iwlwifi: mvm: support new Coex firmware API

The firmware now adds more information about time sharing
with the Bluetooth core.
Adapt the API structures and add the new fields in the
debugfs hooks.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: call iwl_remove_notification from iwl_wait_notification

The iwl_wait_notification() function removes the wait entry from the
list.  To make it clearer that it's doing the same thing as
iwl_remove_notification(), call the latter instead of having duplicate
code.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: consider RFKILL during INIT as success

There's no need to differentiate an INIT that ended early because of
RFKILL from one that succeded.  Additionally, if INIT fails later,
during calibration, due to RFKILL, we can just return success and
continue as if we were already in RFKILL to start with.

Remove this unnecessary differentiation and do some other small
clean-ups while at it.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove the corunning support

The corunning block was supposed to help in coex scenarios.
It required the driver to configure the firmware based on
the coupling between the two antennas of the devices.
This was never in use and the configuration sent by the
driver has always been blank.
Remove all that code.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

rsi: security enhancements for AP mode

Station id should be set in load key frame configured to device.
For WEP mode, key is configured once from mac80211. This key is
saved and configured to device every time a station is connected.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: aggregation parameters frame for AP mode

TX command frame ampdu aggregation parameters is updated to
include sta_id for AP mode.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: update tx auto rate command frame for AP mode

Auto rate frame is sent to firmware when a new station is
connected. Station id and station's ht capabilities are updated
in auto rate command frame.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: use common descriptor for auto rate frame

TX command frame auto rate request is modified to use common
descriptor struture.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: data and managemet path changes for AP mode

Station id needs to be get for data and management frames
to fill in the descruptor for AP mode. Few other changes
related to AP mode are covered here.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: handle station disconnection in AP mode

When sta_remove of mac80211 is called, driver iterates through
list of existing stations to get the station id. Then peer notify
is prepared and send to firmare.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: handle station connection in AP mode

Station structures are maintained in driver with required
fields. When mac80211 callback sta_add is called, driver
iterates through list of connected stations to check available
index and assigns station id which is important for further
communication to that station. Then peer notify frame is send
to firmware to inform the firmware about new station connection.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add beacon changes for AP mode

Mac80211 config parameter BEACON_ENABLE is handled. When VAP
capabilities frame with AP mode is configured to firmware, beacon
events start coming to host at each PreTBTT. At this time, beacon
is taken from mac80211, descriptor is prepared and send to firmware.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: remove interface changes for AP mode

remove_interface callback of mac80211 is handled for AP mode.
Same is notified to firmware through vap_capabilities frame
with VAP status VAP_DELETE.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add interface changes for ap mode

AP mode is handled in add_interface callback of mac80211.
Also for AP mode, sending rx filter frame to disallow beacons
to host is added. Station structures are initialized to NULL.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: advertise ap mode support

AP mode support is advertised to cfg80211. Necessary wiphy
parameters are initialized.

Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: modify tx reclaim locking

Perform additional reclaim from qtnf_pcie_data_tx. Lock tx_lock serves only
reclaim synchronization purposes. Rename it accordingly and improve
granularity moving this lock to qtnf_pcie_data_tx_reclaim.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: introduce counter for Rx underflow events

Introduce counter for Rx underflow events. Export this counter via debugfs.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: switch to kernel circ_buf implementation

Current code for both Rx and Tx queue management is a custom and incomplete
circular buffer implementation. It makes a lot of sense to switch to kernel
built-in circ_buf implementation.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: decrease default Tx queue size

Avoid extra buffering in driver by default. Use max hardware Tx queue size.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: skb2rbd_attach cleanup

Update PCIE_HDP_TX_HOST_Q_WR_PTR register in skb2rbd_attach as a part of
procedure of passing new Rx buffer to hardware. Sync up all the the
qtnf_rx_bd descriptor updates before passing Rx buffer to hardware.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: use __netdev_alloc_skb_ip_align

Replace __dev_alloc_skb and explicit NET_IP_ALIGN alignment by built-in
__netdev_alloc_skb_ip_align function.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: switch to napi_gro_receive

Use napi_gro_receive() rather than netif_receive_skb() to improve
performance when GRO is enabled.

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

qtnfmac: remove unused qtnf_rx_frame declaration

Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: check for NL80211_SCAN_FLAG_RANDOM_ADDR during hidden SSID scan

At the end of user scan request, driver will perform an active
scan for hidden SSIDs in passive channels. While doing this,
driver unconditionally adding random_mac in scan command, which
is no expected. It should add random_mac only if scan_request
has NL80211_SCAN_FLAG_RANDOM_ADDR flag set.

Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: do not use random MAC for pre-association scanning

Driver should use random MAC address only if the scan is
requested by user(provided NL80211_SCAN_FLAG_RANDOM_ADDR
is set in scan request). It should not be used for a scan
performed before association.

Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2017-08-11' of git://git./linux/kernel/git/iwlwifi/iwlwifi-next

Sencond batch of iwlwifi patches for 4.14

* Some more code moved to a new directory;
* Fixes in LED handling;
* Some FW API updates;
* General fixes and cleanups here and there.

brcm80211: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: uap: enable 11d based on userspace configruation

This patch check whether userspace beacon data include country
ie, if so then download command to enable 11d setup in firmeare
accordingly.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

zd1211rw: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

zd1201: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtl8192cu: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtl8xxxu: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtl8187: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt73usb: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2800usb: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rt2500usb: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mt7601u: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas_tf: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

libertas: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

p54: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

orinoco: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

at76c50x: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

carl9170: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ar5523: constify usb_device_id

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

iwlwifi: mvm: fix the coex firmware API

The firmware API defined in the header files didn't match
the structure that are actually passed by the firmware.
The impact could be a decision for MIMO in Tx or Rx in
coex scenarios.

Fixes: 430a3bbafdc7 ("iwlwifi: mvm: BT Coex - new API")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: pcie: free the TSO page when a Tx queue is unmapped on A000 devices

When we unmap a non-empty Tx queue, we need to free the
pages that we allocated for the headers in TSO flows.
This code existed for the 9000 device family, but somehow
it got left out when the new Tx path for the A000 devices
was written.

Fixes: 2b0c5946d9ed ("iwlwifi: pcie: introduce a000 TX queues management")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: remove references to unsupported HW

There are still some references to 3945 and 4965 HW, which were never
supported in iwlwifi.  These references were inherited from a previous
project and are irrelevant here.  Additionally, remove some irrelevant
references to 5100 HW.  Remove all these.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: fix nmi triggering from host

Although nmi was triggered fine till now, it appears
that the driver didn't write the exact correct values
to the correct addresses for each HW.
Fix the nmi triggering by setting the correct addresses
and values.

Fixes: 4c9706dc2f29 ("iwlwifi: update nmi register")
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: pcie: don't init a Tx queue with an SSN > size of the queue

The TVQM tells us the initial write pointer for a queue,
but that write pointer is in WiFi sequence number unit
and not in TFD index unit. Which means that the write
pointer in the TVQM's response can be bigger than the
Tx queue ring size.

Fix that by modulo'ing the write pointer from the TVQM
with the Tx queue size.

Fixes: 66128fa08806 ("iwlwifi: move to TVQM mode")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: add station before allocating a queue

One of the queue config params is the associated station id.
Hence the FW must know about the station prior to the queue allocation.
In a000 devices, allocating a queue without a valid station
results with assert 0x2B00.
In FW restart flow the queues are allocated before
adding the station so first add the station.

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: don't send CTDP commands via debugfs if not supported

Fix this issue if it is not supported by the firmware.

Fixes: 00f481bd895a ("iwlwifi: mvm: add ctdp operations to debugfs")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: support new beacon template command

Support a new version of the beacon template command. This replaces v8
of the command, which was missing the rate code.  Also, export rate
decision logic to a separate function.

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: set the default cTDP budget

In case there is no value received from BIOS
for cTDP budget, the default should be 2000 mWatt.

Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: move a000 device NVM retrieval to a common place

Getting the NVM data in a000 devices should be shared
across operation mode.

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: dump smem configuration when firmware crashes

Add the smem configuration to the fw data dump, once
the firmware crashes. This is useful mainly for later
parsing of the smem.

Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: fix a000 RF_ID define

One of the defines has a wrong value.

Fixes: 1afb0ae42174 ("iwlwifi: allow combining different phy images with mac images")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: add support of FPGA fw

Load FW according to NIC type,
taking into account simulation, if exists.
This is determined by a prph register.

Signed-off-by: Tzipi Peres <tzipi.peres@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: fix a few instances of misaligned kerneldoc parameters

There are a few places where we don't have a space between the * and
the @ in the parameter description.  Also, in one case, the @ had
trailing space before the parameter name.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: change functions that can only return 0 to void

Change iwl_set_ucode_api_flags(), iwl_set_ucode_capabilities() to be void.
No need to check returned values.
Found by Klocwork.

Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: add debugfs to force CT-kill

CT-kill is a thermal-based "RF-kill", which disables the NIC
completely if the temperature gets too high, in order to avoid damage.

Add a debugfs entry to simulate high temperatures, in order to test
CT-kill flows in the driver without having to physically heat the
device up.

Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: add const to thermal_cooling_device_ops structure

Declare thermal_cooling_device_ops structure as const as it is only passed
as an argument to the function thermal_cooling_device_register and this
argument is of type const. So, declare the structure as const.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: use firmware LED command where applicable

On devices starting from 8000 series, the host can no longer toggle
the LED through the CSR_LED_REG register, but must do it via the
firmware instead. Add support for this. Note that this means that
the LED cannot be turned on while the firmware is off, so using an
arbitrary LED trigger may not work as expected.

Fixes: 503ab8c56ca0 ("iwlwifi: Add 8000 HW family support")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

iwlwifi: mvm: remove useless condition in LED code

If the module parameter is set to disable the LED, we leave the
initialization routine before setting the LEDS_INIT_COMPLETE
status bit. Therefore, there's no need to check the parameter
again on exit, just the status check is sufficient.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

rt2x00: Fix MMIC Countermeasures

Set RX_FLAG_DECRYPTED in case of MMIC failure so that
ieee80211_rx_h_decrypt() doesnt drop the frame before getting to
ieee80211_rx_h_michael_mic_verify().

Signed-off-by: Michael Skeffington <mike@astro.ai>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rtlwifi: constify rate_control_ops structure

rate_control_ops structure is only passed as an argument to the
function ieee80211_rate_control_{register/unregister}. This argument
is of type const, so declare the structure as const.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wlcore: add const to bin_attribute structure

Add const to bin_attribute structure as it is only passed to the
functions sysfs_{remove/create}_bin_file. The corresponding arguments
are of type const, so declare the structure to be const.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: add setting carrier state ON for successful roaming

After association, ping is not working when sweeping the channel at the
AP side. It is caused by having incorrect carrier state (OFF) for the STA
in successful roaming. This patch sets the carrier state ON for the case.

Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: fix wrong num_different_channels when mchan feature enabled

When the device/firmware supports multi-channel, it can have P2P
connection and regular connection with AP simultaneous. In this case,
the num_different_channels in wiphy info was not correct when firmware
supports multi-channel (The iw wiphy# info showed "#channels <= 1" in
interface combinations). It caused association failed and error message
"CTRL-EVENT-FREQ-CONFLICT error" in wpa_supplicant when P2P GO interface
was running at the same time.
The root cause is that the num_different_channels was always overridden
to 1 in brcmf_setup_ifmodes even multi-channel was enabled.
We correct the logic by moving num_different_channels setting forward.

Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: Add support for CYW4373 SDIO/USB chipset

Add support for CYW4373 SDIO/USB chipset.
CYW4373 is a 1x1 dual-band 11ac chipset with 20/40/80Mhz channel support.
It's a WiFi/BT combo device.

Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

brcmfmac: set wpa_auth to WPA_AUTH_DISABLED in AP/OPEN security mode

When setting wpa_auth to WPA_AUTH_NONE(1) in AP mode with WEP security,
firmware will set privacy bit and add WPA OUI in VENDOR IE in beacon and
probe response. The security type in softAP beacons confuse the
supplicant in client side, and the user client will see [WPA-?] in
supplicant scan result. So we set WPA_AUTH_DISABLED in softAP mode with
OPEN security.

Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: p2p: use separate device address

Per below statement about p2p device address in WFA P2P
spec $2.4.3:

The P2P Device Address of a P2P Device shall be its globally
administered MAC address, or its globally administered MAC
address with the locally administered bit set.

This patch follow above statement, using a separate device
address for p2p interface

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: wrapper wps ie in pass through tlv

This patch wrapper wps ie in pass through tlv, so that
firmware could parse correctly.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: Do not change bss_num in change_virtual_intf

Commit 4d7ab36f0c47 ("mwifiex: Do not change bss_type in
change_virtual_intf") kept original bss_type unchanged. bss_num should
keep the same style, in this way. Unique tuple (bss_type, bss_num) will
be able to locate the right priv structure.

Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

mwifiex: replace netif_carrier_on/off by netif_device_attach/dettach

Driver is doing netif_carrier_off during suspend, which will set
the IFF_LOWER_UP flag to 0. As a result certain applications
will think this as a real carrier down and behave accordingly.
This will cause issues like loss of IP address, for example. To
fix this use netif_device_dettach during suspend.

Fixes: 0026b32d723e ('mwifiex: fix Tx timeout issue during suspend test')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: RTS threshold configuration

Provision is added for configuring RTS threshold by sending
vap dynamic update frame to firmware.

Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: buffer available interrupt handling

BUFFER_AVAILABLE interrupt is sent by firmware to indicate
change in buffer status. We should check buffer status while
handling this interrupt. Currently buffer status is checked
only while dequeueing packets. This patch fixes a data
traffic stuck problem observed occasionally.

Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: buffer full check optimization

We get buffer full event from firmware whenever Tx queue is full
Host should stop writing packets after this and resume after
buffer free event.
Buffer status checking is optimized for once in 4 times if
BUFF_FULL condition is not set, otherwise once for every
packet.

Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: rename sdio_read_buffer_status_register

rsi_sdio_check_buffer_status would be the appropriate name
for this function as we are checking hardware buffers
availability status.

Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add support for U-APSD power save

This patch adds support for U-APSD power save. Configuration
frame is downloaded to firmware with default settings and
support is advertised to mac80211

Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add support for legacy power save

This patch adds support for legacy power save. Necessary
configuration frames are downloaded to firmware when power save
is enabled/disabled

Signed-off-by: Karun Eagalapati <karun256@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: update set_antenna command frame

TX command frame set_antenna is modified to use common
descriptor structure. Also it's subframe type is set.

Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: add support for rf-kill functionality

This patch implements rfkill_poll handler. Also, necessary changes
are done in interface up and down handler to support rfkill
functionality.

Signed-off-by: Pavani Muthyala <pavani.muthyala@redpinesignals.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

rsi: fix uninitialized descriptor pointer issue

This patch fixes the uninitialized descriptor pointer
issue in function rsi_send_internal_mgmt_frame().
Descriptor should point to start of the skb data.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 9a629fafe7d8 ("rsi: immediate wakeup bit and priority for TX command packets")
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bcma: make BCMA a menuconfig to ease disabling it all

No need to get into the submenu to disable all BCMA-related config entries.

Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

net: vrf: Add extack messages for newlink failures

Add extack error messages for failure paths creating vrf devices. Once
extack support is added to iproute2, we go from the unhelpful:
    $  ip li add foobar type vrf
    RTNETLINK answers: Invalid argument

to:
    $ ip li add foobar type vrf
    Error: VRF table id is missing

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

isdn: kcapi: make capi_version const

Declare this structure as const as it is only used during a copy
operation.

Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'Update-DSAs-FDB-API-and-perform-switchdev-cleanup'

Arkadi Sharshevsky says:

====================
Update DSA's FDB API and perform switchdev cleanup

The patchset adds support for configuring static FDB entries via the
switchdev notification chain. The current method for FDB configuration
uses the switchdev's bridge bypass implementation. In order to support
this legacy way and to perform the switchdev cleanup, the implementation
is moved inside DSA.

The DSA drivers cannot sync the software bridge with hardware learned
entries and use the switchdev's implementation of bypass FDB dumping.
Because they are the only ones using this functionality, the fdb_dump
implementation is moved from switchdev code into DSA.

Finally after this changes a major cleanup in switchdev can be done.

Please see individual patches for patch specific change logs.
v1->v2
- Split MDB/vlan dump removal into core/driver removal.

v2->v3
- The self implementation for FDB add/del is moved inside DSA.
====================

Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: switchdev: Remove bridge bypass support from switchdev

Currently the bridge port flags, vlans, FDBs and MDBs can be offloaded
through the bridge code, making the switchdev's SELF bridge bypass
implementation to be redundant. This implies several changes:
- No need for dump infra in switchdev, DSA's special case is handled
  privately.
- Remove obj_dump from switchdev_ops.
- FDBs are removed from obj_add/del routines, due to the fact that they
  are offloaded through the bridge notification chain.
- The switchdev_port_bridge_xx() and switchdev_port_fdb_xx() functions
  can be removed.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: bridge: Remove FDB deletion through switchdev object

At this point no driver supports FDB add/del through switchdev object
but rather via notification chain, thus, it is removed.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Move FDB dump implementation inside DSA

>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove redundant MDB dump support

Currently the MDB HW database is synced with the bridge's one, thus,
There is no need to support special dump functionality.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove support for MDB dump from DSA's drivers

This is done as a preparation before removing support for MDB dump from
DSA core. The MDBs are synced with the bridge and thus there is no
need for special dump operation support.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove support for bypass bridge port attributes/vlan set

The bridge port attributes/vlan for DSA devices should be set only
from bridge code. Furthermore, The vlans are synced totally with the
bridge so there is no need for special dump support.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove support for vlan dump from DSA's drivers

This is done as a preparation before removing support for vlan dump from
DSA core. The vlans are synced with the bridge and thus there is no
need for special dump operation support.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Add support for querying supported bridge flags

The DSA drivers do not support bridge flags offload. Yet, this attribute
should be added in order for the bridge to fail when one tries set a
flag on the port, as explained in commit dc0ecabd6231 ("net: switchdev:
Add support for querying supported bridge flags by hardware").

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Move FDB add/del implementation inside DSA

Currently DSA uses switchdev's implementation of FDB add/del ndos. This
patch moves the implementation inside DSA in order to support the legacy
way for static FDB configuration.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Add support for learning FDB through notification

Add support for learning FDB through notification. The driver defers
the hardware update via ordered work queue. In case of a successful
FDB add a notification is sent back to bridge.

In case of hw FDB del failure the static FDB will be deleted from
the bridge, thus, the interface is moved to down state in order to
indicate inconsistent situation.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove switchdev dependency from DSA switch notifier chain

Currently, the switchdev objects are embedded inside the DSA notifier
info. This patch removes this dependency. This is done as a preparation
stage before adding support for learning FDB through the switchdev
notification chain.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Remove prepare phase for FDB

The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.

The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.

Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>