platform/kernel/u-boot.git
9 years agoodroid: usbhost - Add missing gpio_request call
Suriyan Ramasami [Fri, 21 Nov 2014 01:26:30 +0000 (17:26 -0800)]
odroid: usbhost - Add missing gpio_request call

The USB host code was missing gpio_request() calls before using the gpio
functions, causing errors to be printed out.

As a side note calls to max77686_set_buck_mode(OPMODE_OFF/OPMODE_ON) have
been removed, as they did not have any effect. This is as per Przemyslaw:
I looked into the documentation and there is a "ENB8" pin in PMIC package.
This pin allows steering BUCK8 ON/OFF by the hardware. If ENB8 is set to low
then you can do on/off. If high, then you cannot change its state by I2C
write, which seems to be the case with the Odroids.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoodroid: Update README with USB host usage
Suriyan Ramasami [Fri, 21 Nov 2014 01:26:29 +0000 (17:26 -0800)]
odroid: Update README with USB host usage

Add information wrt using the USB host interface for loading kernel over
ethernet and/or usb mass storage.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoarm: odroid: usb: add support for usb host including ethernet
Suriyan Ramasami [Wed, 29 Oct 2014 16:22:43 +0000 (09:22 -0700)]
arm: odroid: usb: add support for usb host including ethernet

This change adds support for enabling the USB host features of the board.
This includes the USB3503A hub and the SMC LAN9730 ethernet controller
as well.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoarm: odroid: enable/disable usb host phy for exynos4412
Suriyan Ramasami [Wed, 29 Oct 2014 16:22:42 +0000 (09:22 -0700)]
arm: odroid: enable/disable usb host phy for exynos4412

Enable/disable the usb host phy on the odroid U/X2 boards which are based
on the Exynos4412 SOC.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoarm: odroid: pmic77686: allow buck voltage settings
Suriyan Ramasami [Wed, 29 Oct 2014 16:22:41 +0000 (09:22 -0700)]
arm: odroid: pmic77686: allow buck voltage settings

Allow to set the buck voltage for the max77686.
This will be used to reset the SMC LAN9730 ethernet on the odroids.

Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoSMDK2410: convert to generic board
David Müller (ELSOFT AG) [Thu, 30 Oct 2014 08:15:52 +0000 (09:15 +0100)]
SMDK2410: convert to generic board

Compile-time tested only, as I currently don't have access to
the eval board.

Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoexynos: dts: Correct USB vbus-gpio numbering for Snow
Sjoerd Simons [Thu, 6 Nov 2014 10:44:31 +0000 (11:44 +0100)]
exynos: dts: Correct USB vbus-gpio numbering for Snow

The current vbus GPIOs on snow make very little sense, their number is
far above the maximum. As a result, USB doesn't work on snow.

Correct the GPIO numbering so they match the current scheme for exynos5.
Tested both EHCI and XHCI to correctly work after this change.

Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoexynos: Increase command line buffer size (CONFIG_SYS_CBSIZE)
Ian Campbell [Sun, 9 Nov 2014 10:44:33 +0000 (10:44 +0000)]
exynos: Increase command line buffer size (CONFIG_SYS_CBSIZE)

I was running into this limit with a not overly long PXE append line.

Since the PXE code wants to print the resulting command line increase
CONFIG_SYS_PBSIZE too.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoexynos5: Use config_distro_bootcmd.h
Ian Campbell [Sun, 9 Nov 2014 10:44:32 +0000 (10:44 +0000)]
exynos5: Use config_distro_bootcmd.h

This replaces the existing CONFIG_BOOTCOMMAND for exynos5250 and 5420.

exynos4 platforms seem to have existing complex extra env configuration for
booting and so are excluded here. Hence the bootcmd.h is added to
exynos5-common.h.

I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot
tested on arndale.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoexynos: Enable config_distro_defaults.h
Ian Campbell [Sun, 9 Nov 2014 10:44:31 +0000 (10:44 +0000)]
exynos: Enable config_distro_defaults.h

...and remove explicit setting of things which this implies. This is done for
all exynos platforms (4 & 5) so it is added to exynos-common.h

I'm mainly interested in CONFIG_CMD_BOOTZ and CONFIG_SUPPORT_RAW_INITRD

I have build tested on all exynos platforms (MAKEALL -s exynos), but only boot
tested on arndale.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoPeach-Pi: Use the enhanced usb_copy() prototype
Vadim Bendebury [Thu, 13 Nov 2014 17:08:21 +0000 (22:38 +0530)]
Peach-Pi: Use the enhanced usb_copy() prototype

Exynos5800 IROM has a different, from 5250 and 5420, prototype of the
usb_copy() function. Luckily the earlier version did not expect any
arguments, which means the same code could be used with old and new
SoCs, the old ones just ignoring the arguments.

Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoExynos5: ddr3: Choose between single or double channel config
Akshay Saraswat [Thu, 13 Nov 2014 17:08:20 +0000 (22:38 +0530)]
Exynos5: ddr3: Choose between single or double channel config

Add a 4G configuration and choose it based on the number of banks
declared in config file. A board with 4 SDRAM banks declared (as
per CONFIG_NR_DRAM_BANKS) will end up with the 2G confiuration.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoConfig: Exynos5420: Refactor SDRAM Bank and Size
Akshay Saraswat [Thu, 13 Nov 2014 17:08:19 +0000 (22:38 +0530)]
Config: Exynos5420: Refactor SDRAM Bank and Size

Since, not every board may have all memory channels configured
and all available banks of DMC used, we wish to refactor configs
for Memory Bank size and numbers as per board memory config.
For Example, Peach-Pit has 2GB memory and will be using only 4 banks
but Peach-Pi has 3.5GB memory and will be using all 7 available
SDRAM banks.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoDMC: Exynos5: Enable update mode for DREX controller
Alim Akhtar [Thu, 13 Nov 2014 17:08:18 +0000 (22:38 +0530)]
DMC: Exynos5: Enable update mode for DREX controller

As per Exynos5800 UM ver 0.00 section 17.13.2.1
CONCONTROL register bit 3 [update_mode], Exynos5800 does not
support the PHY initiated update. And it is recommanded to
set this field to 1'b1 during initialization. This patch sets this bit.
Applying MC-initiated mode makes DDL tracking ON, that helps in
compensate MIF voltage variation.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoConfig: Exynos5800: Enable build for Peach-Pi
Akshay Saraswat [Thu, 13 Nov 2014 17:08:17 +0000 (22:38 +0530)]
Config: Exynos5800: Enable build for Peach-Pi

This adds following things :
- New config and defconfig for Peach-Pi board.
- Alterations in Kconfig and MAINTAINERS.
- Addition of CONFIG_EXYNOS5800.
- ADdition of exynos5800-peach-pi in dts list.

Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoExynos5800: Add DTS for new board Peach-Pi
Akshay Saraswat [Thu, 13 Nov 2014 17:08:16 +0000 (22:38 +0530)]
Exynos5800: Add DTS for new board Peach-Pi

We have a new board Peach-Pi similar to Peach-Pit. Peach-Pi
differs from Peach-Pit in configuration factors like display
resolution, memory size, SoC version etc.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoExynos5800: Introduce new proid for Exynos5800
Akshay Saraswat [Thu, 13 Nov 2014 17:08:15 +0000 (22:38 +0530)]
Exynos5800: Introduce new proid for Exynos5800

This patch intends to add a new proid for Exynos5800 which is a
variant of Exynos5420. Product id for Exynos5800 is 0x5422.
Both Exynos5420 and Exynos5800 are pin to pin compitable. This
gives us an advantage of reusing Exynos5420 clock, pinmux, memory
and other settings.

Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
9 years agoMerge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Tom Rini [Fri, 14 Nov 2014 21:39:32 +0000 (16:39 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

9 years agoMerge branch 'master' of git://git.denx.de/u-boot-video
Tom Rini [Fri, 14 Nov 2014 20:05:53 +0000 (15:05 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-video

9 years agopowerpc/85xx: enable some P1/P2 boards mtdparts for nor flash
Yangbo Lu [Thu, 16 Oct 2014 02:58:55 +0000 (10:58 +0800)]
powerpc/85xx: enable some P1/P2 boards mtdparts for nor flash

Enable these boards mtdparts for nor flash:
p1020rdb-pd, p1021rdb-pc, p1022ds, p1025twr, and p2020rdb-pc.

Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
9 years agokeymile/powerpc: move to the architecture-generic board system
Valentin Longchamp [Fri, 3 Oct 2014 09:45:24 +0000 (11:45 +0200)]
keymile/powerpc: move to the architecture-generic board system

This converts all the Keymile powerpc boards to the generic board
initialization.

This includes the 3 Keymile powerpc subsystems: km82xx, km83xx,
and kmp204x.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agopowerpc/mpc83xx: Zero boot_flags arg for calling board_init_f()
Valentin Longchamp [Fri, 3 Oct 2014 09:45:23 +0000 (11:45 +0200)]
powerpc/mpc83xx: Zero boot_flags arg for calling board_init_f()

The argument boot_flags of board_init_f() is not used at all in the
powerpc specific board.c init sequence. Now with the generic init
sequence, this boot_flags arg is used by board_init_f().

This patch sets the r3 register that is used to pass the boot_flags
argument from the start.S board_init_f() call to 0 prior to the function
call to avoid unknown content to end up in gd->flags.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agopowerpc/BSC9131RDB: Enable creation of dynamic partitions for NAND
Ashish Kumar [Tue, 7 Oct 2014 12:32:23 +0000 (18:02 +0530)]
powerpc/BSC9131RDB: Enable creation of dynamic partitions for NAND

* fdt_fixup_mtdparts is called from ft_board_setup
 * Run "mtdparts default" to create NAND partition on uboot
 * Use mtdparts to create partitions dynamically rather
    than using static partitions in device tree

Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agopowerpc/BSC9132QDS: Enable creation of dynamic partition for NAND and NOR
Ashish Kumar [Mon, 6 Oct 2014 12:54:56 +0000 (18:24 +0530)]
powerpc/BSC9132QDS: Enable creation of dynamic partition for NAND and NOR

* fdt_fixup_mtdparts is called from ft_board_setup
 * run "mtdparts default" to create NAND, NOR partition on uboot
 * Use mtdparts to create partitions dynamically rather
    than using static partitions in device tree

Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agopowerpc/mpc85xx: Use IFC accessor function
Prabhakar Kushwaha [Tue, 23 Sep 2014 05:27:12 +0000 (10:57 +0530)]
powerpc/mpc85xx: Use IFC accessor function

IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.

So use IFC acessor functions instead of in_be32().

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agot104xrdb: Add Errata A_007662, A_008007 workaround in pbi.cfg
Priyanka Jain [Wed, 17 Sep 2014 10:27:54 +0000 (15:57 +0530)]
t104xrdb: Add Errata A_007662, A_008007 workaround in pbi.cfg

-A_007662 states that for x1 link width, PCIe2 controller trains in
 Gen1 speed while configured for Gen2 speed.
 Workaround:Set the width to x1 and speed to Gen2 by writing to
 CCSR registers in PBI phase

-A_008007 states that PVR register may show random value.
 Workaround: Reset PVR register using DCSR space in PBI phase

Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot

Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agopowerpc/t4rdb: Add support of CPLD
Chunhe Lan [Fri, 12 Sep 2014 06:47:09 +0000 (14:47 +0800)]
powerpc/t4rdb: Add support of CPLD

This support of CPLD includes

    - Files and register definitions
    - Command to switch alternate bank
    - Command to switch default bank

Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years ago85xx/b4:Correct USB DR controller liodn entry
ramneek mehresh [Thu, 21 Aug 2014 12:22:17 +0000 (17:52 +0530)]
85xx/b4:Correct USB DR controller liodn entry

LIODN entry for B4860/B4420 mentions USB controller as "mph"
insread of "dr". This results in PAMU not permitting bus
transactions for USB DR controller on B4860 resulting in
USB function failure. Replacing "fsl-usb2-mph" with
"fsl-usb2-dr" allows USB DR controller bus transactions

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: Sethi Varun-B16395 <Varun.Sethi@freescale.com>
Reviewed-by: Sun Yusong-R58495 <yorksun@freescale.com>
9 years agosbc8548: enable and test CONFIG_SYS_GENERIC_BOARD
Paul Gortmaker [Thu, 14 Aug 2014 14:42:52 +0000 (10:42 -0400)]
sbc8548: enable and test CONFIG_SYS_GENERIC_BOARD

Tested on the following baseline (note "dirty" since I enabled
ALT_BOOT in the config in order to use the alternate boot bank.)

Everything seems to work fine with no additional changes.  The
banner warning message is now gone.

 ---

U-Boot 2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15)

CPU:   8548E, Version: 2.1, (0x80390021)
Core:  e500, Version: 2.2, (0x80210022)
Clock Configuration:
       CPU0:990  MHz,
       CCB:396  MHz,
       DDR:198  MHz (396 MT/s data rate), LBC:99   MHz
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
I2C:   ready
DRAM:  Detected UDIMM
    SDRAM: 128 MiB
256 MiB (DDR2, 64-bit, CL=3, ECC off)
Flash: 72 MiB
L2:    512 KiB enabled
*** Warning - bad CRC, using default environment

PCI: Host, 64 bit, 66 MHz, sync, arbiter
  00:01.0     - 8086:1026 - Network controller
PCI1: Bus 00 - 00

PCIe1: Root Complex, x1 gen1, regs @ 0xe000a000
  02:00.0     - 1148:9e00 - Network controller
PCIe1: Bus 01 - 02
In:    serial
Out:   serial
Err:   serial
Net:   eTSEC0 [PRIME], eTSEC1
Hit any key to stop autoboot:  0
=> ver

U-Boot 2014.10-rc1-00075-ge49f14af1349-dirty (Aug 14 2014 - 10:26:15)
powerpc-linux-gcc (GCC) 4.5.2
GNU ld (GNU Binutils) 2.21
=>

 ---

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agodriver/net/fm/memac_phy: set NEG bit for external MDIOs
Shaohui Xie [Wed, 13 Aug 2014 10:38:09 +0000 (18:38 +0800)]
driver/net/fm/memac_phy: set NEG bit for external MDIOs

NEG bit default is '1' for external MDIOs as per FMAN-v3 RM, but on some
platforms, e.g. T2080QDS, this bit is '0', which leads to MDIO failure
on XAUI PHY, so set this bit definitely to align with the RM.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agoFman/mEMAC: mEMAC fix for 10G MAC and PHY
Shaohui Xie [Wed, 13 Aug 2014 10:32:19 +0000 (18:32 +0800)]
Fman/mEMAC: mEMAC fix for 10G MAC and PHY

1. use Payload length check disable when enable MAC;
2. add XGMII support for setting MAC interface mode;
3. only enable auto negotiation for Non-XGMII mode;
4. return 0xffff if clause 22 is used to read 10G phy_id;

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-By: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agompc85xx/kmp204x: raise u-boot size to 768KB
Valentin Longchamp [Fri, 24 Oct 2014 08:11:16 +0000 (10:11 +0200)]
mpc85xx/kmp204x: raise u-boot size to 768KB

Until now this defined to be 512KB and the total binary size actually
was on the edge of this limit. Most of the powerpc boards have thus
moved to 768KB.

Since on the current kmp204x boards there is 1MB reserved for u-boot on
the SPI boot flash, there is no problem to set the limit to 768KB as
well to be on line with the other powerpc boards and to eventually
configure in some additional features (and binary size) to u-boot.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
9 years agoMerge branch 'master' of git://www.denx.de/git/u-boot-imx
Tom Rini [Fri, 14 Nov 2014 18:53:49 +0000 (13:53 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx

9 years agoarm: mx6: add support for TBS2910 Matrix ARM miniPC
Soeren Moch [Mon, 3 Nov 2014 12:57:01 +0000 (13:57 +0100)]
arm: mx6: add support for TBS2910 Matrix ARM miniPC

Add initial support for TBS2910 Matrix ARM miniPC.
Support includes MMC, Ethernet, UARTs, HDMI, USB, SATA, PCI, I2C, RTC.

Signed-off-by: Soeren Moch <smoch@web.de>
9 years agomx6sabresd: Staticize when possible
Fabio Estevam [Thu, 6 Nov 2014 14:24:25 +0000 (12:24 -0200)]
mx6sabresd: Staticize when possible

Annotate 'static' when appropriate for the variables used locally.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
9 years agomx6sabresd: Fix error handling in board_mmc_init()
Fabio Estevam [Thu, 6 Nov 2014 14:24:24 +0000 (12:24 -0200)]
mx6sabresd: Fix error handling in board_mmc_init()

When an invalid USDHC port is passed we should return -EINVAL instead of 0.

Also, return the error immediately on fsl_esdhc_initialize() failure.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
9 years agomx6: video_skip: Fix crash on NULL pointer
Nikolay Dimitrov [Wed, 5 Nov 2014 08:55:33 +0000 (10:55 +0200)]
mx6: video_skip: Fix crash on NULL pointer

Signed-off-by: Nikolay Dimitrov <picmaster@mail.bg>
Cc: Stefano Babic <sbabic@denx.de>
9 years agoMerge branch 'master' of git://git.denx.de/u-boot-sunxi
Tom Rini [Thu, 13 Nov 2014 15:35:13 +0000 (10:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi

9 years agoimx6: SPL support for iMX6 SabreSD
John Tobias [Wed, 12 Nov 2014 22:27:45 +0000 (14:27 -0800)]
imx6: SPL support for iMX6 SabreSD

This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)

Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
9 years agoimx6: add spl in the header file
John Tobias [Wed, 12 Nov 2014 22:27:44 +0000 (14:27 -0800)]
imx6: add spl in the header file

add the spl info in the header file.
Also, added a macro statement in m6sabre_common.h to avoid compiler
warning.

Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
9 years agokconfig: imx6: add SUPPORT_SPL
John Tobias [Wed, 12 Nov 2014 22:27:43 +0000 (14:27 -0800)]
kconfig: imx6: add SUPPORT_SPL

add SUPPORT_SPL feature for iMX6 SabreSD. It need to use
mx6sabresd_spl_defconfig to compile it.

Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
9 years agoimx6: add data configuration file for SPL
John Tobias [Wed, 12 Nov 2014 22:27:42 +0000 (14:27 -0800)]
imx6: add data configuration file for SPL

It's a trim version of mx6q_4x_mt41j128.cfg. It just removed
the related settings for DDR

Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
9 years agoimx6: add spl config for mx6sabresd
John Tobias [Wed, 12 Nov 2014 22:27:41 +0000 (14:27 -0800)]
imx6: add spl config for mx6sabresd

add a build configuration file for mx6sabresd with spl support

Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
9 years agoimx: mx6q/dlsabreauto: And NAND flash support
Ye.Li [Wed, 12 Nov 2014 06:02:05 +0000 (14:02 +0800)]
imx: mx6q/dlsabreauto: And NAND flash support

The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.

Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
9 years agoimx: mx6q/dl sabre_common: Move MMC ENV offset to 512KB position
Ye.Li [Wed, 12 Nov 2014 06:02:04 +0000 (14:02 +0800)]
imx: mx6q/dl sabre_common: Move MMC ENV offset to 512KB position

Set the CONFIG_ENV_OFFSET from 384KB to 512KB offset, so we will have larger space
for u-boot image.
When enabling NAND flash support feature, the u-boot image size has exceeded the
384KB, which causes overlay to the environment variables storage.

Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
9 years agoot1200: fix card detect for usdhc4
Christian Gmeiner [Tue, 11 Nov 2014 11:57:05 +0000 (12:57 +0100)]
ot1200: fix card detect for usdhc4

Today I got the final board and found out that a different
connector is used as the one on my development board. The
new connector has swaped pins for cd and wp.

This change is tested on a production ready board.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
9 years agomx53loco: Change 'fdt_file' dynamically
Fabio Estevam [Mon, 10 Nov 2014 19:38:19 +0000 (17:38 -0200)]
mx53loco: Change 'fdt_file' dynamically

Since kernel 3.15 there are two dtb's for the imx53-qsb board:

imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC

Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
9 years agoot1200: add support for EHCI
Christian Gmeiner [Mon, 10 Nov 2014 13:35:48 +0000 (14:35 +0100)]
ot1200: add support for EHCI

U-Boot 2014.10-17457-g0b23780-dirty (Nov 10 2014 - 11:41:04)

CPU:   Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: WDOG
Board: ot1200
I2C:   ready
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected M25P16 with page size 256 Bytes, erase size 64 KiB, total 2 MiB
In:    serial
Out:   serial
Err:   serial
Net:   using phy at 0
FEC [PRIME]
Hit any key to stop autoboot:  0
=> usb start
(Re)start USB...
USB0:   Port not available.
USB1:   USB EHCI 1.00
scanning bus 1 for devices... 4 USB Device(s) found
=> usb tree
USB device tree:
  1  Hub (480 Mb/s, 0mA)
  |  u-boot EHCI Host Controller
  |
  +-2  Hub (480 Mb/s, 2mA)
    |
    +-3  Mass Storage (480 Mb/s, 80mA)
    |    USBest Technology USB Mass Storage Device 0000000000028B
    |
    +-4  Vendor specific (480 Mb/s, 2mA)

=>

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
9 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Thu, 13 Nov 2014 14:32:45 +0000 (09:32 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

9 years agoarm: mx6: Fix missing Kconfig option for Novena
Marek Vasut [Thu, 13 Nov 2014 10:06:21 +0000 (11:06 +0100)]
arm: mx6: Fix missing Kconfig option for Novena

Add two missing Kconfig options for Novena and drop the SPL
from the Novena config.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
9 years agosunxi: gmac: Update bananapi fixup to the new CONFIG_TARGET_<BOARD> structure
Zoltan HERPAI [Tue, 11 Nov 2014 12:21:26 +0000 (13:21 +0100)]
sunxi: gmac: Update bananapi fixup to the new CONFIG_TARGET_<BOARD> structure

The magic bit toucher needs to be updated to reflect the new board Kconfig structure

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
9 years agosun6i: ehci: Add sun6i ehci support
Hans de Goede [Fri, 7 Nov 2014 13:51:12 +0000 (14:51 +0100)]
sun6i: ehci: Add sun6i ehci support

Add support for the 2 ehci controllers found on the sun6i (A31) soc.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Marek Vasut <marex@denx.de>
9 years agosunxi: ehci: Add proper Kconfig options to select the usb Vbus gpio-s
Hans de Goede [Fri, 7 Nov 2014 15:09:00 +0000 (16:09 +0100)]
sunxi: ehci: Add proper Kconfig options to select the usb Vbus gpio-s

Add proper Kconfig options to select the usb Vbus gpio-s, besides moving to
Kconfig being the right thing to do, an added advantage of this is that it
allows for boards without Vbus gpio-s.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Add Mele M9 board
Hans de Goede [Mon, 27 Oct 2014 22:29:49 +0000 (23:29 +0100)]
sun6i: Add Mele M9 board

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Enable SPL
Hans de Goede [Sat, 25 Oct 2014 18:18:10 +0000 (20:18 +0200)]
sun6i: Enable SPL

Enable the SPL now that we've all the necessary bits in place.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Poke magic sram controller register to avoid cache issues
Hans de Goede [Sun, 2 Nov 2014 15:55:09 +0000 (16:55 +0100)]
sun6i: Poke magic sram controller register to avoid cache issues

Without this the cache will only work in write-through mode, and as soon as
it is put in write-back mode things break.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Add dram initialization code
Hans de Goede [Sat, 25 Oct 2014 18:27:23 +0000 (20:27 +0200)]
sun6i: Add dram initialization code

Add full support for dram initialization, using a fixed clock and autodetection
of the memory organization (numbers of channels, bus-width, etc.).

This is based on dram_sun6i.c and dram.h from u-boot in the Allwinner A31 SDK,
extended with extra initialization sequences and the autodetect algorithm
from boot0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun4i: Rename dram files to dram_sun4i.x
Hans de Goede [Sun, 2 Nov 2014 19:31:16 +0000 (20:31 +0100)]
sun4i: Rename dram files to dram_sun4i.x

In preparation for adding sun6i dram support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Add cpucfg register definitions
Hans de Goede [Mon, 27 Oct 2014 22:59:27 +0000 (23:59 +0100)]
sun6i: Add cpucfg register definitions

Not used atm, for future use (e.g. PSCI).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Add clock functions needed for SPL / DRAM init
Hans de Goede [Sat, 25 Oct 2014 18:16:33 +0000 (20:16 +0200)]
sun6i: Add clock functions needed for SPL / DRAM init

Add clock_init_safe and clockset_pll5 functions, as these are needed for
SPL support resp. DRAM init (which is needed for SPL too).

Also add some extra clock register constant defines.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agosun6i: Add basic axp221 driver
Oliver Schinagl [Fri, 26 Jul 2013 10:56:58 +0000 (12:56 +0200)]
sun6i: Add basic axp221 driver

The A31 uses the AXP221 pmic for various voltages.

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
--
Changes in v2:
-Rebase
Changes in v3:
-Add support for all dldo and aldo-s
-Add Kconfig option to select building AXP221 and to select voltage of
 dldo and aldo-s
Changes in v4:
-Add axp221_setbits helper function
-Use symbolic names for enabled bits in CTRL1 - CTRL3 registers

9 years agosun6i: Add new p2wi controller driver
Oliver Schinagl [Thu, 25 Jul 2013 12:07:42 +0000 (14:07 +0200)]
sun6i: Add new p2wi controller driver

The A31 uses a new push-pull two wire interface, which features higher
transfer speeds (upto 6 MHz) in theory. While the hardware can burst 8
bytes each time, this driver will only see very little use and thus is
limited to single byte transmission only.

Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
9 years agozynq: zybo: Move CONFIG_DEFAULT_DEVICE_TREE to defconfig
Michal Simek [Thu, 13 Nov 2014 12:22:40 +0000 (13:22 +0100)]
zynq: zybo: Move CONFIG_DEFAULT_DEVICE_TREE to defconfig

This is a MIME GnuPG-signed message.  If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.

Move CONFIG_DEFAULT_DEVICE_TREE from board config
directly to defconfig.

This patch removes compilation warning:
include/configs/zynq_zybo.h:24:0: warning: "CONFIG_DEFAULT_DEVICE_TREE"
redefined [enabled by default]
 #define CONFIG_DEFAULT_DEVICE_TREE zynq-zybo

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9 years agoMerge branch 'zynq' of git://www.denx.de/git/u-boot-microblaze
Tom Rini [Thu, 13 Nov 2014 13:38:17 +0000 (08:38 -0500)]
Merge branch 'zynq' of git://denx.de/git/u-boot-microblaze

9 years agokconfig: arm: move "armv8" define to arch/arm/Kconfig
Masahiro Yamada [Thu, 6 Nov 2014 02:39:27 +0000 (11:39 +0900)]
kconfig: arm: move "armv8" define to arch/arm/Kconfig

Commit 2e07c249a67e (kconfig: arm: introduce symbol for ARM CPUs)
collected the default values of CONFIG_SYS_CPU into arch/arm/Kconfig.

This commit moves "armv8" to there for consistency.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Georges Savoundararadj <savoundg@gmail.com>
9 years agokconfig: arm: select CPU_V7 for some new boards
Masahiro Yamada [Thu, 6 Nov 2014 02:39:26 +0000 (11:39 +0900)]
kconfig: arm: select CPU_V7 for some new boards

This commit adds "select CPU_V7" for some new boards that were not
covered by commit 2e07c249a67e
(kconfig: arm: introduce symbol for ARM CPUs).

Redundant "SYS_CPU" defines and "string" directives should be removed.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Georges Savoundararadj <savoundg@gmail.com>
9 years agoARM: remove unused CPU directory
Masahiro Yamada [Thu, 13 Nov 2014 09:40:07 +0000 (18:40 +0900)]
ARM: remove unused CPU directory

There is no board with CPU "arm_intcm".

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
9 years agokbuild: Make scripts executable
Masahiro Yamada [Thu, 30 Oct 2014 02:06:14 +0000 (11:06 +0900)]
kbuild: Make scripts executable

The Makefiles call the respective interpreter explicitly, but this makes
it easier to use the scripts manually.

(This commit follows commit 06ed5c2bfaca of Linux Kernel)

Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agopowerpc: remove orphaned boards mcc200 and prs200
Nikita Kiryanov [Tue, 11 Nov 2014 13:46:05 +0000 (15:46 +0200)]
powerpc: remove orphaned boards mcc200 and prs200

mcc200 and prs200 are old and have no maintainer. Remove the boards.

This also removes the mcc200 specific 1bpp BMP support from
common/lcd.c

Cc: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
9 years agokm_arm: convert the km_arm boards to the generic board support
Valentin Longchamp [Fri, 3 Oct 2014 09:46:53 +0000 (11:46 +0200)]
km_arm: convert the km_arm boards to the generic board support

This implies that all the km_kirkwood boards and their variants now are
using the generic board init sequence.

Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
9 years agomx28evk: README: Revision C is also supported
Fabio Estevam [Mon, 10 Nov 2014 12:34:26 +0000 (10:34 -0200)]
mx28evk: README: Revision C is also supported

Adjust the text to mention that rev C of the board is also supported.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
9 years agoarm: imx: make bmode command work with SPL/U-Boot combo
Nikita Kiryanov [Wed, 29 Oct 2014 17:28:33 +0000 (19:28 +0200)]
arm: imx: make bmode command work with SPL/U-Boot combo

The bmode command forces the SoC to use a specific boot device
by writing its boot mode into SRC_GPR9, and notifying the SoC of
the change using SRC_GPR10[28] bit: if the bit is on, bootROM
uses the value in SRC_GPR9 instead of SRC_SMBR1 to determine
the boot device.

SPL on the other hand is oblivious to this distinction, so once
the bootROM loads SPL from the device configured in SRC_GPR10,
SPL will attempt to load U-Boot from the device configured in
SRC_SMBR1, which is not updated by the bootROM to the value in
SRC_GPR9.

The result is that the selected boot device is not used across all
the boot stages.

Update spl_boot_device() to look at gpr9 when necessary.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
9 years agomalloc: Output region when debugging
Thierry Reding [Tue, 26 Aug 2014 15:34:22 +0000 (17:34 +0200)]
malloc: Output region when debugging

When DEBUG is set, output memory region used for malloc().

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
9 years agoARM: cache-cp15: Use more accurate types
Thierry Reding [Tue, 26 Aug 2014 15:34:21 +0000 (17:34 +0200)]
ARM: cache-cp15: Use more accurate types

size_t is the canonical type to represent variables that contain a size.
Use it instead of signed integer. Physical addresses can be larger than
32-bit, so use a more appropriate type for them as well. phys_addr_t is
a type that is 32-bit on systems that use 32-bit addresses and 64-bit if
the system is 64-bit or uses a form of physical address extension to use
a larger address space on 32-bit systems. Using these types the same API
can be implemented on a wider range of systems.

Signed-off-by: Thierry Reding <treding@nvidia.com>
9 years agoARM: cache_v7: Various minor cleanups
Thierry Reding [Tue, 26 Aug 2014 15:34:20 +0000 (17:34 +0200)]
ARM: cache_v7: Various minor cleanups

Remove two gratuituous blank lines, uses u32 (instead of int) as the
type for values that will be written to a register, moves the beginning
of the variable declaration section to a separate line (rather than the
one with the opening brace) and keeps the function signature on a single
line where possible.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
9 years agoMerge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Tue, 11 Nov 2014 21:59:44 +0000 (16:59 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga

9 years agoMerge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Tue, 11 Nov 2014 21:59:25 +0000 (16:59 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-usb

9 years agoMerge branch 'master' of git://git.denx.de/u-boot-uniphier
Tom Rini [Tue, 11 Nov 2014 20:49:10 +0000 (15:49 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier

9 years agoRevert "lib: bootm: add missing include"
Michal Simek [Tue, 11 Nov 2014 14:45:36 +0000 (15:45 +0100)]
Revert "lib: bootm: add missing include"

This is a MIME GnuPG-signed message.  If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.

This reverts commit 1e96220a5687efae2aed45ce56e143336c40d0a7.

Remove duplicated vxworks.h header.
The same change was done by
"ARM: prevent compiler warnings from bootm.c"
(sha1: 8d196e52b58d1e50a80c2f5067b201cda521c75c)

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9 years agoARM: UniPhier: call pin_init() also in the normal boot
Masahiro Yamada [Tue, 11 Nov 2014 13:18:22 +0000 (22:18 +0900)]
ARM: UniPhier: call pin_init() also in the normal boot

CONFIG_UNIPHIER_SERIAL has been moved to Kconfig and
it is defined in ./.config but not in spl/.config,
so pin_init() should be called from the normal image
so that UART works correctly.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoARM: UniPhier: consolidate board_postclk_init() function
Masahiro Yamada [Tue, 11 Nov 2014 13:18:21 +0000 (22:18 +0900)]
ARM: UniPhier: consolidate board_postclk_init() function

This commit merges
  arch/arm/cpu/armv7/uniphier/ph1-*/board_postclk_init.c
to
  arch/arm/cpu/armv7/uniphier/board_postclk_init.c

Because PH1-Pro4 does not have the BCU block, add __weak to
bcu_init().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoARM: UniPhier: decrease pre-reloc malloc area size
Masahiro Yamada [Tue, 11 Nov 2014 12:50:41 +0000 (21:50 +0900)]
ARM: UniPhier: decrease pre-reloc malloc area size

In the current implementation of the boot sequence of UniPhier
platform, 32KB temporary RAM is available before relocation.
The malloc area and the stack shares the 32KB area.

With CONFIG_SYS_MALLOC_F_LEN set to 0x7000 (28KB), only 0x1000 (4KB)
is left for the stack.  In some use cases, the system hangs up
with stack over-flow.

Even with driver-model UART enabled, the malloc area of 0x2000 (8KB)
should be enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoARM: UniPhier: add set_pinsel macro for use in assembly code
Masahiro Yamada [Fri, 7 Nov 2014 12:08:52 +0000 (21:08 +0900)]
ARM: UniPhier: add set_pinsel macro for use in assembly code

The function sg_set_pinsel is useful for switching I/O pins
but it can be only used in C code.  This commit adds a simple
macro that is available in asm code.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoARM: UniPhier: enable USB features
Masahiro Yamada [Fri, 7 Nov 2014 09:48:34 +0000 (18:48 +0900)]
ARM: UniPhier: enable USB features

FAT-formated USB storage device access is available.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agousb: UniPhier: add UniPhier on-chip EHCI host driver support
Masahiro Yamada [Fri, 7 Nov 2014 09:48:33 +0000 (18:48 +0900)]
usb: UniPhier: add UniPhier on-chip EHCI host driver support

Support EHCI host driver used on Panasonic UniPhier platform.
Since Device Tree is not supported on UniPhier yet, the base address
of USB cores are passed from board files (platdevice.c).

TODO for me:
Move the base address to device trees.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
9 years agoARM: UniPhier: add MIO register file
Masahiro Yamada [Fri, 7 Nov 2014 09:48:32 +0000 (18:48 +0900)]
ARM: UniPhier: add MIO register file

This commit adds register defines of MIO (Media I/O) block
of UniPhier platform.  This file is necessary to control
the reset signals of the USB cores.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agousb: add basic USB configs in Kconfig
Masahiro Yamada [Fri, 7 Nov 2014 09:48:31 +0000 (18:48 +0900)]
usb: add basic USB configs in Kconfig

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
9 years agoARM: UniPhier: add EHCI host pin settings for PH1-Pro4
Masahiro Yamada [Fri, 7 Nov 2014 09:33:52 +0000 (18:33 +0900)]
ARM: UniPhier: add EHCI host pin settings for PH1-Pro4

These IO pins are necessary for port power control and
over current detect.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoARM: UniPhier: move DDR related configuration to Kconfig
Masahiro Yamada [Thu, 6 Nov 2014 11:16:42 +0000 (20:16 +0900)]
ARM: UniPhier: move DDR related configuration to Kconfig

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoARM: UniPhier: reset on-board devices on start-up
Masahiro Yamada [Wed, 5 Nov 2014 05:25:15 +0000 (14:25 +0900)]
ARM: UniPhier: reset on-board devices on start-up

If a support card is attached to the main board, the on-board
SMSC9118 LAN controller is available.  It must be kept in reset
state for a while on start-up.

When the board is kicked via a debbuger rather than pushing the
hardware reset button, on-board chips are not reset; in this case
the reset signals should be asserted by software.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agoserial: UniPhier: borrow macros from linux/serial_reg.h
Masahiro Yamada [Thu, 30 Oct 2014 03:11:14 +0000 (12:11 +0900)]
serial: UniPhier: borrow macros from linux/serial_reg.h

The same bit-field macros are defined in include/linux/serial_reg.h
so let's include it and delete duplicated defines.

Also, remove unnecessary inclusion of <common.h>.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
9 years agokconfig: zynq: Add ZYBO board
Peter Crosthwaite [Thu, 28 Aug 2014 11:16:41 +0000 (21:16 +1000)]
kconfig: zynq: Add ZYBO board

Add a defconfig and Kconfigury for the Digilent ZYBO board.

Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9 years agoconfigs: zynq: Add config support for ZYBO
Tinghui Wang [Thu, 28 Aug 2014 11:16:40 +0000 (21:16 +1000)]
configs: zynq: Add config support for ZYBO

This patch adds config support needed for ZYBO target and has
been tested on Rev. B ZYBO hardware.

Signed-off-by: Tinghui Wang <steven.wang@digilentinc.com>
[PC changes:
 * Dropped boards.cfg change (rebase conflict)
 * Dropped custom u-boot env
 * Added DTS
 * Misc forward-porting changes
]
Signed-off-by: Peter Crosthwiate <crosthwaite.peter@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9 years agoarm: dts: zynq: Add digilent ZYBO board dts
Peter Crosthwaite [Thu, 28 Aug 2014 11:16:39 +0000 (21:16 +1000)]
arm: dts: zynq: Add digilent ZYBO board dts

It's a Zynq board similar in design to the currently supported ones.
512MB of RAM and UART1 is used.

Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9 years agozynq: Use GPLed files for SPL
Soren Brinkmann [Thu, 30 Oct 2014 17:52:43 +0000 (10:52 -0700)]
zynq: Use GPLed files for SPL

The latest Xilinx tools generate ps7_init files that are explicitly
available under GPL. Change the makefile to allow drop in of those files
for building the SPL.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Reviewed-and-tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
9 years agoPrepare v2015.01-rc1 v2015.01-rc1
Tom Rini [Mon, 10 Nov 2014 21:19:51 +0000 (16:19 -0500)]
Prepare v2015.01-rc1

Signed-off-by: Tom Rini <trini@ti.com>
9 years agoMerge branch 'master' of git://git.denx.de/u-boot-i2c
Tom Rini [Mon, 10 Nov 2014 14:20:52 +0000 (09:20 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c

9 years agoMerge branch 'master' of git://git.denx.de/u-boot-blackfin
Tom Rini [Mon, 10 Nov 2014 14:20:38 +0000 (09:20 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin

9 years agoMerge branch 'master' of git://git.denx.de/u-boot-arm
Tom Rini [Sat, 8 Nov 2014 01:35:20 +0000 (20:35 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm

9 years agoAdded support for comments in input to mkenvimage.
Dominik Muth [Thu, 28 Aug 2014 10:25:27 +0000 (12:25 +0200)]
Added support for comments in input to mkenvimage.

This patch adds support for comments in the input to mkenvimage, i.e. in
the environment source: All lines starting with a # in the firs column
will be ignored.

Additionally empty lines will also be ignored.

Signed-off-by: Dominik Muth <dominik.muth@bkvibro.com>