ARM: dtsi: imx6qdl-sabresd: add a fixed regulator for WM8962

On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10,
so add a regulator controled by GPIO_4_10 for WM8962.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dtsi: imx6dl: Add a pinctrl for AUDMUX

Add a pinctrl for AUDMUX used on imx6dl-sabresd.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dtsi: imx6q/imx6dl: Add a pinctrl for I2C1

Add a pinctrl for I2C1 used on imx6q/dl-sabresd.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6qdl-sabresd: add clko1 iomux configuration

Setting GPIO_0 pad as clko1 clock output to provide MCLK for WM8962.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: Phytec imx6q pfla02 and pbab01 support

Add support for imx6q Phytec phyFLEX-i.MX6 Quad (aka pfla02 and pbab01).
 - Module pfla02
 - Carrier-Board pbab01

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6q: Add pinctrl for usdhc2 and enet

Add a group to the usdhc2 and enet pinctrl.

Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore-rdk: Add MTD name for NOR flash

This patch adds name for NOR flash. This keeps compatibility for
commandline partitions parsing from old bootloaders and make name
of device same for DT and non-DT boot.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore-rdk: Add SDHC support

This patch adds the SHDC devicetree node for PCM970 board.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: i.MX27: Add SDHC devicetree nodes

This patch adds the missing SDHC devicetree nodes for i.MX27 SoCs.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: i.MX27: Add DMA devicetree node

This patch adds the missing DMA devicetree node for i.MX27 SoCs.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR

Enable the WEIM NOR for imx6q{dl}-sabreauto boards.

For the pin conflict with SPI NOR, its status is set to "disabled".

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6dl: add pinctrls for WEIM NOR

Add two pinctrls for WEIM:
   one for the weim nor, another for the chipselect.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6q: add pinctrls for WEIM NOR

Add two pinctrls for WEIM:
   one for the weim nor, another for the chipselect.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6qdl: add more information for WEIM

Add the clock and compatible information for the weim.
Also adds the weim label.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM

In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.

In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.

The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

drivers: bus: add a new driver for WEIM

The WEIM(Wireless External Interface Module) works like a bus.
You can attach many different devices on it, such as NOR, onenand.

In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.

This patch also adds the devicetree binding document.
The driver only works when the devicetree is enabled.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: add DI1_CLK to pinctrl for disp1

Add missing pin config

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: fix lvds/disp pinctrl

use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[Steffen: split up patch into tqma53+mba53 part]
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: use reset gpio for FEC

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: add missing gpio stuff for pca9554

Add properties to make use of pca9554 gpio expander.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: add sound support

Enable the sgtl5000 found on MBa53 mainboard.
Also enable audio muxer and ssi, which are needed for sound to work.

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: add Tevision Encoder

Enable tve on MBa53.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: Add display support

As the displays are optional and we have more than one, also
set the status of the parallel display and the ldb to disabled.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: mba53: enable usbotg & usbh1

Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: tqma53: add WP/CD pinctrl and vmmc to esdhc2

Add WP/CD pinctrl for esdhc2.
Also, add vmmc-supply for esdhc2.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: Add TVE entry to i.MX53 dtsi

This adds the Television Encoder (TVEv2) device tree node
to the i.MX53 dtsi.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: tqma53: rev 300 specific pin configuration

I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: tqma53: fix pinctrl settings

BIT(31) is NO_PAD_CTL, not BIT(16)

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: tqma53: Fix interrupt polarity for the mc34708

It's active high, not active low.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore-som: Add initial support for PCM970 RDK

Patch adds initial dts for Phytec PCM970 Rapid development kit.
- Added definition for UART0 and UART1.
- Added additional SPI chipselect which used on RDK for ZegBee module.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore-som: Remove UART definitions

UART1 and UART2 can be unused on some designs with PCM038 module.
Remove these definitions from basic dts and lets choose user only
necessary UARTs in custom designs.
Keep UART0 for using this one as boot console, but since we have
not way to disable usage RTSCTS signals, remove this parameter for UART0.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore: Rename file to match functionality

PCM038 dts can be used as base for development kit board or any
custom PCB designs. Renames this file to match functionality.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx27-phytec-phycore: Add reset GPIO for FEC

FEC (KSZ8001L) reset pin is connected to GPIOC30.
Add this definition to dts.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: add initial VF610 Tower board dts support

Add initial Freescale Vybrid VF610 Tower board support
with uart and fec enabled.

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: add SoC level device tree source for VF610

Add SoC level device tree source for Freescale Vybrid VF610.

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx53: add fec pinctrl

Add a group to the fec pinctrl, for use with MII interface.

Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx53: add ecspi2 pinctrl

Add ecspi2 pinctrl.

Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx53: add cspi pinctrl

Add a group to the cspi pinctrl.

Signed-off-by: Jonas Andersson <jonas@microbit.se>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: mx53qsb: Add support for parallel display

Add support for CLAA WVGA display for i.MX53 QSB.

Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: apf51: add nfc support

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

i.MX6: Documentation: update from fsl,card-wired to non-removable

With the commit 7f217794f (mmc: dt: Consolidate DT bindings),
the device tree properties used by various device drivers
for SD/MMC host controllers were standardized.  One of the changes
was that the property "fsl,card-wired", previously used by the
Freescale driver, was replaced with "non-removable". Fix the example
documentation regarding this.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6qdl: remove redundant ocotp node

There is a redundant ocotp node.  Remove it.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6qdl: remove redundant usbmisc label

There is a redundant label on usbmisc node.  Remove it.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6sl: add initial imx6sl-evk support

Add initial imx6sl-evk board support with uart, usdhc and fec enabled.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: add device tree source for imx6sl SoC

Add SoC level device tree source for imx6sl.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: i.MX6: configure L2 cache data and tag latency

Configure the data and tag latency for the L2 cache. This improves the
system performance.

This configuration is taken from Freescale's kernel patch

"ENGR00153601 [MX6]Adjust L2 cache parameter" [1]

which does

writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL));
writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL));

In this patch we are doing the same via the device tree.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[1] http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/arch/arm/mach-mx6/mm.c?h=imx_3.0.35_12.09.01&id=814656410b40c67a10b25300e51b0477b2bb96d1

ARM: dts: add SPI/NOR for mx6q{dl}-sabreauto boards

Since the SPI/NOR has pin conflict with the WEIM NOR,
we disable the spi/nor by default.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6q: add a gpio for hog

The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6dl: add a gpio for hog

The SPI/NOR needs this gpio for CS.
So add this gpio in the hog pinctrl.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6dl: add a pinctrl for eCSPI1

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: enable the gpmi-nand for imx6q{dl}-sabreauto boards

enable the gpmi-nand for imx6q-sabreauto and imx6qdl-sabreauto boards.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6dl: add pinctrl for gpmi-nand

add the pinctrl item for gpmi-nand.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx6q: remove the unused pins for gpmi-nand

The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and
MX6Q_PAD_NANDF_CS3__NAND_CE3_B.

Just remove them.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: Add SPI support for i.MX27 Phytec PCM038 module

Added SPI node and PMIC MC13783 (spi0.0) to imx27-phytec-phycore DT file.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: Add aliases for i.MX27 SPI controller

Add aliases to determine the proper SPI bus number.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: add Ka-Ro tx53 devicetree

This adds support for the Ka-Ro TX53 System-On-Module.
As a baseboard is needed to operate it, only a *.dtsi and no Makefile entry.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX53: add uart2 pinctrl

Add a group to the uart2 pinctrl.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX53: add uart1 pinctrl

Add a group to the uart1 pinctrl.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX53: add pwm2 pinctrl

Add pinctrl for pwm2.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX53: add ecspi pinctrl

Add a group to the ecspi pinctrl.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX53: add csi pinctrl

Add a group to the csi pinctrl.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX53: add audmux pinctrl

Add a group to the audmux pinctrl.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add support for DENX M53EVK

This patch adds support for the DENX M53EVK board. The board currently supports
NAND, Ethernet, UART, CAN, I2C.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: move imx53-qsb audio codec clk lookup into DT

With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.

Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add PWM1 pinctrl data

This patch adds pinctrl data for PWM1 on MX53.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add LCD IPU pinctrl data

This patch adds pinmux for IPU LCD 1 and IPU LVDS.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add NAND pinctrl data

This patch adds pinctrl data for NAND on MX53.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add I2C2 pinctrl data

This patch adds pinctrl data for different mux of I2C2 on MX53.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add I2C1 pinctrl data

This patch adds pinctrl data for different mux of I2C1 on MX53.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add CAN1 pinctrl data

This patch adds pinctrl data for different mux of CAN1 on MX53.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: mx5: Add AUDMUX4 pinctrl data

This patch adds pinctrl data for the AUDMUX4 on MX53.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: dts: add i2c aliases

This allows to order the i2c character devices correctly,
so that /dev/i2c-0 corresponds to i2c1, /dev/i2c-1 corresponds
to i2c2, and so on. Currently they are ordered by register
address.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx27: Add PWM0 to device tree

Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx: imx53-qsb.dts: enable usbotg and usbh1

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx: use usb-nop-xceiv usbphy entries for imx5x

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx: add imx5x usb clock DT lookups

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: dts: imx: add imx5x usbmisc entries

Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Merge tag 'imx-soc-3.11' into imx/dt

imx soc changes for 3.11:

* New SoCs i.MX6 Sololite and Vybrid VF610 support
* imx5 and imx6 clock fixes and additions
* Update clock driver to use of_clk_init() function
* Refactor restart routine mxc_restart() to get it work for DT boot
  as well
* Clean up mxc specific ulpi access ops
* imx defconfig updates

ARM: imx_v6_v7_defconfig: Enable Vybrid VF610

Let VF610 SoC support be built by default.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx_v6_v7_defconfig: Enable imx-wm8962 by default

Enable imx-wm8962 and PM_RUNTIME, essential for WM8962 CODEC driver.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: clk-imx6qdl: Add clko1 configuration for imx6qdl-sabresd

WM8962 needs 24MHz clock for its MCLK, so choose PLL4 as the parent of clko1.

Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx_v6_v7_defconfig: Enable PWM and backlight options

These options are useful for controlling backlight contrast via PWM.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: Remove mxc specific ulpi access ops

There are ulpi access ops implemented in drivers/usb/phy/phy-ulpi.c.
mxc access ops implement the same access operations within mach-imx. This
patch removes the mxc ulpi file and uses phy-ulpi instead for
imx_otg_ulpi_create.

phy-ulpi successfully tested with i.MX27 Phytec phyCARD-S (pca100).

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: add initial support for VF610

Add initial support for Freescale Vybrid VF610 SoC.

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: add VF610 clock support

Add clock support for Vybrid VF610. It uses dtc macro support to
define all clock IDs in vf610-clock.h to keep clock IDs coherence
between kernel and DT.

Signed-off-by: Jingchang Lu <b35083@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx_v6_v7_defconfig: enable parallel display

Enable paralell display by default

Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: clk: No need to initialize phandle struct

commit 84344b43c (ARM: i.MX5: Allow DT clock providers) introduce the following
sparse warning:

arch/arm/mach-imx/clk.c:12:43: warning: Using plain integer as NULL pointer

There is no need to initialize phandle, so remove it.

Cc: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: irq-common: Include header to avoid sparse warning

Fix the following sparse warning:

arch/arm/mach-imx/irq-common.c:24:5: warning: symbol 'mxc_set_irq_fiq' was not declared. Should it be static?

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: Enable mx6 solo-lite support

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx6: use common of_clk_init() call to initialize clocks

Instead of explicitly calling clock initialization functions, we can
declare the functions with CLK_OF_DECLARE() and then call common
of_clk_init() to have them invoked properly.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx6q: call of_clk_init() to register fixed rate clocks

As the fixed rate clocks are defined in device tree, we can just call
of_clk_init() to register them.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: imx_v6_v7_defconfig: Select CONFIG_DRM_IMX_TVE

Let the mx53 TVE driver be built by default.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: i.MX6: clk: add different DualLite MLB clock config

The CCM_CBCMR register (address 0x02C4018) has different meaning
between the i.MX6 Quad/Dual and the i.MX6 Solo/DualLite.

Compared to the i.MX6 Quad/Dual, the CCM_CBCMR register in the
i.MX6 Solo/DualLite reuses the gpu2d_core bits for the MLB clock
configuration.

Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX5: Add S/PDIF clocks

This patch adds the S/PDIF clocks for i.MX51 and i.MX53. Tested on i.MX53.
The i.MX51 has a second set of spdif_root clock dividers, and on i.MX53
there is an additional input to the spdif_xtal mux.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM i.MX53: Add SATA clock

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx6q: clk: add the eim_slow clock

Add the eim_slow clock, since the weim needs it.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: remove MLB PLL from pllv3

MLB PLL should be handled internally in MLB driver,
so remove it from pllv3.

Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: disable pll8_mlb in mx6q_clks

The MLB PLL clock's operation doesn't fit for clock framework and
it should be handled internally in MLB driver.
Remove initialization of pll8_mlb clock device but leave its
declaration in mx6q_clks to avoid affecting imx6q clock numbering.

Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
CC: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: add initial support for imx6sl

Add initial support for i.MX6 SoloLite.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

ARM: imx: enable low-level debug support for imx6sl

Enable low-level debug support for i.MX6 SoloLite by adding the debug
port definitions for the SoC.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>