Eric Dumazet [Tue, 2 Dec 2014 12:30:59 +0000 (04:30 -0800)]
net: mvneta: fix race condition in mvneta_tx()
[ Upstream commit
5f478b41033606d325e420df693162e2524c2b94 ]
mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.
Fixes:
71f6d1b31fb1 ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
willy tarreau [Tue, 2 Dec 2014 07:13:04 +0000 (08:13 +0100)]
net: mvneta: fix Tx interrupt delay
[ Upstream commit
aebea2ba0f7495e1a1c9ea5e753d146cb2f6b845 ]
The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.
The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.
In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.
The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.
Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.
No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.
This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tom Herbert [Sat, 29 Nov 2014 17:59:45 +0000 (09:59 -0800)]
gre: Set inner mac header in gro complete
[ Upstream commit
6fb2a756739aa507c1fd5b8126f0bfc2f070dc46 ]
Set the inner mac header to point to the GRE payload when
doing GRO. This is needed if we proceed to send the packet
through GRE GSO which now uses the inner mac header instead
of inner network header to determine the length of encapsulation
headers.
Fixes:
14051f0452a2 ("gre: Use inner mac length when computing tunnel length")
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Dichtel [Thu, 27 Nov 2014 09:16:15 +0000 (10:16 +0100)]
rtnetlink: release net refcnt on error in do_setlink()
[ Upstream commit
e0ebde0e131b529fd721b24f62872def5ec3718c ]
rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.
CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes:
b51642f6d77b ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jack Morgenstein [Tue, 25 Nov 2014 09:54:31 +0000 (11:54 +0200)]
net/mlx4_core: Limit count field to 24 bits in qp_alloc_res
[ Upstream commit
2d5c57d7fbfaa642fb7f0673df24f32b83d9066c ]
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes:
c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thadeu Lima de Souza Cascardo [Tue, 25 Nov 2014 16:21:11 +0000 (14:21 -0200)]
tg3: fix ring init when there are more TX than RX channels
[ Upstream commit
a620a6bc1c94c22d6c312892be1e0ae171523125 ]
If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.
This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcelo Leitner [Thu, 11 Dec 2014 12:02:22 +0000 (10:02 -0200)]
Fix race condition between vxlan_sock_add and vxlan_sock_release
[ Upstream commit
00c83b01d58068dfeb2e1351cca6fccf2a83fa8f ]
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes:
7c47cedf43a8b3 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yuri Chislov [Mon, 24 Nov 2014 10:25:15 +0000 (11:25 +0100)]
ipv6: gre: fix wrong skb->protocol in WCCP
[ Upstream commit
be6572fdb1bfbe23b2624d477de50af50b02f5d6 ]
When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Fixes:
c12b395a4664 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lucien [Sun, 23 Nov 2014 07:04:11 +0000 (15:04 +0800)]
ip_tunnel: the lack of vti_link_ops' dellink() cause kernel panic
[ Upstream commit
20ea60ca9952bd19d4b0d74719daba305aef5178 ]
Now the vti_link_ops do not point the .dellink, for fb tunnel device
(ip_vti0), the net_device will be removed as the default .dellink is
unregister_netdevice_queue,but the tunnel still in the tunnel list,
then if we add a new vti tunnel, in ip_tunnel_find():
hlist_for_each_entry_rcu(t, head, hash_node) {
if (local == t->parms.iph.saddr &&
remote == t->parms.iph.daddr &&
link == t->parms.link &&
==> type == t->dev->type &&
ip_tunnel_key_match(&t->parms, flags, key))
break;
}
the panic will happen, cause dev of ip_tunnel *t is null:
[ 3835.072977] IP: [<
ffffffffa04103fd>] ip_tunnel_find+0x9d/0xc0 [ip_tunnel]
[ 3835.073008] PGD
b2c21067 PUD
b7277067 PMD 0
[ 3835.073008] Oops: 0000 [#1] SMP
.....
[ 3835.073008] Stack:
[ 3835.073008]
ffff8800b72d77f0 ffffffffa0411924 ffff8800bb956000 ffff8800b72d78e0
[ 3835.073008]
ffff8800b72d78a0 0000000000000000 ffffffffa040d100 ffff8800b72d7858
[ 3835.073008]
ffffffffa040b2e3 0000000000000000 0000000000000000 0000000000000000
[ 3835.073008] Call Trace:
[ 3835.073008] [<
ffffffffa0411924>] ip_tunnel_newlink+0x64/0x160 [ip_tunnel]
[ 3835.073008] [<
ffffffffa040b2e3>] vti_newlink+0x43/0x70 [ip_vti]
[ 3835.073008] [<
ffffffff8150d4da>] rtnl_newlink+0x4fa/0x5f0
[ 3835.073008] [<
ffffffff812f68bb>] ? nla_strlcpy+0x5b/0x70
[ 3835.073008] [<
ffffffff81508fb0>] ? rtnl_link_ops_get+0x40/0x60
[ 3835.073008] [<
ffffffff8150d11f>] ? rtnl_newlink+0x13f/0x5f0
[ 3835.073008] [<
ffffffff81509cf4>] rtnetlink_rcv_msg+0xa4/0x270
[ 3835.073008] [<
ffffffff8126adf5>] ? sock_has_perm+0x75/0x90
[ 3835.073008] [<
ffffffff81509c50>] ? rtnetlink_rcv+0x30/0x30
[ 3835.073008] [<
ffffffff81529e39>] netlink_rcv_skb+0xa9/0xc0
[ 3835.073008] [<
ffffffff81509c48>] rtnetlink_rcv+0x28/0x30
....
modprobe ip_vti
ip link del ip_vti0 type vti
ip link add ip_vti0 type vti
rmmod ip_vti
do that one or more times, kernel will panic.
fix it by assigning ip_tunnel_dellink to vti_link_ops' dellink, in
which we skip the unregister of fb tunnel device. do the same on ip6_vti.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Torokhov [Fri, 14 Nov 2014 21:39:05 +0000 (13:39 -0800)]
sata_fsl: fix error handling of irq_of_parse_and_map
commit
aad0b624129709c94c2e19e583b6053520353fa8 upstream.
irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Thu, 4 Dec 2014 18:13:28 +0000 (13:13 -0500)]
ahci: disable MSI on SAMSUNG 0xa800 SSD
commit
2b21ef0aae65f22f5ba86b13c4588f6f0c2dbefb upstream.
Just like 0x1600 which got blacklisted by
66a7cbc303f4 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled. Disable MSI.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Devin Ryles [Fri, 7 Nov 2014 22:59:05 +0000 (17:59 -0500)]
AHCI: Add DeviceIDs for Sunrise Point-LP SATA controller
commit
249cd0a187ed4ef1d0af7f74362cc2791ec5581b upstream.
This patch adds DeviceIDs for Sunrise Point-LP.
Signed-off-by: Devin Ryles <devin.ryles@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Tue, 18 Nov 2014 09:27:12 +0000 (11:27 +0200)]
USB: xhci: Reset a halted endpoint immediately when we encounter a stall.
commit
8e71a322fdb127814bcba423a512914ca5bc6cf5 upstream.
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sakari Ailus [Thu, 6 Nov 2014 20:49:45 +0000 (17:49 -0300)]
media: smiapp: Only some selection targets are settable
commit
b31eb901c4e5eeef4c83c43dfbc7fe0d4348cb21 upstream.
Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Clayton [Sat, 22 Nov 2014 09:51:10 +0000 (09:51 +0000)]
x86: Use $(OBJDUMP) instead of plain objdump
commit
e2e68ae688b0a3766cd75aedf4ed4e39be402009 upstream.
commit
e6023367d779 'x86, kaslr: Prevent .bss from overlaping initrd'
broke the cross compile of x86. It added a objdump invocation, which
invokes the host native objdump and ignores an active cross tool
chain.
Use $(OBJDUMP) instead which takes the CROSS_COMPILE prefix into
account.
[ tglx: Massage changelog and use $(OBJDUMP) ]
Fixes:
e6023367d779 'x86, kaslr: Prevent .bss from overlaping initrd'
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/54705C8E.1080400@googlemail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Mon, 1 Dec 2014 16:56:54 +0000 (17:56 +0100)]
drm/i915: Unlock panel even when LVDS is disabled
commit
b0616c5306b342ceca07044dbc4f917d95c4f825 upstream.
Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in
commit
c31407a3672aaebb4acddf90944a114fa5c8af7b
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Oct 18 21:07:01 2012 +0100
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Mon, 24 Nov 2014 16:02:45 +0000 (17:02 +0100)]
drm/i915: More cautious with pch fifo underruns
commit
b68362278af94e1171f5be9d4e44988601fb0439 upstream.
Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).
So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.
Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.
References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petr Mladek [Thu, 27 Nov 2014 15:57:21 +0000 (16:57 +0100)]
drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
commit
f5475cc43c899e33098d4db44b7c5e710f16589d upstream.
I was unable too boot 3.18.0-rc6 because of the following kernel
panic in drm_calc_vbltimestamp_from_scanoutpos():
[drm] Initialized drm 1.1.0
20060810
[drm] radeon kernel modesetting enabled.
[drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080).
[drm] register mmio base: 0xC8400000
[drm] register mmio size: 65536
radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used)
radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
[drm] Detected VRAM RAM=128M, BAR=128M
[drm] RAM width 16bits DDR
[TTM] Zone kernel: Available graphics memory: 3829346 kiB
[TTM] Zone dma32: Available graphics memory: 2097152 kiB
[TTM] Initializing pool allocator
[TTM] Initializing DMA pool allocator
[drm] radeon: 16M of VRAM memory ready
[drm] radeon: 512M of GTT memory ready.
[drm] GART: num cpu pages 131072, num gpu pages 131072
[drm] PCI GART of 512M enabled (table at 0x0000000037880000).
radeon 0000:0b:01.0: WB disabled
radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] Driver supports precise vblank timestamp query.
[drm] radeon: irq initialized.
[drm] Loading R100 Microcode
radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2
radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
[drm:r100_cp_init] *ERROR* Failed to load firmware!
radeon 0000:0b:01.0: failed initializing CP (-2).
radeon 0000:0b:01.0: Disabling GPU acceleration
[drm] radeon: cp finalized
BUG: unable to handle kernel NULL pointer dereference at
000000000000025c
IP: [<
ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
PGD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649
Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006
task:
ffff880234da2010 ti:
ffff880234da4000 task.ti:
ffff880234da4000
RIP: 0010:[<
ffffffff8150423b>] [<
ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
RSP: 0000:
ffff880234da7918 EFLAGS:
00010086
RAX:
ffffffff81557890 RBX:
0000000000000000 RCX:
ffff880234da7a48
RDX:
ffff880234da79f4 RSI:
0000000000000000 RDI:
ffff880232e15000
RBP:
ffff880234da79b8 R08:
0000000000000000 R09:
0000000000000000
R10:
000000000000000a R11:
0000000000000001 R12:
ffff880232dda1c0
R13:
ffff880232e1518c R14:
0000000000000292 R15:
ffff880232e15000
FS:
0000000000000000(0000) GS:
ffff88023fc40000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
000000008005003b
CR2:
000000000000025c CR3:
0000000002014000 CR4:
00000000000007e0
Stack:
ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480
ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d
ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58
Call Trace:
[<
ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110
[<
ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60
[<
ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180
[<
ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70
[<
ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0
[<
ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70
[<
ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0
[<
ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70
[<
ffffffff8156c07e>] r100_init+0x26e/0x410
[<
ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50
[<
ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210
[<
ffffffff81506965>] drm_dev_register+0xb5/0x110
[<
ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200
[<
ffffffff815291cd>] radeon_pci_probe+0xad/0xe0
[<
ffffffff8141a365>] local_pci_probe+0x45/0xa0
[<
ffffffff8141b741>] pci_device_probe+0xd1/0x130
[<
ffffffff81633dad>] driver_probe_device+0x12d/0x3e0
[<
ffffffff8163413b>] __driver_attach+0x9b/0xa0
[<
ffffffff816340a0>] ? __device_attach+0x40/0x40
[<
ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0
[<
ffffffff8163378e>] driver_attach+0x1e/0x20
[<
ffffffff81633390>] bus_add_driver+0x180/0x240
[<
ffffffff81634914>] driver_register+0x64/0xf0
[<
ffffffff81419cac>] __pci_register_driver+0x4c/0x50
[<
ffffffff81509bf5>] drm_pci_init+0xf5/0x120
[<
ffffffff821dc871>] ? ttm_init+0x6a/0x6a
[<
ffffffff821dc908>] radeon_init+0x97/0xb5
[<
ffffffff810002fc>] do_one_initcall+0xbc/0x1f0
[<
ffffffff810e3278>] ? __wake_up+0x48/0x60
[<
ffffffff8218e256>] kernel_init_freeable+0x18a/0x215
[<
ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0
[<
ffffffff818a78f0>] ? rest_init+0x80/0x80
[<
ffffffff818a78fe>] kernel_init+0xe/0xf0
[<
ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0
[<
ffffffff818a78f0>] ? rest_init+0x80/0x80
Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60
RIP [<
ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
RSP <
ffff880234da7918>
CR2:
000000000000025c
---[ end trace
ad2c0aadf48e2032 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html
I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Tested-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grygorii Strashko [Mon, 1 Dec 2014 15:34:04 +0000 (17:34 +0200)]
i2c: davinci: generate STP always when NACK is received
commit
9ea359f7314132cbcb5a502d2d8ef095be1f45e4 upstream.
According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]
Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).
For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:
S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->
The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.
Hence, fix it by generating Stop condition (STP) always when NACK is received.
This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit
cda2109a26eb ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Kochetkov [Fri, 21 Nov 2014 00:16:51 +0000 (04:16 +0400)]
i2c: omap: fix i207 errata handling
commit
ccfc866356674cb3a61829d239c685af6e85f197 upstream.
commit
6d9939f651419a63e091105663821f9c7d3fec37 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled.
6d9939f6514 code doesn't correspond to workaround provided by
errata.
According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.
Restored pre
6d9939f6514 way of handling errata.
Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes:
6d9939f651419a63e09110 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Kochetkov [Tue, 18 Nov 2014 17:00:58 +0000 (21:00 +0400)]
i2c: omap: fix NACK and Arbitration Lost irq handling
commit
27caca9d2e01c92b26d0690f065aad093fea01c7 upstream.
commit
1d7afc95946487945cc7f5019b41255b72224b70 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).
A didn't see real impacts of the 1d7afc9, but it is really bad idea to
have ISR running on user data after transfer was complete.
It looks, what 1d7afc9 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).
According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).
All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...
The patch restore pre 1d7afc9 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.
Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK
In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc9 i2c: omap: ack IRQ in parts
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Seth Forshee [Wed, 26 Nov 2014 02:28:24 +0000 (20:28 -0600)]
xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
commit
8d609725d4357f499e2103e46011308b32f53513 upstream.
These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.
Fixes:
f36c374782e4 ("xen/netfront: handle compound page fragments on transmit")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Forrest [Tue, 2 Dec 2014 23:59:42 +0000 (15:59 -0800)]
mm: fix anon_vma_clone() error treatment
commit
c4ea95d7cd08d9ffd7fa75e6c5e0332d596dd11e upstream.
Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).
I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost. In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten. So a failure of anon_vma_clone() will return
success since err at this point is now zero.
Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.
Fixes:
ef0855d334e1 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()")
Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tim Hartrick <tim@edgecast.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hugh Dickins [Tue, 2 Dec 2014 23:59:39 +0000 (15:59 -0800)]
mm: fix swapoff hang after page migration and fork
commit
2022b4d18a491a578218ce7a4eca8666db895a73 upstream.
I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.
I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.
Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so. Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.
There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Morton [Tue, 2 Dec 2014 23:59:28 +0000 (15:59 -0800)]
mm/vmpressure.c: fix race in vmpressure_work_fn()
commit
91b57191cfd152c02ded0745250167d0263084f8 upstream.
In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051
[akpm@linux-foundation.org: neaten]
Reported-by: ji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Weijie Yang [Tue, 2 Dec 2014 23:59:25 +0000 (15:59 -0800)]
mm: frontswap: invalidate expired data on a dup-store failure
commit
fb993fa1a2f669215fa03a09eed7848f2663e336 upstream.
If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
1. use zswap as the frontswap backend with writeback feature
2. store a swap page(version_1) to entry A, success
3. dup-store a newer page(version_2) to the same entry A, fail
4. use __swap_writepage() write version_2 page to swapfile, success
5. zswap do shrink, writeback version_1 page to swapfile
6. version_2 page is overwrited by version_1, data corrupt.
This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 6 Dec 2014 23:56:06 +0000 (15:56 -0800)]
Linux 3.14.26
David Jeffery [Tue, 5 Aug 2014 15:19:42 +0000 (11:19 -0400)]
nfs: Don't busy-wait on SIGKILL in __nfs_iocounter_wait
commit
92a56555bd576c61b27a5cab9f38a33a1e9a1df5 upstream.
If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait,
it will busy-wait or soft lockup in its while loop.
nfs_wait_bit_killable won't sleep, and the loop won't exit on
the error return.
Stop the busy-wait by breaking out of the loop when
nfs_wait_bit_killable returns an error.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[ kamal: backport to 3.13-stable: context ]
Cc: Moritz Mühlenhoff <muehlenhoff@univention.de>
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Mon, 22 Sep 2014 11:17:48 +0000 (13:17 +0200)]
x86: kvm: use alternatives for VMCALL vs. VMMCALL if kernel text is read-only
commit
c1118b3602c2329671ad5ec8bdf8e374323d6343 upstream.
On x86_64, kernel text mappings are mapped read-only with CONFIG_DEBUG_RODATA.
In that case, KVM will fail to patch VMCALL instructions to VMMCALL
as required on AMD processors.
The failure mode is currently a divide-by-zero exception, which obviously
is a KVM bug that has to be fixed. However, picking the right instruction
between VMCALL and VMMCALL will be faster and will help if you cannot upgrade
the hypervisor.
Reported-by: Chris Webb <chris@arachsys.com>
Tested-by: Chris Webb <chris@arachsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cong Wang [Thu, 22 May 2014 18:57:17 +0000 (11:57 -0700)]
batman: fix a bogus warning from batadv_is_on_batman_iface()
commit
b6ed5498601df40489606dbc14a9c7011c16630b upstream.
batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Antonio Quartulli <antonio@open-mesh.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Herrenschmidt [Tue, 7 Oct 2014 05:12:36 +0000 (16:12 +1100)]
powerpc/powernv: Honor the generic "no_64bit_msi" flag
commit
360743814c4082515581aa23ab1d8e699e1fbe88 upstream.
Instead of the arch specific quirk which we are deprecating
and that drivers don't understand.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Layton [Mon, 3 Feb 2014 17:13:07 +0000 (12:13 -0500)]
locks: eliminate BUG() call when there's an unexpected lock on file close
commit
8c3cac5e6a85f03602ffe09c44f14418699e31ec upstream.
A leftover lock on the list is surely a sign of a problem of some sort,
but it's not necessarily a reason to panic the box. Instead, just log a
warning with some info about the lock, and then delete it like we would
any other lock.
In the event that the filesystem declares a ->lock f_op, we may end up
leaking something, but that's generally preferable to an immediate
panic.
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Markus Blank-Burian <burian@muenster.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxime COQUELIN [Thu, 6 Nov 2014 09:54:19 +0000 (10:54 +0100)]
bitops: Fix shift overflow in GENMASK macros
commit
00b4d9a14125f1e51874def2b9de6092e007412d upstream.
On some 32 bits architectures, including x86, GENMASK(31, 0) returns 0
instead of the expected ~0UL.
This is the same on some 64 bits architectures with GENMASK_ULL(63, 0).
This is due to an overflow in the shift operand, 1 << 32 for GENMASK,
1 << 64 for GENMASK_ULL.
Reported-by: Eric Paire <eric.paire@st.com>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux@rasmusvillemoes.dk
Cc: gong.chen@linux.intel.com
Cc: John Sullivan <jsrhbz@kanargh.force9.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Fixes:
10ef6b0dffe4 ("bitops: Introduce a more generic BITMASK macro")
Link: http://lkml.kernel.org/r/1415267659-10563-1-git-send-email-maxime.coquelin@st.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Herrenschmidt [Fri, 3 Oct 2014 05:18:59 +0000 (15:18 +1000)]
gpu/radeon: Set flag to indicate broken 64-bit MSI
commit
91ed6fd2c383bb8f02d66e98b4a4d2f7207249dc upstream.
Some radeon ASICs don't support all 64 address bits of MSIs despite
advertising support for 64-bit MSIs in their configuration space.
This breaks on systems such as IBM POWER7/8, where 64-bit MSIs can
be assigned with some of the high address bits set.
This makes use of the newly introduced "no_64bit_msi" flag in structure
pci_dev to allow the MSI allocation code to fallback to 32-bit MSIs
on those adapters.
Adding Alex's review tag. Patch to the driver is identical to the
reviewed one, I dropped the arch/powerpc hunk rewrote the subject
and cset comment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Thu, 13 Nov 2014 00:17:02 +0000 (19:17 -0500)]
drm/radeon: fix endian swapping in vbios fetch for tdp table
commit
28731d5818ae25b92d1fb82fe0ac196e97102c1b upstream.
Value needs to be swapped on BE.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maurizio Lombardi [Thu, 20 Nov 2014 10:17:33 +0000 (11:17 +0100)]
bnx2fc: do not add shared skbs to the fcoe_rx_list
commit
01a4cc4d0cd6a836c7b923760e8eb1cbb6a47258 upstream.
In some cases, the fcoe_rx_list may contains multiple instances
of the same skb (the so called "shared skbs").
the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list,
modifies (and destroys) its content and then proceed to the next one.
The problem is that if the skb is shared, the remaining instances will
be corrupted.
The solution is to use skb_share_check() before adding the skb to the
fcoe_rx_list.
[ 6286.808725] ------------[ cut here ]------------
[ 6286.808729] WARNING: at include/scsi/fc_frame.h:173 bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]()
[ 6286.808748] Modules linked in: bnx2x(-) mdio dm_service_time bnx2fc cnic uio fcoe libfcoe 8021q garp stp mrp libfc llc scsi_transport_fc scsi_tgt sg iTCO_wdt iTCO_vendor_support coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel e1000e ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper ptp cryptd hpilo serio_raw hpwdt lpc_ich pps_core ipmi_si pcspkr mfd_core ipmi_msghandler shpchp pcc_cpufreq mperf nfsd auth_rpcgss nfs_acl lockd sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit ata_piix drm_kms_helper ttm drm libata i2c_core hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mdio]
[ 6286.808750] CPU: 3 PID: 1304 Comm: bnx2fc_l2_threa Not tainted 3.10.0-121.el7.x86_64 #1
[ 6286.808750] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013
[ 6286.808752]
0000000000000000 000000000b36e715 ffff8800deba1e00 ffffffff815ec0ba
[ 6286.808753]
ffff8800deba1e38 ffffffff8105dee1 ffffffffa05618c0 ffff8801e4c81888
[ 6286.808754]
ffffe8ffff663868 ffff8801f402b180 ffff8801f56bc000 ffff8800deba1e48
[ 6286.808754] Call Trace:
[ 6286.808759] [<
ffffffff815ec0ba>] dump_stack+0x19/0x1b
[ 6286.808762] [<
ffffffff8105dee1>] warn_slowpath_common+0x61/0x80
[ 6286.808763] [<
ffffffff8105e00a>] warn_slowpath_null+0x1a/0x20
[ 6286.808765] [<
ffffffffa054f415>] bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]
[ 6286.808767] [<
ffffffffa054eff0>] ? bnx2fc_disable+0x90/0x90 [bnx2fc]
[ 6286.808769] [<
ffffffff81085aef>] kthread+0xcf/0xe0
[ 6286.808770] [<
ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140
[ 6286.808772] [<
ffffffff815fc76c>] ret_from_fork+0x7c/0xb0
[ 6286.808773] [<
ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140
[ 6286.808774] ---[ end trace
c6cdb939184ccb4e ]---
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jane Zhou [Mon, 24 Nov 2014 19:44:08 +0000 (11:44 -0800)]
net/ping: handle protocol mismatching scenario
commit
91a0b603469069cdcce4d572b7525ffc9fd352a6 upstream.
ping_lookup() may return a wrong sock if sk_buff's and sock's protocols
dont' match. For example, sk_buff's protocol is ETH_P_IPV6, but sock's
sk_family is AF_INET, in that case, if sk->sk_bound_dev_if is zero, a wrong
sock will be returned.
the fix is to "continue" the searching, if no matching, return NULL.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Jane Zhou <a17711@motorola.com>
Signed-off-by: Yiwei Zhao <gbjc64@motorola.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Layton [Thu, 5 Jun 2014 13:45:00 +0000 (09:45 -0400)]
nfsd: don't halt scanning the DRC LRU list when there's an RC_INPROG entry
commit
1b19453d1c6abcfa7c312ba6c9f11a277568fc94 upstream.
Currently, the DRC cache pruner will stop scanning the list when it
hits an entry that is RC_INPROG. It's possible however for a call to
take a *very* long time. In that case, we don't want it to block other
entries from being pruned if they are expired or we need to trim the
cache to get back under the limit.
Fix the DRC cache pruner to just ignore RC_INPROG entries.
Signed-off-by: Jeff Layton <jlayton@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Cc: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Wed, 19 Nov 2014 17:47:50 +0000 (12:47 -0500)]
nfsd: Fix slot wake up race in the nfsv4.1 callback code
commit
c6c15e1ed303ffc47e696ea1c9a9df1761c1f603 upstream.
The currect code for nfsd41_cb_get_slot() and nfsd4_cb_done() has no
locking in order to guarantee atomicity, and so allows for races of
the form.
Task 1 Task 2
====== ======
if (test_and_set_bit(0) != 0) {
clear_bit(0)
rpc_wake_up_next(queue)
rpc_sleep_on(queue)
return false;
}
This patch breaks the race condition by adding a retest of the bit
after the call to rpc_sleep_on().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Hellwig [Sat, 8 Nov 2014 12:11:03 +0000 (13:11 +0100)]
nfsd: correctly define v4.2 support attributes
commit
6d0ba0432a5e10bc714ba9c5adc460e726e5fbb4 upstream.
Even when security labels are disabled we support at least the same
attributes as v4.1.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stanislaw Gruszka [Tue, 11 Nov 2014 13:28:47 +0000 (14:28 +0100)]
rt2x00: do not align payload on modern H/W
commit
cfd9167af14eb4ec21517a32911d460083ee3d59 upstream.
RT2800 and newer hardware require padding between header and payload if
header length is not multiple of 4.
For historical reasons we also align payload to to 4 bytes boundary, but
such alignment is not needed on modern H/W.
Patch fixes skb_under_panic problems reported from time to time:
https://bugzilla.kernel.org/show_bug.cgi?id=84911
https://bugzilla.kernel.org/show_bug.cgi?id=72471
http://marc.info/?l=linux-wireless&m=
139108549530402&w=2
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi>
Debugged-by: Antti S. Lankila <alankila@bel.fi>
Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Körper [Fri, 31 Oct 2014 06:33:54 +0000 (07:33 +0100)]
can: dev: avoid calling kfree_skb() from interrupt context
commit
5247a589c24022ab34e780039cc8000c48f2035e upstream.
ikfree_skb() is Called in can_free_echo_skb(), which might be called from (TX
Error) interrupt, which triggers the folloing warning:
[ 1153.360705] ------------[ cut here ]------------
[ 1153.360715] WARNING: CPU: 0 PID: 31 at net/core/skbuff.c:563 skb_release_head_state+0xb9/0xd0()
[ 1153.360772] Call Trace:
[ 1153.360778] [<
c167906f>] dump_stack+0x41/0x52
[ 1153.360782] [<
c105bb7e>] warn_slowpath_common+0x7e/0xa0
[ 1153.360784] [<
c158b909>] ? skb_release_head_state+0xb9/0xd0
[ 1153.360786] [<
c158b909>] ? skb_release_head_state+0xb9/0xd0
[ 1153.360788] [<
c105bc42>] warn_slowpath_null+0x22/0x30
[ 1153.360791] [<
c158b909>] skb_release_head_state+0xb9/0xd0
[ 1153.360793] [<
c158be90>] skb_release_all+0x10/0x30
[ 1153.360795] [<
c158bf06>] kfree_skb+0x36/0x80
[ 1153.360799] [<
f8486938>] ? can_free_echo_skb+0x28/0x40 [can_dev]
[ 1153.360802] [<
f8486938>] can_free_echo_skb+0x28/0x40 [can_dev]
[ 1153.360805] [<
f849a12c>] esd_pci402_interrupt+0x34c/0x57a [esd402]
[ 1153.360809] [<
c10a75b5>] handle_irq_event_percpu+0x35/0x180
[ 1153.360811] [<
c10a7623>] ? handle_irq_event_percpu+0xa3/0x180
[ 1153.360813] [<
c10a7731>] handle_irq_event+0x31/0x50
[ 1153.360816] [<
c10a9c7f>] handle_fasteoi_irq+0x6f/0x120
[ 1153.360818] [<
c10a9c10>] ? handle_edge_irq+0x110/0x110
[ 1153.360822] [<
c1011b61>] handle_irq+0x71/0x90
[ 1153.360823] <IRQ> [<
c168152c>] do_IRQ+0x3c/0xd0
[ 1153.360829] [<
c1680b6c>] common_interrupt+0x2c/0x34
[ 1153.360834] [<
c107d277>] ? finish_task_switch+0x47/0xf0
[ 1153.360836] [<
c167c27b>] __schedule+0x35b/0x7e0
[ 1153.360839] [<
c10a5334>] ? console_unlock+0x2c4/0x4d0
[ 1153.360842] [<
c13df500>] ? n_tty_receive_buf_common+0x890/0x890
[ 1153.360845] [<
c10707b6>] ? process_one_work+0x196/0x370
[ 1153.360847] [<
c167c723>] schedule+0x23/0x60
[ 1153.360849] [<
c1070de1>] worker_thread+0x161/0x460
[ 1153.360852] [<
c1090fcf>] ? __wake_up_locked+0x1f/0x30
[ 1153.360854] [<
c1070c80>] ? rescuer_thread+0x2f0/0x2f0
[ 1153.360856] [<
c1074f01>] kthread+0xa1/0xc0
[ 1153.360859] [<
c1680401>] ret_from_kernel_thread+0x21/0x30
[ 1153.360861] [<
c1074e60>] ? kthread_create_on_node+0x110/0x110
[ 1153.360863] ---[ end trace
5ff83639cbb74b35 ]---
This patch replaces the kfree_skb() by dev_kfree_skb_any().
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Sünkenberg [Tue, 18 Nov 2014 19:23:32 +0000 (20:23 +0100)]
scsi: add Intel Multi-Flex to scsi scan blacklist
commit
1899045510ff109980d9cc34e330fd8ca3631871 upstream.
Intel Multi-Flex LUNs choke on REPORT SUPPORTED OPERATION CODES
resulting in sd_mod hanging for several minutes on startup.
The issue was introduced with WRITE SAME discovery heuristics.
Fixes:
5db44863b6eb ("[SCSI] sd: Implement support for WRITE SAME")
Signed-off-by: Christian Sünkenberg <christian.suenkenberg@hfg-karlsruhe.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Bellinger [Wed, 8 Oct 2014 06:19:20 +0000 (06:19 +0000)]
vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
commit
ab8edab132829b26dd13db6caca3c242cce35dc1 upstream.
This patch addresses a bug where individual vhost-scsi configfs endpoint
groups can be removed from below while active exports to QEMU userspace
still exist, resulting in an OOPs.
It adds a configfs_depend_item() in vhost_scsi_set_endpoint() to obtain
an explicit dependency on se_tpg->tpg_group in order to prevent individual
vhost-scsi WWPN endpoints from being released via normal configfs methods
while an QEMU ioctl reference still exists.
Also, add matching configfs_undepend_item() in vhost_scsi_clear_endpoint()
to release the dependency, once QEMU's reference to the individual group
at /sys/kernel/config/target/vhost/$WWPN/$TPGT is released.
(Fix up vhost_scsi_clear_endpoint() error path - DanC)
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thor Thayer [Thu, 6 Nov 2014 19:54:27 +0000 (13:54 -0600)]
spi: dw: Fix dynamic speed change.
commit
0a8727e69778683495058852f783eeda141a754e upstream.
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Vlastimil Setka <setka@vsis.cz>
Signed-off-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicholas Bellinger [Sun, 5 Oct 2014 09:13:03 +0000 (02:13 -0700)]
iser-target: Disable TX completion interrupt coalescing
commit
0d0f660d882c1c02748ced13966a2413aa5d6cc2 upstream.
This patch explicitly disables TX completion interrupt coalescing logic
in isert_put_response() and isert_put_datain() that was originally added
as an efficiency optimization in commit
95b60f07.
It has been reported that this change can trigger ABORT_TASK timeouts
under certain small block workloads, where disabling coalescing was
required for stability. According to Sagi, this doesn't impact
overall performance, so go ahead and disable it for now.
Reported-by: Moussa Ba <moussaba@micron.com>
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sagi Grimberg [Tue, 10 Jun 2014 10:41:41 +0000 (13:41 +0300)]
Target/iser: Fix a wrong dereference in case discovery session is over iser
commit
e0546fc1ba66c90cb38a5764357366267d3e58e4 upstream.
In case the discovery session is carried over iser, we can't
access the assumed network portal since the default portal is
used. In this case we don't really need to allocate the fastreg
pool, just prepare to the text pdu that will follow.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sagi Grimberg [Tue, 28 Oct 2014 20:45:03 +0000 (13:45 -0700)]
iser-target: Handle DEVICE_REMOVAL event on network portal listener correctly
commit
3b726ae2de02a406cc91903f80132daee37b6f1b upstream.
In this case the cm_id->context is the isert_np, and the cm_id->qp
is NULL, so use that to distinct the cases.
Since we don't expect any other events on this cm_id we can
just return -1 for explicit termination of the cm_id by the
cma layer.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Dreier [Tue, 14 Oct 2014 21:16:24 +0000 (14:16 -0700)]
target: Don't call TFO->write_pending if data_length == 0
commit
885e7b0e181c14e4d0ddd26c688bad2b84c1ada9 upstream.
If an initiator sends a zero-length command (e.g. TEST UNIT READY) but
sets the transfer direction in the transport layer to indicate a
data-out phase, we still shouldn't try to transfer data. At best it's
a NOP, and depending on the transport, we might crash on an
uninitialized sg list.
Reported-by: Craig Watson <craig.watson@vanguard-rugged.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bart Van Assche [Sun, 19 Oct 2014 15:05:33 +0000 (18:05 +0300)]
srp-target: Retry when QP creation fails with ENOMEM
commit
ab477c1ff5e0a744c072404bf7db51bfe1f05b6e upstream.
It is not guaranteed to that srp_sq_size is supported
by the HCA. So if we failed to create the QP with ENOMEM,
try with a smaller srp_sq_size. Keep it up until we hit
MIN_SRPT_SQ_SIZE, then fail the connection.
Reported-by: Mark Lehrer <lehrer@gmail.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Tue, 25 Nov 2014 08:38:17 +0000 (00:38 -0800)]
Input: xpad - use proper endpoint type
commit
a1f9a4072655843fc03186acbad65990cc05dd2d upstream.
The xpad wireless endpoint is not a bulk endpoint on my devices, but
rather an interrupt one, so the USB core complains when it is submitted.
I'm guessing that the author really did mean that this should be an
interrupt urb, but as there are a zillion different xpad devices out
there, let's cover out bases and handle both bulk and interrupt
endpoints just as easily.
Signed-off-by: "Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Sagal [Mon, 17 Nov 2014 01:23:40 +0000 (17:23 -0800)]
Input: synaptics - adjust min/max on Thinkpad E540
commit
bce4f9e764c36bc35dd5c9cf9e057c09f422397d upstream.
The LEN2006 Synaptics touchpad (as found in Thinkpad E540) returns wrong
min max values.
touchpad-edge-detector output:
> Touchpad SynPS/2 Synaptics TouchPad on /dev/input/event6
> Move one finger around the touchpad to detect the actual edges
> Kernel says: x [1472..5674], y [1408..4684]
> Touchpad sends: x [1264..5675], y [1171..4688]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88211
Signed-off-by: Binyamin Sagal <bensagal@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vladimir Murzin [Thu, 27 Nov 2014 10:39:04 +0000 (11:39 +0100)]
ARM: 8226/1: cacheflush: get rid of restarting block
commit
3f4aa45ceea5789a4aade536acc27f2e0d3da5e1 upstream.
We cannot restart cacheflush safely if a process provides user-defined
signal handler and signal is pending. In this case -EINTR is returned
and it is expected that process re-invokes syscall. However, there are
a few problems with that:
* looks like nobody bothers checking return value from cacheflush
* but if it did, we don't provide the restart address for that, so the
process has to use the same range again
* ...and again, what might lead to looping forever
So, remove cacheflush restarting code and terminate cache flushing
as early as fatal signal is pending.
Reported-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Petazzoni [Tue, 25 Nov 2014 17:43:15 +0000 (18:43 +0100)]
ARM: 8222/1: mvebu: enable strex backoff delay
commit
995ab5189d1d7264e79e665dfa032a19b3ac646e upstream.
Under extremely rare conditions, in an MPCore node consisting of at
least 3 CPUs, two CPUs trying to perform a STREX to data on the same
shared cache line can enter a livelock situation.
This patch enables the HW mechanism that overcomes the bug. This fixes
the incorrect setup of the STREX backoff delay bit due to a wrong
description in the specification.
Note that enabling the STREX backoff delay mechanism is done by
leaving the bit *cleared*, while the bit was currently being set by
the proc-v7.S code.
[Thomas: adapt to latest mainline, slightly reword the commit log, add
stable markers.]
Fixes:
de4901933f6d ("arm: mm: Add support for PJ4B cpu and init routines")
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Eremin-Solenikov [Fri, 21 Nov 2014 14:29:00 +0000 (15:29 +0100)]
ARM: 8216/1: xscale: correct auxiliary register in suspend/resume
commit
ef59a20ba375aeb97b3150a118318884743452a8 upstream.
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn Helgaas [Sat, 1 Nov 2014 23:35:31 +0000 (17:35 -0600)]
of/irq: Drop obsolete 'interrupts' vs 'interrupts-extended' text
commit
66865de4314caca30598244b86817e774c188afa upstream.
a9ecdc0fdc54 ("of/irq: Fix lookup to use 'interrupts-extended' property
first") updated the description to say that:
- Both 'interrupts' and 'interrupts-extended' may be present
- Software should prefer 'interrupts-extended'
- Software that doesn't comprehend 'interrupts-extended' may use
'interrupts'
But there is still a paragraph at the end that prohibits having both and
says 'interrupts' should be preferred.
Remove the contradictory text.
Fixes:
a9ecdc0fdc54 ("of/irq: Fix lookup to use 'interrupts-extended' property first")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gu Zheng [Thu, 6 Nov 2014 09:46:21 +0000 (17:46 +0800)]
aio: fix uncorrent dirty pages accouting when truncating AIO ring buffer
commit
835f252c6debd204fcd607c79975089b1ecd3472 upstream.
https://bugzilla.kernel.org/show_bug.cgi?id=86831
Markus reported that when shutting down mysqld (with AIO support,
on a ext3 formatted Harddrive) leads to a negative number of dirty pages
(underrun to the counter). The negative number results in a drastic reduction
of the write performance because the page cache is not used, because the kernel
thinks it is still 2 ^ 32 dirty pages open.
Add a warn trace in __dec_zone_state will catch this easily:
static inline void __dec_zone_state(struct zone *zone, enum
zone_stat_item item)
{
atomic_long_dec(&zone->vm_stat[item]);
+ WARN_ON_ONCE(item == NR_FILE_DIRTY &&
atomic_long_read(&zone->vm_stat[item]) < 0);
atomic_long_dec(&vm_stat[item]);
}
[ 21.341632] ------------[ cut here ]------------
[ 21.346294] WARNING: CPU: 0 PID: 309 at include/linux/vmstat.h:242
cancel_dirty_page+0x164/0x224()
[ 21.355296] Modules linked in: wutbox_cp sata_mv
[ 21.359968] CPU: 0 PID: 309 Comm: kworker/0:1 Not tainted 3.14.21-WuT #80
[ 21.366793] Workqueue: events free_ioctx
[ 21.370760] [<
c0016a64>] (unwind_backtrace) from [<
c0012f88>]
(show_stack+0x20/0x24)
[ 21.378562] [<
c0012f88>] (show_stack) from [<
c03f8ccc>]
(dump_stack+0x24/0x28)
[ 21.385840] [<
c03f8ccc>] (dump_stack) from [<
c0023ae4>]
(warn_slowpath_common+0x84/0x9c)
[ 21.393976] [<
c0023ae4>] (warn_slowpath_common) from [<
c0023bb8>]
(warn_slowpath_null+0x2c/0x34)
[ 21.402800] [<
c0023bb8>] (warn_slowpath_null) from [<
c00c0688>]
(cancel_dirty_page+0x164/0x224)
[ 21.411524] [<
c00c0688>] (cancel_dirty_page) from [<
c00c080c>]
(truncate_inode_page+0x8c/0x158)
[ 21.420272] [<
c00c080c>] (truncate_inode_page) from [<
c00c0a94>]
(truncate_inode_pages_range+0x11c/0x53c)
[ 21.429890] [<
c00c0a94>] (truncate_inode_pages_range) from
[<
c00c0f6c>] (truncate_pagecache+0x88/0xac)
[ 21.439252] [<
c00c0f6c>] (truncate_pagecache) from [<
c00c0fec>]
(truncate_setsize+0x5c/0x74)
[ 21.447731] [<
c00c0fec>] (truncate_setsize) from [<
c013b3a8>]
(put_aio_ring_file.isra.14+0x34/0x90)
[ 21.456826] [<
c013b3a8>] (put_aio_ring_file.isra.14) from
[<
c013b424>] (aio_free_ring+0x20/0xcc)
[ 21.465660] [<
c013b424>] (aio_free_ring) from [<
c013b4f4>]
(free_ioctx+0x24/0x44)
[ 21.473190] [<
c013b4f4>] (free_ioctx) from [<
c003d8d8>]
(process_one_work+0x134/0x47c)
[ 21.481132] [<
c003d8d8>] (process_one_work) from [<
c003e988>]
(worker_thread+0x130/0x414)
[ 21.489350] [<
c003e988>] (worker_thread) from [<
c00448ac>]
(kthread+0xd4/0xec)
[ 21.496621] [<
c00448ac>] (kthread) from [<
c000ec18>]
(ret_from_fork+0x14/0x20)
[ 21.503884] ---[ end trace
79c4bf42c038c9a1 ]---
The cause is that we set the aio ring file pages as *DIRTY* via SetPageDirty
(bypasses the VFS dirty pages increment) when init, and aio fs uses
*default_backing_dev_info* as the backing dev, which does not disable
the dirty pages accounting capability.
So truncating aio ring file will contribute to accounting dirty pages (VFS
dirty pages decrement), then error occurs.
The original goal is keeping these pages in memory (can not be reclaimed
or swapped) in life-time via marking it dirty. But thinking more, we have
already pinned pages via elevating the page's refcount, which can already
achieve the goal, so the SetPageDirty seems unnecessary.
In order to fix the issue, using the __set_page_dirty_no_writeback instead
of the nop .set_page_dirty, and dropped the SetPageDirty (don't manually
set the dirty flags, don't disable set_page_dirty(), rely on default behaviour).
With the above change, the dirty pages accounting can work well. But as we
known, aio fs is an anonymous one, which should never cause any real write-back,
we can ignore the dirty pages (write back) accounting by disabling the dirty
pages (write back) accounting capability. So we introduce an aio private
backing dev info (disabled the ACCT_DIRTY/WRITEBACK/ACCT_WB capabilities) to
replace the default one.
Reported-by: Markus Königshaus <m.koenigshaus@wut.de>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jurgen Kramer [Sat, 15 Nov 2014 13:01:21 +0000 (14:01 +0100)]
ALSA: usb-audio: Add ctrl message delay quirk for Marantz/Denon devices
commit
6e84a8d7ac3ba246ef44e313e92bc16a1da1b04a upstream.
This patch adds a USB control message delay quirk for a few specific Marantz/Denon
devices. Without the delay the DACs will not work properly and produces the
following type of messages:
Nov 15 10:09:21 orwell kernel: [ 91.342880] usb 3-13: clock source 41 is not valid, cannot use
Nov 15 10:09:21 orwell kernel: [ 91.343775] usb 3-13: clock source 41 is not valid, cannot use
There are likely other Marantz/Denon devices using the same USB module which exhibit the
same problems. But as this cannot be verified I limited the patch to the devices
I could test.
The following two devices are covered by this path:
- Marantz SA-14S1
- Marantz HD-DAC1
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Khoroshilov [Fri, 10 Oct 2014 20:31:07 +0000 (00:31 +0400)]
can: esd_usb2: fix memory leak on disconnect
commit
efbd50d2f62fc1f69a3dcd153e63ba28cc8eb27f upstream.
It seems struct esd_usb2 dev is not deallocated on disconnect. The patch adds
the missing deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lu Baolu [Tue, 18 Nov 2014 09:27:14 +0000 (11:27 +0200)]
usb: xhci: rework root port wake bits if controller isn't allowed to wakeup
commit
a1377e5397ab321e21b793ec8cd2b6f12bd3c718 upstream.
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit
ff8cbf250b44 ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Tue, 18 Nov 2014 09:27:11 +0000 (11:27 +0200)]
USB: xhci: don't start a halted endpoint before its new dequeue is set
commit
c3492dbfa1050debf23a5b5cd2bc7514c5b37896 upstream.
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.)
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Mon, 24 Nov 2014 10:22:38 +0000 (11:22 +0100)]
usb-quirks: Add reset-resume quirk for MS Wireless Laser Mouse 6000
commit
263e80b43559a6103e178a9176938ce171b23872 upstream.
This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Troy Clark [Mon, 17 Nov 2014 22:33:17 +0000 (14:33 -0800)]
usb: serial: ftdi_sio: add PIDs for Matrix Orbital products
commit
204ec6e07ea7aff863df0f7c53301f9cbbfbb9d3 upstream.
Add PIDs for new Matrix Orbital GTT series products.
Signed-off-by: Troy Clark <tclark@matrixorbital.ca>
[johan: shorten commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Preston Fick [Sat, 8 Nov 2014 05:26:11 +0000 (23:26 -0600)]
USB: serial: cp210x: add IDs for CEL MeshConnect USB Stick
commit
ffcfe30ebd8dd703d0fc4324ffe56ea21f5479f4 upstream.
Signed-off-by: Preston Fick <pffick@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 18 Nov 2014 10:25:19 +0000 (11:25 +0100)]
USB: keyspan: fix tty line-status reporting
commit
5d1678a33c731b56e245e888fdae5e88efce0997 upstream.
Fix handling of TTY error flags, which are not bitmasks and must
specifically not be ORed together as this prevents the line discipline
from recognising them.
Also insert null characters when reporting overrun errors as these are
not associated with the received character.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 18 Nov 2014 10:25:20 +0000 (11:25 +0100)]
USB: keyspan: fix overrun-error reporting
commit
855515a6d3731242d85850a206f2ec084c917338 upstream.
Fix reporting of overrun errors, which are not associated with a
character. Instead insert a null character and report only once.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Tue, 18 Nov 2014 10:25:21 +0000 (11:25 +0100)]
USB: ssu100: fix overrun-error reporting
commit
75bcbf29c284dd0154c3e895a0bd1ef0e796160e upstream.
Fix reporting of overrun errors, which should only be reported once
using the inserted null character.
Fixes:
6b8f1ca5581b ("USB: ssu100: set tty_flags in ssu100_process_packet")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Thu, 27 Nov 2014 16:10:21 +0000 (10:10 -0600)]
staging: r8188eu: Add new device ID for DLink GO-USB-N150
commit
6d4556fc0309608f760f1d329df56d77fdd0c31a upstream.
The DLink GO-USB-N150 with revision B1 uses this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cristina Ciocan [Tue, 11 Nov 2014 14:07:42 +0000 (16:07 +0200)]
iio: Fix IIO_EVENT_CODE_EXTRACT_DIR bit mask
commit
ccf54555da9a5e91e454b909ca6a5303c7d6b910 upstream.
The direction field is set on 7 bits, thus we need to AND it with 0111 111 mask
in order to retrieve it, that is 0x7F, not 0xCF as it is now.
Fixes:
ade7ef7ba (staging:iio: Differential channel handling)
Signed-off-by: Cristina Ciocan <cristina.ciocan@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Dufour [Mon, 24 Nov 2014 14:07:53 +0000 (15:07 +0100)]
powerpc/pseries: Fix endiannes issue in RTAS call from xmon
commit
3b8a3c01096925a824ed3272601082289d9c23a5 upstream.
On pseries system (LPAR) xmon failed to enter when running in LE mode,
system is hunging. Inititating xmon will lead to such an output on the
console:
SysRq : Entering xmon
cpu 0x15: Vector: 0 at [
c0000003f39ffb10]
pc:
c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
lr:
c00000000007ed7c: sysrq_handle_xmon+0x5c/0x70
sp:
c0000003f39ffc70
msr:
8000000000009033
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
Bad kernel stack pointer fafb4b0 at eca7cc4
cpu 0x15: Vector: 300 (Data Access) at [
c000000007f07d40]
pc:
000000000eca7cc4
lr:
000000000eca7c44
sp: fafb4b0
msr:
8000000000001000
dar:
10000000
dsisr:
42000000
current = 0xc0000003fafa7180
paca = 0xc000000007d75e80 softe: 0 irq_happened: 0x01
pid = 14617, comm = bash
cpu 0x15: Exception 300 (Data Access) in xmon, returning to main loop
xmon: WARNING: bad recursive fault on cpu 0x15
The root cause is that xmon is calling RTAS to turn off the surveillance
when entering xmon, and RTAS is requiring big endian parameters.
This patch is byte swapping the RTAS arguments when running in LE mode.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Herrenschmidt [Tue, 7 Oct 2014 05:12:55 +0000 (16:12 +1100)]
powerpc/pseries: Honor the generic "no_64bit_msi" flag
commit
415072a041bf50dbd6d56934ffc0cbbe14c97be8 upstream.
Instead of the arch specific quirk which we are deprecating
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Herrenschmidt [Fri, 14 Nov 2014 06:55:03 +0000 (17:55 +1100)]
of/base: Fix PowerPC address parsing hack
commit
746c9e9f92dde2789908e51a354ba90a1962a2eb upstream.
We have a historical hack that treats missing ranges properties as the
equivalent of an empty one. This is needed for ancient PowerMac "bad"
device-trees, and shouldn't be enabled for any other PowerPC platform,
otherwise we get some nasty layout of devices in sysfs or even
duplication when a set of otherwise identically named devices is
created multiple times under a different parent node with no ranges
property.
This fix is needed for the PowerNV i2c busses to be exposed properly
and will fix a number of other embedded cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miaoqing Pan [Thu, 6 Nov 2014 05:22:23 +0000 (10:52 +0530)]
ath9k: Fix RTC_DERIVED_CLK usage
commit
4e6ce4dc7ce71d0886908d55129d5d6482a27ff9 upstream.
Based on the reference clock, which could be 25MHz or 40MHz,
AR_RTC_DERIVED_CLK is programmed differently for AR9340 and AR9550.
But, when a chip reset is done, processing the initvals
sets the register back to the default value.
Fix this by moving the code in ath9k_hw_init_pll() to
ar9003_hw_override_ini(). Also, do this override for AR9531.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 4 Nov 2014 15:52:28 +0000 (16:52 +0100)]
ASoC: dpcm: Fix race between FE/BE updates and trigger
commit
ea9d0d771fcd32cd56070819749477d511ec9117 upstream.
DPCM can update the FE/BE connection states totally asynchronously
from the FE's PCM state. Most of FE/BE state changes are protected by
mutex, so that they won't race, but there are still some actions that
are uncovered. For example, suppose to switch a BE while a FE's
stream is running. This would call soc_dpcm_runtime_update(), which
sets FE's runtime_update flag, then sets up and starts BEs, and clears
FE's runtime_update flag again.
When a device emits XRUN during this operation, the PCM core triggers
snd_pcm_stop(XRUN). Since the trigger action is an atomic ops, this
isn't blocked by the mutex, thus it kicks off DPCM's trigger action.
It eventually updates and clears FE's runtime_update flag while
soc_dpcm_runtime_update() is running concurrently, and it results in
confusion.
Usually, for avoiding such a race, we take a lock. There is a PCM
stream lock for that purpose. However, as already mentioned, the
trigger action is atomic, and we can't take the lock for the whole
soc_dpcm_runtime_update() or other operations that include the lengthy
jobs like hw_params or prepare.
This patch provides an alternative solution. This adds a way to defer
the conflicting trigger callback to be executed at the end of FE/BE
state changes. For doing it, two things are introduced:
- Each runtime_update state change of FEs is protected via PCM stream
lock.
- The FE's trigger callback checks the runtime_update flag. If it's
not set, the trigger action is executed there. If set, mark the
pending trigger action and returns immediately.
- At the exit of runtime_update state change, it checks whether the
pending trigger is present. If yes, it executes the trigger action
at this point.
Reported-and-tested-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Charles Keepax [Mon, 17 Nov 2014 10:48:21 +0000 (10:48 +0000)]
ASoC: wm_adsp: Avoid attempt to free buffers that might still be in use
commit
9da7a5a9fdeeb76b2243f6b473363a7e6147ab6f upstream.
We should not free any buffers associated with writing out coefficients
to the DSP until all the async writes have completed. This patch updates
the out of memory path when allocating a new buffer to include a call to
regmap_async_complete.
Reported-by: JS Park <aitdark.park@samsung.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Estevam [Fri, 14 Nov 2014 04:14:47 +0000 (02:14 -0200)]
ASoC: sgtl5000: Fix SMALL_POP bit definition
commit
c251ea7bd7a04f1f2575467e0de76e803cf59149 upstream.
On a mx28evk with a sgtl5000 codec we notice a loud 'click' sound to happen
5 seconds after the end of a playback.
The SMALL_POP bit should fix this, but its definition is incorrect:
according to the sgtl5000 manual it is bit 0 of CHIP_REF_CTRL register, not
bit 1.
Fix the definition accordingly and enable the bit as intended per the code
comment.
After applying this change, no loud 'click' sound is heard after playback
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kuninori Morimoto [Wed, 29 Oct 2014 04:01:53 +0000 (21:01 -0700)]
ASoC: fsi: remove unsupported PAUSE flag
commit
c1b9b9b1ad2df6144ca3fbe6989f7bd9ea5c5562 upstream.
FSI doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kuninori Morimoto [Wed, 29 Oct 2014 04:02:03 +0000 (21:02 -0700)]
ASoC: rsnd: remove unsupported PAUSE flag
commit
706c66213e5e623e23f521b1acbd8171af7a3549 upstream.
R-Car sound doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Or Gerlitz [Wed, 22 Oct 2014 21:55:49 +0000 (14:55 -0700)]
ib_isert: Add max_send_sge=2 minimum for control PDU responses
commit
f57915cfa5b2b14c1cffa2e83c034f55e3f0e70d upstream.
This patch adds a max_send_sge=2 minimum in isert_conn_setup_qp()
to ensure outgoing control PDU responses with tx_desc->num_sge=2
are able to function correctly.
This addresses a bug with RDMA hardware using dev_attr.max_sge=3,
that in the original code with the ConnectX-2 work-around would
result in isert_conn->max_sge=1 being negotiated.
Originally reported by Chris with ocrdma driver.
Reported-by: Chris Moore <Chris.Moore@emulex.com>
Tested-by: Chris Moore <Chris.Moore@emulex.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Moore [Tue, 4 Nov 2014 16:28:29 +0000 (16:28 +0000)]
IB/isert: Adjust CQ size to HW limits
commit
b1a5ad006b34ded9dc7ec64988deba1b3ecad367 upstream.
isert has an issue of trying to create a CQ with more CQEs than are
supported by the hardware, that currently results in failures during
isert_device creation during first session login.
This is the isert version of the patch that Minh Tran submitted for
iser, and is simple a workaround required to function with existing
ocrdma hardware.
Signed-off-by: Chris Moore <chris.moore@emulex.com>
Reviewied-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxime Ripard [Tue, 18 Nov 2014 22:59:33 +0000 (23:59 +0100)]
clockevent: sun4i: Fix race condition in the probe code
commit
6bab4a8a1888729f17f4923cc5867e4674f66333 upstream.
The interrupts were activated and the handler registered before the clockevent
was registered in the probe function.
The interrupt handler, however, was making the assumption that the clockevent
device was registered.
That could cause a null pointer dereference if the timer interrupt was firing
during this narrow window.
Fix that by moving the clockevent registration before the interrupt is enabled.
Reported-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Benjamin Herrenschmidt [Fri, 3 Oct 2014 05:13:24 +0000 (15:13 +1000)]
PCI/MSI: Add device flag indicating that 64-bit MSIs don't work
commit
f144d1496b47e7450f41b767d0d91c724c2198bc upstream.
This can be set by quirks/drivers to be used by the architecture code
that assigns the MSI addresses.
We additionally add verification in the core MSI code that the values
assigned by the architecture do satisfy the limitation in order to fail
gracefully if they don't (ie. the arch hasn't been updated to deal with
that quirk yet).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yinghai Lu [Wed, 19 Nov 2014 21:30:32 +0000 (14:30 -0700)]
PCI: Support 64-bit bridge windows if we have 64-bit dma_addr_t
commit
7fc986d8a9727e5d40da3c2c1c343da6142e82a9 upstream.
Aaron reported that a 32-bit x86 kernel with Physical Address Extension
(PAE) support complains about bridge prefetchable memory windows above 4GB:
pci_bus 0000:00: root bus resource [mem 0x380000000000-0x383fffffffff]
...
pci 0000:03:00.0: reg 0x10: [mem 0x383fffc00000-0x383fffdfffff 64bit pref]
pci 0000:03:00.0: reg 0x20: [mem 0x383fffe04000-0x383fffe07fff 64bit pref]
pci 0000:03:00.1: reg 0x10: [mem 0x383fffa00000-0x383fffbfffff 64bit pref]
pci 0000:03:00.1: reg 0x20: [mem 0x383fffe00000-0x383fffe03fff 64bit pref]
pci 0000:00:02.2: PCI bridge to [bus 03-04]
pci 0000:00:02.2: bridge window [io 0x1000-0x1fff]
pci 0000:00:02.2: bridge window [mem 0x91900000-0x91cfffff]
pci 0000:00:02.2: can't handle 64-bit address space for bridge
In this kernel, unsigned long is 32 bits and dma_addr_t is 64 bits.
Previously we used "unsigned long" to hold the bridge window address. But
this is a bus address, so we should use dma_addr_t instead.
Use dma_addr_t to hold the bridge window base and limit.
The question of whether the CPU can actually *address* the window is
separate and depends on what the physical address space of the CPU is and
whether the host bridge does any address translation.
[bhelgaas: fix "shift count > width of type", changelog, stable tag]
Fixes:
d56dbf5bab8c ("PCI: Allocate 64-bit BARs above 4G when possible")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=88131
Reported-by: Aaron Ma <mapengyu@gmail.com>
Tested-by: Aaron Ma <mapengyu@gmail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Bohac [Wed, 19 Nov 2014 22:05:49 +0000 (23:05 +0100)]
ipx: fix locking regression in ipx_sendmsg and ipx_recvmsg
[ Upstream commit
01462405f0c093b2f8dfddafcadcda6c9e4c5cdf ]
This fixes an old regression introduced by commit
b0d0d915 (ipx: remove the BKL).
When a recvmsg syscall blocks waiting for new data, no data can be sent on the
same socket with sendmsg because ipx_recvmsg() sleeps with the socket locked.
This breaks mars-nwe (NetWare emulator):
- the ncpserv process reads the request using recvmsg
- ncpserv forks and spawns nwconn
- ncpserv calls a (blocking) recvmsg and waits for new requests
- nwconn deadlocks in sendmsg on the same socket
Commit
b0d0d915 has simply replaced BKL locking with
lock_sock/release_sock. Unlike now, BKL got unlocked while
sleeping, so a blocking recvmsg did not block a concurrent
sendmsg.
Only keep the socket locked while actually working with the socket data and
release it prior to calling skb_recv_datagram().
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Krause [Wed, 19 Nov 2014 17:05:26 +0000 (18:05 +0100)]
pptp: fix stack info leak in pptp_getname()
[ Upstream commit
a5f6fc28d6e6cc379c6839f21820e62262419584 ]
pptp_getname() only partially initializes the stack variable sa,
particularly only fills the pptp part of the sa_addr union. The code
thereby discloses 16 bytes of kernel stack memory via getsockname().
Fix this by memset(0)'ing the union before.
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolay Aleksandrov [Tue, 18 Nov 2014 14:14:44 +0000 (15:14 +0100)]
bonding: fix curr_active_slave/carrier with loadbalance arp monitoring
[ Upstream commit
b8e4500f42fe4464a33a887579147050bed8fcef ]
Since commit
6fde8f037e60 ("bonding: fix locking in
bond_loadbalance_arp_mon()") we can have a stale bond carrier state and
stale curr_active_slave when using arp monitoring in loadbalance modes. The
reason is that in bond_loadbalance_arp_mon() we can't have
do_failover == true but slave_state_changed == false, whenever do_failover
is true then slave_state_changed is also true. Then the following piece
from bond_loadbalance_arp_mon():
if (slave_state_changed) {
bond_slave_state_change(bond);
if (BOND_MODE(bond) == BOND_MODE_XOR)
bond_update_slave_arr(bond, NULL);
} else if (do_failover) {
block_netpoll_tx();
bond_select_active_slave(bond);
unblock_netpoll_tx();
}
will execute only the first branch, always and regardless of do_failover.
Since these two events aren't related in such way, we need to decouple and
consider them separately.
For example this issue could lead to the following result:
Bonding Mode: load balancing (round-robin)
*MII Status: down*
MII Polling Interval (ms): 0
Up Delay (ms): 0
Down Delay (ms): 0
ARP Polling Interval (ms): 100
ARP IP target/s (n.n.n.n form): 192.168.9.2
Slave Interface: ens12
*MII Status: up*
Speed: 10000 Mbps
Duplex: full
Link Failure Count: 2
Permanent HW addr: 00:0f:53:01:42:2c
Slave queue ID: 0
Slave Interface: eth1
*MII Status: up*
Speed: Unknown
Duplex: Unknown
Link Failure Count: 70
Permanent HW addr: 52:54:00:2f:0f:8e
Slave queue ID: 0
Since some interfaces are up, then the status of the bond should also be
up, but it will never change unless something invokes bond_set_carrier()
(i.e. enslave, bond_select_active_slave etc). Now, if I force the
calling of bond_select_active_slave via for example changing
primary_reselect (it can change in any mode), then the MII status goes to
"up" because it calls bond_select_active_slave() which should've been done
from bond_loadbalance_arp_mon() itself.
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Ding Tianhong <dingtianhong@huawei.com>
Fixes:
6fde8f037e60 ("bonding: fix locking in bond_loadbalance_arp_mon()")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Hauke [Sun, 16 Nov 2014 18:55:25 +0000 (19:55 +0100)]
qmi_wwan: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem
[ Upstream commit
bb2bdeb83fb125c95e47fc7eca2a3e8f868e2a74 ]
Added the USB VID/PID for the HP lt4112 LTE/HSPA+ Gobi 4G Modem (Huawei me906e)
Signed-off-by: Martin Hauke <mardnh@gmx.de>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Khoroshilov [Fri, 14 Nov 2014 23:11:59 +0000 (02:11 +0300)]
ieee802154: fix error handling in ieee802154fake_probe()
[ Upstream commit
8c2dd54485ccee7fc4086611e188478584758c8d ]
In case of any failure ieee802154fake_probe() just calls unregister_netdev().
But it does not look safe to unregister netdevice before it was registered.
The patch implements straightforward resource deallocation in case of
failure in ieee802154fake_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Panu Matilainen [Fri, 14 Nov 2014 11:14:32 +0000 (13:14 +0200)]
ipv4: Fix incorrect error code when adding an unreachable route
[ Upstream commit
49dd18ba4615eaa72f15c9087dea1c2ab4744cf5 ]
Trying to add an unreachable route incorrectly returns -ESRCH if
if custom FIB rules are present:
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: Network is unreachable
[root@localhost ~]# ip rule add to 55.66.77.88 table 200
[root@localhost ~]# ip route add 74.125.31.199 dev eth0 via 1.2.3.4
RTNETLINK answers: No such process
[root@localhost ~]#
Commit
83886b6b636173b206f475929e58fac75c6f2446 ("[NET]: Change "not found"
return value for rule lookup") changed fib_rules_lookup()
to use -ESRCH as a "not found" code internally, but for user space it
should be translated into -ENETUNREACH. Handle the translation centrally in
ipv4-specific fib_lookup(), leaving the DECnet case alone.
On a related note, commit
b7a71b51ee37d919e4098cd961d59a883fd272d8
("ipv4: removed redundant conditional") removed a similar translation from
ip_route_input_slow() prematurely AIUI.
Fixes:
b7a71b51ee37 ("ipv4: removed redundant conditional")
Signed-off-by: Panu Matilainen <pmatilai@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vincent BENAYOUN [Thu, 13 Nov 2014 12:47:26 +0000 (13:47 +0100)]
inetdevice: fixed signed integer overflow
[ Upstream commit
84bc88688e3f6ef843aa8803dbcd90168bb89faf ]
There could be a signed overflow in the following code.
The expression, (32-logmask) is comprised between 0 and 31 included.
It may be equal to 31.
In such a case the left shift will produce a signed integer overflow.
According to the C99 Standard, this is an undefined behavior.
A simple fix is to replace the signed int 1 with the unsigned int 1U.
Signed-off-by: Vincent BENAYOUN <vincent.benayoun@trust-in-soft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Sun, 16 Nov 2014 21:19:32 +0000 (13:19 -0800)]
sparc64: Fix constraints on swab helpers.
[ Upstream commit
5a2b59d3993e8ca4f7788a48a23e5cb303f26954 ]
We are reading the memory location, so we have to have a memory
constraint in there purely for the sake of showing the data flow
to the compiler.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Fri, 21 Nov 2014 21:26:07 +0000 (13:26 -0800)]
uprobes, x86: Fix _TIF_UPROBE vs _TIF_NOTIFY_RESUME
commit
82975bc6a6df743b9a01810fb32cb65d0ec5d60b upstream.
x86 call do_notify_resume on paranoid returns if TIF_UPROBE is set but
not on non-paranoid returns. I suspect that this is a mistake and that
the code only works because int3 is paranoid.
Setting _TIF_NOTIFY_RESUME in the uprobe code was probably a workaround
for the x86 bug. With that bug fixed, we can remove _TIF_NOTIFY_RESUME
from the uprobes code.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook [Tue, 18 Nov 2014 00:16:04 +0000 (16:16 -0800)]
x86, kaslr: Handle Gold linker for finding bss/brk
commit
70b61e362187b5fccac206506d402f3424e3e749 upstream.
When building with the Gold linker, the .bss and .brk areas of vmlinux
are shown as consecutive instead of having the same file offset. Allow
for either state, as long as things add up correctly.
Fixes:
e6023367d779 ("x86, kaslr: Prevent .bss from overlaping initrd")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Junjie Mao <eternal.n08@gmail.com>
Link: http://lkml.kernel.org/r/20141118001604.GA25045@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook [Fri, 14 Nov 2014 19:47:37 +0000 (11:47 -0800)]
x86, mm: Set NX across entire PMD at boot
commit
45e2a9d4701d8c624d4a4bcdd1084eae31e92f58 upstream.
When setting up permissions on kernel memory at boot, the end of the
PMD that was split from bss remained executable. It should be NX like
the rest. This performs a PMD alignment instead of a PAGE alignment to
get the correct span of memory.
Before:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82c00000 10M RW PSE GLB NX pmd
0xffffffff82c00000-0xffffffff82df5000 2004K RW GLB NX pte
0xffffffff82df5000-0xffffffff82e00000 44K RW GLB x pte
0xffffffff82e00000-0xffffffffc0000000 978M pmd
After:
---[ High Kernel Mapping ]---
...
0xffffffff8202d000-0xffffffff82200000 1868K RW GLB NX pte
0xffffffff82200000-0xffffffff82e00000 12M RW PSE GLB NX pmd
0xffffffff82e00000-0xffffffffc0000000 978M pmd
[ tglx: Changed it to roundup(_brk_end, PMD_SIZE) and added a comment.
We really should unmap the reminder along with the holes
caused by init,initdata etc. but thats a different issue ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/20141114194737.GA3091@www.outflux.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Tue, 11 Nov 2014 22:01:33 +0000 (14:01 -0800)]
x86: Require exact match for 'noxsave' command line option
commit
2cd3949f702692cf4c5d05b463f19cd706a92dd3 upstream.
We have some very similarly named command-line options:
arch/x86/kernel/cpu/common.c:__setup("noxsave", x86_xsave_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaveopt", x86_xsaveopt_setup);
arch/x86/kernel/cpu/common.c:__setup("noxsaves", x86_xsaves_setup);
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Sun, 23 Nov 2014 02:00:33 +0000 (18:00 -0800)]
x86_64, traps: Rework bad_iret
commit
b645af2d5905c4e32399005b867987919cbfc3ae upstream.
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Sun, 23 Nov 2014 02:00:32 +0000 (18:00 -0800)]
x86_64, traps: Stop using IST for #SS
commit
6f442be2fb22be02cafa606f1769fa1e6f894441 upstream.
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Sun, 23 Nov 2014 02:00:31 +0000 (18:00 -0800)]
x86_64, traps: Fix the espfix64 #DF fixup and rewrite it in C
commit
af726f21ed8af2cdaa4e93098dc211521218ae65 upstream.
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes:
3891a04aafd668686239349ea58f3314ea2af86b
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aaro Koskinen [Wed, 19 Nov 2014 23:05:38 +0000 (01:05 +0200)]
MIPS: Loongson: Make platform serial setup always built-in.
commit
26927f76499849e095714452b8a4e09350f6a3b9 upstream.
If SERIAL_8250 is compiled as a module, the platform specific setup
for Loongson will be a module too, and it will not work very well.
At least on Loongson 3 it will trigger a build failure,
since loongson_sysconf is not exported to modules.
Fix by making the platform specific serial code always built-in.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Markos Chandras <Markos.Chandras@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/8533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aaro Koskinen [Fri, 17 Oct 2014 15:10:24 +0000 (18:10 +0300)]
MIPS: oprofile: Fix backtrace on 64-bit kernel
commit
bbaf113a481b6ce32444c125807ad3618643ce57 upstream.
Fix incorrect cast that always results in wrong address for the new
frame on 64-bit kernels.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8110/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>