Felix Fietkau [Sun, 28 Aug 2011 19:11:01 +0000 (21:11 +0200)]
mac80211: retry sending failed BAR frames later instead of tearing down aggr
Unfortunately failed BAR tx attempts happen more frequently than I
expected, and the resulting aggregation teardowns cause performance
issues, as the aggregation session does not always get re-established
properly.
Instead of tearing down the entire aggr session, we can simply store the
SSN of the last failed BAR tx attempt, wait for the first successful
tx status event, and then send another BAR with the same SSN.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 17:59:28 +0000 (19:59 +0200)]
b43: LCN-PHY: implement saving and restoring PHY & radio configuration
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 16:47:23 +0000 (18:47 +0200)]
bcma: extract some basic info about board from SPROM
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 16:47:22 +0000 (18:47 +0200)]
ssb: use u16 for storing board rev
Specs say about size 2 (u16) and my 14e4:4727 has board rev 0x1211.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 12:59:58 +0000 (14:59 +0200)]
b43: LCN-PHY: prepare functions for channel switching
Switching is not fully implemented yet, prepare place for the code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 12:28:44 +0000 (14:28 +0200)]
b43: LCN-PHY: implement more PHY ops before radio init
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Sun, 28 Aug 2011 12:28:43 +0000 (14:28 +0200)]
b43: LCN-PHY: add R/W ops for PHY and radio
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 23:52:10 +0000 (01:52 +0200)]
ath9k_hw: do not apply the 2.4 ghz ack timeout workaround to cts
It is only used to workaround interoperability issues related to longer
delays in receiving the block ack, so it is not necessary to apply it
to the CTS exchange.
Should improve throughput slightly, especially when there are lots
of retransmissions.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Javier Cardona [Tue, 6 Sep 2011 19:10:43 +0000 (12:10 -0700)]
mac80211: Defer tranmission of mesh path errors
Under failure conditions, the mesh stack sends PERR messages to the
previous sender of the failed frame. This happens in the tx feedback
path, in which the transmission queue lock may be taken. Avoid a
deadlock by sending the path error via the pending queue.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Dietsche [Sun, 28 Aug 2011 13:22:38 +0000 (08:22 -0500)]
iwlwifi: iwl-agn-rs.c: remove old comment
this comment refers to some code that was removed.
Signed-off-by: Greg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:25 +0000 (00:32 +0200)]
ath9k: defer ath_tx_setup_buffer setup to the first tx attempt during aggr
With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:24 +0000 (00:32 +0200)]
ath9k: move seqno allocation in the tx path to ath_tx_setup_buffer
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:23 +0000 (00:32 +0200)]
ath9k: move the sequence number from ath_frame_info to ath_buf
It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:22 +0000 (00:32 +0200)]
ath9k: clean up the aggregation tid queue
Use a sk_buff_head instead containing skbs instead of a list_head
containing ath_bufs. This makes it easier to decouple the aggregation
code from the ath_buf struct
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 22:32:21 +0000 (00:32 +0200)]
ath9k: use u8 for the tx key index
This saves some space in struct ath_frame_info
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 26 Aug 2011 08:56:39 +0000 (01:56 -0700)]
ath: Make ath_printk void not int and remove unused struct ath_common *
Changing the return type and removing the unused argument from
ath_printk reduces code size.
Add an __always_unused struct ath_common * to the macros
that call ath_printk to avoid unused variable warnings.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1159859 16235 212000 1388094 152e3e drivers/net/wireless/ath/built-in.o.new
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Fri, 26 Aug 2011 08:56:38 +0000 (01:56 -0700)]
ath: Make ath_dbg void not int
The return value is never used so make it void.
Reduces object size a tiny bit.
$ size drivers/net/wireless/ath/built-in.o*
text data bss dec hex filename
1164175 16235 212032 1392442 153f3a drivers/net/wireless/ath/built-in.o.new
1164819 16235 212032 1393086 1541be drivers/net/wireless/ath/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 29 Aug 2011 19:47:58 +0000 (15:47 -0400)]
wl12xx/sdio_test.c: fix build breakage from WL127X_FW_NAME change
Commit
c302b2c959164622558474871ae942da0e484a38 ("wl12xx: Use a single
fw for both STA and AP roles") changed the name of the firmware name
definition, breaking the build of wl12xx/sdio_test.c.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 27 Aug 2011 20:53:42 +0000 (15:53 -0500)]
b43: Fix swatch warning
Swatch reports the following warning for main.c:
CHECK drivers/net/wireless/b43/main.c
drivers/net/wireless/b43/main.c +4115 b43_wireless_core_stop(7) warn: variable dereferenced before check 'dev'
After analysis, this is not a bug, but a false warning. Nonetheless,
a cleanup is in order to prevent some future janitor proposing
the wrong fix, as I did in my original patch.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Sat, 27 Aug 2011 18:56:00 +0000 (13:56 -0500)]
ath9k: Fix a smatch warnings
Smatch shows the following warnings:
CHECK drivers/net/wireless/ath/ath9k/htc_drv_main.c
drivers/net/wireless/ath/ath9k/htc_drv_main.c +1315 ath9k_htc_configure_filter(27) warn: inconsistent returns mutex:&priv->mutex: locked (1303) unlocked (1315)
CHECK drivers/net/wireless/ath/ath9k/ar9003_eeprom.c
drivers/net/wireless/ath/ath9k/ar9003_eeprom.c +3321 ar9300_eeprom_restore_internal(20) warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 27 Aug 2011 10:47:47 +0000 (16:17 +0530)]
ath9k: Add debugfs support for mac/baseband samples
This patch keep track of number of samples that includes
DMA debugs registers, PCU observe, CR, channel noise,
cycle conters, noisefloor history buffer and last N number
of tx and rx descriptor status. These samples are grouped
in table manner which dumping in debgufs.
Debugfs file location:
<debugfs_mnt>/ieee80211/phy#/ath9k/samples
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Sat, 27 Aug 2011 08:25:27 +0000 (10:25 +0200)]
ath9k: fix regression in sending aggregated packets
The recent commit "ath9k: Send legacy rated frames as unaggregated"
introduced a check to ensure that packets with non-MCS rates set in
the rate series will not be aggregated. However, it failed to check
if the rate series is valid before testing the flags, thus breaking
aggregation for normal MCS-only packets if the last series is unset.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 27 Aug 2011 06:43:21 +0000 (12:13 +0530)]
ath9k: Fix eifs/usec timeout for AR9287 v1.3+
For AR9287 v1.3+ chips, MAC runs at 117MHz. But the initvals
IFS parameters are loaded based on 44/88MHz clockrate. So
eifs/usec from ini should not be used for AR9287 v1.3+.
The mentioned values are tested on 2 chain HT40 mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan [Sat, 27 Aug 2011 05:52:59 +0000 (11:22 +0530)]
ath9k_hw: Set default slottime as 9us
Initialize 9us slot time as that is what is used mostly
(for non-ERP cases) and also to be in sync with initvals.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 26 Aug 2011 18:41:40 +0000 (20:41 +0200)]
b43: make HT-PHY support experimental
It was tested on three BCM4331 devices, code has been written from MMIO
dumps only, but seems to be quite stable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafał Miłecki [Fri, 26 Aug 2011 18:41:39 +0000 (20:41 +0200)]
b43: use 8K buffers for 64-bit DMA to workaround hardware bug
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Fri, 26 Aug 2011 18:41:38 +0000 (20:41 +0200)]
b43: Relax requirement for descriptors to be in the DMA zone
When 64-bit DMA was first used, there were problems with the
BCM4311 (14e4:4311). The problem was "fixed" by using the GFP_DMA
flag in the allocation of coherent ring descriptor memory.
The original problem is now believed to have been due to bugs in
the 64-bit DMA implementation in the rest of the kernel, and that
those bugs have been fixed. Accordingly, the requirement for the
descriptors to be in the DMA zone is relaxed.
Bounce buffers are left in the DMA zone.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Fri, 26 Aug 2011 06:34:59 +0000 (14:34 +0800)]
p54spi: add "spi:" prefix for stlc45xx modalias
Since commit
e0626e38 (spi: prefix modalias with "spi:"),
the spi modalias is prefixed with "spi:".
This patch adds "spi:" prefix for modalias of stlc45xx.
Also move it to be group with other modalias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 26 Aug 2011 06:13:56 +0000 (23:13 -0700)]
iwlagn: handle GO powersave
In order to implement support for GO powersave on
the P2P client side, the ucode needs to know what
GO we're trying to authenticate/associate with,
it needs to have a station entry and the BSSID in
the RXON set.
Implement the new mac80211 callbacks to give this
data to the device.
Since this is also useful for the device when a
normal connection is established, also program it
with the information in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:32 +0000 (23:11 -0700)]
iwlagn: move tx queues to transport layer
This finalizes the move of the data path to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:31 +0000 (23:11 -0700)]
iwlagn: move the stop / wake queue logic to transport layer
priv->mac80211_registered and priv->hw needed to move to shared.
stop_queue API was added in order to allow the upper layer to stop
the SW queues for regulatory purposes.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:30 +0000 (23:11 -0700)]
iwlagn: move check_stuck_queue to transport layer
This one is really transport related.
==== moves Stanislaw's code to BSD area ====
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:29 +0000 (23:11 -0700)]
iwlagn: move wait_for_tx_queue_empty to transport layer
This one is really transport related.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:28 +0000 (23:11 -0700)]
iwlagn: cosmetics in iwl-trans.h
Remove a few dereferences of priv from the transport layer while
at it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:27 +0000 (23:11 -0700)]
iwlagn: move the disable agg logic to transport layer
Since all the check_empty logic is now in the transport layer,
the upper layer doesn't need to know anything about tx queues.
The disable aggregation flow was the last to know what a tx queue
is, so move it too.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:26 +0000 (23:11 -0700)]
iwlagn: move the check_empty logic to the transport layer
This logic is responsible to tell mac80211 when the HW queues are
empty and the BA session can be started / torn down.
Fix a bug on the way:
When the the Tx BA session is stopped and the HW queues aren't empty,
we stop the SW queue to drain the HW queue and then switch to the
legacy HW queue. This is the IWL_EMPTYING_HW_QUEUE_DELBA state.
While in this state, we never wake the SW queue, even when the HW
queue is almost empty, since we need to drain it completely. Look
at iwl_trans_pcie_reclaim regarding this.
Once the HW queue is really empty, we must wake the SW queue in order
to get traffic to the legacy queue.
This step was missing leading to an odd situation were the traffic
would just stall after we tore down a Tx BA session while the HW
queue was not empty.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:25 +0000 (23:11 -0700)]
iwlagn: allocate resources for TX BA session in transport
The queues and all the related logic suits to the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:24 +0000 (23:11 -0700)]
iwlagn: move the mapping ac to queue / fifo to transport
This mapping is transport related.
This allows us to remove the notion of tx queue from the tx path in
the upper layer.
iwl_wake_any_queue moved to transport layer since it needs to access
these mappings.
The TX API is nicer now:
int (*tx)(struct iwl_trans *trans, struct sk_buff *skb,
struct iwl_device_cmd *dev_cmd, u8 ctx, u8 sta_id);
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:23 +0000 (23:11 -0700)]
iwlagn: upper layer uses slabs to allocate tx cmds
In a near future, the upper layer won't be aware of the tx queues.
This allows to remove one place where the upper layer needed to
provide the tx queue index to the transport layer.
This also saves around 1.5MB.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:22 +0000 (23:11 -0700)]
iwlagn: set tx_fifo for ampdu in transport layer
the mapping tx_queue -> fifo is really transport related. The upper
layer should be involved in such things.
Note that upon agg_disable, the queue is always mapped to fifo 0, but
this doesn't matter since when the queue will be setup again for a
new BA session, it will be configured to the good fifo anyway.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:21 +0000 (23:11 -0700)]
iwlagn: upper layer stores iwl_rxon_context in skb's CB
This removes the need for iwl_tx_info.
Each tx queue holds an array of skbs, the transport layer doesn't
need to know anything about the context in which a specific skb is
sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:20 +0000 (23:11 -0700)]
iwlagn: stop the device before freeing it
When we remove the module, we free all the tx and rx resources.
Before doing that, we'd better stop the tx / rx activity. Calling
iwl_trans_stop_device in iwl_remove helps also to remove a few API
functions:
* rx_free: happens in iwl_trans_free
* tx_free: happens in iwl_trans_free
* disable_sync_irq: happens in iwl_trans_stop_device
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:19 +0000 (23:11 -0700)]
iwlagn: remove dereferences of priv from transport
There are still quite a few, but much less.
A few fields have been moved /copied to hw_params which sits in the
shared area:
* priv->cfg->base_params->num_of_ampdu_queues
* priv->cfg->base_params->shadow_reg_enable
* priv->cfg->sku
* priv->ucode_owner
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:18 +0000 (23:11 -0700)]
iwlagn: iwl_tid_data moves to iwl-shared
The rate scaling and the transport need to access the data in
iwl_tid_data, hence the move.
Note that the only component in the upper layer that needs this data
is the rate scaling. Refactoring the rate scaling may help to move
iwl_tid_data from the shared area to the transport area.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:11:17 +0000 (23:11 -0700)]
iwlagn: adding special "D" SKU for 2000 series
One more sku for 2000 series with different Subsystem ID
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:16 +0000 (23:11 -0700)]
iwlagn: iwl-pci doesn't include iwl-dev any more
Move all the iwlXXX_abgn_cfg forward declaration to a separate file
so that iwl-pci.c doesn't need to include iwl-agn.h that includes
all iwl-dev.h
This allows to provide real encapsulation. Dereferencing iwl_priv
in the bus layer will now lead to a compilation error.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Halperin [Fri, 26 Aug 2011 06:11:15 +0000 (23:11 -0700)]
iwlagn: fix compile warnings when CONFIG_PM_SLEEP is not set
CC [M] drivers/net/wireless/iwlwifi/iwl-pci.o
drivers/net/wireless/iwlwifi/iwl-pci.c:506: warning: \91iwl_pci_suspend\92 defined but not used
drivers/net/wireless/iwlwifi/iwl-pci.c:519: warning: \91iwl_pci_resume\92 defined but not used
These are only used if CONFIG_PM_SLEEP is enabled. CONFIG_PM depends
(CONFIG_PM_SLEEP || CONFIG_PM_RUNTIME), so it can be set without
CONFIG_PM_SLEEP selected.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:14 +0000 (23:11 -0700)]
iwlagn: all function iwl-io.c receive iwl_bus
Which means that iwl-io.c doesn't need to include iwl-dev.h any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:13 +0000 (23:11 -0700)]
iwlagn: add missing includes
a few h files weren't self contained. Fix that.
Move iwl_dma_ptr to transport layer since it is not used by the upper layer
any more.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:12 +0000 (23:11 -0700)]
iwlagn: move Keep Warm to transport layer
It is relevant for PCIe only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:11 +0000 (23:11 -0700)]
iwlagn: iwl-dev.h doesn't include iwl-fh.h any more
Since iwl-fh.h contains transport related data, it shouldn't be included by the
upper layer.
Only the transport layer and iwl-agn-ucode.c includes it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:10 +0000 (23:11 -0700)]
iwlagn: remove unused parameters from hw_params
Some of them weren't used at all, the others always had the same value since
the driver split.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:09 +0000 (23:11 -0700)]
iwlagn: remove references to priv from the transport layer
Continue to the clean up of the priv dereferencing from the transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:08 +0000 (23:11 -0700)]
iwlagn: move dump_csr and dump_fh to transport layer
These are transport layer related. Move also the corresponding debugfs handlers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:07 +0000 (23:11 -0700)]
iwlagn: move hcmd_lock to transport layer
Since it is needed for host commands only, it is needed in transport layer only
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:06 +0000 (23:11 -0700)]
iwlagn: transport layer should receive iwl_trans
Change a lot of functions to have them receive iwl_trans and not iwl_priv.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:05 +0000 (23:11 -0700)]
iwlagn: move iwl_free_pages to iwl-shared.h
This helper is used by the transport and the upper layer.
Kill __iwl_free_pages which was used in the transport only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:04 +0000 (23:11 -0700)]
iwlagn: move all iwl_is_XXX helpers to iwl-shared.h
Logic move after all priv->status moved to struct iwl_shared
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:03 +0000 (23:11 -0700)]
iwlagn: fix the check of IWLAGN_FIRST_AMPDU_QUEUE
BUILD_BUG_ON(ARRAY_SIZE(iwlagn_ipan_queue_to_tx_fifo) !=
IWLAGN_FIRST_AMPDU_QUEUE);
This check can be buggy. IWLAGN_FIRST_AMPDU_QUEUE has to be greater than the
ARRAY_SIZE of iwlagn_ipan_queue_to_tx_fifo.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:02 +0000 (23:11 -0700)]
iwlagn: move scd_bc_tbls and scd_base_addr to iwl_trans_pcie
Needed for PCIe only
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:01 +0000 (23:11 -0700)]
iwlagn: move reclaim related functions
Now that the reclaim flow has been moved to the transport layer, a lot of
functions can be made static or don't need to be exported outside the transport
layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:11:00 +0000 (23:11 -0700)]
iwlagn: reclaim the packets in transport layer
The reclaim flow is really transport related. Define a simple API to allow the
upper layer to request from the transport layer to reclaim packets until an
index written in the Tx response / BA notification.
The transport layer prepares a list of the packets that are being freed and
passes this list to the upper layer.
Between the two layers, the CB of the skb is used to pass a pointer to the
context (BSS / PAN) in which the skb was sent.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:59 +0000 (23:10 -0700)]
iwlagn: move isr_statistics to transport layer
It is accessed by the transport layer only, hence the move.
The debugfs handlers that accessed it moved to the transport layer too.
The rx_handlers part of it stayed in the upper layer and a special debugfs
has been added for it
Also add missing includes to iwl-commands.h.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:10:58 +0000 (23:10 -0700)]
iwlagn: add comments to module parameters
Add more comments to iwl_mod_params
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:10:57 +0000 (23:10 -0700)]
iwlagn: more comments for bt channel inhibition
Add comments for better description
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:10:56 +0000 (23:10 -0700)]
iwlagn: support small form factor SKU of 6205
Different subsystem ID
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:10:55 +0000 (23:10 -0700)]
iwlagn: enable 11n aggregation without checking traffic load
Enable HT aggregation when it reach reasonable traffic without
checking traffic load which delay enabling the aggregation and lower
the throughput
but this behavior can be overwrite by module parameter
this address
https://bugzilla.kernel.org/show_bug.cgi?id=40042
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:54 +0000 (23:10 -0700)]
iwlagn: move the NIC error flow to the transport layer
It is transport dependent, move to the PCIe transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:53 +0000 (23:10 -0700)]
iwlagn: move ISR related data to transport layer
Since the ISR is entirely in the transport layer, its data should be in the pcie
specific region.
Change sync_irq to first disable and then synchronize the IRQ.
iwl_isr and iwl_isr_ict now receive iwl_trans.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:52 +0000 (23:10 -0700)]
iwlagn: move iwl_suspend / iwl_resume to the transport layer
These flows needs to access the APM and a few other registers that can differ
between different transports.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:51 +0000 (23:10 -0700)]
iwlagn: iwl_rx_queue moves to the iwl_trans_pcie
Since this struct is specific to pcie transport, move it the the pcie
specific transport layer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:50 +0000 (23:10 -0700)]
iwlagn: transport handler can register debugfs entries
Add a handler in iwl_trans_ops to allow it to add entries under debugfs dir
given by the upper level.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:49 +0000 (23:10 -0700)]
iwlagn: add comments to iwl_bus / iwl_trans
Rename the recursive inclusion protection in iwl-bus.h while we are at it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:48 +0000 (23:10 -0700)]
iwlagn: bus layer chooses its transport layer
Remove iwl_transport_register which was a W/A. The bus layer knows what
transport to use. So now, the bus layer gives the upper layer a pointer to the
iwl_trans_ops struct that it wants to use. The upper layer then, allocates the
desired transport layer using iwl_trans_ops->alloc function.
As a result of this, priv->trans, no longer exists, priv holds a pointer to
iwl_shared, which holds a pointer to iwl_trans. This required to change all the
calls to the transport layer from upper layer. While we were at it, trans_X
inlines have been renamed to iwl_trans_X to avoid confusions, which of course
required to rename the functions inside the transport layer because of
conflicts in names. So the static API functions inside the transport layer
implementation have been renamed to iwl_trans_pcie_X.
Until now, the IRQ / Tasklet were initialized in iwl_transport_layer. This is
confusing since the registration doesn't mean to request IRQ, so I added a
handler for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:47 +0000 (23:10 -0700)]
iwlagn: priv->sta_lock moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:46 +0000 (23:10 -0700)]
iwlagn: add IWL_DEBUG_FW_ERRORS
instead of IWL_DEBUG(priv, IWL_DL_FW_ERRORS
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:45 +0000 (23:10 -0700)]
iwlagn: modify the debug macro to be usable by all the layers
Since all the layers need to print debug message, the debug macro cannot suppose
that they will be given iwl_priv as a parameter and then dereference it.
Use iwl_shared instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:44 +0000 (23:10 -0700)]
iwlagn: priv->mutex moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:43 +0000 (23:10 -0700)]
iwlagn: priv->lock moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:42 +0000 (23:10 -0700)]
iwlagn: priv->status moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:41 +0000 (23:10 -0700)]
iwlagn: workqueue moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:40 +0000 (23:10 -0700)]
iwlagn: cmd_queue moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:39 +0000 (23:10 -0700)]
iwlagn: hw_params moves to iwl_shared
Since it is used by all the layers, it needs to move to iwl_shared.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:38 +0000 (23:10 -0700)]
iwlagn: debug_level moves to struct iwl_shared
This will allow all the modules to look at it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:37 +0000 (23:10 -0700)]
iwlagn: introduce struct iwl-shared - known by all layers
This struct will hold pointers to all the layers, so that every layer will find
the pointers it needs when calling another layer.
Note that the drv_data set to struct device is now a pointer to
struct iwl_shared.
This solves of bug that I introduced in
iwlagn: simplify the bus architecture
Bug description:
sysfs gets the the driver data from struct device. Till the aforementioned
patch, dev_get_drvdata would return iwl_priv. After the patch, dev_get_drvdata
return iwl_bus which is buggy since the sysfs handlers rely on this value, and
sysfs handlers need iwl_priv.
Now, dev_get_drvdata return iwl-shared. Since we have pointers to all the
layers in iwl_shared, every layer will be able to get the pointer it needs:
bus layer will gets iwl_bus from the PCI suspend callbacks, and the sysfs
handlers will get the iwl_priv they need.
In order to keep good encapsulation, we need to avoid to dereference iwl_priv
from a different layer. This is why instead of including iwl-dev.h from
iwl-shared.h, I added a forward declaration to iwl_priv. Moreover we keep type
safety while providing encapsulation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:36 +0000 (23:10 -0700)]
iwlagn: introduce iwl-shared.h
It will hold declaration of functions and forward declaration of struct that
are used by several layers.
This will allow modules not to include iwl_priv. iwl_bus and iwl_trans are
still visible to all.
All the layers share the module parameters, move the struct to iwl-shared.h.
Also add all module parameters to iwl_mod_params instead of having them as
global static. This includes
* debug_level
* ant_coupling
* bt_ch_announce
* wanted_ucode_alternative
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 26 Aug 2011 06:10:35 +0000 (23:10 -0700)]
iwlagn: use iwl_get_debug_level instead of iwl_debug_level
The latter may return incomplete information.
For example, if one switched IWL_DL_TX on through sysfs, IWL_DL_TX bit would
have been set in priv->debug_level, but since iwl_alloc_traffic_mem looked at
iwl_debug_level only, it wouldn't have allocated the tx_traffic buffer.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:10:34 +0000 (23:10 -0700)]
iwlagn: remove out-dated comments
Portion of iwl_cfg comments is not correct anymore, remove it.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 26 Aug 2011 06:10:33 +0000 (23:10 -0700)]
iwlagn: Rename iwlcore prefix
There are number of functions with "iwlcore_" prefix which not feels right,
rename those to "iwl_".
No functional changes by making the renames.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Fri, 26 Aug 2011 05:49:57 +0000 (11:19 +0530)]
ath9k: minor cleanup in ani
removed a function declaration, removed a variable, renamed a variable
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Fri, 26 Aug 2011 05:40:01 +0000 (11:10 +0530)]
ath9k: use appropriate debug mask
in the Rx path of the driver it would be better to use ATH_DBG_ANY
rather than ATH_DBG_XMIT for printing debug messages
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Thu, 25 Aug 2011 21:47:35 +0000 (23:47 +0200)]
p54: Use do_div for 64-bit division to fix 32-bit kernels
Use the do_div macro for 64-bit division. Otherwise, the module will
reference __udivdi3 under 32-bit kernels, which is not allowed in
kernel space.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Florian Fainelli [Thu, 25 Aug 2011 19:33:48 +0000 (21:33 +0200)]
ath9k: add missing AR9340 in ath_mac_bb_names
AR9340 is not listed in ath_mac_bb_names, which leads to such a message:
ieee80211 phy0: Atheros AR???? Rev:0 mem=0xb8100000, irq=2
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stanislaw Gruszka [Thu, 25 Aug 2011 15:07:24 +0000 (17:07 +0200)]
cfg80211: document wiphy->registered
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Wed, 24 Aug 2011 19:12:41 +0000 (15:12 -0400)]
mac80211: refactor skb copy to failq in mesh_path_move_to_queue
This seems a bit less awkward...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Peter Huewe [Tue, 7 Jun 2011 20:36:14 +0000 (22:36 +0200)]
net/mac80211/debugfs: Convert to kstrou8_from_user
This patch replaces the code for getting an number from a
userspace buffer by a simple call to kstrou8_from_user.
This makes it easier to read and less error prone.
Since the old buffer was only 10 bytes long and the value is masked by a
nibble-mask anyway, we don't need to use kstrtoul but rather kstrtou8.
Kernel Version: v3.0-rc2
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 29 Aug 2011 18:27:52 +0000 (14:27 -0400)]
Merge branch 'for-linville' of git://git./linux/kernel/git/luca/wl12xx
Luis R. Rodriguez [Tue, 23 Aug 2011 20:37:07 +0000 (13:37 -0700)]
ath9k: add AR9580 support
This has been tested in STA and AP mode by Florian.
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian Lamparter [Thu, 25 Aug 2011 13:00:54 +0000 (15:00 +0200)]
carl9170: Use do_div for 64-bit division to fix 32-bit kernels
Use the do_div macro for 64-bit division. Otherwise, the module will
reference __udivdi3 under 32-bit kernels, which is not allowed in
kernel space.
drivers/built-in.o: In function `carl9170_collect_tally':
cmd.c:191: undefined reference to `__udivdi3'
cmd.c:192: undefined reference to `__udivdi3'
cmd.c:193: undefined reference to `__udivdi3'
Reported-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Wed, 24 Aug 2011 22:36:08 +0000 (15:36 -0700)]
ath9k_hw: add AR9580 support
Here are the AR9580 1.0 initvals checksums using the
Atheros initvals-tools [1]. This is useful for when
we udate the initvals again with other values. It ensures
that we match the same initvals used internally. The
tool is documented on the wiki [2].
$ ./initvals -f ar9580-1p0
0x00000000e912711f ar9580_1p0_modes_fast_clock
0x000000004a488fc7 ar9580_1p0_radio_postamble
0x00000000f3888b02 ar9580_1p0_baseband_core
0x0000000003f783bb ar9580_1p0_mac_postamble
0x0000000094be244a ar9580_1p0_low_ob_db_tx_gain_table
0x0000000094be244a ar9580_1p0_high_power_tx_gain_table
0x0000000090be244a ar9580_1p0_lowest_ob_db_tx_gain_table
0x00000000ed9eaac6 ar9580_1p0_baseband_core_txfir_coeff_japan_2484
0x00000000c4d66d1b ar9580_1p0_mac_core
0x00000000e8e9043a ar9580_1p0_mixed_ob_db_tx_gain_table
0x000000003521a300 ar9580_1p0_wo_xlna_rx_gain_table
0x00000000301fc841 ar9580_1p0_soc_postamble
0x00000000a9a06b3a ar9580_1p0_high_ob_db_tx_gain_table
0x00000000a15ccf1b ar9580_1p0_soc_preamble
0x0000000029495000 ar9580_1p0_rx_gain_table
0x0000000037ac0ee8 ar9580_1p0_radio_core
0x00000000603a1b80 ar9580_1p0_baseband_postamble
0x000000003d8b4396 ar9580_1p0_pcie_phy_clkreq_enable_L1
0x00000000398b4396 ar9580_1p0_pcie_phy_clkreq_disable_L1
0x00000000397b4396 ar9580_1p0_pcie_phy_pll_on_clkreq
[1] git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
[2] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool
Cc: David Quan <dquan@qca.qualcomm.com>
Cc: Kathy Giori <kgiori@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>