ath9k: clean up hardware code for beacon handling

The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.

SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.

Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: update information elements in cached BSS struct

When a cached BSS struct is updated because a new beacon was received,
the code replaces the cached information elements by the IEs from the
new beacon. However it did not update the pub.information_elements
and pub.len_information_elements fields leaving them either pointing
to the old beacon IEs or in an inconsistent state where the data is
replaced by the new beacon IEs but len_information_elements still has
its value from the first beacon.

Fix this by updating the information elements fields if they are
pointing to beacon IEs.

Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Missed to clear key4 of micentry

key4 of micentry is used, if ATH_CRYPT_CAP_MIC_COMBINED is set.
But is not cleared on key cache reset.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add change_interface callback

Add support to change interface type
without bringing down the interface.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add antenna availability information

Add a field to wiphy for the hardware to report the availble antennas for
configuration. Only if this is set to something bigger than zero, will the
anntenna configuration ops be executed.

Allthough this could be a simple number of antennas, I defined it as a bitmap
of antennas which are available for configuration, since it's more consistent
with the rest of the antenna API and there could be cases where the
hardware allows only configuration of certain antennas. As it does not make
much of a difference in size or normal usage, I think it's better to be able to
support this, in case the need arises.

The antenna configuration is now also checked against the availabe antennas and
rejected if it does not match.

Signed-off-by: Bruno Randolf <br1@einfach.org>
--
v3: always apply available antenna mask (for "all" antennas case).

v2: reject antenna configurations which don't match the available antennas
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix assumptions for idle calls on suspend/resume

mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.

This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.

What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix power save count imbalance on ath_radio_enable()

Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:

ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000

This would make the chip useless upon resume.

I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: fix build break with ATH_DBG_WARN_ON_ONCE

Description by Hauke:

"If CONFIG_ATH_DEBUG=y is set ATH_DBG_WARN_ON_ONCE uses WARN_ON_ONCE and
returns something, but if CONFIG_ATH_DEBUG is not set it does not return
anything. Now ATH_DBG_WARN_ON_ONCE is used in the boolean expression in
an if case and is not returning anything and causes a compile error.

  CC [M]  /drivers/net/wireless/ath/ath9k/main.o
/drivers/net/wireless/ath/ath9k/main.c: In function ‘ath_isr’:
/drivers/net/wireless/ath/ath9k/main.c:769: error: expected expression
before ‘do’
make[5]: *** [/drivers/net/wireless/ath/ath9k/main.o] Error 1
make[4]: *** [/drivers/net/wireless/ath/ath9k] Error 2"

Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix modinfo does not list alias -> pci-id lines

The AHB bus support patchset moved the table "Known PCI ids" from base.c
to pci.c - unfortunately, MODULE_DEVICE_TABLE() was not transferred.
With this fix 'modinfo ath5k' lists the alias -> pci-id lines, again.

The issue was introduced by:
   commit e5b046d86fac609f636d127a38de94a175c7e83b
   "ath5k: Move PCI bus functions to separate file."

Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

Conflicts:
drivers/net/wireless/ath/ath9k/ath9k.h
drivers/net/wireless/ath/ath9k/main.c
drivers/net/wireless/ath/ath9k/xmit.c

ath9k_hw: warn if we cannot change the power to the chip

Suspend requires the device to be in fullsleep otherwise upon
resume the device becomes unresponsive. We need to ensure
that when we want the device to go to sleep it yields to
the request, otherwise we'll have a useless devices upon
resume. Warn when changing the power fails as we need
to look into these issues.

Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: skip ATH9K_INT_TIM_TIMER when we are idle

We should not be idle when we get the ATH9K_INT_TIM_TIMER,
otherwise its a sign of something broken in our design with
our idle state machine and mac80211. Skip these and WARN once
just in case this is triggerable.

Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add some element IDs in enum ieee80211_eid

1)WLAN_EID_BSS_COEX_2040
2)WLAN_EID_OVERLAP_BSS_SCAN_PARAM
3)WLAN_EID_EXT_CAPABILITY

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: rename config option for N-PHY, drop BROKEN

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: fix split of N-PHY devices into supported and not (based on PHY rev)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: set TMS to work with current band width for N-PHY

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: silence warnings

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Show max number of probe tries in debug message.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: flush PHY writes when needed

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: implement own maskset

This let us avoid double addressing while still having reg check.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: reorder and optimize tables initialization

Order was changed in specs. For writing arrays we have designed bulk function
which makes use of auto increment and do not write table address over and over.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: N-PHY: update init tables

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Check for NULL sta in ath_tx_start

It can be NULL according to docs, and logging showed it
to be NULL in practice.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Apply ht_opmode changes in ieee80211_change_bss

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: Add new BSS attribute ht_opmode

Add a new BSS attribute to allow hostapd to set the current HT opmode.
Otherwise drivers won't be able to set up protection for HT rates in
AP mode.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: fix TKIP countermeasure behaviour

Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.

This bug causes the response of the system to certain attacks to be
ineffective.

It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.

wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.

The log tends to look like:

State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.

Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: clear countermeasure setting on commit

... and interface up.

In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.

Clear the setting so that the reporting matches what the driver has
done..

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs

mac80211 doesn't handle shared skbs correctly at the moment. As a result
a possible resize can trigger a BUG in pskb_expand_head.

[  676.030000] Kernel bug detected[#1]:
[  676.030000] Cpu 0
[  676.030000] $ 0   : 00000000 00000000 819662ff 00000002
[  676.030000] $ 4   : 81966200 00000020 00000000 00000020
[  676.030000] $ 8   : 819662e0 800043c0 00000002 00020000
[  676.030000] $12   : 3b9aca00 00000000 00000000 00470000
[  676.030000] $16   : 80ea2000 00000000 00000000 00000000
[  676.030000] $20   : 818aa200 80ea2018 80ea2000 00000008
[  676.030000] $24   : 00000002 800ace5c
[  676.030000] $28   : 8199a000 8199bd20 81938f88 80f180d4
[  676.030000] Hi    : 0000026e
[  676.030000] Lo    : 0000757e
[  676.030000] epc   : 801245e4 pskb_expand_head+0x44/0x1d8
[  676.030000]     Not tainted
[  676.030000] ra    : 80f180d4 ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] Status: 1000a403    KERNEL EXL IE
[  676.030000] Cause : 10800024
[  676.030000] PrId  : 0001964c (MIPS 24Kc)
[  676.030000] Modules linked in: mac80211_hwsim rt2800lib rt2x00soc rt2x00pci rt2x00lib mac80211 crc_itu_t crc_ccitt cfg80211 compat arc4 aes_generic deflate ecb cbc [last unloaded: rt2800pci]
[  676.030000] Process kpktgend_0 (pid: 97, threadinfo=8199a000, task=81879f48, tls=00000000)
[  676.030000] Stack : ffffffff 00000000 00000000 00000014 00000004 80ea2000 00000000 00000000
[  676.030000]         818aa200 80f180d4 ffffffff 0000000a 81879f78 81879f48 81879f48 00000018
[  676.030000]         81966246 80ea2000 818432e0 80f1a420 80203050 81814d98 00000001 81879f48
[  676.030000]         81879f48 00000018 81966246 818432e0 0000001a 8199bdd4 0000001c 80f1b72c
[  676.030000]         80203020 8001292c 80ef4aa2 7f10b55d 801ab5b8 81879f48 00000188 80005c90
[  676.030000]         ...
[  676.030000] Call Trace:
[  676.030000] [<801245e4>] pskb_expand_head+0x44/0x1d8
[  676.030000] [<80f180d4>] ieee80211_skb_resize+0xb0/0x114 [mac80211]
[  676.030000] [<80f1a420>] ieee80211_xmit+0x150/0x22c [mac80211]
[  676.030000] [<80f1b72c>] ieee80211_subif_start_xmit+0x6f4/0x73c [mac80211]
[  676.030000] [<8014361c>] pktgen_thread_worker+0xfac/0x16f8
[  676.030000] [<8002ebe8>] kthread+0x7c/0x88
[  676.030000] [<80008e0c>] kernel_thread_helper+0x10/0x18
[  676.030000]
[  676.030000]
[  676.030000] Code: 24020001  10620005  2502001f <0200000d> 0804917a  00000000  2502001f  00441023  00531021

Fix this by making a local copy of shared skbs prior to mangeling them.
To avoid copying the skb unnecessarily move the skb_copy call below the
checks that don't need write access to the skb.

Also, move the assignment of nh_pos and h_pos below the skb_copy to point
to the correct skb.

It would be possible to avoid another resize of the copied skb by using
skb_copy_expand instead of skb_copy but that would make the patch more
complex. Also, shared skbs are a corner case right now, so the resize
shouldn't matter much.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix suspend/resume

The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Put the right tsf value in mesh beacons

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Prevent mesh interfaces from being counted as ad-hoc

This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix beaconing in mesh mode

This patch fixes the oops below when attempting to bring up a mesh
interface on ath5k hardware.

[  128.933099] kernel BUG at drivers/net/wireless/ath/ath5k/base.c:197!
[  128.933099] invalid opcode: 0000 [#1]
(...)
[  128.933099] Call Trace:
[  128.933099]  [<c83b77fa>] ? ath5k_beacon_update+0x57/0x1f8 [ath5k]
[  128.933099]  [<c02d9a40>] ? __sysfs_add_one+0x28/0x76
[  128.933099]  [<c83b830e>] ? ath5k_bss_info_changed+0x13f/0x173
[ath5k]
[  128.933099]  [<c82ff629>] ? ieee80211_config_beacon+0xc0/0x17e
[mac80211]
[  128.933099]  [<c82f073e>] ?
ieee80211_bss_info_change_notify+0x182/0x18b [mac80211]
[  128.933099]  [<c83b81cf>] ? ath5k_bss_info_changed+0x0/0x173 [ath5k]
[  128.933099]  [<c82ff6d6>] ? ieee80211_config_beacon+0x16d/0x17e
[mac80211]
[  128.933099]  [<c82ff753>] ? ieee80211_add_beacon+0x34/0x39 [mac80211]
[  128.933099]  [<c830a4ed>] ? ieee80211s_init+0xf8/0x10f [mac80211]
[  128.933099]  [<c830a5df>] ? ieee80211_mesh_init_sdata+0xdb/0x154 [mac80211]

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: initialise priv->hw before assigning the interrupt

The interrupt handler takes a lock - but since commit bcad6e80f3f this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.

Fix orinoco_cs and spectrum_cs

<https://bugzilla.kernel.org/show_bug.cgi?id=23932>

Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Fix compilation error when mesh is disabled

Wrap mesh sections inside CONFIG_MAC80211_MESH to fix compilation
problems reported by Stephen Rothwell, Larry Finger and Bruno Randolf.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Remove dead code in recv.c

The structure struct ieee80211_rx_status *rxs is no longer needed to be
passed to ath_rx_send_to_mac80211 function

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Parse DTIM period from mac80211

With the current save power save implementation we assume a dtim period
of 1.This value is assigned based on a sanity check in the driver
eventhough we had not parsed it from mac80211.This patch obtains the actual
DTIM period from AP by parsing it from mac80211.Yet for handling
multicast traffic we may still have it as fixed rather than parsing it
from mac80211 .This does not breaks power save or anything as the sleep
duration is currently fixed in the driver.This patch may serve to improve
power save in the future by using dtim period for sleep duration and using
correct dtim period adhoc mode.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Properly use unlikely check macro

AUTOSLEEP feature is enabled only for AR9271 and AR9003 version
chipsets.So unlikely macro should be used only to check whether
auto-sleep feature is enabled

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix panic on FW download failure

Use the correct error condition exit in case firmware download
fails for some reason. Not doing so results in a panic:

usb 1-3: ath9k_htc: Transferred FW: ar9271.fw, size: 51280
usb 1-3: ath9k_htc: Firmware - ar9271.fw download failed
usb 1-3: ath9k_htc: Target is unresponsive
Failed to initialize the device
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
Pid: 2823, comm: insmod Tainted: G        W   2.6.37-rc4-wl #11
Call Trace:
[<ffffffff81090d7e>] __lock_acquire+0xe3e/0x1d00
[<ffffffff813a9f14>] ? restore_args+0x0/0x30
[<ffffffff81058af1>] ? vprintk+0x321/0x500
[<ffffffff81092290>] lock_acquire+0xa0/0x190
[<ffffffffa02a0eac>] ? usb_kill_anchored_urbs+0x1c/0x80 [usbcore]
[<ffffffff813a8ea8>] _raw_spin_lock_irq+0x48/0x60
[<ffffffffa02a0eac>] ? usb_kill_anchored_urbs+0x1c/0x80 [usbcore]
[<ffffffff813a53fd>] ? printk+0x3c/0x3f
[<ffffffffa02a0eac>] usb_kill_anchored_urbs+0x1c/0x80 [usbcore]
[<ffffffffa0055388>] ath9k_hif_usb_dealloc_urbs+0x18/0x40 [ath9k_htc]
[<ffffffffa00557d7>] ath9k_hif_usb_probe+0x227/0x3d0 [ath9k_htc]
[<ffffffffa02a56ac>] usb_probe_interface+0x10c/0x210 [usbcore]
[<ffffffff812ae826>] driver_probe_device+0x96/0x1c0
[<ffffffff812ae9f3>] __driver_attach+0xa3/0xb0
[<ffffffff812ae950>] ? __driver_attach+0x0/0xb0
[<ffffffff812ad6ae>] bus_for_each_dev+0x5e/0x90
[<ffffffff812ae4c9>] driver_attach+0x19/0x20
[<ffffffff812ae038>] bus_add_driver+0x168/0x320
[<ffffffff812aec71>] driver_register+0x71/0x140
[<ffffffff811fc338>] ? __raw_spin_lock_init+0x38/0x70
[<ffffffffa02a438c>] usb_register_driver+0xdc/0x190 [usbcore]
[<ffffffffa0063000>] ? ath9k_htc_init+0x0/0x4f [ath9k_htc]
[<ffffffffa005599e>] ath9k_hif_usb_init+0x1e/0x20 [ath9k_htc]
[<ffffffffa006302b>] ath9k_htc_init+0x2b/0x4f [ath9k_htc]
[<ffffffff8100212f>] do_one_initcall+0x3f/0x180
[<ffffffff8109ef9b>] sys_init_module+0xbb/0x200
[<ffffffff8100bf52>] system_call_fastpath+0x16/0x1b

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Add support for handling TX power configuration

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Cleanup device identification

ath.ko is a common module shared between ath5k, ar9170usb, ath9k and ath9k_htc.
Adding driver specific data to the shared structure would impact all the
drivers. Handling USB device recognition for devices specific to ath9k_htc
can be handled within the driver itself.

Also, AR7010 refers to the processor used in both AR9280/AR9287 based
devices. Rename the device enumerations accordingly.

While at it, check properly for the bus type when choosing the EEPROM
base address for UB95.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix a compiler warning

net/mac80211/mlme.c: In function 'ieee80211_sta_work':
net/mac80211/mlme.c:1981: warning: too many arguments for format

Introduced by commit 04ac3c0ee2c773c321ec472d892635a20556f34d
("mac80211: speed up AP probing using nullfunc frames").

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use capabilities information for the number of TX queues

One thing I missed in my WME series: Older hardware does not have enough
hardware queues to support WME. In this case we just set up one data queue. Use
the capability information to decide how many queues to set up.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Make DMA warning in ath_stoprecv WARN_ON_ONCE.

This decreases spammage in the log.  A single line message
will still be printed, so users can be aware that problem
exists.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Add device id of AR9485 to pci table

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Disable MRC CCK for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Setup paprd only for supported chains

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Program appropriate register for temperature compensation cal for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add IQ cal changes for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Define IQcal correction coefficient registers using index

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Program appropriate chianmask for AR9485 before starting AGC/IQ cal

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure power control only for the supported chains

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Read and configure turnning caps to regulate freq accuracy

Right now it is done for only AR9485, will be done for ar9003 also
after proper testing.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure internal regulator for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Read and configure antenna diversity control for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Configure xpa bias level for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Read spur channel information from eeprom for AR9485

Also spur channel count and range is different for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add a helper function to get spur channel pointer from cal data for AR9003 family

This helper function would be used for AR9485.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Find chansel of AR_PHY_65NM_CH0_SYNTH7 for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Configure pll control for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Find the maximum number of chains that hw supports

Have it in ah->caps. This will be used during various
calibrations.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Enable extended synch for AR9485 to fix L0s recovery issue

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Disable TX STBC for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Disable LDPC for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Eeeprom changes for AR9485

Calibration data are stored at 4k address (0xfff). The cal data
for AR9485 is not compressed so its lengh can exceed 1024 limit,
take care of that.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Initialize tx/rx gain table from initvals.h for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Initialize mode registers for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Enable hw initialization for AR9485

Also make it a supported mac

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Add initvals.h for AR9485

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Define hw version macros for AR9485

AR9485 is a single chain and single band (2.4 Ghz) chip.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: remove MODULE_VERSION

Since this is updated manually and sporadically, it is fairly useless
anyway.

Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Fix ath_dbg access beyond array bound

ar9300RateSize is not necessarily a power of 4.

Change ar9003_hw_set_target_power_eeprom
to print the targetPowerValT2 array one per line.

ath9k_hw_ar9300_set_txpower repeated the output 4 times per line,
change it to print the targetPowerValT2 value one per line.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Convert ath_print to ath_dbg

Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Convert ath_print(.., ATH_DBG_FATAL to ath_err

So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath: Add and use ath_printk and ath_<level>

Add ath_printk and ath_<level> similar to
dev_printk and dev_<level> from device.h

This allows a more gradual rename of ath_print
to to ath_dbg or perhaps ath_debug.

This basically removes debug.h leaving
only an #define ath_printk ath_dbg
there and moving all the ATH_DBG_<foo>
enums to ath.h

I do not think there's much purpose for struct
ath_common * being passed to the ath_printk
functions, but perhaps there might be.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix dynamic-ps/pm_qos magic numbers

mac80211 uses pm_qos (/dev/network_latency) in order to determine the
dynamic ps timeout (or disable the dynamic-ps at all in some cases).

commit ff616381 added a comparison for the current network_latency
against one high value (1900ms), and against the default value
(2000sec, rather than the commented 2sec).

however, the representation of 1900ms was incorrect:
1900ms = 1900000us ( != 1900000000 )

fix it by using USEC_TO_MSEC/SEC consts.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco: allow IW_AUTH_MFP to pass through

The card doesn't support MFP, so silently accept DISABLED and OPTIONAL
settings.

This avoids the following failure in wpa_supplicant logs:

State: SCANNING -> ASSOCIATING
wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
netlink: Operstate: linkmode=-1, operstate=5
wpa_driver_wext_associate
wpa_driver_wext_set_drop_unencrypted
wpa_driver_wext_set_psk
wpa_driver_wext_associate: assoc failed because set_auth_param(IW_AUTH_MFP) failed
Association request to the driver failed

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Reported by: Giacomo Comes <comes@naic.edu>

Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/mac80211: Report signal average

Extend nl80211 to report an exponential weighted moving average (EWMA) of the
signal value. Since the signal value usually fluctuates between different
packets, an average can be more useful than the value of the last packet.

This uses the recently added generic EWMA library function.

--
v2: fix ABI breakage and change factor to be a power of 2.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix beacon resource related race condition

The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.

This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix STA disconnect issue due to received MIC failed bcast frames

AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.

Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.

Able to pass Wifi Test case 5.2.18 with this fix.

Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix a DMA related race condition on reset

When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix bug in tx power

The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.

Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: jiffies based tx queues watchdog

This patch replace monitor/recover timer by watchdog based on time
stamp. New code allow to discover hangs more precisely.

Timeout values are currently doubled monitoring period values of
previous timer. This have to be tuned based of firmware timing
capabilities.

Tested on 3945, 4965, 5300, 6300.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: prevent too frequent firmware resets

Similarly like on iwlagn, initialize reset duration on iwl3945 to prevent
too frequent firmware resets.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211/mac80211: add mesh join/leave commands

Instead of tying mesh activity to interface up,
add join and leave commands for mesh. Since we
must be backward compatible, let cfg80211 handle
joining a mesh if a mesh ID was pre-configured
when the device goes up.

Note that this therefore must modify mac80211 as
well since mac80211 needs to lose the logic to
start the mesh on interface up.

We now allow querying mesh parameters before the
mesh is connected, which simply returns defaults.
Setting them (internally renamed to "update") is
only allowed while connected. Specify them with
the new mesh join command instead where needed.

In mac80211, beaconing must now also follow the
mesh enabled/not enabled state, which is done
by testing the mesh ID.

Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: refactor mesh parameter parsing

I'm going to need this in a new place later.

Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: require add_virtual_intf to return new dev

cfg80211 used to do all its bookkeeping in
the notifier, but some new stuff will have
to use local variables so make the callback
return the netdev pointer.

Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: move mesh filter adjusting

Logically, the filter adjusting belongs with
starting/stopping mesh, not interface up/down,
so move it there.

Tested-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211/mac80211: define and allow configuring mesh element TTL

The TTL in path selection information elements is different from
the mesh ttl used in mesh data frames.  Version 7.03 of the 11s
draft calls this ttl 'Element TTL'.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Include tx ack reporting on hw flags

 * Since we report tx acks to the protocol stack, add the needed
 flag to hw_flags. This way we'll also use the new AP probing mechanism.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Fix reporting of RX dma stop failure

 * Correctly report failure to stop RX DMA

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Disable ANI during reset

 * Stop ANI durring reset to prevent false PHY error reports

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Always free tx buffers before reset

 * Always free tx buffers before reset, since we also empty hw queues.
 If we don't and a queue gets stuck, we'll never decrease txq_len and sw
 will keep thinking the queue is still stuck even after reset.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Always write tx powertable on hw

 * By skipping tx power table calibration we also skip setting
 tx power table on hw. Make sure we always write tx power table
 on hw since it gets cleared on reset.

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: speed up AP probing using nullfunc frames

If the nullfunc frame used to probe the AP was not acked, there is no point
in waiting for the probe timeout, so advance to the next try (or disconnect)
immediately.
If we do reach the probe timeout without having received a tx status, the
connection is probably really bad and worth disconnecting.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: remove a redundant check

ieee80211_is_nullfunc() implies ieee80211_is_data()

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

lib: Improve EWMA efficiency by using bitshifts

Using bitshifts instead of division and multiplication should improve
performance. That requires weight and factor to be powers of two, but i think
this is something we can live with.

Thanks to Peter Zijlstra for the improved formula!

Signed-off-by: Bruno Randolf <br1@einfach.org>
--

v2: use log2.h functions
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Use EWMA factor of 1024 instead of 1000

This prepares the only place which uses the EWMA library so far for the
performance improved implementation coming up, which requires factor and
weight to be a power of two.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: Add ATH GENERIC UTILITIES

This file pattern is not currently shown as maintained
by atheros.  Perhaps it should be?

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: Update last_tx_rate only for data frames

The last_tx_rate field was also updated for non-data frames that are
often sent with a lower rate (for example management frames at 1 Mbps).
This is confusing when the data rate is actually much higher.

Hence, only update the last_tx_rate field with tx rate information
gathered from last data frames.

If the rate control algorithm filled in txrc.reported_rate we don't need
to verify this information.

Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6