Martin Willi [Wed, 22 Aug 2018 07:39:52 +0000 (09:39 +0200)]
ath10k: schedule hardware restart if WMI command times out
[ Upstream commit
a9911937e7d332761e8c4fcbc7ba0426bdc3956f ]
When running in AP mode, ath10k sometimes suffers from TX credit
starvation. The issue is hard to reproduce and shows up once in a
few days, but has been repeatedly seen with QCA9882 and a large
range of firmwares, including 10.2.4.70.67.
Once the module is in this state, TX credits are never replenished,
which results in "SWBA overrun" errors, as no beacons can be sent.
Even worse, WMI commands run in a timeout while holding the conf
mutex for three seconds each, making any further operations slow
and the whole system unresponsive.
The firmware/driver never recovers from that state automatically,
and triggering TX flush or warm restarts won't work over WMI. So
issue a hardware restart if a WMI command times out due to missing
TX credits. This implies a connectivity outage of about 1.4s in AP
mode, but brings back the interface and the whole system to a usable
state. WMI command timeouts have not been seen in absent of this
specific issue, so taking such drastic actions seems legitimate.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Basierski [Thu, 9 Aug 2018 09:45:40 +0000 (11:45 +0200)]
ixgbevf: VF2VF TCP RSS
[ Upstream commit
7fb94bd58dd6650a0158e68d414e185077d8b57a ]
While VF2VF with RSS communication, RSS Type were wrongly recognized
and RSS hash was not calculated as it should be. Packets was
distributed on various queues by accident.
This commit fixes that behaviour and causes proper RSS Type recognition.
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sara Sharon [Tue, 1 May 2018 11:54:22 +0000 (14:54 +0300)]
iwlwifi: mvm: fix BAR seq ctrl reporting
[ Upstream commit
941ab4eb66c10bc5c7234e83a7a858b2806ed151 ]
There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.
However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.
This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Lunn [Sun, 2 Sep 2018 16:13:14 +0000 (18:13 +0200)]
net: dsa: mv88e6xxx: Fix writing to a PHY page.
[ Upstream commit
c309b158090d788e96ee597444965cb79b040484 ]
After changing to the needed page, actually write the value to the
register!
Fixes:
09cb7dfd3f14 ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson [Thu, 30 Aug 2018 15:23:38 +0000 (08:23 -0700)]
pinctrl: ssbi-gpio: Fix pm8xxx_pin_config_get() to be compliant
[ Upstream commit
b432414b996d32a1bd9afe2bd595bd5729c1477f ]
If you look at "pinconf-groups" in debugfs for ssbi-gpio you'll notice
it looks like nonsense.
The problem is fairly well described in commit
1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit
05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-gpio has the same
problem. Let's fix it there too.
Fixes:
b4c45fe974bc ("pinctrl: qcom: ssbi: Family A gpio & mpp drivers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Douglas Anderson [Thu, 30 Aug 2018 15:23:39 +0000 (08:23 -0700)]
pinctrl: spmi-mpp: Fix pmic_mpp_config_get() to be compliant
[ Upstream commit
0d5b476f8f57fcb06c45fe27681ac47254f63fd2 ]
If you look at "pinconf-groups" in debugfs for ssbi-mpp you'll notice
it looks like nonsense.
The problem is fairly well described in commit
1cf86bc21257 ("pinctrl:
qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant") and
commit
05e0c828955c ("pinctrl: msm: Fix msm_config_group_get() to be
compliant"), but it was pointed out that ssbi-mpp has the same
problem. Let's fix it there too.
NOTE: in case it's helpful to someone reading this, the way to tell
whether to do the -EINVAL or not is to look at the PCONFDUMP for a
given attribute. If the last element (has_arg) is false then you need
to do the -EINVAL trick.
ALSO NOTE: it seems unlikely that the values returned when we try to
get PIN_CONFIG_BIAS_PULL_UP will actually be printed since "has_arg"
is false for that one, but I guess it's still fine to return different
values so I kept doing that. It seems like another driver (ssbi-gpio)
uses a custom attribute (PM8XXX_QCOM_PULL_UP_STRENGTH) for something
similar so maybe a future change should do that here too.
Fixes:
cfb24f6ebd38 ("pinctrl: Qualcomm SPMI PMIC MPP pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Boyd [Fri, 31 Aug 2018 00:58:52 +0000 (17:58 -0700)]
pinctrl: qcom: spmi-mpp: Fix drive strength setting
[ Upstream commit
89c68b102f13f123aaef22b292526d6b92501334 ]
It looks like we parse the drive strength setting here, but never
actually write it into the hardware to update it. Parse the setting and
then write it at the end of the pinconf setting function so that it
actually sticks in the hardware.
Fixes:
0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Mon, 27 Aug 2018 07:45:44 +0000 (09:45 +0200)]
ACPI / LPSS: Add alternative ACPI HIDs for Cherry Trail DMA controllers
[ Upstream commit
240714061c58e6b1abfb3322398a7634151c06cb ]
Bay and Cherry Trail DSTDs represent a different set of devices depending
on which OS the device think it is booting. One set of decices for Windows
and another set of devices for Android which targets the Android-x86 Linux
kernel fork (which e.g. used to have its own display driver instead of
using the i915 driver).
Which set of devices we are actually going to get is out of our control,
this is controlled by the ACPI OSID variable, which gets either set through
an EFI setup option, or sometimes is autodetected. So we need to support
both.
This commit adds support for the
80862286 and
808622C0 ACPI HIDs which we
get for the first resp. second DMA controller on Cherry Trail devices when
OSID is set to Android.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Tue, 11 Sep 2018 10:20:40 +0000 (19:20 +0900)]
kprobes: Return error if we fail to reuse kprobe instead of BUG_ON()
[ Upstream commit
819319fc93461c07b9cdb3064f154bd8cfd48172 ]
Make reuse_unused_kprobe() to return error code if
it fails to reuse unused kprobe for optprobe instead
of calling BUG_ON().
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: David S . Miller <davem@davemloft.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Naveen N . Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/153666124040.21306.14150398706331307654.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Valente [Fri, 14 Sep 2018 14:23:07 +0000 (16:23 +0200)]
block, bfq: correctly charge and reset entity service in all cases
[ Upstream commit
cbeb869a3d1110450186b738199963c5e68c2a71 ]
BFQ schedules entities (which represent either per-process queues or
groups of queues) as a function of their timestamps. In particular, as
a function of their (virtual) finish times. The finish time of an
entity is computed as a function of the budget assigned to the entity,
assuming, tentatively, that the entity, once in service, will receive
an amount of service equal to its budget. Then, when the entity is
expired because it finishes to be served, this finish time is updated
as a function of the actual service received by the entity. This
allows the entity to be correctly charged with only the service
received, and then to be correctly re-scheduled.
Yet an entity may receive service also while not being the entity in
service (in the scheduling environment of its parent entity), for
several reasons. If the entity remains with no backlog while receiving
this 'unofficial' service, then it is expired. Also on such an
expiration, the finish time of the entity should be updated to account
for only the service actually received by the entity. Unfortunately,
such an update is not performed for an entity expiring without being
the entity in service.
In a similar vein, the service counter of the entity in service is
reset when the entity is expired, to be ready to be used for next
service cycle. This reset too should be performed also in case an
entity is expired because it remains empty after receiving service
while not being the entity in service. But in this case the reset is
not performed.
This commit performs the above update of the finish time and reset of
the service received, also for an entity expiring while not being the
entity in service.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Antoine Tenart [Wed, 19 Sep 2018 09:39:31 +0000 (11:39 +0200)]
net: phy: phylink: ensure the carrier is off when starting phylink
[ Upstream commit
aeeb2e8fdefdd5d257a1446351c70cb3df540199 ]
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arend van Spriel [Wed, 5 Sep 2018 07:48:58 +0000 (09:48 +0200)]
brcmfmac: fix for proper support of 160MHz bandwidth
[ Upstream commit
330994e8e8ec5d0b269a5265e6032b37e29aa336 ]
Decoding of firmware channel information was not complete for 160MHz
support. This resulted in the following warning:
WARNING: CPU: 2 PID: 2222 at .../broadcom/brcm80211/brcmutil/d11.c:196
brcmu_d11ac_decchspec+0x2e/0x100 [brcmutil]
Modules linked in: brcmfmac(O) brcmutil(O) sha256_generic cfg80211 ...
CPU: 2 PID: 2222 Comm: kworker/2:0 Tainted: G O
4.17.0-wt-testing-x64-00002-gf1bed50 #1
Hardware name: Dell Inc. Latitude E6410/07XJP9, BIOS A07 02/15/2011
Workqueue: events request_firmware_work_func
RIP: 0010:brcmu_d11ac_decchspec+0x2e/0x100 [brcmutil]
RSP: 0018:
ffffc90000047bd0 EFLAGS:
00010206
RAX:
000000000000e832 RBX:
ffff8801146fe910 RCX:
ffff8801146fd3c0
RDX:
0000000000002800 RSI:
0000000000000070 RDI:
ffffc90000047c30
RBP:
ffffc90000047bd0 R08:
0000000000000000 R09:
ffffffffa0798c80
R10:
ffff88012bca55e0 R11:
ffff880110a4ea00 R12:
ffff8801146f8000
R13:
ffffc90000047c30 R14:
ffff8801146fe930 R15:
ffff8801138e02e0
FS:
0000000000000000(0000) GS:
ffff88012bc80000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f18ce8b8070 CR3:
000000000200a003 CR4:
00000000000206e0
Call Trace:
brcmf_setup_wiphybands+0x212/0x780 [brcmfmac]
brcmf_cfg80211_attach+0xae2/0x11a0 [brcmfmac]
brcmf_attach+0x1fc/0x4b0 [brcmfmac]
? __kmalloc+0x13c/0x1c0
brcmf_pcie_setup+0x99b/0xe00 [brcmfmac]
brcmf_fw_request_done+0x16a/0x1f0 [brcmfmac]
request_firmware_work_func+0x36/0x60
process_one_work+0x146/0x350
worker_thread+0x4a/0x3b0
kthread+0x102/0x140
? process_one_work+0x350/0x350
? kthread_bind+0x20/0x20
ret_from_fork+0x35/0x40
Code: 66 90 0f b7 07 55 48 89 e5 89 c2 88 47 02 88 47 03 66 81 e2 00 38
66 81 fa 00 18 74 6e 66 81 fa 00 20 74 39 66 81 fa 00 10 74 14 <0f>
0b 66 25 00 c0 74 20 66 3d 00 c0 75 20 c6 47 04 01 5d c3 66
---[ end trace
550c46682415b26d ]---
brcmfmac: brcmf_construct_chaninfo: Ignoring unexpected firmware channel 50
This patch adds the missing stuff to properly handle this.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
YueHaibing [Thu, 20 Sep 2018 01:58:18 +0000 (01:58 +0000)]
pinctrl: qcom: spmi-mpp: Fix err handling of pmic_mpp_set_mux
[ Upstream commit
69f8455f6cc78fa6cdf80d0105d7a748106271dc ]
'ret' should be returned while pmic_mpp_write_mode_ctl fails.
Fixes:
0e948042c420 ("pinctrl: qcom: spmi-mpp: Implement support for sink mode")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Sun, 16 Sep 2018 15:22:47 +0000 (16:22 +0100)]
x86: boot: Fix EFI stub alignment
[ Upstream commit
9c1442a9d039a1a3302fa93e9a11001c5f23b624 ]
We currently align the end of the compressed image to a multiple of
16. However, the PE-COFF header included in the EFI stub says that
the file alignment is 32 bytes, and when adding an EFI signature to
the file it must first be padded to this alignment.
sbsigntool commands warn about this:
warning: file-aligned section .text extends beyond end of file
warning: checksum areas are greater than image size. Invalid section table?
Worse, pesign -at least when creating a detached signature- uses the
hash of the unpadded file, resulting in an invalid signature if
padding is required.
Avoid both these problems by increasing alignment to 32 bytes when
CONFIG_EFI_STUB is enabled.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Hewitt [Tue, 4 Sep 2018 17:50:57 +0000 (21:50 +0400)]
Bluetooth: btbcm: Add entry for BCM4335C0 UART bluetooth
[ Upstream commit
a357ea098c9605f60d92a66a9073f56ce25726da ]
This patch adds the device ID for the AMPAK AP6335 combo module used
in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI
chip identifies itself as BCM4339, while Bluetooth identifies itself
as BCM4335 (rev C0):
```
[ 4.864248] Bluetooth: hci0: BCM: chip id 86
[ 4.866388] Bluetooth: hci0: BCM: features 0x2f
[ 4.889317] Bluetooth: hci0: BCM4335C0
[ 4.889332] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0000
[ 9.778383] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0268
```
Output from hciconfig:
```
hci0: Type: Primary Bus: UART
BD Address: 43:39:00:00:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING
RX bytes:7567 acl:234 sco:0 events:386 errors:0
TX bytes:53844 acl:77 sco:0 commands:304 errors:0
Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF
Link mode: SLAVE ACCEPT
Name: 'HUB'
Class: 0x0c0000
Service Classes: Rendering, Capturing
Device Class: Miscellaneous,
HCI Version: 4.0 (0x6) Revision: 0x10c
LMP Version: 4.0 (0x6) Subversion: 0x6109
Manufacturer: Broadcom Corporation (15)
```
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Wed, 5 Sep 2018 14:34:42 +0000 (15:34 +0100)]
signal: Introduce COMPAT_SIGMINSTKSZ for use in compat_sys_sigaltstack
[ Upstream commit
22839869f21ab3850fbbac9b425ccc4c0023926f ]
The sigaltstack(2) system call fails with -ENOMEM if the new alternative
signal stack is found to be smaller than SIGMINSTKSZ. On architectures
such as arm64, where the native value for SIGMINSTKSZ is larger than
the compat value, this can result in an unexpected error being reported
to a compat task. See, for example:
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=904385
This patch fixes the problem by extending do_sigaltstack to take the
minimum signal stack size as an additional parameter, allowing the
native and compat system call entry code to pass in their respective
values. COMPAT_SIGMINSTKSZ is just defined as SIGMINSTKSZ if it has not
been defined by the architecture.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Reported-by: Steve McIntyre <steve.mcintyre@arm.com>
Tested-by: Steve McIntyre <93sam@debian.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Tue, 18 Sep 2018 13:55:55 +0000 (08:55 -0500)]
mtd: rawnand: atmel: Fix potential NULL pointer dereference
[ Upstream commit
fbed20280d912449cfb40c382cb55e3d11502587 ]
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value")
Fixes:
f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Viresh Kumar [Wed, 3 Oct 2018 10:05:21 +0000 (15:35 +0530)]
cpufreq: dt: Try freeing static OPPs only if we have added them
[ Upstream commit
51c99dd2c06b234575661fa1e0a1dea6c3ef566f ]
We can not call dev_pm_opp_of_cpumask_remove_table() freely anymore
since the latest OPP core updates as that uses reference counting to
free resources. There are cases where no static OPPs are added (using
DT) for a platform and trying to remove the OPP table may end up
decrementing refcount which is already zero and hence generating
warnings.
Lets track if we were able to add static OPPs or not and then only
remove the table based on that. Some reshuffling of code is also done to
do that.
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dou Liyang [Fri, 24 Aug 2018 02:51:26 +0000 (10:51 +0800)]
ACPI / processor: Fix the return value of acpi_processor_ids_walk()
[ Upstream commit
d0381bf4f80c571dde1244fe5b85dc35e8b3f546 ]
ACPI driver should make sure all the processor IDs in their ACPI Namespace
are unique. the driver performs a depth-first walk of the namespace tree
and calls the acpi_processor_ids_walk() to check the duplicate IDs.
But, the acpi_processor_ids_walk() mistakes the return value. If a
processor is checked, it returns true which causes the walk break
immediately, and other processors will never be checked.
Repace the value with AE_OK which is the standard acpi_status value.
And don't abort the namespace walk even on error.
Fixes:
8c8cb30f49b8 (acpi/processor: Implement DEVICE operator for processor enumeration)
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lubomir Rintel [Thu, 4 Oct 2018 16:08:08 +0000 (18:08 +0200)]
x86/olpc: Indicate that legacy PC XO-1 platform should not register RTC
[ Upstream commit
d92116b800fb79a72ad26121f5011f6aa3ad94c2 ]
On OLPC XO-1, the RTC is discovered via device tree from the arch
initcall. Don't let the PC platform register another one from its device
initcall, it's not going to work:
sysfs: cannot create duplicate filename '/devices/platform/rtc_cmos'
CPU: 0 PID: 1 Comm: swapper Not tainted 4.19.0-rc6 #12
Hardware name: OLPC XO/XO, BIOS OLPC Ver 1.00.01 06/11/2014
Call Trace:
dump_stack+0x16/0x18
sysfs_warn_dup+0x46/0x58
sysfs_create_dir_ns+0x76/0x9b
kobject_add_internal+0xed/0x209
? __schedule+0x3fa/0x447
kobject_add+0x5b/0x66
device_add+0x298/0x535
? insert_resource_conflict+0x2a/0x3e
platform_device_add+0x14d/0x192
? io_delay_init+0x19/0x19
platform_device_register+0x1c/0x1f
add_rtc_cmos+0x16/0x31
do_one_initcall+0x78/0x14a
? do_early_param+0x75/0x75
kernel_init_freeable+0x152/0x1e0
? rest_init+0xa2/0xa2
kernel_init+0x8/0xd5
ret_from_fork+0x2e/0x38
kobject_add_internal failed for rtc_cmos with -EEXIST, don't try to
register things with the same name in the same directory.
platform rtc_cmos: registered platform RTC device (no PNP device found)
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
CC: "H. Peter Anvin" <hpa@zytor.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: x86-ml <x86@kernel.org>
Link: http://lkml.kernel.org/r/20181004160808.307738-1-lkundrak@v3.sk
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emmanuel Grumbach [Wed, 13 Jun 2018 08:49:20 +0000 (11:49 +0300)]
iwlwifi: mvm: clear HW_RESTART_REQUESTED when stopping the interface
[ Upstream commit
155f7e0441cd121b1e673d465a35e99f4b9b2f0b ]
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<
ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<
ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<
ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<
ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<
ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<
ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<
ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<
ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<
ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
Fixes:
bf8b286f86fc ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shaul Triebitz [Wed, 6 Jun 2018 14:20:58 +0000 (17:20 +0300)]
iwlwifi: pcie: avoid empty free RB queue
[ Upstream commit
868a1e863f95183f00809363fefba6d4f5bcd116 ]
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yu Zhao [Sun, 23 Sep 2018 20:39:24 +0000 (14:39 -0600)]
mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01
[ Upstream commit
5169894982bb67486d93cc1e10151712bb86bcb6 ]
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603
mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077
mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================
The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prarit Bhargava [Mon, 8 Oct 2018 15:06:19 +0000 (11:06 -0400)]
cpupower: Fix coredump on VMWare
[ Upstream commit
f69ffc5d3db8f1f03fd6d1df5930f9a1fbd787b6 ]
cpupower crashes on VMWare guests. The guests have the AMD PStateDef MSR
(0xC0010064 + state number) set to zero. As a result fid and did are zero
and the crash occurs because of a divide by zero (cof = fid/did). This
can be prevented by checking the enable bit in the PStateDef MSR before
calculating cof. By doing this the value of pstate[i] remains zero and
the value can be tested before displaying the active Pstates.
Check the enable bit in the PstateDef register for all supported families
and only print out enabled Pstates.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Stafford Horne <shorne@gmail.com>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sanskriti Sharma [Tue, 2 Oct 2018 14:29:10 +0000 (10:29 -0400)]
perf strbuf: Match va_{add,copy} with va_end
[ Upstream commit
ce49d8436cffa9b7a6a5f110879d53e89dbc6746 ]
Ensure that all code paths in strbuf_addv() call va_end() on the
ap_saved copy that was made.
Fixes the following coverity complaint:
Error: VARARGS (CWE-237): [#def683]
tools/perf/util/strbuf.c:106: missing_va_end: va_end was not called
for "ap_saved".
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-2-git-send-email-sansharm@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sanskriti Sharma [Tue, 2 Oct 2018 14:29:11 +0000 (10:29 -0400)]
perf tools: Cleanup trace-event-info 'tdata' leak
[ Upstream commit
faedbf3fd19f2511a39397f76359e4cc6ee93072 ]
Free tracing_data structure in tracing_data_get() error paths.
Fixes the following coverity complaint:
Error: RESOURCE_LEAK (CWE-772):
leaked_storage: Variable "tdata" going out of scope leaks the storage
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-3-git-send-email-sansharm@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sanskriti Sharma [Tue, 2 Oct 2018 14:29:14 +0000 (10:29 -0400)]
perf tools: Free temporary 'sys' string in read_event_files()
[ Upstream commit
1e44224fb0528b4c0cc176bde2bb31e9127eb14b ]
For each system in a given pevent, read_event_files() reads in a
temporary 'sys' string. Be sure to free this string before moving onto
to the next system and/or leaving read_event_files().
Fixes the following coverity complaints:
Error: RESOURCE_LEAK (CWE-772):
tools/perf/util/trace-event-read.c:343: overwrite_var: Overwriting
"sys" in "sys = read_string()" leaks the storage that "sys" points to.
tools/perf/util/trace-event-read.c:353: leaked_storage: Variable "sys"
going out of scope leaks the storage it points to.
Signed-off-by: Sanskriti Sharma <sansharm@redhat.com>
Reviewed-by: Jiri Olsa <jolsa@kernel.org>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Link: http://lkml.kernel.org/r/1538490554-8161-6-git-send-email-sansharm@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan Chancellor [Mon, 8 Oct 2018 18:08:47 +0000 (11:08 -0700)]
spi: spi-ep93xx: Use dma_data_direction for ep93xx_spi_dma_{finish,prepare}
[ Upstream commit
a1108c7b2efb892350ba6a0e932dfd45622f4e2b ]
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jia-Ju Bai [Tue, 9 Oct 2018 11:12:00 +0000 (13:12 +0200)]
lightnvm: pblk: fix two sleep-in-atomic-context bugs
[ Upstream commit
7325b4bbe5952e3e939f15de812f2ee0c0d33ca9 ]
The driver may sleep with holding a spinlock.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] nvm_dev_dma_alloc(GFP_KERNEL)
drivers/lightnvm/pblk-core.c, 754:
nvm_dev_dma_alloc in pblk_line_submit_smeta_io
drivers/lightnvm/pblk-core.c, 1048:
pblk_line_submit_smeta_io in pblk_line_init_bb
drivers/lightnvm/pblk-core.c, 1434:
pblk_line_init_bb in pblk_line_replace_data
drivers/lightnvm/pblk-recovery.c, 980:
pblk_line_replace_data in pblk_recov_l2p
drivers/lightnvm/pblk-recovery.c, 976:
spin_lock in pblk_recov_l2p
[FUNC] bio_map_kern(GFP_KERNEL)
drivers/lightnvm/pblk-core.c, 762:
bio_map_kern in pblk_line_submit_smeta_io
drivers/lightnvm/pblk-core.c, 1048:
pblk_line_submit_smeta_io in pblk_line_init_bb
drivers/lightnvm/pblk-core.c, 1434:
pblk_line_init_bb in pblk_line_replace_data
drivers/lightnvm/pblk-recovery.c, 980:
pblk_line_replace_data in pblk_recov_l2p
drivers/lightnvm/pblk-recovery.c, 976:
spin_lock in pblk_recov_l2p
To fix these bugs, the call to pblk_line_replace_data()
is moved out of the spinlock protection.
These bugs are found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thierry Reding [Fri, 21 Sep 2018 10:10:48 +0000 (12:10 +0200)]
hwmon: (pwm-fan) Set fan speed to 0 on suspend
[ Upstream commit
95dcd64bc5a27080beaa344edfe5bdcca3d2e7dc ]
Technically this is not required because disabling the PWM should be
enough. However, when support for atomic operations was implemented in
the PWM subsystem, only actual changes to the PWM channel are applied
during pwm_config(), which means that during after resume from suspend
the old settings won't be applied.
One possible solution is for the PWM driver to implement its own PM
operations such that settings from before suspend get applied on resume.
This has the disadvantage of completely ignoring any particular ordering
requirements that PWM user drivers might have, so it is best to leave it
up to the user drivers to apply the settings that they want at the
appropriate time.
Another way to solve this would be to read back the current state of the
PWM at the time of resume. That way, in case the configuration was lost
during suspend, applying the old settings in PWM user drivers would
actually get them applied because they differ from the current settings.
However, not all PWM drivers support reading the hardware state, and not
all hardware may support it.
The best workaround at this point seems to be to let PWM user drivers
tell the PWM subsystem that the PWM is turned off by, in addition to
disabling it, also setting the duty cycle to 0. This causes the resume
operation to apply a configuration that is different from the current
configuration, resulting in the proper state from before suspend getting
restored.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Janosch Frank [Tue, 2 Oct 2018 08:57:52 +0000 (10:57 +0200)]
s390/sthyi: Fix machine name validity indication
[ Upstream commit
b5130dc2224d1881f24224c0590c6d97f2168d6a ]
When running as a level 3 guest with no host provided sthyi support
sclp_ocf_cpc_name_copy() will only return zeroes. Zeroes are not a
valid group name, so let's not indicate that the group name field is
valid.
Also the group name is not dependent on stsi, let's not return based
on stsi before setting it.
Fixes:
95ca2cb57985 ("KVM: s390: Add sthyi emulation")
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serhey Popovych [Tue, 9 Oct 2018 18:21:01 +0000 (21:21 +0300)]
tun: Consistently configure generic netdev params via rtnetlink
[ Upstream commit
df52eab23d703142c766ac00bdb8db19d71238d0 ]
Configuring generic network device parameters on tun will fail in
presence of IFLA_INFO_KIND attribute in IFLA_LINKINFO nested attribute
since tun_validate() always return failure.
This can be visualized with following ip-link(8) command sequences:
# ip link set dev tun0 group 100
# ip link set dev tun0 group 100 type tun
RTNETLINK answers: Invalid argument
with contrast to dummy and veth drivers:
# ip link set dev dummy0 group 100
# ip link set dev dummy0 type dummy
# ip link set dev veth0 group 100
# ip link set dev veth0 group 100 type veth
Fix by returning zero in tun_validate() when @data is NULL that is
always in case since rtnl_link_ops->maxtype is zero in tun driver.
Fixes:
f019a7a594d9 ("tun: Implement ip link del tunXXX")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ryan C Goodfellow [Fri, 12 Oct 2018 18:09:01 +0000 (11:09 -0700)]
nfp: devlink port split support for 1x100G CXP NIC
[ Upstream commit
5948185b97fa1f83d7855e638a72982a1073ebf5 ]
This commit makes it possible to use devlink to split the 100G CXP
Netronome into two 40G interfaces. Currently when you ask for 2
interfaces, the math in src/nfp_devlink.c:nfp_devlink_port_split
calculates that you want 5 lanes per port because for some reason
eth_port.port_lanes=10 (shouldn't this be 12 for CXP?). What we really
want when asking for 2 breakout interfaces is 4 lanes per port. This
commit makes that happen by calculating based on 8 lanes if 10 are
present.
Signed-off-by: Ryan C Goodfellow <rgoodfel@isi.edu>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Greg Weeks <greg.weeks@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omar Sandoval [Thu, 11 Oct 2018 19:20:41 +0000 (12:20 -0700)]
swim: fix cleanup on setup error
[ Upstream commit
1448a2a5360ae06f25e2edc61ae070dff5c0beb4 ]
If we fail to allocate the request queue for a disk, we still need to
free that disk, not just the previous ones. Additionally, we need to
cleanup the previous request queues.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omar Sandoval [Thu, 11 Oct 2018 19:20:49 +0000 (12:20 -0700)]
ataflop: fix error handling during setup
[ Upstream commit
71327f547ee3a46ec5c39fdbbd268401b2578d0e ]
Move queue allocation next to disk allocation to fix a couple of issues:
- If add_disk() hasn't been called, we should clear disk->queue before
calling put_disk().
- If we fail to allocate a request queue, we still need to put all of
the disks, not just the ones that we allocated queues for.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiman Long [Fri, 19 Oct 2018 01:45:17 +0000 (21:45 -0400)]
locking/lockdep: Fix debug_locks off performance problem
[ Upstream commit
9506a7425b094d2f1d9c877ed5a78f416669269b ]
It was found that when debug_locks was turned off because of a problem
found by the lockdep code, the system performance could drop quite
significantly when the lock_stat code was also configured into the
kernel. For instance, parallel kernel build time on a 4-socket x86-64
server nearly doubled.
Further analysis into the cause of the slowdown traced back to the
frequent call to debug_locks_off() from the __lock_acquired() function
probably due to some inconsistent lockdep states with debug_locks
off. The debug_locks_off() function did an unconditional atomic xchg
to write a 0 value into debug_locks which had already been set to 0.
This led to severe cacheline contention in the cacheline that held
debug_locks. As debug_locks is being referenced in quite a few different
places in the kernel, this greatly slow down the system performance.
To prevent that trashing of debug_locks cacheline, lock_acquired()
and lock_contended() now checks the state of debug_locks before
proceeding. The debug_locks_off() function is also modified to check
debug_locks before calling __debug_locks_off().
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/1539913518-15598-1-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Fri, 19 Oct 2018 19:15:26 +0000 (21:15 +0200)]
i2c: rcar: cleanup DMA for all kinds of failure
[ Upstream commit
31d86033a0749a0463ea654130b2de5c163154f1 ]
DMA needs to be cleaned up not only on timeout, but on all errors where
it has been setup before.
Fixes:
73e8b0528346 ("i2c: rcar: add DMA support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Thu, 18 Oct 2018 13:13:02 +0000 (22:13 +0900)]
selftests: ftrace: Add synthetic event syntax testcase
[ Upstream commit
ba0e41ca81b935b958006c7120466e2217357827 ]
Add a testcase to check the syntax and field types for
synthetic_events interface.
Link: http://lkml.kernel.org/r/153986838264.18251.16627517536956299922.stgit@devbox
Acked-by: Shuah Khan <shuah@kernel.org>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan Chancellor [Sat, 13 Oct 2018 02:14:58 +0000 (19:14 -0700)]
net: qla3xxx: Remove overflowing shift statement
[ Upstream commit
8c3bf9b62b667456a57aefcf1689e826df146159 ]
Clang currently warns:
drivers/net/ethernet/qlogic/qla3xxx.c:384:24: warning: signed shift
result (0xF00000000) requires 37 bits to represent, but 'int' only has
32 bits [-Wshift-overflow]
((ISP_NVRAM_MASK << 16) | qdev->eeprom_cmd_data));
~~~~~~~~~~~~~~ ^ ~~
1 warning generated.
The warning is certainly accurate since ISP_NVRAM_MASK is defined as
(0x000F << 16) which is then shifted by 16, resulting in
64424509440,
well above UINT_MAX.
Given that this is the only location in this driver where ISP_NVRAM_MASK
is shifted again, it seems likely that ISP_NVRAM_MASK was originally
defined without a shift and during the move of the shift to the
definition, this statement wasn't properly removed (since ISP_NVRAM_MASK
is used in the statenent right above this). Only the maintainers can
confirm this since this statment has been here since the driver was
first added to the kernel.
Link: https://github.com/ClangBuiltLinux/linux/issues/127
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Andrzej Siewior [Tue, 16 Oct 2018 20:25:24 +0000 (22:25 +0200)]
x86/fpu: Remove second definition of fpu in __fpu__restore_sig()
[ Upstream commit
6aa676761d4c1acfa31320e55fa1f83f3fcbbc7a ]
Commit:
c5bedc6847c3b ("x86/fpu: Get rid of PF_USED_MATH usage, convert it to fpu->fpstate_active")
introduced the 'fpu' variable at top of __restore_xstate_sig(),
which now shadows the other definition:
arch/x86/kernel/fpu/signal.c:318:28: warning: symbol 'fpu' shadows an earlier one
arch/x86/kernel/fpu/signal.c:271:20: originally declared here
Remove the shadowed definition of 'fpu', as the two definitions are the same.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes:
c5bedc6847c3b ("x86/fpu: Get rid of PF_USED_MATH usage, convert it to fpu->fpstate_active")
Link: http://lkml.kernel.org/r/20181016202525.29437-3-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Miller [Fri, 12 Oct 2018 05:46:55 +0000 (22:46 -0700)]
perf cpu_map: Align cpu map synthesized events properly.
[ Upstream commit
0ed149cf5239cc6e7e65bf00f769e8f1e91076c0 ]
The size of the resulting cpu map can be smaller than a multiple of
sizeof(u64), resulting in SIGBUS on cpus like Sparc as the next event
will not be aligned properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Fixes:
6c872901af07 ("perf cpu_map: Add cpu_map event synthesize function")
Link: http://lkml.kernel.org/r/20181011.224655.716771175766946817.davem@davemloft.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jarod Wilson [Thu, 6 Sep 2018 22:18:12 +0000 (18:18 -0400)]
perf tools: Fix use of alternatives to find JDIR
[ Upstream commit
36b8d4628d3cc8f5a748e508cce8673bc00fc63c ]
When a build is run from something like a cron job, the user's $PATH is
rather minimal, of note, not including /usr/sbin in my own case. Because
of that, an automated rpm package build ultimately fails to find
libperf-jvmti.so, because somewhere within the build, this happens...
/bin/sh: alternatives: command not found
/bin/sh: alternatives: command not found
Makefile.config:849: No openjdk development package found, please install
JDK package, e.g. openjdk-8-jdk, java-1.8.0-openjdk-devel
...and while the build continues, libperf-jvmti.so isn't built, and
things fall down when rpm tries to find all the %files specified. Exact
same system builds everything just fine when the job is launched from a
login shell instead of a cron job, since alternatives is in $PATH, so
openjdk is actually found.
The test required to get into this section of code actually specifies
the full path, as does a block just above it, so let's do that here too.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: William Cohen <wcohen@redhat.com>
Fixes:
d4dfdf00d43e ("perf jvmti: Plug compilation into perf build")
Link: http://lkml.kernel.org/r/20180906221812.11167-1-jarod@redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Song Muchun [Sun, 14 Oct 2018 11:26:12 +0000 (19:26 +0800)]
sched/fair: Fix the min_vruntime update logic in dequeue_entity()
[ Upstream commit
9845c49cc9bbb317a0bc9e9cf78d8e09d54c9af0 ]
The comment and the code around the update_min_vruntime() call in
dequeue_entity() are not in agreement.
>From commit:
b60205c7c558 ("sched/fair: Fix min_vruntime tracking")
I think that we want to update min_vruntime when a task is sleeping/migrating.
So, the check is inverted there - fix it.
Signed-off-by: Song Muchun <smuchun@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes:
b60205c7c558 ("sched/fair: Fix min_vruntime tracking")
Link: http://lkml.kernel.org/r/20181014112612.2614-1-smuchun@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Mon, 15 Oct 2018 03:19:31 +0000 (20:19 -0700)]
sparc64: Make proc_id signed.
[ Upstream commit
b3e1eb8e7ac9aaa283989496651d99267c4cad6c ]
So that when it is unset, ie. '-1', userspace can see it
properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Fri, 12 Oct 2018 17:33:20 +0000 (10:33 -0700)]
sparc: Throttle perf events properly.
[ Upstream commit
455adb3174d2c8518cef1a61140c211f6ac224d2 ]
Like x86 and arm, call perf_sample_event_took() in perf event
NMI interrupt handler.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David S. Miller [Fri, 12 Oct 2018 17:31:58 +0000 (10:31 -0700)]
sparc: Fix single-pcr perf event counter management.
[ Upstream commit
cfdc3170d214046b9509183fe9b9544dc644d40b ]
It is important to clear the hw->state value for non-stopped events
when they are added into the PMU. Otherwise when the event is
scheduled out, we won't read the counter because HES_UPTODATE is still
set. This breaks 'perf stat' and similar use cases, causing all the
events to show zero.
This worked for multi-pcr because we make explicit sparc_pmu_start()
calls in calculate_multiple_pcrs(). calculate_single_pcr() doesn't do
this because the idea there is to accumulate all of the counter
settings into the single pcr value. So we have to add explicit
hw->state handling there.
Like x86, we use the PERF_HES_ARCH bit to track truly stopped events
so that we don't accidently start them on a reload.
Related to all of this, sparc_pmu_start() is missing a userpage update
so add it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Olsa [Wed, 10 Oct 2018 08:03:39 +0000 (10:03 +0200)]
perf vendor events intel: Fix wrong filter_band* values for uncore events
[ Upstream commit
94aafb74cee0002e2f2eb6dc5376f54d5951ab4d ]
Michael reported that he could not stat following event:
$ perf stat -e unc_p_freq_ge_1200mhz_cycles -a -- ls
event syntax error: '..e_1200mhz_cycles'
\___ value too big for format, maximum is 255
Run 'perf list' for a list of valid events
The event is unwrapped into:
uncore_pcu/event=0xb,filter_band0=1200/
where filter_band0 format says it's one byte only:
# cat uncore_pcu/format/filter_band0
config1:0-7
while JSON files specifies bigger number:
"Filter": "filter_band0=1200",
all the filter_band* formats show 1 byte width:
# cat uncore_pcu/format/filter_band1
config1:8-15
# cat uncore_pcu/format/filter_band2
config1:16-23
# cat uncore_pcu/format/filter_band3
config1:24-31
The reason of the issue is that filter_band* values are supposed to be
in 100Mhz units.. it's stated in the JSON help for the events, like:
filter_band3=XXX, with XXX in 100Mhz units
This patch divides the filter_band* values by 100, plus there's couple
of changes that actually change the number completely, like:
- "Filter": "edge=1,filter_band2=4000",
+ "Filter": "edge=1,filter_band2=30",
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20181010080339.GB15790@krava
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian Westphal [Wed, 10 Oct 2018 16:02:21 +0000 (18:02 +0200)]
xfrm: policy: use hlist rcu variants on insert
[ Upstream commit
9dffff200fd178f11dd50eb1fd8ccd0650c9284e ]
bydst table/list lookups use rcu, so insertions must use rcu versions.
Fixes:
a7c44247f704e ("xfrm: policy: make xfrm_policy_lookup_bytype lockless")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Olsa [Wed, 3 Oct 2018 07:20:46 +0000 (09:20 +0200)]
Revert "perf tools: Fix PMU term format max value calculation"
[ Upstream commit
1b9caa10b31dda0866f4028e4bfb923fb6e4072f ]
This reverts commit
ac0e2cd555373ae6f8f3a3ad3fbbf5b6d1e7aaaa.
Michael reported an issue with oversized terms values assignment
and I noticed there was actually a misunderstanding of the max
value check in the past.
The above commit's changelog says:
If bit 21 is set, there is parsing issues as below.
$ perf stat -a -e uncore_qpi_0/event=0x200002,umask=0x8/
event syntax error: '..pi_0/event=0x200002,umask=0x8/'
\___ value too big for format, maximum is 511
But there's no issue there, because the event value is distributed
along the value defined by the format. Even if the format defines
separated bit, the value is treated as a continual number, which
should follow the format definition.
In above case it's 9-bit value with last bit separated:
$ cat uncore_qpi_0/format/event
config:0-7,21
Hence the value 0x200002 is correctly reported as format violation,
because it exceeds 9 bits. It should have been 0x102 instead, which
sets the 9th bit - the bit 21 of the format.
$ perf stat -vv -a -e uncore_qpi_0/event=0x102,umask=0x8/
Using CPUID GenuineIntel-6-2D
...
------------------------------------------------------------
perf_event_attr:
type 10
size 112
config 0x200802
sample_type IDENTIFIER
...
Reported-by: Michael Petlan <mpetlan@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes:
ac0e2cd55537 ("perf tools: Fix PMU term format max value calculation")
Link: http://lkml.kernel.org/r/20181003072046.29276-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Sat, 6 Oct 2018 02:38:46 +0000 (19:38 -0700)]
bpf: do not blindly change rlimit in reuseport net selftest
[ Upstream commit
262f9d811c7608f1e74258ceecfe1fa213bdf912 ]
If the current process has unlimited RLIMIT_MEMLOCK,
we should should leave it as is.
Fixes:
941ff6f11c02 ("bpf: fix rlimit in reuseport net selftest")
Signed-off-by: John Sperbeck <jsperbeck@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Szyprowski [Wed, 5 Sep 2018 10:02:15 +0000 (12:02 +0200)]
ARM: dts: exynos: Disable pull control for MAX8997 interrupts on Origen
commit
f5e758b8358f6c27e8a351ddf0b441a64cdabb94 upstream.
PMIC_IRQB and PMIC_KEYINB lines on Exynos4210-based Origen board have
external pull-up resistors, so disable any pull control for those lines
in respective pin controller node. This fixes support for MAX8997
interrupts and enables operation of wakeup from MAX8997 RTC alarm.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes:
17419726aaa1 ("ARM: dts: add max8997 device node for exynos4210-origen board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sai Praneeth [Wed, 1 Aug 2018 18:42:25 +0000 (11:42 -0700)]
x86/speculation: Support Enhanced IBRS on future CPUs
commit
706d51681d636a0c4a5ef53395ec3b803e45ed4d upstream.
Future Intel processors will support "Enhanced IBRS" which is an "always
on" mode i.e. IBRS bit in SPEC_CTRL MSR is enabled once and never
disabled.
From the specification [1]:
"With enhanced IBRS, the predicted targets of indirect branches
executed cannot be controlled by software that was executed in a less
privileged predictor mode or on another logical processor. As a
result, software operating on a processor with enhanced IBRS need not
use WRMSR to set IA32_SPEC_CTRL.IBRS after every transition to a more
privileged predictor mode. Software can isolate predictor modes
effectively simply by setting the bit once. Software need not disable
enhanced IBRS prior to entering a sleep state such as MWAIT or HLT."
If Enhanced IBRS is supported by the processor then use it as the
preferred spectre v2 mitigation mechanism instead of Retpoline. Intel's
Retpoline white paper [2] states:
"Retpoline is known to be an effective branch target injection (Spectre
variant 2) mitigation on Intel processors belonging to family 6
(enumerated by the CPUID instruction) that do not have support for
enhanced IBRS. On processors that support enhanced IBRS, it should be
used for mitigation instead of retpoline."
The reason why Enhanced IBRS is the recommended mitigation on processors
which support it is that these processors also support CET which
provides a defense against ROP attacks. Retpoline is very similar to ROP
techniques and might trigger false positives in the CET defense.
If Enhanced IBRS is selected as the mitigation technique for spectre v2,
the IBRS bit in SPEC_CTRL MSR is set once at boot time and never
cleared. Kernel also has to make sure that IBRS bit remains set after
VMEXIT because the guest might have cleared the bit. This is already
covered by the existing x86_spec_ctrl_set_guest() and
x86_spec_ctrl_restore_host() speculation control functions.
Enhanced IBRS still requires IBPB for full mitigation.
[1] Speculative-Execution-Side-Channel-Mitigations.pdf
[2] Retpoline-A-Branch-Target-Injection-Mitigation.pdf
Both documents are available at:
https://bugzilla.kernel.org/show_bug.cgi?id=199511
Originally-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Sai Praneeth Prakhya <sai.praneeth.prakhya@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim C Chen <tim.c.chen@intel.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Link: https://lkml.kernel.org/r/1533148945-24095-1-git-send-email-sai.praneeth.prakhya@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Andrzej Siewior [Wed, 17 Oct 2018 10:34:32 +0000 (12:34 +0200)]
x86/mm/pat: Disable preemption around __flush_tlb_all()
commit
f77084d96355f5fba8e2c1fb3a51a393b1570de7 upstream.
The WARN_ON_ONCE(__read_cr3() != build_cr3()) in switch_mm_irqs_off()
triggers every once in a while during a snapshotted system upgrade.
The warning triggers since commit
decab0888e6e ("x86/mm: Remove
preempt_disable/enable() from __native_flush_tlb()"). The callchain is:
get_page_from_freelist() -> post_alloc_hook() -> __kernel_map_pages()
with CONFIG_DEBUG_PAGEALLOC enabled.
Disable preemption during CR3 reset / __flush_tlb_all() and add a comment
why preemption has to be disabled so it won't be removed accidentaly.
Add another preemptible() check in __flush_tlb_all() to catch callers with
enabled preemption when PGE is enabled, because PGE enabled does not
trigger the warning in __native_flush_tlb(). Suggested by Andy Lutomirski.
Fixes:
decab0888e6e ("x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181017103432.zgv46nlu3hc7k4rq@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
He Zhe [Tue, 14 Aug 2018 15:33:42 +0000 (23:33 +0800)]
x86/corruption-check: Fix panic in memory_corruption_check() when boot option without value is provided
commit
ccde460b9ae5c2bd5e4742af0a7f623c2daad566 upstream.
memory_corruption_check[{_period|_size}]()'s handlers do not check input
argument before passing it to kstrtoul() or simple_strtoull(). The argument
would be a NULL pointer if each of the kernel parameters, without its
value, is set in command line and thus cause the following panic.
PANIC: early exception 0xe3 IP 10:
ffffffff73587c22 error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.18-rc8+ #2
[ 0.000000] RIP: 0010:kstrtoull+0x2/0x10
...
[ 0.000000] Call Trace
[ 0.000000] ? set_corruption_check+0x21/0x49
[ 0.000000] ? do_early_param+0x4d/0x82
[ 0.000000] ? parse_args+0x212/0x330
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_options+0x20/0x23
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_param+0x2d/0x39
[ 0.000000] ? setup_arch+0x2f7/0xbf4
[ 0.000000] ? start_kernel+0x5e/0x4c2
[ 0.000000] ? load_ucode_bsp+0x113/0x12f
[ 0.000000] ? secondary_startup_64+0xa5/0xb0
This patch adds checks to prevent the panic.
Signed-off-by: He Zhe <zhe.he@windriver.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: gregkh@linuxfoundation.org
Cc: kstewart@linuxfoundation.org
Cc: pombredanne@nexb.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1534260823-87917-1-git-send-email-zhe.he@windriver.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Juergen Gross [Wed, 10 Oct 2018 06:14:54 +0000 (08:14 +0200)]
x86/xen: Fix boot loader version reported for PVH guests
commit
357d291ce035d1b757568058f3c9898c60d125b1 upstream.
The boot loader version reported via sysfs is wrong in case of the
kernel being booted via the Xen PVH boot entry. it should be 2.12
(0x020c), but it is reported to be 2.18 (0x0212).
As the current way to set the version is error prone use the more
readable variant (2 << 8) | 12.
Signed-off-by: Juergen Gross <jgross@suse.com>
Cc: <stable@vger.kernel.org> # 4.12
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: boris.ostrovsky@oracle.com
Cc: bp@alien8.de
Cc: corbet@lwn.net
Cc: linux-doc@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20181010061456.22238-2-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jiri Kosina [Tue, 25 Sep 2018 12:38:55 +0000 (14:38 +0200)]
x86/speculation: Enable cross-hyperthread spectre v2 STIBP mitigation
commit
53c613fe6349994f023245519265999eed75957f upstream.
STIBP is a feature provided by certain Intel ucodes / CPUs. This feature
(once enabled) prevents cross-hyperthread control of decisions made by
indirect branch predictors.
Enable this feature if
- the CPU is vulnerable to spectre v2
- the CPU supports SMT and has SMT siblings online
- spectre_v2 mitigation autoselection is enabled (default)
After some previous discussion, this leaves STIBP on all the time, as wrmsr
on crossing kernel boundary is a no-no. This could perhaps later be a bit
more optimized (like disabling it in NOHZ, experiment with disabling it in
idle, etc) if needed.
Note that the synchronization of the mask manipulation via newly added
spec_ctrl_mutex is currently not strictly needed, as the only updater is
already being serialized by cpu_add_remove_lock, but let's make this a
little bit more future-proof.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: "WoodhouseDavid" <dwmw@amazon.co.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: "SchauflerCasey" <casey.schaufler@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/nycvar.YFH.7.76.1809251438240.15880@cbobk.fhfr.pm
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex Stanoev [Sun, 28 Oct 2018 16:55:12 +0000 (16:55 +0000)]
ALSA: ca0106: Disable IZD on SB0570 DAC to fix audio pops
commit
ac237c28d5ac1b241d58b1b7b4b9fa10efb22fb5 upstream.
The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.
The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.
The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.
This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
Signed-off-by: Alex Stanoev <alex@astanoev.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeremy Cline [Thu, 11 Oct 2018 19:49:17 +0000 (15:49 -0400)]
ALSA: hda - Add mic quirk for the Lenovo G50-30 (17aa:3905)
commit
e7bb6ad5685f05685dd8a6a5eda7bfcd14d5f95b upstream.
The Lenovo G50-30, like other G50 models, has a Conexant codec that
requires a quirk for its inverted stereo dmic.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1249364
Reported-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Tested-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hui Wang [Wed, 10 Oct 2018 03:57:25 +0000 (11:57 +0800)]
ALSA: hda/realtek - Fix the problem of the front MIC on the Lenovo M715
commit
d06fb562bff5d14defdacbd92449bacbaedd5cdf upstream.
The front MIC on the Lenovo M715 can't record sound, after applying
the ALC294_FIXUP_LENOVO_MIC_LOCATION, the problem is fixed. So add
the pin configuration of this machine to the pin quirk table.
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 9 Oct 2018 12:20:17 +0000 (14:20 +0200)]
ALSA: hda - Fix headphone pin config for ASUS G751
commit
5b7c5e1f4c36b99d0f694f38b9ad910f520cb7ef upstream.
BIOS on ASUS G751 doesn't seem to map the headphone pin (NID 0x16)
correctly. Add a quirk to address it, as well as chaining to the
previous fix for the microphone.
Reported-by: Håvard <hovardslill@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Sun, 7 Oct 2018 07:44:17 +0000 (09:44 +0200)]
ALSA: hda - Add quirk for ASUS G751 laptop
commit
11ba6111160290ccd35562f4e05cec08942a6c4c upstream.
ASUS G751 requires the extra COEF initialization to make it microphone
working properly.
Reported-and-tested-by: Håvard <hovardslill@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Sun, 14 Oct 2018 19:58:00 +0000 (21:58 +0200)]
parisc: Fix exported address of os_hpmc handler
commit
99a3ae51d557d8e38a7aece65678a31f9db215ee upstream.
In the C-code we need to put the physical address of the hpmc handler in
the interrupt vector table (IVA) in order to get HPMCs working. Since
on parisc64 function pointers are indirect (in fact they are function
descriptors) we instead export the address as variable and not as
function.
This reverts a small part of commit
f39cce654f9a ("parisc: Add
cfi_startproc and cfi_endproc to assembly code").
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> [4.9+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Fri, 12 Oct 2018 20:37:46 +0000 (22:37 +0200)]
parisc: Fix map_pages() to not overwrite existing pte entries
commit
3c229b3f2dd8133f61bb81d3cb018be92f4bba39 upstream.
Fix a long-existing small nasty bug in the map_pages() implementation which
leads to overwriting already written pte entries with zero, *if* map_pages() is
called a second time with an end address which isn't aligned on a pmd boundry.
This happens for example if we want to remap only the text segment read/write
in order to run alternative patching on the code. Exiting the loop when we
reach the end address fixes this.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John David Anglin [Sat, 6 Oct 2018 17:11:30 +0000 (13:11 -0400)]
parisc: Fix address in HPMC IVA
commit
1138b6718ff74d2a934459643e3754423d23b5e2 upstream.
Helge noticed that the address of the os_hpmc handler was not being
correctly calculated in the hpmc macro. As a result, PDCE_CHECK would
fail to call os_hpmc:
<Cpu2>
e800009802e00000 0000000000000000 CC_ERR_CHECK_HPMC
<Cpu2>
37000f7302e00000 8040004000000000 CC_ERR_CPU_CHECK_SUMMARY
<Cpu2>
f600105e02e00000 fffffff0f0c00000 CC_MC_HPMC_MONARCH_SELECTED
<Cpu2>
140003b202e00000 000000000000000b CC_ERR_HPMC_STATE_ENTRY
<Cpu2>
5600100b02e00000 00000000000001a0 CC_MC_OS_HPMC_LEN_ERR
<Cpu2>
5600106402e00000 fffffff0f0438e70 CC_MC_BR_TO_OS_HPMC_FAILED
<Cpu2>
e800009802e00000 0000000000000000 CC_ERR_CHECK_HPMC
<Cpu2>
37000f7302e00000 8040004000000000 CC_ERR_CPU_CHECK_SUMMARY
<Cpu2>
4000109f02e00000 0000000000000000 CC_MC_HPMC_INITIATED
<Cpu2>
4000101902e00000 0000000000000000 CC_MC_MULTIPLE_HPMCS
<Cpu2>
030010d502e00000 0000000000000000 CC_CPU_STOP
The address problem can be seen by dumping the fault vector:
0000000040159000 <fault_vector_20>:
40159000: 63 6f 77 73 stb r15,-2447(dp)
40159004: 20 63 61 6e ldil L%b747000,r3
40159008: 20 66 6c 79 ldil L%-
1c3b3000,r3
...
40159020: 08 00 02 40 nop
40159024: 20 6e 60 02 ldil L%15d000,r3
40159028: 34 63 00 00 ldo 0(r3),r3
4015902c: e8 60 c0 02 bv,n r0(r3)
40159030: 08 00 02 40 nop
40159034: 00 00 00 00 break 0,0
40159038: c0 00 70 00 bb,*< r0,sar,
40159840 <fault_vector_20+0x840>
4015903c: 00 00 00 00 break 0,0
Location
40159038 should contain the physical address of os_hpmc:
000000004015d000 <os_hpmc>:
4015d000: 08 1a 02 43 copy r26,r3
4015d004: 01 c0 08 a4 mfctl iva,r4
4015d008: 48 85 00 68 ldw 34(r4),r5
This patch moves the address setup into initialize_ivt to resolve the
above problem. I tested the change by dumping the HPMC entry after setup:
0000000040209020: 8000240
0000000040209024:
206a2004
0000000040209028:
34630ac0
000000004020902c:
e860c002
0000000040209030: 8000240
0000000040209034:
1bdddce6
0000000040209038: 15d000
000000004020903c: 1a0
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Glauber [Thu, 11 Oct 2018 10:13:01 +0000 (12:13 +0200)]
ipmi: Fix timer race with module unload
commit
0711e8c1b4572d076264e71b0002d223f2666ed7 upstream.
Please note that below oops is from an older kernel, but the same
race seems to be present in the upstream kernel too.
---8<---
The following panic was encountered during removing the ipmi_ssif
module:
[ 526.352555] Unable to handle kernel paging request at virtual address
ffff000006923090
[ 526.360464] Mem abort info:
[ 526.363257] ESR = 0x86000007
[ 526.366304] Exception class = IABT (current EL), IL = 32 bits
[ 526.372221] SET = 0, FnV = 0
[ 526.375269] EA = 0, S1PTW = 0
[ 526.378405] swapper pgtable: 4k pages, 48-bit VAs, pgd =
000000008ae60416
[ 526.385185] [
ffff000006923090] *pgd=
000000bffcffe803, *pud=
000000bffcffd803, *pmd=
0000009f4731a003, *pte=
0000000000000000
[ 526.396141] Internal error: Oops:
86000007 [#1] SMP
[ 526.401008] Modules linked in: nls_iso8859_1 ipmi_devintf joydev input_leds ipmi_msghandler shpchp sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear i2c_smbus hid_generic usbhid uas hid usb_storage ast aes_ce_blk i2c_algo_bit aes_ce_cipher qede ttm crc32_ce ptp crct10dif_ce drm_kms_helper ghash_ce syscopyarea sha2_ce sysfillrect sysimgblt pps_core fb_sys_fops sha256_arm64 sha1_ce mpt3sas qed drm raid_class ahci scsi_transport_sas libahci gpio_xlp i2c_xlp9xx aes_neon_bs aes_neon_blk crypto_simd cryptd aes_arm64 [last unloaded: ipmi_ssif]
[ 526.468085] CPU: 125 PID: 0 Comm: swapper/125 Not tainted 4.15.0-35-generic #38~lp1775396+build.1
[ 526.476942] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL022 08/14/2018
[ 526.484932] pstate:
00400009 (nzcv daif +PAN -UAO)
[ 526.489713] pc : 0xffff000006923090
[ 526.493198] lr : call_timer_fn+0x34/0x178
[ 526.497194] sp :
ffff000009b0bdd0
[ 526.500496] x29:
ffff000009b0bdd0 x28:
0000000000000082
[ 526.505796] x27:
0000000000000002 x26:
ffff000009515188
[ 526.511096] x25:
ffff000009515180 x24:
ffff0000090f1018
[ 526.516396] x23:
ffff000009519660 x22:
dead000000000200
[ 526.521696] x21:
ffff000006923090 x20:
0000000000000100
[ 526.526995] x19:
ffff809eeb466a40 x18:
0000000000000000
[ 526.532295] x17:
000000000000000e x16:
0000000000000007
[ 526.537594] x15:
0000000000000000 x14:
071c71c71c71c71c
[ 526.542894] x13:
0000000000000000 x12:
0000000000000000
[ 526.548193] x11:
0000000000000001 x10:
ffff000009b0be88
[ 526.553493] x9 :
0000000000000000 x8 :
0000000000000005
[ 526.558793] x7 :
ffff80befc1f8528 x6 :
0000000000000020
[ 526.564092] x5 :
0000000000000040 x4 :
0000000020001b20
[ 526.569392] x3 :
0000000000000000 x2 :
ffff809eeb466a40
[ 526.574692] x1 :
ffff000006923090 x0 :
ffff809eeb466a40
[ 526.579992] Process swapper/125 (pid: 0, stack limit = 0x000000002eb50acc)
[ 526.586854] Call trace:
[ 526.589289] 0xffff000006923090
[ 526.592419] expire_timers+0xc8/0x130
[ 526.596070] run_timer_softirq+0xec/0x1b0
[ 526.600070] __do_softirq+0x134/0x328
[ 526.603726] irq_exit+0xc8/0xe0
[ 526.606857] __handle_domain_irq+0x6c/0xc0
[ 526.610941] gic_handle_irq+0x84/0x188
[ 526.614679] el1_irq+0xe8/0x180
[ 526.617822] cpuidle_enter_state+0xa0/0x328
[ 526.621993] cpuidle_enter+0x34/0x48
[ 526.625564] call_cpuidle+0x44/0x70
[ 526.629040] do_idle+0x1b8/0x1f0
[ 526.632256] cpu_startup_entry+0x2c/0x30
[ 526.636174] secondary_start_kernel+0x11c/0x130
[ 526.640694] Code: bad PC value
[ 526.643800] ---[ end trace
d020b0b8417c2498 ]---
[ 526.648404] Kernel panic - not syncing: Fatal exception in interrupt
[ 526.654778] SMP: stopping secondary CPUs
[ 526.658734] Kernel Offset: disabled
[ 526.662211] CPU features: 0x5800c38
[ 526.665688] Memory Limit: none
[ 526.668768] ---[ end Kernel panic - not syncing: Fatal exception in interrupt
Prevent mod_timer from arming a timer that was already removed by
del_timer during module unload.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Cc: <stable@vger.kernel.org> # 3.19
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maciej S. Szmigiero [Sat, 8 Sep 2018 23:21:06 +0000 (01:21 +0200)]
pcmcia: Implement CLKRUN protocol disabling for Ricoh bridges
commit
95691e3eddc41da2d1cd3cca51fecdfb46bd85bc upstream.
Currently, "disable_clkrun" yenta_socket module parameter is only
implemented for TI CardBus bridges.
Add also an implementation for Ricoh bridges that have the necessary
setting documented in publicly available datasheets.
Tested on a RL5C476II with a Sunrich C-160 CardBus NIC that doesn't work
correctly unless the CLKRUN protocol is disabled.
Let's also make it clear in its description that the "disable_clkrun"
module parameter only works on these two previously mentioned brands of
CardBus bridges.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafael J. Wysocki [Mon, 15 Oct 2018 21:21:05 +0000 (23:21 +0200)]
cpufreq: conservative: Take limits changes into account properly
commit
da5e79bc70b84971d2b3a55fb252e34e51d81d48 upstream.
If the policy limits change between invocations of cs_dbs_update(),
the requested frequency value stored in dbs_info may not be updated
and the function may use a stale value of it next time. Moreover, if
idle periods are takem into account by cs_dbs_update(), the requested
frequency value stored in dbs_info may be below the min policy limit,
which is incorrect.
To fix these problems, always update the requested frequency value
in dbs_info along with the local copy of it when the previous
requested frequency is beyond the policy limits and avoid decreasing
the requested frequency below the min policy limit when taking
idle periods into account.
Fixes:
abb6627910a1 (cpufreq: conservative: Fix next frequency selection)
Fixes:
00bfe05889e9 (cpufreq: conservative: Decrease frequency faster for deferred updates)
Reported-by: Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Waldemar Rymarkiewicz <waldemarx.rymarkiewicz@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hou Tao [Sat, 6 Oct 2018 09:09:35 +0000 (17:09 +0800)]
jffs2: free jffs2_sb_info through jffs2_kill_sb()
commit
92e2921f7eee63450a5f953f4b15dc6210219430 upstream.
When an invalid mount option is passed to jffs2, jffs2_parse_options()
will fail and jffs2_sb_info will be freed, but then jffs2_sb_info will
be used (use-after-free) and freeed (double-free) in jffs2_kill_sb().
Fix it by removing the buggy invocation of kfree() when getting invalid
mount options.
Fixes:
92abc475d8de ("jffs2: implement mount option parsing and compression overriding")
Cc: stable@kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry Bazhenov [Mon, 15 Oct 2018 09:21:22 +0000 (14:21 +0500)]
hwmon: (pmbus) Fix page count auto-detection.
commit
e7c6a55606b5c46b449d76588968b4d8caae903f upstream.
Devices with compatible="pmbus" field have zero initial page count,
and pmbus_clear_faults() being called before the page count auto-
detection does not actually clear faults because it depends on the
page count. Non-cleared faults in its turn may fail the subsequent
page count auto-detection.
This patch fixes this problem by calling pmbus_clear_fault_page()
for currently set page and calling pmbus_clear_faults() after the
page count was detected.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Bazhenov <bazhenov.dn@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tang Junhui [Mon, 8 Oct 2018 12:41:14 +0000 (20:41 +0800)]
bcache: fix miss key refill->end in writeback
commit
2d6cb6edd2c7fb4f40998895bda45006281b1ac5 upstream.
refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
if (bkey_cmp(k, refill->end) >= 0) {
ret = MAP_DONE;
goto out;
}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tang Junhui [Mon, 8 Oct 2018 12:41:08 +0000 (20:41 +0800)]
bcache: trace missed reading by cache_missed
commit
502b291568fc7faf1ebdb2c2590f12851db0ff76 upstream.
Missed reading IOs are identified by s->cache_missed, not the
s->cache_miss, so in trace_bcache_read() using trace_bcache_read
to identify whether the IO is missed or not.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rafał Miłecki [Thu, 11 Oct 2018 07:42:17 +0000 (09:42 +0200)]
spi: bcm-qspi: switch back to reading flash using smaller chunks
commit
940ec770c295682993d1cccce3081fd7c74fece8 upstream.
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes:
345309fa7c0c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Xiang [Tue, 28 Aug 2018 14:32:57 +0000 (22:32 +0800)]
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
commit
41fe242979e463d6ad251077ded01b825a330b7e upstream.
If the size of spi-nor flash is larger than 16MB, the read_opcode
is set to SPINOR_OP_READ_1_1_4_4B, and fsl_qspi_get_seqid() will
return -EINVAL when cmd is SPINOR_OP_READ_1_1_4_4B. This can
cause read operation fail.
Fixes:
e46ecda764dc ("mtd: spi-nor: Add Freescale QuadSPI driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 10 Nov 2018 15:48:36 +0000 (07:48 -0800)]
Linux 4.14.80
Christophe Leroy [Tue, 16 Jan 2018 09:33:05 +0000 (10:33 +0100)]
net: fs_enet: do not call phy_stop() in interrupts
[ Upstream commit
f8b39039cbf2a15f2b8c9f081e1cbd5dee00aaf5 ]
In case of TX timeout, fs_timeout() calls phy_stop(), which
triggers the following BUG_ON() as we are in interrupt.
[92708.199889] kernel BUG at drivers/net/phy/mdio_bus.c:482!
[92708.204985] Oops: Exception in kernel mode, sig: 5 [#1]
[92708.210119] PREEMPT
[92708.212107] CMPC885
[92708.214216] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W 4.9.61 #39
[92708.223227] task:
c60f0a40 task.stack:
c6104000
[92708.227697] NIP:
c02a84bc LR:
c02a947c CTR:
c02a93d8
[92708.232614] REGS:
c6105c70 TRAP: 0700 Tainted: G W (4.9.61)
[92708.241193] MSR:
00021032 <ME,IR,DR,RI>[92708.244818] CR:
24000822 XER:
20000000
[92708.248767]
GPR00:
c02a947c c6105d20 c60f0a40 c62b4c00 00000005 0000001f c069aad8 0001a688
GPR08:
00000007 00000100 c02a93d8 00000000 000005fc 00000000 c6213240 c06338e4
GPR16:
00000001 c06330d4 c0633094 00000000 c0680000 c6104000 c6104000 00000000
GPR24:
00000200 00000000 ffffffff 00000004 00000078 00009032 00000000 c62b4c00
NIP [
c02a84bc] mdiobus_read+0x20/0x74
[92708.281517] LR [
c02a947c] kszphy_config_intr+0xa4/0xc4
[92708.286547] Call Trace:
[92708.288980] [
c6105d20] [
c6104000] 0xc6104000 (unreliable)
[92708.294339] [
c6105d40] [
c02a947c] kszphy_config_intr+0xa4/0xc4
[92708.300098] [
c6105d50] [
c02a5330] phy_stop+0x60/0x9c
[92708.305007] [
c6105d60] [
c02c84d0] fs_timeout+0xdc/0x110
[92708.310197] [
c6105d80] [
c035cd48] dev_watchdog+0x268/0x2a0
[92708.315593] [
c6105db0] [
c0060288] call_timer_fn+0x34/0x17c
[92708.321014] [
c6105dd0] [
c00605f0] run_timer_softirq+0x21c/0x2e4
[92708.326887] [
c6105e50] [
c001e19c] __do_softirq+0xf4/0x2f4
[92708.332207] [
c6105eb0] [
c001e3c8] run_ksoftirqd+0x2c/0x40
[92708.337560] [
c6105ec0] [
c003b420] smpboot_thread_fn+0x1f0/0x258
[92708.343405] [
c6105ef0] [
c003745c] kthread+0xbc/0xd0
[92708.348217] [
c6105f40] [
c000c400] ret_from_kernel_thread+0x5c/0x64
[92708.354275] Instruction dump:
[92708.357207]
7c0803a6 bbc10018 38210020 4e800020 7c0802a6 9421ffe0 54290024 bfc10018
[92708.364865]
90010024 7c7f1b78 81290008 552902ee <
0f090000>
3bc3002c 7fc3f378 90810008
[92708.372711] ---[ end trace
42b05441616fafd7 ]---
This patch moves fs_timeout() actions into an async worker.
Fixes: commit
48257c4f168e5 ("Add fs_enet ethernet network driver, for several embedded platforms")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sebastian Andrzej Siewior [Tue, 16 Oct 2018 20:25:25 +0000 (22:25 +0200)]
x86/fpu: Fix i486 + no387 boot crash by only saving FPU registers on context switch if there is an FPU
commit
2224d616528194b02424c91c2ee254b3d29942c3 upstream.
Booting an i486 with "no387 nofxsr" ends with with the following crash:
math_emulate: 0060:
c101987d
Kernel panic - not syncing: Math emulation needed in kernel
on the first context switch in user land.
The reason is that copy_fpregs_to_fpstate() tries FNSAVE which does not work
as the FPU is turned off.
This bug was introduced in:
f1c8cd0176078 ("x86/fpu: Change fpu->fpregs_active users to fpu->fpstate_active")
Add a check for X86_FEATURE_FPU before trying to save FPU registers (we
have such a check in switch_fpu_finish() already).
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes:
f1c8cd0176078 ("x86/fpu: Change fpu->fpregs_active users to fpu->fpstate_active")
Link: http://lkml.kernel.org/r/20181016202525.29437-4-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan Chancellor [Sat, 13 Oct 2018 00:53:12 +0000 (17:53 -0700)]
x86/time: Correct the attribute on jiffies' definition
commit
53c13ba8ed39e89f21a0b98f4c8a241bb44e483d upstream.
Clang warns that the declaration of jiffies in include/linux/jiffies.h
doesn't match the definition in arch/x86/time/kernel.c:
arch/x86/kernel/time.c:29:42: warning: section does not match previous declaration [-Wsection]
__visible volatile unsigned long jiffies __cacheline_aligned = INITIAL_JIFFIES;
^
./include/linux/cache.h:49:4: note: expanded from macro '__cacheline_aligned'
__section__(".data..cacheline_aligned")))
^
./include/linux/jiffies.h:81:31: note: previous attribute is here
extern unsigned long volatile __cacheline_aligned_in_smp __jiffy_arch_data jiffies;
^
./arch/x86/include/asm/cache.h:20:2: note: expanded from macro '__cacheline_aligned_in_smp'
__page_aligned_data
^
./include/linux/linkage.h:39:29: note: expanded from macro '__page_aligned_data'
#define __page_aligned_data __section(.data..page_aligned) __aligned(PAGE_SIZE)
^
./include/linux/compiler_attributes.h:233:56: note: expanded from macro '__section'
#define __section(S) __attribute__((__section__(#S)))
^
1 warning generated.
The declaration was changed in commit
7c30f352c852 ("jiffies.h: declare
jiffies and jiffies_64 with ____cacheline_aligned_in_smp") but wasn't
updated here. Make them match so Clang no longer warns.
Fixes:
7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181013005311.28617-1-natechancellor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra [Thu, 11 Oct 2018 10:38:27 +0000 (12:38 +0200)]
x86/percpu: Fix this_cpu_read()
commit
b59167ac7bafd804c91e49ad53c6d33a7394d4c8 upstream.
Eric reported that a sequence count loop using this_cpu_read() got
optimized out. This is wrong, this_cpu_read() must imply READ_ONCE()
because the interface is IRQ-safe, therefore an interrupt can have
changed the per-cpu value.
Fixes:
7c3576d261ce ("[PATCH] i386: Convert PDA into the percpu section")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: hpa@zytor.com
Cc: eric.dumazet@gmail.com
Cc: bp@alien8.de
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181011104019.748208519@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhimin Gu [Fri, 21 Sep 2018 06:26:24 +0000 (14:26 +0800)]
x86, hibernate: Fix nosave_regions setup for hibernation
commit
cc55f7537db6af371e9c1c6a71161ee40f918824 upstream.
On 32bit systems, nosave_regions(non RAM areas) located between
max_low_pfn and max_pfn are not excluded from hibernation snapshot
currently, which may result in a machine check exception when
trying to access these unsafe regions during hibernation:
[ 612.800453] Disabling lock debugging due to kernel taint
[ 612.805786] mce: [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 6:
fe00000000801136
[ 612.814344] mce: [Hardware Error]: RIP !INEXACT! 60:<
00000000d90be566> {swsusp_save+0x436/0x560}
[ 612.823167] mce: [Hardware Error]: TSC
1f5939fe276 ADDR
dd000000 MISC
30e0000086
[ 612.830677] mce: [Hardware Error]: PROCESSOR 0:306c3 TIME
1529487426 SOCKET 0 APIC 0 microcode 24
[ 612.839581] mce: [Hardware Error]: Run the above through 'mcelog --ascii'
[ 612.846394] mce: [Hardware Error]: Machine check: Processor context corrupt
[ 612.853380] Kernel panic - not syncing: Fatal machine check
[ 612.858978] Kernel Offset: 0x18000000 from 0xc1000000 (relocation range: 0xc0000000-0xf7ffdfff)
This is because on 32bit systems, pages above max_low_pfn are regarded
as high memeory, and accessing unsafe pages might cause expected MCE.
On the problematic 32bit system, there are reserved memory above low
memory, which triggered the MCE:
e820 memory mapping:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000d160cfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d160d000-0x00000000d1613fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000d1614000-0x00000000d1a44fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d1a45000-0x00000000d1ecffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d1ed0000-0x00000000d7eeafff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d7eeb000-0x00000000d7ffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d8000000-0x00000000d875ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d8760000-0x00000000d87fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d8800000-0x00000000d8fadfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d8fae000-0x00000000d8ffffff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000d9000000-0x00000000da71bfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000da71c000-0x00000000da7fffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000da800000-0x00000000dbb8bfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dbb8c000-0x00000000dbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dd000000-0x00000000df1fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041edfffff] usable
Fix this problem by changing pfn limit from max_low_pfn to max_pfn.
This fix does not impact 64bit system because on 64bit max_low_pfn
is the same as max_pfn.
Signed-off-by: Zhimin Gu <kookoo.gu@intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Zijlstra [Thu, 11 Oct 2018 10:38:26 +0000 (12:38 +0200)]
x86/tsc: Force inlining of cyc2ns bits
commit
4907c68abd3f60f650f98d5a69d4ec77c0bde44f upstream.
Looking at the asm for native_sched_clock() I noticed we don't inline
enough. Mostly caused by sharing code with cyc2ns_read_begin(), which
we didn't used to do. So mark all that __force_inline to make it DTRT.
Fixes:
59eaef78bfea ("x86/tsc: Remodel cyc2ns to use seqcount_latch()")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: hpa@zytor.com
Cc: eric.dumazet@gmail.com
Cc: bp@alien8.de
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181011104019.695196158@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Phil Auld [Mon, 8 Oct 2018 14:36:40 +0000 (10:36 -0400)]
sched/fair: Fix throttle_list starvation with low CFS quota
commit
baa9be4ffb55876923dc9716abc0a448e510ba30 upstream.
With a very low cpu.cfs_quota_us setting, such as the minimum of 1000,
distribute_cfs_runtime may not empty the throttled_list before it runs
out of runtime to distribute. In that case, due to the change from
c06f04c7048 to put throttled entries at the head of the list, later entries
on the list will starve. Essentially, the same X processes will get pulled
off the list, given CPU time and then, when expired, get put back on the
head of the list where distribute_cfs_runtime will give runtime to the same
set of processes leaving the rest.
Fix the issue by setting a bit in struct cfs_bandwidth when
distribute_cfs_runtime is running, so that the code in throttle_cfs_rq can
decide to put the throttled entry on the tail or the head of the list. The
bit is set/cleared by the callers of distribute_cfs_runtime while they hold
cfs_bandwidth->lock.
This is easy to reproduce with a handful of CPU consumers. I use 'crash' on
the live system. In some cases you can simply look at the throttled list and
see the later entries are not changing:
crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3
1
ffff90b56cb2d200 -976050
2
ffff90b56cb2cc00 -484925
3
ffff90b56cb2bc00 -658814
4
ffff90b56cb2ba00 -275365
5
ffff90b166a45600 -135138
6
ffff90b56cb2da00 -282505
7
ffff90b56cb2e000 -148065
8
ffff90b56cb2fa00 -872591
9
ffff90b56cb2c000 -84687
10
ffff90b56cb2f000 -87237
11
ffff90b166a40a00 -164582
crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3
1
ffff90b56cb2d200 -994147
2
ffff90b56cb2cc00 -306051
3
ffff90b56cb2bc00 -961321
4
ffff90b56cb2ba00 -24490
5
ffff90b166a45600 -135138
6
ffff90b56cb2da00 -282505
7
ffff90b56cb2e000 -148065
8
ffff90b56cb2fa00 -872591
9
ffff90b56cb2c000 -84687
10
ffff90b56cb2f000 -87237
11
ffff90b166a40a00 -164582
Sometimes it is easier to see by finding a process getting starved and looking
at the sched_info:
crash> task
ffff8eb765994500 sched_info
PID: 7800 TASK:
ffff8eb765994500 CPU: 16 COMMAND: "cputest"
sched_info = {
pcount = 8,
run_delay =
697094208,
last_arrival =
240260125039,
last_queued =
240260327513
},
crash> task
ffff8eb765994500 sched_info
PID: 7800 TASK:
ffff8eb765994500 CPU: 16 COMMAND: "cputest"
sched_info = {
pcount = 8,
run_delay =
697094208,
last_arrival =
240260125039,
last_queued =
240260327513
},
Signed-off-by: Phil Auld <pauld@redhat.com>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes:
c06f04c70489 ("sched: Fix potential near-infinite distribute_cfs_runtime() loop")
Link: http://lkml.kernel.org/r/20181008143639.GA4019@pauld.bos.csb
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikhail Nikiforov [Mon, 15 Oct 2018 18:17:56 +0000 (11:17 -0700)]
Input: elan_i2c - add ACPI ID for Lenovo IdeaPad 330-15IGM
commit
13c1c5e4d7f887cba36c5e3df3faa22071c1469f upstream.
Add ELAN061C to the ACPI table to support Elan touchpad found in Lenovo
IdeaPad 330-15IGM.
Signed-off-by: Mikhail Nikiforov <jackxviichaos@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 15 Oct 2018 20:55:04 +0000 (16:55 -0400)]
USB: fix the usbfs flag sanitization for control transfers
commit
665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream.
Commit
7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes:
7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Tue, 16 Oct 2018 10:16:45 +0000 (12:16 +0200)]
usb: gadget: storage: Fix Spectre v1 vulnerability
commit
9ae24af3669111d418242caec8dd4ebd9ba26860 upstream.
num can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn:
potential spectre issue 'fsg_opts->common->luns' [r] (local cap)
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=
152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuah Khan (Samsung OSG) [Fri, 5 Oct 2018 22:17:44 +0000 (16:17 -0600)]
usb: usbip: Fix BUG: KASAN: slab-out-of-bounds in vhci_hub_control()
commit
81f7567c51ad97668d1c3a48e8ecc482e64d4161 upstream.
vhci_hub_control() accesses port_status array with out of bounds port
value. Fix it to reference port_status[] only with a valid rhport value
when invalid_rhport flag is true.
The invalid_rhport flag is set early on after detecting in port value
is within the bounds or not.
The following is used reproduce the problem and verify the fix:
C reproducer: https://syzkaller.appspot.com/x/repro.c?x=
14ed8ab6400000
Reported-by: syzbot+bccc1fe10b70fadc78d0@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Thu, 4 Oct 2018 13:49:06 +0000 (15:49 +0200)]
cdc-acm: fix race between reset and control messaging
commit
9397940ed812b942c520e0c25ed4b2c64d57e8b9 upstream.
If a device splits up a control message and a reset() happens
between the parts, the message is lost and already recieved parts
must be dropped.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes:
1aba579f3cf51 ("cdc-acm: handle read pipe errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tobias Herzog [Sat, 22 Sep 2018 20:11:11 +0000 (22:11 +0200)]
cdc-acm: correct counting of UART states in serial state notification
commit
f976d0e5747ca65ccd0fb2a4118b193d70aa1836 upstream.
The usb standard ("Universal Serial Bus Class Definitions for Communication
Devices") distiguishes between "consistent signals" (DSR, DCD), and
"irregular signals" (break, ring, parity error, framing error, overrun).
The bits of "irregular signals" are set, if this error/event occurred on
the device side and are immeadeatly unset, if the serial state notification
was sent.
Like other drivers of real serial ports do, just the occurence of those
events should be counted in serial_icounter_struct (but no 1->0
transitions).
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tobias Herzog [Sat, 22 Sep 2018 20:11:10 +0000 (22:11 +0200)]
cdc-acm: do not reset notification buffer index upon urb unlinking
commit
dae3ddba36f8c337fb59cef07d564da6fc9b7551 upstream.
Resetting the write index of the notification buffer on urb unlink (e.g.
closing a cdc-acm device from userspace) may lead to wrong interpretation
of further received notifications, in case the index is not 0 when urb
unlink happens (i.e. when parts of a notification already have been
transferred). On the device side there is no "reset" of the notification
transimission and thus we would get out of sync with the device.
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Tue, 16 Oct 2018 14:32:40 +0000 (16:32 +0200)]
IB/ucm: Fix Spectre v1 vulnerability
commit
0295e39595e1146522f2722715dba7f7fba42217 upstream.
hdr.cmd can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/infiniband/core/ucm.c:1127 ib_ucm_write() warn: potential
spectre issue 'ucm_cmd_table' [r] (local cap)
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=
152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Tue, 16 Oct 2018 14:59:01 +0000 (16:59 +0200)]
RDMA/ucma: Fix Spectre v1 vulnerability
commit
a3671a4f973ee9d9621d60166cc3b037c397d604 upstream.
hdr.cmd can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/infiniband/core/ucma.c:1686 ucma_write() warn: potential
spectre issue 'ucma_cmd_table' [r] (local cap)
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=
152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugeniy Paltsev [Wed, 3 Oct 2018 16:45:38 +0000 (19:45 +0300)]
drm: fb-helper: Reject all pixel format changing requests
commit
db05c481977599236f12a85e55de9f5ab37b0a2c upstream.
drm fbdev emulation doesn't support changing the pixel format at all,
so reject all pixel format changing requests.
Cc: stable@vger.kernel.org
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181003164538.5534-1-Eugeniy.Paltsev@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clint Taylor [Fri, 5 Oct 2018 21:52:15 +0000 (14:52 -0700)]
drm/edid: VSDB yCBCr420 Deep Color mode bit definitions
commit
9068e02f58740778d8270840657f1e250a2cc60f upstream.
HDMI Forum VSDB YCBCR420 deep color capability bits are 2:0. Correct
definitions in the header for the mask to work correctly.
Fixes:
e6a9a2c3dc43 ("drm/edid: parse ycbcr 420 deep color information")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107893
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1538776335-12569-1-git-send-email-clinton.a.taylor@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kai-Heng Feng [Tue, 2 Oct 2018 15:29:11 +0000 (23:29 +0800)]
drm/edid: Add 6 bpc quirk for BOE panel in HP Pavilion 15-n233sl
commit
0711a43b6d84ff9189adfbf83c8bbf56eef794bf upstream.
There's another panel that reports "DFP 1.x compliant TMDS" but it
supports 6bpc instead of 8 bpc.
Apply 6 bpc quirk for the panel to fix it.
BugLink: https://bugs.launchpad.net/bugs/1794387
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181002152911.4370-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gustavo A. R. Silva [Tue, 16 Oct 2018 13:06:41 +0000 (15:06 +0200)]
ptp: fix Spectre v1 vulnerability
commit
efa61c8cf2950ab5c0e66cff3cabe2a2b24e81ba upstream.
pin_index can be indirectly controlled by user-space, hence leading
to a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/ptp/ptp_chardev.c:253 ptp_ioctl() warn: potential spectre issue
'ops->pin_config' [r] (local cap)
Fix this by sanitizing pin_index before using it to index
ops->pin_config, and before passing it as an argument to
function ptp_set_pinfunc(), in which it is used to index
info->pin_config.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=
152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro [Wed, 17 Oct 2018 14:23:26 +0000 (15:23 +0100)]
cachefiles: fix the race between cachefiles_bury_object() and rmdir(2)
commit
169b803397499be85bdd1e3d07d6f5e3d4bd669e upstream.
the victim might've been rmdir'ed just before the lock_rename();
unlike the normal callers, we do not look the source up after the
parents are locked - we know it beforehand and just recheck that it's
still the child of what used to be its parent. Unfortunately,
the check is too weak - we don't spot a dead directory since its
->d_parent is unchanged, dentry is positive, etc. So we sail all
the way to ->rename(), with hosting filesystems _not_ expecting
to be asked renaming an rmdir'ed subdirectory.
The fix is easy, fortunately - the lock on parent is sufficient for
making IS_DEADDIR() on child safe.
Cc: stable@vger.kernel.org
Fixes:
9ae326a69004 (CacheFiles: A cache that backs onto a mounted filesystem)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian Foster [Sat, 3 Nov 2018 17:15:24 +0000 (19:15 +0200)]
xfs: truncate transaction does not modify the inobt
[ Upstream commit
a606ebdb859e78beb757dfefa08001df366e2ef5 ]
The truncate transaction does not ever modify the inode btree, but
includes an associated log reservation. Update
xfs_calc_itruncate_reservation() to remove the reservation
associated with inobt updates.
[Amir: This commit was merged for kernel v4.16 and a twin commit was
merged for xfsprogs v4.16. As a result, a small xfs filesystem
formatted with features -m rmapbt=1,reflink=1 using mkfs.xfs
version >= v4.16 cannot be mounted with kernel < v4.16.
For example, xfstests generic/17{1,2,3} format a small fs and
when trying to mount it, they fail with an assert on this very
demonic line:
XFS (vdc): Log size 3075 blocks too small, minimum size is 3717 blocks
XFS (vdc): AAIEEE! Log failed size checks. Abort!
XFS: Assertion failed: 0, file: src/linux/fs/xfs/xfs_log.c, line: 666
The simple solution for stable kernels is to apply this patch,
because mkfs.xfs v4.16 is already in the wild, so we have to
assume that xfs filesystems with a "too small" log exist.
Regardless, xfsprogs maintainers should also consider reverting
the twin patch to stop creating those filesystems for the sake
of users with unpatched kernels.]
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Darrick J . Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Linus Walleij [Wed, 29 Aug 2018 15:02:16 +0000 (17:02 +0200)]
gpio: mxs: Get rid of external API call
[ Upstream commit
833eacc7b5913da9896bacd30db7d490aa777868 ]
The MXS driver was calling back into the GPIO API from
its irqchip. This is not very elegant, as we are a driver,
let's just shortcut back into the gpio_chip .get() function
instead.
This is a tricky case since the .get() callback is not in
this file, instead assigned by bgpio_init(). Calling the
function direcly in the gpio_chip is however the lesser
evil.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Amir Goldstein [Sat, 1 Sep 2018 06:40:01 +0000 (09:40 +0300)]
fsnotify: fix ignore mask logic in fsnotify()
[ Upstream commit
9bdda4e9cf2dcecb60a0683b10ffb8cd7e5f2f45 ]
Commit
92183a42898d ("fsnotify: fix ignore mask logic in
send_to_group()") acknoledges the use case of ignoring an event on
an inode mark, because of an ignore mask on a mount mark of the same
group (i.e. I want to get all events on this file, except for the events
that came from that mount).
This change depends on correctly merging the inode marks and mount marks
group lists, so that the mount mark ignore mask would be tested in
send_to_group(). Alas, the merging of the lists did not take into
account the case where event in question is not in the mask of any of
the mount marks.
To fix this, completely remove the tests for inode and mount event masks
from the lists merging code.
Fixes:
92183a42898d ("fsnotify: fix ignore mask logic in send_to_group")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
[amir: backport to v4.14.y]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sasha Levin [Tue, 6 Nov 2018 06:23:39 +0000 (01:23 -0500)]
Revert "ARM: tegra: Fix ULPI regression on Tegra20"
This reverts commit
b39ac54215190bc178ae7de799e74d327a3c1a33.
The issue was fixed by upstream commit
5d797111afe1 ("clk:
tegra: Add quirk for getting CDEV1/2 clocks on Tegra20").
Signed-off-by: Sasha Levin <sashal@kernel.org>
Daniel Borkmann [Thu, 1 Nov 2018 21:30:38 +0000 (22:30 +0100)]
bpf: fix partial copy of map_ptr when dst is scalar
commit
0962590e553331db2cc0aef2dc35c57f6300dbbe upstream.
ALU operations on pointers such as scalar_reg += map_value_ptr are
handled in adjust_ptr_min_max_vals(). Problem is however that map_ptr
and range in the register state share a union, so transferring state
through dst_reg->range = ptr_reg->range is just buggy as any new
map_ptr in the dst_reg is then truncated (or null) for subsequent
checks. Fix this by adding a raw member and use it for copying state
over to dst_reg.
Fixes:
f1174f77b50c ("bpf/verifier: rework value tracking")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / platform / kernel / linux-exynos.git / log