Ying Zhang [Fri, 24 Jan 2014 07:50:06 +0000 (15:50 +0800)]
SPL: powerpc: expand SPL's length to 128K
1. The SPL's length of SDCARD boot has not enough,expand the SPL's
length to 128K.
2. deleted unused symbol: CONFIG_SYS_RUN_INDDR
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 21 Feb 2014 05:16:19 +0000 (13:16 +0800)]
powerpc/t2081qds: Add T2081 QDS board support
T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.
T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
- Two on-board 10M/100M/1G bps RGMII ports
- Two 10Gbps XFI with on-board SFP+ cage
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
- Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
- 8 lanes up to 10.3125GHz
- Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
- 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
- Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
voltage translators
- I2C:
- Four I2C controllers.
- UART:
- Dual 4-pins UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Tue, 21 Jan 2014 06:11:47 +0000 (14:11 +0800)]
powerpc/t208x: some update to support t2081
- fix serdes definition for t2081.
- fix clock speed for t2081.
- update ids, as CONFIG_FSL_SATA_V2 is needed only for t2080,
T2081 has no SATA.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alexey Brodkin [Fri, 13 Dec 2013 06:35:11 +0000 (10:35 +0400)]
serial/serial_arc - add driver for ARC UART
Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys)
FPGA Boards such as ARCAngel4/ML50x
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Tom Rini [Fri, 7 Feb 2014 13:52:06 +0000 (08:52 -0500)]
x600: Switch to CONFIG_PHYLIB
Now that the designware ethernet driver uses phylib we need to turn it
on here.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Alexey Brodkin [Wed, 22 Jan 2014 16:49:09 +0000 (20:49 +0400)]
net/designware: make driver compatible with data cache
Up until now this driver only worked with data cache disabled.
To make it work with enabled data cache following changes were required:
* Flush Tx/Rx buffer descriptors their modification
* Invalidate Tx/Rx buffer descriptors before reading its values
* Flush cache for data passed from CPU to GMAC
* Invalidate cache for data passed from GMAC to CPU
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Wed, 22 Jan 2014 16:54:06 +0000 (20:54 +0400)]
net/designware - switch driver to phylib usage
With this change driver will benefit from existing phylib and thus
custom phy functionality implemented in the driver will go away:
* Instantiation of the driver is now much shorter - 2 parameters
instead of 4.
* Simplified phy management/functoinality in driver is replaced with
rich functionality of phylib.
* Support of custom phy initialization is now done with existing
"board_phy_config".
Note that after this change some previously used config options
(driver-specific PHY configuration) will be obsolete and they are simply
substituted with similar options of phylib.
For example:
* CONFIG_DW_AUTONEG - no need in this one. Autonegotiation is enabled
by default.
* CONFIG_DW_SEARCH_PHY - if one wants to specify attached phy
explicitly CONFIG_PHY_ADDR board config option has to be used, otherwise
automatically the first discovered on MDIO bus phy will be used
I believe there's no need now in "doc/README.designware_eth" because
user only needs to instantiate the driver with "designware_initialize"
whose prototype exists in "include/netdev.h".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Fri, 10 Jan 2014 15:58:11 +0000 (19:58 +0400)]
net: execute "miiphy_init" if CONFIG_PHYLIB defined
In "common/Makefile" "miiphyutil.o" gets built if any of the following
items enabled:
* CONFIG_PHYLIB
* CONFIG_MII
* CONFIG_CMD_MII
So it's possible to not define CONFIG_MII or CONFIG_CMD_MII and still
use functions like "miiphy_get_dev_by_name".
In its turn "miiphy_get_dev_by_name" traverses "mii_devs" list which is
not initialized because "miiphy_init" never got called.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Mon, 13 Jan 2014 09:28:38 +0000 (13:28 +0400)]
net/designware: add explicit reset of {tx|rx}_currdescnum
Driver "init" function might be called multiple times.
On every "init" Tx/Rx buffer descriptors are initialized: "descs_init"
-> "{tx|rx}_descs_init".
In its turn those init functions set MAC's "{tx|rx}desclistaddr" to
point on the first buffer descriptor in the list.
So CPU to start operation from the first buffer descriptor as well after
every "init" we have to reset "{tx|rx}_currdescnum".
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Mischa Jonker <mjonker@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:21 +0000 (12:56 +0400)]
arc: add README for architecture
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:20 +0000 (12:56 +0400)]
arc: add architecture to MAKEALL
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:19 +0000 (12:56 +0400)]
arc: add AXS101 board support
AXS101 is a new generation of devlopment boards from Synopsys that houses
ASIC with ARC700 and lots of DesignWare peripherals:
* DW APB UART
* DW Mobile Storage (MMC/SD)
* DW I2C
* DW GMAC
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:18 +0000 (12:56 +0400)]
arc: add Arcangel4 board support
Arcangel4 is a FPGA-based development board that is used for prototyping and
verificationof of both ARC hardware (CPUs) and software running upon CPU.
This board avaialble in 2 flavours:
* Little-endian (arcangel4)
* Big-endian (arcangel4-be)
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:17 +0000 (12:56 +0400)]
arc: add support for standalone programs
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:16 +0000 (12:56 +0400)]
arc: bdinfo, image and arc-specific init functions declarations support
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:15 +0000 (12:56 +0400)]
arc: add library functions
These are library functions used by ARC700 architecture.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:14 +0000 (12:56 +0400)]
arc: add cpu files
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Alexey Brodkin [Tue, 4 Feb 2014 08:56:13 +0000 (12:56 +0400)]
arc: add architecture header files
These are header files used by ARC700 architecture.
Also note that "arch-arc700/hardware.h" is only required for compilation of
"designware_i2c" driver which refers to "asm/arch/hardware.h".
It would be good to fix mentioned driver sometime soon but it will cause
changes in ARM board configs that use "designware_i2c".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Aaron Wu [Wed, 23 Nov 2011 03:23:56 +0000 (11:23 +0800)]
blackfin: Initialize the EMAC VLAN with proper default value
EMAC_VLANx regs is not properly initiallized in u-boot, once it's overwrite in the
kernel when DSA enabled, hot reset will lead to bringing up EMAC fail in u-boot.
Signed-off-by: Aaron Wu <Aaron.Wu@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Sonic Zhang [Wed, 22 Jan 2014 08:04:19 +0000 (16:04 +0800)]
blackfin: Change SMC dcplb entry flag to cover 16M address region
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Bob Liu [Tue, 27 Sep 2011 03:00:27 +0000 (11:00 +0800)]
blackfin: init bss early
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Sonic Zhang [Wed, 22 Jan 2014 07:43:25 +0000 (15:43 +0800)]
blackfin: The logic of the BF609 macro is opposite.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Tom Rini [Thu, 6 Feb 2014 19:26:05 +0000 (14:26 -0500)]
include/usb/s3c_udc.h: Add <asm/sizes.h>
With e0059ea switching to using SZ_1K, we need to #include <asm/sizes.h>
here for everyone to build still.
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 6 Feb 2014 16:20:23 +0000 (11:20 -0500)]
Merge branch 'fpga' of git://denx.de/git/u-boot-microblaze
Michal Simek [Thu, 26 Sep 2013 14:39:03 +0000 (16:39 +0200)]
fpga: zynqpl: Add support for zc7015 device
Just extend tables with this new device.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Novasys Ingenierie [Wed, 27 Nov 2013 08:03:01 +0000 (09:03 +0100)]
fpga: zynq: Correct fpga load when buf is not aligned
When ARCH_DMA_MINALIGN is greater than header size of the bit file, and buf is
not aligned, new_buf address became greater then buf_start address and the
load_word loop corrupts bit file data.
A work around is to decrease new_buf of ARCH_DMA_MINALIGN, it might corrupt data
before buf but permits to load correctly.
Signed-off-by: Stany MARCEL <smarcel@novasys-ingenierie.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Marek Vasut [Thu, 6 Feb 2014 01:43:45 +0000 (02:43 +0100)]
usb: mv_udc: Rename to ci_udc
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:46 +0000 (10:10 +0100)]
usb:gadget:f_thor: cosmetic: Remove debug memset
Apparently debug memset (with a 0x55 value) has been overlooked in the
f_thor code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:45 +0000 (10:10 +0100)]
usb:gadget:f_thor: Allocate request up to THOR_PACKET_SIZE not ep->maxpacket
Now it is possible to allocate static request - which receives data from
the host (OUT transaction) to the size of THOR packet.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:44 +0000 (10:10 +0100)]
usb:udc:samsung: Zero copy approach for data passed to Samsung's UDC driver
The Samsung's UDC driver is not anymore copying data from USB requests to
aligned internal buffers. Now it works directly in data allocated in the
upper layers like UMS, DFU, THOR.
This change is possible since those gadgets now must take care to allocate
buffers aligned to cache line (CONFIG_SYS_CACHELINE_SIZE).
This can be achieved by using DEFINE_CACHE_ALIGN_BUFFER() or
ALLOC_CACHE_ALIGN_BUFFER() macros. Those take care to allocate buffer
aligned to cache line in both starting address and its size.
Sometimes it is enough to just use memalign() with size being a
multiplication of cache line size.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 27.04 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:43 +0000 (10:10 +0100)]
usb:udc:samsung: Allow burst transfers for non EP0 endpints
This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.
Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 20.74 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:42 +0000 (10:10 +0100)]
usb:udc:samsung: Remove redundant cache operation from Samsung UDC driver
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:
1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)
2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.
Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.
3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurements:
Base values (without improvement):
Transmission speed: 9.51 MiB/s
After the change:
Transmission speed: 10.15 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Wed, 5 Feb 2014 09:10:41 +0000 (10:10 +0100)]
usb:gadget:ums: Replace malloc calls with memalign to fix cache buffer alignment
Calls to malloc() have been replaced by memalign. It now provides proper
buffer alignment.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Tom Rini [Wed, 5 Feb 2014 13:04:38 +0000 (08:04 -0500)]
config: Fix line lengths in include/config_distro_defaults.h
Signed-off-by: Tom Rini <trini@ti.com>
Dennis Gilmore [Tue, 4 Feb 2014 11:25:47 +0000 (05:25 -0600)]
config: add config_distro_defaults.h
describe a set of default features that distros can rely on being available.
having this common definition means that distros can easily support systems
implementing them.
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Dennis Gilmore [Tue, 4 Feb 2014 11:25:46 +0000 (05:25 -0600)]
cmd_pxe.c add any option for filesystem with sysboot uses generic load
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Tom Rini [Tue, 4 Feb 2014 16:48:48 +0000 (11:48 -0500)]
Merge branch 'serial' of git://denx.de/git/u-boot-microblaze
Tom Rini [Tue, 4 Feb 2014 16:48:39 +0000 (11:48 -0500)]
Merge branch 'net' of git://denx.de/git/u-boot-microblaze
Tom Rini [Tue, 4 Feb 2014 16:48:25 +0000 (11:48 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-microblaze
Tom Rini [Tue, 4 Feb 2014 16:48:14 +0000 (11:48 -0500)]
Merge branch 'clk' of git://denx.de/git/u-boot-microblaze
Tom Rini [Tue, 4 Feb 2014 15:22:23 +0000 (10:22 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Stephen Warren [Tue, 28 Jan 2014 21:50:10 +0000 (14:50 -0700)]
pxe: implement fdtdir extlinux.conf tag
People who write (or scripts that auto-generate) extlinux.conf don't
want to know about HW-specific information such as FDT filenames. Create
a new extlinux.conf tag "fdtdir" that specifies only the directory where
FDT files are located, and defer all knowledge of the filename to U-Boot.
The algorithm implemented is:
==========
if $fdt_addr_r is set:
if "fdt" tag was specified in extlinux.conf:
load the FDT from the filename in the tag
else if "fdtdir" tag was specified in extlinux.conf:
if "fdtfile" is set in the environment:
load the FDT from filename in "$fdtfile"
else:
load the FDT from some automatically generated filename
if no FDT file was loaded, and $fdtaddr is set:
# This indicates an FDT packaged with firmware
use the FDT at $fdtaddr
==========
A small part of an example /boot/extlinux.conf might be:
==========
LABEL primary
LINUX zImage
FDTDIR ./
LABEL failsafe
LINUX bkp/zImage
FDTDIR bkp/
==========
... with /boot/tegra20-seaboard.dtb or /boot/bkp/tegra20-seaboard.dtb
being loaded by the sysboot/pxe code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Tue, 28 Jan 2014 21:50:09 +0000 (14:50 -0700)]
pxe: support "devicetree" tag
The specification for extlinux.conf[1] states that "fdt" is an alias for
"devicetree". To date, U-Boot only implements "fdt". Rectify that.
[1] http://freedesktop.org/wiki/Specifications/BootLoaderSpec/
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Michal Simek [Tue, 21 Jan 2014 06:29:47 +0000 (07:29 +0100)]
serial: uartlite: Reset RX/TX in init
Just to be sure that there is no pending data.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 21 Nov 2013 15:15:51 +0000 (16:15 +0100)]
net: axi_emac: Check if phy was correctly detected
As tsec and fm drivers checking phydev->link
ensure that u-boot don't try access device if link is not ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 21 Jan 2014 06:30:37 +0000 (07:30 +0100)]
microblaze: Add SPL support
Add support for U-BOOT SPL. NOR and RAM mode are supported.
There are 3 images in NOR flash. u-boot.img, dtb and kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Tue, 21 Jan 2014 06:26:58 +0000 (07:26 +0100)]
microblaze: Enable buffer write for NOR flashes
It speeds up writing a lot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 20 Jan 2014 20:17:07 +0000 (21:17 +0100)]
microblaze: Report priviledged or stack protection exception
Just list one more exception.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Mon, 20 Jan 2014 20:05:47 +0000 (21:05 +0100)]
microblaze: Show u-boot banner
It is nice to see u-boot version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 21 Nov 2013 21:39:02 +0000 (13:39 -0800)]
common: Add new clk command
Command provides just dump subcommand for showing clock
frequencies in a soc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Prabhakar Kushwaha [Sat, 18 Jan 2014 06:58:30 +0000 (12:28 +0530)]
driver/ifc:Change accessor function to take care of endianness
IFC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of IFC IP.
So update acessor functions with common IFC acessor functions to take care
both type of endianness.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:12 +0000 (11:49 +0100)]
kmp204x: initial support for PCIe FPGA configuration
The PEXHC PCIe configuration mechanism ensures that the FPGA get
configured at power-up. Since all the PCIe devices should be configured
when the kernel start, u-boot has to take care that the FPGA gets
configured also in other reset scenarios, mostly because of possible
configuration change.
The used mechanism is taken from the km_kirkwood design and adapted to
the kmp204x case (slightly different HW and PCIe configuration).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:11 +0000 (11:49 +0100)]
kmp204x: enable support for SPANSION SPI NOR
The new prototype and the final series was moved from Micron to Spansion
to have a better reset sequence that is easier to support.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:10 +0000 (11:49 +0100)]
KM: add the KM_UBI_PART_BOOT_OPTS #define
This define can be used if the ubi boot partition (defined for all
Keymile boards with KM_UBI_PARTITION_NAME_BOOT #define to ubi0) needs
some additionnal boot options.
This is the case for the kmp204x boards since u-boot does not support
NAND Flash subpage accesses on this platform, an additionnal argument
that defines the VID offstet must be given to the kernel.
The UBI cmd line option now looks like this "ubi.mtd=ubi0,2048" on this
platform.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:09 +0000 (11:49 +0100)]
kmp204x: update I2C field of RCW
On the previous HW revision (now unsupported), there was a need for
external DMA signals and thus the I2C3/4 signals were used
DMA1_DONE/ACK/REQ.
These signals now are configured as GPIO[16:19].
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:08 +0000 (11:49 +0100)]
kmp204x: add support for the kmcoge4 board
The kmcoge4 board is the product board derived from the kmlion1
prototype. The main difference between the 2 boards is that the kmcoge4
does not configure the Local Bus controller for LCS2.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to boards.cfg to keep targets in order]
Signed-off-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:07 +0000 (11:49 +0100)]
kmp204x: implement workaround for A-006559
According to the errata, some bits of an undocumented register in the
DCSR must be set for every core in order to avoid a possible data or
instruction corruption.
This is required for the 2.0 revision of the P2041 that should be used
as soon as available in our design.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Rainer Boschung [Mon, 3 Feb 2014 07:45:40 +0000 (08:45 +0100)]
kmp204x: I2C deblocking support
This patch adds support for using some GPIOs that are connected to the
I2C bus to force the bus lines state and perform some bus deblocking
sequences.
The KM common deblocking algorithm from board/keymile/common/common.c is
used. The GPIO lines used for deblocking the I2C bus are some external
GPIOs provided by the QRIO CPLD:
- SCL = GPIOA_20
- SDA = GPIOA_21
The QRIO GPIOs act in an open-drain-like manner, for 0 the line is
driven low and for 1 the GPIO is set as input and the line gets
pulled-up.
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Valentin Longchamp [Mon, 27 Jan 2014 10:49:05 +0000 (11:49 +0100)]
kmp204x: introduce QRIO GPIO functions
The QRIO GPIO functions can be of general interest. They are thus added
to a qrio.c and their prototype are available from kmp204x.h. The QRIO
prst function are also included in this file, as well as the functions
required for the I2C deblocking support (open-drain).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Remove extra blank line in board/keymile/kmp204x/qrio.c]
Signed-off-by: York Sun <yorksun@freescale.com>
Rainer Boschung [Mon, 27 Jan 2014 10:49:04 +0000 (11:49 +0100)]
kmp204x: support for QRIO1 bootcounter
Make use of the QRIO1 32bit register at 0x20 as bootcounter register
Check for BOOTCOUNT_MAGIC pattern when before bootcounter value is read
Signed-off-by: Rainer Boschung <rainer.boschung@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Thu, 30 Jan 2014 06:00:04 +0000 (11:30 +0530)]
powerpc/t104xrdb: Add basic ethernet support
This covers only non-L2 switch ethernet interfaces i.e.
RGMII and SGMII interface for both T1040RDB and T1042RDB_PI
T1040RDB is configured as serdes protocol 0x66 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
1 SGMII on DTSEC3
T1042RDB_PI is configured as serdes protocol 0x06 which can
support following interfaces
2 RGMIIS on DTSEC4, DTSEC5
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change in commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Nikhil Badola [Mon, 27 Jan 2014 09:51:58 +0000 (15:21 +0530)]
powerpc/usb: Enable dual phy for T1040
Define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE macro for enabling dual
phy in t1040
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Mon, 27 Jan 2014 09:11:55 +0000 (14:41 +0530)]
powerpc/t104xrdb: Update T1042RDB.h in config folder
Add usb2 node entry to hwconfig default
Remove DDR controller interleaving from hwconfig
Move SPI related macros out of "#ifdef CONFIG_SPIFLASH"
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible in u-boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Fix commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Priyanka Jain [Mon, 27 Jan 2014 08:37:11 +0000 (14:07 +0530)]
powerpc/t104xrdb: Update T1040RDB.h in config folder
Add usb2 node entry in "hwconfig string"
Remove controller interleaving from hwconfig string as T1040
has only one DDR conroller
SPI related macros which were earlier under #ifdef CONFIG_SPIFLASH
are move outside so that they are defined for all cases as these
macros are also used by other u-boot code
Add CONFIG_SYS_CSPR2_EXT to make CPLD accessible
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
[York Sun: Minor change to commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Mon, 27 Jan 2014 10:25:20 +0000 (15:55 +0530)]
boards/t1040qds: Adds ethernet support for T1040
Enable entherent for T1040QDS. It enables FM1@DTSEC3, FM1@DTSEC4, FM1@DTSEC5
Define MDIO related configs
Added eth.c file
Update t1040.c to support RGMII and SGMII
Update t1040qds.c to support ethernet
Define the PHY address
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: remove dash from commit message]
Signed-off-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Fri, 24 Jan 2014 12:21:50 +0000 (17:51 +0530)]
powerpc/mpc85xx: Update serdes protocols for T1040
T1040 has only one SerDes block. so update the code accordingly.
Also, add support of SerDes Protocol 0x00, 0x06, 0x40, 0x69 0x85,
0xA7 and 0xAA
Signed-off-by: Arpit Goel <B44344@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Sat, 25 Jan 2014 06:41:23 +0000 (12:11 +0530)]
powerpc/mpc85xx:Fix README to show correct flash memory map
Due to increased size of u-boot, FMAN ucode start address has been shifted
by 256KB causing a overlap with rootfs start address.
Update rootfs start address to reflect correct memory map.
Also fix minor typo in README
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Prabhakar Kushwaha [Sat, 25 Jan 2014 07:23:32 +0000 (12:53 +0530)]
driver/fsl_pci:Update print to display PCIe generation
Current print only display width of PCIe device. Add print to display
PCIe generation supported by the device.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
poonam aggrwal [Thu, 23 Jan 2014 20:54:59 +0000 (02:24 +0530)]
powerpc/mpc85xx: Update LIODNs for T1040
Removed LIODNs for RMAN, RIO, 10G. T1040 has 10 QMAN portals so assigned
LIODNs accordingly.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Ezequiel Garcia [Tue, 28 Jan 2014 10:19:06 +0000 (07:19 -0300)]
board: nios2: Check if flash is configured before calling early_flash_cmd_reset()
If CONFIG_CFI_FLASH_MTD is not defined, then we shouldn't perform the
flash early reset.
This commit fixes the following build error:
nios2-generic.c: In function `__early_flash_cmd_reset':
nios2-generic.c:23: error: `AMD_CMD_RESET' undeclared (first use in this function)
nios2-generic.c:23: error: (Each undeclared identifier is reported only once
nios2-generic.c:23: error: for each function it appears in.)
nios2-generic.c:24: error: `FLASH_CMD_RESET' undeclared (first use in this function)
which was introduced by:
commit
a113fb39df43546c704aa8eba55720da9a9dfedd
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Fri Dec 20 18:34:53 2013 -0300
board: nios2: Add CONFIG_CFI_FLASH_MTD guard to flash.h header include
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Reported-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Masahiro Yamada [Tue, 26 Nov 2013 07:13:59 +0000 (16:13 +0900)]
sandbox: Use system headers first for sandbox's os.c in a different way
Commit
cbe5cdfcd changed config.mk and arch/sandbox/cpu/Makefile
to use -idirafter instead of -I and remove -nostdinc.
But
* Sandbox-specific code dirties config.mk
* os.c is compiled without such compiler flags as:
-Wall -Wstrict-prototypes -Wno-format-security
-fno-builtin -ffreestanding -fno-stack-protector
-fstack-usage -Wno-format-nonliteral
This commit use -idirafter and remove the -nostdinc
differently and more simply.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
rick [Fri, 24 Jan 2014 09:14:28 +0000 (17:14 +0800)]
nds32: add support for leopard and orca board boot flow auto detect
hardware difference between leopard and orca as below:
flash setting leoaprd orca
bank size 32MB 64MB
bus width 32-bits 16-bits
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Kuan-Yu Kuo <ken.kuoky@gmail.com>
Fabio Estevam [Sat, 25 Jan 2014 20:42:39 +0000 (18:42 -0200)]
boards.cfg: Keep the entries sorted
Run "tools/reformat.py -i -d '-' -s 8 <boards.cfg >boards0.cfg && mv boards0.cfg boards.cfg"
in order to keep the entries sorted.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Alexey Brodkin [Mon, 20 Jan 2014 10:30:39 +0000 (14:30 +0400)]
board_r - fixup functions table after relocation
This is only required for "PIC" relocation and doesn't apply to modern
"PIE" relocation which does data relocation as well as code.
"init_sequence_r" is just an array that consists of compile-time
adresses of init functions. Since this is basically an array of integers
(pointers to "void" to be more precise) it won't be modified during
relocation - it will be just copied to new location as it is.
As a consequence on execution after relocation "initcall_run_list" will
be jumping to pre-relocation addresses. As long as we don't overwrite
pre-relocation memory area init calls are executed correctly. But still
it is dangerous because after relocation we don't expect initially used
memory to stay untouched.
Cc: Tom Rini <trini@ti.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Thomas Langer <thomas.langer@lantiq.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Dan Murphy [Thu, 16 Jan 2014 17:23:31 +0000 (11:23 -0600)]
arm: am43xx: Add USB spl boot support
Add the USB host boot support for the am43xx evm
Add the macros to boot from a usb drive in uBoot
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 16 Jan 2014 17:23:30 +0000 (11:23 -0600)]
spl: common: Support for USB MSD FAT image loading
Add SPL support to be able to detect a USB Mass Storage device
connected to a USB host. Once a USB Mass storage device is detected
the SPL will load the u-boot.img from a FAT partition to target address.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Dan Murphy [Thu, 16 Jan 2014 17:23:29 +0000 (11:23 -0600)]
spl: common: Move FAT funcs to a common file
Move the FAT functions to a common location for reuse.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Masahiro Yamada [Thu, 16 Jan 2014 02:03:07 +0000 (11:03 +0900)]
powerpc: mpc5xxx: remove redundant CONFIG_MPC5xxx definition
We do not have to define CONFIG_MPC5xxx in board config headers
(and start.S) because it is defined in arch/powerpc/cpu/mpc5xxx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 09:00:25 +0000 (18:00 +0900)]
board: delete meaningless serial.h
Delete some serial.h files, whole code in which is surrounded by
#if 0 ... #endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Masahiro Yamada [Wed, 15 Jan 2014 04:06:41 +0000 (13:06 +0900)]
sandbox: fix the return type of os_free() function
The function os_free() returns nothing.
Its return type should be "void" rather than "void *".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 02:00:45 +0000 (11:00 +0900)]
ARM: merge commonly-defined PLATFORM_RELFLAGS
Before this commit, all arch/arm/cpu/${CPU}/config.mk except ARMv8
had the same option:
$(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,))
This commit moves it into arch/arm/config.mk.
If the compiler does not support the option,
it is ignored by $(call cc-option,...).
So this commit gives no harm to ARMv8.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 01:14:21 +0000 (10:14 +0900)]
powerpc: mpc86xx: move CONFIG_MPC86xx definition to CPU config.mk
Define CONFIG_MPC86xx in arch/powerpc/cpu/mpc86xx/config.mk
because all target boards with mpc86xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 01:14:07 +0000 (10:14 +0900)]
powerpc: mpc85xx: move CONFIG_MPC85xx definition to CPU config.mk
Define CONFIG_MPC85xx in arch/powerpc/cpu/mpc85xx/config.mk
because all target boards with mpc85xx cpu define it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 01:13:49 +0000 (10:13 +0900)]
powerpc: mpc824x: remove redundant CONFIG_MPC824X definition
We do not have to define CONFIG_MPC824X in board config headers
because it is defined in arch/powerpc/cpu/mpc824x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 01:13:00 +0000 (10:13 +0900)]
powerpc: mpc5xx: remove redundant CONFIG_5xx definition
We do not have to define CONFIG_5xx in a source file
because it is defined in arch/powerpc/cpu/mpc5xx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 15 Jan 2014 01:11:28 +0000 (10:11 +0900)]
powerpc: mpc512x: remove redundant CONFIG_MPC512X definition
We do not have to define CONFIG_MPC512X in board config headers
because it is defined in arch/powerpc/cpu/mpc512x/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 14 Jan 2014 08:26:43 +0000 (17:26 +0900)]
powerpc: mpc8xx: remove redundant CONFIG_8xx definition
We do not have to define CONFIG_8xx in source files
because it is defined in arch/powerpc/cpu/mpc8xx/config.mk
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 14 Jan 2014 08:26:17 +0000 (17:26 +0900)]
powerpc: mpc83xx: remove redundant CONFIG_MPC83xx definition
We do not have to define CONFIG_MPC83xx in board config headers
because it is defined in arch/powerpc/cpu/mpc83xx/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 14 Jan 2014 08:24:35 +0000 (17:24 +0900)]
powerpc: ppc4xx: remove redundant CONFIG_4xx definition
We do not have to define CONFIG_4xx in board config headers
because it is defined in arch/powerpc/cpu/ppc4xx/config.mk.
include/configs/JSE.h defines "CONFIG_4x", not "CONFIG_4xx".
I believe it is a typo because "CONFIG_4x" is not used at all
in other files.
So, I also deleted "CONFIG_4x" in include/configs/JSE.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 14 Jan 2014 01:55:02 +0000 (10:55 +0900)]
board: tec-ng: Do not make directories in a board Makefile
Commit
e5c5301f refactored the build system not to make
directories in board makefiles.
But commit
8f380381 create directories again in
board/avionic-design/tec-ng/Makefile.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Masahiro Yamada [Wed, 8 Jan 2014 11:11:48 +0000 (20:11 +0900)]
drivers: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 8 Jan 2014 11:11:27 +0000 (20:11 +0900)]
include: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 8 Jan 2014 11:11:02 +0000 (20:11 +0900)]
board: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Masahiro Yamada [Wed, 8 Jan 2014 11:10:46 +0000 (20:10 +0900)]
x86: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Wed, 8 Jan 2014 11:10:33 +0000 (20:10 +0900)]
powerpc: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 8 Jan 2014 11:10:15 +0000 (20:10 +0900)]
blackfin: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 8 Jan 2014 11:09:13 +0000 (20:09 +0900)]
avr32: delete unused header files
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 6 Jan 2014 06:45:09 +0000 (15:45 +0900)]
avr32: move CONFIG_AVR32 definition to arch/avr32/config.mk
Like other architectures, CONFIG_AVR32 can be defined
in arch/avr32/config.mk rather than board header files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Masahiro Yamada [Mon, 6 Jan 2014 06:39:48 +0000 (15:39 +0900)]
Remove obsolete _LINUX_CONFIG_H macro
Commit
643aae1406c93ddc64fcf8c136b47cdffd9c8ccd
deleted include/linux/config.h but missed to
delete _LINUX_CONFIG_H macro.
It is no longer used at all.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Tue, 24 Dec 2013 06:30:39 +0000 (15:30 +0900)]
tools: move kermit files to tools/kermit directory
The script files, define2mk.sed and make-asm-offsets
are used to create autoconf.mk and asm-offsets.h
while build.
Whereas README, dot.kermrc, flash_param, send_cmd, send_image
are files useful for kermit.
We should not put files which have the totally different purpose
into the same directory.
This commit creates a new directory, tools/kermit,
and move kermit files into it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>