Sarah Sharp [Thu, 30 Jan 2014 21:27:49 +0000 (13:27 -0800)]
Revert "xhci: replace xhci_read_64() with readq()"
This reverts commit
e8b373326d8efcaf9ec1da8b618556c89bd5ffc4. Many xHCI
host controllers can only handle 32-bit addresses, and writing 64-bits
at a time causes them to fail. Reading 64-bits at a time may also cause
them to return 0xffffffff, so revert this commit as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Sarah Sharp [Wed, 29 Jan 2014 22:02:00 +0000 (14:02 -0800)]
Revert "xhci: replace xhci_write_64() with writeq()"
This reverts commit
7dd09a1af2c7150269350aaa567a11b06e831003.
Many xHCI host controllers can only handle 32-bit addresses, and writing
64-bits at a time causes them to fail. Rafał reports that USB devices
simply do not enumerate, and reverting this patch helps. Branimir
reports that his host controller doesn't respond to an Enable Slot
command and dies:
[ 75.576160] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 88.991634] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[ 88.991748] xhci_hcd 0000:03:00.0: Abort command ring failed
[ 88.991845] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 93.985489] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 93.985494] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 98.982586] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 98.982591] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 103.979696] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 103.979702] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Reported-by: Branimir Maksimovic <branimir.maksimovic@gmail.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
Sarah Sharp [Wed, 22 Jan 2014 21:35:02 +0000 (13:35 -0800)]
Revert "usbcore: set lpm_capable field for LPM capable root hubs"
Commit
9df89d85b407690afa46ddfbccc80bec6869971d "usbcore: set
lpm_capable field for LPM capable root hubs" was created under the
assumption that all USB host controllers should have USB 3.0 Link PM
enabled for all devices under the hosts.
Unfortunately, that's not the case. The xHCI driver relies on knowledge
of the host hardware scheduler to calculate the LPM U1/U2 timeout
values, and it only sets lpm_capable to one for Intel host controllers
(that have the XHCI_LPM_SUPPORT quirk set).
When LPM is enabled for some Fresco Logic hosts, it causes failures with
a AgeStar 3UBT USB 3.0 hard drive dock:
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:03 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:08 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:08 sg-laptop kernel: usb-storage 3-1:1.0: USB Mass Storage device detected
Jan 11 13:59:08 sg-laptop mtp-probe[613]: checking bus 3, device 2: "/sys/devices/pci0000:00/0000:00:1c.3/0000:04:00.0/usb3/3-1"
Jan 11 13:59:08 sg-laptop mtp-probe[613]: bus: 3, device: 2 was not an MTP device
Jan 11 13:59:08 sg-laptop kernel: scsi6 : usb-storage 3-1:1.0
Jan 11 13:59:13 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U1 failed.
Jan 11 13:59:18 sg-laptop kernel: usb 3-1: Set SEL for device-initiated U2 failed.
Jan 11 13:59:18 sg-laptop kernel: usbcore: registered new interface driver usb-storage
Jan 11 13:59:40 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: device descriptor read/8, error -71
Jan 11 13:59:41 sg-laptop kernel: usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: device descriptor read/8, error -110
Jan 11 13:59:46 sg-laptop kernel: scsi 6:0:0:0: Device offlined - not ready after error recovery
Jan 11 13:59:46 sg-laptop kernel: usb 3-1: USB disconnect, device number 2
lspci for the affected host:
04:00.0 0c03: 1b73:1000 (rev 04) (prog-if 30 [XHCI])
Subsystem: 1043:1039
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at
dd200000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address:
0000000000000000 Data: 0000
Capabilities: [80] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <2us, L1 <32us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 unlimited, L1 unlimited
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Kernel driver in use: xhci_hcd
Kernel modules: xhci_hcd
The commit was backported to stable kernels, and will need to be
reverted there as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Sergey Galanov <sergey.e.galanov@gmail.com>
Cc: stable@vger.kernel.org
Sarah Sharp [Fri, 17 Jan 2014 23:38:12 +0000 (15:38 -0800)]
xhci: Fix resume issues on Renesas chips in Samsung laptops
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable # 2.6.37
Peter Chen [Fri, 10 Jan 2014 05:51:32 +0000 (13:51 +0800)]
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: stable <stable@vger.kernel.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:31 +0000 (13:51 +0800)]
usb: chipidea: need to mask INT_STATUS when write otgsc
For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.
For stable tree: 3.12+
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Ruehl [Fri, 10 Jan 2014 05:51:30 +0000 (13:51 +0800)]
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
hw_phymode_configure configures the PORTSC registers and allow the
following phy_inits to operate on the right parameters. This fix a problem
where the UPLI (ISP1504) could not be detected, because the Viewport was not
available and read the viewport return 0's only.
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Ruehl [Fri, 10 Jan 2014 05:51:29 +0000 (13:51 +0800)]
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
* init the sts flag to 0 (missed)
* fix write the real bit not sts value
* Set PORTCS_STS and DEVLC_STS only if sts = 1
[Peter Chen: This one and the next patch fix the problem occurred imx27
and imx31, and imx27 and imx31 usb support are enabled until 3.14, so
these two patches isn't needed for -stable]
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:28 +0000 (13:51 +0800)]
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
This patch is needed for stable tree 3.11+
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:27 +0000 (13:51 +0800)]
usb: chipidea: add freescale imx28 special write register method
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=
137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:26 +0000 (13:51 +0800)]
usb: ehci: add freescale imx28 special write register method
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=
137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Mon, 13 Jan 2014 10:29:23 +0000 (11:29 +0100)]
usb: core: check for valid id_table when using the RefId feature
When implementing the RefId feature, it was missed that id_tables can be
NULL under special circumstances. Bail out in that case.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Sun, 12 Jan 2014 20:48:53 +0000 (21:48 +0100)]
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
Do not decrement resp_count if it's already 0.
We set resp_count to 0 when the device is closed. The next open and
read will try to clear the WDM_READ flag if there was leftover data
in the read buffer. This fix is necessary to prevent resubmitting
the read URB in a tight loop because resp_count becomes negative.
The bug can easily be triggered from userspace by not reading all
data in the read buffer, and then closing and reopening the chardev.
Fixes:
8dd5cd5395b9 ("usb: cdc-wdm: avoid hanging on zero length reads")
Cc: <stable@vger.kernel.org> # 3.13
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Sun, 12 Jan 2014 09:07:50 +0000 (10:07 +0100)]
usb: core: bail out if user gives an unknown RefId when using new_id
If users use the new RefId feature of new_id, give them an error message
if they provided an unknown reference. That helps detecting typos.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Fri, 10 Jan 2014 18:36:42 +0000 (19:36 +0100)]
usb: core: allow a reference device for new_id
Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Fri, 10 Jan 2014 18:36:41 +0000 (19:36 +0100)]
usb: core: add sanity checks when using bInterfaceClass with new_id
Check if that field is actually used and if so, bail out if it exeeds a
u8. Make it also future-proof by not requiring "exactly three"
parameters in new_id, but simply "more than two".
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Wed, 8 Jan 2014 16:32:44 +0000 (22:02 +0530)]
USB: image: correct spelling mistake in comment
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Wed, 8 Jan 2014 16:30:45 +0000 (22:00 +0530)]
USB: c67x00: correct spelling mistakes in comments
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker [Wed, 8 Jan 2014 16:08:26 +0000 (11:08 -0500)]
usb: delete non-required instances of include <linux/init.h>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shen Guang [Wed, 8 Jan 2014 06:45:42 +0000 (14:45 +0800)]
usb:hub set hub->change_bits when over-current happens
When we are doing compliance test with xHCI, we found that if we
enable CONFIG_USB_SUSPEND and plug in a bad device which causes
over-current condition to the root port, software will not be noticed.
The reason is that current code don't set hub->change_bits in
hub_activate() when over-current happens, and then hub_events() will
not check the port status because it thinks nothing changed.
If CONFIG_USB_SUSPEND is disabled, the interrupt pipe of the hub will
report the change and set hub->event_bits, and then hub_events() will
check what events happened.In this case over-current can be detected.
Signed-off-by: Shen Guang <shenguang10@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 8 Jan 2014 21:45:51 +0000 (13:45 -0800)]
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
This reverts commit
30666249eae3b04875d514dea557d1ab1468c006, as it
depended on a previous patch that I rejected, causing a build error
here. Sorry about that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 8 Jan 2014 20:29:28 +0000 (12:29 -0800)]
Merge tag 'for-usb-next-2014-01-08' of git://git./linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Urgent bug fixes for usb-next and 3.14.
Hi Greg,
Please queue these two patches to usb-next for 3.14.
An xHCI driver fix for USB ethernet devices that went into 3.13 and 3.12
stable is causing usb-storage to go into an infinite loop, and these two
patches fix the issue. I would like these to get into 3.14-rc1 so we
can avoid any potential data corruption for users.
Sarah Sharp
Sarah Sharp [Mon, 6 Jan 2014 21:07:03 +0000 (13:07 -0800)]
xhci: Set scatter-gather limit to avoid failed block writes.
Commit
35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb: xhci: Link TRB
must not occur within a USB payload burst" attempted to fix an issue
found with USB ethernet adapters, and inadvertently broke USB storage
devices. The patch attempts to ensure that transfers never span a
segment, and rejects transfers that have more than 63 entries (or
possibly less, if some entries cross 64KB boundaries).
usb-storage limits the maximum transfer size to 120K, and we had assumed
the block layer would pass a scatter-gather list of 4K entries,
resulting in no more than 31 sglist entries:
http://marc.info/?l=linux-usb&m=
138498190419312&w=2
That assumption was wrong, since we've seen the driver reject a write
that was 218 sectors long (of probably 512 bytes each):
Jan 1 07:04:49 jidanni5 kernel: [ 559.624704] xhci_hcd 0000:00:14.0: Too many fragments 79, max 63
...
Jan 1 07:04:58 jidanni5 kernel: [ 568.622583] Write(10): 2a 00 00 06 85 0e 00 00 da 00
Limit the number of scatter-gather entries to half a ring segment. That
should be margin enough in case some entries cross 64KB boundaries.
Increase the number of TRBs per segment from 64 to 256, which should
result in ring segments fitting on a 4K page.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes:
35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst')
Cc: stable <stable@vger.kernel.org> # 3.12
Ben Hutchings [Mon, 6 Jan 2014 03:16:32 +0000 (03:16 +0000)]
xhci: Avoid infinite loop when sg urb requires too many trbs
Currently prepare_ring() returns -ENOMEM if the urb won't fit into a
single ring segment. usb_sg_wait() treats this error as a temporary
condition and will keep retrying until something else goes wrong.
The number of retries should be limited in usb_sg_wait(), but also
prepare_ring() should not return an error code that suggests it might
be worth retrying. Change it to -EINVAL.
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes:
35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst')
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Wei Yongjun [Tue, 7 Jan 2014 13:40:45 +0000 (21:40 +0800)]
usb: gadget: remove unused variable in gr_queue_int()
The variable 'dev' is initialized but never used
otherwise, so remove the unused variable.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wei Yongjun [Tue, 7 Jan 2014 13:41:15 +0000 (21:41 +0800)]
usb: gadget: s3c-hsotg: remove duplicated include from s3c-hsotg.c
Remove duplicated include.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Leitner [Mon, 6 Jan 2014 20:33:54 +0000 (21:33 +0100)]
USB: ftdi_sio: added CS5 quirk for broken smartcard readers
Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Cc: stable <stable@vger.kernel.org>
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Mon, 6 Jan 2014 02:10:43 +0000 (10:10 +0800)]
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Mon, 6 Jan 2014 02:10:40 +0000 (10:10 +0800)]
usb: doc: rename ci13xxx-imx.txt to ci-hdrc-imx.txt
We have already renamed the file name, change doc name at this
patch.
Cc: devicetree@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Mon, 6 Jan 2014 02:10:39 +0000 (10:10 +0800)]
usb: chipidea: mark register map as "const" and convert to u8
This patch makes the controller register map ci_regs_nolpm and ci_regs_lpm as
"const". Further, as all offset fit into a single byte, the type is changed
from uintptr_t to u8.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Mon, 6 Jan 2014 02:10:38 +0000 (10:10 +0800)]
usb: chipidea: move malloced regmap directly into struct hw_bank
Without this patch a seperate chunk of memory is allocated for the regmap
array. As the regmap is always used it makes no sense to allocate a seperate
memory block for it, this patch moves the regmap array directly into the struct
hw_bank.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 08:41:01 +0000 (14:11 +0530)]
USB: wusbcore: fix up coding style issues in wa-nep.c
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 08:42:24 +0000 (14:12 +0530)]
USB: wusbcore: fix up coding style issues in wa-rpipe.c
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 08:43:10 +0000 (14:13 +0530)]
USB: wusbcore: fix up coding style issues in wusbhc.c and wusbhc.h
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 08:36:31 +0000 (14:06 +0530)]
USB: wusbcore: fix up line break coding style issues in mmc.c
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 08:39:45 +0000 (14:09 +0530)]
USB: wusbcore: fix up line break coding style issues in security.c
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 08:40:24 +0000 (14:10 +0530)]
USB: wusbcore: fix up line break coding style issues in wa-hc.h
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 05:49:04 +0000 (11:19 +0530)]
USB: wusbcore: fix up minor coding style issues in cbaf.c
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 07:07:52 +0000 (12:37 +0530)]
USB: wusbcore: correct spelling mistakes in comments and error string
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Sat, 4 Jan 2014 05:54:41 +0000 (11:24 +0530)]
USB: core: correct spelling mistakes in comments and warning
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 19 Dec 2013 23:44:10 +0000 (15:44 -0800)]
Watchdog: pcwd_usb: remove CONFIG_USB_DEBUG usage
CONFIG_USB_DEBUG is going away, and all of the other USB drivers no
longer rely on "debug" module parameters for debugging lines, so move
the pcwd_usb driver to use the dynamic debug infrastructure to be more
in line with the rest of the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Max Filippov [Wed, 25 Dec 2013 12:01:29 +0000 (16:01 +0400)]
USB: c67x00: move URB private data allocation from under spinlock
This fixes the following warning:
BUG: sleeping function called from invalid context at mm/slub.c:940
in_atomic(): 1, irqs_disabled(): 1, pid: 17, name: khubd
CPU: 0 PID: 17 Comm: khubd Not tainted 3.12.0-00004-g938dd60-dirty #1
__might_sleep+0xbe/0xc0
kmem_cache_alloc_trace+0x36/0x170
c67x00_urb_enqueue+0x5c/0x254
usb_hcd_submit_urb+0x66e/0x724
usb_submit_urb+0x2ac/0x308
usb_start_wait_urb+0x2c/0xb8
usb_control_msg+0x8c/0xa8
hub_port_init+0x191/0x718
hub_thread+0x804/0xe14
kthread+0x72/0x78
ret_from_kernel_thread+0x8/0xc
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Max Filippov [Wed, 25 Dec 2013 12:01:30 +0000 (16:01 +0400)]
USB: c67x00: add proper delays to HPI read/write
According to CY7C67300 specification HPI read and write cycle duration
Tcyc must be at least 6T long, where T is 1/48MHz, which is 125ns.
Without this delay fast host processor cannot write to chip registers.
Add proper ndelay to hpi_{read,write}_reg.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 7 Jan 2014 15:43:02 +0000 (10:43 -0500)]
USB: fix race between hub_disconnect and recursively_mark_NOTATTACHED
There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED(). This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed. When the race occurs, it can cause an oops:
BUG: unable to handle kernel NULL pointer dereference at
0000015c
IP: [<
c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d6082>] usb_set_device_state+0x92/0x120
[<
c16d862b>] usb_disconnect+0x2b/0x1a0
[<
c16dd4c0>] usb_remove_hcd+0xb0/0x160
[<
c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<
c1704efc>] ehci_mid_remove+0x1c/0x30
[<
c1704f26>] ehci_mid_stop_host+0x16/0x30
[<
c16f7698>] penwell_otg_work+0xd28/0x3520
[<
c19c945b>] ? __schedule+0x39b/0x7f0
[<
c19cdb9d>] ? sub_preempt_count+0x3d/0x50
[<
c125e97d>] process_one_work+0x11d/0x3d0
[<
c19c7f4d>] ? mutex_unlock+0xd/0x10
[<
c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
[<
c125f009>] worker_thread+0xf9/0x320
[<
c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<
c125ef10>] ? rescuer_thread+0x2b0/0x2b0
[<
c1264ac4>] kthread+0x94/0xa0
[<
c19d0f77>] ret_from_kernel_thread+0x1b/0x28
[<
c1264a30>] ? kthread_create_on_node+0xc0/0xc0
One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.
To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values. (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.) We also need to
remove the port devices after maxchild has been set to 0, instead of
before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Tue, 7 Jan 2014 11:54:58 +0000 (12:54 +0100)]
USB: fix: ohci-at91 mismerge build error
After commit
99f14bd4d1 "Merge 3.13-rc5 into usb-next" (in linux-next as of
today), I'm getting this error building any at91 kernel:
drivers/usb/host/ohci-at91.c: In function 'usb_hcd_at91_probe':
drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined
goto err;
^
drivers/usb/host/ohci-at91.c: At top level:
drivers/usb/host/ohci-at91.c:206:2: warning: data definition has no type or storage class [enabled by default]
at91_stop_hc(pdev);
^
...
The problem is obviously a mismerge between two unrelated changes that
resulted in missing opening braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:35 +0000 (22:49 +0100)]
USB: oti6858: switch to generic TIOCMIWAIT implementation
Switch to the generic TIOCMIWAIT implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:34 +0000 (22:49 +0100)]
USB: oti6858: only wake up MSR queue on changes
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:33 +0000 (22:49 +0100)]
USB: ch341: clean up interrupt handler
Clean up interrupt completion handler somewhat.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:32 +0000 (22:49 +0100)]
USB: ch341: switch to generic TIOCMIWAIT implementation
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:31 +0000 (22:49 +0100)]
USB: ch341: only wake up MSR queue on changes
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:30 +0000 (22:49 +0100)]
USB: ch341: fix ignored TIOCMIWAIT mask
Make sure the TIOCMIWAIT mask is always honoured.
The CH341 interrupt status has a multiple-status changed flag which
indicates that multiple status changes has occurred since last interrupt
event. Unfortunately, if the final status is the same, there appears to
be no way to determine which signal(s) has changed (an even number of
times).
This means that the multiple-status flag should not be used in
TIOCMIWAIT as it leads to the signal mask argument being ignored (e.g.
TIOCMIWAIT could return if DSR changes twice, even though the user only
cares about carrier changes).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:29 +0000 (22:49 +0100)]
USB: ch341: clean up line-status handling
Clean up line-status handling.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:28 +0000 (22:49 +0100)]
USB: ch341: refactor line-status handling
Refactor line-status handling.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:27 +0000 (22:49 +0100)]
USB: cypress_m8: switch to generic TIOCMIWAIT implementation
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:26 +0000 (22:49 +0100)]
USB: cypress_m8: only wake up MSR queue on changes
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:25 +0000 (22:49 +0100)]
USB: cypress_m8: clean up protocol definitions
Clean up protocol definitions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:24 +0000 (22:49 +0100)]
USB: cypress_m8: fix ring-indicator detection and reporting
Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.
This bug predates git.
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:23 +0000 (22:49 +0100)]
USB: pl2303: switch to generic TIOCMIWAIT implementation
Switch to the generic TIOCMIWAIT implementation which does not suffer
from the races involved when using the deprecated sleep_on functions.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:22 +0000 (22:49 +0100)]
USB: pl2303: only wake up MSR queue on changes
Only wake up MSR wait queue on actual modem-status changes.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:21 +0000 (22:49 +0100)]
USB: pl2303: clean up line-status handling
Clean up line-status handling somewhat.
Get tty-reference only when actually needed.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:20 +0000 (22:49 +0100)]
USB: pl2303: make type data const
Declare constant device-type data as const.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikhail Zolotaryov [Fri, 27 Dec 2013 23:56:35 +0000 (01:56 +0200)]
USB: Nokia 502 is an unusual device
The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170
The workaround is (MAX_SECTORS_64):
rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m
The patch adds the tested device to the unusual list permanently.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Thu, 2 Jan 2014 15:27:56 +0000 (20:57 +0530)]
USB: serial: add support for iBall 3.5G connect usb modem
Add support for iBall 3.5G connect usb modem.
$lsusb
Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY
$usb-devices
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9605 Rev=00.00
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
1234567890ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Thu, 2 Jan 2014 13:59:24 +0000 (19:29 +0530)]
USB: serial: correct spelling mistakes in comments
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Thu, 2 Jan 2014 13:57:47 +0000 (19:27 +0530)]
USB: musb: correct spelling mistakes in comment and error string
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Thu, 2 Jan 2014 13:55:50 +0000 (19:25 +0530)]
USB: misc: idmouse: correct spelling mistake in error string
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Mon, 30 Dec 2013 15:19:19 +0000 (20:49 +0530)]
USB: yurex: fix spelling mistake in comment
fix spelling mistake in comment
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Tue, 31 Dec 2013 16:28:11 +0000 (21:58 +0530)]
USB: chipidea: add guard macro to ci_hdrc_imx.h
Add guard macro to driver/usb/chipidea/ci_hdrc_imx.h
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sachin Kamat [Mon, 30 Dec 2013 05:19:30 +0000 (10:49 +0530)]
usb: ehci: Cleanup usb-ehci-orion.h header
Commit
c02cecb92ed4 ("ARM: orion: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Mon, 30 Dec 2013 14:30:54 +0000 (20:00 +0530)]
USB: iowarrior: fix spelling mistake in comment
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:18 +0000 (19:23 +0100)]
USB: pl2303: use C_CMSPAR macro
Use the new C_CMSPAR macro for consistency.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Lunn [Sun, 29 Dec 2013 18:23:17 +0000 (19:23 +0100)]
USB: serial: add Moxa UPORT 12XX/14XX/16XX driver
Add a driver which supports the following Moxa USB to serial converters:
* 2 ports : UPort 1250, UPort 1250I
* 4 ports : UPort 1410, UPort 1450, UPort 1450I
* 8 ports : UPort 1610-8, UPort 1650-8
* 16 ports : UPort 1610-16, UPort 1650-16
The UPORT devices don't directly fit the USB serial model. USB serial
assumes a bulk in/out endpoint pair per serial port. Thus a dual port
USB serial device is expected to have two bulk in/out pairs. The Moxa
UPORT only has one pair for data transfer and places a header on each
transfer over the endpoint indicating for which port the transfer
relates to. There is a second endpoint pair for events, such as modem
control lines changing state, setting baud rates etc. Again, a
multiplexing header is used on these endpoints.
Some ports need to have a kfifo explicitly allocated since the
framework does not allocate one if there is no associated endpoints.
The framework will however free it on unload of the module.
All data transfers are made on port0, yet the locks are taken on PortN.
urb->context points to PortN, even though the URB is for port0.
Where possible, code from the generic driver is called. However
mxuport_process_read_urb_data() is mostly a cut/paste of
usb_serial_generic_process_read_urb().
The driver will attempt to load firmware from userspace and compare
the available version and the running version. If the available
version is newer, it will be download into RAM of the device and
started. This is optional and the driver appears to work O.K. with
older firmware in the devices ROM.
This driver is based on the MOXA driver and retains MOXAs copyright.
[jhovold@gmail.com: fix get_fw_version error path and some style issues]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Lunn [Sun, 29 Dec 2013 18:23:16 +0000 (19:23 +0100)]
tty: Add C_CMSPAR(tty)
Add the missing C_CMSPAR(tty) macro.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:15 +0000 (19:23 +0100)]
USB: pl2303: use direct baud-rate encoding when possible
Use direct baud-rate encoding rather than divisors for supported baud
rates.
This restores the way baud rates were set prior to commit
8d48fdf689fe
("USB: PL2303: correctly handle baudrates above 115200") which added
divisor encoding, but also switched to the new encoding method for all
baudrates above 115200.
As noted by Frank Schäfer <fschaefer.oss@googlemail.com>, baud rate 500k
was later errounously added to the supported baud-rate table although
it can only be set using divisors.
Note that the current implementation could easily be extended to support
arbitrary non-standard baud rates using divisors (e.g. by falling back
to divisors when the table lookup fails).
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:14 +0000 (19:23 +0100)]
USB: pl2303: add helper function for direct baud-rate encoding
Add helper function for direct baud-rate encoding.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:13 +0000 (19:23 +0100)]
USB: pl2303: refactor baud-rate divisor handling
Refactor baud-rate divisor handling.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:12 +0000 (19:23 +0100)]
USB: pl2303: enforce baud-rate limits before lookup
Enforce any baud-rate limits before doing table lookup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:11 +0000 (19:23 +0100)]
USB: pl2303: refactor baud-rate table lookup
Refactor supported baud-rate table lookup.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:10 +0000 (19:23 +0100)]
USB: pl2303: rename pl2303_encode_baud_rate
Rename baud-rate encoding function to match tty naming.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:09 +0000 (19:23 +0100)]
USB: pl2303: add device-type abstraction
Encode all device-type specifics in a struct rather than testing for
device type and spreading such information throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:08 +0000 (19:23 +0100)]
USB: pl2303: add quirk for legacy devices
Add quirk for legacy devices (type 0 and 1) rather than testing on
device type throughout the driver.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:07 +0000 (19:23 +0100)]
USB: pl2303: clean up type handling
Merge types 0 and 1, whose differences are unknown and have always been
treated the same.
Add TYPE_-prefix to both types.
Test for TYPE_01 (rather than !TYPE_HX) for legacy device quirks.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:06 +0000 (19:23 +0100)]
USB: pl2303: use speed_t for baud rates
Use speed_t for baud rates throughout.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:05 +0000 (19:23 +0100)]
USB: pl2303: add line-status quirk for Siemens phones
Implement line-status handling for Siemens phones as a quirk rather than
spreading such information all over the driver by matching on vendor and
and product ids.
Note that the SIEMENS_PRODUCT_ID_EF81, which was added after the
line-status handling for the other Siemens phones was fixed, might also
need this quirk.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:04 +0000 (19:23 +0100)]
USB: pl2303: remove redundant line-request call
Remove redundant get_line_request (the read back settings are never
used).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:03 +0000 (19:23 +0100)]
USB: pl2303: add error handling to line requests
Refactor and add error handling to line requests.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:02 +0000 (19:23 +0100)]
USB: pl2303: add error handling to set_control_lines
Add error handling to set_control_lines.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:01 +0000 (19:23 +0100)]
USB: pl2303: add error handling to vendor read and write functions
Add error handling and clean up vendor read and write functions.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:23:00 +0000 (19:23 +0100)]
USB: pl2303: clean up driver somewhat
Use u16 rather than __u16.
Fix multi-line comment style.
Remove some comments.
Remove unnecessary whitespace and add some where appropriate.
Drop DRIVER_DESC define.
Merge and simplify multi-line error message.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:59 +0000 (19:22 +0100)]
USB: pl2303: remove bogus delta_msr_wait wake up
Remove bogus MSR wait-queue wake up from process_read_urb which never
updates the MSR flags.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:58 +0000 (19:22 +0100)]
USB: f81232: switch to generic tiocmiwait
Switch to generic tiocmiwait rather than rely on a custom implementation
using racy interruptible_sleep_on().
Note that this driver is mostly stubbed out so neither version of
tiocmiwait will actually work until someone implements
f81232_update_line_status().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:57 +0000 (19:22 +0100)]
USB: f81232: remove bogus call to wake up MSR queue
Remove bogus call to wake up delta_msr_wait from process_read_urb where
the MSR status is never updated (only the LSR bits are masked out).
Comment that the wake-up call should made in f81232_update_line_status
when the MSR status changes.
Note that this driver is still mostly stubbed out.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:56 +0000 (19:22 +0100)]
USB: serial: remove redundant OOM messages
Remove redundant error messages on allocation failures, which have
already been logged.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:55 +0000 (19:22 +0100)]
USB: serial: clean up ioctl debugging
Remove redundant ioctl debugging from subdrivers. The ioctl request code
has already been logged by usb-serial core.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:54 +0000 (19:22 +0100)]
USB: serial: constify device-id tables
Declare device-id tables as const where possible.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:53 +0000 (19:22 +0100)]
USB: pl2303: fix data corruption on termios updates
Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.
The common case was fixed by commit
bf5e5834bffc6 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 3 Jan 2014 20:15:10 +0000 (12:15 -0800)]
Merge tag 'usb-for-v3.14' of git://git./linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
Wei Yongjun [Tue, 24 Dec 2013 11:37:27 +0000 (19:37 +0800)]
usb: phy: keystone: remove redundant return value check of platform_get_resource()
Remove unneeded error handling on the result of a call
to platform_get_resource() when the value is passed to
devm_ioremap_resource().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Ezequiel Garcia [Thu, 26 Dec 2013 12:24:52 +0000 (09:24 -0300)]
usb: musb: Remove usb_disable() check in module_init()
Removing the check to usb_disable() before registering the platform
driver allows to build this driver when !USB && USB_GADGET, to be
used in gadget-only mode.
Also, use module_platform_driver() to register the platform driver.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Greg Kroah-Hartman [Tue, 24 Dec 2013 18:18:03 +0000 (10:18 -0800)]
Merge 3.13-rc5 into usb-next
This resolves the merge issue with drivers/usb/host/ohci-at91.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>