Masahiro Yamada [Tue, 21 Jul 2015 05:04:23 +0000 (14:04 +0900)]
ARM: dts: UniPhier: add I2C ch4 device node for PH1-sLD3
This I2C device is used SoC-internally for controlling the DMD core.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 21 Jul 2015 05:04:22 +0000 (14:04 +0900)]
ARM: UniPhier: add PH1-sLD3 SoC support
The init code for UMC (Unified Memory Controller) and PLL has not
been mainlined yet, but U-boot proper should work.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 21 Jul 2015 05:04:21 +0000 (14:04 +0900)]
ARM: UniPhier: update CONFIG_BOOTARGS
Both "earlyprintk" and "loglevel=8" should be useful for the
development.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 21 Jul 2015 05:04:20 +0000 (14:04 +0900)]
ARM: UniPhier: disable CONFIG_FIT
To use FIT boot, we have to describe Image Tree Source in addition.
So, it is not intended for beginners. Disable it by default.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 21 Jul 2015 05:04:19 +0000 (14:04 +0900)]
ARM: UniPhier: add environment variable for TFTP boot
The command "run tftpboot" downloads some files onto the RAM
via TFTP and boots the kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 21 Jul 2015 05:04:18 +0000 (14:04 +0900)]
ARM: UniPhier: add environment sets for non-FIT Linux boot
Currently, the environment variables "norboot" and "nandboot" only
work with CONFIG_FIT, but we do not want to depend on CONFIG_FIT to
boot the kernel.
This commit adds environments useful for booting Linux with separate
uImage + ramdisk + DTB.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 13 Jul 2015 01:35:34 +0000 (10:35 +0900)]
ARM: dts: UniPhier: add device-specific compatible string for EEPROM
For the record, describe exactly which device of which vendor
is used on this board.
I2C EEPROM is bound by the generic compatible string, "i2c-eeprom",
so this commit has no impact on the functionality.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Mon, 20 Jul 2015 21:12:52 +0000 (17:12 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq
Zhichun Hua [Mon, 29 Jun 2015 07:50:42 +0000 (15:50 +0800)]
armv8/fsl-lsch3: Fix TCR_EL3 for the final MMU setup.
When final MMU table is setup in DDR, TCR attributes must match
those of the memroy for cacheability and shareability.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Zhichun Hua [Mon, 29 Jun 2015 07:49:37 +0000 (15:49 +0800)]
armv8: Fix TCR macros for shareability attribute
For ARMv8, outer shareable is 0b10, inner shareable is 0b11 at bit
position [13:12] of TCR_ELx register.
Signed-off-by: Zhichun Hua <zhichun.hua@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Haikun.Wang@freescale.com [Fri, 3 Jul 2015 08:51:36 +0000 (16:51 +0800)]
armv8/ls2085a/defconfig: Enable FSL_DSPI, OF_CONTROL and DM support
Freescale DSPI driver has been converted to Driver Model.
The new driver depends on OF_CONTROL, DM, DM_SPI.
This patch enable FSL_DSPI and its dependence configure options.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 3 Jul 2015 08:51:35 +0000 (16:51 +0800)]
armv8/ls2085ardb: Enable DSPI flash support for LS2085ARDB
Enable DSPI flash related configurations for LS2085ARDB.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 3 Jul 2015 08:51:34 +0000 (16:51 +0800)]
armv8/ls2085aqds: Enable DSPI flash support for LS2085AQDS
Enable DSPI flash related configurations.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun.Wang@freescale.com [Fri, 26 Jun 2015 11:58:24 +0000 (19:58 +0800)]
armv8/ls2085ardb: DSPI pin muxing configure through QIXIS CPLD
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS CPLD to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 26 Jun 2015 11:58:12 +0000 (19:58 +0800)]
armv8/ls2085aqds: DSPI pin muxing configure through QIXIS
DSPI has pin muxing with SDHC and other IPs, this patch check the
value of RCW SPI_PCS_BASE and SPI_BASE_BASE fields, it also check
the "hwconfig" variable. If those pins are configured to DSPI and
"hwconfig" enable DSPI, set the BRDCFG5 of QIXIS FPGA to configure
the routing to on-board SPI memory. Otherwise will configure to SDHC.
DSPI is enabled in "hwconfig" by appending "dspi", eg.
setenv hwconfig "$hwconfig;dspi"
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 26 Jun 2015 11:56:11 +0000 (19:56 +0800)]
armv8/ls2085a: Enable DSPI get input clk form 'mxc_get_clock'
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 26 Jun 2015 11:48:58 +0000 (19:48 +0800)]
arm/dts/ls2085a: Add dts files for LS2085AQDS and LS2085ARDB
Add dts source files for LS2085AQDS and LS2085ARDB boards.
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 26 Jun 2015 11:48:45 +0000 (19:48 +0800)]
arm/dts/ls2085a: Add DSPI dts node
Add DSPI controller dts node in fsl-ls2085a.dtsi
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Haikun Wang [Fri, 26 Jun 2015 11:48:36 +0000 (19:48 +0800)]
arm/dts/ls2085a: Bring in ls2085a dts files from linux kernel
Bring in required device tree files for ls2085a from Linux. These are
initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Tue, 9 Jun 2015 08:07:49 +0000 (16:07 +0800)]
arm/ls102xa: Add little-endian mode support for audio IPs
As SCFG_ENDIANCR register is added to choose little-endian or big-endian
for audio IPs on Rev2.0 silion, little-endian mode is selected.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Wang Dongsheng [Thu, 4 Jun 2015 04:01:09 +0000 (12:01 +0800)]
arm/ls102xa: Add PSCI support for ls102xa
Base on PSCI services, implement CPU_ON/CPU_OFF for ls102xa platform.
Tested on LS1021AQDS, LS1021ATWR.
Test CPU hotplug times: 60K
Test kernel boot times: 1.2K
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Acked-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Wang Dongsheng [Thu, 4 Jun 2015 04:01:08 +0000 (12:01 +0800)]
ARMv7: Factor out reusable timer_wait from sunxi/psci_sun7i.S
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alison Wang [Mon, 11 May 2015 07:39:47 +0000 (15:39 +0800)]
arm: ls1021a: Remove the inappropriate use of the function 'sprintf'
As the function 'sprintf' does not check buffer boundaries but outputs
to the buffer 'enet' of fixed size (16), this patch removes the function
'sprintf', and uses 'strcpy' instead. It will assign the character
arrays 'enet' and 'phy' the corresponding character strings.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Wed, 1 Jul 2015 10:58:22 +0000 (16:28 +0530)]
board/ls2085a: Increase kernel_size value in env variable
Linux itb image size has been increased from 30MB.
So updating kernel_size to 40MB in env variable.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Sun, 28 Jun 2015 05:33:59 +0000 (11:03 +0530)]
board/ls2085rdb: Export functions for standalone AQ FW load apps
Export functions required by Aquntia PHY firmware load application.
functions are memset, strcpy, mdelay, mdio_get_current_dev,
phy_find_by_mask, mdio_phydev_for_ethname and miiphy_set_current_dev
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:59:08 +0000 (11:29 +0530)]
driver/ldpaa_eth:Avoid infinite loop in ldpaa_eth_rx
Change infinite loop mechanism to timer based polling for QBMAN release in
ldpaa_eth_rx.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:59:07 +0000 (11:29 +0530)]
driver/ldpaa_eth: Avoid TX conf frames
Polling of TX conf frames is not a mandatory option.
Packets can be transferred via WRIOP without TX conf frame.
Configure ldpaa_eth driver to use TX path without confirmation frame
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:59:06 +0000 (11:29 +0530)]
driver/ldpaa_eth: Add timeout handling DQRR entry read
Volatile command does not return frame immidiately, need to wait till a frame
is available in DQRR. Ideally it should be a blocking call.
Add timeout handling for DQRR frame instead of retry counter.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:59:05 +0000 (11:29 +0530)]
driver/ldpaa_eth: Retry enqueue if portal was busy
Do not immediately return if the enqueue function returns -EBUSY; re-try
mulitple times.
if timeout occures, release the buffer.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 2 Jul 2015 05:59:04 +0000 (11:29 +0530)]
armv8/fsl-lsch3: device tree fixups for PCI stream IDs
This patch adds the infrastructure to update device
tree nodes to convey SMMU stream IDs in the device
tree. Fixups are implemented for PCI controllers
initially.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 2 Jul 2015 05:59:03 +0000 (11:29 +0530)]
drivers/fsl-mc: dynamically create ICID pool in DPC
delete any existing ICID pools in the DPC and create
a new one based on the stream ID partitioning for
the SoC
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 2 Jul 2015 05:59:02 +0000 (11:29 +0530)]
armv8/fsl-lsch3: partition stream IDs
Stream IDs on ls2085a devices are not hardwired and are
programmed by sw. There are a limited number of stream IDs
available, and the partitioning of them is scenario dependent.
This header defines the partitioning between legacy, PCI,
and DPAA2 devices.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:59:01 +0000 (11:29 +0530)]
drivers: fsl-mc: Return error for major version mismatch
Management complex major version should match to the firmware present in flash.
Return error during mismatch of major version.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:59:00 +0000 (11:29 +0530)]
drivers: fsl-mc: Update qbman driver
Update qbman driver
- As per latest available qbman driver
- Use of atomic APIs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Geoff Thorpe <Geoff.Thorpe@freescale.com>
CC: Haiying Wang <Haiying.Wang@freescale.com>
CC: Roy Pledge <Roy.Pledge@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:58:59 +0000 (11:28 +0530)]
drivers: fsl-mc: Update flibs to mc-0.6.0.1
Update flibs changes to mc-0.6.0.1 for dpmang, dprc, dpni and dpio objects
Also rename qbman_portal_ce/ci_paddr to qbman_portal_ce/ci_offset in
dpio_attr. These are now offsets from the SoC QBMan portals base.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
J. German Rivera [Thu, 2 Jul 2015 05:58:58 +0000 (11:28 +0530)]
drivers/fsl-mc: Autoload AOIP image from NOR flash
Load AIOP image from NOR flash into DDR so that the MC firmware
the MC fw can start it at boot time
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 2 Jul 2015 05:58:57 +0000 (11:28 +0530)]
driver/ldpaa_eth:Flush buffer before seeding BMAN after TX_conf
Flush buffer before releasing to BMan after TX_conf to ensure, the core does
not have any cachelines that the WRIOP will DMA to.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
J. German Rivera [Thu, 2 Jul 2015 05:58:56 +0000 (11:28 +0530)]
drivers/fsl-mc: Make MC boot error messages more readable
Make it easier for the user to notice when the MC firmware
had problems booting.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Stuart Yoder [Thu, 28 May 2015 09:24:15 +0000 (14:54 +0530)]
armv8/ls2085a: enable debug server
Signed-off-by: Stuart Yoder <stuart.yoder at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Tue, 2 Jun 2015 05:25:52 +0000 (10:55 +0530)]
armv8/fsl-lsch3: Support 256M mem split for MC & dbg-srvr
The agreed split of the top of memory is 256M for debug server and 256M
for MC. This patch implements the split.
In addition, the MC mem must be 512MB aligned, so the amount of memory
to hide must be 512MB to achieve that alignment.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:13 +0000 (14:54 +0530)]
arm/errata: Update required bits for A57 cores erratas
This patch updates the setting of required bits for A57 cores erratas
- 828024 and 826974
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Dai Haruki <dai.haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:12 +0000 (14:54 +0530)]
driver/fsl_debug_server: Fix the DDR hide logic for LS2085a
This patch fixes the DDR hide logic for LS2085a, correcting the way
the Debug Server FW and MC FW images are placed on the top of system
DDR and how the rest of the system DDR space is made visibile to Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:24:11 +0000 (14:54 +0530)]
armv8/ls2085a: Update SoC README for DDR layout
Update SoC README to provide details of
- Memory regions
- Memory used by MC and Debug server
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:10 +0000 (14:54 +0530)]
armv8/ls2085a: Expose all DDR region(s) to Linux
This patch allows u-boot to expose the complete DDR region(s) to Linux
(after subtracting the memory hidden via MEM_TOP_HIDE mechanism).
This allows the u-boot to support the 48-bit VA support provided by
ARM64 Linux in flavors 3.18 and above, by passing the appropriate
'memory' DTS nodes.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Thu, 28 May 2015 09:24:09 +0000 (14:54 +0530)]
armv8/ls2085ardb: Fix SPD address error on early boards
Board rev C and earlier has duplicated SPD address on 2nd DDR
controller slots. It is fixed on rev D and later. SPD addresses
need to be updated accordingly.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
York Sun [Thu, 28 May 2015 09:24:08 +0000 (14:54 +0530)]
driver/ddr/fsl: Add a hook to update SPD address
In case SPD address changes between board revisions, updating SPD
address can be called from board file.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:24:07 +0000 (14:54 +0530)]
armv8/ls2085a: Avoid hard-coding for board name print
LS2085A supports 6 personalities i.e. LS2045AE, LS2045A, LS2080AE,
LS2080A, LS2085AE and LS2085A personlities.
Instead of hard-coding, board name should change as per selected
personality.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:24:06 +0000 (14:54 +0530)]
armv8/fsl-ch3: Add support to print SoC personality
This patch adds support to print out the SoC personality.
Freescale LS20xx SoCs (compliant to Chassis-3 specifications) can
have 6 personalities: LS2045AE, LS2045A, LS2080AE, LS2080A,
LS2085AE and LS2085A
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
York Sun [Thu, 28 May 2015 09:24:05 +0000 (14:54 +0530)]
armv8/fsl-lsch3: Fix DDR speed message
DDR speed should be in MT/s, not MHz.
Signed-off-by: York Sun <yorksun at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:24:04 +0000 (14:54 +0530)]
armv8/ls2085RDB: Update board version print logic
As per updated board document, no need to substract 1 from arch[BRD]
bit field. Default value + 'A' represents the board revision.
So update board version print logic to reflect the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Jaiprakash Singh [Thu, 28 May 2015 09:24:03 +0000 (14:54 +0530)]
board/fsl/common: Fix eeprom system version endianness
SYSTEM ID EPPROM always store SYSTEM version info in big endian format.
SoC with ARM or PowerPC core should read/write version info from eeprom
in BIG endian format.
So use cpu-specific APIs to read SYSTEM version.
Signed-off-by: Jaiprakash Singh <b44839 at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Bhupesh Sharma [Thu, 28 May 2015 09:24:02 +0000 (14:54 +0530)]
armv8/ls2085a: Increase the supported kernel size
Increases the kernel size supported for LS2085A platforms:-
- Update environment variables
- Add ramdisk_size in bootargs env variable
- Define CONFIG_SYS_BOOTM_LEN to 64MB
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:24:01 +0000 (14:54 +0530)]
armv8/ls2085rdb: Update PCA9547PW slave address
Primary Mux on I2C1 controller has slave address as 0x75.
So update its address.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:24:00 +0000 (14:54 +0530)]
armv8/ls2085qds: Update SFP TX bit as "0" to enable XFI
FPGA BRDCFG9[SFP_TX] should be clear in order to enable XFI ports.
Signed-off-by: Dai Haruki <Dai.Haruki at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:23:59 +0000 (14:53 +0530)]
armv8/ls2085a: call ft_pcie_setup() to change dts status
call ft_pci_setup() to disable PCIe dts node if corresponding
PCIe controller is disabled according to RCW
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:23:58 +0000 (14:53 +0530)]
armv8/ls2085a: Update LS2085a PCIe compatible
Compatible field "fsl,20851a-pcie" is not correct.
So update it to "fsl,ls2085a-pcie"
Signed-off-by: Minghuan Lian <Minghuan.Lian at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:23:57 +0000 (14:53 +0530)]
armv8/ls2085aqds: Add support of SerDes protocol 0x49
SerDes Protocol 0x49 enables 4 SGMII, PEX4, SATA1 and SATA2.
Add support of 0x49 SerDes protocol to enable 4SGMII on slot4 of
ls2085aqds platform.
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 28 May 2015 09:23:56 +0000 (14:53 +0530)]
armv8/ls2085a: Enable "date" command for QDS and RDB
Enable "date" command for QDS and RDB boards
Signed-off-by: Priyanka Jain <Priyanka.Jain at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Yangbo Lu [Thu, 28 May 2015 09:23:55 +0000 (14:53 +0530)]
armv8/ls2085ardb: add hwconfig setting for eSDHC
Add hwconfig setting for eSDHC since it shares some pins with other
IP block.
Signed-off-by: Yangbo Lu <yangbo.lu at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Thu, 28 May 2015 09:23:54 +0000 (14:53 +0530)]
armv8/ls2085ardb: Add eth & phy firmware loading support
Add support for board eth initialization and support for loading phy
firmware. PHY firmware needs to be loaded from board_eth_init() because
all the MACs are not initialized by ldpaa_eth driver.
Signed-off-by: pankaj chauhan <pankaj.chauhan at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Masahiro Yamada [Tue, 14 Jul 2015 16:08:44 +0000 (01:08 +0900)]
libfdt: fix error code of fdt_count_strings()
Currently, this function returns a positive value on error,
so we never know whether this function has succeeded or failed.
For example, if the given property is not found, fdt_getprop()
returns -FDT_ERR_NOTFOUND, and then this function inverts it,
i.e., returns FDT_ERR_NOTFOUND (=1).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes:
bc4147ab2d69 ("fdt: Add a function to count strings")
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 14 Jul 2015 16:08:43 +0000 (01:08 +0900)]
libfdt: fix error code of fdt_get_string_index()
As mentioned in the comment block in include/libfdt.h,
fdt_get_string_index() is supposed to return a negative value
on error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes:
5094eb408a5d ("fdt: Add functions to retrieve strings")
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Tue, 14 Jul 2015 16:08:42 +0000 (01:08 +0900)]
libfdt: fix description of fdt_get_string()
Looks like this comment was copied from that of
fdt_get_string_index().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fixes:
5094eb408a5d ("fdt: Add functions to retrieve strings")
Acked-by: Simon Glass <sjg@chromium.org>
Sudeep Holla [Fri, 10 Jul 2015 16:18:44 +0000 (17:18 +0100)]
cmd_fdt: save fdtaddr in hex format
Commit
90fbee3e4051 ("cmd_fdt: Actually fix fdt command in sandbox")
changed the format(from hex address to unsigned long) in which "fdtaddr"
is saved . However do_fdt continues reads the "fdtaddr" assuming it to
be in hex format. This may lead to fdt being either loaded or attempted
to load at erroneous address generating fault if the address is out of
memory.
This patch changes back the format to hex while saving the "fdtaddr"
as it was done before.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Hua Yanghao <huayanghao@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Haikun Wang [Fri, 26 Jun 2015 11:56:40 +0000 (19:56 +0800)]
fdt: armv8: Fix build warnings on armv8
Fix below build warnings on armv8,
drivers/spi/fsl_dspi.c: In function ‘fsl_dspi_ofdata_to_platdata’:
drivers/spi/fsl_dspi.c:667:2:
warning: format ‘%x’ expects argument of type ‘unsigned int’,
but argument 2 has type ‘fdt_addr_t’ [-Wformat=]
debug("DSPI: regs=0x%x, max-frequency=%d, endianess=%s, num-cs=%d\n",
^
lib/fdtdec.c: In function ‘fdtdec_get_addr_size’:
lib/fdtdec.c:105:4:
warning: format ‘%lx’ expects argument of type ‘long unsigned int’,
but argument 3 has type ‘fdt_size_t’ [-Wformat=]
debug("addr=%08lx, size=%08lx\n",
^
Signed-off-by: Haikun Wang <haikun.wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Andre Przywara [Sat, 20 Jun 2015 23:29:54 +0000 (00:29 +0100)]
fdt: prevent clearing memory node if there are no banks
Avoid clearing the reg property in the memory DT node if no memory
banks have been specified for a board (CONFIG_NR_DRAM_BANKS == 0).
This allows boards to let U-Boot skip the DT memory tinkering in case
other firmware has already setup the node properly before.
This should be safe as all callers of fdt_fixup_memory_banks that use
a computed <banks> value put at least 1 in there.
Add some documentation comments to the header file.
Signed-off-by: Andre Przywara <osp@andrep.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Wed, 15 Jul 2015 14:41:20 +0000 (10:41 -0400)]
Merge git://git.denx.de/u-boot-x86
Bin Meng [Wed, 8 Jul 2015 05:06:41 +0000 (13:06 +0800)]
pci: Disable expansion ROM address decoding when signature check fails
We should not leave the expansion ROM address window open when there
is not a valid ROM.
Suggested-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 8 Jul 2015 05:06:40 +0000 (13:06 +0800)]
pci: Configure expansion ROM during auto config process
Currently PCI expansion ROM address is assigned by a call to
pciauto_setup_rom() outside of the pci auto config process.
This does not work when expansion ROM is on a device behind
PCI bridge where bridge's memory limit register was already
programmed to a value that does not cover the newly assigned
expansion ROM address. To fix this, we should configure the
ROM address during the auto config process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Sat, 16 May 2015 01:33:16 +0000 (09:33 +0800)]
drivers: block: Remove the ata_piix driver
This driver was originally added to support the native IDE mode for
Intel chipset, however it has some bugs like not supporting ATAPI
devices, endianness issue, or even broken build when CONFIG_LAB48.
Given no board is using this driver as of today, rather than fixing
all these issues we just remove it from the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Thu, 9 Jul 2015 10:37:40 +0000 (18:37 +0800)]
x86: Adjust config option order in defconfig for Crown Bay and Minnowmax
Update crownbay_defconfig and minnowmax_defconfig with 'savedefconfig'
result so that the config option order matches Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 07:57:06 +0000 (15:57 +0800)]
tools: ifdtool: Write correct offset on 32-bit machine
On 32-bit machine strtol() returns LONG_MAX which is 0x7fffffff,
which is wrong for u-boot.rom components like u-boot-x86-16bit.bin.
Change to use strtoll() so that it works on both 32-bit and 64-bit
machines.
Reported-by: Fei Wang <wangfei.jimei@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 4 Jul 2015 00:28:28 +0000 (18:28 -0600)]
x86: Add binary blob checksums for Minnowboard MAX
To try to reduce the pain of confusion of binary blobs, add MD5 checksums
for the current versions. This may worsen the situation as new versions
appear, but it should still be possible to obtain these versions, and thus
get a working setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 4 Jul 2015 00:28:27 +0000 (18:28 -0600)]
dm: x86: baytrail: Correct PCI region 3 when driver model is used
Commit
afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 4 Jul 2015 00:28:26 +0000 (18:28 -0600)]
dm: x86: minnowmax: Move PCI to use driver model
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 4 Jul 2015 00:28:25 +0000 (18:28 -0600)]
x86: pci: Tidy up the generic x86 PCI driver
This driver should use the x86 PCI configuration functions. Also adjust its
compatible string to something generic (i.e. without a vendor name).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 4 Jul 2015 00:28:24 +0000 (18:28 -0600)]
x86: Add ROM image description for minnowmax
The layout of the ROM is a bit hard to discover by reading the code. Add
a table to make it easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 4 Jul 2015 00:28:23 +0000 (18:28 -0600)]
dm: spi: Enable environment for minnowmax
Enable a SPI environment and store it in a suitable place.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Simon Glass [Sat, 4 Jul 2015 00:28:22 +0000 (18:28 -0600)]
dm: spi: Correct BIOS protection logic for ICH9
The logic is incorrect and currently has no effect. Fix it so that we can
write to SPI flash, since by default it is write-protected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Simon Glass [Sat, 4 Jul 2015 00:28:21 +0000 (18:28 -0600)]
dm: spi: Correct status register access width
The status register on ICH9 is a single byte, so use byte access when
writing to it, to avoid updating the control register also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Bin Meng [Mon, 6 Jul 2015 08:31:36 +0000 (16:31 +0800)]
x86: Configure VESA parameters before loading Linux kernel
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
Bin Meng [Mon, 6 Jul 2015 08:31:35 +0000 (16:31 +0800)]
x86: crownbay: Enable graphics support
Enable graphics support on Intel Crown Bay board With the help of
vgabios for Intel TunnelCreek IGD. Tested with an external LVDS
panel connected to X4 connector and SDVO adapter connected to X9
connector on the board.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:34 +0000 (16:31 +0800)]
x86: Remove MARK_GRAPHICS_MEM_WRCOMB
MARK_GRAPHICS_MEM_WRCOMB is not referenced anywhere in the code,
hence remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:33 +0000 (16:31 +0800)]
x86: Move VGA option rom macros to Kconfig
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:32 +0000 (16:31 +0800)]
x86: cmd_mtrr: Improve MTRR list information
Print the meaningful base address and mask of an MTRR range without showing
the memory type encoding or valid bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:31 +0000 (16:31 +0800)]
x86: queensbay: Change CPU_ADDR_BITS to 32
Per CPUID:80000008h result, the maximum physical address bits of
TunnelCreek processor is 32 instead of default 36. This will fix
the incorrect decoding of MTRR range mask.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:30 +0000 (16:31 +0800)]
x86: Setup fixed range MTRRs for legacy regions
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Jian Luo [Mon, 6 Jul 2015 08:31:29 +0000 (16:31 +0800)]
video: Add 32-bit color depth support for VBE
The TunnelCreek IGD VBE reports 32-bit color depth regardless 24-bit
color depth is configured. Since 24-bit mode already uses 4 bytes
internally, it should be OK to just add this option in switch case.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Jian Luo [Mon, 6 Jul 2015 08:31:28 +0000 (16:31 +0800)]
x86: bios: Allow pci config read/write to host bridge in int1a_handler
We should allow pci config read/write to host bridge (b.d.f = 0.0.0)
in the int1a_handler() which is a valid pci device.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Jian Luo [Mon, 6 Jul 2015 08:42:06 +0000 (16:42 +0800)]
x86: bios: Synchronize stack between real and protected mode
PCI option rom may use different SS during its execution, so it is not
safe to assume esp pointed to the same location in the protected mode.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Mon, 6 Jul 2015 08:31:26 +0000 (16:31 +0800)]
video: vesa_fb: Look up VGA device by class instead of id
Per PCI spec, VGA device reports its class as standard 030000h in
its configuration space, so we can use it to determine if we need
run option rom instead of testing the supported vendor/device ids.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 7 Jun 2015 14:50:41 +0000 (08:50 -0600)]
dm: pci: Correct bus number when scanning sub-buses
The sub-bus passed to pciauto_prescan_setup_bridge() is incorrect. Fix it
so that sub-buses are numbered correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 7 Jun 2015 14:50:40 +0000 (08:50 -0600)]
dm: pci: Use the correct hose when configuring devices
Only the PCI controller has access to the PCI region information. Make sure
to use the controller (rather than any attached bridges) when configuring
devices.
This corrects a failure to scan and configure devices when driver model is
enabled for PCI.
Also add a comment to explain the problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:55 +0000 (12:18 +0800)]
x86: queensbay: Change PCIe root ports' interrupt routing
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:54 +0000 (12:18 +0800)]
x86: crownbay: Enable writing MP table
Enable writing MP table for Intel Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:53 +0000 (12:18 +0800)]
x86: Update README.x86 for SMP support
Document U-Boot multi-processor support as well as configuration
tables like SFI and MP tables for SMP OS kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:52 +0000 (12:18 +0800)]
x86: Generate a valid MultiProcessor (MP) table
Implement write_mp_table() to create a minimal working MP table.
This includes an MP floating table, a configuration table header
and all of the 5 base configuration table entries. The I/O interrupt
assignment table entry is created based on the same information used
in the creation of PIRQ routing table from device tree. A check
duplicated entry logic is applied to prevent writing multiple I/O
interrupt entries with the same information.
Use a Kconfig option GENERATE_MP_TABLE to tell U-Boot whether we
need actually write the MP table at the F seg, just like we did for
PIRQ routing and SFI tables. With MP table existence, linux kernel
will switch to I/O APIC and local APIC to process all the peripheral
interrupts instead of 8259 PICs. This takes full advantage of the
multicore hardware and the SMP kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:51 +0000 (12:18 +0800)]
x86: Add MultiProcessor (MP) table APIs
The MP table provides a way for the operating system to support
for symmetric multiprocessing as well as symmetric I/O interrupt
handling with the local APIC and I/O APIC. We provide a bunch of
APIs for U-Boot to write the floating table, configuration table
header as well as base and extended table entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:50 +0000 (12:18 +0800)]
x86: Remove inline for lapic access routines
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bin Meng [Tue, 23 Jun 2015 04:18:49 +0000 (12:18 +0800)]
x86: Add I/O APIC register access routines
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>