Nikolay Aleksandrov [Sat, 4 Feb 2017 17:05:07 +0000 (18:05 +0100)]
bridge: move to workqueue gc
Move the fdb garbage collector to a workqueue which fires at least 10
milliseconds apart and cleans chain by chain allowing for other tasks
to run in the meantime. When having thousands of fdbs the system is much
more responsive. Most importantly remove the need to check if the
matched entry has expired in __br_fdb_get that causes false-sharing and
is completely unnecessary if we cleanup entries, at worst we'll get 10ms
of traffic for that entry before it gets deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov [Sat, 4 Feb 2017 17:05:06 +0000 (18:05 +0100)]
bridge: modify bridge and port to have often accessed fields in one cache line
Move around net_bridge so the vlan fields are in the beginning since
they're checked on every packet even if vlan filtering is disabled.
For the port move flags & vlan group to the beginning, so they're in the
same cache line with the port's state (both flags and state are checked
on each packet).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Sat, 4 Feb 2017 16:37:29 +0000 (08:37 -0800)]
bpf: enable verifier to add 0 to packet ptr
The patch fixes the case when adding a zero value to the packet
pointer. The zero value could come from src_reg equals type
BPF_K or CONST_IMM. The patch fixes both, otherwise the verifer
reports the following error:
[...]
R0=imm0,min_value=0,max_value=0
R1=pkt(id=0,off=0,r=4)
R2=pkt_end R3=fp-12
R4=imm4,min_value=4,max_value=4
R5=pkt(id=0,off=4,r=4)
269: (bf) r2 = r0 // r2 becomes imm0
270: (77) r2 >>= 3
271: (bf) r4 = r1 // r4 becomes pkt ptr
272: (0f) r4 += r2 // r4 += 0
addition of negative constant to packet pointer is not allowed
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Mihai Budiu <mbudiu@vmware.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Josef Bacik [Fri, 3 Feb 2017 21:25:23 +0000 (16:25 -0500)]
bpf: test for AND edge cases
These two tests are based on the work done for
f23cc643f9ba. The first test is
just a basic one to make sure we don't allow AND'ing negative values, even if it
would result in a valid index for the array. The second is a cleaned up version
of the original testcase provided by Jann Horn that resulted in the commit.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2017 21:53:30 +0000 (16:53 -0500)]
Merge branch 'dsa-add-fabric-notifier'
Vivien Didelot says:
====================
net: dsa: add fabric notifier
When a switch fabric is composed of multiple switch chips, these chips
must be programmed accordingly when an event occurred on one of them.
Examples of such event include hardware bridging: when a Linux bridge
spans interconnected chips, they must be programmed to allow external
ports to ingress frames on their internal ports.
Another example is cross-chip hardware VLANs. Switch chips in-between
interconnected bridge ports must also configure a given VLAN to allow
packets to pass through them.
In order to support that, this patchset introduces a non-intrusive
notifier mechanism. It adds a notifier head in every DSA switch tree
(the said fabric), and a notifier block in every DSA switch chip.
When an even occurs, it is chained to all notifiers of the fabric.
Switch chips can react accordingly if they are cross-chip capable.
On a dynamic debug enabled system, bridging a port in a multi-chip
fabric will print something like this (ZII Rev B board):
# brctl addif br0 lan3
mv88e6085 0.1:00: crosschip DSA port 1.0 bridged to br0
mv88e6085 0.4:00: crosschip DSA port 1.0 bridged to br0
# brctl delif br0 lan3
mv88e6085 0.1:00: crosschip DSA port 1.0 unbridged from br0
mv88e6085 0.4:00: crosschip DSA port 1.0 unbridged from br0
Currently only bridging events are added. A patchset introducing support
for cross-chip hardware bridging configuration in mv88e6xxx will follow
right after. Then events for switchdev operations are next on the line.
We should note that non-switchdev events do not support rolling-back
switch-wide operations. We'll have to work on closer integration with
switchdev for that, like introducing new attributes or objects, to
benefit from the prepare and commit phases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:21 +0000 (13:20 -0500)]
net: dsa: introduce bridge notifier
A slave device will now notify the switch fabric once its port is
bridged or unbridged, instead of calling directly its switch operations.
This code allows propagating cross-chip bridging events in the fabric.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:20 +0000 (13:20 -0500)]
net: dsa: add switch notifier
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:19 +0000 (13:20 -0500)]
net: dsa: change state setter scope
The scope of the functions inside net/dsa/slave.c must be the slave
net_device pointer. Change to state setter helper accordingly to
simplify callers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:18 +0000 (13:20 -0500)]
net: dsa: rollback bridging on error
When an error is returned during the bridging of a port in a
NETDEV_CHANGEUPPER event, net/core/dev.c rolls back the operation.
Be consistent and unassign dp->bridge_dev when this happens.
In the meantime, add comments to document this behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:17 +0000 (13:20 -0500)]
net: dsa: simplify netdevice events handling
Simplify the code handling the slave netdevice notifier call by
providing a dsa_slave_changeupper helper for NETDEV_CHANGEUPPER, and so
on (only this event is supported at the moment.)
Return NOTIFY_DONE when we did not care about an event, and NOTIFY_OK
when we were concerned but no error occurred, as the API suggests.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Fri, 3 Feb 2017 18:20:16 +0000 (13:20 -0500)]
net: dsa: move netdevice notifier registration
Move the netdevice notifier block register code in slave.c and provide
helpers for dsa.c to register and unregister it.
At the same time, check for errors since (un)register_netdevice_notifier
may fail.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Fri, 3 Feb 2017 16:37:03 +0000 (17:37 +0100)]
net/mlx5e: fix another maybe-uninitialized false-positive
In commit abeffce ("net/mlx5e: Fix a -Wmaybe-uninitialized warning"), I fixed a
gcc warning for the ipv4 offload handling. Now we get the same warning for the
added ipv6 support:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:815:40: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
We can apply the same workaround here as well.
Fixes:
ce99f6b97fcd ("net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Sat, 4 Feb 2017 17:00:49 +0000 (11:00 -0600)]
net-next: treewide use is_vlan_dev() helper function.
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Fri, 3 Feb 2017 09:54:59 +0000 (12:54 +0300)]
net/mlx4_en: fix a condition
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes:
1f8176f7352a ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bert Kenward [Mon, 6 Feb 2017 16:50:55 +0000 (16:50 +0000)]
sfc: don't rearm interrupts if busy polling
Since commit
364b6055738b ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Fri, 3 Feb 2017 09:37:06 +0000 (17:37 +0800)]
sctp: process fwd tsn chunk only when prsctp is enabled
This patch is to check if asoc->peer.prsctp_capable is set before
processing fwd tsn chunk, if not, it will return an ERROR to the
peer, just as rfc3758 section 3.3.1 demands.
Reported-by: Julian Cordes <julian.cordes@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2017 16:25:58 +0000 (11:25 -0500)]
Merge branch 'mlxsw-cleanup-neigh-handling'
Jiri Pirko says:
====================
mlxsw: cleanup neigh handling
Ido says:
This series addresses long standing issues in the mlxsw driver
concerning neighbour reflection. It also prepares the code for follow-up
changes dealing with proper resource cleanup and nexthop reflection.
The first two patches convert the neighbour reflection code to use an
ordered workqueue, to prevent re-ordering of NEIGH_UPDATE events that
may happen following subsequent patches.
The third to fifth patches remove the ndo_neigh_{construct,destroy}
entry points from the driver, thereby relying only on NEIGH_UPDATE
events for neighbour reflection. This simplifies the code considerably.
Last patches are fallout and adjust nits in the code I noticed while
going over it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:17 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Fix typo in comment
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:16 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Don't read 'nud_state' without lock
We periodically ask the neighbouring system to try and resolve
neighbours that are used for nexthops, but aren't currently resolved.
However, 'nud_state' is protected by the neighbour lock, so we shouldn't
access it without taking it. Instead, we can simply check the
'connected' field of the neighbour entry, which we update upon
NEIGH_UPDATE events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:15 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Remove redundant check
We only add neighbour entries that are also used for nexthops to
'nexthop_neighs_list', so when iterating over this list there's no need
to check that the entry is indeed used for nexthops.
Remove the redundant check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:14 +0000 (16:20 +0100)]
net: remove ndo_neigh_{construct, destroy} from stacked devices
In commit
18bfb924f000 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:13 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Simplify neighbour reflection
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:12 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Remove unused variable
Since commit
33b1341cd1bf ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:11 +0000 (16:20 +0100)]
mlxsw: spectrum_router: Use ordered workqueue for neigh updates
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 6 Feb 2017 15:20:10 +0000 (16:20 +0100)]
mlxsw: core: Queue work immediately instead of delaying it
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 6 Feb 2017 16:08:51 +0000 (11:08 -0500)]
Merge tag 'linux-can-next-for-4.11-
20170206' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-02-06
this is a pull request of 16 patches for net-next/master.
The first two patches by David Jander and me add the rx-offload
framework for CAN devices to the kernel. The remaining 14 patches
convert the flexcan driver to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Elad Raz [Mon, 6 Feb 2017 12:56:27 +0000 (13:56 +0100)]
mlxsw: reg: Fix HTGT register length
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jingju Hou [Mon, 6 Feb 2017 06:58:13 +0000 (14:58 +0800)]
net: mvneta: implement .set_wol and .get_wol
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde [Tue, 1 Sep 2015 08:28:46 +0000 (10:28 +0200)]
can: flexcan: switch imx6 and vf610 to timestamp based offloading
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 1 Sep 2015 07:00:13 +0000 (09:00 +0200)]
can: flexcan: add support for timestamp based rx-offload
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 1 Sep 2015 06:57:55 +0000 (08:57 +0200)]
can: flexcan: add quirk FLEXCAN_QUIRK_ENABLE_EACEN_RRS
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 31 Aug 2015 19:03:29 +0000 (21:03 +0200)]
can: flexcan: activate individual RX masking and initialize reg_rximr
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sun, 10 May 2015 13:26:58 +0000 (15:26 +0200)]
can: flexcan: make use of rx-offload's irq_offload_fifo
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Sat, 11 Jul 2015 22:47:47 +0000 (00:47 +0200)]
can: flexcan: make TX mailbox selectable during runtime
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 4 Aug 2015 11:46:10 +0000 (13:46 +0200)]
can: flexcan: calculate default value for imask1 during runtime
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 18 Jan 2017 10:45:14 +0000 (11:45 +0100)]
can: flexcan: flexcan_irq(): don't unconditionally return IRQ_HANDLED
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 18 Jan 2017 10:38:26 +0000 (11:38 +0100)]
can: flexcan: flexcan_poll_bus_err(): fold in do_bus_err()
This patch folds in the do_bus_err() function into
flexcan_poll_bus_err().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Wed, 18 Jan 2017 10:25:41 +0000 (11:25 +0100)]
can: flexcan: flexcan_poll_state(): no need to initialize new_state, rx_state, tx_state
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 17 Jan 2017 16:33:46 +0000 (17:33 +0100)]
can: flexcan: do_bus_err(): convert rx_,tx_errors into bool
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 4 Jul 2016 12:45:44 +0000 (14:45 +0200)]
can: flexcan: make declaration of devtype_data const
This patch changes the declaration of the devtype data to const.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Mon, 4 Jul 2016 12:43:53 +0000 (14:43 +0200)]
can: flexcan: remove write-only member pdata of struct flexcan_priv
This patch removes the write only member pdata from the struct
flexcan_priv.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Thu, 27 Aug 2015 14:01:27 +0000 (16:01 +0200)]
can: flexcan: add missing register definitions
This patch adds some missing register definitions, which are needed in an
upcoming patch.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Marc Kleine-Budde [Tue, 23 Sep 2014 13:28:21 +0000 (15:28 +0200)]
can: rx-offload: Add support for timestamp based irq offloading
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David Jander [Fri, 10 Oct 2014 15:30:10 +0000 (17:30 +0200)]
can: rx-offload: Add support for HW fifo based irq offloading
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
David S. Miller [Sun, 5 Feb 2017 21:11:59 +0000 (16:11 -0500)]
Merge branch 'remove-__napi_complete_done'
Eric Dumazet says:
====================
net: get rid of __napi_complete()
This patch series removes __napi_complete() calls, in an effort
to make NAPI API simpler and generalize GRO and napi_complete_done()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:25:02 +0000 (15:25 -0800)]
net: remove __napi_complete()
All __napi_complete() callers have been converted to
use the more standard napi_complete_done(),
we can now remove this NAPI method for good.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:25:01 +0000 (15:25 -0800)]
aeroflex/greth: use napi_complete_done()
We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:25:00 +0000 (15:25 -0800)]
ibm/emac: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:59 +0000 (15:24 -0800)]
qla3xxx: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:58 +0000 (15:24 -0800)]
ks8695net: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:57 +0000 (15:24 -0800)]
skge: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:56 +0000 (15:24 -0800)]
ep93xx_eth: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:55 +0000 (15:24 -0800)]
pcnet32: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:54 +0000 (15:24 -0800)]
amd8111e: add GRO support
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:53 +0000 (15:24 -0800)]
epic100: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:52 +0000 (15:24 -0800)]
8139cp: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) Eventually get rid of napi_gro_flush() in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 23:24:51 +0000 (15:24 -0800)]
8139too: use napi_complete_done()
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 5 Feb 2017 00:58:15 +0000 (19:58 -0500)]
Merge branch 'ipv6-Improve-user-experience-with-multipath-routes'
David Ahern says:
====================
net: ipv6: Improve user experience with multipath routes
This series closes a couple of gaps between IPv4 and IPv6 with respect
to multipath routes:
1. IPv4 allows all nexthops of multipath routes to be deleted using just
the prefix and length; IPv6 only deletes the first nexthop for the
route if only the prefix and length are given.
2. IPv4 returns multipath routes encoded in the RTA_MULTIPATH attribute.
IPv6 returns a series of routes with the same prefix and length - one
for each nexthop. This happens for both dumps and notifications.
IPv6 does accept RTA_MULTIPATH encoded routes, but installs them as a
series of routes.
Patch 1 addresses the first item by allowing IPv6 multipath routes to be
deleted using just the prefix and length. Patch 2 addresses the second
allowing IPv6 multipath routes to be returned encoded in the RTA_MULTIPATH.
Patches 3 and 4 upate the RTM_{NEW,DEL}ROUTE notifications to generate
1 notification with RTA_MULTIPATH where applicable.
Patch 5 prints IPv6 addresses in compressed format when showing route
replace errors. This was noticed testing REPLACE failures.
The end result for multipath routes:
1. Dump
- RTA_MULTIPATH used for multipath routes
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
...
2. Route Add
- one notification with RTA_MULTIPATH attribute
$ ip -6 ro add vrf red 2001:db8:200::/120 nexthop via 2001:db8:1::2 nexthop via 2001:db8:2::2
$ ip mon route
2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
2. Route Replace
- one notification with RTA_MULTIPATH attribute
$ ip -6 ro replace vrf red 2001:db8:200::/120 nexthop via 2001:db8:1::16 nexthop via 2001:db8:2::16
$ ip mon route
Replaced 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::16 dev eth1 weight 1
nexthop via 2001:db8:2::16 dev eth2 weight 1
- on a failure after the insertion of the first nexthop (which means
the original route has been replaced in the FIB), a notification is
sent with the successful nexthops and then the nexthops are deleted
with one notification per hop. This is consistent with how it works
today except the successful additions are coalesced into 1
notification.
3. Route Delete
- delete of entire multipath route using prefix/length only 1
notification is generated:
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip mon route
Deleted 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::16 dev eth1 weight 1
nexthop via 2001:db8:2::16 dev eth2 weight 1
- if a delete request contains nexthops one notification is
generated per nexthop deleted. This is unavoidable since IPv6
alllows a single nexthop to be deleted within a multipath route
4. Route Appends
- IPv6 allows nexthops to be appended to an existing route. In this
case one notification is sent for the new route with the append
flag set.
$ ip -6 ro append vrf red 2001:db8:200::/120 nexthop via 2001:db8:2::20 nexthop via 2001:db8:1::20
$ ip mon route
Append 2001:db8:200::/120 table red metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
nexthop via 2001:db8:2::20 dev eth2 weight 1
nexthop via 2001:db8:1::20 dev eth1 weight 1
- on failure of an append, a notification is sent with the route
containing all of the nexthops successfully added, and it is
followed by delete notifications as the hops are removed
returning the route to its prior state. This is consistent with
how it works today except the successful additions are coalesced
into 1 notification.
Addresses some of the inconsistencies also noted by Roopa at netdev0.1:
https://www.netdev01.org/docs/prabhu-linux_ipv4_ipv6_inconsistencies_talk_slides.pdf
v4
- changed series to do encoding in 1 patch and updating notificatons
in separate patches to make it easier to review and understand
- 1 notification for delete when using prefix/length; 1 notification for
append
- handle delete of a single nexthop without RTA_MULTIPATH in delete request
- upated commit messages and cover letter
v3
- removed the need for a user API to opt-in to change. Requiring an
API just shifts the difference from same API with different
behavior to different API to achieve equivalent behavior
- route notifications changed to use RTA_MULTIPATH for add and replace
- upated commit messages and cover letter
v2
- fixed locking in patch 1 as noted by DaveM
- changed user API for patch 2 to require an rtmsg with RTM_F_ALL_NEXTHOPS
set in rtm_flags
- revamped explanation of patch 2 and cover letter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:12 +0000 (12:37 -0800)]
net: ipv6: Use compressed IPv6 addresses showing route replace error
ip6_print_replace_route_err logs an error if a route replace fails with
IPv6 addresses in the full format. e.g,:
IPv6: IPV6: multipath route replace failed (check consistency of installed routes): 2001:0db8:0200:0000:0000:0000:0000:0000 nexthop 2001:0db8:0001:0000:0000:0000:0000:0016 ifi 0
Change the message to dump the addresses in the compressed format.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:11 +0000 (12:37 -0800)]
net: ipv6: Change notifications for multipath delete to RTA_MULTIPATH
If an entire multipath route is deleted using prefix and len (without any
nexthops), send a single RTM_DELROUTE notification with the full route
using RTA_MULTIPATH. This is done by generating the skb before the route
delete when all of the sibling routes are still present but sending it
after the route has been removed from the FIB. The skip_notify flag
is used to tell the lower fib code not to send notifications for the
individual nexthop routes.
If a route is deleted using RTA_MULTIPATH for any nexthops or a single
nexthop entry is deleted, then the nexthops are deleted one at a time with
notifications sent as each hop is deleted. This is necessary given that
IPv6 allows individual hops within a route to be deleted.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:10 +0000 (12:37 -0800)]
net: ipv6: Change notifications for multipath add to RTA_MULTIPATH
Change ip6_route_multipath_add to send one notifciation with the full
route encoded with RTA_MULTIPATH instead of a series of individual routes.
This is done by adding a skip_notify flag to the nl_info struct. The
flag is used to skip sending of the notification in the fib code that
actually inserts the route. Once the full route has been added, a
notification is generated with all nexthops.
ip6_route_multipath_add handles 3 use cases: new routes, route replace,
and route append. The multipath notification generated needs to be
consistent with the order of the nexthops and it should be consistent
with the order in a FIB dump which means the route with the first nexthop
needs to be used as the route reference. For the first 2 cases (new and
replace), a reference to the route used to send the notification is
obtained by saving the first route added. For the append case, the last
route added is used to loop back to its first sibling route which is
the first nexthop in the multipath route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:09 +0000 (12:37 -0800)]
net: ipv6: Add support to dump multipath routes via RTA_MULTIPATH attribute
IPv6 returns multipath routes as a series of individual routes making
their display and handling by userspace different and more complicated
than IPv4, putting the burden on the user to see that a route is part of
a multipath route and internally creating a multipath route if desired
(e.g., libnl does this as of commit
29b71371e764). This patch addresses
this difference, allowing multipath routes to be returned using the
RTA_MULTIPATH attribute.
The end result is that IPv6 multipath routes can be treated and displayed
in a format similar to IPv4:
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 metric 1024
nexthop via 2001:db8:1::2 dev eth1 weight 1
nexthop via 2001:db8:2::2 dev eth2 weight 1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 20:37:08 +0000 (12:37 -0800)]
net: ipv6: Allow shorthand delete of all nexthops in multipath route
IPv4 allows multipath routes to be deleted using just the prefix and
length. For example:
$ ip ro ls vrf red
unreachable default metric 8192
1.1.1.0/24
nexthop via 10.100.1.254 dev eth1 weight 1
nexthop via 10.11.200.2 dev eth11.200 weight 1
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
$ ip ro del 1.1.1.0/24 vrf red
$ ip ro ls vrf red
unreachable default metric 8192
10.11.200.0/24 dev eth11.200 proto kernel scope link src 10.11.200.3
10.100.1.0/24 dev eth1 proto kernel scope link src 10.100.1.3
The same notation does not work with IPv6 because of how multipath routes
are implemented for IPv6. For IPv6 only the first nexthop of a multipath
route is deleted if the request contains only a prefix and length. This
leads to unnecessary complexity in userspace dealing with IPv6 multipath
routes.
This patch allows all nexthops to be deleted without specifying each one
in the delete request. Internally, this is done by walking the sibling
list of the route matching the specifications given (prefix, length,
metric, protocol, etc).
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
2001:db8:200::/120 via 2001:db8:1::2 dev eth1 metric 1024 pref medium
2001:db8:200::/120 via 2001:db8:2::2 dev eth2 metric 1024 pref medium
...
$ ip -6 ro del vrf red 2001:db8:200::/120
$ ip -6 ro ls vrf red
2001:db8:1::/120 dev eth1 proto kernel metric 256 pref medium
2001:db8:2::/120 dev eth2 proto kernel metric 256 pref medium
...
Because IPv6 allows individual nexthops to be deleted without deleting
the entire route, the ip6_route_multipath_del and non-multipath code
path (ip6_route_del) have to be discriminated so that all nexthops are
only deleted for the latter case. This is done by making the existing
fc_type in fib6_config a u16 and then adding a new u16 field with
fc_delete_all_nh as the first bit.
Suggested-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sat, 4 Feb 2017 15:49:21 +0000 (07:49 -0800)]
virtio_net: exploit napi_complete_done() return value
Since commit
364b6055738b ("net: busy-poll: return busypolling status to
drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
This patch changes virtio_net to use this boolean to avoid a bit of
overhead for busy-poll users.
Jason reports about 1.1% improvement for 1 byte TCP_RR (burst 100).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 Feb 2017 17:13:27 +0000 (12:13 -0500)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-02-03
This series contains updates to i40e/i40evf only.
Jake fixes up the driver to not call i40e_vsi_kill_vlan() or
i40e_vsi_add_vlan() when the PVID is set or when the VID is less than 1.
Cleaned up a check which really is not needed since there is no real
reason why we cannot just call i40e_del_mac_all_vlan() directly. Renamed
functions to better reflect their actual purpose and how they function
in a more clear manner.
Bimmy cleans up unused/deprecated macros.
Mitch cleans up unused device ids which were intended for use when
running Linux VF drivers under Hyper-V, but found to be not needed.
Then cleaned up a function that is no longer needed since the client
open and close functions were refactored. Adds a sleep without timeout
until the reply from the PF driver has been received since the iWARP
client cannot continue until the operation has been completed.
Tushar Dave fixes an issue seen on SPARC where the use of the 'packed'
directive was causing kernel unaligned errors.
Alex does a refactor to pull some data off of the stack and store it
in the transmit buffer info section of the transmit ring.
Alan fixes a bug which was caused by passing a bad register value to the
firmware, by refactoring the macro INTRL_USEC_TO_REG into a static
inline function. Also added feedback to the user as to the actual
interrupt rate limit being used when it differs from the requested limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 3 Feb 2017 22:29:42 +0000 (14:29 -0800)]
net: skb_needs_check() accepts CHECKSUM_NONE for tx
My recent change missed fact that UFO would perform a complete
UDP checksum before segmenting in frags.
In this case skb->ip_summed is set to CHECKSUM_NONE.
We need to add this valid case to skb_needs_check()
Fixes:
b2504a5dbef3 ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 3 Feb 2017 02:43:28 +0000 (18:43 -0800)]
net: remove support for per driver ndo_busy_poll()
We added generic support for busy polling in NAPI layer in linux-4.5
No network driver uses ndo_busy_poll() anymore, we can get rid
of the pointer in struct net_device_ops, and its use in sk_busy_loop()
Saves NETIF_F_BUSY_POLL features bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Feb 2017 22:28:21 +0000 (17:28 -0500)]
enic: Remove local ndo_busy_poll() implementation.
We do polling generically these days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 3 Feb 2017 00:59:18 +0000 (16:59 -0800)]
ixgbevf: get rid of custom busy polling code
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 3 Feb 2017 00:26:39 +0000 (16:26 -0800)]
ixgbe: get rid of custom busy polling code
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Feb 2017 21:58:20 +0000 (16:58 -0500)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree, they are:
1) Stash ctinfo 3-bit field into pointer to nf_conntrack object from
sk_buff so we only access one single cacheline in the conntrack
hotpath. Patchset from Florian Westphal.
2) Don't leak pointer to internal structures when exporting x_tables
ruleset back to userspace, from Willem DeBruijn. This includes new
helper functions to copy data to userspace such as xt_data_to_user()
as well as conversions of our ip_tables, ip6_tables and arp_tables
clients to use it. Not surprinsingly, ebtables requires an ad-hoc
update. There is also a new field in x_tables extensions to indicate
the amount of bytes that we copy to userspace.
3) Add nf_log_all_netns sysctl: This new knob allows you to enable
logging via nf_log infrastructure for all existing netnamespaces.
Given the effort to provide pernet syslog has been discontinued,
let's provide a way to restore logging using netfilter kernel logging
facilities in trusted environments. Patch from Michal Kubecek.
4) Validate SCTP checksum from conntrack helper, from Davide Caratti.
5) Merge UDPlite conntrack and NAT helpers into UDP, this was mostly
a copy&paste from the original helper, from Florian Westphal.
6) Reset netfilter state when duplicating packets, also from Florian.
7) Remove unnecessary check for broadcast in IPv6 in pkttype match and
nft_meta, from Liping Zhang.
8) Add missing code to deal with loopback packets from nft_meta when
used by the netdev family, also from Liping.
9) Several cleanups on nf_tables, one to remove unnecessary check from
the netlink control plane path to add table, set and stateful objects
and code consolidation when unregister chain hooks, from Gao Feng.
10) Fix harmless reference counter underflow in IPVS that, however,
results in problems with the introduction of the new refcount_t
type, from David Windsor.
11) Enable LIBCRC32C from nf_ct_sctp instead of nf_nat_sctp,
from Davide Caratti.
12) Missing documentation on nf_tables uapi header, from Liping Zhang.
13) Use rb_entry() helper in xt_connlimit, from Geliang Tang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Feb 2017 21:35:44 +0000 (16:35 -0500)]
Merge branch 'mlxsw-Introduce-TC-Flower-offload-using-TCAM'
Jiri Pirko says:
====================
mlxsw: Introduce TC Flower offload using TCAM
This patchset introduces support for offloading TC cls_flower and actions
to Spectrum TCAM-base policy engine.
The patchset contains patches to allow work with flexible keys and actions
which are used in Spectrum TCAM.
It also contains in-driver infrastructure for offloading TC rules to TCAM HW.
The TCAM management code is simple and limited for now. It is going to be
extended as a follow-up work.
The last patch uses the previously introduced infra to allow to implement
cls_flower offloading. Initially, only limited set of match-keys and only
a drop and forward actions are supported.
As a dependency, this patchset introduces parman - priority array
area manager - as a library.
v1->v2:
- patch11:
- use __set_bit and __test_and_clear_bit as suggested by DaveM
- patch16:
- Added documentation to the API functions as suggested by Tom Herbert
- patch17:
- use __set_bit and __clear_bit as suggested by DaveM
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:09 +0000 (10:29 +0100)]
mlxsw: spectrum: Implement TC flower offload
Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:08 +0000 (10:29 +0100)]
sched: cls_flower: expose priority to offloading netdevice
The driver that offloads flower rules needs to know with which priority
user inserted the rules. So add this information into offload struct.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:07 +0000 (10:29 +0100)]
mlxsw: spectrum: Introduce ACL core with simple TCAM implementation
Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:06 +0000 (10:29 +0100)]
lib: Introduce priority array area manager
This introduces a infrastructure for management of linear priority
areas. Priority order in an array matters, however order of items inside
a priority group does not matter.
As an initial implementation, L-sort algorithm is used. It is quite
trivial. More advanced algorithm called P-sort will be introduced as a
follow-up. The infrastructure is prepared for other algos.
Alongside this, a testing module is introduced as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:05 +0000 (10:29 +0100)]
list: introduce list_for_each_entry_from_reverse helper
Similar to list_for_each_entry_continue and its reverse variant
list_for_each_entry_continue_reverse, introduce reverse helper for
list_for_each_entry_from.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:04 +0000 (10:29 +0100)]
mlxsw: resources: Add ACL related resources
Add couple of resource limits related to ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:03 +0000 (10:29 +0100)]
mlxsw: spectrum: Introduce basic set of flexible key blocks
Introduce basic set of Spectrum flexible key blocks. It contains blocks
needed to carry all elements defined so far.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:02 +0000 (10:29 +0100)]
mlxsw: core: Introduce flexible actions support
Each entry which is matched during ACL lookup points to an action set.
This action set contains up to three separate actions. If more actions
are needed to be chained, the extended set is created to hold them
in KVD linear area.
This patch implements handling of sets and encoding of actions.
Currectly, only two actions are supported. Drop and forward. Forward
action uses PBS pointer to KVD linear area, so the action code needs to
take care of this as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:01 +0000 (10:29 +0100)]
mlxsw: core: Introduce flexible keys support
Hardware supports matching on so called "flexible keys". The idea is to
assemble an optimal key to use for matching according to the fields in
packet (elements) requested by user. Certain sets of elements are
combined into pre-defined blocks. There is a picker to find needed blocks.
Keys consist of 1..n blocks.
Alongside with that, an initial portion of elements is introduced in order
to be able to offload basic cls_flower rules.
Picked keys are cached so multiple rules could share them.
There is an encode function provided that takes care of encoding key and
mask values according to given key.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:29:00 +0000 (10:29 +0100)]
mlxsw: reg: Add Policy-Engine Extended Flexible Action Register
PEFA register is used for accessing an extended flexible action entry
in the central KVD Linear Database.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:59 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine Policy Based Switching Register
The PPBS register retrieves and sets Policy Based Switching Table entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:58 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine Rules Copy Register
The PRCR register is used for accessing rules within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:57 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine Port Binding Table
The PPBT is used for configuration of the Port Binding Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:56 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine TCAM Entry Register Version 2
The PTCE-V2 register is used for accessing rules within a TCAM region.
It is a new version of PTCE in order to support wider key, mask and
action within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:55 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine TCAM Allocation Register
The PTAR register is used for allocation of regions in the TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:54 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine ACL Group Table register
The PAGT register is used for configuration of the ACL Group Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:53 +0000 (10:28 +0100)]
mlxsw: reg: Add Policy-Engine ACL Register
The PACL register is used for configuration of the ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:52 +0000 (10:28 +0100)]
mlxsw: item: Add helpers for getting pointer into payload for char buffer item
Sometimes it is handy to get a pointer to a char buffer item and use it
direcly to write/read data. So add these helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Fri, 3 Feb 2017 09:28:51 +0000 (10:28 +0100)]
mlxsw: item: Add 8bit item helpers
Item heplers for 8bit values are needed, let's add them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yanjun [Fri, 3 Feb 2017 04:46:21 +0000 (23:46 -0500)]
bonding: Remove unnecessary returned value check
The function bond_info_query alwarys returns 0. As such, in the function
bond_do_ioctl, it is not necessary to check the returned value. So the
interface type of the function bond_info_query is changed to void. The
redundant check is removed.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 3 Feb 2017 04:40:08 +0000 (20:40 -0800)]
tcp: clear pfmemalloc on outgoing skb
Josef Bacik diagnosed following problem :
I was seeing random disconnects while testing NBD over loopback.
This turned out to be because NBD sets pfmemalloc on it's socket,
however the receiving side is a user space application so does not
have pfmemalloc set on its socket. This means that
sk_filter_trim_cap will simply drop this packet, under the
assumption that the other side will simply retransmit. Well we do
retransmit, and then the packet is just dropped again for the same
reason.
It seems the better way to address this problem is to clear pfmemalloc
in the TCP transmit path. pfmemalloc strict control really makes sense
on the receive path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 2 Feb 2017 19:44:27 +0000 (11:44 -0800)]
cxgb4: get rid of custom busy poll code
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 2 Feb 2017 18:50:48 +0000 (10:50 -0800)]
myri10ge: get rid of custom busy poll code
Compared to custom busy_poll, the generic NAPI one is simpler and
removes a lot of code. It removes one atomic in the fast path (when
busy poll is not in action) since we do not have to use an extra
spinlock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 2 Feb 2017 18:16:00 +0000 (10:16 -0800)]
be2net: get rid of custom busy poll code
Compared to custom busy_poll, the generic NAPI one is better, since
it allows to use GRO, and it removes a lot of code and extra locked
operations in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Thu, 2 Feb 2017 16:52:21 +0000 (08:52 -0800)]
net: ipv6: Set protocol to kernel for local routes
IPv6 stack does not set the protocol for local routes, so those routes show
up with proto "none":
$ ip -6 ro ls table local
local ::1 dev lo proto none metric 0 pref medium
local 2100:3:: dev lo proto none metric 0 pref medium
local 2100:3::4 dev lo proto none metric 0 pref medium
local fe80:: dev lo proto none metric 0 pref medium
...
Set rt6i_protocol to RTPROT_KERNEL for consistency with IPv4. Now routes
show up with proto "kernel":
$ ip -6 ro ls table local
local ::1 dev lo proto kernel metric 0 pref medium
local 2100:3:: dev lo proto kernel metric 0 pref medium
local 2100:3::4 dev lo proto kernel metric 0 pref medium
local fe80:: dev lo proto kernel metric 0 pref medium
...
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Thu, 2 Feb 2017 16:09:54 +0000 (17:09 +0100)]
trace: rename trace_print_hex_seq arg and add kdoc
Steven suggested to improve trace_print_hex_seq() a bit after commit
2acae0d5b0f7 ("trace: add variant without spacing in trace_print_hex_seq")
in two ways: i) by adding a kdoc comment for the helper function
itself and ii) by renaming 'spacing' argument into 'concatenate'
to better denote that we don't add spaces between each hex bytes.
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko [Thu, 2 Feb 2017 16:05:04 +0000 (17:05 +0100)]
MAINTAINERS: add Ivan as a switchdev maintainer
Ivan will be taking care of switchdev code from now on.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Feb 2017 20:21:23 +0000 (15:21 -0500)]
Merge branch 'bridge-per-vlan-dst_metadata-support'
Roopa Prabhu says:
====================
bridge: per vlan dst_metadata support
High level summary:
lwt and dst_metadata have enabled vxlan l3 deployments
to use a single vxlan netdev for multiple vnis eliminating the scalability
problem with using a single vxlan netdev per vni. This series tries to
do the same for vxlan netdevs in pure l2 bridged networks.
Use-case/deployment and details are below.
Deployment scerario details:
As we know VXLAN is used to build layer 2 virtual networks across the
underlay layer3 infrastructure. A VXLAN tunnel endpoint (VTEP)
originates and terminates VXLAN tunnels. And a VTEP can be a TOR switch
or a vswitch in the hypervisor. This patch series mainly
focuses on the TOR switch configured as a Vtep. Vxlan segment ID (vni)
along with vlan id is used to identify layer 2 segments in a vxlan
overlay network. Vxlan bridging is the function provided by Vteps to terminate
vxlan tunnels and map the vxlan vni to traditional end host vlan. This is
covered in the "VXLAN Deployment Scenarios" in sections 6 and 6.1 in RFC 7348.
To provide vxlan bridging function, a vtep has to map vlan to a vni. The rfc
says that the ingress VTEP device shall remove the IEEE 802.1Q VLAN tag in
the original Layer 2 packet if there is one before encapsulating the packet
into the VXLAN format to transmit it through the underlay network. The remote
VTEP devices have information about the VLAN in which the packet will be
placed based on their own VLAN-to-VXLAN VNI mapping configurations.
Existing solution:
Without this patch series one can deploy such a vtep configuration by
adding the local ports and vxlan netdevs into a vlan filtering bridge.
The local ports are configured as trunk ports carrying all vlans.
A vxlan netdev per vni is added to the bridge. Vlan mapping to vni is
achieved by configuring the vlan as pvid on the corresponding vxlan netdev.
The vxlan netdev only receives traffic corresponding to the vlan it is mapped
to. This configuration maps traffic belonging to a vlan to the corresponding
vxlan segment.
-----------------------------------
| bridge |
| |
-----------------------------------
|100,200 |100 (pvid) |200 (pvid)
| | |
swp1 vxlan1000 vxlan2000
This provides the required vxlan bridging function but poses a
scalability problem with using a separate vxlan netdev for each vni.
Solution in this patch series:
The Goal is to use a single vxlan device to carry all vnis similar
to the vxlan collect metadata mode but additionally allowing the bridge
and vxlan driver to carry all the forwarding information and also learn.
This implementation uses the existing dst_metadata infrastructure to map
vlan to a tunnel id.
- vxlan driver changes:
- enable collect metadata mode to be used with learning,
replication and fdb
- A single fdb table hashed by (mac, vni)
- rx path already has the vni
- tx path expects a vni in the packet with dst_metadata and relies
on learnt or static forwarding information table to forward the packet
- Bridge driver changes: per vlan dst_metadata support:
- Our use case is vxlan and 1-1 mapping between vlan and vni, but I have
kept the api generic for any tunnel info
- Uapi to configure/unconfigure/dump per vlan tunnel data
- new bridge port flag to turn this feature on/off. off by default
- ingress hook:
- if port is a tunnel port, use tunnel info in
attached dst_metadata to map it to a local vlan
- egress hook:
- if port is a tunnel port, use tunnel info attached to vlan
to set dst_metadata on the skb
Other approaches tried and vetoed:
- tc vlan push/pop and tunnel metadata dst:
- though tc can be used to do part of this, these patches address a deployment
case where bridge driver vlan filtering and forwarding information
database along with vxlan driver forwarding information table and learning
are required.
- making vxlan driver understand vlan-vni mapping:
- I had a series almost ready with this one but soon realized
it duplicated a lot of vlan handling code in the vxlan driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>