mwl8k: recheck if station still has valid rates

We have 6.5 Mbps is minimum rate of the link
as the criterion for creation of BA.

Although we check this before creating the BA
stream, by the time amdpu_action is called from
the workqueue, the link can get affected in the
meantime.
Hence, add an additional check in amdpu_action.

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwl8k: defining interface combinations

AP mode support upto 8 interfaces.
Defining it using iface_combinations

Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: process RX packets in SDIO IRQ thread directly

ksdioirqd has higher priority than kworker. Process RX packets
in SDIO IRQ thread (ksdioirqd/mmcX) directly instead of deferring
the work to kworker to avoid the extra latency.
This improves TCP throughput 15~20% on an ARM platform with SDIO
2.0 controller.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use struct brcmf_if parameter in firmware event callbacks

Firmware events are passed to wl_cfg80211 module associated with
the primary net device. With virtual interface support events can
be received for different interfaces, ie. struct brcmf_if instances.
Pass it in the event to determine appropriate net device associated
with the event.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add dedicated USB log level.

Add USB log level and update and add log messages in usb module.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: on halting driver check before release or free.

brcmf_netdev_stop shall first check bus_if status before bringing
down cfg80211. brcmf_detach shall first check if driver is
allocated.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: check bus state to be data before sending data.

brcmf_netdev_start_xmit and brcmf_fil_cmd_data are checking
bus state for down. These functions should check for data
state.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: return immediately error for out of range key_idx.

when brcmf_cfg80211_del_key was called with out of range key index
then firmware would return error. Checking was added to
brcmf_cfg80211_del_key to immediately return error.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix build regression

This fixes a build regression for x86_64 target that showed up
in 3.7-rc1 due to:

commit 1a87334239757b69eb9885979c32bbf871b3ec88
Author: Hante Meuleman <meuleman@broadcom.com>
Date:   Thu Sep 27 14:17:54 2012 +0200

    brcmfmac: add hostap supoort.

Reported-by: Yuanhan Liu <yuanhan.liu@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: change return type of brcmf_sdio_hdparser

Use int instead of bool as the return type of function
brcmf_sdio_hdparser to explicitly describe error returns.

Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove brcmf_sdbrcm_wait_for_event

brcmf_sdbrcm_wait_for_event is now a one line function and only
used by brcmf_sdbrcm_bus_txctl. Intergrate the function call
wait_event_interruptible_timeout into brcmf_sdbrcm_bus_txctl.

Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: protect consecutive SDIO access with sdio_claim_host

Semaphore sdsem is used to protect consecutive memory access
through SDIO bus. Same functionality is provided by sdio_claim_host/
sdio_release_host interface as well. Replace sdsem with
sdio_claim_host.

Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: decrease the range of SDIO access lock

Semaphore sdsem which protects consecutive SDIO bus access is used
to lock down unnecessary wide range. Decrease the locking range
provides the capability of parallel processing.

Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use dynamically allocated control frame buffer

Rxbuf in SDIO interface is used in normal frame and control frame
read. Use dynamically allocated buffer in control frame read path
for post processing to avoid conflicts.

Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix NULL pointer access in brcmf_create_iovar()

The function brcmf_fil_bsscfg_data_get() calls brcmf_create_iovar()
with data pointer set to NULL, which caused a NULL pointer access.
As it should be possible to provide data in message towards the
firmware, it should just pass the data buffer instead.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove obsolete function brcmf_c_mkiovar

the refactored firmware interface layer made this function obsolete.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove obsolete variable from brcmf_cfg80211_start_ap()

The function brcmf_cfg80211_start_ap() had some variables declared
that were not used or not needed any longer. This patch removes
those variables.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: change parameter of brcmf_set_management_ie()

The function brcmf_set_management_ie() operates on virtual
interface data and brcmf_cfg80211_vif structure provides
all information needed for interfacing with firmware. As
this function will also be needed for interface without
an associated net device it makes sense to provide the vif
instead of deriving it from the net device.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: fix pkt_filter sizeof calculation.

sizeof calculation in setting pkt_filter was incorrect. This
patch fixes that and removes related defines which have become
obsolete.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use wait_event_timeout for 8021x pending count

brcmf_netdev_wait_pend8021x was polling to see if 8021x data was
already sent. Code was replaced using wait_event_timeout.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: handle exceptions in brcmf_bus_start correct.

On exception during brcmf_bus_start the netdev should be freed,
if already allocated.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use fwil for netdev callbacks.

Change setting up multicast, mac address and offloading to use the
refactored firmware interface layer. Remove obsolete brcmf_proto_dcmd
function.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove obsolete i-scan and clean up related code.

e-scan has become the default scanning method. This patch removes
the i-scan related code and cleans up e-scan related code to be
always enabled.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: make pointer type constant in brcmf_set_management_ie()

The vendor ie buffer passed to brcmf_set_management_ie() is not modified
and the caller always provided a constant buffer, which needed a cast.
Better making the buffer parameter of the function constant so the
casts can be removed.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: restrict error condition in brcmf_inform_bss()

The function brcmf_inform_bss() validates the version received
from the device, before processing the individual bss entries.
This error condition is only applicable when the list contains
entries. A specific scan, ie. for a specific ssid, can result
in a scan completion without finding any bss entries. No need
to flag it as an error in the log when this happens.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: simplify if-else condition in brcmf_cfg80211_escan()

Code flow was:
err = foo();
if (!err)
return err;
else
goto exit;
return 0;

Changed it to just to exit label if err is non-zero.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove obsolete structure ap_info

The data stored in ap_info structure is no longer used so remove
it from the driver.

Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar5523: Don't dereference sta if NULL

A missing else caused a potential NULL dereference.

Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar5523: Fix sparse endianness warnings

__be32 variables where used a little careless leading to sparse warnings.
Treat them a little more gentle.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath/ath6kl/hif.c: drop if around WARN_ON

Just use WARN_ON rather than an if containing only WARN_ON(1).

A simplified version of the semantic patch that makes this transformation
is as follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
expression e;
@@
- if (e) WARN_ON(1);
+ WARN_ON(e);
// </smpl>

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Wireless: rt2x00: Add device id for Sweex LW323 to rt2800usb.c

This patch adds detection for the Sweex LW323 USB wireless network card
in the rt2x00 driver (just one line in rt2800usb.c).
It applies to linux-3.7-rc3.

Signed-off-by: Jaume Delclòs <jaume@delclos.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add multi-queue support

This patch adds support for multiple TX queues inside mwifiex
driver. Four different queues according to WMM access categories
are defined for each virtual interface. When a packet is
received from netdev for transmission, tx pending count for
particular queue is incremented and if tx pending count has
reached upper water-mark, this queue is stopped instead of
stopping all queues. Similarly when a packet is successfully
transmitted from device, tx pending count is decremented per
queue and if pending count falls below lower water-mark, queue
operations are again resumed. This ensures that not all
tranmission is blocked if traffic with particular TOS value
suddenly increases.

Also wake all queues after association/IBSS_join/uAP_BSS_start
to enable traffic on all queues.

Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mwifiex: add support for SDIO card reset

When command timeout happens due to a bug in firmware/hardware,
the timeout handler just prints some debug information. User is
unable to reload the driver in this case.

Inspired by 9a821f5 "libertas: add sd8686 reset_card support",
this patch adds card reset support for SDIO interface when
command timeout happens. If the SDIO host contoller supports
MMC_POWER_OFF|UP|ON operations, the chip will be reset and the
firmware will be re-downloaded.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove duplicated include from dhd_dbg.c

Remove duplicated include.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar5523: use module_usb_driver to simplify the code

Use the module_usb_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.

dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

add Marvell 88W8688 support to libertas_sdio

This chip is for example used in the GuruPlug.
This patch avoids the following error:
libertas_sdio: failed to load firmware
libertas_sdio: probe of mmc0:0001:1 failed with error -5

The fix is based on code in:
drivers/net/wireless/libertas_uap/uap_sdio_mmc.c

This file can for example be found on the following links:
http://www.xilka.com/sheeva/2.6/2.6.36/2.6.36.2/source/0002-Driver-for-Marvell-Libertas-8688-SDIO-micro-AP-suppo-2.6.35.patch
http://www.downloadsnewit.co.uk/kernel-v3.0.7/

I followed the following wiki to setup a working WiFi client mode
connection on the GuruPlug:
http://wiki.debian.org/libertas

Signed-off-by: Harro Haan <hrhaan@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: kill MODULE_VERSION

This is pretty pointless. Lets kill this to stop people from
thinking that its actually used. Maybe we should go on
a crusade and kill this completely from the kernel.

Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix memory leak in DFS pattern detector

Free instance of pattern detector if requested DFS domain is
not supported.

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: resolve name collision in DFS detector

set_domain() is already defined in /arch/arm/asm/domain.h

Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: Convert dev_printk(KERN_<LEVEL> to dev_<level>(

dev_<level> calls take less code than dev_printk(KERN_<LEVEL>
and reducing object size is good.
Coalesce formats for easier grep.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192ce: rtl8192cu: rtl8192se: rtl81723ae: Turn on building of the new driver

This patch completes the addition of the new driver for the Realtek
RTL8723AE devices by adding the make file and by modifying Kconfig
and Makefile of rtlwifi. Some variable names were shortened to ease
the problem of limiting all lines to 80 characters, thus changes were
made to wifi.h and rtl8192{ce,cu,sw}/hw.c.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Modify files for addition of rtl8723ae

This patch modifies the files of rtlwifi for the addition of a new driver
to handle the Realtek RTL8723AE wireless device, and introduces a new
routine to maintaim statistics that will be used later for roaming.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8723ae: Add new driver

This patch is the addition of files for a new driver to handle
the Realtek RTL8723AE wireless device.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth-next

Bluetooth: Fix parameter order of hci_get_route

The actual parameter order of hci_get_route is (dst, src) and not (src,
dst). All current callers use the right order but the header file shows
the parameters in the wrong order.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Rename ctrl_id to remote_amp_id

Since we have started to use local_amp_id for local AMP
Controller Id it makes sense to rename ctrl_id to remote_amp_id
since it represents remote AMP controller Id.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Process Create Chan Request

Add processing L2CAP Create Chan Request. When channel is created
save associated high speed link hs_hcon.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Use l2cap_physical_cfm in phylink complete evt

When receiving HCI Phylink Complete event run amp_physical_cfm
which initialize BR/EDR L2CAP channel associated with High Speed
link and run l2cap_physical_cfm which shall send L2CAP Create
Chan Request.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Check for hs_hcon instead of ctrl_id

When deciding whether to send EFS configuration response with success,
check rather for existence of High Speed physical link hs_hcon then
ctrl_id. There might be cases when there is ctrl_id but high speed link
is not established yet.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Disconnect logical link when deleting chan

Disconnect logical link for high speed channel hs_hchan
associated with L2CAP channel chan.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Remove hci_conn receiving error command status

When receiving HCI Event: Command Status for Create Physical Link
with Error code remove AMP hcon.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Process Disc Physical Link Complete evt

Add processing for HCI Disconnection Physical Link Complete Event.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Process Disc Logical Link

Add processing for HCI Disconnection Logical Link Complete
Event.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Add Logical Link Create function

After physical link is created logical link needs to be created.
The process starts after L2CAP channel is created and L2CAP
Configuration Response with result PENDING is received.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Derive remote and local amp id from chan struct

l2cap_chan already keeps information about *_amp_id.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Return correct L2CAP response type

Return L2CAP_CREATE_CHAN_RSP for Create Channel Request and
L2CAP_CONN_RSP for Create Connection Request.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Save hs_hchan instead of hs_hcon in loglink complete

When logical link creation is completed we need to save hs_hchan
which represents logical link instead of hs_hcon representing
physical link. hs_hcon shall be saved when receiving physical link
complete event.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: trivial: Fix braces style and remove empty line

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: mgmt: Use __constant when dealing with constants

__constant_cpu_to_le*() is the right go here.

Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Remove unnecessary include export.h

For files only using THIS_MODULE and/or EXPORT_SYMBOL, map
them onto including export.h -- or if the file isn't even
using those, then just delete the include.

Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add put(hcon) when deleting hchan

When refcnt reaches zero disconnect timeout will run and hci_conn
will be disconnected.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Process Logical Link complete evt

After receiving HCI Logical Link Complete event finish EFS
configuration by sending L2CAP Conf Response with success code.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: AMP: Process Physical Link Complete evt

Add processing for HCI Physical Link Complete event. Upon
successful status received start L2CAP create channel process.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Use helper function sending EFS conf rsp

There is helper function used to send EFS Configuration Response.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: trivial: Remove unneeded assignment

Assignment is not needed here since err is always gets value.

Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix sending unnecessary HCI_LE_Host_Enable

This patch fixes sending an unnecessary HCI_LE_Host_Enable command if
the command has already been sent as part of the default HCI init
sequence.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix unnecessary EIR update during powering on

When powered on the EIR data gets updated as the last step by mgmt.
Therefore avoid an update when getting a local name update as that's
part of the normal HCI init sequence.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix sending unnecessary HCI_Write_SSP_Mode command

This patch fixes sending an unnecessary HCI_Write_SSP_Mode command if
the command has already been sent as part of the default HCI init
sequence.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix setting host feature bits for SSP

When we get a successful command complete for HCI_Write_SSP_Mode we need
to update the host feature bits for the hdev struct accordingly.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Disallow LE scanning and connecting in peripheral role

When an adapter is in the LE peripheral role scanning for other devices
or initiating connections to them is not allowed. This patch makes sure
that such attempts will result in appropriate error returns.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add flag for LE GAP Peripheral role

This patch adds a flag to be used for LE GAP Peripheral role. In this
role undirected advertising will be enabled and operations not allowed
in Peripheral role (such as scanning and initiating connections) will be
disallowed.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Make use feature test macros

For better code readability and avoiding simple bugs of checking the
wrong byte of the features make use of feature test macros whenever
possible.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Add missing feature test macros

This patch adds missing feature test macros needed for various use cases
and also sorts the macros according to the feature bit location in the
feature mask (for easy lookup).

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix updating host feature bits for LE

When LE has been enabled with the simultaneous BR/EDR & LE parameter set
to true we should also update the host features stored in struct hci_dev
accordingly.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: mgmt: Restrict BR/EDR settings to BR/EDR-only adapters

This patch makes sure that settings which are specific for BR/EDR
capable adapters are not allowed for non-BR/EDR (e.g. LE-only) adapters.
Instead, a "not supported" error is returned of such a setting is
attempted to be set for a non-BR/EDR adapter.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth: Fix HCI command sending when powering on LE-only adapters

This patch makes sure that we don't send BR/EDR-only commands for
LE-only adapters when they get powered on. Doing this would just cause
command errors.

Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

Bluetooth:Replace list_for_each with list_for_each_entry() helper

Replace list_for_each with list_for_each_entry() helper

Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>

ar5523: make buffer size variable unsigned

A negative buffer size doesn't make sense and it breaks this check in
ar5523_get_max_rxsz():

if (!ar->rxbufsz || ar->rxbufsz > AR5523_SANE_RXBUFSZ) { ...

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: rtl8192ce: rtl8192cu: rtl8192se: rtl8192de: Shorten some variable names

The private data areas for these drivers contain some very long variable
names that cause difficulty in fitting source lines to an 80-character
limit.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: rtl8192c: rtl8192ce: Add support for B-CUT version of RTL8188CE

Realtek devices with designation RTL8188CE-VL have the so-called B-cut
of the wireless chip. This patch adds the special programming needed by
these devices. In addition, a variable that was static has been moved into
the private data area as it is now needed in two different routines. This
change also fixes a minor bug that would be present if a system had more
than one RTL81{88,92}CE devices. Other drivers in the rtlwifi family had
already made this change, thus the variable already exists in the private
data structure.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Anisse Astier <anisse@astier.eu>
Cc: Li Chaoming <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless

Conflicts:
drivers/net/wireless/mwifiex/cfg80211.c

ssb: handle BCM43222 in pmu code.

The BCM43222 with the chipid 43222 or 0xa8d6 in hex do not need any
special handling in the pmu code. This prevents some error messages
being shown.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: add PCI ID 0x4350

14e4:4350 is found on a Broadcom BCM43222.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Dump BTCOEX tuning parameters

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: validate MCI stuck after RTC wakeup

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix concurrent tx on lower tx power

Whenever WLAN receives scheduling msg from BT, it reduces tx power
based on RSSI level. And then BT starts simultaneous transmission
along with WLAN. Sometimes HW MAC compares tx power that is used
prior to power reduction which is causing BT transmission to defer.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable hw PLL power save for AR9565

This reduced the power consumption to half in full and network sleep.

Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable hw PLL power save for AR9462

This reduced the power consumption to half in full and network sleep.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@chromium.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ar5523: Add new driver

This driver is for the AR5523 chipset from Atheros. It was created
in 2007 by Christoph Hellwig but it was never finished. I found it a
couple of months ago and after some polishing it's working pretty
fine.

The driver was written with the FreeBSD driver (uath) as reference,
which was written with the reverse-engineered windows driver as
reference, hence the feature set is very limited. Station mode
only, no HW crypto offload.

Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: store IEs per virtual interface

For AP feature the IEs are stored in global structure. For future
functionality like P2P-GO it needs to be stored per virtual interface
so better store it in the virtual interface structure.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unnecessary macro usage in brcmf_cfg80211_resume()

The macro wiphy_to_cfg() is a bit redundant as the function already
has a pointer variable to brcmf_cfg80211_info structure.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: add virtual interface support in brcmf_cfg80211_suspend()

With multiple interfaces suspend will need to iterate over all and
bring down the link.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use memset when setting a broadcast mac address

The driver had a global constant ether_bcast, which was copied
whenever a broadcast mac address was needed. This patch does a
memset(dest, 0xFF, ETH_ALEN) instead and consequently removes
the global ether_bcast.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: rename check_sys_up() to check_vif_up()

The function now return the status for a virtual interface so
it seems better rename the function to understand what it does.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove unused enumeration wl_prof_list

The enumeration wl_prof_list is no longer used so it can be safely
removed.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: cleanup brcmf_cfg80211_profile structure

A couple of unused fields have been removed and kernel-doc info has
been added to the structure.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: remove debugfs functionality from wl_cfg80211.c

In wl_cfg80211.c debugfs directory was created to expose
dtim_period and beacon_interval. However, this can be easily
obtained using iw so it is removed from the driver.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: separate connection status from scanning status

The connection status is to be kept per virtual interface and
the scanning status is for device. So they need to be separated
for multiple interface support.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: use vif struct to check_sys_up() function

This checks the status that will soon be moved to virtual
interface data so preparing for that use the structure
brcmf_cfg80211_vif as parameter instead.

Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meulemen <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

brcmfmac: store profile information per virtual interface

The profile information applies to an interface so each virtual
interface needs it. So it is removed from brcmf_cfg80211_info
and added to brcmf_cfg80211_vif structure.

Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>