Liam R. Howlett [Tue, 11 Apr 2023 15:10:43 +0000 (11:10 -0400)]
maple_tree: fix potential rcu issue
commit
65be6f058b0eba98dc6c6f197ea9f62c9b6a519f upstream.
Ensure the node isn't dead after reading the node end.
Link: https://lkml.kernel.org/r/20230120162650.984577-3-Liam.Howlett@oracle.com
Cc: <Stable@vger.kernel.org>
Fixes:
54a611b60590 ("Maple Tree: add new data structure")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liam R. Howlett [Tue, 11 Apr 2023 15:10:42 +0000 (11:10 -0400)]
maple_tree: remove GFP_ZERO from kmem_cache_alloc() and kmem_cache_alloc_bulk()
commit
541e06b772c1aaffb3b6a245ccface36d7107af2 upstream.
Preallocations are common in the VMA code to avoid allocating under
certain locking conditions. The preallocations must also cover the
worst-case scenario. Removing the GFP_ZERO flag from the
kmem_cache_alloc() (and bulk variant) calls will reduce the amount of time
spent zeroing memory that may not be used. Only zero out the necessary
area to keep track of the allocations in the maple state. Zero the entire
node prior to using it in the tree.
This required internal changes to node counting on allocation, so the test
code is also updated.
This restores some micro-benchmark performance: up to +9% in mmtests mmap1
by my testing +10% to +20% in mmap, mmapaddr, mmapmany tests reported by
Red Hat
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2149636
Link: https://lkml.kernel.org/r/20230105160427.2988454-1-Liam.Howlett@oracle.com
Cc: stable@vger.kernel.org
Fixes:
54a611b60590 ("Maple Tree: add new data structure")
Signed-off-by: Liam Howlett <Liam.Howlett@oracle.com>
Reported-by: Jirka Hladky <jhladky@redhat.com>
Suggested-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alistair Popple [Thu, 30 Mar 2023 01:25:19 +0000 (12:25 +1100)]
mm: take a page reference when removing device exclusive entries
commit
7c7b962938ddda6a9cd095de557ee5250706ea88 upstream.
Device exclusive page table entries are used to prevent CPU access to a
page whilst it is being accessed from a device. Typically this is used to
implement atomic operations when the underlying bus does not support
atomic access. When a CPU thread encounters a device exclusive entry it
locks the page and restores the original entry after calling mmu notifiers
to signal drivers that exclusive access is no longer available.
The device exclusive entry holds a reference to the page making it safe to
access the struct page whilst the entry is present. However the fault
handling code does not hold the PTL when taking the page lock. This means
if there are multiple threads faulting concurrently on the device
exclusive entry one will remove the entry whilst others will wait on the
page lock without holding a reference.
This can lead to threads locking or waiting on a folio with a zero
refcount. Whilst mmap_lock prevents the pages getting freed via munmap()
they may still be freed by a migration. This leads to warnings such as
PAGE_FLAGS_CHECK_AT_FREE due to the page being locked when the refcount
drops to zero.
Fix this by trying to take a reference on the folio before locking it.
The code already checks the PTE under the PTL and aborts if the entry is
no longer there. It is also possible the folio has been unmapped, freed
and re-allocated allowing a reference to be taken on an unrelated folio.
This case is also detected by the PTE check and the folio is unlocked
without further changes.
Link: https://lkml.kernel.org/r/20230330012519.804116-1-apopple@nvidia.com
Fixes:
b756a3b5e7ea ("mm: device exclusive memory access")
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: David Hildenbrand <david@redhat.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Mon, 20 Mar 2023 09:54:33 +0000 (11:54 +0200)]
drm/i915: Split icl_color_commit_noarm() from skl_color_commit_noarm()
commit
76b767d4d1cd052e455cf18e06929e8b2b70101d upstream.
We're going to want different behavior for skl/glk vs. icl
in .color_commit_noarm(), so split the hook into two. Arguably
we already had slightly different behaviour since
csc_enable/gamma_enable are never set on icl+, so the old
code was perhaps a bit confusing as well.
Cc: <stable@vger.kernel.org> #v5.19+
Cc: Manasi Navare <navaremanasi@google.com>
Cc: Drew Davenport <ddavenport@chromium.org>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320095438.17328-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit
f161eb01f50ab31f2084975b43bce54b7b671e17)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Wed, 26 Oct 2022 11:38:57 +0000 (14:38 +0300)]
drm/i915: Use _MMIO_PIPE() for SKL_BOTTOM_COLOR
commit
05ca98523481aa687c5a8dce8939fec539632153 upstream.
No need to use _MMIO_PIPE2() for SKL_BOTTOM_COLOR
since all pipe registers are evenly spread on skl+.
Switch to _MMIO_PIPE() and thus avoid the hidden dev_priv.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026113906.10551-3-ville.syrjala@linux.intel.com
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Foss [Tue, 13 Dec 2022 15:03:04 +0000 (16:03 +0100)]
drm/bridge: lt9611: Fix PLL being unable to lock
commit
2a9df204be0bbb896e087f00b9ee3fc559d5a608 upstream.
This fixes PLL being unable to lock, and is derived from an equivalent
downstream commit.
Available LT9611 documentation does not list this register, neither does
LT9611UXC (which is a different chip).
This commit has been confirmed to fix HDMI output on DragonBoard 845c.
Suggested-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221213150304.4189760-1-robert.foss@linaro.org
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Imre Deak [Mon, 6 Feb 2023 11:48:56 +0000 (13:48 +0200)]
drm/i915/dp_mst: Fix payload removal during output disabling
commit
eb50912ec931913e70640cecf75cb993fd26995f upstream.
Use the correct old/new topology and payload states in
intel_mst_disable_dp(). So far drm_atomic_get_mst_topology_state() it
used returned either the old state, in case the state was added already
earlier during the atomic check phase or otherwise the new state (but
the latter could fail, which can't be handled in the enable/disable
hooks). After the first patch in the patchset, the state should always
get added already during the check phase, so here we can get the
old/new states without a failure.
drm_dp_remove_payload() should use time_slots from the old payload state
and vc_start_slot in the new one. It should update the new payload
states to reflect the sink's current payload table after the payload is
removed. Pass the new topology state and the old and new payload states
accordingly.
This also fixes a problem where the payload allocations for multiple MST
streams on the same link got inconsistent after a few commits, as
during payload removal the old instead of the new payload state got
updated, so the subsequent enabling sequence and commits used a stale
payload state.
v2: Constify the old payload state pointer. (Ville)
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org # 6.1
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-4-imre.deak@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Imre Deak [Mon, 6 Feb 2023 11:48:54 +0000 (13:48 +0200)]
drm/display/dp_mst: Handle old/new payload states in drm_dp_remove_payload()
commit
e761cc20946a0094df71cb31a565a6a0d03bd8be upstream.
Atm, drm_dp_remove_payload() uses the same payload state to both get the
vc_start_slot required for the payload removal DPCD message and to
deduct time_slots from vc_start_slot of all payloads after the one being
removed.
The above isn't always correct, as vc_start_slot must be the up-to-date
version contained in the new payload state, but time_slots must be the
one used when the payload was previously added, contained in the old
payload state. The new payload's time_slots can change vs. the old one
if the current atomic commit changes the corresponding mode.
This patch let's drivers pass the old and new payload states to
drm_dp_remove_payload(), but keeps these the same for now in all drivers
not to change the behavior. A follow-up i915 patch will pass in that
driver the correct old and new states to the function.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org # 6.1
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Lyude Paul <lyude@redhat.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230206114856.2665066-2-imre.deak@intel.com
Hand modified for missing
8c7d980da9ba3eb67a1b40fd4b33bcf49397084b
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Huang [Fri, 20 Jan 2023 14:27:32 +0000 (22:27 +0800)]
drm/amdgpu: skip psp suspend for IMU enabled ASICs mode2 reset
commit
e11c775030c5585370fda43035204bb5fa23b139 upstream.
The psp suspend & resume should be skipped to avoid destroy
the TMR and reload FWs again for IMU enabled APU ASICs.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Deucher [Fri, 2 Dec 2022 15:13:40 +0000 (10:13 -0500)]
drm/amdgpu: for S0ix, skip SDMA 5.x+ suspend/resume
commit
2a7798ea7390fd78f191c9e9bf68f5581d3b4a02 upstream.
SDMA 5.x is part of the GFX block so it's controlled via
GFXOFF. Skip suspend as it should be handled the same
as GFX.
v2: drop SDMA 4.x. That requires special handling.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Li [Thu, 1 Dec 2022 14:49:23 +0000 (09:49 -0500)]
drm/amd/display: Clear MST topology if it fails to resume
commit
3f6752b4de41896c7f1609b1585db2080e8150d8 upstream.
[Why]
In case of failure to resume MST topology after suspend, an emtpty
mst tree prevents further mst hub detection on the same connector.
That causes the issue with MST hub hotplug after it's been unplug in
suspend.
[How]
Stop topology manager on the connector after detecting DM_MST failure.
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kemeng Shi [Mon, 5 Dec 2022 11:57:02 +0000 (19:57 +0800)]
blk-throttle: Fix that bps of child could exceed bps limited in parent
commit
84aca0a7e039c8735abc0f89f3f48e9006c0dfc7 upstream.
Consider situation as following (on the default hierarchy):
HDD
|
root (bps limit: 4k)
|
child (bps limit :8k)
|
fio bs=8k
Rate of fio is supposed to be 4k, but result is 8k. Reason is as
following:
Size of single IO from fio is larger than bytes allowed in one
throtl_slice in child, so IOs are always queued in child group first.
When queued IOs in child are dispatched to parent group, BIO_BPS_THROTTLED
is set and these IOs will not be limited by tg_within_bps_limit anymore.
Fix this by only set BIO_BPS_THROTTLED when the bio traversed the entire
tree.
There patch has no influence on situation which is not on the default
hierarchy as each group is a single root group without parent.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kemeng Shi <shikemeng@huawei.com>
Link: https://lore.kernel.org/r/20221205115709.251489-3-shikemeng@huaweicloud.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Cc: Khazhy Kumykov <khazhy@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peng Zhang [Tue, 14 Mar 2023 12:42:03 +0000 (20:42 +0800)]
maple_tree: fix a potential concurrency bug in RCU mode
commit
c45ea315a602d45569b08b93e9ab30f6a63a38aa upstream.
There is a concurrency bug that may cause the wrong value to be loaded
when a CPU is modifying the maple tree.
CPU1:
mtree_insert_range()
mas_insert()
mas_store_root()
...
mas_root_expand()
...
rcu_assign_pointer(mas->tree->ma_root, mte_mk_root(mas->node));
ma_set_meta(node, maple_leaf_64, 0, slot); <---IP
CPU2:
mtree_load()
mtree_lookup_walk()
ma_data_end();
When CPU1 is about to execute the instruction pointed to by IP, the
ma_data_end() executed by CPU2 may return the wrong end position, which
will cause the value loaded by mtree_load() to be wrong.
An example of triggering the bug:
Add mdelay(100) between rcu_assign_pointer() and ma_set_meta() in
mas_root_expand().
static DEFINE_MTREE(tree);
int work(void *p) {
unsigned long val;
for (int i = 0 ; i< 30; ++i) {
val = (unsigned long)mtree_load(&tree, 8);
mdelay(5);
pr_info("%lu",val);
}
return 0;
}
mt_init_flags(&tree, MT_FLAGS_USE_RCU);
mtree_insert(&tree, 0, (void*)12345, GFP_KERNEL);
run_thread(work)
mtree_insert(&tree, 1, (void*)56789, GFP_KERNEL);
In RCU mode, mtree_load() should always return the value before or after
the data structure is modified, and in this example mtree_load(&tree, 8)
may return 56789 which is not expected, it should always return NULL. Fix
it by put ma_set_meta() before rcu_assign_pointer().
Link: https://lkml.kernel.org/r/20230314124203.91572-4-zhangpeng.00@bytedance.com
Fixes:
54a611b60590 ("Maple Tree: add new data structure")
Signed-off-by: Peng Zhang <zhangpeng.00@bytedance.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peng Zhang [Tue, 14 Mar 2023 12:42:01 +0000 (20:42 +0800)]
maple_tree: fix get wrong data_end in mtree_lookup_walk()
commit
ec07967d7523adb3670f9dfee0232e3bc868f3de upstream.
if (likely(offset > end))
max = pivots[offset];
The above code should be changed to if (likely(offset < end)), which is
correct. This affects the correctness of ma_data_end(). Now it seems
that the final result will not be wrong, but it is best to change it.
This patch does not change the code as above, because it simplifies the
code by the way.
Link: https://lkml.kernel.org/r/20230314124203.91572-1-zhangpeng.00@bytedance.com
Link: https://lkml.kernel.org/r/20230314124203.91572-2-zhangpeng.00@bytedance.com
Fixes:
54a611b60590 ("Maple Tree: add new data structure")
Signed-off-by: Peng Zhang <zhangpeng.00@bytedance.com>
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Xu [Tue, 21 Mar 2023 19:18:40 +0000 (15:18 -0400)]
mm/hugetlb: fix uffd wr-protection for CoW optimization path
commit
60d5b473d61be61ac315e544fcd6a8234a79500e upstream.
This patch fixes an issue that a hugetlb uffd-wr-protected mapping can be
writable even with uffd-wp bit set. It only happens with hugetlb private
mappings, when someone firstly wr-protects a missing pte (which will
install a pte marker), then a write to the same page without any prior
access to the page.
Userfaultfd-wp trap for hugetlb was implemented in hugetlb_fault() before
reaching hugetlb_wp() to avoid taking more locks that userfault won't
need. However there's one CoW optimization path that can trigger
hugetlb_wp() inside hugetlb_no_page(), which will bypass the trap.
This patch skips hugetlb_wp() for CoW and retries the fault if uffd-wp bit
is detected. The new path will only trigger in the CoW optimization path
because generic hugetlb_fault() (e.g. when a present pte was
wr-protected) will resolve the uffd-wp bit already. Also make sure
anonymous UNSHARE won't be affected and can still be resolved, IOW only
skip CoW not CoR.
This patch will be needed for v5.19+ hence copy stable.
[peterx@redhat.com: v2]
Link: https://lkml.kernel.org/r/ZBzOqwF2wrHgBVZb@x1n
[peterx@redhat.com: v3]
Link: https://lkml.kernel.org/r/20230324142620.2344140-1-peterx@redhat.com
Link: https://lkml.kernel.org/r/20230321191840.1897940-1-peterx@redhat.com
Fixes:
166f3ecc0daf ("mm/hugetlb: hook page faults for uffd write protection")
Signed-off-by: Peter Xu <peterx@redhat.com>
Reported-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Tested-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Axel Rasmussen <axelrasmussen@google.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rongwei Wang [Tue, 4 Apr 2023 15:47:16 +0000 (23:47 +0800)]
mm/swap: fix swap_info_struct race between swapoff and get_swap_pages()
commit
6fe7d6b992113719e96744d974212df3fcddc76c upstream.
The si->lock must be held when deleting the si from the available list.
Otherwise, another thread can re-add the si to the available list, which
can lead to memory corruption. The only place we have found where this
happens is in the swapoff path. This case can be described as below:
core 0 core 1
swapoff
del_from_avail_list(si) waiting
try lock si->lock acquire swap_avail_lock
and re-add si into
swap_avail_head
acquire si->lock but missing si already being added again, and continuing
to clear SWP_WRITEOK, etc.
It can be easily found that a massive warning messages can be triggered
inside get_swap_pages() by some special cases, for example, we call
madvise(MADV_PAGEOUT) on blocks of touched memory concurrently, meanwhile,
run much swapon-swapoff operations (e.g. stress-ng-swap).
However, in the worst case, panic can be caused by the above scene. In
swapoff(), the memory used by si could be kept in swap_info[] after
turning off a swap. This means memory corruption will not be caused
immediately until allocated and reset for a new swap in the swapon path.
A panic message caused: (with CONFIG_PLIST_DEBUG enabled)
------------[ cut here ]------------
top:
00000000e58a3003, n:
0000000013e75cda, p:
000000008cd4451a
prev:
0000000035b1e58a, n:
000000008cd4451a, p:
000000002150ee8d
next:
000000008cd4451a, n:
000000008cd4451a, p:
000000008cd4451a
WARNING: CPU: 21 PID: 1843 at lib/plist.c:60 plist_check_prev_next_node+0x50/0x70
Modules linked in: rfkill(E) crct10dif_ce(E)...
CPU: 21 PID: 1843 Comm: stress-ng Kdump: ... 5.10.134+
Hardware name: Alibaba Cloud ECS, BIOS 0.0.0 02/06/2015
pstate:
60400005 (nZCv daif +PAN -UAO -TCO BTYPE=--)
pc : plist_check_prev_next_node+0x50/0x70
lr : plist_check_prev_next_node+0x50/0x70
sp :
ffff0018009d3c30
x29:
ffff0018009d3c40 x28:
ffff800011b32a98
x27:
0000000000000000 x26:
ffff001803908000
x25:
ffff8000128ea088 x24:
ffff800011b32a48
x23:
0000000000000028 x22:
ffff001800875c00
x21:
ffff800010f9e520 x20:
ffff001800875c00
x19:
ffff001800fdc6e0 x18:
0000000000000030
x17:
0000000000000000 x16:
0000000000000000
x15:
0736076307640766 x14:
0730073007380731
x13:
0736076307640766 x12:
0730073007380731
x11:
000000000004058d x10:
0000000085a85b76
x9 :
ffff8000101436e4 x8 :
ffff800011c8ce08
x7 :
0000000000000000 x6 :
0000000000000001
x5 :
ffff0017df9ed338 x4 :
0000000000000001
x3 :
ffff8017ce62a000 x2 :
ffff0017df9ed340
x1 :
0000000000000000 x0 :
0000000000000000
Call trace:
plist_check_prev_next_node+0x50/0x70
plist_check_head+0x80/0xf0
plist_add+0x28/0x140
add_to_avail_list+0x9c/0xf0
_enable_swap_info+0x78/0xb4
__do_sys_swapon+0x918/0xa10
__arm64_sys_swapon+0x20/0x30
el0_svc_common+0x8c/0x220
do_el0_svc+0x2c/0x90
el0_svc+0x1c/0x30
el0_sync_handler+0xa8/0xb0
el0_sync+0x148/0x180
irq event stamp: 2082270
Now, si->lock locked before calling 'del_from_avail_list()' to make sure
other thread see the si had been deleted and SWP_WRITEOK cleared together,
will not reinsert again.
This problem exists in versions after stable 5.10.y.
Link: https://lkml.kernel.org/r/20230404154716.23058-1-rongwei.wang@linux.alibaba.com
Fixes:
a2468cc9bfdff ("swap: choose swap device according to numa node")
Tested-by: Yongchen Yin <wb-yyc939293@alibaba-inc.com>
Signed-off-by: Rongwei Wang <rongwei.wang@linux.alibaba.com>
Cc: Bagas Sanjaya <bagasdotme@gmail.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zheng Yejian [Sat, 25 Mar 2023 02:12:47 +0000 (10:12 +0800)]
ring-buffer: Fix race while reader and writer are on the same page
commit
6455b6163d8c680366663cdb8c679514d55fc30c upstream.
When user reads file 'trace_pipe', kernel keeps printing following logs
that warn at "cpu_buffer->reader_page->read > rb_page_size(reader)" in
rb_get_reader_page(). It just looks like there's an infinite loop in
tracing_read_pipe(). This problem occurs several times on arm64 platform
when testing v5.10 and below.
Call trace:
rb_get_reader_page+0x248/0x1300
rb_buffer_peek+0x34/0x160
ring_buffer_peek+0xbc/0x224
peek_next_entry+0x98/0xbc
__find_next_entry+0xc4/0x1c0
trace_find_next_entry_inc+0x30/0x94
tracing_read_pipe+0x198/0x304
vfs_read+0xb4/0x1e0
ksys_read+0x74/0x100
__arm64_sys_read+0x24/0x30
el0_svc_common.constprop.0+0x7c/0x1bc
do_el0_svc+0x2c/0x94
el0_svc+0x20/0x30
el0_sync_handler+0xb0/0xb4
el0_sync+0x160/0x180
Then I dump the vmcore and look into the problematic per_cpu ring_buffer,
I found that tail_page/commit_page/reader_page are on the same page while
reader_page->read is obviously abnormal:
tail_page == commit_page == reader_page == {
.write = 0x100d20,
.read = 0x8f9f4805, // Far greater than 0xd20, obviously abnormal!!!
.entries = 0x10004c,
.real_end = 0x0,
.page = {
.time_stamp = 0x857257416af0,
.commit = 0xd20, // This page hasn't been full filled.
// .data[0...0xd20] seems normal.
}
}
The root cause is most likely the race that reader and writer are on the
same page while reader saw an event that not fully committed by writer.
To fix this, add memory barriers to make sure the reader can see the
content of what is committed. Since commit
a0fcaaed0c46 ("ring-buffer: Fix
race between reset page and reading page") has added the read barrier in
rb_get_reader_page(), here we just need to add the write barrier.
Link: https://lore.kernel.org/linux-trace-kernel/20230325021247.2923907-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Fixes:
77ae365eca89 ("ring-buffer: make lockless")
Suggested-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Min Li [Tue, 28 Mar 2023 09:36:27 +0000 (17:36 +0800)]
drm/i915: fix race condition UAF in i915_perf_add_config_ioctl
commit
dc30c011469165d57af9adac5baff7d767d20e5c upstream.
Userspace can guess the id value and try to race oa_config object creation
with config remove, resulting in a use-after-free if we dereference the
object after unlocking the metrics_lock. For that reason, unlocking the
metrics_lock must be done after we are done dereferencing the object.
Signed-off-by: Min Li <lm0963hack@gmail.com>
Fixes:
f89823c21224 ("drm/i915/perf: Implement I915_PERF_ADD/REMOVE_CONFIG interface")
Cc: <stable@vger.kernel.org> # v4.14+
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230328093627.5067-1-lm0963hack@gmail.com
[tursulin: Manually added stable tag.]
(cherry picked from commit
49f6f6483b652108bcb73accd0204a464b922395)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tvrtko Ursulin [Mon, 20 Mar 2023 15:14:23 +0000 (15:14 +0000)]
drm/i915: Fix context runtime accounting
commit
dc3421560a67361442f33ec962fc6dd48895a0df upstream.
When considering whether to mark one context as stopped and another as
started we need to look at whether the previous and new _contexts_ are
different and not just requests. Otherwise the software tracked context
start time was incorrectly updated to the most recent lite-restore time-
stamp, which was in some cases resulting in active time going backward,
until the context switch (typically the heartbeat pulse) would synchronise
with the hardware tracked context runtime. Easiest use case to observe
this behaviour was with a full screen clients with close to 100% engine
load.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes:
bb6287cb1886 ("drm/i915: Track context current active time")
Cc: <stable@vger.kernel.org> # v5.19+
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320151423.1708436-1-tvrtko.ursulin@linux.intel.com
[tursulin: Fix spelling in commit msg.]
(cherry picked from commit
b3e70051879c665acdd3a1ab50d0ed58d6a8001f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Karol Herbst [Thu, 30 Mar 2023 22:39:38 +0000 (00:39 +0200)]
drm/nouveau/disp: Support more modes by checking with lower bpc
commit
7f67aa097e875c87fba024e850cf405342300059 upstream.
This allows us to advertise more modes especially on HDR displays.
Fixes using 4K@60 modes on my TV and main display both using a HDMI to DP
adapter. Also fixes similar issues for users running into this.
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230330223938.4025569-1-kherbst@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boris Brezillon [Fri, 21 May 2021 09:38:11 +0000 (11:38 +0200)]
drm/panfrost: Fix the panfrost_mmu_map_fault_addr() error path
commit
764a2ab9eb56e1200083e771aab16186836edf1d upstream.
Make sure all bo->base.pages entries are either NULL or pointing to a
valid page before calling drm_gem_shmem_put_pages().
Reported-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: <stable@vger.kernel.org>
Fixes:
187d2929206e ("drm/panfrost: Add support for GPU heap allocations")
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210521093811.1018992-1-boris.brezillon@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jens Axboe [Thu, 6 Apr 2023 02:00:46 +0000 (20:00 -0600)]
ublk: read any SQE values upfront
commit
8c68ae3b22fa6fb2dbe83ef955ff10936503d28e upstream.
Since SQE memory is shared with userspace, we should only be reading it
once. We cannot read it multiple times, particularly when it's read once
for validation and then read again for the actual use.
ublk_ch_uring_cmd() is safe when called as a retry operation, as the
memory backing is stable at that point. But for normal issue, we want
to ensure that we only read ublksrv_io_cmd once. Wrap the function in
a helper that reads the value into an on-stack copy of the struct.
Cc: stable@vger.kernel.org # 6.0+
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Thu, 30 Mar 2023 09:12:59 +0000 (11:12 +0200)]
wifi: mt76: ignore key disable commands
commit
e6db67fa871dee37d22701daba806bfcd4d9df49 upstream.
This helps avoid cleartext leakage of already queued or powersave buffered
packets, when a reassoc triggers the key deletion.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330091259.61378-1-nbd@nbd.name
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yafang Shao [Thu, 30 Mar 2023 16:26:25 +0000 (16:26 +0000)]
mm: vmalloc: avoid warn_alloc noise caused by fatal signal
commit
f349b15e183d6956f1b63d6ff57849ff10c7edd5 upstream.
There're some suspicious warn_alloc on my test serer, for example,
[13366.518837] warn_alloc: 81 callbacks suppressed
[13366.518841] test_verifier: vmalloc error: size 4096, page order 0, failed to allocate pages, mode:0x500dc2(GFP_HIGHUSER|__GFP_ZERO|__GFP_ACCOUNT), nodemask=(null),cpuset=/,mems_allowed=0-1
[13366.522240] CPU: 30 PID: 722463 Comm: test_verifier Kdump: loaded Tainted: G W O 6.2.0+ #638
[13366.524216] Call Trace:
[13366.524702] <TASK>
[13366.525148] dump_stack_lvl+0x6c/0x80
[13366.525712] dump_stack+0x10/0x20
[13366.526239] warn_alloc+0x119/0x190
[13366.526783] ? alloc_pages_bulk_array_mempolicy+0x9e/0x2a0
[13366.527470] __vmalloc_area_node+0x546/0x5b0
[13366.528066] __vmalloc_node_range+0xc2/0x210
[13366.528660] __vmalloc_node+0x42/0x50
[13366.529186] ? bpf_prog_realloc+0x53/0xc0
[13366.529743] __vmalloc+0x1e/0x30
[13366.530235] bpf_prog_realloc+0x53/0xc0
[13366.530771] bpf_patch_insn_single+0x80/0x1b0
[13366.531351] bpf_jit_blind_constants+0xe9/0x1c0
[13366.531932] ? __free_pages+0xee/0x100
[13366.532457] ? free_large_kmalloc+0x58/0xb0
[13366.533002] bpf_int_jit_compile+0x8c/0x5e0
[13366.533546] bpf_prog_select_runtime+0xb4/0x100
[13366.534108] bpf_prog_load+0x6b1/0xa50
[13366.534610] ? perf_event_task_tick+0x96/0xb0
[13366.535151] ? security_capable+0x3a/0x60
[13366.535663] __sys_bpf+0xb38/0x2190
[13366.536120] ? kvm_clock_get_cycles+0x9/0x10
[13366.536643] __x64_sys_bpf+0x1c/0x30
[13366.537094] do_syscall_64+0x38/0x90
[13366.537554] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[13366.538107] RIP: 0033:0x7f78310f8e29
[13366.538561] Code: 01 00 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 17 e0 2c 00 f7 d8 64 89 01 48
[13366.540286] RSP: 002b:
00007ffe2a61fff8 EFLAGS:
00000206 ORIG_RAX:
0000000000000141
[13366.541031] RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007f78310f8e29
[13366.541749] RDX:
0000000000000080 RSI:
00007ffe2a6200b0 RDI:
0000000000000005
[13366.542470] RBP:
00007ffe2a620010 R08:
00007ffe2a6202a0 R09:
00007ffe2a6200b0
[13366.543183] R10:
00000000000f423e R11:
0000000000000206 R12:
0000000000407800
[13366.543900] R13:
00007ffe2a620540 R14:
0000000000000000 R15:
0000000000000000
[13366.544623] </TASK>
[13366.545260] Mem-Info:
[13366.546121] active_anon:81319 inactive_anon:20733 isolated_anon:0
active_file:69450 inactive_file:5624 isolated_file:0
unevictable:0 dirty:10 writeback:0
slab_reclaimable:69649 slab_unreclaimable:48930
mapped:27400 shmem:12868 pagetables:4929
sec_pagetables:0 bounce:0
kernel_misc_reclaimable:0
free:
15870308 free_pcp:142935 free_cma:0
[13366.551886] Node 0 active_anon:224836kB inactive_anon:33528kB active_file:175692kB inactive_file:13752kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:59248kB dirty:32kB writeback:0kB shmem:18252kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 0kB writeback_tmp:0kB kernel_stack:4616kB pagetables:10664kB sec_pagetables:0kB all_unreclaimable? no
[13366.555184] Node 1 active_anon:100440kB inactive_anon:49404kB active_file:102108kB inactive_file:8744kB unevictable:0kB isolated(anon):0kB isolated(file):0kB mapped:50352kB dirty:8kB writeback:0kB shmem:33220kB shmem_thp: 0kB shmem_pmdmapped: 0kB anon_thp: 0kB writeback_tmp:0kB kernel_stack:3896kB pagetables:9052kB sec_pagetables:0kB all_unreclaimable? no
[13366.558262] Node 0 DMA free:15360kB boost:0kB min:304kB low:380kB high:456kB reserved_highatomic:0KB active_anon:0kB inactive_anon:0kB active_file:0kB inactive_file:0kB unevictable:0kB writepending:0kB present:15992kB managed:15360kB mlocked:0kB bounce:0kB free_pcp:0kB local_pcp:0kB free_cma:0kB
[13366.560821] lowmem_reserve[]: 0 2735 31873 31873 31873
[13366.561981] Node 0 DMA32 free:2790904kB boost:0kB min:56028kB low:70032kB high:84036kB reserved_highatomic:0KB active_anon:1936kB inactive_anon:20kB active_file:396kB inactive_file:344kB unevictable:0kB writepending:0kB present:3129200kB managed:2801520kB mlocked:0kB bounce:0kB free_pcp:5188kB local_pcp:0kB free_cma:0kB
[13366.565148] lowmem_reserve[]: 0 0 29137 29137 29137
[13366.566168] Node 0 Normal free:28533824kB boost:0kB min:596740kB low:745924kB high:895108kB reserved_highatomic:28672KB active_anon:222900kB inactive_anon:33508kB active_file:175296kB inactive_file:13408kB unevictable:0kB writepending:32kB present:30408704kB managed:29837172kB mlocked:0kB bounce:0kB free_pcp:295724kB local_pcp:0kB free_cma:0kB
[13366.569485] lowmem_reserve[]: 0 0 0 0 0
[13366.570416] Node 1 Normal free:32141144kB boost:0kB min:660504kB low:825628kB high:990752kB reserved_highatomic:69632KB active_anon:100440kB inactive_anon:49404kB active_file:102108kB inactive_file:8744kB unevictable:0kB writepending:8kB present:33554432kB managed:33025372kB mlocked:0kB bounce:0kB free_pcp:270880kB local_pcp:46860kB free_cma:0kB
[13366.573403] lowmem_reserve[]: 0 0 0 0 0
[13366.574015] Node 0 DMA: 0*4kB 0*8kB 0*16kB 0*32kB 0*64kB 0*128kB 0*256kB 0*512kB 1*1024kB (U) 1*2048kB (M) 3*4096kB (M) = 15360kB
[13366.575474] Node 0 DMA32: 782*4kB (UME) 756*8kB (UME) 736*16kB (UME) 745*32kB (UME) 694*64kB (UME) 653*128kB (UME) 595*256kB (UME) 552*512kB (UME) 454*1024kB (UME) 347*2048kB (UME) 246*4096kB (UME) = 2790904kB
[13366.577442] Node 0 Normal: 33856*4kB (UMEH) 51815*8kB (UMEH) 42418*16kB (UMEH) 36272*32kB (UMEH) 22195*64kB (UMEH) 10296*128kB (UMEH) 7238*256kB (UMEH) 5638*512kB (UEH) 5337*1024kB (UMEH) 3506*2048kB (UMEH) 1470*4096kB (UME) = 28533784kB
[13366.580460] Node 1 Normal: 15776*4kB (UMEH) 37485*8kB (UMEH) 29509*16kB (UMEH) 21420*32kB (UMEH) 14818*64kB (UMEH) 13051*128kB (UMEH) 9918*256kB (UMEH) 7374*512kB (UMEH) 5397*1024kB (UMEH) 3887*2048kB (UMEH) 2002*4096kB (UME) = 32141240kB
[13366.583027] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=1048576kB
[13366.584380] Node 0 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB
[13366.585702] Node 1 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=1048576kB
[13366.587042] Node 1 hugepages_total=0 hugepages_free=0 hugepages_surp=0 hugepages_size=2048kB
[13366.588372] 87386 total pagecache pages
[13366.589266] 0 pages in swap cache
[13366.590327] Free swap = 0kB
[13366.591227] Total swap = 0kB
[13366.592142]
16777082 pages RAM
[13366.593057] 0 pages HighMem/MovableOnly
[13366.594037] 357226 pages reserved
[13366.594979] 0 pages hwpoisoned
This failure really confuse me as there're still lots of available pages.
Finally I figured out it was caused by a fatal signal. When a process is
allocating memory via vm_area_alloc_pages(), it will break directly even
if it hasn't allocated the requested pages when it receives a fatal
signal. In that case, we shouldn't show this warn_alloc, as it is
useless. We only need to show this warning when there're really no enough
pages.
Link: https://lkml.kernel.org/r/20230330162625.13604-1-laoar.shao@gmail.com
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Reviewed-by: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sergey Senozhatsky [Sat, 25 Mar 2023 02:46:31 +0000 (11:46 +0900)]
zsmalloc: document freeable stats
commit
618a8a917dbf5830e2064d2fa0568940eb5d2584 upstream.
When freeable class stat was added to classes file (back in 2016) we
forgot to update zsmalloc documentation. Fix that.
Link: https://lkml.kernel.org/r/20230325024631.2817153-3-senozhatsky@chromium.org
Fixes:
1120ed548394 ("mm/zsmalloc: add `freeable' column to pool stat")
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt (Google) [Thu, 6 Apr 2023 15:10:33 +0000 (11:10 -0400)]
tracing/synthetic: Make lastcmd_mutex static
commit
31c683967174b487939efaf65e41f5ff1404e141 upstream.
The lastcmd_mutex is only used in trace_events_synth.c and should be
static.
Link: https://lore.kernel.org/linux-trace-kernel/202304062033.cRStgOuP-lkp@intel.com/
Link: https://lore.kernel.org/linux-trace-kernel/20230406111033.6e26de93@gandalf.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Tze-nan Wu <Tze-nan.Wu@mediatek.com>
Fixes:
4ccf11c4e8a8e ("tracing/synthetic: Fix races on freeing last_cmd")
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Montleon [Fri, 24 Mar 2023 17:07:11 +0000 (13:07 -0400)]
ASoC: hdac_hdmi: use set_stream() instead of set_tdm_slots()
commit
f6887a71bdd2f0dcba9b8180dd2223cfa8637e85 upstream.
hdac_hdmi was not updated to use set_stream() instead of set_tdm_slots()
in the original commit so HDMI no longer produces audio.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/regressions/CAJD_bPKQdtaExvVEKxhQ47G-ZXDA=k+gzhMJRHLBe=mysPnuKA@mail.gmail.com/
Fixes:
636110411ca7 ("ASoC: Intel/SOF: use set_stream() instead of set_tdm_slots() for HDAudio")
Signed-off-by: Jason Montleon <jmontleo@redhat.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230324170711.2526-1-jmontleo@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt (Google) [Tue, 4 Apr 2023 23:45:04 +0000 (19:45 -0400)]
tracing: Free error logs of tracing instances
commit
3357c6e429643231e60447b52ffbb7ac895aca22 upstream.
When a tracing instance is removed, the error messages that hold errors
that occurred in the instance needs to be freed. The following reports a
memory leak:
# cd /sys/kernel/tracing
# mkdir instances/foo
# echo 'hist:keys=x' > instances/foo/events/sched/sched_switch/trigger
# cat instances/foo/error_log
[ 117.404795] hist:sched:sched_switch: error: Couldn't find field
Command: hist:keys=x
^
# rmdir instances/foo
Then check for memory leaks:
# echo scan > /sys/kernel/debug/kmemleak
# cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff88810d8ec700 (size 192):
comm "bash", pid 869, jiffies
4294950577 (age 215.752s)
hex dump (first 32 bytes):
60 dd 68 61 81 88 ff ff 60 dd 68 61 81 88 ff ff `.ha....`.ha....
a0 30 8c 83 ff ff ff ff 26 00 0a 00 00 00 00 00 .0......&.......
backtrace:
[<
00000000dae26536>] kmalloc_trace+0x2a/0xa0
[<
00000000b2938940>] tracing_log_err+0x277/0x2e0
[<
000000004a0e1b07>] parse_atom+0x966/0xb40
[<
0000000023b24337>] parse_expr+0x5f3/0xdb0
[<
00000000594ad074>] event_hist_trigger_parse+0x27f8/0x3560
[<
00000000293a9645>] trigger_process_regex+0x135/0x1a0
[<
000000005c22b4f2>] event_trigger_write+0x87/0xf0
[<
000000002cadc509>] vfs_write+0x162/0x670
[<
0000000059c3b9be>] ksys_write+0xca/0x170
[<
00000000f1cddc00>] do_syscall_64+0x3e/0xc0
[<
00000000868ac68c>] entry_SYSCALL_64_after_hwframe+0x72/0xdc
unreferenced object 0xffff888170c35a00 (size 32):
comm "bash", pid 869, jiffies
4294950577 (age 215.752s)
hex dump (first 32 bytes):
0a 20 20 43 6f 6d 6d 61 6e 64 3a 20 68 69 73 74 . Command: hist
3a 6b 65 79 73 3d 78 0a 00 00 00 00 00 00 00 00 :keys=x.........
backtrace:
[<
000000006a747de5>] __kmalloc+0x4d/0x160
[<
000000000039df5f>] tracing_log_err+0x29b/0x2e0
[<
000000004a0e1b07>] parse_atom+0x966/0xb40
[<
0000000023b24337>] parse_expr+0x5f3/0xdb0
[<
00000000594ad074>] event_hist_trigger_parse+0x27f8/0x3560
[<
00000000293a9645>] trigger_process_regex+0x135/0x1a0
[<
000000005c22b4f2>] event_trigger_write+0x87/0xf0
[<
000000002cadc509>] vfs_write+0x162/0x670
[<
0000000059c3b9be>] ksys_write+0xca/0x170
[<
00000000f1cddc00>] do_syscall_64+0x3e/0xc0
[<
00000000868ac68c>] entry_SYSCALL_64_after_hwframe+0x72/0xdc
The problem is that the error log needs to be freed when the instance is
removed.
Link: https://lore.kernel.org/lkml/76134d9f-a5ba-6a0d-37b3-28310b4a1e91@alu.unizg.hr/
Link: https://lore.kernel.org/linux-trace-kernel/20230404194504.5790b95f@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Biggers <ebiggers@kernel.org>
Fixes:
2f754e771b1a6 ("tracing: Have the error logs show up in the proper instances")
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Bristot de Oliveira [Wed, 29 Mar 2023 15:50:16 +0000 (17:50 +0200)]
tracing/osnoise: Fix notify new tracing_max_latency
commit
d3cba7f02cd82118c32651c73374d8a5a459d9a6 upstream.
osnoise/timerlat tracers are reporting new max latency on instances
where the tracing is off, creating inconsistencies between the max
reported values in the trace and in the tracing_max_latency. Thus
only report new tracing_max_latency on active tracing instances.
Link: https://lkml.kernel.org/r/ecd109fde4a0c24ab0f00ba1e9a144ac19a91322.1680104184.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Fixes:
dae181349f1e ("tracing/osnoise: Support a list of trace_array *tr")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Bristot de Oliveira [Wed, 29 Mar 2023 15:50:15 +0000 (17:50 +0200)]
tracing/timerlat: Notify new max thread latency
commit
b9f451a9029a16eb7913ace09b92493d00f2e564 upstream.
timerlat is not reporting a new tracing_max_latency for the thread
latency. The reason is that it is not calling notify_new_max_latency()
function after the new thread latency is sampled.
Call notify_new_max_latency() after computing the thread latency.
Link: https://lkml.kernel.org/r/16e18d61d69073d0192ace07bf61e405cca96e9c.1680104184.git.bristot@kernel.org
Cc: stable@vger.kernel.org
Fixes:
dae181349f1e ("tracing/osnoise: Support a list of trace_array *tr")
Signed-off-by: Daniel Bristot de Oliveira <bristot@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tze-nan Wu [Tue, 21 Mar 2023 11:04:43 +0000 (19:04 +0800)]
tracing/synthetic: Fix races on freeing last_cmd
commit
4ccf11c4e8a8e051499d53a12f502196c97a758e upstream.
Currently, the "last_cmd" variable can be accessed by multiple processes
asynchronously when multiple users manipulate synthetic_events node
at the same time, it could lead to use-after-free or double-free.
This patch add "lastcmd_mutex" to prevent "last_cmd" from being accessed
asynchronously.
================================================================
It's easy to reproduce in the KASAN environment by running the two
scripts below in different shells.
script 1:
while :
do
echo -n -e '\x88' > /sys/kernel/tracing/synthetic_events
done
script 2:
while :
do
echo -n -e '\xb0' > /sys/kernel/tracing/synthetic_events
done
================================================================
double-free scenario:
process A process B
------------------- ---------------
1.kstrdup last_cmd
2.free last_cmd
3.free last_cmd(double-free)
================================================================
use-after-free scenario:
process A process B
------------------- ---------------
1.kstrdup last_cmd
2.free last_cmd
3.tracing_log_err(use-after-free)
================================================================
Appendix 1. KASAN report double-free:
BUG: KASAN: double-free in kfree+0xdc/0x1d4
Free of addr ***** by task sh/4879
Call trace:
...
kfree+0xdc/0x1d4
create_or_delete_synth_event+0x60/0x1e8
trace_parse_run_command+0x2bc/0x4b8
synth_events_write+0x20/0x30
vfs_write+0x200/0x830
...
Allocated by task 4879:
...
kstrdup+0x5c/0x98
create_or_delete_synth_event+0x6c/0x1e8
trace_parse_run_command+0x2bc/0x4b8
synth_events_write+0x20/0x30
vfs_write+0x200/0x830
...
Freed by task 5464:
...
kfree+0xdc/0x1d4
create_or_delete_synth_event+0x60/0x1e8
trace_parse_run_command+0x2bc/0x4b8
synth_events_write+0x20/0x30
vfs_write+0x200/0x830
...
================================================================
Appendix 2. KASAN report use-after-free:
BUG: KASAN: use-after-free in strlen+0x5c/0x7c
Read of size 1 at addr ***** by task sh/5483
sh: CPU: 7 PID: 5483 Comm: sh
...
__asan_report_load1_noabort+0x34/0x44
strlen+0x5c/0x7c
tracing_log_err+0x60/0x444
create_or_delete_synth_event+0xc4/0x204
trace_parse_run_command+0x2bc/0x4b8
synth_events_write+0x20/0x30
vfs_write+0x200/0x830
...
Allocated by task 5483:
...
kstrdup+0x5c/0x98
create_or_delete_synth_event+0x80/0x204
trace_parse_run_command+0x2bc/0x4b8
synth_events_write+0x20/0x30
vfs_write+0x200/0x830
...
Freed by task 5480:
...
kfree+0xdc/0x1d4
create_or_delete_synth_event+0x74/0x204
trace_parse_run_command+0x2bc/0x4b8
synth_events_write+0x20/0x30
vfs_write+0x200/0x830
...
Link: https://lore.kernel.org/linux-trace-kernel/20230321110444.1587-1-Tze-nan.Wu@mediatek.com
Fixes:
27c888da9867 ("tracing: Remove size restriction on synthetic event cmd error logging")
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: "Tom Zanussi" <zanussi@kernel.org>
Signed-off-by: Tze-nan Wu <Tze-nan.Wu@mediatek.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Song Yoong Siang [Tue, 4 Apr 2023 04:48:23 +0000 (12:48 +0800)]
net: stmmac: Add queue reset into stmmac_xdp_open() function
commit
24e3fce00c0b557491ff596c0682a29dee6fe848 upstream.
Queue reset was moved out from __init_dma_rx_desc_rings() and
__init_dma_tx_desc_rings() functions. Thus, the driver fails to transmit
and receive packet after XDP prog setup.
This commit adds the missing queue reset into stmmac_xdp_open() function.
Fixes:
f9ec5723c3db ("net: ethernet: stmicro: stmmac: move queue reset to dedicated functions")
Cc: <stable@vger.kernel.org> # 6.0+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230404044823.3226144-1-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 4 Apr 2023 11:02:49 +0000 (13:02 +0200)]
ACPI: video: Add acpi_backlight=video quirk for Lenovo ThinkPad W530
commit
a5b2781dcab2c77979a4b8adda781d2543580901 upstream.
The Lenovo ThinkPad W530 uses a nvidia k1000m GPU. When this gets used
together with one of the older nvidia binary driver series (the latest
series does not support it), then backlight control does not work.
This is caused by commit
3dbc80a3e4c5 ("ACPI: video: Make backlight
class device registration a separate step (v2)") combined with
commit
5aa9d943e9b6 ("ACPI: video: Don't enable fallback path for
creating ACPI backlight by default").
After these changes the acpi_video# backlight device is only registered
when requested by a GPU driver calling acpi_video_register_backlight()
which the nvidia binary driver does not do.
I realize that using the nvidia binary driver is not a supported use-case
and users can workaround this by adding acpi_backlight=video on the kernel
commandline, but the ThinkPad W530 is a popular model under Linux users,
so it seems worthwhile to add a quirk for this.
I will also email Nvidia asking them to make the driver call
acpi_video_register_backlight() when an internal LCD panel is detected.
So maybe the next maintenance release of the drivers will fix this...
Fixes:
5aa9d943e9b6 ("ACPI: video: Don't enable fallback path for creating ACPI backlight by default")
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 4 Apr 2023 11:02:48 +0000 (13:02 +0200)]
ACPI: video: Add acpi_backlight=video quirk for Apple iMac14,1 and iMac14,2
commit
2699107989431d6db44f8a9e809ea74c387336d1 upstream.
On the Apple iMac14,1 and iMac14,2 all-in-ones (monitors with builtin "PC")
the connection between the GPU and the panel is seen by the GPU driver as
regular DP instead of eDP, causing the GPU driver to never call
acpi_video_register_backlight().
(GPU drivers only call acpi_video_register_backlight() when an internal
panel is detected, to avoid non working acpi_video# devices getting
registered on desktops which unfortunately is a real issue.)
Fix the missing acpi_video# backlight device on these all-in-ones by
adding a acpi_backlight=video DMI quirk, so that video.ko will
immediately register the backlight device instead of waiting for
an acpi_video_register_backlight() call.
Fixes:
5aa9d943e9b6 ("ACPI: video: Don't enable fallback path for creating ACPI backlight by default")
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 4 Apr 2023 11:02:47 +0000 (13:02 +0200)]
ACPI: video: Make acpi_backlight=video work independent from GPU driver
commit
e506731c8f35699d746c615164ed620cd53c00ca upstream.
Commit
3dbc80a3e4c5 ("ACPI: video: Make backlight class device
registration a separate step (v2)") combined with
commit
5aa9d943e9b6 ("ACPI: video: Don't enable fallback path for
creating ACPI backlight by default")
Means that the video.ko code now fully depends on the GPU driver calling
acpi_video_register_backlight() for the acpi_video# backlight class
devices to get registered.
This means that if the GPU driver does not do this, acpi_backlight=video
on the cmdline, or DMI quirks for selecting acpi_video# will not work.
This is a problem on for example Apple iMac14,1 all-in-ones where
the monitor's LCD panel shows up as a regular DP connection instead of
eDP so the GPU driver will not call acpi_video_register_backlight() [1].
Fix this by making video.ko directly register the acpi_video# devices
when these have been explicitly requested either on the cmdline or
through DMI quirks (rather then auto-detection being used).
[1] GPU drivers only call acpi_video_register_backlight() when an internal
panel is detected, to avoid non working acpi_video# devices getting
registered on desktops which unfortunately is a real issue.
Fixes:
5aa9d943e9b6 ("ACPI: video: Don't enable fallback path for creating ACPI backlight by default")
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Tue, 4 Apr 2023 11:02:46 +0000 (13:02 +0200)]
ACPI: video: Add auto_detect arg to __acpi_video_get_backlight_type()
commit
78dfc9d1d1abb9e400386fa9c5724a8f7d75e3b9 upstream.
Allow callers of __acpi_video_get_backlight_type() to pass a pointer
to a bool which will get set to false if the backlight-type comes from
the cmdline or a DMI quirk and set to true if auto-detection was used.
And make __acpi_video_get_backlight_type() non static so that it can
be called directly outside of video_detect.c .
While at it turn the acpi_video_get_backlight_type() and
acpi_video_backlight_use_native() wrappers into static inline functions
in include/acpi/video.h, so that we need to export one less symbol.
Fixes:
5aa9d943e9b6 ("ACPI: video: Don't enable fallback path for creating ACPI backlight by default")
Cc: All applicable <stable@vger.kernel.org>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Hartkopp [Thu, 30 Mar 2023 17:02:48 +0000 (19:02 +0200)]
can: isotp: isotp_recvmsg(): use sock_recv_cmsgs() to get SOCK_RXQ_OVFL infos
commit
0145462fc802cd447ef5d029758043c7f15b4b1e upstream.
isotp.c was still using sock_recv_timestamp() which does not provide
control messages to detect dropped PDUs in the receive path.
Fixes:
e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230330170248.62342-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Sojka [Fri, 31 Mar 2023 12:55:11 +0000 (14:55 +0200)]
can: isotp: isotp_ops: fix poll() to not report false EPOLLOUT events
commit
79e19fa79cb5d5f1b3bf3e3ae24989ccb93c7b7b upstream.
When using select()/poll()/epoll() with a non-blocking ISOTP socket to
wait for when non-blocking write is possible, a false EPOLLOUT event
is sometimes returned. This can happen at least after sending a
message which must be split to multiple CAN frames.
The reason is that isotp_sendmsg() returns -EAGAIN when tx.state is
not equal to ISOTP_IDLE and this behavior is not reflected in
datagram_poll(), which is used in isotp_ops.
This is fixed by introducing ISOTP-specific poll function, which
suppresses the EPOLLOUT events in that case.
v2: https://lore.kernel.org/all/
20230302092812.320643-1-michal.sojka@cvut.cz
v1: https://lore.kernel.org/all/
20230224010659.48420-1-michal.sojka@cvut.cz
https://lore.kernel.org/all/
b53a04a2-ba1f-3858-84c1-
d3eb3301ae15@hartkopp.net
Signed-off-by: Michal Sojka <michal.sojka@cvut.cz>
Reported-by: Jakub Jira <jirajak2@fel.cvut.cz>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes:
e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol")
Link: https://lore.kernel.org/all/20230331125511.372783-1-michal.sojka@cvut.cz
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Hartkopp [Fri, 31 Mar 2023 13:19:35 +0000 (15:19 +0200)]
can: isotp: fix race between isotp_sendsmg() and isotp_release()
commit
051737439eaee5bdd03d3c2ef5510d54a478fd05 upstream.
As discussed with Dae R. Jeong and Hillf Danton here [1] the sendmsg()
function in isotp.c might get into a race condition when restoring the
former tx.state from the old_state.
Remove the old_state concept and implement proper locking for the
ISOTP_IDLE transitions in isotp_sendmsg(), inspired by a
simplification idea from Hillf Danton.
Introduce a new tx.state ISOTP_SHUTDOWN and use the same locking
mechanism from isotp_release() which resolves a potential race between
isotp_sendsmg() and isotp_release().
[1] https://lore.kernel.org/linux-can/ZB%2F93xJxq%2FBUqAgG@dragonet
v1: https://lore.kernel.org/all/
20230331102114.15164-1-socketcan@hartkopp.net
v2: https://lore.kernel.org/all/
20230331123600.3550-1-socketcan@hartkopp.net
take care of signal interrupts for wait_event_interruptible() in
isotp_release()
v3: https://lore.kernel.org/all/
20230331130654.9886-1-socketcan@hartkopp.net
take care of signal interrupts for wait_event_interruptible() in
isotp_sendmsg() in the wait_tx_done case
v4: https://lore.kernel.org/all/
20230331131935.21465-1-socketcan@hartkopp.net
take care of signal interrupts for wait_event_interruptible() in
isotp_sendmsg() in ALL cases
Cc: Dae R. Jeong <threeearcat@gmail.com>
Cc: Hillf Danton <hdanton@sina.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes:
4f027cba8216 ("can: isotp: split tx timer into transmission and timeout")
Link: https://lore.kernel.org/all/20230331131935.21465-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
[mkl: rephrase commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksij Rempel [Tue, 4 Apr 2023 07:31:28 +0000 (09:31 +0200)]
can: j1939: j1939_tp_tx_dat_new(): fix out-of-bounds memory access
commit
b45193cb4df556fe6251b285a5ce44046dd36b4a upstream.
In the j1939_tp_tx_dat_new() function, an out-of-bounds memory access
could occur during the memcpy() operation if the size of skb->cb is
larger than the size of struct j1939_sk_buff_cb. This is because the
memcpy() operation uses the size of skb->cb, leading to a read beyond
the struct j1939_sk_buff_cb.
Updated the memcpy() operation to use the size of struct
j1939_sk_buff_cb instead of the size of skb->cb. This ensures that the
memcpy() operation only reads the memory within the bounds of struct
j1939_sk_buff_cb, preventing out-of-bounds memory access.
Additionally, add a BUILD_BUG_ON() to check that the size of skb->cb
is greater than or equal to the size of struct j1939_sk_buff_cb. This
ensures that the skb->cb buffer is large enough to hold the
j1939_sk_buff_cb structure.
Fixes:
9d71dd0c7009 ("can: add support of SAE J1939 protocol")
Reported-by: Shuangpeng Bai <sjb7183@psu.edu>
Tested-by: Shuangpeng Bai <sjb7183@psu.edu>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://groups.google.com/g/syzkaller/c/G_LL-C3plRs/m/-8xCi6dCAgAJ
Link: https://lore.kernel.org/all/20230404073128.3173900-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
[mkl: rephrase commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Brauner [Thu, 30 Mar 2023 07:13:16 +0000 (09:13 +0200)]
fs: drop peer group ids under namespace lock
commit
cb2239c198ad9fbd5aced22cf93e45562da781eb upstream.
When cleaning up peer group ids in the failure path we need to make sure
to hold on to the namespace lock. Otherwise another thread might just
turn the mount from a shared into a non-shared mount concurrently.
Link: https://lore.kernel.org/lkml/00000000000088694505f8132d77@google.com
Fixes:
2a1867219c7b ("fs: add mount_setattr()")
Reported-by: syzbot+8ac3859139c685c4f597@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # 5.12+
Message-Id: <
20230330-vfs-mount_setattr-propagation-fix-v1-1-
37548d91533b@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zheng Yejian [Thu, 30 Mar 2023 02:52:23 +0000 (10:52 +0800)]
ftrace: Fix issue that 'direct->addr' not restored in modify_ftrace_direct()
commit
2a2d8c51defb446e8d89a83f42f8e5cd529111e9 upstream.
Syzkaller report a WARNING: "WARN_ON(!direct)" in modify_ftrace_direct().
Root cause is 'direct->addr' was changed from 'old_addr' to 'new_addr' but
not restored if error happened on calling ftrace_modify_direct_caller().
Then it can no longer find 'direct' by that 'old_addr'.
To fix it, restore 'direct->addr' to 'old_addr' explicitly in error path.
Link: https://lore.kernel.org/linux-trace-kernel/20230330025223.1046087-1-zhengyejian1@huawei.com
Cc: stable@vger.kernel.org
Cc: <mhiramat@kernel.org>
Cc: <mark.rutland@arm.com>
Cc: <ast@kernel.org>
Cc: <daniel@iogearbox.net>
Fixes:
8a141dd7f706 ("ftrace: Fix modify_ftrace_direct.")
Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John Keeping [Mon, 27 Mar 2023 17:36:46 +0000 (18:36 +0100)]
ftrace: Mark get_lock_parent_ip() __always_inline
commit
ea65b41807a26495ff2a73dd8b1bab2751940887 upstream.
If the compiler decides not to inline this function then preemption
tracing will always show an IP inside the preemption disabling path and
never the function actually calling preempt_{enable,disable}.
Link: https://lore.kernel.org/linux-trace-kernel/20230327173647.1690849-1-john@metanate.com
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: stable@vger.kernel.org
Fixes:
f904f58263e1d ("sched/debug: Fix preempt_disable_ip recording for preempt_disable()")
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kan Liang [Wed, 22 Mar 2023 20:24:49 +0000 (13:24 -0700)]
perf/core: Fix the same task check in perf_event_set_output
[ Upstream commit
24d3ae2f37d8bc3c14b31d353c5d27baf582b6a6 ]
The same task check in perf_event_set_output has some potential issues
for some usages.
For the current perf code, there is a problem if using of
perf_event_open() to have multiple samples getting into the same mmap’d
memory when they are both attached to the same process.
https://lore.kernel.org/all/
92645262-D319-4068-9C44-
2409EF44888E@gmail.com/
Because the event->ctx is not ready when the perf_event_set_output() is
invoked in the perf_event_open().
Besides the above issue, before the commit
bd2756811766 ("perf: Rewrite
core context handling"), perf record can errors out when sampling with
a hardware event and a software event as below.
$ perf record -e cycles,dummy --per-thread ls
failed to mmap with 22 (Invalid argument)
That's because that prior to the commit a hardware event and a software
event are from different task context.
The problem should be a long time issue since commit
c3f00c70276d
("perk: Separate find_get_context() from event initialization").
The task struct is stored in the event->hw.target for each per-thread
event. It is a more reliable way to determine whether two events are
attached to the same task.
The event->hw.target was also introduced several years ago by the
commit
50f16a8bf9d7 ("perf: Remove type specific target pointers"). It
can not only be used to fix the issue with the current code, but also
back port to fix the issues with an older kernel.
Note: The event->hw.target was introduced later than commit
c3f00c70276d. The patch may cannot be applied between the commit
c3f00c70276d and commit
50f16a8bf9d7. Anybody that wants to back-port
this at that period may have to find other solutions.
Fixes:
c3f00c70276d ("perf: Separate find_get_context() from event initialization")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Link: https://lkml.kernel.org/r/20230322202449.512091-1-kan.liang@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yu Kuai [Wed, 22 Mar 2023 03:59:26 +0000 (11:59 +0800)]
block: don't set GD_NEED_PART_SCAN if scan partition failed
[ Upstream commit
3723091ea1884d599cc8b8bf719d6f42e8d4d8b1 ]
Currently if disk_scan_partitions() failed, GD_NEED_PART_SCAN will still
set, and partition scan will be proceed again when blkdev_get_by_dev()
is called. However, this will cause a problem that re-assemble partitioned
raid device will creat partition for underlying disk.
Test procedure:
mdadm -CR /dev/md0 -l 1 -n 2 /dev/sda /dev/sdb -e 1.0
sgdisk -n 0:0:+100MiB /dev/md0
blockdev --rereadpt /dev/sda
blockdev --rereadpt /dev/sdb
mdadm -S /dev/md0
mdadm -A /dev/md0 /dev/sda /dev/sdb
Test result: underlying disk partition and raid partition can be
observed at the same time
Note that this can still happen in come corner cases that
GD_NEED_PART_SCAN can be set for underlying disk while re-assemble raid
device.
Fixes:
e5cfefa97bcc ("block: fix scan partition for exclusively open device again")
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ming Lei [Thu, 6 Apr 2023 12:40:59 +0000 (20:40 +0800)]
block: ublk: make sure that block size is set correctly
[ Upstream commit
1d1665279a845d16c93687389e364386e3fe0f38 ]
block size is one very key setting for block layer, and bad block size
could panic kernel easily.
Make sure that block size is set correctly.
Meantime if ublk_validate_params() fails, clear ub->params so that disk
is prevented from being added.
Fixes:
71f28f3136af ("ublk_drv: add io_uring based userspace block driver")
Reported-and-tested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thiago Rafael Becker [Wed, 5 Apr 2023 13:16:48 +0000 (10:16 -0300)]
cifs: sanitize paths in cifs_update_super_prepath.
[ Upstream commit
d19342c6609b67f2ba83b9eccca2777e3687f625 ]
After a server reboot, clients are failing to move files with ENOENT.
This is caused by DFS referrals containing multiple separators, which
the server move call doesn't recognize.
v1: Initial patch.
v2: Move prototype to header.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2182472
Fixes:
a31080899d5f ("cifs: sanitize multiple delimiters in prepath")
Actually-Fixes:
24e0a1eff9e2 ("cifs: switch to new mount api")
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Thiago Rafael Becker <tbecker@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Keith Busch [Mon, 3 Apr 2023 20:09:25 +0000 (13:09 -0700)]
nvme: fix discard support without oncs
[ Upstream commit
d3205ab75e99a47539ec91ef85ba488f4ddfeaa9 ]
The device can report discard support without setting the ONCS DSM bit.
When not set, the driver clears max_discard_size expecting it to be set
later. We don't know the size until we have the namespace format,
though, so setting it is deferred until configuring one, but the driver
was abandoning the discard settings due to that initial clearing.
Move the max_discard_size calculation above the check for a '0' discard
size.
Fixes:
1a86924e4f46475 ("nvme: fix interpretation of DMRSL")
Reported-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Zhong Jinghua [Wed, 29 Mar 2023 07:17:39 +0000 (15:17 +0800)]
scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
[ Upstream commit
48b19b79cfa37b1e50da3b5a8af529f994c08901 ]
The validity of sock should be checked before assignment to avoid incorrect
values. Commit
57569c37f0ad ("scsi: iscsi: iscsi_tcp: Fix null-ptr-deref
while calling getpeername()") introduced this change which may lead to
inconsistent values of tcp_sw_conn->sendpage and conn->datadgst_en.
Fix the issue by moving the position of the assignment.
Fixes:
57569c37f0ad ("scsi: iscsi: iscsi_tcp: Fix null-ptr-deref while calling getpeername()")
Signed-off-by: Zhong Jinghua <zhongjinghua@huawei.com>
Link: https://lore.kernel.org/r/20230329071739.2175268-1-zhongjinghua@huaweicloud.com
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Li Zetao [Sat, 25 Mar 2023 11:00:04 +0000 (11:00 +0000)]
scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
[ Upstream commit
85ade4010e13ef152ea925c74d94253db92e5428 ]
There is a memory leak reported by kmemleak:
unreferenced object 0xffffc900003f0000 (size 12288):
comm "modprobe", pid 19117, jiffies
4299751452 (age 42490.264s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
00000000629261a8>] __vmalloc_node_range+0xe56/0x1110
[<
0000000001906886>] __vmalloc_node+0xbd/0x150
[<
000000005bb4dc34>] vmalloc+0x25/0x30
[<
00000000a2dc1194>] qla2x00_create_host+0x7a0/0xe30 [qla2xxx]
[<
0000000062b14b47>] qla2x00_probe_one+0x2eb8/0xd160 [qla2xxx]
[<
00000000641ccc04>] local_pci_probe+0xeb/0x1a0
The root cause is traced to an error-handling path in qla2x00_probe_one()
when the adapter "base_vha" initialize failed. The fab_scan_rp "scan.l" is
used to record the port information and it is allocated in
qla2x00_create_host(). However, it is not released in the error handling
path "probe_failed".
Fix this by freeing the memory of "scan.l" when an error occurs in the
adapter initialization process.
Fixes:
a4239945b8ad ("scsi: qla2xxx: Add switch command to simplify fabric discovery")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230325110004.363898-1-lizetao1@huawei.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wojciech Lukowicz [Sat, 1 Apr 2023 19:50:39 +0000 (20:50 +0100)]
io_uring: fix memory leak when removing provided buffers
[ Upstream commit
b4a72c0589fdea6259720375426179888969d6a2 ]
When removing provided buffers, io_buffer structs are not being disposed
of, leading to a memory leak. They can't be freed individually, because
they are allocated in page-sized groups. They need to be added to some
free list instead, such as io_buffers_cache. All callers already hold
the lock protecting it, apart from when destroying buffers, so had to
extend the lock there.
Fixes:
cc3cec8367cb ("io_uring: speedup provided buffer handling")
Signed-off-by: Wojciech Lukowicz <wlukowicz01@gmail.com>
Link: https://lore.kernel.org/r/20230401195039.404909-2-wlukowicz01@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Wojciech Lukowicz [Sat, 1 Apr 2023 19:50:38 +0000 (20:50 +0100)]
io_uring: fix return value when removing provided buffers
[ Upstream commit
c0921e51dab767ef5adf6175c4a0ba3c6e1074a3 ]
When a request to remove buffers is submitted, and the given number to be
removed is larger than available in the specified buffer group, the
resulting CQE result will be the number of removed buffers + 1, which is
1 more than it should be.
Previously, the head was part of the list and it got removed after the
loop, so the increment was needed. Now, the head is not an element of
the list, so the increment shouldn't be there anymore.
Fixes:
dbc7d452e7cf ("io_uring: manage provided buffers strictly ordered")
Signed-off-by: Wojciech Lukowicz <wlukowicz01@gmail.com>
Link: https://lore.kernel.org/r/20230401195039.404909-2-wlukowicz01@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nuno Sá [Fri, 20 Jan 2023 12:46:45 +0000 (13:46 +0100)]
iio: adc: ad7791: fix IRQ flags
[ Upstream commit
0c6ef985a1fd8a74dcb5cad941ddcadd55cb8697 ]
The interrupt is triggered on the falling edge rather than being a level
low interrupt.
Fixes:
da4d3d6bb9f6 ("iio: adc: ad-sigma-delta: Allow custom IRQ flags")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230120124645.819910-1-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Keith Busch [Fri, 31 Mar 2023 18:00:56 +0000 (11:00 -0700)]
blk-mq: directly poll requests
commit
38a8c4d1d45006841f0643f4cb29b5e50758837c upstream.
Polling needs a bio with a valid bi_bdev, but neither of those are
guaranteed for polled driver requests. Make request based polling
directly use blk-mq's polling function instead.
When executing a request from a polled hctx, we know the request's
cookie, and that it's from a live blk-mq queue that supports polling, so
we can safely skip everything that bio_poll provides.
Cc: stable@kernel.org
Reported-by: Martin Belanger <Martin.Belanger@dell.com>
Reported-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Tested-by: Daniel Wagner <dwagner@suse.de>
Revieded-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20230331180056.1155862-1-kbusch@meta.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
William Breathitt Gray [Thu, 16 Mar 2023 20:34:26 +0000 (16:34 -0400)]
counter: 104-quad-8: Fix Synapse action reported for Index signals
commit
00f4bc5184c19cb33f468f1ea409d70d19f8f502 upstream.
Signal 16 and higher represent the device's Index lines. The
priv->preset_enable array holds the device configuration for these Index
lines. The preset_enable configuration is active low on the device, so
invert the conditional check in quad8_action_read() to properly handle
the logical state of preset_enable.
Fixes:
f1d8a071d45b ("counter: 104-quad-8: Add Generic Counter interface support")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230316203426.224745-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
William Breathitt Gray [Sun, 12 Mar 2023 23:15:49 +0000 (19:15 -0400)]
counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
commit
4aa3b75c74603c3374877d5fd18ad9cc3a9a62ed upstream.
The Counter (CNTR) register is 24 bits wide, but we can have an
effective 25-bit count value by setting bit 24 to the XOR of the Borrow
flag and Carry flag. The flags can be read from the FLAG register, but a
race condition exists: the Borrow flag and Carry flag are instantaneous
and could change by the time the count value is read from the CNTR
register.
Since the race condition could result in an incorrect 25-bit count
value, remove support for 25-bit count values from this driver;
hard-coded maximum count values are replaced by a LS7267_CNTR_MAX define
for consistency and clarity.
Fixes:
28e5d3bb0325 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Cc: <stable@vger.kernel.org> # 6.1.x
Cc: <stable@vger.kernel.org> # 6.2.x
Link: https://lore.kernel.org/r/20230312231554.134858-1-william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve Clevenger [Mon, 27 Feb 2023 23:54:32 +0000 (16:54 -0700)]
coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
commit
bf84937e882009075f57fd213836256fc65d96bc upstream.
In etm4_enable_hw, fix for() loop range to represent address comparator pairs.
Fixes:
2e1cdfe184b5 ("coresight-etm4x: Adding CoreSight ETM4x driver")
Cc: stable@vger.kernel.org
Signed-off-by: Steve Clevenger <scclevenger@os.amperecomputing.com>
Reviewed-by: James Clark <james.clark@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/4a4ee61ce8ef402615a4528b21a051de3444fb7b.1677540079.git.scclevenger@os.amperecomputing.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose [Tue, 21 Mar 2023 10:45:30 +0000 (10:45 +0000)]
coresight: etm4x: Do not access TRCIDR1 for identification
commit
735e7b30a53a1679c050cddb73f5e5316105d2e3 upstream.
CoreSight ETM4x architecture clearly provides ways to identify a device
via registers in the "Management" class, TRCDEVARCH and TRCDEVTYPE. These
registers can be accessed without the Trace domain being powered on.
We additionally added TRCIDR1 as fallback in order to cover for any
ETMs that may not have implemented TRCDEVARCH. So far, nobody has
reported hitting a WARNING we placed to catch such systems.
Also, more importantly it is problematic to access TRCIDR1, which is a
"Trace" register via MMIO access, without clearing the OSLK. But we cannot
mess with the OSLK until we know for sure that this is an ETMv4 device.
Thus, this kind of creates a chicken and egg problem unnecessarily for
systems "which are compliant" to the ETMv4 architecture.
Let us remove the TRCIDR1 fall back check and rely only on TRCDEVARCH.
Fixes:
8b94db1edaee ("coresight: etm4x: Use TRCDEVARCH for component discovery")
Cc: stable@vger.kernel.org
Reported-by: Steve Clevenger <scclevenger@os.amperecomputing.com>
Link: https://lore.kernel.org/all/143540e5623d4c7393d24833f2b80600d8d745d2.1677881753.git.scclevenger@os.amperecomputing.com/
Cc: Mike Leach <mike.leach@linaro.org>
Cc: James Clark <james.clark@arm.com>
Reviewed-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230321104530.1547136-1-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Muchun Song [Thu, 23 Mar 2023 02:50:03 +0000 (10:50 +0800)]
mm: kfence: fix handling discontiguous page
commit
1f2803b2660f4b04d48d065072c0ae0c9ca255fd upstream.
The struct pages could be discontiguous when the kfence pool is allocated
via alloc_contig_pages() with CONFIG_SPARSEMEM and
!CONFIG_SPARSEMEM_VMEMMAP.
This may result in setting PG_slab and memcg_data to a arbitrary
address (may be not used as a struct page), which in the worst case
might corrupt the kernel.
So the iteration should use nth_page().
Link: https://lkml.kernel.org/r/20230323025003.94447-1-songmuchun@bytedance.com
Fixes:
0ce20dd84089 ("mm: add Kernel Electric-Fence infrastructure")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Marco Elver <elver@google.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: SeongJae Park <sjpark@amazon.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Muchun Song [Mon, 20 Mar 2023 03:00:59 +0000 (11:00 +0800)]
mm: kfence: fix PG_slab and memcg_data clearing
commit
3ee2d7471fa4963a2ced0a84f0653ce88b43c5b2 upstream.
It does not reset PG_slab and memcg_data when KFENCE fails to initialize
kfence pool at runtime. It is reporting a "Bad page state" message when
kfence pool is freed to buddy. The checking of whether it is a compound
head page seems unnecessary since we already guarantee this when
allocating kfence pool. Remove the check to simplify the code.
Link: https://lkml.kernel.org/r/20230320030059.20189-1-songmuchun@bytedance.com
Fixes:
0ce20dd84089 ("mm: add Kernel Electric-Fence infrastructure")
Signed-off-by: Muchun Song <songmuchun@bytedance.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Jann Horn <jannh@google.com>
Cc: Marco Elver <elver@google.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sjpark@amazon.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Wed, 22 Mar 2023 14:33:00 +0000 (07:33 -0700)]
KVM: nVMX: Do not report error code when synthesizing VM-Exit from Real Mode
commit
80962ec912db56d323883154efc2297473e692cb upstream.
Don't report an error code to L1 when synthesizing a nested VM-Exit and
L2 is in Real Mode. Per Intel's SDM, regarding the error code valid bit:
This bit is always 0 if the VM exit occurred while the logical processor
was in real-address mode (CR0.PE=0).
The bug was introduced by a recent fix for AMD's Paged Real Mode, which
moved the error code suppression from the common "queue exception" path
to the "inject exception" path, but missed VMX's "synthesize VM-Exit"
path.
Fixes:
b97f07458373 ("KVM: x86: determine if an exception has an error code only when injecting it.")
Cc: stable@vger.kernel.org
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20230322143300.2209476-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sean Christopherson [Wed, 22 Mar 2023 14:32:59 +0000 (07:32 -0700)]
KVM: x86: Clear "has_error_code", not "error_code", for RM exception injection
commit
6c41468c7c12d74843bb414fc00307ea8a6318c3 upstream.
When injecting an exception into a vCPU in Real Mode, suppress the error
code by clearing the flag that tracks whether the error code is valid, not
by clearing the error code itself. The "typo" was introduced by recent
fix for SVM's funky Paged Real Mode.
Opportunistically hoist the logic above the tracepoint so that the trace
is coherent with respect to what is actually injected (this was also the
behavior prior to the buggy commit).
Fixes:
b97f07458373 ("KVM: x86: determine if an exception has an error code only when injecting it.")
Cc: stable@vger.kernel.org
Cc: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <
20230322143300.2209476-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mario Limonciello [Wed, 29 Mar 2023 17:45:35 +0000 (12:45 -0500)]
x86/ACPI/boot: Use FADT version to check support for online capable
commit
a74fabfbd1b7013045afc8cc541e6cab3360ccb5 upstream.
ACPI 6.3 introduced the online capable bit, and also introduced MADT
version 5.
Latter was used to distinguish whether the offset storing online capable
could be used. However ACPI 6.2b has MADT version "45" which is for
an errata version of the ACPI 6.2 spec. This means that the Linux code
for detecting availability of MADT will mistakenly flag ACPI 6.2b as
supporting online capable which is inaccurate as it's an ACPI 6.3 feature.
Instead use the FADT major and minor revision fields to distinguish this.
[ bp: Massage. ]
Fixes:
aa06e20f1be6 ("x86/ACPI: Don't add CPUs that are not online capable")
Reported-by: Eric DeVolder <eric.devolder@oracle.com>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/943d2445-84df-d939-f578-5d8240d342cc@unsolicited.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric DeVolder [Mon, 27 Mar 2023 19:10:26 +0000 (15:10 -0400)]
x86/acpi/boot: Correct acpi_is_processor_usable() check
commit
fed8d8773b8ea68ad99d9eee8c8343bef9da2c2c upstream.
The logic in acpi_is_processor_usable() requires the online capable
bit be set for hotpluggable CPUs. The online capable bit has been
introduced in ACPI 6.3.
However, for ACPI revisions < 6.3 which do not support that bit, CPUs
should be reported as usable, not the other way around.
Reverse the check.
[ bp: Rewrite commit message. ]
Fixes:
e2869bd7af60 ("x86/acpi/boot: Do not register processors that cannot be onlined for x2APIC")
Suggested-by: Miguel Luis <miguel.luis@oracle.com>
Suggested-by: Boris Ostrovsky <boris.ovstrosky@oracle.com>
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: David R <david@unsolicited.net>
Cc: <stable@kernel.org>
Link: https://lore.kernel.org/r/20230327191026.3454-2-eric.devolder@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Chi [Fri, 31 Mar 2023 08:32:41 +0000 (16:32 +0800)]
ALSA: hda/realtek: fix mute/micmute LEDs for a HP ProBook
commit
9fdc1605c504204e0fdec7892b29c916579e06f3 upstream.
There is a HP ProBook which using ALC236 codec and need the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED and
micmute LED work.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230331083242.58416-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeremy Soller [Fri, 31 Mar 2023 16:23:17 +0000 (10:23 -0600)]
ALSA: hda/realtek: Add quirk for Clevo X370SNW
commit
36d4d213c6d4fffae2645a601e8ae996de4c3645 upstream.
Fixes speaker output and headset detection on Clevo X370SNW.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230331162317.14992-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Namjae Jeon [Sat, 1 Apr 2023 04:21:04 +0000 (13:21 +0900)]
ksmbd: fix slab-out-of-bounds in init_smb2_rsp_hdr
commit
dc8289f912387c3bcfbc5d2db29c8947fa207c11 upstream.
When smb1 mount fails, KASAN detect slab-out-of-bounds in
init_smb2_rsp_hdr like the following one.
For smb1 negotiate(56bytes) , init_smb2_rsp_hdr() for smb2 is called.
The issue occurs while handling smb1 negotiate as smb2 server operations.
Add smb server operations for smb1 (get_cmd_val, init_rsp_hdr,
allocate_rsp_buf, check_user_session) to handle smb1 negotiate so that
smb2 server operation does not handle it.
[ 411.400423] CIFS: VFS: Use of the less secure dialect vers=1.0 is
not recommended unless required for access to very old servers
[ 411.400452] CIFS: Attempting to mount \\192.168.45.139\homes
[ 411.479312] ksmbd: init_smb2_rsp_hdr : 492
[ 411.479323] ==================================================================
[ 411.479327] BUG: KASAN: slab-out-of-bounds in
init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479369] Read of size 16 at addr
ffff888488ed0734 by task kworker/14:1/199
[ 411.479379] CPU: 14 PID: 199 Comm: kworker/14:1 Tainted: G
OE 6.1.21 #3
[ 411.479386] Hardware name: ASUSTeK COMPUTER INC. Z10PA-D8
Series/Z10PA-D8 Series, BIOS 3801 08/23/2019
[ 411.479390] Workqueue: ksmbd-io handle_ksmbd_work [ksmbd]
[ 411.479425] Call Trace:
[ 411.479428] <TASK>
[ 411.479432] dump_stack_lvl+0x49/0x63
[ 411.479444] print_report+0x171/0x4a8
[ 411.479452] ? kasan_complete_mode_report_info+0x3c/0x200
[ 411.479463] ? init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479497] kasan_report+0xb4/0x130
[ 411.479503] ? init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479537] kasan_check_range+0x149/0x1e0
[ 411.479543] memcpy+0x24/0x70
[ 411.479550] init_smb2_rsp_hdr+0x1e2/0x1f4 [ksmbd]
[ 411.479585] handle_ksmbd_work+0x109/0x760 [ksmbd]
[ 411.479616] ? _raw_spin_unlock_irqrestore+0x50/0x50
[ 411.479624] ? smb3_encrypt_resp+0x340/0x340 [ksmbd]
[ 411.479656] process_one_work+0x49c/0x790
[ 411.479667] worker_thread+0x2b1/0x6e0
[ 411.479674] ? process_one_work+0x790/0x790
[ 411.479680] kthread+0x177/0x1b0
[ 411.479686] ? kthread_complete_and_exit+0x30/0x30
[ 411.479692] ret_from_fork+0x22/0x30
[ 411.479702] </TASK>
Fixes:
39b291b86b59 ("ksmbd: return unsupported error on smb1 mount")
Cc: stable@vger.kernel.org
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marios Makassikis [Thu, 16 Mar 2023 13:40:43 +0000 (14:40 +0100)]
ksmbd: do not call kvmalloc() with __GFP_NORETRY | __GFP_NO_WARN
commit
e416ea62a9166e6075a07a970cc5bf79255d2700 upstream.
Commit
83dcedd5540d ("ksmbd: fix infinite loop in ksmbd_conn_handler_loop()"),
changes GFP modifiers passed to kvmalloc(). This cause xfstests generic/551
test to fail. We limit pdu length size according to connection status and
maximum number of connections. In the rest, memory allocation of request
is limited by credit management. so these flags are no longer needed.
Fixes:
83dcedd5540d ("ksmbd: fix infinite loop in ksmbd_conn_handler_loop()")
Cc: stable@vger.kernel.org
Signed-off-by: Marios Makassikis <mmakassikis@freebox.fr>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilpo Järvinen [Fri, 17 Mar 2023 10:30:34 +0000 (12:30 +0200)]
serial: 8250: Prevent starting up DMA Rx on THRI interrupt
commit
90b8596ac46043e4a782d9111f5b285251b13756 upstream.
Hans de Goede reported Bluetooth adapters (HCIs) connected over an UART
connection failed due corrupted Rx payload. The problem was narrowed
down to DMA Rx starting on UART_IIR_THRI interrupt. The problem occurs
despite LSR having DR bit set, which is precondition for attempting to
start DMA Rx in the first place.
From a debug patch:
[x.807834] 8250irq: iir=cc lsr+saved=60 received=0/15 ier=0f dma_t/rx/err=0/0/0
[x.808676] 8250irq: iir=c2 lsr+saved=61 received=0/0 ier=0f dma_t/rx/err=0/0/0
[x.808776] 8250irq: iir=cc lsr+saved=60 received=1/12 ier=0d dma_t/rx/err=0/1/0
[x.808870] Bluetooth: hci0: Frame reassembly failed (-84)
In the debug snippet, received field indicates 1 byte was transferred
over DMA and 12 bytes after that with the non-DMA Rx. The sole byte DMA
handled was corrupted (gets zeroed) which leads to the HCI failure.
This problem became apparent after commit
e8ffbb71f783 ("serial: 8250:
use THRE & __stop_tx also with DMA") changed Tx stop behavior. Tx stop
is now triggered from a THRI interrupt.
Despite that this problem looks like a HW bug, this fix is not adding
UART_BUG_xx flag to the driver beucase it seems useful in general to
avoid starting DMA when there are only a few bytes to transfer.
Skipping DMA for small transfers avoids the extra overhead DMA incurs.
Thus, don't setup DMA Rx on UART_IIR_THRI but leave it to a subsequent
interrupt which has Rx a related IIR value.
By returning false from handle_rx_dma(), the DMA vs non-DMA decision is
postponed until either UART_IIR_RDI (FIFO threshold worth of bytes
awaiting) or UART_IIR_TIMEOUT (inter-character timeout) triggers at a
later time which allows better to discern whether the number of bytes
warrants starting DMA or not.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Fixes:
e8ffbb71f783 ("serial: 8250: use THRE & __stop_tx also with DMA")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230317103034.12881-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Fri, 17 Mar 2023 09:46:57 +0000 (10:46 +0100)]
dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
commit
7b21f329ae0ab6361c0aebfc094db95821490cd1 upstream.
The fourth interrupt on SCIF variants with four interrupts (RZ/A1) is
the Break interrupt, not the Transmit End interrupt (like on SCI(g)).
Update the description and interrupt name to fix this.
Fixes:
384d00fae8e51f8f ("dt-bindings: serial: sh-sci: Convert to json-schema")
Cc: stable <stable@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/719d1582e0ebbe3d674e3a48fc26295e1475a4c3.1679046394.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ryusuke Konishi [Thu, 30 Mar 2023 20:55:15 +0000 (05:55 +0900)]
nilfs2: fix sysfs interface lifetime
commit
42560f9c92cc43dce75dbf06cc0d840dced39b12 upstream.
The current nilfs2 sysfs support has issues with the timing of creation
and deletion of sysfs entries, potentially leading to null pointer
dereferences, use-after-free, and lockdep warnings.
Some of the sysfs attributes for nilfs2 per-filesystem instance refer to
metadata file "cpfile", "sufile", or "dat", but
nilfs_sysfs_create_device_group that creates those attributes is executed
before the inodes for these metadata files are loaded, and
nilfs_sysfs_delete_device_group which deletes these sysfs entries is
called after releasing their metadata file inodes.
Therefore, access to some of these sysfs attributes may occur outside of
the lifetime of these metadata files, resulting in inode NULL pointer
dereferences or use-after-free.
In addition, the call to nilfs_sysfs_create_device_group() is made during
the locking period of the semaphore "ns_sem" of nilfs object, so the
shrinker call caused by the memory allocation for the sysfs entries, may
derive lock dependencies "ns_sem" -> (shrinker) -> "locks acquired in
nilfs_evict_inode()".
Since nilfs2 may acquire "ns_sem" deep in the call stack holding other
locks via its error handler __nilfs_error(), this causes lockdep to report
circular locking. This is a false positive and no circular locking
actually occurs as no inodes exist yet when
nilfs_sysfs_create_device_group() is called. Fortunately, the lockdep
warnings can be resolved by simply moving the call to
nilfs_sysfs_create_device_group() out of "ns_sem".
This fixes these sysfs issues by revising where the device's sysfs
interface is created/deleted and keeping its lifetime within the lifetime
of the metadata files above.
Link: https://lkml.kernel.org/r/20230330205515.6167-1-konishi.ryusuke@gmail.com
Fixes:
dd70edbde262 ("nilfs2: integrate sysfs support into driver")
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Reported-by: syzbot+979fa7f9c0d086fdc282@syzkaller.appspotmail.com
Link: https://lkml.kernel.org/r/0000000000003414b505f7885f7e@google.com
Reported-by: syzbot+5b7d542076d9bddc3c6a@syzkaller.appspotmail.com
Link: https://lkml.kernel.org/r/0000000000006ac86605f5f44eb9@google.com
Cc: Viacheslav Dubeyko <slava@dubeyko.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ryusuke Konishi [Mon, 27 Mar 2023 17:53:18 +0000 (02:53 +0900)]
nilfs2: fix potential UAF of struct nilfs_sc_info in nilfs_segctor_thread()
commit
6be49d100c22ffea3287a4b19d7639d259888e33 upstream.
The finalization of nilfs_segctor_thread() can race with
nilfs_segctor_kill_thread() which terminates that thread, potentially
causing a use-after-free BUG as KASAN detected.
At the end of nilfs_segctor_thread(), it assigns NULL to "sc_task" member
of "struct nilfs_sc_info" to indicate the thread has finished, and then
notifies nilfs_segctor_kill_thread() of this using waitqueue
"sc_wait_task" on the struct nilfs_sc_info.
However, here, immediately after the NULL assignment to "sc_task", it is
possible that nilfs_segctor_kill_thread() will detect it and return to
continue the deallocation, freeing the nilfs_sc_info structure before the
thread does the notification.
This fixes the issue by protecting the NULL assignment to "sc_task" and
its notification, with spinlock "sc_state_lock" of the struct
nilfs_sc_info. Since nilfs_segctor_kill_thread() does a final check to
see if "sc_task" is NULL with "sc_state_lock" locked, this can eliminate
the race.
Link: https://lkml.kernel.org/r/20230327175318.8060-1-konishi.ryusuke@gmail.com
Reported-by: syzbot+b08ebcc22f8f3e6be43a@syzkaller.appspotmail.com
Link: https://lkml.kernel.org/r/00000000000000660d05f7dfa877@google.com
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sherry Sun [Thu, 23 Mar 2023 05:44:15 +0000 (13:44 +0800)]
tty: serial: fsl_lpuart: avoid checking for transfer complete when UARTCTRL_SBK is asserted in lpuart32_tx_empty
commit
9425914f3de6febbd6250395f56c8279676d9c3c upstream.
According to LPUART RM, Transmission Complete Flag becomes 0 if queuing
a break character by writing 1 to CTRL[SBK], so here need to avoid
checking for transmission complete when UARTCTRL_SBK is asserted,
otherwise the lpuart32_tx_empty may never get TIOCSER_TEMT.
Commit
2411fd94ceaa("tty: serial: fsl_lpuart: skip waiting for
transmission complete when UARTCTRL_SBK is asserted") only fix it in
lpuart32_set_termios(), here also fix it in lpuart32_tx_empty().
Fixes:
380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20230323054415.20363-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Biju Das [Tue, 21 Mar 2023 11:47:50 +0000 (11:47 +0000)]
tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
commit
f92ed0cd9328aed918ebb0ebb64d259eccbcc6e7 upstream.
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes:
dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Biju Das [Fri, 17 Mar 2023 15:04:03 +0000 (15:04 +0000)]
tty: serial: sh-sci: Fix transmit end interrupt handler
commit
b43a18647f03c87e77d50d6fe74904b61b96323e upstream.
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes:
e1d0be616186 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Thu, 23 Feb 2023 02:00:59 +0000 (10:00 +0800)]
iio: light: cm32181: Unregister second I2C client if present
commit
099cc90a5a62e68b2fe3a42da011ab929b98bf73 upstream.
If a second dummy client that talks to the actual I2C address was
created in probe(), there should be a proper cleanup on driver and
device removal to avoid leakage.
So unregister the dummy client via another callback.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Fixes:
c1e62062ff54 ("iio: light: cm32181: Handle CM3218 ACPI devices with 2 I2C resources")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2152281
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20230223020059.2013993-1-kai.heng.feng@canonical.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nuno Sá [Thu, 16 Feb 2023 10:14:51 +0000 (11:14 +0100)]
iio: buffer: make sure O_NONBLOCK is respected
commit
3da1814184582ed0faf039275a3f02e6f69944ee upstream.
For output buffers, there's no guarantee that the buffer won't be full
in the first iteration of the loop in which case we would block
independently of userspace passing O_NONBLOCK or not. Fix it by always
checking the flag before going to sleep.
While at it (and as it's a bit related), refactored the loop so that the
stop condition is 'written != n', i.e, run the loop until all data has
been copied into the IIO buffers. This makes the code a bit simpler.
Fixes:
9eeee3b0bf190 ("iio: Add output buffer support")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230216101452.591805-3-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nuno Sá [Thu, 16 Feb 2023 10:14:50 +0000 (11:14 +0100)]
iio: buffer: correctly return bytes written in output buffers
commit
b5184a26a28fac1d708b0bfeeb958a9260c2924c upstream.
If for some reason 'rb->access->write()' does not write the full
requested data and the O_NONBLOCK is set, we would return 'n' to
userspace which is not really truth. Hence, let's return the number of
bytes we effectively wrote.
Fixes:
9eeee3b0bf190 ("iio: Add output buffer support")
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20230216101452.591805-2-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
William Breathitt Gray [Sat, 11 Mar 2023 00:22:48 +0000 (19:22 -0500)]
iio: dac: cio-dac: Fix max DAC write value check for 12-bit
commit
c3701185ee1973845db088d8b0fc443397ab0eb2 upstream.
The CIO-DAC series of devices only supports DAC values up to 12-bit
rather than 16-bit. Trying to write a 16-bit value results in only the
lower 12 bits affecting the DAC output which is not what the user
expects. Instead, adjust the DAC write value check to reject values
larger than 12-bit so that they fail explicitly as invalid for the user.
Fixes:
3b8df5fd526e ("iio: Add IIO support for the Measurement Computing CIO-DAC family")
Cc: stable@vger.kernel.org
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20230311002248.8548-1-william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars-Peter Clausen [Sun, 12 Mar 2023 21:09:33 +0000 (14:09 -0700)]
iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
commit
363c7dc72f79edd55bf1c4380e0fbf7f1bbc2c86 upstream.
The ads7950 uses a mutex as well as SPI transfers in its GPIO callbacks.
This means these callbacks can sleep and the `can_sleep` flag should be
set.
Having the flag set will make sure that warnings are generated when calling
any of the callbacks from a potentially non-sleeping context.
Fixes:
c97dce792dc8 ("iio: adc: ti-ads7950: add GPIO support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: David Lechner <david@lechnology.com>
Link: https://lore.kernel.org/r/20230312210933.2275376-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Shevchenko [Wed, 18 Jan 2023 10:06:23 +0000 (12:06 +0200)]
iio: adc: qcom-spmi-adc5: Fix the channel name
commit
701c875aded880013aacac608832995c4b052257 upstream.
The node name can contain an address part which is unused
by the driver. Moreover, this string is propagated into
the userspace label, sysfs filenames *and breaking ABI*.
Cut the address part out before assigning the channel name.
Fixes:
4f47a236a23d ("iio: adc: qcom-spmi-adc5: convert to device properties")
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20230118100623.42255-1-andriy.shevchenko@linux.intel.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Tue, 31 Jan 2023 09:46:11 +0000 (10:46 +0100)]
iio: adis16480: select CONFIG_CRC32
commit
d9b540ee461cca7edca0dd2c2a42625c6b9ffb8f upstream.
In rare randconfig builds, the missing CRC32 helper causes
a link error:
ld.lld: error: undefined symbol: crc32_le
>>> referenced by usercopy_64.c
>>> vmlinux.o:(adis16480_trigger_handler)
Fixes:
941f130881fa ("iio: adis16480: support burst read function")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230131094616.130238-1-arnd@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Ray [Fri, 27 Jan 2023 12:57:14 +0000 (14:57 +0200)]
drivers: iio: adc: ltc2497: fix LSB shift
commit
6327a930ab7bfa1ab33bcdffd5f5f4b1e7131504 upstream.
Correct the "sub_lsb" shift for the ltc2497 and drop the sub_lsb element
which is now constant.
An earlier version of the code shifted by 14 but this was a consequence
of reading three bytes into a __be32 buffer and using be32_to_cpu(), so
eight extra bits needed to be skipped. Now we use get_unaligned_be24()
and thus the additional skip is wrong.
Fixes:
2187cfeb3626 ("drivers: iio: adc: ltc2497: LTC2499 support")
Signed-off-by: Ian Ray <ian.ray@ge.com>
Link: https://lore.kernel.org/r/20230127125714.44608-1-ian.ray@ge.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Tue, 28 Mar 2023 18:41:31 +0000 (20:41 +0200)]
USB: serial: option: add Quectel RM500U-CN modem
commit
7708a3858e69db91a8b69487994f33b96d20192a upstream.
This modem supports several modes with a class network function
and a number of serial functions, all using ff/00/00
The device ID is the same in all modes.
RNDIS mode
----------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0900 Rev= 4.04
S: Manufacturer=Quectel
S: Product=RM500U-CN
S: SerialNumber=
0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=c0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=03
I:* If#= 0 Alt= 0 #EPs= 1 Cls=e0(wlcon) Sub=01 Prot=03 Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
ECM mode
--------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0900 Rev= 4.04
S: Manufacturer=Quectel
S: Product=RM500U-CN
S: SerialNumber=
0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=c0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
NCM mode
--------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0900 Rev= 4.04
S: Manufacturer=Quectel
S: Product=RM500U-CN
S: SerialNumber=
0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=c0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0d Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0d Prot=00 Driver=cdc_ncm
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Reported-by: Andrew Green <askgreen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enrico Sau [Tue, 14 Mar 2023 09:00:59 +0000 (10:00 +0100)]
USB: serial: option: add Telit FE990 compositions
commit
773e8e7d07b753474b2ccd605ff092faaa9e65b9 upstream.
Add the following Telit FE990 compositions:
0x1080: tty, adb, rmnet, tty, tty, tty, tty
0x1081: tty, adb, mbim, tty, tty, tty, tty
0x1082: rndis, tty, adb, tty, tty, tty, tty
0x1083: tty, adb, ecm, tty, tty, tty, tty
Signed-off-by: Enrico Sau <enrico.sau@gmail.com>
Link: https://lore.kernel.org/r/20230314090059.77876-1-enrico.sau@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RD Babiera [Wed, 29 Mar 2023 21:51:59 +0000 (21:51 +0000)]
usb: typec: altmodes/displayport: Fix configure initial pin assignment
commit
eddebe39602efe631b83ff8d03f26eba12cfd760 upstream.
While determining the initial pin assignment to be sent in the configure
message, using the DP_PIN_ASSIGN_DP_ONLY_MASK mask causes the DFP_U to
send both Pin Assignment C and E when both are supported by the DFP_U and
UFP_U. The spec (Table 5-7 DFP_U Pin Assignment Selection Mandates,
VESA DisplayPort Alt Mode Standard v2.0) indicates that the DFP_U never
selects Pin Assignment E when Pin Assignment C is offered.
Update the DP_PIN_ASSIGN_DP_ONLY_MASK conditional to intially select only
Pin Assignment C if it is available.
Fixes:
0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230329215159.2046932-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Jan Koster [Sat, 18 Feb 2023 14:18:30 +0000 (15:18 +0100)]
USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs
commit
71f8afa2b66e356f435b6141b4a9ccf953e18356 upstream.
The Silicon Labs IFS-USB-DATACABLE is used in conjunction with for example
the Quint UPSes. It is used to enable Modbus communication with the UPS to
query configuration, power and battery status.
Signed-off-by: Kees Jan Koster <kjkoster@kjkoster.org>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Thu, 30 Mar 2023 15:02:24 +0000 (18:02 +0300)]
usb: dwc3: pci: add support for the Intel Meteor Lake-S
commit
ec799c8a92e0be91e0940cc739a27f483242df65 upstream.
This patch adds the necessary PCI ID for Intel Meteor Lake-S
devices.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230330150224.89316-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pawel Laszczak [Fri, 31 Mar 2023 09:06:00 +0000 (05:06 -0400)]
usb: cdnsp: Fixes error: uninitialized symbol 'len'
commit
1edf48991a783d00a3a18dc0d27c88139e4030a2 upstream.
The patch
5bc38d33a5a1: "usb: cdnsp: Fixes issue with redundant
Status Stage" leads to the following Smatch static checker warning:
drivers/usb/cdns3/cdnsp-ep0.c:470 cdnsp_setup_analyze()
error: uninitialized symbol 'len'.
cc: <stable@vger.kernel.org>
Fixes:
5bc38d33a5a1 ("usb: cdnsp: Fixes issue with redundant Status Stage")
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20230331090600.454674-1-pawell@cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
D Scott Phillips [Thu, 30 Mar 2023 14:30:54 +0000 (17:30 +0300)]
xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
commit
ecaa4902439298f6b0e29f47424a86b310a9ff4f upstream.
Previously the quirk was skipped when no iommu was present. The same
rationale for skipping the quirk also applies in the iommu.passthrough=1
case.
Skip applying the XHCI_ZERO_64B_REGS quirk if the device's iommu domain is
passthrough.
Fixes:
12de0a35c996 ("xhci: Add quirk to zero 64bit registers on Renesas PCIe controllers")
Cc: stable <stable@kernel.org>
Signed-off-by: D Scott Phillips <scott@os.amperecomputing.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Thu, 30 Mar 2023 14:30:56 +0000 (17:30 +0300)]
xhci: Free the command allocated for setting LPM if we return early
commit
f6caea4855553a8b99ba3ec23ecdb5ed8262f26c upstream.
The command allocated to set exit latency LPM values need to be freed in
case the command is never queued. This would be the case if there is no
change in exit latency values, or device is missing.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/linux-usb/24263902-c9b3-ce29-237b-1c3d6918f4fe@alu.unizg.hr
Tested-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Fixes:
5c2a380a5aa8 ("xhci: Allocate separate command structures for each LPM command")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20230330143056.1390020-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wayne Chang [Mon, 27 Mar 2023 09:55:48 +0000 (17:55 +0800)]
usb: xhci: tegra: fix sleep in atomic call
commit
4c7f9d2e413dc06a157c4e5dccde84aaf4655eb3 upstream.
When we set the dual-role port to Host mode, we observed the following
splat:
[ 167.057718] BUG: sleeping function called from invalid context at
include/linux/sched/mm.h:229
[ 167.057872] Workqueue: events tegra_xusb_usb_phy_work
[ 167.057954] Call trace:
[ 167.057962] dump_backtrace+0x0/0x210
[ 167.057996] show_stack+0x30/0x50
[ 167.058020] dump_stack_lvl+0x64/0x84
[ 167.058065] dump_stack+0x14/0x34
[ 167.058100] __might_resched+0x144/0x180
[ 167.058140] __might_sleep+0x64/0xd0
[ 167.058171] slab_pre_alloc_hook.constprop.0+0xa8/0x110
[ 167.058202] __kmalloc_track_caller+0x74/0x2b0
[ 167.058233] kvasprintf+0xa4/0x190
[ 167.058261] kasprintf+0x58/0x90
[ 167.058285] tegra_xusb_find_port_node.isra.0+0x58/0xd0
[ 167.058334] tegra_xusb_find_port+0x38/0xa0
[ 167.058380] tegra_xusb_padctl_get_usb3_companion+0x38/0xd0
[ 167.058430] tegra_xhci_id_notify+0x8c/0x1e0
[ 167.058473] notifier_call_chain+0x88/0x100
[ 167.058506] atomic_notifier_call_chain+0x44/0x70
[ 167.058537] tegra_xusb_usb_phy_work+0x60/0xd0
[ 167.058581] process_one_work+0x1dc/0x4c0
[ 167.058618] worker_thread+0x54/0x410
[ 167.058650] kthread+0x188/0x1b0
[ 167.058672] ret_from_fork+0x10/0x20
The function tegra_xusb_padctl_get_usb3_companion eventually calls
tegra_xusb_find_port and this in turn calls kasprintf which might sleep
and so cannot be called from an atomic context.
Fix this by moving the call to tegra_xusb_padctl_get_usb3_companion to
the tegra_xhci_id_work function where it is really needed.
Fixes:
f836e7843036 ("usb: xhci-tegra: Add OTG support")
Cc: stable@vger.kernel.org
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Link: https://lore.kernel.org/r/20230327095548.1599470-1-haotienh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 11 Mar 2023 14:40:06 +0000 (15:40 +0100)]
PCI/DOE: Fix memory leak with CONFIG_DEBUG_OBJECTS=y
commit
abf04be0e7071f2bcd39bf97ba407e7d4439785e upstream.
After a pci_doe_task completes, its work_struct needs to be destroyed
to avoid a memory leak with CONFIG_DEBUG_OBJECTS=y.
Fixes:
9d24322e887b ("PCI/DOE: Add DOE mailbox support functions")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/775768b4912531c3b887d405fc51a50e465e1bf9.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 11 Mar 2023 14:40:05 +0000 (15:40 +0100)]
PCI/DOE: Silence WARN splat with CONFIG_DEBUG_OBJECTS=y
commit
92dc899c3b4927f3cfa23f55bf759171234b5802 upstream.
Gregory Price reports a WARN splat with CONFIG_DEBUG_OBJECTS=y upon CXL
probing because pci_doe_submit_task() invokes INIT_WORK() instead of
INIT_WORK_ONSTACK() for a work_struct that was allocated on the stack.
All callers of pci_doe_submit_task() allocate the work_struct on the
stack, so replace INIT_WORK() with INIT_WORK_ONSTACK() as a backportable
short-term fix.
The long-term fix implemented by a subsequent commit is to move to a
synchronous API which allocates the work_struct internally in the DOE
library.
Stacktrace for posterity:
WARNING: CPU: 0 PID: 23 at lib/debugobjects.c:545 __debug_object_init.cold+0x18/0x183
CPU: 0 PID: 23 Comm: kworker/u2:1 Not tainted 6.1.0-0.rc1.20221019gitaae703b02f92.17.fc38.x86_64 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
pci_doe_submit_task+0x5d/0xd0
pci_doe_discovery+0xb4/0x100
pcim_doe_create_mb+0x219/0x290
cxl_pci_probe+0x192/0x430
local_pci_probe+0x41/0x80
pci_device_probe+0xb3/0x220
really_probe+0xde/0x380
__driver_probe_device+0x78/0x170
driver_probe_device+0x1f/0x90
__driver_attach_async_helper+0x5c/0xe0
async_run_entry_fn+0x30/0x130
process_one_work+0x294/0x5b0
Fixes:
9d24322e887b ("PCI/DOE: Add DOE mailbox support functions")
Link: https://lore.kernel.org/linux-cxl/Y1bOniJliOFszvIK@memverge.com/
Reported-by: Gregory Price <gregory.price@memverge.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Cc: stable@vger.kernel.org # v6.0+
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/67a9117f463ecdb38a2dbca6a20391ce2f1e7a06.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 11 Mar 2023 14:40:04 +0000 (15:40 +0100)]
cxl/pci: Handle excessive CDAT length
commit
4fe2c13d59d849be3b45371e3913ec5dc77fc0fb upstream.
If the length in the CDAT header is larger than the concatenation of the
header and all table entries, then the CDAT exposed to user space
contains trailing null bytes.
Not every consumer may be able to handle that. Per Postel's robustness
principle, "be liberal in what you accept" and silently reduce the
cached length to avoid exposing those null bytes.
Fixes:
c97006046c79 ("cxl/port: Read CDAT table")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Link: https://lore.kernel.org/r/6d98b3c7da5343172bd3ccabfabbc1f31c079d74.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 11 Mar 2023 14:40:03 +0000 (15:40 +0100)]
cxl/pci: Handle truncated CDAT entries
commit
b56faef2312057db20479b240eb71bd2e51fb51c upstream.
If truncated CDAT entries are received from a device, the concatenation
of those entries constitutes a corrupt CDAT, yet is happily exposed to
user space.
Avoid by verifying response lengths and erroring out if truncation is
detected.
The last CDAT entry may still be truncated despite the checks introduced
herein if the length in the CDAT header is too small. However, that is
easily detectable by user space because it reaches EOF prematurely.
A subsequent commit which rightsizes the CDAT response allocation closes
that remaining loophole.
The two lines introduced here which exceed 80 chars are shortened to
less than 80 chars by a subsequent commit which migrates to a
synchronous DOE API and replaces "t.task.rv" by "rc".
The existing acpi_cdat_header and acpi_table_cdat struct definitions
provided by ACPICA cannot be used because they do not employ __le16 or
__le32 types. I believe that cannot be changed because those types are
Linux-specific and ACPI is specified for little endian platforms only,
hence doesn't care about endianness. So duplicate the structs.
Fixes:
c97006046c79 ("cxl/port: Read CDAT table")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Link: https://lore.kernel.org/r/bce3aebc0e8e18a1173425a7a865b232c3912963.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 11 Mar 2023 14:40:02 +0000 (15:40 +0100)]
cxl/pci: Handle truncated CDAT header
commit
34bafc747c54fb58c1908ec3116fa6137393e596 upstream.
cxl_cdat_get_length() only checks whether the DOE response size is
sufficient for the Table Access response header (1 dword), but not the
succeeding CDAT header (1 dword length plus other fields).
It thus returns whatever uninitialized memory happens to be on the stack
if a truncated DOE response with only 1 dword was received. Fix it.
Fixes:
c97006046c79 ("cxl/port: Read CDAT table")
Reported-by: Ming Li <ming4.li@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ming Li <ming4.li@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lore.kernel.org/r/000e69cd163461c8b1bc2cf4155b6e25402c29c7.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Wunner [Sat, 11 Mar 2023 14:40:01 +0000 (15:40 +0100)]
cxl/pci: Fix CDAT retrieval on big endian
commit
fbaa38214cd9e150764ccaa82e04ecf42cc1140c upstream.
The CDAT exposed in sysfs differs between little endian and big endian
arches: On big endian, every 4 bytes are byte-swapped.
PCI Configuration Space is little endian (PCI r3.0 sec 6.1). Accessors
such as pci_read_config_dword() implicitly swap bytes on big endian.
That way, the macros in include/uapi/linux/pci_regs.h work regardless of
the arch's endianness. For an example of implicit byte-swapping, see
ppc4xx_pciex_read_config(), which calls in_le32(), which uses lwbrx
(Load Word Byte-Reverse Indexed).
DOE Read/Write Data Mailbox Registers are unlike other registers in
Configuration Space in that they contain or receive a 4 byte portion of
an opaque byte stream (a "Data Object" per PCIe r6.0 sec 7.9.24.5f).
They need to be copied to or from the request/response buffer verbatim.
So amend pci_doe_send_req() and pci_doe_recv_resp() to undo the implicit
byte-swapping.
The CXL_DOE_TABLE_ACCESS_* and PCI_DOE_DATA_OBJECT_DISC_* macros assume
implicit byte-swapping. Byte-swap requests after constructing them with
those macros and byte-swap responses before parsing them.
Change the request and response type to __le32 to avoid sparse warnings.
Per a request from Jonathan, replace sizeof(u32) with sizeof(__le32) for
consistency.
Fixes:
c97006046c79 ("cxl/port: Read CDAT table")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org # v6.0+
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/3051114102f41d19df3debbee123129118fc5e6d.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Sit Wei Hong [Thu, 6 Apr 2023 02:45:41 +0000 (10:45 +0800)]
net: stmmac: check fwnode for phy device before scanning for phy
[ Upstream commit
8fbc10b995a506e173f1080dfa2764f232a65e02 ]
Some DT devices already have phy device configured in the DT/ACPI.
Current implementation scans for a phy unconditionally even though
there is a phy listed in the DT/ACPI and already attached.
We should check the fwnode if there is any phy device listed in
fwnode and decide whether to scan for a phy to attach to.
Fixes:
fe2cfbc96803 ("net: stmmac: check if MAC needs to attach to a PHY")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/lkml/20230403212434.296975-1-martin.blumenstingl@googlemail.com/
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shahab Vahedi <shahab@synopsys.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Link: https://lore.kernel.org/r/20230406024541.3556305-1-michael.wei.hong.sit@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ard Biesheuvel [Tue, 4 Apr 2023 10:36:25 +0000 (12:36 +0200)]
arm64: compat: Work around uninitialized variable warning
[ Upstream commit
32d85999680601d01b2a36713c9ffd7397c8688b ]
Dan reports that smatch complains about a potential uninitialized
variable being used in the compat alignment fixup code.
The logic is not wrong per se, but we do end up using an uninitialized
variable if reading the instruction that triggered the alignment fault
from user space faults, even if the fault ensures that the uninitialized
value doesn't propagate any further.
Given that we just give up and return 1 if any fault occurs when reading
the instruction, let's get rid of the 'success handling' pattern that
captures the fault in a variable and aborts later, and instead, just
return 1 immediately if any of the get_user() calls result in an
exception.
Fixes:
3fc24ef32d3b ("arm64: compat: Implement misalignment fixups for multiword loads")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202304021214.gekJ8yRc-lkp@intel.com/
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20230404103625.2386382-1-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / platform / kernel / linux-starfive.git / log