Btrfs: clean up resources during umount after trans is aborted

[ Upstream commit af7227338135d2f1b1552bf9a6d43e02dcba10b9 ]

Currently if some fatal errors occur, like all IO get -EIO, resources
would be cleaned up when
a) transaction is being committed or
b) BTRFS_FS_STATE_ERROR is set

However, in some rare cases, resources may be left alone after transaction
gets aborted and umount may run into some ASSERT(), e.g.
ASSERT(list_empty(&block_group->dirty_list));

For case a), in btrfs_commit_transaciton(), there're several places at the
beginning where we just call btrfs_end_transaction() without cleaning up
resources.  For case b), it is possible that the trans handle doesn't have
any dirty stuff, then only trans hanlde is marked as aborted while
BTRFS_FS_STATE_ERROR is not set, so resources remain in memory.

This makes btrfs also check BTRFS_FS_STATE_TRANS_ABORTED to make sure that
all resources won't stay in memory after umount.

Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme: don't send keep-alives to the discovery controller

[ Upstream commit 74c6c71530847808d4e3be7b205719270efee80c ]

NVMe over Fabrics 1.0 Section 5.2 "Discovery Controller Properties and
Command Support" Figure 31 "Discovery Controller – Admin Commands"
explicitly listst all commands but "Get Log Page" and "Identify" as
reserved, but NetApp report the Linux host is sending Keep Alive
commands to the discovery controller, which is a violation of the
Spec.

We're already checking for discovery controllers when configuring the
keep alive timeout but when creating a discovery controller we're not
hard wiring the keep alive timeout to 0 and thus remain on
NVME_DEFAULT_KATO for the discovery controller.

This can be easily remproduced when issuing a direct connect to the
discovery susbsystem using:
'nvme connect [...] --nqn=nqn.2014-08.org.nvmexpress.discovery'

Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 07bfcd09a288 ("nvme-fabrics: add a generic NVMe over Fabrics library")
Reported-by: Martin George <marting@netapp.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

firmware: dmi_scan: Fix UUID length safety check

[ Upstream commit 90fe6f8ff00a07641ca893d64f75ca22ce77cca2 ]

The test which ensures that the DMI type 1 structure is long enough
to hold the UUID is off by one. It would fail if the structure is
exactly 24 bytes long, while that's sufficient to hold the UUID.

I don't expect this bug to cause problem in practice because all
implementations I have seen had length 8, 25 or 27 bytes, in line
with the SMBIOS specifications. But let's fix it still.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: a814c3597a6b ("firmware: dmi_scan: Check DMI structure length")
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sh: fix debug trap failure to process signals before return to user

[ Upstream commit 96a598996f6ac518ac79839ecbb17c91af91f4f7 ]

When responding to a debug trap (breakpoint) in userspace, the
kernel's trap handler raised SIGTRAP but returned from the trap via a
code path that ignored pending signals, resulting in an infinite loop
re-executing the trapping instruction.

Signed-off-by: Rich Felker <dalias@libc.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mvneta: fix enable of all initialized RXQs

[ Upstream commit e81b5e01c14add8395dfba7130f8829206bb507d ]

In mvneta_port_up() we enable relevant RX and TX port queues by write
queues bit map to an appropriate register.

q_map must be ZERO in the beginning of this process.

Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vlan: Fix vlan insertion for packets without ethernet header

[ Upstream commit c769accdf3d8a103940bea2979b65556718567e9 ]

In some situation vlan packets do not have ethernet headers. One example
is packets from tun devices. Users can specify vlan protocol in tun_pi
field instead of IP protocol. When we have a vlan device with reorder_hdr
disabled on top of the tun device, such packets from tun devices are
untagged in skb_vlan_untag() and vlan headers will be inserted back in
vlan_insert_inner_tag().

vlan_insert_inner_tag() however did not expect packets without ethernet
headers, so in such a case size argument for memmove() underflowed.

We don't need to copy headers for packets which do not have preceding
headers of vlan headers, so skip memmove() in that case.
Also don't write vlan protocol in skb->data when it does not have enough
room for it.

Fixes: cbe7128c4b92 ("vlan: Fix out of order vlan headers with reorder header off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Fix untag for vlan packets without ethernet header

[ Upstream commit ae4745730cf8e693d354ccd4dbaf59ea440c09a9 ]

In some situation vlan packets do not have ethernet headers. One example
is packets from tun devices. Users can specify vlan protocol in tun_pi
field instead of IP protocol, and skb_vlan_untag() attempts to untag such
packets.

skb_vlan_untag() (more precisely, skb_reorder_vlan_header() called by it)
however did not expect packets without ethernet headers, so in such a case
size argument for memmove() underflowed and triggered crash.

====
BUG: unable to handle kernel paging request at ffff8801cccb8000
IP: __memmove+0x24/0x1a0 arch/x86/lib/memmove_64.S:43
PGD 9cee067 P4D 9cee067 PUD 1d9401063 PMD 1cccb7063 PTE 2810100028101
Oops: 000b [#1] SMP KASAN
Dumping ftrace buffer:
   (ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 17663 Comm: syz-executor2 Not tainted 4.16.0-rc7+ #368
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:__memmove+0x24/0x1a0 arch/x86/lib/memmove_64.S:43
RSP: 0018:ffff8801cc046e28 EFLAGS: 00010287
RAX: ffff8801ccc244c4 RBX: fffffffffffffffe RCX: fffffffffff6c4c2
RDX: fffffffffffffffe RSI: ffff8801cccb7ffc RDI: ffff8801cccb8000
RBP: ffff8801cc046e48 R08: ffff8801ccc244be R09: ffffed0039984899
R10: 0000000000000001 R11: ffffed0039984898 R12: ffff8801ccc244c4
R13: ffff8801ccc244c0 R14: ffff8801d96b7c06 R15: ffff8801d96b7b40
FS:  00007febd562d700(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff8801cccb8000 CR3: 00000001ccb2f006 CR4: 00000000001606e0
DR0: 0000000020000000 DR1: 0000000020000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000600
Call Trace:
 memmove include/linux/string.h:360 [inline]
 skb_reorder_vlan_header net/core/skbuff.c:5031 [inline]
 skb_vlan_untag+0x470/0xc40 net/core/skbuff.c:5061
 __netif_receive_skb_core+0x119c/0x3460 net/core/dev.c:4460
 __netif_receive_skb+0x2c/0x1b0 net/core/dev.c:4627
 netif_receive_skb_internal+0x10b/0x670 net/core/dev.c:4701
 netif_receive_skb+0xae/0x390 net/core/dev.c:4725
 tun_rx_batched.isra.50+0x5ee/0x870 drivers/net/tun.c:1555
 tun_get_user+0x299e/0x3c20 drivers/net/tun.c:1962
 tun_chr_write_iter+0xb9/0x160 drivers/net/tun.c:1990
 call_write_iter include/linux/fs.h:1782 [inline]
 new_sync_write fs/read_write.c:469 [inline]
 __vfs_write+0x684/0x970 fs/read_write.c:482
 vfs_write+0x189/0x510 fs/read_write.c:544
 SYSC_write fs/read_write.c:589 [inline]
 SyS_write+0xef/0x220 fs/read_write.c:581
 do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x454879
RSP: 002b:00007febd562cc68 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007febd562d6d4 RCX: 0000000000454879
RDX: 0000000000000157 RSI: 0000000020000180 RDI: 0000000000000014
RBP: 000000000072bea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000000006b0 R14: 00000000006fc120 R15: 0000000000000000
Code: 90 90 90 90 90 90 90 48 89 f8 48 83 fa 20 0f 82 03 01 00 00 48 39 fe 7d 0f 49 89 f0 49 01 d0 49 39 f8 0f 8f 9f 00 00 00 48 89 d1 <f3> a4 c3 48 81 fa a8 02 00 00 72 05 40 38 fe 74 3b 48 83 ea 20
RIP: __memmove+0x24/0x1a0 arch/x86/lib/memmove_64.S:43 RSP: ffff8801cc046e28
CR2: ffff8801cccb8000
====

We don't need to copy headers for packets which do not have preceding
headers of vlan headers, so skip memmove() in that case.

Fixes: 4bbb3e0e8239 ("net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off")
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qede: Do not drop rx-checksum invalidated packets.

[ Upstream commit 58f101bf87e32753342a6924772c6ebb0fbde24a ]

Today, driver drops received packets which are indicated as
invalid checksum by the device. Instead of dropping such packets,
pass them to the stack with CHECKSUM_NONE indication in skb.

Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: enable multicast if necessary

[ Upstream commit f03dbb06dc380274e351ca4b1ee1587ed4529e62 ]

My recent change to netvsc drive in how receive flags are handled
broke multicast.  The Hyper-v/Azure virtual interface there is not a
multicast filter list, filtering is only all or none. The driver must
enable all multicast if any multicast address is present.

Fixes: 009f766ca238 ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/kmemleak.c: wait for scan completion before disabling free

[ Upstream commit 914b6dfff790544d9b77dfd1723adb3745ec9700 ]

A crash is observed when kmemleak_scan accesses the object->pointer,
likely due to the following race.

  TASK A             TASK B                     TASK C
  kmemleak_write
   (with "scan" and
   NOT "scan=on")
  kmemleak_scan()
                     create_object
                     kmem_cache_alloc fails
                     kmemleak_disable
                     kmemleak_do_cleanup
                     kmemleak_free_enabled = 0
                                                kfree
                                                kmemleak_free bails out
                                                 (kmemleak_free_enabled is 0)
                                                slub frees object->pointer
  update_checksum
  crash - object->pointer
   freed (DEBUG_PAGEALLOC)

kmemleak_do_cleanup waits for the scan thread to complete, but not for
direct call to kmemleak_scan via kmemleak_write.  So add a wait for
kmemleak_scan completion before disabling kmemleak_free, and while at it
fix the comment on stop_scan_thread.

[vinmenon@codeaurora.org: fix stop_scan_thread comment]
Link: http://lkml.kernel.org/r/1522219972-22809-1-git-send-email-vinmenon@codeaurora.org
Link: http://lkml.kernel.org/r/1522063429-18992-1-git-send-email-vinmenon@codeaurora.org
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/vmstat.c: fix vmstat_update() preemption BUG

[ Upstream commit c7f26ccfb2c31eb1bf810ba13d044fcf583232db ]

Attempting to hotplug CPUs with CONFIG_VM_EVENT_COUNTERS enabled can
cause vmstat_update() to report a BUG due to preemption not being
disabled around smp_processor_id().

Discovered on Ubiquiti EdgeRouter Pro with Cavium Octeon II processor.

  BUG: using smp_processor_id() in preemptible [00000000] code:
  kworker/1:1/269
  caller is vmstat_update+0x50/0xa0
  CPU: 0 PID: 269 Comm: kworker/1:1 Not tainted
  4.16.0-rc4-Cavium-Octeon-00009-gf83bbd5-dirty #1
  Workqueue: mm_percpu_wq vmstat_update
  Call Trace:
    show_stack+0x94/0x128
    dump_stack+0xa4/0xe0
    check_preemption_disabled+0x118/0x120
    vmstat_update+0x50/0xa0
    process_one_work+0x144/0x348
    worker_thread+0x150/0x4b8
    kthread+0x110/0x140
    ret_from_kernel_thread+0x14/0x1c

Link: http://lkml.kernel.org/r/1520881552-25659-1-git-send-email-steven.hill@cavium.com
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/page_owner: fix recursion bug after changing skip entries

[ Upstream commit 299815a4fba9f3c7a81434dba0072148f1690608 ]

This patch fixes commit 5f48f0bd4e36 ("mm, page_owner: skip unnecessary
stack_trace entries").

Because if we skip first two entries then logic of checking count value
as 2 for recursion is broken and code will go in one depth recursion.

so we need to check only one call of _RET_IP(__set_page_owner) while
checking for recursion.

Current Backtrace while checking for recursion:-

  (save_stack)             from (__set_page_owner)  // (But recursion returns true here)
  (__set_page_owner)       from (get_page_from_freelist)
  (get_page_from_freelist) from (__alloc_pages_nodemask)
  (__alloc_pages_nodemask) from (depot_save_stack)
  (depot_save_stack)       from (save_stack)       // recursion should return true here
  (save_stack)             from (__set_page_owner)
  (__set_page_owner)       from (get_page_from_freelist)
  (get_page_from_freelist) from (__alloc_pages_nodemask+)
  (__alloc_pages_nodemask) from (depot_save_stack)
  (depot_save_stack)       from (save_stack)
  (save_stack)             from (__set_page_owner)
  (__set_page_owner)       from (get_page_from_freelist)

Correct Backtrace with fix:

  (save_stack)             from (__set_page_owner) // recursion returned true here
  (__set_page_owner)       from (get_page_from_freelist)
  (get_page_from_freelist) from (__alloc_pages_nodemask+)
  (__alloc_pages_nodemask) from (depot_save_stack)
  (depot_save_stack)       from (save_stack)
  (save_stack)             from (__set_page_owner)
  (__set_page_owner)       from (get_page_from_freelist)

Link: http://lkml.kernel.org/r/1521607043-34670-1-git-send-email-maninder1.s@samsung.com
Fixes: 5f48f0bd4e36 ("mm, page_owner: skip unnecessary stack_trace entries")
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@techadventures.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ayush Mittal <ayush.m@samsung.com>
Cc: Prakash Gupta <guptap@codeaurora.org>
Cc: Vinayak Menon <vinmenon@codeaurora.org>
Cc: Vasyl Gomonovych <gomonovych@gmail.com>
Cc: Amit Sahrawat <a.sahrawat@samsung.com>
Cc: <pankaj.m@samsung.com>
Cc: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, slab: memcg_link the SLAB's kmem_cache

[ Upstream commit 880cd276dff17ea29e9a8404275c9502b265afa7 ]

All the root caches are linked into slab_root_caches which was
introduced by the commit 510ded33e075 ("slab: implement slab_root_caches
list") but it missed to add the SLAB's kmem_cache.

While experimenting with opt-in/opt-out kmem accounting, I noticed
system crashes due to NULL dereference inside cache_from_memcg_idx()
while deferencing kmem_cache.memcg_params.memcg_caches.  The upstream
clean kernel will not see these crashes but SLAB should be consistent
with SLUB which does linked its boot caches (kmem_cache_node and
kmem_cache) into slab_root_caches.

Link: http://lkml.kernel.org/r/20180319210020.60289-1-shakeelb@google.com
Fixes: 510ded33e075c ("slab: implement slab_root_caches list")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qede: Fix barrier usage after tx doorbell write.

[ Upstream commit b9fc828debc8ac2bb21b5819a44d2aea456f1c95 ]

Since commit c5ad119fb6c09b0297446be05bd66602fa564758
("net: sched: pfifo_fast use skb_array") driver is exposed
to an issue where it is hitting NULL skbs while handling TX
completions. Driver uses mmiowb() to flush the writes to the
doorbell bar which is a write-combined bar, however on x86
mmiowb() does not flush the write combined buffer.

This patch fixes this problem by replacing mmiowb() with wmb()
after the write combined doorbell write so that writes are
flushed and synchronized from more than one processor.

V1->V2:
-------
This patch was marked as "superseded" in patchwork.
(Not really sure for what reason).Resending it as v2.

Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

builddeb: Fix header package regarding dtc source links

[ Upstream commit f8437520704cfd9cc442a99d73ed708a3cdadaf9 ]

Since d5d332d3f7e8, a couple of links in scripts/dtc/include-prefixes
are additionally required in order to build device trees with the header
package.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

llc: properly handle dev_queue_xmit() return value

[ Upstream commit b85ab56c3f81c5a24b5a5213374f549df06430da ]

llc_conn_send_pdu() pushes the skb into write queue and
calls llc_conn_send_pdus() to flush them out. However, the
status of dev_queue_xmit() is not returned to caller,
in this case, llc_conn_state_process().

llc_conn_state_process() needs hold the skb no matter
success or failure, because it still uses it after that,
therefore we should hold skb before dev_queue_xmit() when
that skb is the one being processed by llc_conn_state_process().

For other callers, they can just pass NULL and ignore
the return value as they are.

Reported-by: Noam Rathaus <noamr@beyondsecurity.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/alternatives: Fixup alternative_call_2

[ Upstream commit bd6271039ee6f0c9b468148fc2d73e0584af6b4f ]

The following pattern fails to compile while the same pattern
with alternative_call() does:

if (...)
alternative_call_2(...);
else
alternative_call_2(...);

as it expands into

if (...)
{
}; <===
else
{
};

Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20180114120504.GA11368@avx2
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel: Fix linear IP of PEBS real_ip on Haswell and later CPUs

[ Upstream commit 71eb9ee9596d8df3d5723c3cfc18774c6235e8b1 ]

this patch fix a bug in how the pebs->real_ip is handled in the PEBS
handler. real_ip only exists in Haswell and later processor. It is
actually the eventing IP, i.e., where the event occurred. As opposed
to the pebs->ip which is the PEBS interrupt IP which is always off
by one.

The problem is that the real_ip just like the IP needs to be fixed up
because PEBS does not record all the machine state registers, and
in particular the code segement (cs). This is why we have the set_linear_ip()
function. The problem was that set_linear_ip() was only used on the pebs->ip
and not the pebs->real_ip.

We have profiles which ran into invalid callstacks because of this.
Here is an example:

 .....  0: ffffffffffffff80 recent entry, marker kernel v
 .....  1: 000000000040044d <= user address in kernel space!
 .....  2: fffffffffffffe00 marker enter user v
 .....  3: 000000000040044d
 .....  4: 00000000004004b6 oldest entry

Debugging output in get_perf_callchain():

 [  857.769909] CALLCHAIN: CPU8 ip=40044d regs->cs=10 user_mode(regs)=0

The problem is that the kernel entry in 1: points to a user level
address. How can that be?

The reason is that with PEBS sampling the instruction that caused the event
to occur and the instruction where the CPU was when the interrupt was posted
may be far apart. And sometime during that time window, the privilege level may
change. This happens, for instance, when the PEBS sample is taken close to a
kernel entry point. Here PEBS, eventing IP (real_ip) captured a user level
instruction. But by the time the PMU interrupt fired, the processor had already
entered kernel space. This is why the debug output shows a user address with
user_mode() false.

The problem comes from PEBS not recording the code segment (cs) register.
The register is used in x86_64 to determine if executing in kernel vs user
space. This is okay because the kernel has a software workaround called
set_linear_ip(). But the issue in setup_pebs_sample_data() is that
set_linear_ip() is never called on the real_ip value when it is available
(Haswell and later) and precise_ip > 1.

This patch fixes this problem and eliminates the callchain discrepancy.

The patch restructures the code around set_linear_ip() to minimize the number
of times the IP has to be set.

Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: kan.liang@intel.com
Link: http://lkml.kernel.org/r/1521788507-10231-1-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5: Make eswitch support to depend on switchdev

[ Upstream commit f125376b06bcc57dfb0216ac8d6ec6d5dcf81025 ]

Add dependancy for switchdev to be congfigured as any user-space control
plane SW is expected to use the HW switchdev ID to locate the representors
related to VFs of a certain PF and apply SW/offloaded switching on them.

Fixes: e80541ecabd5 ('net/mlx5: Add CONFIG_MLX5_ESWITCH Kconfig')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: mt7530: fix module autoloading for OF platform drivers

[ Upstream commit 3c82b372a9f44aa224b8d5106ff6f1ad516fa8a8 ]

It's required to create a modules.alias via MODULE_DEVICE_TABLE helper
for the OF platform driver. Otherwise, module autoloading cannot work.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: fix the err path for dev hwaddr sync in bond_enslave

[ Upstream commit 5c78f6bfae2b10ff70e21d343e64584ea6280c26 ]

vlan_vids_add_by_dev is called right after dev hwaddr sync, so on
the err path it should unsync dev hwaddr. Otherwise, the slave
dev's hwaddr will never be unsync when this err happens.

Fixes: 1ff412ad7714 ("bonding: change the bond's vlan syncing functions with the standard ones")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qmi_wwan: add BroadMobi BM806U 2020:2033

[ Upstream commit 743989254ea9f132517806d8893ca9b6cf9dc86b ]

BroadMobi BM806U is an Qualcomm MDM9225 based 3G/4G modem.
Tested hardware BM806U is mounted on D-Link DWR-921-C3 router.
The USB id is added to qmi_wwan.c to allow QMI communication with
the BM806U.

Tested on 4.14 kernel and OpenWRT.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lan78xx: Set ASD in MAC_CR when EEE is enabled.

[ Upstream commit e69647a19c870c2f919e4d5023af8a515e8ef25f ]

Description:
EEE does not work with lan7800 when AutoSpeed is not set.
(This can happen when EEPROM is not populated or configured incorrectly)

Root-Cause:
When EEE is enabled, the mac config register ASD is not set
i.e. in default state, causing EEE fail.

Fix:
Set the register when eeprom is not present.

Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Raghuram Chary J <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 8748/1: mm: Define vdso_start, vdso_end as array

[ Upstream commit 73b9160d0dfe44dfdaffd6465dc1224c38a4a73c ]

Define vdso_start, vdso_end as array to avoid compile-time analysis error
for the case of built with CONFIG_FORTIFY_SOURCE.

and, since vdso_start, vdso_end are used in vdso.c only,
move extern-declaration from vdso.h to vdso.c.

If kernel is built with CONFIG_FORTIFY_SOURCE,
compile-time error happens at this code.
- if (memcmp(&vdso_start, "177ELF", 4))

The size of "&vdso_start" is recognized as 1 byte, but n is 4,
So that compile-time error is reported.

Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix packet loss for broadcasted DHCP packets to a server

[ Upstream commit a752c0a4524889cdc0765925258fd1fd72344100 ]

DHCP connectivity issues can currently occur if the following conditions
are met:

1) A DHCP packet from a client to a server
2) This packet has a multicast destination
3) This destination has a matching entry in the translation table
   (FF:FF:FF:FF:FF:FF for IPv4, 33:33:00:01:00:02/33:33:00:01:00:03
    for IPv6)
4) The orig-node determined by TT for the multicast destination
   does not match the orig-node determined by best-gateway-selection

In this case the DHCP packet will be dropped.

The "gateway-out-of-range" check is supposed to only be applied to
unicasted DHCP packets to a specific DHCP server.

In that case dropping the the unicasted frame forces the client to
retry via a broadcasted one, but now directed to the new best
gateway.

A DHCP packet with broadcast/multicast destination is already ensured to
always be delivered to the best gateway. Dropping a multicasted
DHCP packet here will only prevent completing DHCP as there is no
other fallback.

So far, it seems the unicast check was implicitly performed by
expecting the batadv_transtable_search() to return NULL for multicast
destinations. However, a multicast address could have always ended up in
the translation table and in fact is now common.

To fix this potential loss of a DHCP client-to-server packet to a
multicast address this patch adds an explicit multicast destination
check to reliably bail out of the gateway-out-of-range check for such
destinations.

The issue and fix were tested in the following three node setup:

- Line topology, A-B-C
- A: gateway client, DHCP client
- B: gateway server, hop-penalty increased: 30->60, DHCP server
- C: gateway server, code modifications to announce FF:FF:FF:FF:FF:FF

Without this patch, A would never transmit its DHCP Discover packet
due to an always "out-of-range" condition. With this patch,
a full DHCP handshake between A and B was possible again.

Fixes: be7af5cf9cae ("batman-adv: refactoring gateway handling code")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix multicast-via-unicast transmission with AP isolation

[ Upstream commit f8fb3419ead44f9a3136995acd24e35da4525177 ]

For multicast frames AP isolation is only supposed to be checked on
the receiving nodes and never on the originating one.

Furthermore, the isolation or wifi flag bits should only be intepreted
as such for unicast and never multicast TT entries.

By injecting flags to the multicast TT entry claimed by a single
target node it was verified in tests that this multicast address
becomes unreachable, leading to packet loss.

Omitting the "src" parameter to the batadv_transtable_search() call
successfully skipped the AP isolation check and made the target
reachable again.

Fixes: 1d8ab8d3c176 ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdkfd: Fix scratch memory with HWS enabled

[ Upstream commit c70a36268799cf2f902b5a31e452571fcb96bfe9 ]

Program sh_hidden_private_base_vmid correctly in the map-process
PM4 packet.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: ftrace: Add a testcase for probepoint

[ Upstream commit dfa453bc90eca0febff33c8d292a656e53702158 ]

Add a testcase for probe point definition. This tests
symbol, address and symbol+offset syntax. The offset
must be positive and smaller than UINT_MAX.

Link: http://lkml.kernel.org/r/152129043097.31874.14273580606301767394.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: ftrace: Add a testcase for string type with kprobe_event

[ Upstream commit 5fbdbed797b6d12d043a5121fdbc8d8b49d10e80 ]

Add a testcase for string type with kprobe event.
This tests good/bad syntax combinations and also
the traced data is correct in several way.

Link: http://lkml.kernel.org/r/152129038381.31874.9201387794548737554.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: ftrace: Add probe event argument syntax testcase

[ Upstream commit 871bef2000968c312a4000b2f56d370dcedbc93c ]

Add a testcase for probe event argument syntax which
ensures the kprobe_events interface correctly parses
given event arguments.

Link: http://lkml.kernel.org/r/152129033679.31874.12705519603869152799.stgit@devbox
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: Fix transport mode skb control buffer usage.

[ Upstream commit 9a3fb9fb84cc30577c1b012a6a3efda944684291 ]

A recent commit introduced a new struct xfrm_trans_cb
that is used with the sk_buff control buffer. Unfortunately
it placed the structure in front of the control buffer and
overlooked that the IPv4/IPv6 control buffer is still needed
for some layer 4 protocols. As a result the IPv4/IPv6 control
buffer is overwritten with this structure. Fix this by setting
a apropriate header in front of the structure.

Fixes acf568ee859f ("xfrm: Reinject transport-mode packets ...")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, thp: do not cause memcg oom for thp

[ Upstream commit 9d3c3354bb85bab4d865fe95039443f09a4c8394 ]

Commit 2516035499b9 ("mm, thp: remove __GFP_NORETRY from khugepaged and
madvised allocations") changed the page allocator to no longer detect
thp allocations based on __GFP_NORETRY.

It did not, however, modify the mem cgroup try_charge() path to avoid
oom kill for either khugepaged collapsing or thp faulting.  It is never
expected to oom kill a process to allocate a hugepage for thp; reclaim
is governed by the thp defrag mode and MADV_HUGEPAGE, but allocations
(and charging) should fallback instead of oom killing processes.

Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1803191409420.124411@chino.kir.corp.google.com
Fixes: 2516035499b9 ("mm, thp: remove __GFP_NORETRY from khugepaged and madvised allocations")
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/mempolicy.c: avoid use uninitialized preferred_node

[ Upstream commit 8970a63e965b43288c4f5f40efbc2bbf80de7f16 ]

Alexander reported a use of uninitialized memory in __mpol_equal(),
which is caused by incorrect use of preferred_node.

When mempolicy in mode MPOL_PREFERRED with flags MPOL_F_LOCAL, it uses
numa_node_id() instead of preferred_node, however, __mpol_equal() uses
preferred_node without checking whether it is MPOL_F_LOCAL or not.

[akpm@linux-foundation.org: slight comment tweak]
Link: http://lkml.kernel.org/r/4ebee1c2-57f6-bcb8-0e2d-1833d1ee0bb7@huawei.com
Fixes: fc36b8d3d819 ("mempolicy: use MPOL_F_LOCAL to Indicate Preferred Local Policy")
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/ast: Fixed 1280x800 Display Issue

[ Upstream commit 5a9f698feb11b198f17b2acebbfe0e2716a3beed ]

The original ast driver cannot display properly if the resolution is 1280x800 and the pixel clock is 83.5MHz.
Here is the update to fix it.

Signed-off-by: Y.C. Chen <yc_chen@aspeedtech.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: Fix functional dsa-loop dependency on FIXED_PHY

[ Upstream commit 40013ff20b1beed31184935fc0aea6a859d4d4ef ]

We have a functional dependency on the FIXED_PHY MDIO bus because we register
fixed PHY devices "the old way" which only works if the code that does this has
had a chance to run before the fixed MDIO bus is probed. Make sure we account
for that and have dsa_loop_bdinfo.o be either built-in or modular depending on
whether CONFIG_FIXED_PHY reflects that too.

Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix idr leak in the error path of tcf_skbmod_init()

[ Upstream commit f29cdfbe33d6915ba8056179b0041279a67e3647 ]

tcf_skbmod_init() can fail after the idr has been successfully reserved.
When this happens, every subsequent attempt to configure skbmod rules
using the same idr value will systematically fail with -ENOSPC, unless
the first attempt was done using the 'replace' keyword:

 # tc action add action skbmod swap mac index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action add action skbmod swap mac index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 # tc action add action skbmod swap mac index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 ...

Fix this in tcf_skbmod_init(), ensuring that tcf_idr_release() is called
on the error path when the idr has been reserved, but not yet inserted.
Also, don't test 'ovr' in the error path, to avoid a 'replace' failure
implicitly become a 'delete' that leaks refcount in act_skbmod module:

 # rmmod act_skbmod; modprobe act_skbmod
 # tc action add action skbmod swap mac index 100
 # tc action add action skbmod swap mac continue index 100
 RTNETLINK answers: File exists
 We have an error talking to the kernel
 # tc action replace action skbmod swap mac continue index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action list action skbmod
 #
 # rmmod  act_skbmod
 rmmod: ERROR: Module act_skbmod is in use

Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix idr leak in the error path of __tcf_ipt_init()

[ Upstream commit 1e46ef1762bb2e52f0f996131a4d16ed4e9fd065 ]

__tcf_ipt_init() can fail after the idr has been successfully reserved.
When this happens, subsequent attempts to configure xt/ipt rules using
the same idr value systematically fail with -ENOSPC:

 # tc action add action xt -j LOG --log-prefix test1 index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "test1" index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 Command "(null)" is unknown, try "tc actions help".
 # tc action add action xt -j LOG --log-prefix test1 index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "test1" index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 Command "(null)" is unknown, try "tc actions help".
 # tc action add action xt -j LOG --log-prefix test1 index 100
 tablename: mangle hook: NF_IP_POST_ROUTING
         target:  LOG level warning prefix "test1" index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 ...

Fix this in the error path of __tcf_ipt_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup(). Since tcf_ipt_release() can now be called
when tcfi_t is NULL, we also need to protect calls to ipt_destroy_target()
to avoid NULL pointer dereference.

Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix idr leak in the error path of tcp_pedit_init()

[ Upstream commit 94fa3f929ec0c048b1f3658cc335b940df4f6d22 ]

tcf_pedit_init() can fail to allocate 'keys' after the idr has been
successfully reserved. When this happens, subsequent attempts to configure
a pedit rule using the same idr value systematically fail with -ENOSPC:

 # tc action add action pedit munge ip ttl set 63 index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action add action pedit munge ip ttl set 63 index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 # tc action add action pedit munge ip ttl set 63 index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 ...

Fix this in the error path of tcf_act_pedit_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().

Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix idr leak in the error path of tcf_act_police_init()

[ Upstream commit 5bf7f8185f7c7112decdfe3d3e5c5d5e67f099a1 ]

tcf_act_police_init() can fail after the idr has been successfully
reserved (e.g., qdisc_get_rtab() may return NULL). When this happens,
subsequent attempts to configure a police rule using the same idr value
systematiclly fail with -ENOSPC:

 # tc action add action police rate 1000 burst 1000 drop index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc action add action police rate 1000 burst 1000 drop index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 # tc action add action police rate 1000 burst 1000 drop index 100
 RTNETLINK answers: No space left on device
 ...

Fix this in the error path of tcf_act_police_init(), calling
tcf_idr_release() in place of tcf_idr_cleanup().

Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix idr leak in the error path of tcf_simp_init()

[ Upstream commit 60e10b3adc3bac0f6a894c28e0eb1f2d13607362 ]

if the kernel fails to duplicate 'sdata', creation of a new action fails
with -ENOMEM. However, subsequent attempts to install the same action
using the same value of 'index' systematically fail with -ENOSPC, and
that value of 'index' will no more be usable by act_simple, until rmmod /
insmod of act_simple.ko is done:

 # tc actions add action simple sdata hello index 100
 # tc actions list action simple

        action order 0: Simple <hello>
         index 100 ref 1 bind 0
 # tc actions flush action simple
 # tc actions add action simple sdata hello index 100
 RTNETLINK answers: Cannot allocate memory
 We have an error talking to the kernel
 # tc actions flush action simple
 # tc actions add action simple sdata hello index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 # tc actions add action simple sdata hello index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel
 ...

Fix this in the error path of tcf_simp_init(), calling tcf_idr_release()
in place of tcf_idr_cleanup().

Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix idr leak on the error path of tcf_bpf_init()

[ Upstream commit bbc09e7842a5023ba5bc0f8d559b9dd464e44006 ]

when the following command sequence is entered

 # tc action add action bpf bytecode '4,40 0 0 12,31 0 1 2048,6 0 0 262144,6 0 0 0' index 100
 RTNETLINK answers: Invalid argument
 We have an error talking to the kernel
 # tc action add action bpf bytecode '4,40 0 0 12,21 0 1 2048,6 0 0 262144,6 0 0 0' index 100
 RTNETLINK answers: No space left on device
 We have an error talking to the kernel

act_bpf correctly refuses to install the first TC rule, because 31 is not
a valid instruction. However, it refuses to install the second TC rule,
even if the BPF code is correct. Furthermore, it's no more possible to
install any other rule having the same value of 'index' until act_bpf
module is unloaded/inserted again. After the idr has been reserved, call
tcf_idr_release() instead of tcf_idr_cleanup(), to fix this issue.

Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR")
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix QP state initialization race

[ Upstream commit caf61b1b8b88ccf1451f7321a176393797e8d292 ]

Once the FW is transitioned to error, FLUSH cqes can be received.
We want the driver to be aware of the fact that QP is already in error.

Without this fix, a user may see false error messages in the dmesg log,
mentioning that a FLUSH cqe was received while QP is not in error state.

Fixes: cecbcddf ("qedr: Add support for QP verbs")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix rc initialization on CNQ allocation failure

[ Upstream commit b15606f47b89b0b09936d7f45b59ba6275527041 ]

Return code wasn't set properly when CNQ allocation failed.
This only affect error message logging, currently user will
receive an error message that says the qedr driver load failed
with rc '0', instead of ENOMEM

Fixes: ec72fce4 ("qedr: Add support for RoCE HW init")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: fix QP's ack timeout configuration

[ Upstream commit c3594f22302cca5e924e47ec1cc8edd265708f41 ]

QPs that were configured with ack timeout value lower than 1
msec will not implement re-transmission timeout.
This means that if a packet / ACK were dropped, the QP
will not retransmit this packet.

This can lead to an application hang.

Fixes: cecbcddf6 ("qedr: Add support for QP verbs")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/ucma: Correct option size check using optlen

[ Upstream commit 5f3e3b85cc0a5eae1c46d72e47d3de7bf208d9e2 ]

The option size check is using optval instead of optlen
causing the set option call to fail. Use the correct
field, optlen, for size check.

Fixes: 6a21dfc0d0db ("RDMA/ucma: Limit possible option size")
Signed-off-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: make scripts/adjust_autoksyms.sh robust against timestamp races

[ Upstream commit 825d487583089f9a33d31650c9c41f6474aab7fc ]

Some filesystems have timestamps with coarse precision that may allow
for a recently built object file to have the same timestamp as the
updated time on one of its dependency files. When that happens, the
object file doesn't get rebuilt as it should.

This is especially the case on filesystems that don't have sub-second
time precision, such as ext3 or Ext4 with 128B inodes.

Let's prevent that by making sure updated dependency files have a newer
timestamp than the first file we created (i.e. autoksyms.h.tmpnew).

Reported-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Thomas Lindroth <thomas.lindroth@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

brcmfmac: Fix check for ISO3166 code

[ Upstream commit 9b9322db5c5a1917a66c71fe47c3848a9a31227e ]

The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.

Fixes: 657308f73e67 ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/cgroup: Fix child event counting bug

[ Upstream commit c917e0f259908e75bd2a65877e25f9d90c22c848 ]

When a perf_event is attached to parent cgroup, it should count events
for all children cgroups:

   parent_group   <---- perf_event
     \
      - child_group  <---- process(es)

However, in our tests, we found this perf_event cannot report reliable
results. Here is an example case:

  # create cgroups
  mkdir -p /sys/fs/cgroup/p/c
  # start perf for parent group
  perf stat -e instructions -G "p"

  # on another console, run test process in child cgroup:
  stressapptest -s 2 -M 1000 & echo $! > /sys/fs/cgroup/p/c/cgroup.procs

  # after the test process is done, stop perf in the first console shows

       <not counted>      instructions              p

The instruction should not be "not counted" as the process runs in the
child cgroup.

We found this is because perf_event->cgrp and cpuctx->cgrp are not
identical, thus perf_event->cgrp are not updated properly.

This patch fixes this by updating perf_cgroup properly for ancestor
cgroup(s).

Reported-by: Ephraim Park <ephiepark@fb.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <jolsa@redhat.com>
Cc: <kernel-team@fb.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20180312165943.1057894-1-songliubraving@fb.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/tegra: Shutdown on driver unbind

[ Upstream commit 192b4af6cd28cdad9b42fd79c21a90a2aeb0bec7 ]

Since commit 846c7dfc1193 ("drm/atomic: Try to preserve the crtc enabled
state in drm_atomic_remove_fb, v2."), removing the last framebuffer will
no longer disable the corresponding pipeline, which causes the KMS core
to complain about leaked connectors on driver unbind.

Fix this by calling drm_atomic_helper_shutdown() on driver unbind, which
will cause all display pipelines to be shut down and therefore drop the
extra references on the connectors.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix array out of bounds reference

[ Upstream commit 4a6d2e525b43eba5870ea7e360f59aa65de00705 ]

When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.

While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.

Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: make sure internal station has a valid id

[ Upstream commit df65c8d1728adee2a52c30287d33da83a8c87480 ]

If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.

Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: clear tx queue id when unreserving aggregation queue

[ Upstream commit 4b387906b1c3692bb790388c335515c0cf098a23 ]

When a queue is reserved for aggregation, the queue id is assigned
to the tid_data. This is fine since iwl_mvm_sta_tx_agg_oper()
takes care of allocating the queue before actual tx starts.
When the reservation is cancelled (e.g. when the AP declined the
aggregation request) the tid_data is not cleared. As a result,
following tx for this tid was trying to use an unallocated queue.

Fix this by setting the txq_id for the tid to invalid when unreserving
the queue.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: Increase session protection time after CS

[ Upstream commit 19125cb0591ae63cd4591e3dfe4c22058e748518 ]

After switching to a new channel, driver schedules session protection
time event in order to hear the beacon on the new channel.
The duration of the protection is two beacon intervals.
However, since we start to switch slightly before beacon with count 1, in
case we don't hear (or AP doesn't transmit) the very first beacon on the
new channel the protection ends without hearing any beacon at all.
At this stage the switch is not complete, the queues are closed and the
interface doesn't have quota yet or TBTT events. As the result, we are
stuck forever waiting for iwl_mvm_post_channel_switch() to be called.

Fix this by increasing the protection time to be 3 beacon intervals and
in addition drop the connection if the time event ends before we got any
beacon.

Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vti6: Fix dev->max_mtu setting

[ Upstream commit f8a554b4aa9686bb2c12f6bae516e58783289a03 ]

We shouldn't allow a tunnel to have IP_MAX_MTU as MTU, because
another IPv6 header is going on top of our packets. Without this
patch, we might end up building packets bigger than IP_MAX_MTU.

Fixes: b96f9afee4eb ("ipv4/6: use core net MTU range checking")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vti4: Don't override MTU passed on link creation via IFLA_MTU

[ Upstream commit 03080e5ec72740c1a62e6730f2a5f3f114f11b19 ]

Don't hardcode a MTU value on vti tunnel initialization,
ip_tunnel_newlink() is able to deal with this already. See also
commit ffc2b6ee4174 ("ip_gre: fix IFLA_MTU ignored on NEWLINK").

Fixes: 1181412c1a67 ("net/ipv4: VTI support new module for ip_vti.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_tunnel: Clamp MTU to bounds on new link

[ Upstream commit 24fc79798b8ddfd46f2dd363a8d29072c083b977 ]

Otherwise, it's possible to specify invalid MTU values directly
on creation of a link (via 'ip link add'). This is already
prevented on subsequent MTU changes by commit b96f9afee4eb
("ipv4/6: use core net MTU range checking").

Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vti4: Don't count header length twice on tunnel setup

[ Upstream commit dd1df24737727e119c263acf1be2a92763938297 ]

This re-introduces the effect of commit a32452366b72 ("vti4:
Don't count header length twice.") which was accidentally
reverted by merge commit f895f0cfbb77 ("Merge branch 'master' of
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec").

The commit message from Steffen Klassert said:

    We currently count the size of LL_MAX_HEADER and struct iphdr
    twice for vti4 devices, this leads to a wrong device mtu.
    The size of LL_MAX_HEADER and struct iphdr is already counted in
    ip_tunnel_bind_dev(), so don't do it again in vti_tunnel_init().

And this is still the case now: ip_tunnel_bind_dev() already
accounts for the header length of the link layer (not
necessarily LL_MAX_HEADER, if the output device is found), plus
one IP header.

For example, with a vti device on top of veth, with MTU of 1500,
the existing implementation would set the initial vti MTU to
1332, accounting once for LL_MAX_HEADER (128, included in
hard_header_len by vti) and twice for the same IP header (once
from hard_header_len, once from ip_tunnel_bind_dev()).

It should instead be 1480, because ip_tunnel_bind_dev() is able
to figure out that the output device is veth, so no additional
link layer header is attached, and will properly count one
single IP header.

The existing issue had the side effect of avoiding PMTUD for
most xfrm policies, by arbitrarily lowering the initial MTU.
However, the only way to get a consistent PMTU value is to let
the xfrm PMTU discovery do its course, and commit d6af1a31cc72
("vti: Add pmtu handling to vti_xmit.") now takes care of local
delivery cases where the application ignores local socket
notifications.

Fixes: b9959fd3b0fa ("vti: switch to new ip tunnel code")
Fixes: f895f0cfbb77 ("Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix skbuff rcsum on packet reroute

[ Upstream commit fc04fdb2c8a894283259f5621d31d75610701091 ]

batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.

Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4c7 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: fix NULL dereference in the error path of tcf_sample_init()

[ Upstream commit 1f110e7cae09e6c6a144616480d1a9dd99c5208a ]

when the following command

 # tc action add action sample rate 100 group 100 index 100

is run for the first time, and psample_group_get(100) fails to create a
new group, tcf_sample_cleanup() calls psample_group_put(NULL), thus
causing the following error:

 BUG: unable to handle kernel NULL pointer dereference at 000000000000001c
 IP: psample_group_put+0x15/0x71 [psample]
 PGD 8000000075775067 P4D 8000000075775067 PUD 7453c067 PMD 0
 Oops: 0002 [#1] SMP PTI
 Modules linked in: act_sample(E) psample ip6table_filter ip6_tables iptable_filter binfmt_misc ext4 snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hda_core mbcache jbd2 crct10dif_pclmul snd_hwdep crc32_pclmul snd_seq ghash_clmulni_intel pcbc snd_seq_device snd_pcm aesni_intel crypto_simd snd_timer glue_helper snd cryptd joydev pcspkr i2c_piix4 soundcore virtio_balloon nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm virtio_net ata_piix virtio_console virtio_blk libata serio_raw crc32c_intel virtio_pci i2c_core virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: act_tunnel_key]
 CPU: 2 PID: 5740 Comm: tc Tainted: G            E    4.16.0-rc4.act_vlan.orig+ #403
 Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
 RIP: 0010:psample_group_put+0x15/0x71 [psample]
 RSP: 0018:ffffb8a80032f7d0 EFLAGS: 00010246
 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000024
 RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffffffffc06d93c0
 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000044
 R10: 00000000bd003000 R11: ffff979fba04aa59 R12: 0000000000000000
 R13: 0000000000000000 R14: 0000000000000000 R15: ffff979fbba3f22c
 FS:  00007f7638112740(0000) GS:ffff979fbfd00000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 000000000000001c CR3: 00000000734ea001 CR4: 00000000001606e0
 Call Trace:
  __tcf_idr_release+0x79/0xf0
  tcf_sample_init+0x125/0x1d0 [act_sample]
  tcf_action_init_1+0x2cc/0x430
  tcf_action_init+0xd3/0x1b0
  tc_ctl_action+0x18b/0x240
  rtnetlink_rcv_msg+0x29c/0x310
  ? _cond_resched+0x15/0x30
  ? __kmalloc_node_track_caller+0x1b9/0x270
  ? rtnl_calcit.isra.28+0x100/0x100
  netlink_rcv_skb+0xd2/0x110
  netlink_unicast+0x17c/0x230
  netlink_sendmsg+0x2cd/0x3c0
  sock_sendmsg+0x30/0x40
  ___sys_sendmsg+0x27a/0x290
  ? filemap_map_pages+0x34a/0x3a0
  ? __handle_mm_fault+0xbfd/0xe20
  __sys_sendmsg+0x51/0x90
  do_syscall_64+0x6e/0x1a0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2
 RIP: 0033:0x7f7637523ba0
 RSP: 002b:00007fff0473ef58 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
 RAX: ffffffffffffffda RBX: 00007fff0473f080 RCX: 00007f7637523ba0
 RDX: 0000000000000000 RSI: 00007fff0473efd0 RDI: 0000000000000003
 RBP: 000000005aaaac80 R08: 0000000000000002 R09: 0000000000000000
 R10: 00007fff0473e9e0 R11: 0000000000000246 R12: 0000000000000000
 R13: 00007fff0473f094 R14: 0000000000000001 R15: 0000000000669f60
 Code: be 02 00 00 00 48 89 df e8 a9 fe ff ff e9 7c ff ff ff 0f 1f 40 00 0f 1f 44 00 00 53 48 89 fb 48 c7 c7 c0 93 6d c0 e8 db 20 8c ef <83> 6b 1c 01 74 10 48 c7 c7 c0 93 6d c0 ff 14 25 e8 83 83 b0 5b
 RIP: psample_group_put+0x15/0x71 [psample] RSP: ffffb8a80032f7d0
 CR2: 000000000000001c

Fix it in tcf_sample_cleanup(), ensuring that calls to psample_group_put(p)
are done only when p is not NULL.

Fixes: cadb9c9fdbc6 ("net/sched: act_sample: Fix error path in init")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix header size check in batadv_dbg_arp()

[ Upstream commit 6f27d2c2a8c236d296201c19abb8533ec20d212b ]

Checking for 0 is insufficient: when an SKB without a batadv header, but
with a VLAN header is received, hdr_size will be 4, making the following
code interpret the Ethernet header as a batadv header.

Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vlan: Fix out of order vlan headers with reorder header off

[ Upstream commit cbe7128c4b92e2004984f477fd38dfa81662f02e ]

With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().

This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.

This patch fixes the behaviour by inserting the inner tag at the right
position.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off

[ Upstream commit 4bbb3e0e8239f9079bf1fe20b3c0cb598714ae61 ]

When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().

The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.

The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.

In rx path single tag case, it works as follows:

- Before skb_reorder_vlan_header()

 mac_header                                data
   v                                        v
   +-------------------+-------------+------+----
   |        ETH        |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TYPE |
   +-------------------+-------------+------+----
   <-------- mac_len --------->
                       <------------->
                        to be removed

- After skb_reorder_vlan_header()

            mac_header                     data
                 v                          v
                 +-------------------+------+----
                 |        ETH        | ETH  |
                 |       ADDRS       | TYPE |
                 +-------------------+------+----
                 <-------- mac_len --------->

This is ok, but in rx double tag case, it corrupts packets:

- Before skb_reorder_vlan_header()

 mac_header                                              data
   v                                                      v
   +-------------------+-------------+-------------+------+----
   |        ETH        |    VLAN     |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TPID | TCI  | TYPE |
   +-------------------+-------------+-------------+------+----
   <--------------- mac_len ---------------->
                                     <------------->
                                    should be removed
                       <--------------------------->
                         actually will be removed

- After skb_reorder_vlan_header()

            mac_header                                   data
                 v                                        v
                               +-------------------+------+----
                               |        ETH        | ETH  |
                               |       ADDRS       | TYPE |
                               +-------------------+------+----
                 <--------------- mac_len ---------------->

So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.

skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.

Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff11170 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix error checking for multi/broadcast sta

[ Upstream commit 75fd4fec3e4c43b131c7c4958adb3ab9f1665513 ]

The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.

Found by smatch:

.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'

Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: Correctly set IGTK for AP

[ Upstream commit e829b17caf96c2da34620e335fb777592990906c ]

Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.

Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: set the correct tid when we flush the MCAST sta

[ Upstream commit 334167decf98f01a66c91ea84180c278bc4ad290 ]

The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.

The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.

To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.

Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: fix rcu_read_unlock usage in xfrm_local_error

[ Upstream commit 46c0ef6e1eb95f619d9f62da4332749153db92f7 ]

In the xfrm_local_error, rcu_read_unlock should be called when afinfo
is not NULL. because xfrm_state_get_afinfo calls rcu_read_unlock
if afinfo is NULL.

Fixes: af5d27c4e12b ("xfrm: remove xfrm_state_put_afinfo")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/nouveau/bl: fix backlight regression

[ Upstream commit 9e75dc61eaa9acd1bff83c3b814ac2af6dc1f64c ]

Fixes: 3c66c87dc9 ("drm/nouveau/disp: remove hw-specific customisation
of output paths")
Suggested-by: Ben Skeggs <skeggsb@redhat.com>
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/imx: move arming of the vblank event to atomic_flush

[ Upstream commit 6a055b92de15af987b4027826d43aa103c65a3c4 ]

Right now the vblank event completion is racing with the atomic update,
which is especially bad when the PRE is in use, as one of the hardware
issue workaround might extend the atomic commit for quite some time.

If the vblank IRQ happens to trigger during that time, we will prematurely
signal the atomic commit completion to userspace, which causes tearing
when userspace re-uses a framebuffer we haven't managed to flip away from
yet.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gpu: ipu-v3: prg: avoid possible array underflow

[ Upstream commit 746d024c3211813946b319411aeb2b47767f8fb0 ]

gcc-8 reports that we access an array with a negative index
in an error case:

drivers/gpu/ipu-v3/ipu-prg.c: In function 'ipu_prg_channel_disable':
drivers/gpu/ipu-v3/ipu-prg.c:252:43: error: array subscript -22 is below array bounds of 'struct ipu_prg_channel[3]' [-Werror=array-bounds]

This moves the range check in front of the first time that
variable gets used.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm/arm64: vgic: Add missing irq_lock to vgic_mmio_read_pending

[ Upstream commit 62b06f8f429cd233e4e2e7bbd21081ad60c9018f ]

Our irq_is_pending() helper function accesses multiple members of the
vgic_irq struct, so we need to hold the lock when calling it.
Add that requirement as a comment to the definition and take the lock
around the call in vgic_mmio_read_pending(), where we were missing it
before.

Fixes: 96b298000db4 ("KVM: arm/arm64: vgic-new: Add PENDING registers handlers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sunvnet: does not support GSO for sctp

[ Upstream commit cf55612a945039476abfd73e39064b2e721c3272 ]

The NETIF_F_GSO_SOFTWARE implies support for GSO on SCTP, but the
sunvnet driver does not support GSO for sctp.  Here we remove the
NETIF_F_GSO_SOFTWARE feature flag and only report NETIF_F_ALL_TSO
instead.

Signed-off-by: Cathy Zhou <Cathy.Zhou@Oracle.COM>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu

[ Upstream commit d52e5a7e7ca49457dd31fc8b42fb7c0d58a31221 ]

Prior to the rework of PMTU information storage in commit
2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.

Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.

This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().

One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.

Fixes: 2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

workqueue: use put_device() instead of kfree()

[ Upstream commit 537f4146c53c95aac977852b371bafb9c6755ee1 ]

Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized in this function instead.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Check valid VNIC ID in bnxt_hwrm_vnic_set_tpa().

[ Upstream commit 3c4fe80b32c685bdc02b280814d0cfe80d441c72 ]

During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID.  This may cause a
warning in firmware logs.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: m_can: select pinctrl state in each suspend/resume function

[ Upstream commit c9b3bce18da4a0aebc27853052dea39aa64b7d75 ]

Make sure to apply the correct pin state in suspend/resume callbacks.
Putting pins in sleep state saves power.

Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: m_can: change comparison to bitshift when dealing with a mask

[ Upstream commit b7db978ac283b237835129ac87f26cbac94d04e7 ]

Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ebtables: fix erroneous reject of last rule

[ Upstream commit 932909d9b28d27e807ff8eecb68c7748f6701628 ]

The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.

Fixes: b71812168571fa ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: mv_xor_v2: Fix clock resource by adding a register clock

[ Upstream commit 3cd2c313f1d618f92d1294addc6c685c17065761 ]

On the CP110 components which are present on the Armada 7K/8K SoC we need
to explicitly enable the clock for the registers. However it is not
needed for the AP8xx component, that's why this clock is optional.

With this patch both clock have now a name, but in order to be backward
compatible, the name of the first clock is not used. It allows to still
use this clock with a device tree using the old binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/test_kmod.c: fix limit check on number of test devices created

[ Upstream commit ac68b1b3b9c73e652dc7ce0585672e23c5a2dca4 ]

As reported by Dan the parentheses is in the wrong place, and since
unlikely() call returns either 0 or 1 it's never less than zero.  The
second issue is that signed integer overflows like "INT_MAX + 1" are
undefined behavior.

Since num_test_devs represents the number of devices, we want to stop
prior to hitting the max, and not rely on the wrap arround at all.  So
just cap at num_test_devs + 1, prior to assigning a new device.

Link: http://lkml.kernel.org/r/20180224030046.24238-1-mcgrof@kernel.org
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/vm/run_vmtests: adjust hugetlb size according to nr_cpus

[ Upstream commit 0627be7d3c871035364923559543c9b2ff5357f2 ]

Fix userfaultfd_hugetlb on hosts which have more than 64 cpus.

  ---------------------------
  running userfaultfd_hugetlb
  ---------------------------
  invalid MiB
  Usage: <MiB> <bounces>
  [FAIL]

Via userfaultfd.c we can know, hugetlb_size needs to meet hugetlb_size
>= nr_cpus * hugepage_size.  hugepage_size is often 2M, so when host
cpus > 64, it requires more than 128M.

[zhijianx.li@intel.com: update changelog/comments and variable name]
Link: http://lkml.kernel.org/r/20180302024356.83359-1-zhijianx.li@intel.com
Link: http://lkml.kernel.org/r/20180303125027.81638-1-zhijianx.li@intel.com
Link: http://lkml.kernel.org/r/20180302024356.83359-1-zhijianx.li@intel.com
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: SeongJae Park <sj38.park@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Relax ARM_SMCCC_ARCH_WORKAROUND_1 discovery

[ Upstream commit e21da1c992007594d391e7b301779cf30f438691 ]

A recent update to the ARM SMCCC ARCH_WORKAROUND_1 specification
allows firmware to return a non zero, positive value to describe
that although the mitigation is implemented at the higher exception
level, the CPU on which the call is made is not affected.

Let's relax the check on the return value from ARCH_WORKAROUND_1
so that we only error out if the returned value is negative.

Fixes: b092201e0020 ("arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: davinci: fix the GPIO lookup for omapl138-hawk

[ Upstream commit c4dc56be7e26040bfc60ce73425353516a356955 ]

The GPIO chip is called davinci_gpio.0 in legacy mode. Fix it, so that
mmc can correctly lookup the wp and cp gpios.

Note that it is the gpio-davinci driver that sets the gpiochip label to
davinci_gpio.0.

Fixes: c69f43fb4f26 ("ARM: davinci: hawk: use gpio descriptor for mmc pins")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a note on where the chip label is set]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: fix locking during VF setup

[ Upstream commit b0dee7910317f41f398838992516af6a3b981d86 ]

The dev_uc/mc_sync calls need to have the device address list
locked. This was spotted by running with lockdep enabled.

Fixes: bee9d41b37ea ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: fix locking for rx_mode

[ Upstream commit 35a57b7fef136fa3d5b735ba773f191b95110fa0 ]

The rx_mode operation handler is different than other callbacks
in that is not always called with rtnl held. Therefore use
RCU to ensure that references are valid.

Fixes: bee9d41b37ea ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: fix filter flags

[ Upstream commit de3d50aadd40bf68614db9fd157b275ce9c2d467 ]

The recent change to not always enable all multicast and broadcast
was broken; meant to set filter, not change flags.

Fixes: 009f766ca238 ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: xenbus: use put_device() instead of kfree()

[ Upstream commit 351b2bccede1cb673ec7957b35ea997ea24c8884 ]

Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-blkfront: move negotiate_mq to cover all cases of new VBDs

[ Upstream commit 7ed8ce1c5fc7cf25b3602c73bef897a3466a6645 ]

negotiate_mq should happen in all cases of a new VBD being discovered by
xen-blkfront, whether called through _probe() or a hot-attached new VBD
from dom-0 via xenstore. Otherwise, hot-attached new VBDs are left
configured without multi-queue.

Signed-off-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4: do not set needs_free_netdev for mgmt dev's

[ Upstream commit b06ef18a4c255609388ed6e068a1c69c797545e0 ]

Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.

Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/core: Fix possible crash to access NULL netdev

[ Upstream commit bb7f8f199c354c4cf155b1d6d55f86eaaed7fa5a ]

resolved_dev returned might be NULL as ifindex is transient number.
Ignoring NULL check of resolved_dev might crash the kernel.
Therefore perform NULL check before accessing resolved_dev.

Additionally rdma_resolve_ip_route() invokes addr_resolve() which
performs check and address translation for loopback ifindex.
Therefore, checking it again in rdma_resolve_ip_route() is not helpful.
Therefore, the code is simplified to avoid IFF_LOOPBACK check.

Fixes: 200298326b27 ("IB/core: Validate route when we init ah")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: smsc911x: Fix unload crash when link is up

[ Upstream commit e06513d78d54e6c7026c9043a39e2c01ee25bdbe ]

The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:

Call trace:
  phy_detach+0x94/0x150
  phy_disconnect+0x40/0x50
  smsc911x_stop+0x104/0x128 [smsc911x]
  __dev_close_many+0xb4/0x138
  dev_close_many+0xbc/0x190
  rollback_registered_many+0x140/0x460
  rollback_registered+0x68/0xb0
  unregister_netdevice_queue+0x100/0x118
  unregister_netdev+0x28/0x38
  smsc911x_drv_remove+0x58/0x130 [smsc911x]
  platform_drv_remove+0x30/0x50
  device_release_driver_internal+0x15c/0x1f8
  driver_detach+0x54/0x98
  bus_remove_driver+0x64/0xe8
  driver_unregister+0x34/0x60
  platform_driver_unregister+0x20/0x30
  smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
  SyS_delete_module+0x1e8/0x238
  __sys_trace_return+0x0/0x4

This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()

To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.

Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qcom/emac: Use proper free methods during TX

[ Upstream commit cc5db3150e87fe7f7e947bf333b6c1c97f848ecb ]

This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.

Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Free RoCE ILT Memory on rmmod qedr

[ Upstream commit 9de506a547c0d172d13a91d69b1a399e6a2c0efa ]

Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).

An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.

The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.

In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.

Fixes: dbb799c39717 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fsl/fman: avoid sleeping in atomic context while adding an address

[ Upstream commit 803fafbe0cd522fa6b9e41ca3b96cfb2e2a2222d ]

__dev_mc_add grabs an adress spinlock so use
atomic context in kmalloc.

/ # ifconfig eth0 inet 192.168.0.111
[   89.331622] BUG: sleeping function called from invalid context at mm/slab.h:420
[   89.339002] in_atomic(): 1, irqs_disabled(): 0, pid: 1035, name: ifconfig
[   89.345799] 2 locks held by ifconfig/1035:
[   89.349908]  #0:  (rtnl_mutex){+.+.}, at: [<(ptrval)>] devinet_ioctl+0xc0/0x8a0
[   89.357258]  #1:  (_xmit_ETHER){+...}, at: [<(ptrval)>] __dev_mc_add+0x28/0x80
[   89.364520] CPU: 1 PID: 1035 Comm: ifconfig Not tainted 4.16.0-rc3-dirty #8
[   89.371464] Call Trace:
[   89.373908] [e959db60] [c066f948] dump_stack+0xa4/0xfc (unreliable)
[   89.380177] [e959db80] [c00671d8] ___might_sleep+0x248/0x280
[   89.385833] [e959dba0] [c01aec34] kmem_cache_alloc_trace+0x174/0x320
[   89.392179] [e959dbd0] [c04ab920] dtsec_add_hash_mac_address+0x130/0x240
[   89.398874] [e959dc00] [c04a9d74] set_multi+0x174/0x1b0
[   89.404093] [e959dc30] [c04afb68] dpaa_set_rx_mode+0x68/0xe0
[   89.409745] [e959dc40] [c057baf8] __dev_mc_add+0x58/0x80
[   89.415052] [e959dc60] [c060fd64] igmp_group_added+0x164/0x190
[   89.420878] [e959dca0] [c060ffa8] ip_mc_inc_group+0x218/0x460
[   89.426617] [e959dce0] [c06120fc] ip_mc_up+0x3c/0x190
[   89.431662] [e959dd10] [c0607270] inetdev_event+0x250/0x620
[   89.437227] [e959dd50] [c005f190] notifier_call_chain+0x80/0xf0
[   89.443138] [e959dd80] [c0573a74] __dev_notify_flags+0x54/0xf0
[   89.448964] [e959dda0] [c05743f8] dev_change_flags+0x48/0x60
[   89.454615] [e959ddc0] [c0606744] devinet_ioctl+0x544/0x8a0
[   89.460180] [e959de10] [c060987c] inet_ioctl+0x9c/0x1f0
[   89.465400] [e959de80] [c05479a8] sock_ioctl+0x168/0x460
[   89.470708] [e959ded0] [c01cf3ec] do_vfs_ioctl+0xac/0x8c0
[   89.476099] [e959df20] [c01cfc40] SyS_ioctl+0x40/0xc0
[   89.481147] [e959df40] [c0011318] ret_from_syscall+0x0/0x3c
[   89.486715] --- interrupt: c01 at 0x1006943c
[   89.486715]     LR = 0x100c45ec

Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: Fixing arbitrary kernel leak in case FBIOGETCMAP_SPARC in sbusfb_ioctl_helper().

[ Upstream commit 250c6c49e3b68756b14983c076183568636e2bde ]

Fixing arbitrary kernel leak in case FBIOGETCMAP_SPARC in
sbusfb_ioctl_helper().

'index' is defined as an int in sbusfb_ioctl_helper().
We retrieve this from the user:
if (get_user(index, &c->index) ||
    __get_user(count, &c->count) ||
    __get_user(ured, &c->red) ||
    __get_user(ugreen, &c->green) ||
    __get_user(ublue, &c->blue))
       return -EFAULT;

and then we use 'index' in the following way:
red = cmap->red[index + i] >> 8;
green = cmap->green[index + i] >> 8;
blue = cmap->blue[index + i] >> 8;

This is a classic information leak vulnerability. 'index' should be
an unsigned int, given its usage above.

This patch is straight-forward; it changes 'index' to unsigned int
in two switch-cases: FBIOGETCMAP_SPARC && FBIOPUTCMAP_SPARC.

This patch fixes CVE-2018-6412.

Signed-off-by: Peter Malone <peter.malone@gmail.com>
Acked-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix an error code in __mlx5_ib_modify_qp()

[ Upstream commit 5d414b178e950ce9685c253994cc730893d5d887 ]

"err" is either zero or possibly uninitialized here.  It should be
-EINVAL.

Fixes: 427c1e7bcd7e ("{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Include GID type when deleting GIDs from HW table under RoCE

[ Upstream commit a18177925c252da7801149abe217c05b80884798 ]

The commit cited below added a gid_type field (RoCEv1 or RoCEv2)
to GID properties.

When adding GIDs, this gid_type field was copied over to the
hardware gid table. However, when deleting GIDs, the gid_type field
was not copied over to the hardware gid table.

As a result, when running RoCEv2, all RoCEv2 gids in the
hardware gid table were set to type RoCEv1 when any gid was deleted.

This problem would persist until the next gid was added (which would again
restore the gid_type field for all the gids in the hardware gid table).

Fix this by copying over the gid_type field to the hardware gid table
when deleting gids, so that the gid_type of all remaining gids is
preserved when a gid is deleted.

Fixes: b699a859d17b ("IB/mlx4: Add gid_type to GID properties")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix corruption of RoCEv2 IPv4 GIDs

[ Upstream commit 0077416a3d529baccbe07ab3242e8db541cfadf6 ]

When using IPv4 addresses in RoCEv2, the GID format for the mapped
IPv4 address should be: ::ffff:<4-byte IPv4 address>.

In the cited commit, IPv4 mapped IPV6 addresses had the 3 upper dwords
zeroed out by memset, which resulted in deleting the ffff field.

However, since procedure ipv6_addr_v4mapped() already verifies that the
gid has format ::ffff:<ipv4 address>, no change is needed for the gid,
and the memset can simply be removed.

Fixes: 7e57b85c444c ("IB/mlx4: Add support for setting RoCEv2 gids in hardware")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix iWARP write and send with immediate

[ Upstream commit 551e1c67b4207455375a2e7a285dea1c7e8fc361 ]

iWARP does not support RDMA WRITE or SEND with immediate data.
Driver should check this before submitting to FW and return an
immediate error

Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix kernel panic when running fio over NFSoRDMA

[ Upstream commit e3fd112cbf21d049faf64ba1471d72b93c22109a ]

Race in qedr_poll_cq, lastest_cqe wasn't protected by lock,
leading to a case where two context's accessing poll_cq at
the same time lead to one of them having a pointer to an old
latest_cqe and reading an invalid cqe element

Signed-off-by: Amit Radzi <Amit.Radzi@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ia64/err-inject: Use get_user_pages_fast()

[ Upstream commit 69c907022a7d9325cdc5c9dd064571e445df9a47 ]

At the point of sysfs callback, the call to gup is
done without mmap_sem (or any lock for that matter).
This is racy. As such, use the get_user_pages_fast()
alternative and safely avoid taking the lock, if possible.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>