Allen Martin [Thu, 1 Nov 2012 13:41:16 +0000 (13:41 +0000)]
tegra: add CONSOLE_MUX support to tegra-kbc
Add support for CONSOLE_MUX to tegra-kbc driver. This requires
adding a flag to struct keyb to know the driver has already been
initialized so if we try to initialize it again we can just return
success. Also call into iomux_doenv() from drv_keyboard_init to
re-evaluate the stdin string.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Thu, 1 Nov 2012 12:14:37 +0000 (12:14 +0000)]
ARM: tegra: TrimSlice: add support for USB1 port
TrimSlice's USB1 port has two purposes; it either acts as a device port
hosting Tegra's USB recovery protocol, or acts as a host port connected
to the internal USB->SATA bridge chip, which may in turn be connected to
an SSD or HDD. Add the appropriate device tree and board configuration
options to enable this port as a host port, and route the port to the
SATA bridge using the VBUS GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Mayuresh Kulkarni [Wed, 17 Oct 2012 13:25:00 +0000 (13:25 +0000)]
tegra: Enable display/lcd support on Seaboard
Enable the Seaboard's 16-bit LCD and use it as the console.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:59 +0000 (13:24 +0000)]
lcd: Add CONFIG_CONSOLE_SCROLL_LINES option to speed console
When the cursor position gets to the end of the LCD console we normally
scroll by one line. This adds an option to increase that value.
Console scrolling is often slow, and if a large amount of output is
being sent, increasing this option to 10 or so will speed things up
considerably.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:58 +0000 (13:24 +0000)]
tegra: fdt: Add LCD definitions for Seaboard
The Seaboard has a 1366x768 16bpp LCD. The backlight is controlled
by one of the PWMs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:57 +0000 (13:24 +0000)]
tegra: Support control of cache settings for LCD
Add support for selecting the required cache mode for the LCD:
off, write-through or write-back.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:56 +0000 (13:24 +0000)]
tegra: Align LCD frame buffer to section boundary
For tegra we want to enable the cache for the LCD. This is easier if
we can avoid using L2 page tages, so align the LCD to a section
boundary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Tue, 30 Oct 2012 13:40:18 +0000 (13:40 +0000)]
lcd: Add support for flushing LCD fb from dcache after update
This provides an option for the LCD to flush the dcache after each update
(puts, scroll or clear).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:54 +0000 (13:24 +0000)]
lcd: Add CONFIG_LCD_ALIGNMENT to select frame buffer alignment
The normal alignment is PAGE_SIZE, but if this is defined, we can support
other alignments.
The motivation for this change is to make the display section-aligned on
ARM so that we can easily turn off data caching for the frame buffer region
without resorting to level 2 page tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:53 +0000 (13:24 +0000)]
arm: Add control over cachability of memory regions
Add support for adjusting the L1 cache behavior by updating the MMU
configuration. The mmu_set_region_dcache_behaviour() function allows
drivers to make these changes after the MMU is set up.
It is implemented only for ARMv7 at present.
This is needed for LCD support, where we want to make the LCD frame buffer
write-through (or off) rather than write-back.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:52 +0000 (13:24 +0000)]
tegra: Add LCD support to Nvidia boards
Add calls to the LCD driver from Nvidia board code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:51 +0000 (13:24 +0000)]
tegra: Add LCD driver
This driver supports driving a single LCD and providing a U-Boot console
on it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Wei Ni [Wed, 17 Oct 2012 13:24:50 +0000 (13:24 +0000)]
tegra: Add SOC support for display/lcd
Add support for the LCD peripheral at the Tegra2 SOC level. A separate
LCD driver will use this functionality to configure the display.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@nvidia.com>
Mayuresh Kulkarni:
- changes to remove bitfields and clean up for submission
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass:
- simplify code, move clock control into here, clean-up
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:49 +0000 (13:24 +0000)]
tegra: Add support for PWM
The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:48 +0000 (13:24 +0000)]
tegra: fdt: Add LCD definitions for Tegra
Add LCD definitions and also a proposed binding for LCD displays.
The PWM is as per what will likely be committed to linux-next soon.
The displaymode binding comes from a proposal here:
http://lists.freedesktop.org/archives/dri-devel/2012-July/024875.html
The panel binding is new, and fills a need to specify the panel
timings and other tegra-specific information. Should a binding appear
that allows the pwm to handle this automatically, we can revisit
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:47 +0000 (13:24 +0000)]
tegra: fdt: Add pwm binding and node
This binding will apparently soon be in linux-next. Bring it in now
since we need to do something, and may as well try to target what
Linux will have.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:46 +0000 (13:24 +0000)]
tegra: Add display support to funcmux
Add support for a default pin mapping for display1.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Wed, 17 Oct 2012 13:24:45 +0000 (13:24 +0000)]
tegra: Use const for pinmux_config_pingroup/table()
These two functions don't actually modify their arguments so add a const
keyword.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Tue, 30 Oct 2012 13:38:53 +0000 (13:38 +0000)]
pxa: Disable dcache on palmld, palmtc, zipitz2
These platforms don't include dcache support. Define CONFIG_SYS_DCACHE_OFF
so that functions don't try to call non-existent routines like
flush_dcache_range().
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Benoît Thébaudeau [Mon, 5 Nov 2012 10:07:04 +0000 (10:07 +0000)]
mx5: Mark lowlevel_init board-specific code
The mx5 lowlevel_init.S contains board-specific code based on the reference
design. Let's keep it since it avoids creating new lowlevel_init files and it
may be used by many boards. But add a config to make it optional in order not to
cause issues on boards not following this part of the reference design.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Fri, 16 Nov 2012 06:46:24 +0000 (06:46 +0000)]
ehci-mxc: Fix host power mask bit for i.MX25
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Eric Bénard <eric@eukrea.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Fabio Estevam [Fri, 16 Nov 2012 05:09:10 +0000 (05:09 +0000)]
mx35pdk: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:09 +0000 (05:09 +0000)]
mx31pdk: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:08 +0000 (05:09 +0000)]
mx25pdk: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:07 +0000 (05:09 +0000)]
mx51evk: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:06 +0000 (05:09 +0000)]
mx6qsabre_common: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:05 +0000 (05:09 +0000)]
mx6qsabrelite: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:04 +0000 (05:09 +0000)]
mx53loco: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 16 Nov 2012 05:09:03 +0000 (05:09 +0000)]
mx28evk: Configure CONFIG_BOOTDELAY to one second
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Benoît Thébaudeau [Fri, 16 Nov 2012 01:42:49 +0000 (01:42 +0000)]
ehci-mxc: Fix host power mask bit for i.MX35
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Michael Burkey <mdburkey@gmail.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Fri, 16 Nov 2012 01:30:10 +0000 (01:30 +0000)]
mx6: clock: Only show CSPI clock if CSPI is enabled
If a board does not enable CSPI, there is no need to show the CSPI clock
frequency as part of the 'clock' command.
Reported-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Dirk Behme <dirk.behme@gmail.com>
Fabio Estevam [Thu, 15 Nov 2012 11:23:24 +0000 (11:23 +0000)]
spi: mxc_spi: Fix spi clock glitch durant reset
Measuring the spi clock line on a scope shows a 'glitch' during the reset of the
spi.
Fix this by toggling only the MXC_CSPICTRL_EN bit, so that the clock line becomes
always stable.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Thu, 15 Nov 2012 11:23:23 +0000 (11:23 +0000)]
spi: mxc_spi: Fix handling of chip select
In decode_cs() function the polarity of the chip select must be taken into
account.
Also, for the case of low active chip select, the CS was activated too early.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Thu, 15 Nov 2012 11:23:22 +0000 (11:23 +0000)]
mx5: Print CSPI clock in 'clock' command
Print CSPI clock in 'clock' command.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 15 Nov 2012 11:23:21 +0000 (11:23 +0000)]
mx5: Align SPI CS naming with i.MX53 reference manual
Align SPI chip select naming with i.MX53 reference manual.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:58:35 +0000 (09:58 +0000)]
ehci-mx5/6: Make board_ehci_hcd_init() optional
A custom board_ehci_hcd_init() may be unneeded, so add a weak default
implementation doing nothing.
By the way, use simple __weak from linux/compiler.h for
board_ehci_hcd_postinit() instead of weak alias with full attribute.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:58:25 +0000 (09:58 +0000)]
mx35pdk: Add support for OTG
Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:58:12 +0000 (09:58 +0000)]
ehci-mxc: Add support for i.MX35
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:57:59 +0000 (09:57 +0000)]
ehci-mxc: Define host offsets
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare
to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at
SoC level.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:57:48 +0000 (09:57 +0000)]
ehci-mxc: Make i.MX25 EHCI configurable
Use EHCI MXC configuration options for i.MX25.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matthias Weisser <weisserm@arcor.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:57:27 +0000 (09:57 +0000)]
ehci-mxc: Make EHCI power/oc polarities configurable
Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:57:14 +0000 (09:57 +0000)]
ehci-mx5: Add missing OC_DIS for i.MX53
The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:56:59 +0000 (09:56 +0000)]
ehci-mx5: Fix *PM usage for i.MX53
The MXC_*_UCTRL_*PM_BIT bits are available only on i.MX51.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:56:44 +0000 (09:56 +0000)]
ehci-mx5: Fix OPM usage
MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like
MXC_H1_UCTRL_H1PM_BIT and MXC_H2_UCTRL_H2PM_BIT, not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:56:30 +0000 (09:56 +0000)]
ehci-mx5: Fix OC_DIS usage
MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like MXC_H1_OC_DIS_BIT,
not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:56:15 +0000 (09:56 +0000)]
ehci-mx5: Clean up
Clean up ehci-mx5:
- Fix column alignments.
- Fix comments.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:55:57 +0000 (09:55 +0000)]
ehci-mxc: Clean up
Clean up ehci-mxc:
- Remove useless #if's.
- Fix identation.
- Issue a #error if used with an unsupported platform.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Benoît Thébaudeau [Tue, 13 Nov 2012 09:55:30 +0000 (09:55 +0000)]
mx31: Move EHCI definitions to ehci-fsl.h
The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to
ehci-fsl.h so that all MXC SoCs can use them.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Rajeshwari Shinde [Fri, 2 Nov 2012 01:15:38 +0000 (01:15 +0000)]
EXYNOS5: Enable SPI booting.
This patch enables SPI Booting for EXYNOS5
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Fri, 2 Nov 2012 01:15:37 +0000 (01:15 +0000)]
EXYNOS5: Enable SPI
This patch enables SPI driver for EXYNOS5.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Fri, 2 Nov 2012 01:15:36 +0000 (01:15 +0000)]
SPI: Add SPI Driver for EXYNOS.
This patch adds SPI driver for EXYNOS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: jy0922.shim@samsung.com
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Fri, 2 Nov 2012 01:15:35 +0000 (01:15 +0000)]
EXYNOS5: Add base address for SPI
Add base address definition for SPI device on Exynos.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Hatim RV [Fri, 2 Nov 2012 01:15:34 +0000 (01:15 +0000)]
EXYNOS: Add clock for SPI
Add api to calculate and set the clock for SPI channels
Signed-off-by: James Miller <jamesmiller@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Sun, 28 Oct 2012 19:32:54 +0000 (19:32 +0000)]
EXYNOS5: Add pinmux support for SPI
This patch adds pinmux support for SPI channels
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:30 +0000 (19:49 +0000)]
SMDK5250: Enable Sound
This patch enables sound support for EXYNOS5
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:29 +0000 (19:49 +0000)]
EXYNOS: Add clock for I2S
This patch adds clock support for I2S
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:28 +0000 (19:49 +0000)]
EXYNOS: Add I2S base address
This patch adds base address for I2S
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:27 +0000 (19:49 +0000)]
EXYNOS: Add pinmux for I2S
This patch adds pinmux support for I2S1
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:26 +0000 (19:49 +0000)]
EXYNOS: Add parameters required by I2S
This patch adds the audio parameters required by the I2S to play the
predefined audio data.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:25 +0000 (19:49 +0000)]
EXYNOS: Add I2S registers
This patch add I2S registers
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:24 +0000 (19:49 +0000)]
Sound: Add command for audio playback
This patch adds command to test audio playback.
sound init - Initialises the audio subsystem (i2s and wm8994 codec)
sound play - Plays predefined the audio data when specified length
and frequency.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:23 +0000 (19:49 +0000)]
SOUND: Add WM8994 codec
This patch adds driver for audio codec WM8994
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Thu, 25 Oct 2012 19:49:22 +0000 (19:49 +0000)]
SOUND: SAMSUNG: Add I2S driver
This patch adds driver for I2S interface specific to samsung.
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 19 Oct 2012 05:34:07 +0000 (05:34 +0000)]
exynos4: universal_C210: add display support
This patch add support for display on Universal C210 board.
Width of displyed logo must be not bigger than 480 pixel and
is limited by width of the screen.
Tizen logo size is 520x120 pixels and should be resized.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 19 Oct 2012 05:34:06 +0000 (05:34 +0000)]
drivers: video: fix image position
This patch fixes image position on screen when images's height or width is biger then the lcd's.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 19 Oct 2012 05:34:05 +0000 (05:34 +0000)]
drivers: video: Add ld9040 video driver
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 19 Oct 2012 05:34:04 +0000 (05:34 +0000)]
misc:max8998 Add LDO macros
Add LDO7 and LDO17 macros to max8998_pmic.h necessary to power on the LCD.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Fri, 19 Oct 2012 05:34:03 +0000 (05:34 +0000)]
exynos4: universal_C210: use software SPI
This patch use software spi on Samsung Universal C210 board.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Minkyu Kang [Thu, 25 Oct 2012 22:15:33 +0000 (22:15 +0000)]
s3c64xx: fix the compiler error and warning
This patch is fixing the following errors
s3c64xx.c:175: error: variable 's3c64xx_serial_drv' has initializer but incomplete type
s3c64xx.c:176: error: unknown field 'name' specified in initializer
s3c64xx.c:176: warning: excess elements in struct initializer
s3c64xx.c:176: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:177: error: unknown field 'start' specified in initializer
s3c64xx.c:177: warning: excess elements in struct initializer
s3c64xx.c:177: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:178: error: unknown field 'stop' specified in initializer
s3c64xx.c:178: warning: excess elements in struct initializer
s3c64xx.c:178: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:179: error: unknown field 'setbrg' specified in initializer
s3c64xx.c:179: warning: excess elements in struct initializer
s3c64xx.c:179: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:180: error: unknown field 'putc' specified in initializer
s3c64xx.c:180: warning: excess elements in struct initializer
s3c64xx.c:180: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:181: error: unknown field 'puts' specified in initializer
s3c64xx.c:181: warning: excess elements in struct initializer
s3c64xx.c:181: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:182: error: unknown field 'getc' specified in initializer
s3c64xx.c:182: warning: excess elements in struct initializer
s3c64xx.c:182: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:183: error: unknown field 'tstc' specified in initializer
s3c64xx.c:183: warning: excess elements in struct initializer
s3c64xx.c:183: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c: In function 's3c64xx_serial_initialize':
s3c64xx.c:188: warning: implicit declaration of function 'serial_register'
s3c64xx.c: At top level:
s3c64xx.c:191: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'struct'
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Ashok Kumar Reddy [Wed, 26 Sep 2012 18:14:59 +0000 (23:44 +0530)]
ARM: arm1176: Define arch_cpu_init() for s3c64xx
arch_cpu_init() is removed from cpu level to SOC level for arm1176
in commit 4ea6d6b,the same is done for s3c64xx
Signed-off-by: Ashok Kumar Reddy <ashokkourla2000@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Fri, 24 Aug 2012 00:39:24 +0000 (00:39 +0000)]
SMDK5250: Config: Enable MAX77686 pmic chip
This patch enables MAX77686 pmic chip for SMDK5250.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Fri, 24 Aug 2012 00:39:23 +0000 (00:39 +0000)]
PMIC: MAX77686: Add support for MAX77686
This patch adds driver and register definitions for PMIC chip
MAX77686.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Marek Vasut [Sat, 21 Jul 2012 05:02:24 +0000 (05:02 +0000)]
dm: wdt: Move s5p watchdog timer to drivers/watchdog/
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Minkyu Kang [Mon, 15 Oct 2012 01:58:00 +0000 (01:58 +0000)]
EXYNOS: Clock: Add common function for pll rate calculation
Moved the common code to calculate pll clock rate to new function
exynos_get_pll_clk().
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>