Arnd Bergmann [Tue, 19 Oct 2021 22:07:02 +0000 (00:07 +0200)]
Merge tag 'stm32-dt-for-v5.16-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.16, round 1
Highlights:
----------
- MPU:
- ST boards:
- Add new stm32mp135f-dk board. It embedds new STM32MP135 SoC,
with 512 MB of DDR3. Several connections are available on this
board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI,
Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in
this tag.
- Change IRQ level for STUSB1600 on DKx boards.
- Fix SAI subclocks range.
- Add ck_usb0_48m clock in USB OHCI node device to match with
STM32MP15 datasheet.
- DH boards:
- Reduce DHCOR SPI NOR frequency to 50 MHz to avoid sporadic issues.
- Fix SAI pin muxing.
- Odyssey:
- Set DCMI pins.
* tag 'stm32-dt-for-v5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
ARM: dts: stm32: fix SAI sub nodes register range
ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
ARM: dts: stm32: add initial support of stm32mp135f-dk board
dt-bindings: stm32: document stm32mp135f-dk board
ARM: dts: stm32: add STM32MP13 SoCs support
Link: https://lore.kernel.org/r/9d52c3e2-a3b9-89f3-1896-7cd3560e7010@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 22:05:08 +0000 (00:05 +0200)]
Merge tag 'renesas-arm-dt-for-v5.16-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.16 (take two)
- SPI Multi I/O Bus, SDHI, and Ethernet support for the RZ/G2L SoC,
- SPI Multi I/O Bus, camera, and video-on support for the R-Car V3U
SoC,
- SPI FLASH support for the Falcon development board,
- eMMC, microSD, and Ethernet support for the RZ/G2L SMARC EVK
development board,
- 2 GHz High-Performance support for the R-Car H3e-2G, M3e-2G, and
M3Ne-2G SoCs,
- Miscellaneous fixes and improvements.
* tag 'renesas-arm-dt-for-v5.16-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
mailmap: Fix text encoding for Niklas Söderlund
arm64: dts: renesas: rcar-gen3e: Add Cortex-A57 2 GHz opps
arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet
arm64: dts: renesas: r9a07g044: Add GbEthernet nodes
arm64: dts: renesas: Add ports node to all adv7482 nodes
arm64: dts: renesas: r8a779a0: Add and connect all CSI-2, ISP and VIN nodes
arm64: dts: renesas: rzg2l-smarc: Enable microSD on SMARC platform
arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform
arm64: dts: renesas: r9a07g044: Add SDHI nodes
arm64: dts: renesas: falcon-cpu: Add SPI flash via RPC
arm64: dts: renesas: r8a779a0: Add RPC node
arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node
Link: https://lore.kernel.org/r/cover.1634298094.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:58:41 +0000 (23:58 +0200)]
Merge tag 'aspeed-5.16-devicetree' of git://git./linux/kernel/git/joel/bmc into arm/dt
ASPEED device tree updates for 5.15
- New machines:
* TYAN S7106 BMC, a x86 server from about four years ago
- Descriptions for the AST2600 ADC, which now has an upstream driver
- Lots of GPIO line names. The OpenBMC project has adopted a scheme for
naming the lines, and new additions will follow this guide
- New I2C devices for Rainier, Everest, EthanolX, Mt Jade
- Fixes for fp5280g2 which has seen some recent development, including
the addtion of a QEmu machine for testing
* tag 'aspeed-5.16-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/bmc:
ARM: dts: aspeed: fp5280g2: Use the 64M layout
ARM: dts: aspeed: Add TYAN S7106 BMC machine
ARM: dts: aspeed: rainier: Add power-config-full-load gpio
ARM: dts: aspeed: p10bmc: Define secure boot gpio
ARM: dts: aspeed: mtjade: Add some gpios
ARM: dts: aspeed: Add ADC for AST2600 and enable for Rainier and Everest
ARM: dts: everest: Define name for gpio line B6
ARM: dts: everest: Define name for gpio line Q2
ARM: dts: rainier: Define name for gpio line Q2
ARM: dts: everest: Add 'factory-reset-toggle' as GPIOF6
ARM: dts: aspeed: everest: Add I2C bus 15 muxes
ARM: dts: aspeed: rainier: Add system LEDs
ARM: dts: aspeed: amd-ethanolx: Add FRU EEPROM
ARM: dts: fp5280g2: Enable KCS 3 for MCTP binding
Link: https://lore.kernel.org/r/CACPK8XdrMzY9tzdof7KpzxKquTo7GcWW4N9Zqwtmmu73C7htXA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:41:26 +0000 (23:41 +0200)]
Merge tag 'hisi-arm64-dt-for-5.16' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: HiSilicon ARM64 DT updates for 5.16
- Add SPMI PMIC support for the Hikey970 board
- Correct the sp805 watchdog compatible string to match the document
- Correct the operating-points table name to match the dtschema
* tag 'hisi-arm64-dt-for-5.16' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisilicon: align operating-points table name with dtschema
arm64: dts: hisilicon: fix arm,sp805 compatible string
arm64: dts: hisilicon: Add support for Hikey 970 PMIC
Link: https://lore.kernel.org/r/6168EB53.60503@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:40:40 +0000 (23:40 +0200)]
Merge tag 'ux500-dts-for-v5.16' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
Ux500 DTS updates:
- Flag the janice SPI display lines properly for the right line
semantics.
- Fix some errors in the Skomer regulator configuration.
- Fix some SD card pin configurations on Skomer.
- Assign the Skomer SD card a 300 ms power-on delay.
- Rewrite the battery nodes to use the standard binding
"monitored-battery" as used in the updated bindings, and
provide the right Samsung battery compatibles for the Samsung
phones.
* tag 'ux500-dts-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ux500: Switch battery nodes to standard
ARM: dts: ux500: Skomer eMMC needs 300 ms power on
ARM: dts: ux500: Fix up SD card pin config
ARM: dts: ux500: Skomer regulator fixes
ARM: dts: ux500: Tag Janice display SPI correct
Link: https://lore.kernel.org/r/CACRpkdYf5GwRvG1Gemk4mE+aw6UnAVTY8OudwsVNPQXThHXu6g@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:39:15 +0000 (23:39 +0200)]
Merge tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.16, please pull the following:
- Rafal updates the BCM4908 DTS files to produce fewer warnings by
fixing the UART clock name, moving the reboot syscon node out of the bus
node, and finally updating the NAND controller node names.
* tag 'arm-soc/for-5.16/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: broadcom: bcm4908: Fix UART clock name
arm64: dts: broadcom: bcm4908: Move reboot syscon out of bus
arm64: dts: broadcom: bcm4908: Fix NAND node name
Link: https://lore.kernel.org/r/20211013174016.831348-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 21:35:31 +0000 (23:35 +0200)]
Merge tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for 5.16, please pull the following:
- Matthew provides a set of updates to the Northstar Plus Device Tree
files to fix a number of warnings, and prepare the files to support the
addition of the Cisco Meraki MX64/MX65 wireless controller devices and
finally adds support for those boards.
- Rafal continues to provide updates to the BCM5301X Device Tree files
in order to fix warnings with the various node names, MDIO muxes and
memory nodes. He also adds support for the external switches on the
BCM53573 SoC and adds Tenda AC9 switch ports.
- Christian provides the description of the Ethernet switch ports for
the Cisco Meraki MR32 based on the 53016 SoC
- Arinc adds support for the Asus RT-AC88U device based on the BCM4709
and featuring 8 Ethernet ports over the integrated and the external
Realtek switch (not supported yet)
- Stefan adds support for the Raspberry Pi Compute Module 4 IO board and
does a number of preparatory changes to get there to the Device Tree
files before doing the actual addition
* tag 'arm-soc/for-5.16/devicetree' of https://github.com/Broadcom/stblinux: (31 commits)
arm64: dts: broadcom: Add reference to RPi CM4 IO Board
ARM: dts: Add Raspberry Pi Compute Module 4 IO Board
ARM: dts: Add Raspberry Pi Compute Module 4
dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4
ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi
dt-bindings: display: bcm2835: add optional property power-domains
ARM: dts: BCM5301X: Add DT for Asus RT-AC88U
ARM: BCM53016: MR32: get mac-address from nvmem
ARM: BCM53016: Specify switch ports for Meraki MR32
ARM: dts: BCM53573: Add Tenda AC9 switch ports
ARM: dts: BCM53573: Describe on-SoC BCM53125 rev 4 switch
ARM: dts: BCM5301X: Specify switch ports for more devices
ARM: dts: NSP: Fix MX65 MDIO mux warnings
ARM: dts: NSP: Fix MX64/MX65 eeprom node name
ARM: dts: NSP: Fix MDIO mux node names
ARM: dts: NSP: Fix mpcore, mmc node names
ARM: dts: NSP: Add bcm958623hr board name to dts
ARM: dts: BCM5301X: Fix memory nodes names
ARM: dts: BCM5301X: Fix MDIO mux binding
ARM: dts: BCM5301X: Fix nodes names
...
Link: https://lore.kernel.org/r/20211013174016.831348-1-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:57:36 +0000 (22:57 +0200)]
Merge tag 'samsung-dt64-5.16' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.16
1. Match Exynos5433 DTS with dtschema.
2. Add an Exynos Auto v9 SoC and SADK board. The Exynos Auto v9 is a
design for automotive for In-vehicle Infotainments (IVI) and Advanced
Driver-Assistance Systems (ADAS).
This pull request brings very basic support (pinctrl, UART and UFS
storage) with a development SADK (Samsung Automotive Development Kit)
board.
* tag 'samsung-dt64-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add minimal support for exynosautov9 sadk board
arm64: dts: exynos: add initial support for exynosautov9 SoC
arm64: dts: exynos: add proper comaptible FSYS syscon in Exynos5433
arm64: dts: exynos: align operating-points table name with dtschema in Exynos5433
Link: https://lore.kernel.org/r/20211013162418.43072-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:49:26 +0000 (22:49 +0200)]
Merge tag 'samsung-dt-5.16' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.16
Minor cleanups - from undocumented or unused properties, coding style.
* tag 'samsung-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: use spaces instead of tabs around '='
ARM: dts: exynos: remove unneeded DVS voltages from PMIC on Arndale
ARM: dts: exynos: drop undocumented samsung,sata-freq property in Exynos5250
Link: https://lore.kernel.org/r/20211013162418.43072-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:37:09 +0000 (22:37 +0200)]
Merge tag 'qcom-arm64-for-5.16' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 dts updates for v5.16
MSM8916 gained some DT cleanup fixes. The Dragonboard 410c gains updated
firmware paths to the device specific firmware for modem and WiFi, to
allow these to be pushed to linux-next. The Longcheer L8150 gains extcon
support and the interrupt configuration for the accelerometer and
magnetometer are corrected.
MSM8998 gained descriptions for the multimedia clock controller and
iommu, as well as the GPU and its dedicated IOMMU. The QFPROM node is
updated to access the CRC corrected value space, the white LED (for
backlight) found in PMI8998 is described and GCC gains references to the
missing XO and sleep_clk reference clocks.
On top of this initial support for the Fxtec Pro1 QX1000 is added and
then the Sony Xperia XZ1, Xperia XZ1 Compact and the Xperia XZ Premium,
with USB, touchscreen, SDHCI, Bluetooth and vibrator supported.
The Xiaomi Mi 5 and Xiaomi Mi Note 2, based on the MSM8996 platform was
added, with support for frame buffer, GPU, audio, video encoder/decoder
and touchscreen.
The USB controller and PHY found in IPA6018 is described to provide USB
support. IPQ8074 gains a description of the SPMI controller.
The highlight on SC7180 is the introduction of the just released
"Homestar" device. CPU power coefficients are corrected based on
measurements, IMEM is described to ensure that remoteproc relocation
information is carried to post mortem debug tools and a few smaller
fixes are introduced.
The SC7280 gains QSPI, low speed (i2c/spi/uart), GPU, thermal zones,
modem, CPU topology and updated memory map.
On SDM845 the "Limits hardware" is described and increases the
throttling temperature of the hardware from ~70C to 95C, with up to 30%
improvement in benchmarks as result. Relying on hardware throttling and
thermal pressure, the CPU cooling devices are dropped.
The power for the second WiFi channel is properly described for the
Lenovo Yoga C630, to ensure they are both powered.
reboot-modes are defined for the PM660 PMIC, found in SDM630 and SDM660.
Initial support for the Snapdragon 690 (aka SM6350) is introduced, with
support for clocks, regulators, pinctrl, storage, thermal sensors, USB,
SMMU and CPUfreq. On top of this support for the Sony Xperia 10 III is
introduced.
* tag 'qcom-arm64-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (99 commits)
arm64: dts: qcom: sdm630-nile: Correct regulator label name
arm64: dts: qcom: sm6125: Improve indentation of multiline properties
arm64: dts: qcom: msm8916-longcheer-l8150: Use &pm8916_usbin extcon
arm64: dts: qcom: pm8916: Add pm8941-misc extcon for USB detection
arm64: dts: qcom: pm8916: Remove wrong reg-names for rtc@6000
arm64: dts: qcom: sc7280: Update Q6V5 MSS node
arm64: dts: qcom: sc7280: Add Q6V5 MSS node
arm64: dts: qcom: sc7280: Add nodes to boot modem
arm64: dts: qcom: sc7280: Add/Delete/Update reserved memory nodes
arm64: dts: qcom: sc7280: Update reserved memory map
arm64: dts: qcom: msm8998-fxtec-pro1: Add tlmm keyboard keys
arm64: dts: qcom: msm8998-fxtec-pro1: Add Goodix GT9286 touchscreen
arm64: dts: qcom: msm8998-fxtec-pro1: Add physical keyboard leds
arm64: dts: qcom: Add support for MSM8998 F(x)tec Pro1 QX1000
arm64: dts: qcom: msm8916: Fix Secondary MI2S bit clock
arm64: dts: qcom: msm8916-longcheer-l8150: Add missing sensor interrupts
arm64: dts: qcom: sc7180: Add IMEM and pil info regions
arm64: dts: qcom: pm6150l: Add missing include
arm64: dts: qcom: sm6350: Add device tree for Sony Xperia 10 III
arm64: dts: qcom: sm6350: Add apps_smmu and assign iommus prop to USB1
...
Link: https://lore.kernel.org/r/20211012231155.1036519-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:36:17 +0000 (22:36 +0200)]
Merge tag 'qcom-dts-for-5.16' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm DTS updates for v5.16
This extends the previous limited description of MSM8226 with SDHC,
UART, I2C, SCM, SMEM, RPM and basic PMIC definitions. Based on this,
initial support for the LG G Watch R smartwatch is introduced.
APQ8064 gets a couple of DT updates, one which will allow the GPU driver
to drop supporting legacy "opp tables" in the future.
DT bindings and DTS files are updated with additional compatibles, for
completeness.
* tag 'qcom-dts-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
dt-bindings: arm: qcom, add missing devices
ARM: dts: qcom: msm8974: Add xo_board reference clock to DSI0 PHY
ARM: dts: qcom: fill secondary compatible for multiple boards
ARM: dts: qcom: apq8064: adjust memory node according to specs
ARM: dts: qcom: apq8064: Convert adreno from legacy gpu-pwrlevels to opp-v2
ARM: dts: qcom: Add support for LG G Watch R
dt-bindings: arm: qcom: Document APQ8026 SoC binding
ARM: dts: qcom: Add pm8226 PMIC
ARM: dts: qcom: msm8226: Add more SoC bits
dt-bindings: arm: qcom: Document SDX65 platform and boards
Link: https://lore.kernel.org/r/20211012174310.1017857-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Tue, 19 Oct 2021 20:34:11 +0000 (22:34 +0200)]
Merge tag 'v5.15-next-dts64' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
Biggest change is, that we have now support for a reset controller inside the
mmsys. This goes inhand with changes to the driver, that you will find in the
soc pull request.
Mediatek PCI device tree binding described the root port in a wrong. The IP
actaully implements several root complex with everyone having a single root port.
We need to fix the DT in an incompatible way to describe the HW as it is. This
also fixes a problem that no IRQ bigger then 32 could be handled.
The only public available HW that is affected by this is the BananaPi R64. I'm
not aware that there is a big user base using the upstream kernel. In this
boards PCI is only used for extension cards, so I don't expect any boot problems.
- mt8173: add reset for dsi0 to mmsys
- move dt-bindings reset controller includes to correct folder
- split PCIe node to use new format for mt2712 and mt7622
- mt8183: add audio node to chromebook devices
- mt8192: add clock controller node
* tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: Add the mmsys reset bit to reset the dsi0
arm64: dts: mt8173: Add the mmsys reset bit to reset the dsi0
dt-bindings: display: mediatek: add dsi reset optional property
dt-bindings: mediatek: Add #reset-cells to mmsys system controller
arm64: dts: mediatek: Move reset controller constants into common location
arm64: dts: mediatek: Split PCIe node for MT2712 and MT7622
arm64: dts: mt8183: add kukui platform audio node
arm64: dts: mt8183: add audio node
arm64: dts: mediatek: Add mt8192 clock controllers
Link: https://lore.kernel.org/r/1a3d63a3-c020-3319-26f6-a2ec338cc42e@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Amelie Delaunay [Wed, 6 Oct 2021 09:53:55 +0000 (11:53 +0200)]
ARM: dts: stm32: use usbphyc ck_usbo_48m as USBH OHCI clock on stm32mp151
Referring to the note under USBH reset and clocks chapter of RM0436,
"In order to access USBH_OHCI registers it is necessary to activate the USB
clocks by enabling the PLL controlled by USBPHYC" (ck_usbo_48m).
The point is, when USBPHYC PLL is not enabled, OHCI register access
freezes the resume from STANDBY. It is the case when dual USBH is enabled,
instead of OTG + single USBH.
When OTG is probed, as ck_usbo_48m is USBO clock parent, then USBPHYC PLL
is enabled and OHCI register access is OK.
This patch adds ck_usbo_48m (provided by USBPHYC PLL) as clock of USBH
OHCI, thus USBPHYC PLL will be enabled and OHCI register access will be OK.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Mon, 4 Oct 2021 09:03:04 +0000 (11:03 +0200)]
ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
Fix SAI2A and SAI2B pin muxings for AV96 board on STM32MP15.
Change sai2a-4 & sai2a-5 to sai2a-2 & sai2a-2.
Change sai2a-4 & sai2a-sleep-5 to sai2b-2 & sai2b-sleep-2
Fixes:
dcf185ca8175 ("ARM: dts: stm32: Add alternate pinmux for SAI2 pins on stm32mp15")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Olivier Moysan [Fri, 24 Sep 2021 16:02:21 +0000 (18:02 +0200)]
ARM: dts: stm32: fix SAI sub nodes register range
The STM32 SAI subblocks registers offsets are in the range
0x0004 (SAIx_CR1) to 0x0020 (SAIx_DR).
The corresponding range length is 0x20 instead of 0x1c.
Change reg property accordingly.
Fixes:
5afd65c3a060 ("ARM: dts: stm32: add sai support on stm32mp157c")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Fabrice Gasnier [Tue, 21 Sep 2021 13:34:49 +0000 (15:34 +0200)]
ARM: dts: stm32: fix STUSB1600 Type-C irq level on stm32mp15xx-dkx
STUSB1600 IRQ (Alert pin) is active low (open drain). Interrupts may get
lost currently, so fix the IRQ type.
Fixes:
83686162c0eb ("ARM: dts: stm32: add STUSB1600 Type-C using I2C4 on stm32mp15xx-dkx")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Grzegorz Szymaszek [Thu, 26 Aug 2021 14:45:43 +0000 (16:45 +0200)]
ARM: dts: stm32: set the DCMI pins on stm32mp157c-odyssey
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output. The
DCMI pins used on this output are defined in the pin state definition
&pinctrl/dcmi-1, AKA &dcmi_pins_b (added in mainline commit
02814a41529a55dbfb9fbb2a3728e78e70646ea6). Set these pins as the default
pinctrl of the DCMI peripheral in the board device tree.
The pins are not used for any other purpose, so it seems safe to assume
most users will not need to override (delete) what this patch provides.
status defaults to "disabled", so the peripheral will not be
unnecessarily started. And the users who actually intend to make use of
a camera on the DVP port will have this little part of the configuration
ready.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Marek Vasut [Mon, 9 Aug 2021 12:13:24 +0000 (14:13 +0200)]
ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.
There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex, so opt for the second option.
Fixes:
76045bc457104 ("ARM: dts: stm32: Add QSPI NOR on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Alexandre Torgue [Fri, 23 Jul 2021 13:28:10 +0000 (15:28 +0200)]
ARM: dts: stm32: add initial support of stm32mp135f-dk board
Add support of stm32mp135f discovery board (part number: STM32MP135F-DK).
It embeds a STM32MP135F SOC with 512 MB of DDR3.
Several connections are available on this board:
4*USB2.0, 1*USB2.0 typeC DRD, SDcard, 2*RJ45, HDMI, Combo Wifi/BT, ...
Only SD card, uart4 (console) and watchdog IPs are enabled in this commit.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Alexandre Torgue [Fri, 23 Jul 2021 13:28:09 +0000 (15:28 +0200)]
dt-bindings: stm32: document stm32mp135f-dk board
Add new entry for stm32mp135f-dk board.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Alexandre Torgue [Fri, 23 Jul 2021 13:28:08 +0000 (15:28 +0200)]
ARM: dts: stm32: add STM32MP13 SoCs support
Add initial support of STM32MP13 family. The STM32MP13 SoC diversity is
composed by:
-STM32MP131:
-core: 1*CA7, 17*TIMERS, 5*LPTIMERS, DMA/MDMA/DMAMUX
-storage: 3*SDMCC, 1*QSPI, FMC
-com: USB (OHCI/EHCI, OTG), 5*I2C, 5*SPI/I2S, 8*U(S)ART
-audio: 2*SAI
-network: 1*ETH(GMAC)
-STM32MP133: STM32MP131 + 2*CAN, ETH2(GMAC), ADC1
-STM32MP135: STM32MP133 + DCMIPP, LTDC
A second diversity layer exists for security features:
-STM32MP13xY, "Y" gives information:
-Y = A/D means no cryp IP and no secure boot.
-Y = C/F means cryp IP + secure boot.
This commit adds basic peripheral.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Niklas Söderlund [Thu, 14 Oct 2021 21:29:06 +0000 (23:29 +0200)]
mailmap: Fix text encoding for Niklas Söderlund
There are commits that mess up the encoding of 'ö' in Söderlund, add a
correct entry to .mailmap.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211014212906.2331293-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Linus Walleij [Wed, 6 Oct 2021 22:40:08 +0000 (00:40 +0200)]
ARM: dts: ux500: Switch battery nodes to standard
This force-converts the per-device battery node into the standard
properties using "simple-battery" for the HREF machines and the
corresponding Samsung battery for the mobile phones.
This is fine to do since the battery data in the DTS files has never
been deployed or used. In commit
a1149ae97554
"ARM: ux500: Disable Power Supply and Battery Management by default"
it was turned off and has not been switched back on since. In
the meantime standardized bindings for batteries have appeared
making the old AB8500 battery bindings obsolete.
The battery node which is now in the middle of an included file
is obviously a per-device piece of information so push this down
to each board. The HREF machines all have the same battery and can
share a single node in the HREF dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Geert Uytterhoeven [Thu, 14 Oct 2021 08:36:07 +0000 (10:36 +0200)]
arm64: dts: renesas: rcar-gen3e: Add Cortex-A57 2 GHz opps
Add operating points for running the Cortex-A57 CPU cores on R-Car
H3e-2G, M3e-2G, and M3Ne-2G at 2 GHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/08a0f27f50b8ad4a78c05186190bebcfb364fe8f.1634200489.git.geert+renesas@glider.be
Biju Das [Wed, 13 Oct 2021 07:56:47 +0000 (08:56 +0100)]
arm64: dts: renesas: rzg2l-smarc-som: Enable Ethernet
Enable Ethernet{0,1} interfaces on RZ/G2L SMARC EVK.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211013075647.32231-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Wed, 13 Oct 2021 07:56:46 +0000 (08:56 +0100)]
arm64: dts: renesas: r9a07g044: Add GbEthernet nodes
Add Gigabit Ethernet{0,1} nodes to SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211013075647.32231-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Niklas Söderlund [Tue, 12 Oct 2021 18:34:31 +0000 (20:34 +0200)]
arm64: dts: renesas: Add ports node to all adv7482 nodes
The different port@ entries of the adv7482 nodes shall be encapsulated
in a ports node, add one. This change does not change how the driver
parses the DT and no driver change is needed.
The change however makes it possible to validate the source files with a
correct json-schema.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211012183431.718691-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Niklas Söderlund [Tue, 12 Oct 2021 10:00:38 +0000 (12:00 +0200)]
arm64: dts: renesas: r8a779a0: Add and connect all CSI-2, ISP and VIN nodes
The V3U have 32 VIN, 4 CSI-2 and 4 ISP nodes that interact with each
other for video capture. Add all nodes and record how they are
interconnected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20211012100038.375289-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
John Wang [Thu, 14 Oct 2021 07:27:43 +0000 (15:27 +0800)]
ARM: dts: aspeed: fp5280g2: Use the 64M layout
Use the 64M layout since the flash on the board is 64M
Signed-off-by: John Wang <wangzhiqiang02@inspur.com>
Link: https://lore.kernel.org/r/20211014072743.939293-1-wangzhiqiang02@inspur.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Arnd Bergmann [Tue, 12 Oct 2021 12:51:23 +0000 (14:51 +0200)]
Merge tag 'ti-k3-dt-for-v5.16' of git://git./linux/kernel/git/nmenon/linux into arm/dt
Devicetree changes for TI K3 platforms for v5.16 merge window:
* New Platforms:
- AM654: Siemens IOT2050 PG2 boards
- J721E: Low cost SK board
* New features:
- mmc aliases introduced
- AM64 ICSSG nodes, mcu pinctrl added
* Fixes:
- Schema fixups for pcie, thermal zones
- Fixup to include board specific property for J721e-evm and j7200-evm
- Misc fixups including cleaning up order in Makefile
* tag 'ti-k3-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux: (24 commits)
arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes
arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes
arm64: dts: ti: Add support for J721E SK
dt-bindings: arm: ti: Add compatible for J721E SK
arm64: dts: ti: iot2050: Add support for product generation 2 boards
arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
dt-bindings: arm: ti: Add bindings for Siemens IOT2050 PG2 boards
arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
arm64: dts: ti: k3-j7200-common-proc-board: Add j7200-evm compatible
arm64: dts: ti: k3-j721e-common-proc-board: Add j721e-evm compatible
dt-bindings: arm: ti: Add missing compatibles for j721e/j7200 evms
arm64: dts: ti: Makefile: Collate AM64 platforms together
arm64: dts: ti: k3-am64-main: Add ICSSG nodes
arm64: dts: ti: k3-am65: Relocate thermal-zones to SoC specific location
arm64: dts: ti: ti-k3*: Introduce aliases for mmc nodes
arm64: dts: ti: k3-am65-main: Cleanup "ranges" property in "pcie" DT node
arm64: dts: ti: j7200-main: Add *max-virtual-functions* for pcie-ep DT node
arm64: dts: ti: j7200-main: Fix "bus-range" upto 256 bus number for PCIe
...
Link: https://lore.kernel.org/r/20211012120817.beqhp4tygnf3xyi5@wireless
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chanho Park [Tue, 12 Oct 2021 00:23:14 +0000 (09:23 +0900)]
arm64: dts: exynos: add minimal support for exynosautov9 sadk board
SADK(Samsung Automotive Development Kit) is the development kit to
evaluate Exynos Auto v9 SoC. It has 16GB LPDDR4 DRAM and two
256GB Samsung UFS. This patch enables only serial console and ufs0
device.
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20211012002314.38965-4-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Chanho Park [Tue, 12 Oct 2021 00:23:13 +0000 (09:23 +0900)]
arm64: dts: exynos: add initial support for exynosautov9 SoC
Add minimal support for ExynosAuto v9 SoC[1].
- Enumarate all pinctrl nodes
- UART with exynos850 compatible
- UFS0 HCI + Phy
Like exynos850, this also uses fixed-rate clock nodes until clock driver
has been supported. The clock nodes are initialized on bootloader stage
thus we don't need to control them so far.
[1]: https://www.samsung.com/semiconductor/minisite/exynos/products/automotiveprocessor/exynos-auto-v9/
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20211012002314.38965-3-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Oskar Senft [Thu, 9 Sep 2021 00:49:20 +0000 (20:49 -0400)]
ARM: dts: aspeed: Add TYAN S7106 BMC machine
The TYAN S7106 is a server platform with an ASPEED AST2500 BMC.
Signed-off-by: Oskar Senft <osk@google.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210909004920.1634322-1-osk@google.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adriana Kobylak [Tue, 5 Oct 2021 19:22:26 +0000 (19:22 +0000)]
ARM: dts: aspeed: rainier: Add power-config-full-load gpio
Add the power-config-full-load described in:
https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md#power-config-full-load
The power-config-full-load gpio is designed to be used to specify how
many power supplies the system should have, in rainier it is 2 or 4. If
enough power supplies fail so that the system no longer has redundancy
(no longer n+1), the hardware will signal to the Onboard Chip Controller
that the system may be oversubscribed, and performance may need to be
reduced so the system can maintain it's powered on state.
Signed-off-by: Adriana Kobylak <anoo@us.ibm.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20211005192226.213539-1-anoo@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Arnd Bergmann [Mon, 11 Oct 2021 21:55:54 +0000 (23:55 +0200)]
Merge tag 'tegra-for-5.16-arm-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.16-rc1
This contains various cleanup patches to 32-bit ARM Tegra device trees
and enables USB OTG mode on the Nexus 7.
* tag 'tegra-for-5.16-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Remove useless usb-ehci compatible string
ARM: tegra: Remove unused backlight-boot-off property
ARM: tegra: nexus7: Enable USB OTG mode
ARM: tegra: Add new properties to USB PHY device-tree nodes
ARM: tegra: Update Broadcom Bluetooth device-tree nodes
ARM: tegra: acer-a500: Correct compatible of ak8975 magnetometer
Link: https://lore.kernel.org/r/20211008201132.1678814-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 21:01:29 +0000 (23:01 +0200)]
Revert "arm64: dts: Add support for Unisoc's UMS512"
The patch uses the "dt-bindings/clock/sprd,ums512-clk.h header, which
is not merged yet. This caused a build regression, and it means the
patch was not ready to get merged anyway.
This reverts commit
23410de5796cd49abb3f9b6d377822e18298e0a0.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 20:37:33 +0000 (22:37 +0200)]
Merge tag 'at91-dt-5.16' of git://git./linux/kernel/git/at91/linux into arm/dt
AT91 DT #1 for 5.16:
- Addition of a new variant in the sama5d2 family: the sama5d29 with
significant updates being CAN and Ethernet controllers;
- Add support for Exegin Q5xR5 and CalAmp LMU5000 boards which were
maintained up to this moment, separately, in OpenWrt tree;
- Two more boards gained I2C bus recovery support;
- Tse850 updated with one Ethernet fix;
- Sama7g5ek gained ADC nodes and sama5d27_wlsom1 WiFi support.
* tag 'at91-dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: at91: dts: sama5d29: Add dtsi file for sama5d29
ARM: dts: at91-sama5d2_icp.dts: Added I2C bus recovery support
ARM: dts: at91: tse850: the emac<->phy interface is rmii
ARM: dts: at91: add Exegin Q5xR5 board
dt-bindings: ARM: at91: document exegin q5xr5 board
dt-bindings: add vendor prefix for exegin
ARM: dts: at91: add CalAmp LMU5000 board
dt-bindings: ARM: at91: document CalAmp LMU5000 board
dt-bindings: add vendor prefix for calamp
ARM: dts: at91: at91sam9260: add pinctrl label
ARM: dts: at91-sama5d27_som1_ek: Added I2C bus recovery support
ARM: dts: at91: sama7g5ek: enable ADC on the board
ARM: dts: at91: sama7g5: add node for the ADC
ARM: dts: at91: sama5d27_wlsom1: add wifi device
Link: https://lore.kernel.org/r/20211011123438.16562-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 20:26:40 +0000 (22:26 +0200)]
Merge tag 'omap-for-v5.16/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.16
These changes configure devices for am335x and dra7, and fixes
various devicetree check warnings for gta04:
- Update am335x-pocketbeagle to use pinconf-single
- A series of devicetree warning fixes for omap3 and gta04
- Configure bb2d Vivante GC 2D Accelerator for dra7
* tag 'omap-for-v5.16/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra7: add entry for bb2d module
arm: dts: omap3-gta04: cleanup led node names
arm: dts: omap3-gta04a4: accelerometer irq fix
arm: dts: omap3-gta04a5: fix missing sensor supply
arm: dts: omap3-gta04: fix missing sensor supply
arm: dts: omap3-gta04: cleanup LCD definition
ARM: dts: omap3: fix cpu thermal label name
ARM: dts: am335x-pocketbeagle: switch to pinconf-single
Link: https://lore.kernel.org/r/pull-1633950030-501948@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 20:13:31 +0000 (22:13 +0200)]
Merge tag 'v5.15-next-dts32' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
mt7623: add USB nodes
mt7629: update PCIe node to new format
* tag 'v5.15-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: arm: Add MT6589 Fairphone 1
ARM: dts: mediatek: Update MT7629 PCIe node for new format
arm: dts: mt7623: add otg nodes for bpi-r2
arm: dts: mt7623: add musb device nodes
Link: https://lore.kernel.org/r/7135d46f-5fb9-b46d-96d4-3b38548fe23e@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 20:10:20 +0000 (22:10 +0200)]
Merge tag 'tegra-for-5.16-arm64-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.16-rc1
This enables additional interrupts on the Tegra194 GPIO controller for
better load balancing and/or virtualization, adds audio support on
Jetson TX2 NX, enables the NVDEC video decoder on Tegra186 and later and
enables more audio processors that are found on Tegra210 and later.
Various cleanups across the board top things off.
* tag 'tegra-for-5.16-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix pcie-ep DT nodes
arm64: tegra: Remove useless usb-ehci compatible string
arm64: tegra: Extend APE audio support on Jetson platforms
arm64: tegra: Add few AHUB devices for Tegra210 and later
arm64: tegra: Remove unused backlight-boot-off property
arm64: tegra: Add NVDEC to Tegra186/194 device trees
arm64: tegra: Add new USB PHY properties on Tegra132
arm64: tegra: Update HDA card name on Jetson TX2 NX
arm64: tegra: Audio graph sound card for Jetson TX2 NX
arm64: tegra: Add additional GPIO interrupt entries on Tegra194
Link: https://lore.kernel.org/r/20211008201132.1678814-7-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 19:55:07 +0000 (21:55 +0200)]
Merge tag 'tegra-for-5.16-dt-bindings' of git://git./linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.16-rc1
This contains the DT bindings for the NVDEC hardware video decoder found
on Tegra210 and later chips as well as a node name fix for the examples
in the Tegra194 PCIe controller (endpoint mode) DT bindings.
* tag 'tegra-for-5.16-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: PCI: tegra194: Fix PCIe endpoint node names
dt-bindings: Add YAML bindings for NVDEC
Link: https://lore.kernel.org/r/20211008201132.1678814-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chunyan Zhang [Fri, 8 Oct 2021 03:45:33 +0000 (11:45 +0800)]
arm64: dts: Add support for Unisoc's UMS512
Add basic DT to support Unisoc's UMS512, with this patch,
the board ums512-1h10 can run into console.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20211008034533.343167-3-zhang.lyra@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chunyan Zhang [Fri, 8 Oct 2021 03:45:32 +0000 (11:45 +0800)]
dt-bindings: arm: Add bindings for Unisoc's UMS512
Added bindings for Unisoc's ums512-1h10 board and ums512 SoC.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211008034533.343167-2-zhang.lyra@gmail.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 15:12:10 +0000 (17:12 +0200)]
Merge tag 'amlogic-arm64-dt-for-v5.16' of git://git./linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM64 DT changes for v5.16:
- New Boards (with bindings):
- Radxa Zero
- Jethub D1 & H1 home automation controllers
- Misc Changes:
- add Ethernet PHY reset line for ODROID-C4/HC4
- add audio playback nodes to rbox-pro
- Fix the pwm regulator supply properties
- meson-g12b-odroid-n2: add missing 5v regulator gpio
* tag 'amlogic-arm64-dt-for-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: meson-g12b-odroid-n2: add 5v regulator gpio
arm64: dts: meson-sm1: Fix the pwm regulator supply properties
arm64: dts: meson-g12b: Fix the pwm regulator supply properties
arm64: dts: meson-g12a: Fix the pwm regulator supply properties
arm64: dts: meson: add audio playback to rbox-pro
arm64: dts: meson-axg: add support for JetHub D1
arm64: dts: meson-gxl: add support for JetHub H1
dt-bindings: vendor-prefixes: add jethome prefix
dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
arm64: dts: amlogic: add support for Radxa Zero
dt-bindings: arm: amlogic: add support for Radxa Zero
arm64: dts: meson: sm1: add Ethernet PHY reset line for ODROID-C4/HC4
Link: https://lore.kernel.org/r/cc0a3af0-b1b1-dbe1-f553-cf58a1c63d0b@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 11 Oct 2021 15:10:13 +0000 (17:10 +0200)]
Merge tag 'zynqmp-dt-for-v5.16-v2' of https://github.com/Xilinx/linux-xlnx into arm/dt
arm64: dts: ZynqMP DT changes for v5.16-v2
- Add support for Kria SOM board
* tag 'zynqmp-dt-for-v5.16-v2' of https://github.com/Xilinx/linux-xlnx:
arm64: zynqmp: Add support for Xilinx Kria SOM board
Link: https://lore.kernel.org/r/9815867c-ffbb-fc9d-64b9-badee5e2862b@xilinx.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Biju Das [Sun, 10 Oct 2021 14:25:20 +0000 (15:25 +0100)]
arm64: dts: renesas: rzg2l-smarc: Enable microSD on SMARC platform
This patch enables microSD card slot connected to SDHI1 on RZ/G2L SMARC
platform.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211010142520.21976-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Biju Das [Sun, 10 Oct 2021 14:25:19 +0000 (15:25 +0100)]
arm64: dts: renesas: rzg2l-smarc-som: Enable eMMC on SMARC platform
RZ/G2L SoM has both 64 GB eMMC and microSD connected to SDHI0.
Both these interfaces are mutually exclusive and the SD0 device
selection is based on the XOR between GPIO_SD0_DEV_SEL and SW1[2]
switch position.
This patch sets GPIO_SD0_DEV_SEL to high in DT. Use the below switch
setting logic for device selection between eMMC and microSD slot
connected to SDHI0.
Set SW1[2] to position 2/OFF for selecting eMMC
Set SW1[2] to position 3/ON for selecting microSD
This patch enables eMMC on RZ/G2L SMARC platform by default.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211010142520.21976-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Florian Fainelli [Fri, 8 Oct 2021 22:29:25 +0000 (15:29 -0700)]
Merge tag 'tags/bcm2835-dt-next-2021-10-06' into devicetree/next
Stefan Wahren adds devicetree support for the Raspbery Pi Compute Module
4 and its IO board
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Luca Weiss [Tue, 5 Oct 2021 20:28:30 +0000 (22:28 +0200)]
dt-bindings: arm: Add MT6589 Fairphone 1
Add the compatible for Fairphone 1 smartphone with MT6589 SoC.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20211005202833.96526-1-luca@z3ntu.xyz
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Biju Das [Thu, 7 Oct 2021 15:54:49 +0000 (16:54 +0100)]
arm64: dts: renesas: r9a07g044: Add SDHI nodes
Add SDHI{0, 1} nodes to RZ/G2L SoC DTSI.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211007155451.10654-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Wed, 6 Oct 2021 08:58:36 +0000 (10:58 +0200)]
arm64: dts: renesas: falcon-cpu: Add SPI flash via RPC
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211006085836.42155-5-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Duc Nguyen [Wed, 6 Oct 2021 08:58:35 +0000 (10:58 +0200)]
arm64: dts: renesas: r8a779a0: Add RPC node
Add device node for RPC on R8A779A0 SoC.
Signed-off-by: Duc Nguyen <duc.nguyen.ub@renesas.com>
[wsa: rebased]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211006085836.42155-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Lad Prabhakar [Tue, 28 Sep 2021 15:58:52 +0000 (16:58 +0100)]
arm64: dts: renesas: r9a07g044: Add SPI Multi I/O Bus controller node
Add SPI Multi I/O Bus controller node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210928155852.32569-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enric Balletbo i Serra [Thu, 30 Sep 2021 08:31:48 +0000 (10:31 +0200)]
arm64: dts: mt8183: Add the mmsys reset bit to reset the dsi0
Reset the DSI hardware is needed to prevent different settings between
the bootloader and the kernel.
While here, also remove the undocumented and also not used
'mediatek,syscon-dsi' property.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210930103105.v4.5.I933f1532d7a1b2910843a9644c86a7d94a4b44e1@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Thu, 30 Sep 2021 08:31:47 +0000 (10:31 +0200)]
arm64: dts: mt8173: Add the mmsys reset bit to reset the dsi0
Reset the DSI hardware is needed to prevent different settings between
the bootloader and the kernel.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210930103105.v4.4.I7bd7d9a8da5e2894711b700a1127e6902a2b2f1d@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Thu, 30 Sep 2021 08:31:46 +0000 (10:31 +0200)]
dt-bindings: display: mediatek: add dsi reset optional property
Update device tree binding documentation for the dsi to add the optional
property to reset the dsi controller.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210930103105.v4.3.Ifec72a83f224b62f24cfc967edfe78c5d276b2e3@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Thu, 30 Sep 2021 08:31:45 +0000 (10:31 +0200)]
dt-bindings: mediatek: Add #reset-cells to mmsys system controller
The mmsys system controller exposes a set of memory client resets and
needs to specify the #reset-cells property in order to advertise the
number of cells needed to describe each of the resets.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210930103105.v4.2.I3f7f1c9a8e46be07d1757ddf4e0097535f3a7d41@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enric Balletbo i Serra [Thu, 30 Sep 2021 08:31:44 +0000 (10:31 +0200)]
arm64: dts: mediatek: Move reset controller constants into common location
The DT binding includes for reset controllers are located in
include/dt-bindings/reset/. Move the Mediatek reset constants in there.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20210930103105.v4.1.I514d9aafff3a062f751b37d3fea7402f67595b86@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Joel Stanley [Thu, 23 Sep 2021 07:46:06 +0000 (17:16 +0930)]
ARM: dts: aspeed: p10bmc: Define secure boot gpio
Input pin that indicates that the BMC is configured to boot with security
protections enforced.
Pulled up by default (secure). Placing the jumper will pull the pin down
(bypass security).
When in the secure boot state, it makes the EEPROM at 0x50 on bus 14
read only.
Link: https://lore.kernel.org/r/20210923074606.283393-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Quan Nguyen [Fri, 17 Sep 2021 08:29:45 +0000 (15:29 +0700)]
ARM: dts: aspeed: mtjade: Add some gpios
Add S0_SCP_AUTH_FAIL, S1_SCP_AUTH_FAIL gpios to indicates firmware
authentication fail on each socket.
Add gpio RTC_BAT_SEN_EN to enable RTC battery adc sensor.
Add BMC_I2C4_O_EN gpio to go high at boot to enable access to I2C4 bus.
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Signed-off-by: Thang Nguyen <thang@os.amperecomputing.com>
Link: https://lore.kernel.org/r/20210917082945.19111-1-quan@os.amperecomputing.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Mauro Carvalho Chehab [Sun, 18 Jul 2021 11:40:52 +0000 (13:40 +0200)]
dt-bindings: PCI: tegra194: Fix PCIe endpoint node names
As defined by Documentation/devicetree/bindings/pci/pci-ep.yaml,
PCIe endpoints match this pattern:
properties:
$nodename:
pattern: "^pcie-ep@"
Change the existing ones in the DT bindings examples to avoid warnings
during DT bindings validation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Mauro Carvalho Chehab [Sun, 18 Jul 2021 11:40:52 +0000 (13:40 +0200)]
arm64: tegra: Fix pcie-ep DT nodes
As defined by Documentation/devicetree/bindings/pci/pci-ep.yaml,
PCIe endpoints match this pattern:
properties:
$nodename:
pattern: "^pcie-ep@"
Change the existing ones in order to avoid those warnings:
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dt.yaml: pcie_ep@
14160000: $nodename:0: 'pcie_ep@
14160000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dt.yaml: pcie_ep@
14180000: $nodename:0: 'pcie_ep@
14180000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dt.yaml: pcie_ep@
141a0000: $nodename:0: 'pcie_ep@
141a0000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dt.yaml: pcie_ep@
14160000: $nodename:0: 'pcie_ep@
14160000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dt.yaml: pcie_ep@
14180000: $nodename:0: 'pcie_ep@
14180000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dt.yaml: pcie_ep@
141a0000: $nodename:0: 'pcie_ep@
141a0000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dt.yaml: pcie_ep@
14160000: $nodename:0: 'pcie_ep@
14160000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dt.yaml: pcie_ep@
14180000: $nodename:0: 'pcie_ep@
14180000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dt.yaml: pcie_ep@
141a0000: $nodename:0: 'pcie_ep@
141a0000' does not match '^pcie-ep@'
From schema: Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Mon, 21 Jun 2021 14:13:27 +0000 (16:13 +0200)]
arm64: tegra: Remove useless usb-ehci compatible string
There's no such thing as a generic USB EHCI controller. The EHCI
controllers found on Tegra SoCs are instantiations that need Tegra-
specific glue to work properly, so drop the generic compatible string
and keep only the Tegra-specific ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Mon, 21 Jun 2021 14:13:26 +0000 (16:13 +0200)]
ARM: tegra: Remove useless usb-ehci compatible string
There's no such thing as a generic USB EHCI controller. The EHCI
controllers found on Tegra SoCs are instantiations that need Tegra-
specific glue to work properly, so drop the generic compatible string
and keep only the Tegra-specific ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sameer Pujar [Mon, 13 Sep 2021 16:42:21 +0000 (22:12 +0530)]
arm64: tegra: Extend APE audio support on Jetson platforms
Extend APE audio support by adding more audio components such as SFC,
MVC, AMX, ADX and Mixer. These components can be plugged into an audio
path and required processing can be done. ASoC audio-graph based sound
driver is used to facilitate this and thus extend sound bindings as
well.
The components in the path may require different PCM parameters (such
as sample rate, channels or sample size). Depending on the pre-defined
audio paths, these can be statically configured with "convert-xxx" DT
properties in endpoint subnode. The support for the rate and channel
conversion is already available in generic audio-graph driver. Sample
size conversion support can be added based on the need in future.
The support is extended for following platforms:
* Jertson TX1
* Jetson Nano
* Jetson TX2
* Jetson AGX Xavier
* Jetson Xavier NX
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sameer Pujar [Mon, 13 Sep 2021 16:42:20 +0000 (22:12 +0530)]
arm64: tegra: Add few AHUB devices for Tegra210 and later
Add DT nodes for following AHUB devices:
* SFC (Sampling Frequency Converter)
* MVC (Master Volume Control)
* AMX (Audio Multiplexer)
* ADX (Audio Demultiplexer)
* Mixer
Above devices are added for Tegra210, Tegra186 and Tegra194 generations
of Tegra SoC.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
David Heidelberg [Sun, 19 Sep 2021 15:27:20 +0000 (17:27 +0200)]
arm64: tegra: Remove unused backlight-boot-off property
The backlight-boot-off property was proposed as a patch, but ended not
being accepted since different solution was already in the place:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/
1406806970-12561-1-git-send-email-thierry.reding@gmail.com/#
21327479
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Thierry Reding <treding@nvidia.com>
David Heidelberg [Sun, 19 Sep 2021 15:27:20 +0000 (17:27 +0200)]
ARM: tegra: Remove unused backlight-boot-off property
The backlight-boot-off property was proposed as a patch, but ended not
being accepted since different solution was already in the place:
https://patchwork.kernel.org/project/linux-arm-kernel/patch/
1406806970-12561-1-git-send-email-thierry.reding@gmail.com/#
21327479
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Mikko Perttunen [Thu, 16 Sep 2021 14:55:16 +0000 (17:55 +0300)]
arm64: tegra: Add NVDEC to Tegra186/194 device trees
Add a device tree node for NVDEC on Tegra186, and
device tree nodes for NVDEC and NVDEC1 on Tegra194.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Mikko Perttunen [Thu, 16 Sep 2021 14:55:15 +0000 (17:55 +0300)]
dt-bindings: Add YAML bindings for NVDEC
Add YAML device tree bindings for NVDEC, now in a more appropriate
place compared to the old textual Host1x bindings.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Stefan Wahren [Sat, 7 Aug 2021 11:06:41 +0000 (13:06 +0200)]
arm64: dts: broadcom: Add reference to RPi CM4 IO Board
This adds a reference to the dts of the Raspberry Pi Compute Module 4
IO Board, so we don't need to maintain the content in arm64.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-11-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Stefan Wahren [Sat, 7 Aug 2021 11:06:40 +0000 (13:06 +0200)]
ARM: dts: Add Raspberry Pi Compute Module 4 IO Board
This adds the matching carrier for Raspberry Pi Compute Module 4.
Instead of xHCI USB host controller there is just a USB 2.0 interface
connected to the DWC2 controller from the BCM2711. As a result
there is a free PCIe Gen 2 socket. Also there are 2 full-size HDMI 2.0
connectors.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-10-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Stefan Wahren [Sat, 7 Aug 2021 11:06:39 +0000 (13:06 +0200)]
ARM: dts: Add Raspberry Pi Compute Module 4
The Raspberry Pi Compute Module 4 (CM4) are SoMs which contain the
following:
* BCM2711 quad core processor
* up to 8 GB RAM
* up to 32 GB eMMC
* a GPIO expander
* Gigabit PHY BCM54210PE
* Wifi/BT module with internal and external antenna
The eMMC and the Wifi/BT module are optional.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-9-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Stefan Wahren [Sat, 7 Aug 2021 11:06:38 +0000 (13:06 +0200)]
dt-bindings: arm: bcm2835: Add Raspberry Pi Compute Module 4
Add the Raspberry Pi Compute Module 4 to DT schema.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1628334401-6577-8-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Stefan Wahren [Sat, 7 Aug 2021 11:06:37 +0000 (13:06 +0200)]
ARM: dts: bcm283x-rpi: Move Wifi/BT into separate dtsi
A Wifi/BT chip is quite common for the Raspberry Pi boards. So move those
definitions into a separate dtsi in order to avoid copy & paste. This
change was inspired by a vendor tree patch from Phil Elwell.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-7-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Stefan Wahren [Sat, 7 Aug 2021 11:06:34 +0000 (13:06 +0200)]
dt-bindings: display: bcm2835: add optional property power-domains
The Raspberry Pi boards with BCM283x needs control of the power domains
to get display components running. DT schema warns us that it's used, but not
documented as a optional property:
hdmi@
7e902000: 'power-domains' does not match any of the regexes: ...
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1628334401-6577-4-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Gowtham Tammana [Tue, 21 Sep 2021 07:18:07 +0000 (09:18 +0200)]
ARM: dts: dra7: add entry for bb2d module
BB2D is a Vivante GC 2D Accelerator.
This adds the node to the dts file within a target module node.
Crossbar index number is used for interrupt mapping.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Fri, 1 Oct 2021 07:34:16 +0000 (09:34 +0200)]
arm: dts: omap3-gta04: cleanup led node names
Change led node names to match schema.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Fri, 1 Oct 2021 07:34:15 +0000 (09:34 +0200)]
arm: dts: omap3-gta04a4: accelerometer irq fix
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes:
ee327111953b ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Fri, 1 Oct 2021 07:34:14 +0000 (09:34 +0200)]
arm: dts: omap3-gta04a5: fix missing sensor supply
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Fri, 1 Oct 2021 07:34:13 +0000 (09:34 +0200)]
arm: dts: omap3-gta04: fix missing sensor supply
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Fri, 1 Oct 2021 07:34:12 +0000 (09:34 +0200)]
arm: dts: omap3-gta04: cleanup LCD definition
Replace depreciated nodenames, fix label name to match scheme.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Andreas Kemnade [Fri, 1 Oct 2021 13:59:08 +0000 (15:59 +0200)]
ARM: dts: omap3: fix cpu thermal label name
Hyphens should be used in label names. make dtbs_check complains
about that since it does not match the corresponding pattern
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Drew Fustini [Wed, 25 Aug 2021 20:25:19 +0000 (13:25 -0700)]
ARM: dts: am335x-pocketbeagle: switch to pinconf-single
Switch the compatible for the am33xx_pinmux pin controller node from
pinctrl-single to pinconf-single. The only change between these two
compatibles is that PCS_HAS_PINCONF will be true. This then allows
pinconf properties to be utilized.
The purpose of this change is to allow the PocketBeagle to use:
pinctrl-single,bias-pullup
pinctrl-single,bias-pulldown
This dts already defines these properites for gpio pins in the default
pinctrl state but it has no effect unless PCS_HAS_PINCONF is set.
The bias properties can then be modified on the corresponding gpio lines
through the gpiod uapi. The mapping between the pins and gpio lines is
defined by gpio-ranges under the gpio controller nodes in am33xx-l4.dtsi
Signed-off-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sinthu Raja [Wed, 29 Sep 2021 08:13:33 +0000 (13:43 +0530)]
arm64: dts: ti: k3-j721e-sk: Add DDR carveout memory nodes
Two carveout reserved memory nodes each have been added for each of the
other remote processors devices within the MAIN domain on the TI J721E
SK boards. These nodes are assigned to the respective rproc device nodes
as well. The first region will be used as the DMA pool for the rproc
devices, and the second region will furnish the static carveout regions
for the firmware memory.
An additional reserved memory node is also added to reserve a portion of
the DDR memory to be used for performing inter-processor communication
between all the remote processors running RTOS or baremetal firmwares.
8 MB of memory is reserved for this purpose, and this accounts for all
the vrings and vring buffers between all the possible pairs of remote
processors.
The current carveout addresses and sizes are defined statically for each
rproc device. The R5F processors do not have an MMU, and as such require
the exact memory used by the firmwares to be set-aside. The C71x DSP
processor does support a MMU called CMMU, but is not currently supported
and as such requires the exact memory used by the firmware to be
set-aside. The firmware images do not require any RSC_CARVEOUT entries
in their resource tables to allocate the memory for firmware memory
segments
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-5-sinthu.raja@ti.com
Sinthu Raja [Wed, 29 Sep 2021 08:13:32 +0000 (13:43 +0530)]
arm64: dts: ti: k3-j721e-sk: Add IPC sub-mailbox nodes
Add the sub-mailbox nodes that are used to communicate between MPU and
various remote processors present in the J721E SoCs to the J721E EAIK
board. These include the R5F remote processors in the dual-R5F cluster
(MCU_R5FSS0) in the MCU domain and the two dual-R5F clusters
(MAIN_R5FSS0 & MAIN_R5FSS1) in the MAIN domain; the two C66x DSP remote
processors and the single C71x DSP remote processor in the MAIN domain.
These sub-mailbox nodes utilize the System Mailbox clusters 0 through 4.
All the remaining mailbox clusters are currently not used on A72 core,
and are hence disabled.
The sub-mailbox nodes added match the hard-coded mailbox configuration
used within the TI RTOS IPC software packages. The R5F processor
sub-systems are assumed to be running in Split mode, so a sub-mailbox
node is used by each of the R5F cores. Only the sub-mailbox node for
the first R5F core in each cluster is used in case of a Lockstep mode
for that R5F cluster.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-4-sinthu.raja@ti.com
Sinthu Raja [Wed, 29 Sep 2021 08:13:31 +0000 (13:43 +0530)]
arm64: dts: ti: Add support for J721E SK
J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.
J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
Add basic support for J721E-SK.
[1] https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-3-sinthu.raja@ti.com
Sinthu Raja [Wed, 29 Sep 2021 08:13:30 +0000 (13:43 +0530)]
dt-bindings: arm: ti: Add compatible for J721E SK
J721E Starter Kit (SK)[1] is a low cost, small form factor board
designed for TI’s J721E SoC. Add j721e-sk into compatible enum.
[1]https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210929081333.26454-2-sinthu.raja@ti.com
Jan Kiszka [Sun, 26 Sep 2021 12:05:17 +0000 (14:05 +0200)]
arm64: dts: ti: iot2050: Add support for product generation 2 boards
This adds the devices trees for IOT2050 Product Generation 2 (PG2)
boards. We have Basic and an Advanced variants again, differing in
number of cores, RAM size, availability of eMMC and further details.
The major difference to PG1 is the used silicon revision (SR2.x on
PG2).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/cc868da8264324bde2c87d0c01d4763e3678c706.1632657917.git.jan.kiszka@web.de
Jan Kiszka [Sun, 26 Sep 2021 12:05:16 +0000 (14:05 +0200)]
arm64: dts: ti: iot2050: Prepare for adding 2nd-generation boards
The current IOT2050 devices are Product Generation 1 (PG1), using SR1.0
AM65x silicon. Upcoming PG2 devices will use SR2.x SoCs and will
therefore need separate device trees. Prepare for that by factoring out
common bits that will be shared across both generations.
At this chance, drop a link to the product homepage to in the top-level
dts files. Also fix a typo in my email address in some headers.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/31fece05f9728a852c0632985c4fa537cced4ece.1632657917.git.jan.kiszka@web.de
Jan Kiszka [Sun, 26 Sep 2021 12:05:15 +0000 (14:05 +0200)]
dt-bindings: arm: ti: Add bindings for Siemens IOT2050 PG2 boards
Product Generation 2 (PG2) boards are based on SR2.x SoCs and will be
released soon.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/5d99e69ff1e2fb78f51f03c351eff1fe1f6c3a71.1632657917.git.jan.kiszka@web.de
Jan Kiszka [Sun, 26 Sep 2021 12:05:14 +0000 (14:05 +0200)]
arm64: dts: ti: iot2050: Add/enabled mailboxes and carve-outs for R5F cores
Analogously to the am654-base-board, configure the mailboxes for the two
R5F cores, add them and the already existing memory carve-outs to the
related MCU nodes. Allows to load applications under Linux onto the
cores, e.g. the RTI watchdog firmware.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/1776f8be19b39a938d9248fcfc5332b753783c3e.1632657917.git.jan.kiszka@web.de
Jan Kiszka [Sun, 26 Sep 2021 12:05:13 +0000 (14:05 +0200)]
arm64: dts: ti: iot2050: Disable SR2.0-only PRUs
The IOT2050 devices described so far are using SR1.0 silicon, thus do
not have the additional PRUs of the ICSSG of the SR2.0. Disable them.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/189a91866fb1af02e4fd2345dc56774aa069d5ba.1632657917.git.jan.kiszka@web.de
Jan Kiszka [Sun, 26 Sep 2021 12:05:12 +0000 (14:05 +0200)]
arm64: dts: ti: iot2050: Flip mmc device ordering on Advanced devices
This ensures that the SD card will remain mmc0 across Basic and Advanced
devices, also avoiding surprises for users coming from the downstream
kernels.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/fe20d6346f119a28e47d129b616682001299cf0e.1632657917.git.jan.kiszka@web.de
Nishanth Menon [Sat, 25 Sep 2021 20:14:30 +0000 (15:14 -0500)]
arm64: dts: ti: k3-j7200-common-proc-board: Add j7200-evm compatible
Add j7200-evm compatible to the board to allow the board to distinguish
itself from other platforms that may be added in the future.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210925201430.11678-5-nm@ti.com
Nishanth Menon [Sat, 25 Sep 2021 20:14:29 +0000 (15:14 -0500)]
arm64: dts: ti: k3-j721e-common-proc-board: Add j721e-evm compatible
Add j721e-evm compatible to the board to allow the board to distinguish
itself from other platforms that are pending to be added.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210925201430.11678-4-nm@ti.com
Nishanth Menon [Sat, 25 Sep 2021 20:14:27 +0000 (15:14 -0500)]
dt-bindings: arm: ti: Add missing compatibles for j721e/j7200 evms
Add compatibles for j721e and j7200 evms to allow for newer platforms
to distinguish themselves.
While doing this, maintain support for older style of description where
the board compatibility was not required.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210925201430.11678-2-nm@ti.com
Nishanth Menon [Wed, 15 Sep 2021 12:14:42 +0000 (07:14 -0500)]
arm64: dts: ti: Makefile: Collate AM64 platforms together
Make sure that the platforms are grouped together per SoC. This helps
keep the Makefile readable as newer platforms get added to the list.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Link: https://lore.kernel.org/r/20210915121442.27112-1-nm@ti.com
Suman Anna [Sun, 19 Sep 2021 20:29:35 +0000 (15:29 -0500)]
arm64: dts: ti: k3-am64-main: Add ICSSG nodes
Add the DT nodes for the ICSSG0 and ICSSG1 processor subsystems that are
present on the K3 AM64x SoCs. The two ICSSGs are identical to each other
for the most part, with some of the peripheral pins from ICSSG1 not pinned
out. Each ICSSG instance is represented by a PRUSS subsystem node and other
child nodes.
The nodes are all added and enabled in the common k3-am64-main.dtsi
file by default. The MDIO nodes need pinctrl lines, and so should be
enabled only on boards where they are actually wired and pinned out
for ICSSG Ethernet. Any new board dts file should disable these if
they are not sure. These are disabled in the existing AM64x board dts
files to begin with.
The ICSSGs on K3 AM64x SoCs are very similar to the versions of the ICSSG
on K3 J721E and AM65x SR2.0 SoCs. The IRAM and BroadSize RAM sizes are all
identical to those on J721E SoCs. All The ICSSG host interrupts intended
towards the main Arm core are also shared with other processors on the SoC,
and can be partitioned as per system integration needs.
The ICSSG subsystem node contains the entire address space. The various
sub-modules of the ICSSG are represented as individual child nodes (so
platform devices themselves) of the PRUSS subsystem node. These include:
- two Programmable Real-Time Units (PRUs)
- two auxiliary PRU cores called RTUs
- two Transmit Programmable Real-Time Units (Tx_PRUs)
- Interrupt controller (INTC)
- a 'memories' node containing all the ICSSG level Data RAMs
- Real Time Media Independent Interface controller (MII_RT)
- Gigabit capable MII_G_RT
- ICSSG CFG sub-module providing two internal clock muxes, with the
default clock parents also assigned using the assigned-clock-parents
property.
The default names for the firmware images for each PRU, RTU and Tx_PRU
cores are defined as follows using the 'firmware-name' property (these
can be adjusted either in derivative board dts files or through sysfs at
runtime if required):
ICSSG0 PRU0 Core : am64x-pru0_0-fw ; PRU1 Core : am64x-pru0_1-fw
ICSSG0 RTU0 Core : am64x-rtu0_0-fw ; RTU1 Core : am64x-rtu0_1-fw
ICSSG0 Tx_PRU0 Core : am64x-txpru0_0-fw ; Tx_PRU1 Core : am64x-txpru0_1-fw
ICSSG1 PRU0 Core : am64x-pru1_0-fw ; PRU1 Core : am64x-pru1_1-fw
ICSSG1 RTU0 Core : am64x-rtu1_0-fw ; RTU1 Core : am64x-rtu1_1-fw
ICSSG1 Tx_PRU0 Core : am64x-txpru1_0-fw ; Tx_PRU1 Core : am64x-txpru1_1-fw
Note:
1. The ICSSG INTC on AM64x SoCs share all the host interrupts with other
processors, so use the 'ti,irqs-reserved' property in derivative board
dts files _if_ any of them should not be handled by the host OS.
2. There are few more sub-modules like the Industrial Ethernet Peripherals
(IEPs), eCAP, PWM, UART that do not have bindings and so will be added
in the future.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210919202935.15604-1-s-anna@ti.com
Arnd Bergmann [Tue, 5 Oct 2021 14:31:01 +0000 (16:31 +0200)]
Merge tag 'renesas-dt-bindings-for-v5.16-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.16
- Document support for the new R-Car H3e, M3e, M3Ne(-2G), D3e, E3e, and
H3Ne SoCs and boards.
* tag 'renesas-dt-bindings-for-v5.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Document more R-Car Gen3e Socs and boards
Link: https://lore.kernel.org/r/cover.1633081158.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
projects / platform / kernel / linux-rpi.git / log