Arnd Bergmann [Tue, 20 Jun 2023 20:38:10 +0000 (22:38 +0200)]
Merge tag 'imx-dt-6.5' of git://git./linux/kernel/git/shawnguo/linux into soc/dt
i.MX ARM device tree for 6.5:
- New board support: Marantec Maveo Box.
- Add HDMI support for TQMa6x/MBa6 board.
- A series from Andrew Lunn to add phy-mode and fixed links for Ethernet
devices on imx51, imx6qdl and vf610.
- A bunch of changes from Fabio Estevam to clean up deprecated and
invalid properies, fix up node names to remove dt-schema warnings.
- A series of maintenance updates for Protonic Holland boards, mostly
on the USB subsystem configuration, thermal zones, and the naming of
GPIO keys.
- Update dma-apbh device node name to remove dtbs_check warnings.
- Remove invalid nodes from fan-controller for a couple of Gateworks
boards.
- Small random updates and clean-ups on various boards.
* tag 'imx-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: imx6qdl: vicut1: rename power to power-button
ARM: dts: imx6dl: prtrvt, prtvt7, prti6q, prtwd2: fix USB related warnings
ARM: dts: imx6dl: plybas: fix USB over-current detection on USB OTG port
ARM: dts: imx6ul: prti6g: fix USB over-current detection on USB OTG port
ARM: dts: imx6qp: prtwd3: Enable USB over current detection on USB OTG port
ARM: dts: imx6dl: prtmvt: fix different USB related warnings
ARM: dts: imx6dl: alti6p: fix different USB related warnings
ARM: dts: imx6dl: vicut1: Address USB related warnings
ARM: dts: imx6dl: Add trip points to thermal zones on several devices
ARM: dts: imx6dl: lanmcu: Configure over-current polarity for USB OTG node
ARM: dts: imx6dl: lanmcu: Disable unused USB PHY nodes
ARM: dts: imx6q: prtwd2: Correct iomux configuration for ENET MDIO and MDC
ARM: dts: imx6dl: prtvt7: Remove touchscreen inversion
ARM: dts: imx6dl: prtvt7: Adjust default backlight brightness to 65
ARM: dts: imx6qdl: vicut1: The sgtl5000 uses i2s not ac97
ARM: dts: imx: Use 'eeprom' as node name
ARM: dts: imx6ul-ccimx6ulsom: Fix the "coin" regulator name
ARM: dts: imx: Use 'pmic' as node name
ARM: dts: imx6: Use the mux- prefix
ARM: dts: imx7d-sdb: Allow UHS modes
...
Link: https://lore.kernel.org/r/20230610072530.418847-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 20 Jun 2023 20:37:32 +0000 (22:37 +0200)]
Merge tag 'imx-bindings-6.5' of git://git./linux/kernel/git/shawnguo/linux into soc/dt
i.MX dt-bindings for 6.5:
- Add vendor prefix for Emtop
- Compatibles for Marantec Maveo Box, i.MX8MM-EVKB and GW7905-2x board.
- Replace tab indent with spaces in fsl.yaml.
* tag 'imx-bindings-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: Add Gateworks i.MX8M GW7905-2x board
dt-bindings: arm: fsl: Fix syntax error
dt-bindings: vendor-prefixes: Add Emtop
dt-bindings: arm: fsl: Add Emtop SoM & Baseboard
dt-bindings: arm: fsl: Add i.MX8MM-EVKB
dt-bindings: arm: fsl: Add Marantec maveo box as a DHCOR i.MX6ULL SoM based board
Link: https://lore.kernel.org/r/20230610072530.418847-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 20 Jun 2023 20:36:26 +0000 (22:36 +0200)]
Merge tag 'sunxi-dt-for-6.5-1' of https://git./linux/kernel/git/sunxi/linux into soc/dt
- fix DCLK clock names
- new board ICnova A20 ADB4006
- add D1 SPI node
- add bluetooth node for chip board
- add extra mmc2 pinmux to sun5i
- add axp209 iio-hwmon node
* tag 'sunxi-dt-for-6.5-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: axp209: Add iio-hwmon node for internal temperature
ARM: dts: sun5i: Add port E pinmux settings for mmc2
ARM: dts: sun5i: chip: Enable bluetooth
riscv: dts: allwinner: d1: Add SPI controllers node
arm: dts: sunxi: Add ICnova A20 ADB4006 board
dt-bindings: arm: sunxi: add ICnova A20 ADB4006 binding
ARM: dts: sunxi: rename tcon's clock output
Link: https://lore.kernel.org/r/20230609210452.GA17638@jernej-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 20 Jun 2023 20:34:46 +0000 (22:34 +0200)]
Merge tag 'tegra-for-6.5-arm64-dt' of git://git./linux/kernel/git/tegra/linux into soc/dt
arm64: tegra: Device tree changes for v6.5-rc1
This introduces support for the IGX Orin and Jetson Orin Nano devices
and enables various additional features on the Jetson AGX Orin and
Jetson Orin NX. This also enables some basic thermal support to prevent
the devices from overheating.
Support for the GPU on the Google Pixel C is enabled and various minor
issues are fixed and cleaned up.
* tag 'tegra-for-6.5-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Enable thermal support on Jetson Orin Nano
arm64: tegra: Enable thermal support on Jetson Orin NX
arm64: tegra: Enable thermal support on Jetson AGX Orin
arm64: tegra: Add Tegra234 thermal support
arm64: tegra: Add a few blank lines for better readability
arm64: tegra: Sort properties more logically
arm64: tegra: Enable GPU on Smaug
arm64: tegra: Add GPU power rail regulator on Smaug
arm64: tegra: Update USB phy-name for Jetson Orin NX
arm64: tegra: Enable USB device for Jetson AGX Orin
arm64: tegra: Add Tegra234 pin controllers
arm64: tegra: Support Jetson Orin Nano Developer Kit
arm64: tegra: Add missing cache properties on Tegra210
arm64: tegra: Fix PCIe regulator for Orin Jetson AGX
arm64: tegra: Add CPU OPP tables and interconnects property
arm64: tegra: Add support for IGX Orin
Link: https://lore.kernel.org/r/20230609193620.2275240-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 20 Jun 2023 20:33:45 +0000 (22:33 +0200)]
Merge tag 'tegra-for-6.5-dt-bindings' of git://git./linux/kernel/git/tegra/linux into soc/dt
dt-bindings: Changes for v6.5-rc1
Several new modules and devices are documented and fixes incorporated
for the Tegra234 GPIO controller pin mappings as well as the possible
Tegra XUDC PHY connections.
* tag 'tegra-for-6.5-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra: Document Jetson Orin Nano Developer Kit
dt-bindings: tegra: Document Jetson Orin Nano
dt-bindings: gpio: Remove FSI domain ports on Tegra234
dt-bindings: usb: tegra-xudc: Remove extraneous PHYs
dt-bindings: tegra: Add ICC IDs for dummy memory clients
dt-bindings: tegra: Document compatible for IGX
Link: https://lore.kernel.org/r/20230609193620.2275240-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 20 Jun 2023 20:31:22 +0000 (22:31 +0200)]
Merge tag 'stm32-dt-for-v6.5-1' of git://git./linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.5, round 1
Highlights:
----------
- MCU/MPU:
- Replace deprecated st,hw-flow-ctrl by uart-has-rtscts.
- Fix LTDC/DSI warnings.
- MPU:
- STMP32MP15:
- Add OTP part number and Vrefint calibration in bsec.
- M4 hold management updated. As SMC call is deprecated,
the service is moved on a SCMI service.
- Add ADC internal channels (VREFINT/VDDCORE).
- ST:
- Enable ADC1&2 on STM32MP15 DKx boards.
- Adopt generic IIO bindings on STM32MP157C ED1
- Add supplies for OV5640 in STM32MP157C EV1
to fix yaml validation.
- Fix i2s bindings to match with the YAML validation (DKx boards).
- DH:
- Rearrange MAC EEPROM.
- Rename AV96 sound card.
- Adopt generic IIo bindings.
- Fix audio routing.
-PHYTEC:
- Add PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM.
This SOM embeds up to 1GB DDR3LP RAM, up to 1GB eMMC,
up to 16 MB QSPI and up to 128 GB NAND flash.
* tag 'stm32-dt-for-v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx
ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2
ARM: dts: stm32: add required supplies of ov5640 in stm32mp157c-ev1
ARM: dts: stm32: Update to generic ADC channel binding on DHSOM systems
ARM: dts: stm32: adopt generic iio bindings for adc channels on dhcor-testbench
ARM: dts: stm32: adopt generic iio bindings for adc channels on dhcor-drc
ARM: dts: stm32: adopt generic iio bindings for adc channels on emstamp-argon
ARM: dts: stm32: adopt generic iio bindings for adc channels on stm32mp157c-ed1
ARM: dts: stm32: enable adc on stm32mp15xx-dkx boards
ARM: dts: stm32: add vrefint support to adc2 on stm32mp15
ARM: dts: stm32: add vrefint calibration on stm32mp15
ARM: dts: stm32: add adc internal channels to stm32mp15
ARM: dts: stm32: fix ltdc warnings in stm32mp15 boards
ARM: dts: stm32: fix dsi warnings on stm32mp15 boards
dt-bindings: display: st,stm32-dsi: Remove unnecessary fields
ARM: dts: stm32: fix warnings on stm32f469-disco board
ARM: dts: stm32: Shorten the AV96 HDMI sound card name
ARM: dts: stm32: fix m4_rproc references to use SCMI for stm32mp15
ARM: dts: stm32: Update Cortex-M4 reset declarations on stm32mp15
ARM: dts: stm32: add STM32MP1-based Phytec board
...
Link: https://lore.kernel.org/r/08d711de-bb6d-a976-735b-5e18b19818ea@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Thierry Reding [Fri, 9 Jun 2023 11:48:38 +0000 (13:48 +0200)]
arm64: tegra: Enable thermal support on Jetson Orin Nano
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 9 Jun 2023 11:45:53 +0000 (13:45 +0200)]
arm64: tegra: Enable thermal support on Jetson Orin NX
Enable the TJ thermal zone and hook up cooling maps for the PWM-
controlled fan and two trip points.
This also removes a duplicate definition of the PWM fan and changes its
cooling levels. This should have no effect, though, because the fan
wasn't previously connected to anything and by default would be turned
off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 26 Jan 2023 13:34:02 +0000 (14:34 +0100)]
arm64: tegra: Enable thermal support on Jetson AGX Orin
Add thermal zone details and enable the PWM fan as cooling device.
Note that this also changes the cooling levels for the PWM fan, which
should have no effect, though, because the fan wasn't previously
connected to anything and by default would be turned off at probe time.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 17 Nov 2022 13:02:30 +0000 (14:02 +0100)]
arm64: tegra: Add Tegra234 thermal support
Add device tree node for the BPMP thermal node on Tegra234 and add
thermal zone definitions.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 9 Jun 2023 10:55:43 +0000 (12:55 +0200)]
arm64: tegra: Add a few blank lines for better readability
Surround device tree nodes with blank lines for increased readability.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Fri, 9 Jun 2023 10:55:42 +0000 (12:55 +0200)]
arm64: tegra: Sort properties more logically
We typically sort the "compatible" property first because it defines
what the remainder of the properties can be. For the sound node on the
Jetson AGX Orin this wasn't done, so fix that up.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Diogo Ivo [Tue, 16 May 2023 08:28:29 +0000 (09:28 +0100)]
arm64: tegra: Enable GPU on Smaug
Enable the GPU on the Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Diogo Ivo [Tue, 16 May 2023 08:28:28 +0000 (09:28 +0100)]
arm64: tegra: Add GPU power rail regulator on Smaug
Add the GPU power rail regulator node for the Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Arnd Bergmann [Fri, 9 Jun 2023 13:00:24 +0000 (15:00 +0200)]
Merge tag 'renesas-dts-for-v6.5-tag2' of git://git./linux/kernel/git/geert/renesas-devel into soc/dt
Renesas DTS updates for v6.5 (take two)
- Add IOMMU support for PCIe devices on R-Car Gen3 and RZ/G2 SoCs,
- Add HSCIF1 serial port support on Renesas ULCB boards equipped with
the Shimafuji Kingfisher extension,
- Miscellaneous fixes and improvements.
* tag 'renesas-dts-for-v6.5-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: ulcb-kf: Add HSCIF1 node
arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1
ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier
arm64: dts: renesas: Add IOMMU related properties into PCIe host nodes
Link: https://lore.kernel.org/r/cover.1686304614.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 9 Jun 2023 12:59:17 +0000 (14:59 +0200)]
Merge tag 'amlogic-arm64-dt-for-v6.5' of https://git./linux/kernel/git/amlogic/linux into soc/dt
Amlogic ARM64 DT changes for v6.4:
- Introduce initial DT for Amlogic C4 SoC based AW409
- add missing cache properties
* tag 'amlogic-arm64-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: add support for C3 based Amlogic AW409
arm64: dts: amlogic: add missing cache properties
dt-bindings: arm: amlogic: add C3 bindings
Link: https://lore.kernel.org/r/37e5de2f-47f1-a3f3-f1e4-4a304192e556@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 9 Jun 2023 12:58:41 +0000 (14:58 +0200)]
Merge tag 'amlogic-arm-dt-for-v6.5' of https://git./linux/kernel/git/amlogic/linux into soc/dt
Amlogic ARM DT changes for v6.5:
- correct uart_B and uart_C clock references for meson8 & meson8b
* tag 'amlogic-arm-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson8: correct uart_B and uart_C clock references
ARM: dts: meson8b: correct uart_B and uart_C clock references
Link: https://lore.kernel.org/r/21b55df9-3eda-0a0f-cf76-79b1d7735314@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 9 Jun 2023 12:57:56 +0000 (14:57 +0200)]
Merge tag 'hisi-arm64-dt-for-6.5' of https://github.com/hisilicon/linux-hisi into soc/dt
ARM64: DT: HiSilicon ARM64 DT updates for v6.5
- Clean up the pinctrl-single node names and correct the #size-cells of
the pinctrl controller nodes
* tag 'hisi-arm64-dt-for-6.5' of https://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: Unify pinctrl-single pin group nodes
Link: https://lore.kernel.org/r/6482C916.1010507@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 9 Jun 2023 12:57:25 +0000 (14:57 +0200)]
Merge tag 'hisi-arm32-dt-for-6.5' of https://github.com/hisilicon/linux-hisi into soc/dt
ARM: DT: HiSilicon ARM32 DT updates for v6.5
- Clean up the pinctrl-single node names and correct the pinctrl
controller nodes of the hi3620 SoC
* tag 'hisi-arm32-dt-for-6.5' of https://github.com/hisilicon/linux-hisi:
ARM: dts: hisilicon: Unify pinctrl-single pin group nodes
Link: https://lore.kernel.org/r/6482C732.3060300@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 9 Jun 2023 12:56:07 +0000 (14:56 +0200)]
Merge tag 'zynq-dt-for-v6.5' of https://github.com/Xilinx/linux-xlnx into soc/dt
ARM: Zynq DT changes for v6.5
- Setup 400k as default i2c frequency
- Wire i2c recovery via gpio on zc702
* tag 'zynq-dt-for-v6.5' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: dts: Add SCL & SDA GPIO entries for recovery
ARM: zynq: dts: Setting default i2c clock frequency to 400kHz
Link: https://lore.kernel.org/r/c5c99ba2-f004-306c-6251-551826f90df8@amd.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Fri, 9 Jun 2023 12:54:32 +0000 (14:54 +0200)]
Merge tag 'omap-for-v6.5/dt-pin-nodes-signed' of git://git./linux/kernel/git/tmlind/linux-omap into soc/dt
Clean-up for pinctrl-single node names for omaps for v6.5
To avoid producing lots of make dtbs checks warnings when the yaml binding
for pinctrl-single gets merged, let's fix up the pin group node names. We
want to do this rather than add non-standard node name workarounds to the
yaml binding.
Also included is a non-urgent fix to move gta04 model name out of the pinmux
node that can wait for the merge window.
* tag 'omap-for-v6.5/dt-pin-nodes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Unify pinctrl-single pin group nodes for dra7
ARM: dts: Unify pinctrl-single pin group nodes for am4
ARM: dts: Unify pinctrl-single pin group nodes for am33xx
ARM: dts: Unify pinctrl-single pin group nodes for ti81xx
ARM: dts: Unify pinctrl-single pin group nodes for omap5
ARM: dts: Unify pinctrl-single pin group nodes for omap4
ARM: dts: Unify pinctrl-single pin group nodes for omap2
ARM: dts: Unify pinctrl-single pin group nodes for omap3
ARM: dts: gta04: Move model property out of pinctrl node
Link: https://lore.kernel.org/r/pull-1685700720-242492@atomide.com-2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Xianwei Zhao [Mon, 15 May 2023 09:32:37 +0000 (17:32 +0800)]
arm64: dts: add support for C3 based Amlogic AW409
Amlogic C3 is an advanced edge AI processor designed for smart IP camera
applications.
Add basic support for the C3 based Amlogic AW409 board, which describes
the following components: CPU, GIC, IRQ, Timer, UART. It's capable of
booting up into the serial console.
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
Link: https://lore.kernel.org/r/20230515093237.2203171-1-xianwei.zhao@amlogic.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Olivier Moysan [Tue, 6 Jun 2023 11:56:04 +0000 (13:56 +0200)]
ARM: dts: stm32: fix i2s endpoint format property for stm32mp15xx-dkx
Use "dai-format" to configure DAI audio format as specified in
audio-graph-port.yaml bindings.
Fixes:
144d1ba70548 ("ARM: dts: stm32: Adapt STM32MP157 DK boards to stm32 DT diversity")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 6 Jun 2023 18:01:12 +0000 (20:01 +0200)]
ARM: dts: stm32: Fix audio routing on STM32MP15xx DHCOM PDK2
The audio routing flow is not correct, the flow should be from source
(second element in the pair) to sink (first element in the pair). The
flow now is from "HP_OUT" to "Playback", where "Playback" is source
and "HP_OUT" is sink, i.e. the direction is swapped and there is no
direct link between the two either.
Fill in the correct routing, where "HP_OUT" supplies the "Headphone Jack",
"Line In Jack" supplies "LINE_IN" input, "Microphone Jack" supplies "MIC_IN"
input and "Mic Bias" supplies "Microphone Jack".
Fixes:
34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Tony Lindgren [Tue, 23 May 2023 06:55:18 +0000 (09:55 +0300)]
arm64: dts: hisilicon: Unify pinctrl-single pin group nodes
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Let's also correct the pinctrl controller #size-cells to 0 while at it.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Tony Lindgren [Tue, 23 May 2023 07:50:34 +0000 (10:50 +0300)]
ARM: dts: hisilicon: Unify pinctrl-single pin group nodes
We want to unify the pinctrl-single pin group nodes to use naming "pins".
Otherwise non-standad pin group names will add make dtbs checks errors
when the pinctrl-single yaml binding gets merged.
Let's also correct the pinctrl controller #size-cells to 0 while at it
and drop unnecessary ranges property.
Cc: Conor Dooley <conor+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Arnd Bergmann [Tue, 6 Jun 2023 15:40:00 +0000 (17:40 +0200)]
Merge tag 'omap-for-v6.5/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into soc/dt
Devicetree changes for omaps for v6.5
A non-urgent fix for gpmc,wait-pin property for am335x-myirtech-myc, and
initial support for Epson Moverio BT-200 AR glasses.
* tag 'omap-for-v6.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4: add initial support for Epson Moverio BT-200
ARM: dts: am335x-myirtech: Add missing NAND wait pin definition
Link: https://lore.kernel.org/r/pull-1685700720-242492@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 6 Jun 2023 15:33:48 +0000 (17:33 +0200)]
Merge tag 'samsung-dt-6.5' of https://git./linux/kernel/git/krzk/linux into soc/dt
Samsung DTS ARM changes for v6.5
1. Final cleanups and improvements as a result of dtbs_checks which rely
on previously merged driver changes thus affecting older or
out-of-tree kernels. The changes are necessary to achieve full
dtbs_check compliance, which justifies affecting out-of-tree users.
Changes affecting them are:
- Drop simple-bus compatible from FIMC: Exynos4 and S5PV210,
- Remove empty camera pinctrl configuration: Exynos4 and S5PV210,
- Re-order MFC clock names to match Exynos and bindings: S5PV210.
2. Except above few more non-intrusive cleanups for dtbs_check for
S5PV210. Fix also some typos.
3. Re-introduce Exynos4212 which was removed because of lack of upstream
users. Artur Weber adds now Samsung Galaxy Tab3 with Exynos4212.
* tag 'samsung-dt-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5pv210: Fix typo in comments, fix pinctrl header
ARM: dts: s3c64xx: Fix some typos in comments
ARM: dts: exynos: Fix some typos in comments
dt-bindings: arm: samsung: Add Samsung Galaxy Tab3 family boards
ARM: dts: exynos: Re-introduce Exynos4212 DTSI
ARM: dts: exynos: Move common Exynos4x12 definitions to exynos4x12.dtsi
ARM: dts: s5pv210: remove empty camera pinctrl configuration
ARM: dts: s5pv210: add dummy 5V regulator for backlight on SMDKv210
ARM: dts: s5pv210: re-order MFC clock names to match Exynos and bindings
ARM: dts: s5pv210: align USB node name with bindings
ARM: dts: s5pv210: align pin configuration nodes with bindings
ARM: dts: exynos: Remove empty camera pinctrl configuration in Odroid X/U3
ARM: dts: exynos: Remove empty camera pinctrl configuration in Universal C210
ARM: dts: exynos: Remove empty camera pinctrl configuration in Trats
ARM: dts: s5pv210: drop simple-bus from FIMC
ARM: dts: exynos: drop simple-bus from FIMC in Exynos4
Link: https://lore.kernel.org/r/20230602091501.15178-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 6 Jun 2023 15:32:01 +0000 (17:32 +0200)]
Merge tag 'at91-dt-6.5' of https://git./linux/kernel/git/at91/linux into soc/dt
AT91 DT for 6.5
It contains:
- gpio-line-names addition for at91-tse850-3 board
- support for SMA connectors on lan966x-pcb8309 board
- use drive-open-drain as boolean property as this is how code handles
it
- generic names for clock controller devices
- use of the new clock controller bindings for at91sam9n12 slow clock
controller
- one blank line removal on sama5d2.dtsi
* tag 'at91-dt-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2: remove extra line
ARM: dts: at91: Return to boolean properties
ARM: dts: lan966x: Add support for SMA connectors
ARM: dts: at91: use clock-controller name for sckc nodes
ARM: dts: at91: at91sam9n12: witch sckc to new clock bindings
ARM: dts: at91: use clock-controller name for PMC nodes
ARM: dts: at91: tse850: add properties for gpio-line-names
Link: https://lore.kernel.org/r/20230530105945.11638-1-claudiu.beznea@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 6 Jun 2023 15:16:30 +0000 (17:16 +0200)]
Merge tag 'ux500-dts-for-v6.5' of git://git./linux/kernel/git/linusw/linux-nomadik into soc/dt
These are some Ux500 DTS updates for the v6.5 kernel cycle:
- Define the SRAM nodes that will be the preferred way to
specify SRAM segments to drivers going forward.
- Fix up the naming of the STMPE nodes as we are merging
proper YAML bindings which puts restrictions on those.
- Disable charging on the Ux500 HREF boards because these
do not have any real batteries connected.
* tag 'ux500-dts-for-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Add eSRAM nodes
ARM: dts: ux500: Fix STMPE device nodes
ARM: dts: ux500: Disable charging on HREF boards
Link: https://lore.kernel.org/r/CACRpkdZ2YLzB-n+1M9u0UqVfct_LAR5cLvYyJhxHsXNR_TFzpQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Jon Hunter [Tue, 30 May 2023 14:02:32 +0000 (15:02 +0100)]
arm64: tegra: Update USB phy-name for Jetson Orin NX
Running 'make dtbs_check' reports the following warning for the Jetson
Orin NX platform ...
arch/arm64/boot/dts/nvidia/tegra234-p3768-0000+p3767-0000.dtb:
usb@3550000: phy-names:1: 'usb3-0' was expected
Fix this by updating the phy-names:1 to be 'usb3-0' as expected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jon Hunter [Tue, 30 May 2023 14:02:31 +0000 (15:02 +0100)]
arm64: tegra: Enable USB device for Jetson AGX Orin
Enable USB device support for the Jetson AGX Orin platform and update
the mode for the usb2-0 port to be on-the-go.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Prathamesh Shete [Mon, 5 Jun 2023 15:42:30 +0000 (17:42 +0200)]
arm64: tegra: Add Tegra234 pin controllers
Add the device tree nodes for the MAIN and AON pin controllers found on
the Tegra234 family of SoCs.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Tue, 16 May 2023 09:58:50 +0000 (11:58 +0200)]
arm64: tegra: Support Jetson Orin Nano Developer Kit
The NVIDIA Jetson Orin Nano Developer Kit is the combination of the
NVIDIA Jetson Orin Nano (P3767, SKU 5) module and the P3768 carrier
board.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Tue, 16 May 2023 09:58:49 +0000 (11:58 +0200)]
dt-bindings: tegra: Document Jetson Orin Nano Developer Kit
The Jetson Orin Nano Developer Kit pairs the Jetson Orin Nano devkit
module with the P3768 carrier board.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Tue, 16 May 2023 09:58:48 +0000 (11:58 +0200)]
dt-bindings: tegra: Document Jetson Orin Nano
The Jetson Orin Nano is the little sibling of the Jetson Orin NX.
Document the corresponding compatible strings for these devices.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Prathamesh Shete [Tue, 30 May 2023 10:51:08 +0000 (12:51 +0200)]
dt-bindings: gpio: Remove FSI domain ports on Tegra234
Ports S, T, U and V are in a separate controller that is part of the FSI
domain. Remove their definitions from the MAIN controller definitions to
get rid of the confusion.
This technically breaks ABI compatibility with old device trees. However
it doesn't cause issues in practice. The GPIO pins impacted by this are
used for non-critical functionality.
Fixes:
a8b10f3d12cfc ("dt-bindings: gpio: Add Tegra234 support")
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
[treding@nvidia.com: rewrite commit message]
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Oleksij Rempel [Tue, 30 May 2023 12:03:45 +0000 (14:03 +0200)]
ARM: dts: imx6qdl: vicut1: rename power to power-button
In order to address the warnings about the naming convention for keys,
this commit renames the 'power' key to 'power-button' in the vicut1-12inch
device tree source file. The warning in question is as follows:
arch/arm/boot/dts/imx6q-vicut1.dtb: gpio-keys: 'power' does not match
any of the regexes:
'^(button|event|key|switch|(button|event|key|switch)-[a-z0-9-]+|[a-z0-9-]+-(button|event|key|switch))$',
'pinctrl-[0-9]+'
The referenced warning originates from the following schema:
Documentation/devicetree/bindings/input/gpio-keys.yaml
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:44 +0000 (14:03 +0200)]
ARM: dts: imx6dl: prtrvt, prtvt7, prti6q, prtwd2: fix USB related warnings
Fix USB-related warnings in prtrvt, prtvt7, prti6q and prtwd2 device trees
by disabling unused usbphynop1 and usbphynop2 USB PHYs and providing proper
configuration for the over-current detection. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port for prtvt7, prti6q
and prtwd2 boards. Only prtrvt do not have OC on USB OTG port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:43 +0000 (14:03 +0200)]
ARM: dts: imx6dl: plybas: fix USB over-current detection on USB OTG port
USB over-current detection is supported on this board. So, activate it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:42 +0000 (14:03 +0200)]
ARM: dts: imx6ul: prti6g: fix USB over-current detection on USB OTG port
USB over-current detection is supported on this board. So, activate it
and fixes the following kernel warnings:
imx_usb 2184200.usb: No over current polarity defined
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:41 +0000 (14:03 +0200)]
ARM: dts: imx6qp: prtwd3: Enable USB over current detection on USB OTG port
The imx6qp-prtwd3 board supports USB over current detection on the USB
OTG port, however, it was previously disabled in the device tree. This
commit enables the over current detection by changing the device tree
setting from 'disable-over-current' to 'over-current-active-low'. This
could potentially protect the USB port from damage due to over current
situations.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:40 +0000 (14:03 +0200)]
ARM: dts: imx6dl: prtmvt: fix different USB related warnings
Fix USB-related warnings in imx6dl prtmvt device tree by disabling
unused usbphynop1 and usbphynop2 USB PHYs and over-current detection
which is not supported on USB h1 port. This fixes the following warnings
with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over current polarity defined
By the way, fix over-current detection on usbotg port.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:39 +0000 (14:03 +0200)]
ARM: dts: imx6dl: alti6p: fix different USB related warnings
Fix USB-related warnings in imx6dl alti6p device tree by disabling
unused usbphynop1 and usbphynop2 USB PHYs and properly configuring
over-current detection on related ports. This fixes the following
warnings with the current kernel:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over-current polarity defined
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:38 +0000 (14:03 +0200)]
ARM: dts: imx6dl: vicut1: Address USB related warnings
This patch addresses several USB-related warnings in the device tree for
the imx6dl vicut1 system. Specifically, it disables the unused
usbphynop1 and usbphynop2 USB PHYs, and disables unsupported
over-current detection. This action mitigates the following kernel
warnings:
usb_phy_generic usbphynop1: dummy supplies not allowed for exclusive requests
usb_phy_generic usbphynop2: dummy supplies not allowed for exclusive requests
imx_usb 2184200.usb: No over-current polarity defined
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:37 +0000 (14:03 +0200)]
ARM: dts: imx6dl: Add trip points to thermal zones on several devices
Kernel v6.3-rc1 prints errors due to missing trip points in thermal
zones. These errors indicate a lack of critical temperature threshold
settings, causing warnings at boot. To silence these errors, this patch
introduces trip points into the thermal zones of several imx6dl based
devices.
The following devices are updated:
- plym2m
- prtvt7
- victgo
- vicut1
These devices are automotive grade and expected to operate up to 105C.
An exception is the plym2m, an industrial grade device, which is
certified to work up to 85C.
The added trip points act as alert thresholds but do not trigger any
actions except warnings. This behavior is by design, as these devices
should maintain their performance until the end, without any thermal
throttling.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:36 +0000 (14:03 +0200)]
ARM: dts: imx6dl: lanmcu: Configure over-current polarity for USB OTG node
This commit adds the 'over-current-active-low' flag to the USB OTG node
in the imx6dl-lanmcu device tree. This flag is necessary because the
hardware signals over-current conditions by pulling the line low.
Without this flag, the kernel could misinterpret an over-current
condition, leading to unexpected behavior.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Tue, 30 May 2023 12:03:35 +0000 (14:03 +0200)]
ARM: dts: imx6dl: lanmcu: Disable unused USB PHY nodes
In the imx6dl-lanmcu system, the usbh2 and usbh3 interfaces are not in
use. However, the related USB PHY nodes (usbphynop1 and usbphynop2) are
enabled by default in the imx6qdl.dtsi file, which can lead to confusion
and potential resource mismanagement.
This commit explicitly disables these unused USB PHY nodes in the
imx6dl-lanmcu device tree, aligning the configuration more accurately
with the actual hardware setup.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Robin van der Gracht [Tue, 30 May 2023 12:03:34 +0000 (14:03 +0200)]
ARM: dts: imx6q: prtwd2: Correct iomux configuration for ENET MDIO and MDC
This commit addresses a misconfiguration in the prtwd2 device tree
source. Specifically, the ENET MDIO and MDC pins were mistakenly
assigned to the Ethernet block, while they are actually used by the I2C4
interface.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
David Jander [Tue, 30 May 2023 12:03:33 +0000 (14:03 +0200)]
ARM: dts: imx6dl: prtvt7: Remove touchscreen inversion
This touchscreen does not seem to be inverted in any axis, so remove these
DT properties.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Robin van der Gracht [Tue, 30 May 2023 12:03:32 +0000 (14:03 +0200)]
ARM: dts: imx6dl: prtvt7: Adjust default backlight brightness to 65
This commit changes the default brightness level of the backlight on the
prtvt7 device from 20 to 65, roughly equivalent to 75% of the maximum
brightness level defined in the "brightness-levels" property.
The adjustment provides a more optimal default brightness for the
device, improving the overall user experience.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Robin van der Gracht [Tue, 30 May 2023 12:03:31 +0000 (14:03 +0200)]
ARM: dts: imx6qdl: vicut1: The sgtl5000 uses i2s not ac97
According to Documentation/devicetree/bindings/sound/fsl,ssi.txt
'fsl,mode' should be specified for AC97 mode only.
The 'fsl,ssi' documentation doesn't say anything about specifying
'sound-dai-cells' so we'll remove that as well.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Mon, 29 May 2023 20:06:45 +0000 (17:06 -0300)]
ARM: dts: imx: Use 'eeprom' as node name
Devicetree node names should be generic. Use 'eeprom' as node name
to avoid devicetree check warning from at24.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 27 May 2023 20:50:48 +0000 (17:50 -0300)]
ARM: dts: imx6ul-ccimx6ulsom: Fix the "coin" regulator name
As documented in pfuze100.yaml, the correct name for the regulator is
"coin", so change it to fix the following DT check warning:
imx6ul-ccimx6ulsbcexpress.dtb: pmic@8: regulators: 'vcoin' does not match any of the regexes:
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 27 May 2023 20:50:47 +0000 (17:50 -0300)]
ARM: dts: imx: Use 'pmic' as node name
Devicetree node names should be generic. Use 'pmic' as node name
to avoid devicetree check warning from pfuze100.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 27 May 2023 16:10:46 +0000 (13:10 -0300)]
ARM: dts: imx6: Use the mux- prefix
According to Documentation/devicetree/bindings/sound/imx-audmux.yaml,
there must be a "mux-" prefix in the audmux port nodes.
Add the "mux-" prefix to avoid devicetree schema warnings.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 27 May 2023 16:06:34 +0000 (13:06 -0300)]
ARM: dts: imx7d-sdb: Allow UHS modes
Describe the SD1_VSELECT pad, which is necessary to allow UHS modes.
Also, to support higher SD card speed modes, describe the 100MHz and
200MHz SD card pinctrl entries.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 27 May 2023 16:06:33 +0000 (13:06 -0300)]
ARM: dts: imx7d-sdb: Describe the SD card regulator
Improve the devicetree description by adding the SD card regulator
that is controlled via GPIO5_2.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Alain Volmat [Thu, 1 Jun 2023 06:52:21 +0000 (08:52 +0200)]
ARM: dts: stm32: add required supplies of ov5640 in stm32mp157c-ev1
Correct the following warnings by adding the required supplies (AVDD, DVDD)
for the ov5640 node.
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'AVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
arch/arm/boot/dts/stm32mp157c-ev1.dtb: camera@3c: 'DVDD-supply' is a required property
From schema: Documentation/devicetree/bindings/media/i2c/ovti,ov5640.yaml
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Tue, 30 May 2023 12:45:37 +0000 (14:45 +0200)]
ARM: dts: stm32: Update to generic ADC channel binding on DHSOM systems
The generic ADC channel binding is recommended over legacy one, update the
DT to the modern binding. No functional change. For further details, see
commit which adds the generic binding to STM32 ADC binding document:
'
664b9879f56e ("dt-bindings: iio: stm32-adc: add generic channel binding")'
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:36 +0000 (14:45 +0200)]
ARM: dts: stm32: adopt generic iio bindings for adc channels on dhcor-testbench
Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR Testbench board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:35 +0000 (14:45 +0200)]
ARM: dts: stm32: adopt generic iio bindings for adc channels on dhcor-drc
Use STM32 ADC generic bindings instead of legacy bindings on
DHCOR DRC Compact board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:34 +0000 (14:45 +0200)]
ARM: dts: stm32: adopt generic iio bindings for adc channels on emstamp-argon
Use STM32 ADC generic bindings instead of legacy bindings on
emtrion GmbH Argon boards.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:33 +0000 (14:45 +0200)]
ARM: dts: stm32: adopt generic iio bindings for adc channels on stm32mp157c-ed1
Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP157c-ed1 board.
The STM32 ADC specific binding to declare channels has been deprecated,
hence adopt the generic IIO channels bindings, instead.
The STM32MP151 device tree now exposes internal channels using the
generic binding. This makes the change mandatory here to avoid a mixed
use of legacy and generic binding, which is not supported by the driver.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:32 +0000 (14:45 +0200)]
ARM: dts: stm32: enable adc on stm32mp15xx-dkx boards
U-Boot enables ADC1&2 to support USB power measurement and ADC
calibration on STM32MP15x Disco boards.
When leaving U-boot the ADCs do not return to power down state
to keep ADC linear calibration available for kernel.
Enable ADC1&2 by default on STM32MP15xx-DKx boards to align kernel
DT with Uboot. This avoids to shutdown the ADCs VDDA, while the
ADCs are not in power down.
Use STM32 ADC generic bindings instead of legacy bindings on
STM32MP15xx-DKx boards.
The ADC pins on Arduino connector are not set by default.
These pins are added in A7 Disco example DTs only.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:31 +0000 (14:45 +0200)]
ARM: dts: stm32: add vrefint support to adc2 on stm32mp15
Set STM32 ADC2 as a consumer of BSEC on STM32MP15, to retrieve
vrefint calibration data saved in OTP.
During the calibration process vrefp is set to 3.3V and the data
acquired is saved to the OTP. This data is used by the ADC driver
to calculated the actual value of vrefp according to the formula:
vrefp = 3.3 x vrefint_cal / vrefint_data
The vrefint channel provides the actual value of vrefp,
which can be used to correct ADC acquisition data.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:30 +0000 (14:45 +0200)]
ARM: dts: stm32: add vrefint calibration on stm32mp15
Describe vrefint calibration cell to be retrieved through bsec.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Tue, 30 May 2023 12:45:29 +0000 (14:45 +0200)]
ARM: dts: stm32: add adc internal channels to stm32mp15
Add STM32 ADC2 internal channels VREFINT and VDDCORE to STM32MP15x SoCs.
VBAT internal channel is not defined by default in SoC DT, and
has be defined in board DT when needed, instead. This avoids unwanted
current consumption on battery, when ADC conversions are performed
on any other channels.
The internal channels are defined in STM32MP15 SoC DT according to the
generic IIO channel bindings. The STM32 driver does not support a mixed
use of legacy and generic channels. When generic channels are defined,
legacy channels are ignored. This involves that the board device trees
using legacy bindings for ADC2, have to be reworked.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Wolfram Sang [Thu, 25 May 2023 08:48:23 +0000 (10:48 +0200)]
arm64: dts: renesas: ulcb-kf: Add HSCIF1 node
Exposed on CN4. Tested by connecting it to a Renesas Ebisu board.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230525084823.4195-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Thu, 25 May 2023 08:48:22 +0000 (10:48 +0200)]
arm64: dts: renesas: ulcb-kf: Remove flow control for SCIF1
The schematics are misleading, the flow control is for HSCIF1. We need
SCIF1 for GNSS/GPS which does not use flow control.
Fixes:
c6c816e22bc8 ("arm64: dts: ulcb-kf: enable SCIF1")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230525084823.4195-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Tue, 23 May 2023 15:35:16 +0000 (17:35 +0200)]
ARM: dts: iwg20d-q7-common: Fix backlight pwm specifier
make dtbs_check:
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7743-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7-dbcm-ca.dtb: backlight: pwms: [[67, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
arch/arm/boot/dts/renesas/r8a7744-iwg20d-q7.dtb: backlight: pwms: [[58, 0, 5000000], [0]] is too long
From schema: Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml
PWM specifiers referring to R-Car PWM Timer Controllers should contain
only two cells.
Fix this by dropping the bogus third cell.
Fixes:
6f89dd9e9325d05b ("ARM: dts: iwg20d-q7-common: Add LCD support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6e5c3167424a43faf8c1fa68d9667b3d87dc86d8.1684855911.git.geert+renesas@glider.be
Yoshihiro Shimoda [Wed, 10 May 2023 09:03:58 +0000 (18:03 +0900)]
arm64: dts: renesas: Add IOMMU related properties into PCIe host nodes
Add iommu-map and iommu-map-mask properties to the PCIe host nodes.
Note that iommu-map-mask should be zero because the IPMMU assigns
one micro TLB ID only, to the PCIe host.
Also change the dma-ranges arguments for IOMMU. Note that dma-ranges
can be used if the IOMMU is disabled.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230510090358.261266-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Krzysztof Kozlowski [Fri, 21 Apr 2023 22:31:52 +0000 (00:31 +0200)]
arm64: tegra: Add missing cache properties on Tegra210
As all level 2 and level 3 caches are unified, add required
cache-unified property to fix warnings like:
tegra210-p2371-0000.dtb: l2-cache: 'cache-unified' is a required property
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Jonathan McDowell [Wed, 10 May 2023 12:02:28 +0000 (13:02 +0100)]
ARM: dts: axp209: Add iio-hwmon node for internal temperature
This adds a DT node to hook up the internal temperature ADC to the
iio-hwmon driver. The various voltage + current ADCs are consumed and
exposed by their respective drivers, but this is not and is always
available. Naming chosen to match the axp20x_ prefix the power sensors
use.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/2a9bd53a65c4a154cccba622c60cbffcdceaeb95.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Jonathan McDowell [Wed, 10 May 2023 12:02:02 +0000 (13:02 +0100)]
ARM: dts: sun5i: Add port E pinmux settings for mmc2
These alternate pins for mmc2 are brought out to the 40 pin U14 header
on the C.H.I.P and can be used to add an external MMC device with a 4
bit interface. See
https://byteporter.com/ntc-chip-micro-sd-slot/
for further details on how.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/7949169f581cab37175602188f44bc26e79a45c0.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Jonathan McDowell [Wed, 10 May 2023 12:01:43 +0000 (13:01 +0100)]
ARM: dts: sun5i: chip: Enable bluetooth
The C.H.I.P has an rtl8723bs device with the bluetooth interface hooked
up on UART3. Support for this didn't exist in mainline when the DTS was
initially added, but it does now, so enable it.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/49ff7f3cc79838a55a89baae09a4ba12c88573fb.1683719613.git.noodles@earth.li
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Martin Blumenstingl [Tue, 16 May 2023 20:30:29 +0000 (22:30 +0200)]
ARM: dts: meson8: correct uart_B and uart_C clock references
On Meson8 uart_B and uart_C do not work, because they are relying on
incorrect clocks. Change the references of pclk to the correct CLKID
(UART1 for uart_B and UART2 for uart_C), to allow use of the two uarts.
This was originally reported by Hans-Frieder Vogt for Meson8b [0], but
the same bug is also present in meson8.dtsi
[0] https://lore.kernel.org/linux-amlogic/trinity-
bf20bcb9-790b-4ab9-99e3-
0831ef8257f4-
1680878185420@3c-app-gmx-bap55/
Fixes:
57007bfb5469 ("ARM: dts: meson8: Fix the UART device-tree schema validation")
Reported-by: Hans-Frieder Vogt <hfdevel@gmx.net> # for meson8b.dtsi
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230516203029.1031174-1-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Andreas Kemnade [Mon, 13 Mar 2023 11:04:09 +0000 (12:04 +0100)]
ARM: dts: omap4: add initial support for Epson Moverio BT-200
Add the devices working with current drivers for the
Epson Moverio BT-200 AR glasses consisting of a control unit
and the glasses itself.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Message-Id: <
20230313110409.2294154-1-andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Alexander Shiyan [Wed, 24 May 2023 09:11:56 +0000 (12:11 +0300)]
ARM: dts: am335x-myirtech: Add missing NAND wait pin definition
The NAND wait pin is connected to the GPMC, but this is not mentioned
in the DT bindings. Let's fix this.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Message-Id: <
20230524091157.775960-1-eagle.alexander923@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Artur Weber [Fri, 19 May 2023 19:06:25 +0000 (21:06 +0200)]
ARM: dts: s5pv210: Fix typo in comments, fix pinctrl header
Change 'specfic' to 'specific' and make the pinctrl DTSI header
more like the s3c64xx pinctrl DTSI (previously it was copied from
the main s5pv210 DTSI, and not changed to match the new contents).
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20230519190625.7844-4-aweber.kernel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Artur Weber [Fri, 19 May 2023 19:06:24 +0000 (21:06 +0200)]
ARM: dts: s3c64xx: Fix some typos in comments
Change 'specfic' to 'specific'.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20230519190625.7844-3-aweber.kernel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Artur Weber [Fri, 19 May 2023 19:06:23 +0000 (21:06 +0200)]
ARM: dts: exynos: Fix some typos in comments
Change 'specfic' to 'specific', 'optiosn' to 'options' and remove
duplicated 'are listed' in DTSI heading comments.
Signed-off-by: Artur Weber <aweber.kernel@gmail.com>
Link: https://lore.kernel.org/r/20230519190625.7844-2-aweber.kernel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Raphael Gallais-Pou [Mon, 29 May 2023 09:13:59 +0000 (11:13 +0200)]
ARM: dts: stm32: fix ltdc warnings in stm32mp15 boards
Those concern:
* "#size-cells" and "#address-cells" wrongly used
* residual "reg" property appearing on endpoints where it could be
avoided
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Raphael Gallais-Pou [Mon, 29 May 2023 09:13:58 +0000 (11:13 +0200)]
ARM: dts: stm32: fix dsi warnings on stm32mp15 boards
Fixes DSI related warnings:
* "#size-cells" and "#address-cells" wrongly used
* Changed 'panel-dsi@0' to 'panel@0' according to dsi-controller.yaml
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Raphael Gallais-Pou [Mon, 29 May 2023 09:13:57 +0000 (11:13 +0200)]
dt-bindings: display: st,stm32-dsi: Remove unnecessary fields
"#address-cells" and "#size-cells" are two properties that are not
mandatory. For instance, the DSI could refer to a bridge outside the scope
of the node rather than include a 'panel@0' subnode. By doing so, address
and size fields become then unnecessary, creating a warning at build time.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Raphael Gallais-Pou [Mon, 29 May 2023 09:13:56 +0000 (11:13 +0200)]
ARM: dts: stm32: fix warnings on stm32f469-disco board
Several warnings appear when building and checking stm32f429 device-tree:
arch/arm/boot/dts/stm32f469-disco.dts:182.28-184.5: Warning (unit_address_vs_reg): /soc/display-controller@
40016800/port/endpoint@0: node has a unit name, but no reg or ranges property
.../arch/arm/boot/dts/stm32f469-disco.dtb: dsi@
40016c00: Unevaluated properties are not allowed ('panel-dsi@0' was unexpected)
From schema: .../Documentation/devicetree/bindings/display/st,stm32-dsi.yaml
Fix those.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Thu, 18 May 2023 00:42:32 +0000 (02:42 +0200)]
ARM: dts: stm32: Shorten the AV96 HDMI sound card name
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes:
e027da342772 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Andrew Lunn [Thu, 25 May 2023 18:26:06 +0000 (20:26 +0200)]
ARM: dts: vf610: ZII: Add missing phy-mode and fixed links
The DSA framework has got more picky about always having a phy-mode
for the CPU port. The Vybrid FEC is a Fast Ethrnet using RMII.
Additionally, the cpu label has never actually been used in the
binding, so remove it.
Lastly, for DSA links between switches, add a fixed-link node
indicating the expected speed/duplex of the link.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Thu, 25 May 2023 01:12:26 +0000 (22:12 -0300)]
ARM: dts: imx6qdl-icore-rqs: Use the 'vmmc-supply' property
'vmcc-supply' is not a valid property.
Use 'vmmc-supply' supply instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 22:46:25 +0000 (19:46 -0300)]
ARM: dts: vfxxx: Remove invalid wdog property
The 'clock-names' property is not a valid property for wdog.
Remove it to fix the following DT check warning:
vf610-zii-ssmb-dtu.dtb: watchdog@
4003e000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: /Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 22:46:24 +0000 (19:46 -0300)]
ARM: dts: imx35: Remove invalid wdog property
The 'clock-names' property is not a valid property for wdog.
Remove it to fix the following DT check warning:
watchdog@
53fdc000: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: Documentation/devicetree/bindings/watchdog/fsl-imx-wdt.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 22:34:40 +0000 (19:34 -0300)]
ARM: dts: imx7d-flex-concentrator: Remove invalid ecspi property
The 'num-chipselects' property is not a valid property for ecspi.
Remove it to fix the following DT check warning:
spi@
30630000: Unevaluated properties are not allowed ('num-chipselects' was unexpected)
From schema: Documentation/devicetree/bindings/spi/fsl-imx-cspi.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 22:26:11 +0000 (19:26 -0300)]
ARM: dts: imx6ull-phytec-tauri: Remove invalid property
The 'rs485-rts-active-high' property is not a valid property and is not
documented anywhere.
Remove it to fix the following DT schema warning:
serial@21f0000: Unevaluated properties are not allowed ('rs485-rts-active-high' was unexpected)
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 13:10:08 +0000 (10:10 -0300)]
ARM: dts: imx7d-smegw01: Pass Ethernet aliases
Pass Ethernet aliases, so that the bootloader can properly pass MAC address
to Linux.
This fixes the problem of getting a random MAC address for eth1 in Linux.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 13:10:07 +0000 (10:10 -0300)]
ARM: dts: imx7d-smegw01: Use pinctrl-0 for pinctrl_rfkill
Use pinctrl-0 for pinctrl_rfkill to fix the following
'make CHECK_DTBS=y imx7d-smegw01.dtb' warning:
regulator-wlan-rfkill: 'pinctrl-0' is a dependency of 'pinctrl-names'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 13:10:06 +0000 (10:10 -0300)]
ARM: dts: imx7d-smegw01: Pass 'gpr' to the pinctrl groups
Pass 'gpr' to the pinctrl groups to fix the following
'make CHECK_DTBS=y imx7d-smegw01.dtb' warning:
pinctrl@
30330000: 'rfkillrp', 'usbotg1', 'usbotg1-pwr', 'usbotg1-pwr-gpio' do not match any of the regexes: 'grp$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Wed, 24 May 2023 13:10:05 +0000 (10:10 -0300)]
ARM: dts: imx7d-smegw01: Remove unneeded #address-cells/#size-cells
Remove the unneeded #address-cells/#size-cells from sram@0 to fix
the following 'make CHECK_DTBS=y imx7d-smegw01.dtb' warning:
sram@0: Unevaluated properties are not allowed ('#address-cells', '#size-cells' were unexpected)
From schema: Documentation/devicetree/bindings/mtd/microchip,mchp48l640.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 22 May 2023 19:32:19 +0000 (12:32 -0700)]
ARM: dts: imx6qdl-gw5912: remove invalid nodes from fan-controller
Remove the invalid #address-cells and #size-cells nodes from
the fan-controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Mon, 22 May 2023 19:32:18 +0000 (12:32 -0700)]
ARM: dts: imx6qdl-gw54xx: remove invalid nodes from fan-controller
Remove the invalid #address-cells and #size-cells nodes from
the fan-controller.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Tue, 23 May 2023 23:52:32 +0000 (20:52 -0300)]
ARM: dts: imx6sx: Add LDB support
i.MX6SX has an LVDS controller that is connected to the eLCDIF.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>