Fabio Estevam [Wed, 22 Nov 2017 13:15:28 +0000 (11:15 -0200)]
mx6sxsabresd: Use PARTUUID to specify the rootfs location
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Fabio Estevam [Thu, 23 Nov 2017 12:55:33 +0000 (10:55 -0200)]
imx: Remove boolean parameter from wdog powerdown function
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Thu, 23 Nov 2017 11:18:54 +0000 (09:18 -0200)]
imx: Also clear powerdown enable bit for WDOG3 on i.MX6ULL
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Thu, 23 Nov 2017 11:18:53 +0000 (09:18 -0200)]
mx6ull: Fix WDOG3 base address
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Wed, 15 Nov 2017 19:04:04 +0000 (17:04 -0200)]
mx6sabreauto: Remove unneeded SPL selection
SPL option is already selected via Kconfig, so remove it from the
CONFIG_SYS_EXTRA_OPTIONS line.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Wed, 15 Nov 2017 19:04:03 +0000 (17:04 -0200)]
mx6: Select MX6QDL option via Kconfig
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Peter Senna Tschudin [Mon, 6 Nov 2017 19:14:11 +0000 (19:14 +0000)]
mx53: Add Board support for GE PPD
Create board support for GE PPD, based on mx53loco.
Use mx53ppd_defconfig make target to configure for this board.
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Martyn Welch [Wed, 8 Nov 2017 15:35:15 +0000 (15:35 +0000)]
board: ge: make VPD code common
The VPD data is used on a number of GE products. Move the parsing code to
a common location so that we can share this code.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Stefano Babic <sbabic@denx.de>
Nandor Han [Wed, 8 Nov 2017 15:35:14 +0000 (15:35 +0000)]
rtc: add support for s35392a
Add support for S35392A RTC. The driver supports both U-Boot driver
models.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Heiko Schocher <hs@denx.de>
Ian Ray [Wed, 8 Nov 2017 15:35:13 +0000 (15:35 +0000)]
bootcount: add support for bootcounter on EXT filesystem
Add support for bootcounter on an EXT filesystem.
Sync configuration whitelist.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Martyn Welch [Wed, 8 Nov 2017 15:35:12 +0000 (15:35 +0000)]
arm: mx5: Add more register definitions
Add register definitions require for video configuration.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Martyn Welch [Wed, 8 Nov 2017 15:35:11 +0000 (15:35 +0000)]
pwm: imx: Enable PWM support on i.MX53
Add missing parts for i.MX53 PWM support
Acked-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Ian Ray [Wed, 8 Nov 2017 15:35:10 +0000 (15:35 +0000)]
ext4: recover from filesystem corruption when reading
Some fixes when reading EXT files and directory entries were identified
after using e2fuzz to corrupt an EXT3 filesystem:
- Stop reading directory entries if the offset becomes badly aligned.
- Avoid overwriting memory by clamping the length used to zero the buffer
in ext4fs_read_file. Also sanity check blocksize.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Nandor Han [Wed, 8 Nov 2017 15:35:09 +0000 (15:35 +0000)]
imx: mxc_i2c: tweak the i2c transfer method
Tweak the i2c transfer to work for devices that want to read data
without addressing a register.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Sun, 19 Nov 2017 14:21:44 +0000 (12:21 -0200)]
Revert "wandboard: Remove unnecessary delay"
This reverts commit
b8b9790e23a7d6eec08d66192853ecb61bcae095.
Some wandboard variants no longer boot after this commit, so keep
the original delay to avoid the boot regression.
Reported-by: Varga Zsolt <vazso@vazso.hu>
Tested-by: Varga Zsolt <vazso@vazso.hu>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Berton [Thu, 16 Nov 2017 11:59:49 +0000 (09:59 -0200)]
pico-imx6ul: Use FS_GENERIC load command
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Berton [Thu, 16 Nov 2017 11:59:48 +0000 (09:59 -0200)]
pico-imx6ul: Add function to create gpt partitions
Command run setup_emmc will create gpt partitions for mmc 0 device
based on patitions variable.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Berton [Thu, 16 Nov 2017 11:59:47 +0000 (09:59 -0200)]
pico-imx6ul: Define partition layout in the environment
Create layout with a boot 16MiB partition and rootfs with remain
space.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Berton [Thu, 16 Nov 2017 11:59:46 +0000 (09:59 -0200)]
pico-imx6ul: Add boot and rootfs dfu_alt_info
Change dfu_alt_info variable to use the following altsetting:
uboot: To flash raw U-Boot
/zImage: boot: To copy kernel image
/imx6ul-pico-hobbit.dtb: To copy dtb file
rootfs: To copy rootfs
List the currently attached DFU capable USB devices running:
sudo dfu-util -l
Flash U-Boot:
sudo dfu-util -D u-boot.imx -a uboot
Copy boot files:
sudo dfu-util -D zImage -a /zImage
sudo dfu-util -D imx6ul-pico-hobbit.dtb -a /imx6ul-pico-hobbit.dtb
Flash rootfs:
sudo dfu-util -D rootfs.ext4 -a rootfs
To copy boot files you need to have a formated mmc 0:1 partition. To
format with ext4 filesystem you can use ums.
Run on target:
ums 0 mmc 0
and on host:
sudo mkfs.ext4 /dev/sdx1
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Fabio Berton [Thu, 16 Nov 2017 11:59:45 +0000 (09:59 -0200)]
pico-imx6ul: Use PARTUUID to specify the rootfs location
Currently the rootfs location is passed via mmcblk number and using
the UUID method to specify the rootfs location is a better approach
working even if mmcblk number for the eMMC changes depending on the
kernel versions.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Berton [Thu, 16 Nov 2017 11:59:44 +0000 (09:59 -0200)]
pico-imx6ul: Move dfu_alt_info to CONFIG_DFU_ENV_SETTINGS variable
Create CONFIG_DFU_ENV_SETTINGS to set dfu environment settings to
improve human readable code.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Marek Vasut [Thu, 9 Nov 2017 10:50:13 +0000 (11:50 +0100)]
ARM: imx6: Adjust DDR DRAM settings on DHCOM i.MX6 PDK
The board uses T-topology for the four x16 DRAM chips, so remove
the write-leveling from the SPL as that is only usefly on fly-by
topology and can be harmful on T-topology. Also update the DRAM
timing with values from calibration on multiple boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Tom Rini [Tue, 14 Nov 2017 01:08:06 +0000 (20:08 -0500)]
Prepare v2017.11
Signed-off-by: Tom Rini <trini@konsulko.com>
Soeren Moch [Sat, 4 Nov 2017 15:14:09 +0000 (16:14 +0100)]
Revert "console: simplify puts()"
This reverts commit
c61d0009feb966e0e93254a8c435a1889085e6b8.
A tbs2910 board user reported a very slow console frambuffer as
regression in current u-boot. I could bisect this down to the
above mentioned commit.
This revert brings back the fast framebuffer console (one
cache flush per string in puts(), not after each char).
Reported-by: Uwe Scheffler <scheffler.u@web.de>
Signed-off-by: Soeren Moch <smoch@web.de>
Tested-by: Uwe Scheffler <scheffler.u@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Angelo Dureghello [Thu, 2 Nov 2017 19:54:59 +0000 (20:54 +0100)]
board: sysam: stmark2: add missing environment location
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Marek Vasut [Thu, 9 Nov 2017 18:58:40 +0000 (19:58 +0100)]
ARM: rmobile: Fix eMMC signal voltage on Salvator-X/XS
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for Salvator-X/XS to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Fri, 10 Nov 2017 15:04:21 +0000 (10:04 -0500)]
Merge git://git.denx.de/u-boot-sunxi
Werner Böllmann [Fri, 10 Nov 2017 13:44:20 +0000 (19:14 +0530)]
sunxi: SATA link timeout fix
After updating u-boot from v2016.01 to 2017.09, issue with
"SATA link 0 timeout." on my Cubietruck board.
mdelay milled after moving satapwr code to board.
"sunxi: Turn satapwr on from board_init"
(sha1:
9fbb0c3aa49f4604b0342cb527a6bd099f92eaeb)
After adding the "mdelay(500);"
line that was lost in the path the error is gone.
Signed-off-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
[Rebased and updated change and commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Chen-Yu Tsai [Fri, 22 Sep 2017 07:26:33 +0000 (15:26 +0800)]
net: sun8i_emac: Fix build for non-H3/H5 SoCs
Only the H3/H5 SoCs have an internal PHY and its related clock and
reset controls.
Use an #ifdef to guard the internal PHY control code block so it
can be built for other SoCs, such as the A83T or A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tom Rini [Fri, 10 Nov 2017 13:19:01 +0000 (08:19 -0500)]
Merge git://git.denx.de/u-boot-rockchip
Jagan Teki [Fri, 10 Nov 2017 11:48:44 +0000 (17:18 +0530)]
rockchip: configs: vyasa: Update falcon offsets
Update the falcon offsets for args to 16MB and kernel to 17MB
Since the below commit updated U-Boot proper location along
with rockchip boot image offsets
"spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip"
(sha1:
8f4d62b403db45dfa8b1cadb9da9096c79b7df47)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Jagan Teki [Fri, 10 Nov 2017 11:48:43 +0000 (17:18 +0530)]
rockchip: doc: Fix U-Boot proper location for falcon
This patch fixed U-Boot proper location has been
missed to update in bewlo commit
"rockchip: doc: update U-Boot location info"
(sha1:
73e6dbe855f357a8330cfd53ff3033303611c1ad)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Goldschmidt Simon [Fri, 10 Nov 2017 11:38:32 +0000 (11:38 +0000)]
rockchip: doc: update U-Boot location info
The U-Boot location has been moved to block 16384.
This is 8MB, not 4MB.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Thu, 9 Nov 2017 13:11:40 +0000 (08:11 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sunxi
Tom Rini [Thu, 9 Nov 2017 13:11:30 +0000 (08:11 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Lukasz Majewski [Tue, 7 Nov 2017 10:34:17 +0000 (11:34 +0100)]
imx7: Add include guards for include/asm/arch-mx7/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Tue, 7 Nov 2017 10:34:16 +0000 (11:34 +0100)]
imx5: Add include guards for include/asm/arch-mx5/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Tue, 7 Nov 2017 10:34:15 +0000 (11:34 +0100)]
imx6: Add include guards for include/asm/arch-mx6/sys_proto.h file
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Tue, 31 Oct 2017 16:58:05 +0000 (17:58 +0100)]
imx:display5: Add support for LWN's DISPLAY5 board
This commit provides support for LWN's IMX6Q based DISPLAY5 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Tue, 31 Oct 2017 12:26:24 +0000 (13:26 +0100)]
imx6: iomux: Add generic function to set RGMII IO voltage on IMX6 SoCs
This commit provides generic function to set the RGMII/HSIC IO voltage
level on iMX6 devices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Tue, 7 Nov 2017 10:10:29 +0000 (11:10 +0100)]
board: imx6: marsboard: Remove doubled #include <asm/arch/sys_proto.h>
The sys_proto.h file has been included earlier in this file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Artturi Alm [Wed, 8 Nov 2017 03:08:58 +0000 (05:08 +0200)]
sunxi: restore PHYLIB for CONFIG_SUN4I_EMAC users
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h,
likely missed in:
commit
3146f0c017df ("Move PHYLIB to Kconfig")
Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Artturi Alm [Wed, 8 Nov 2017 03:08:57 +0000 (05:08 +0200)]
sunxi: fix CONFIG_SUNXI_EMAC references
fixes CONFIG_SUNXI_EMAC references from drivers/net/Makefile and
include/configs/sunxi-common.h likely forgotten in:
commit
abc3e4df59f5 ("sunxi: Convert SUNXI_EMAC to Kconfig")
Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Benoît Thébaudeau [Sun, 29 Oct 2017 21:08:58 +0000 (22:08 +0100)]
mmc: fsl_esdhc: Fix PIO timeout
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Jagan Teki [Mon, 30 Oct 2017 09:57:09 +0000 (15:27 +0530)]
i.MX6: engicam: Fix MAINTAINERS/README
- Update newly added include/configs file in MAINTAINERS
- Update newly added defconfig file in README
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fabio Estevam [Fri, 3 Nov 2017 15:40:10 +0000 (13:40 -0200)]
mx51: Select the ESDHC_A001 erratum
When a high speed card is connected to mx51evk the following error is seen:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.
Successfully tested with a high speed SD card on a mx51evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Fabio Estevam [Fri, 3 Nov 2017 15:40:09 +0000 (13:40 -0200)]
mx25: Select the ESDHC_A001 erratum
When a high speed card is connected to mx25 the following error is seen:
U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
No arch specific invalidate_icache_all available!
MMC: FSL_SDHC: 0
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
, which prevents any usage of the SD card.
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
Successfully tested with a high speed SD card on a mx25pdk board.
Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
Fabio Estevam [Fri, 3 Nov 2017 15:40:08 +0000 (13:40 -0200)]
mx25: Move MX25 selection to Kconfig
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Kever Yang [Thu, 2 Nov 2017 07:16:36 +0000 (15:16 +0800)]
rockchip: remove SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR from defconfig
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead
of define a new one.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 2 Nov 2017 07:16:35 +0000 (15:16 +0800)]
rockchip: doc: update U-Boot location info
Update rockchip U-Boot location to 0x4000/16384.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 2 Nov 2017 07:16:34 +0000 (15:16 +0800)]
spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip
Rockchip use a 'loader2' partition for U-Boot, so u-boot.bin or
u-boot.itb load by SPL need to locate at0x4000. Detail here:
http://opensource.rock-chips.com/wiki_Boot_option
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Klaus Goger [Mon, 6 Nov 2017 22:02:56 +0000 (23:02 +0100)]
rockchip: board: puma_rk3399: make env location selectable via Kconfig
The environment storage location is selectable via Kconfig. We support
eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store
the environment in the SPI-NOR additional to the default eMMC location.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Klaus Goger [Mon, 6 Nov 2017 22:02:55 +0000 (23:02 +0100)]
rockchip: dts: rk3399: change sd-card io voltage to 3.0V
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Klaus Goger [Mon, 6 Nov 2017 22:02:54 +0000 (23:02 +0100)]
rockchip: dts: Use defines for pin names in rk3399-puma.dtsi and rk3368-lion.dts
pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 6 Nov 2017 22:02:53 +0000 (23:02 +0100)]
rockchip: dts: rk3399-puma: update USB configuration
This change updates the USB configuration for the RK3399-Q7 in the DTS:
* fixes the OTG board configuration by enabling it ('okay')
* improves the speed of 'usb start' by disabling the unused EHCI/OHCI
controllers
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Philipp Tomsich [Mon, 6 Nov 2017 22:02:52 +0000 (23:02 +0100)]
rockchip: dts: rk3399-puma: update usbhub_enable regulator
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
* the GPIO polarity is GPIO_ACTIVE_LOW
* should be set to inactive (enable-active-low) when boot-on settings
are applied
* it can be changed at runtime (i.e. remove the always-on)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Philipp Tomsich [Mon, 6 Nov 2017 22:02:51 +0000 (23:02 +0100)]
rockchip: dts: rk3399-puma: fix the modelling of BIOS_DISABLE
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.
This fixes the mix-up and models it correctly:
* the GPIO is low-active
* the regulator should be enabled (enable-active-high) during
boot-on initialisation
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Kever Yang [Tue, 31 Oct 2017 07:52:20 +0000 (15:52 +0800)]
rockchip: config: use common CONFIG_ENV_SIZE for all SoCs
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Tue, 31 Oct 2017 07:52:19 +0000 (15:52 +0800)]
rockchip: config: sync the ENV offset from rockchip legacy U-Boot
Using the ENV offset from rockchip legacy U-Boot for all SoCs,
the offset is 4MB-32KB
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Fri, 3 Nov 2017 08:11:04 +0000 (16:11 +0800)]
rockchip: rock: remove CONFIG_ENV_OFFSET
We use the same default ENV setting in rockchip_common.h for all SoC.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Mon, 6 Nov 2017 23:25:37 +0000 (18:25 -0500)]
Prepare v2017.11-rc4
Signed-off-by: Tom Rini <trini@konsulko.com>
Chris Brandt [Fri, 3 Nov 2017 15:36:12 +0000 (10:36 -0500)]
cosmetic: rmobile: renesas spelled wrong
Renesas was spelled wrong.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Jan Kundrát [Fri, 3 Nov 2017 02:06:35 +0000 (03:06 +0100)]
Do not attempt to use the systemwide libfdt
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Angelo Dureghello [Fri, 3 Nov 2017 00:35:34 +0000 (01:35 +0100)]
m68k: doc: update outdated documentation
Update m68k documentation to reflect the current ColdFire
architecture support status.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Shawn Guo [Thu, 2 Nov 2017 08:46:34 +0000 (16:46 +0800)]
disk: part_dos: fix part_get_info_extended() function
The check in part_get_info_extended() for a successful partition
searching misses a condition for extended partition. In case of
(ext_part_sector == 0), we should anyway mark the partition as found,
even if it's an extended partition, i.e. (is_extended(pt->sys_ind) == 0).
Otherwise, the extended partition (type 0x0f) will never be identified,
and the following recursive call to part_get_info_extended() will get a
wrong 'part_num' and 'which_part' parameter. In the end, all those
partitions in extended table will not be identified.
Let's add the missing OR condition of (ext_part_sector == 0) for
is_extended() check to fix the problem.
The issue is discovered by running fastboot flash to an extended
partition on eMMC.
$ fastboot flash mmcsda5 cache.img
target reported max download size of
536870912 bytes
sending 'mmcsda5' (18796 KB)...
OKAY [ 2.144s]
writing 'mmcsda5'...
FAILED (remote: cannot find partition)
finished. total time: 2.261s
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Lukasz Majewski [Fri, 27 Oct 2017 10:28:10 +0000 (12:28 +0200)]
gpt: Use cache aligned buffers for gpt_h and gpt_e
Before this patch one could receive following errors when executing
"gpt write" command on machine with cache enabled:
display5 factory > gpt write mmc ${mmcdev} ${partitions}
Writing GPT:
CACHE: Misaligned operation at range [
4ef8f7f0,
4ef8f9f0]
CACHE: Misaligned operation at range [
4ef8f9f8,
4ef939f8]
CACHE: Misaligned operation at range [
4ef8f9f8,
4ef939f8]
CACHE: Misaligned operation at range [
4ef8f7f0,
4ef8f9f0]
success!
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Masahiro Yamada [Fri, 27 Oct 2017 06:04:21 +0000 (15:04 +0900)]
tools: image: fix message when fail to add verification data for config
This function is called when signing configuration nodes. Adjust
the error message.
I do not know why we do not need to show the error message in case of
ENOSPC. Remove the if-conditional that seems unnecessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 27 Oct 2017 06:04:20 +0000 (15:04 +0900)]
tools: image: allow to sign image nodes without -K option
If -K option is missing when you sign image nodes, it fails with
an unclear error message:
tools/mkimage Can't add hashes to FIT blob: -1
It is hard to figure out the cause of the failure.
In contrast, when you sign configuration nodes, -K is optional because
fit_config_process_sig() returns successfully if keydest is unset.
Probably this is a preferred behavior when you want to update FIT with
the same key; you do not have to update the public key in this case.
So, this commit changes fit_image_process_sig() to continue signing
without keydest. If ->add_verify_data() fails, show a clearer error
message, which has been borrowed from fit_config_process_sig().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 27 Oct 2017 04:25:21 +0000 (13:25 +0900)]
tools: image: fix "algo" property of public key for verified boot
The "algo_name" points to a property in a blob being edited. The
pointer becomes stale when fit_image_write_sig() inserts signatures.
Then crypto->add_verify_data() writes wrong data to the public key
destination.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Stephen Warren [Fri, 27 Oct 2017 00:23:35 +0000 (18:23 -0600)]
test/py: regenerate persistent GPT image if code changes
test_gpt generates a persistent disk image which can be re-used across
multiple test runs. Currently, if the Python code that generates the disk
image change, the image is not regenerated, which could cause test
failures e.g. if a test was updated to expect some new partition name or
size, yet the persistent disk image contained the old name or size. This
change introduces functionality to regenerate the disk image if the
instructions to generate the image have changed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stefan Agner [Thu, 26 Oct 2017 12:57:53 +0000 (14:57 +0200)]
tools: env: allow to print U-Boot version
The fw_env utility family has a default environment compiled in
which ties it quite strongly to the U-Boot source/config it has
been built with. Allow to display the U-Boot version it has been
built with using the -v/--version argument.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Masahiro Yamada [Mon, 23 Oct 2017 01:03:40 +0000 (10:03 +0900)]
image-sig: use designated initializers for algorithm
Designated initializers are more readable because we do not
have to check the order in the struct definitions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sat, 21 Oct 2017 16:54:02 +0000 (12:54 -0400)]
MAINTAINERS: Add missing boards and config entries
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.
Signed-off-by: Tom Rini <trini@konsulko.com>
Patrice Chotard [Mon, 23 Oct 2017 07:54:01 +0000 (09:54 +0200)]
tpm: st33zp24: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights header
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Mon, 23 Oct 2017 07:54:00 +0000 (09:54 +0200)]
spear: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for SPEAR
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Mon, 23 Oct 2017 07:53:59 +0000 (09:53 +0200)]
stv0991: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STV0991
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Mon, 23 Oct 2017 07:53:58 +0000 (09:53 +0200)]
stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Mon, 23 Oct 2017 07:53:57 +0000 (09:53 +0200)]
sti: fix STMicroelectronics copyright
Uniformize all STMicroelectronics copyrights headers for STi
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tom Rini [Mon, 6 Nov 2017 14:24:55 +0000 (09:24 -0500)]
Merge git://git.denx.de/u-boot-samsung
Icenowy Zheng [Wed, 1 Nov 2017 14:18:06 +0000 (22:18 +0800)]
video: sunxi: de2: fix SimpleFB node creation when HDMI not initialized
When HDMI is not initialized (e.g. no monitor is plugged), the current
SimpleFB code will still create a broken SimpleFB node.
Detect whether HDMI is initialized when creating SimpleFB node.
Fixes:
be5b96f0e411 ("sunxi: setup simplefb for Allwinner DE2")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Dongjin Kim [Sun, 29 Oct 2017 16:39:59 +0000 (12:39 -0400)]
ARM: dts: exynos: fix property values of LDO15/17 for ODROID-XU3/4
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom Rini [Sun, 22 Oct 2017 21:55:07 +0000 (17:55 -0400)]
Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 3 Nov 2017 14:02:29 +0000 (10:02 -0400)]
Merge tag 'xilinx-fixes-for-v2017.11' of git://denx.de/git/u-boot-microblaze
Xilinx fix for v2017.11
- Fix ceva sata initialization
Michal Simek [Thu, 2 Nov 2017 14:45:34 +0000 (15:45 +0100)]
scsi: ceva: Start port in probe
The patch:
"dm: ahci: Unwind the confusing init code"
(sha1:
7cf1afce7fa3fe64189020fe14b93f7326dd0758)
introduce bug for ceva sata because port didn't start.
On the other hand the dwc_ahci.c was fixed correctly.
Do the same change for ceva too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Tom Rini [Wed, 1 Nov 2017 13:32:14 +0000 (09:32 -0400)]
Merge git://git.denx.de/u-boot-rockchip
Philipp Tomsich [Mon, 30 Oct 2017 13:44:54 +0000 (14:44 +0100)]
rockchip: lion-rk3368: defconfig: select PHY_MICREL_KSZ90X1
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1
in the associated defconfig.
References:
da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 30 Oct 2017 13:44:55 +0000 (14:44 +0100)]
rockchip: puma-rk3399: defconfig: select PHY_MICREL_KSZ90X1
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1
in the associated defconfig (this somehow got lost with
da3b9e7f).
References:
da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 26 Oct 2017 06:45:02 +0000 (14:45 +0800)]
rockchip: evb-rk3328: remove CONFIG_ENV_OFFSET
Remove CONFIG_ENV_OFFSET for there already have one in rockchip_common.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Wed, 25 Oct 2017 08:24:48 +0000 (16:24 +0800)]
rockchip: rk3328: fix rockchip_get_cru api
The API for get priv pointer is wrong, fix it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Kever Yang [Thu, 12 Oct 2017 07:27:29 +0000 (15:27 +0800)]
rockchip: rk3399: init CPU clock when rkclk_init()
Init the CPU and its buses to speed up the boot time.
Move rkclk_init() to a place after rk3399_configure_cpu has defined
at the same time, or else there will be a warning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Klaus Goger [Fri, 6 Oct 2017 17:24:08 +0000 (19:24 +0200)]
rockchip: configs: only add available BOOT_TARGET_DEVICES
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Klaus Goger [Fri, 6 Oct 2017 17:24:09 +0000 (19:24 +0200)]
rockchip: configs: use rockchip-common.h for rk3368
rockchip-common.h already defines values that are missing from
rk3368_common.h
For example BOOT_TARGET_DEVICES was defined empty and therefore
distroboot had no boot targets.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Tue, 31 Oct 2017 12:14:53 +0000 (08:14 -0400)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Fabio Estevam [Tue, 10 Oct 2017 16:43:42 +0000 (13:43 -0300)]
mx6slevk: Call gpio_request()
We should call gpio_request() prior to reading the GPIO value.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Sun, 15 Oct 2017 13:21:07 +0000 (11:21 -0200)]
udoo: Remove cpu type check prior to setup_sata()
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fabio Estevam [Sun, 15 Oct 2017 13:21:06 +0000 (11:21 -0200)]
wandboard: Remove cpu type check prior to setup_sata()
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
This also brings the benefit to allowing setup_sata() to be called for the
mx6qp wandboard variant.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Marek Vasut [Sun, 22 Oct 2017 08:22:40 +0000 (10:22 +0200)]
ARM: imx6: Enable UMS and DFU on DHCOM i.MX6 PDK
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Peng Fan [Thu, 19 Oct 2017 03:13:20 +0000 (11:13 +0800)]
imx: mx6slevk: cleanup board usb code
Since DM_USB enabled, no need the usb code in board file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Fri, 13 Oct 2017 13:27:26 +0000 (10:27 -0300)]
mx6slevk: Fix MMC breakage for the SPL target
Commit
001cdbbb32ef1f6 ("imx: mx6slevk: enable more DM drivers") breaks
MMC support in U-Boot proper on the mx6slevk_spl_defconfig target:
U-Boot SPL 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18)
Trying to boot from MMC1
U-Boot 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18 -0300)
CPU: Freescale i.MX6SL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 33C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
MMC Device 1 not found
*** Warning - No MMC card found, using default environment
As mx6slevk_spl_defconfig does not use CONFIG_DM_MMC and its
board file does not register the mmc controller for U-Boot proper,
let's fix this by adding CONFIG_DM_MMC=y and device tree support.
While at it, add more DM drivers, so that it becomes closer to
mx6slevk_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Fabio Estevam [Sat, 14 Oct 2017 12:17:54 +0000 (09:17 -0300)]
wandboard: Add support for the MX6QP variant
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>