Wong Vee Khee [Mon, 30 Mar 2020 15:53:57 +0000 (23:53 +0800)]
net: stmmac: Add support for VLAN Rx filtering
Add support for VLAN ID-based filtering by the MAC controller for MAC
drivers that support it. Only the 12-bit VID field is used.
Signed-off-by: Chuah Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Mar 2020 17:33:23 +0000 (10:33 -0700)]
Merge branch 'crypto-chelsio-Fixes-issues-during-chcr-driver-registration'
Ayush Sawal says:
====================
crypto: chelsio: Fixes issues during chcr driver registration
Patch 1: Avoid the accessing of wrong u_ctx pointer.
Patch 2: Fixes a deadlock between rtnl_lock and uld_mutex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayush Sawal [Mon, 30 Mar 2020 15:18:53 +0000 (20:48 +0530)]
Crypto: chelsio - Fixes a deadlock between rtnl_lock and uld_mutex
The locks are taken in this order during driver registration
(uld_mutex), at: cxgb4_register_uld.part.14+0x49/0xd60 [cxgb4]
(rtnl_mutex), at: rtnetlink_rcv_msg+0x2db/0x400
(uld_mutex), at: cxgb_up+0x3a/0x7b0 [cxgb4]
(rtnl_mutex), at: chcr_add_xfrmops+0x83/0xa0 [chcr](stucked here)
To avoid this now the netdev features are updated after the
cxgb4_register_uld function is completed.
Fixes: 6dad4e8ab3ec6 ("chcr: Add support for Inline IPSec").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ayush Sawal [Mon, 30 Mar 2020 15:18:52 +0000 (20:48 +0530)]
Crypto: chelsio - Fixes a hang issue during driver registration
This issue occurs only when multiadapters are present. Hang
happens because assign_chcr_device returns u_ctx pointer of
adapter which is not yet initialized as for this adapter cxgb_up
is not been called yet.
The last_dev pointer is used to determine u_ctx pointer and it
is initialized two times in chcr_uld_add in chcr_dev_add respectively.
The fix here is don't initialize the last_dev pointer during
chcr_uld_add. Only assign to value to it when the adapter's
initialization is completed i.e in chcr_dev_add.
Fixes: fef4912b66d62 ("crypto: chelsio - Handle PCI shutdown event").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthieu Baerts [Mon, 30 Mar 2020 14:23:54 +0000 (16:23 +0200)]
selftests:mptcp: fix failure due to whitespace damage
'pm_nl_ctl' was adding a trailing whitespace after having printed the
IP. But at the end, the IP element is currently always the last one.
The bash script launching 'pm_nl_ctl' had trailing whitespaces in the
expected result on purpose. But these whitespaces have been removed when
the patch has been applied upstream. To avoid trailing whitespaces in
the bash code, 'pm_nl_ctl' and expected results have now been adapted.
The MPTCP PM selftest can now pass again.
Fixes: eedbc685321b (selftests: add PM netlink functional tests)
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 30 Mar 2020 10:16:39 +0000 (11:16 +0100)]
net: ethernet: ti: fix spelling mistake "rundom" -> "random"
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Mar 2020 17:14:36 +0000 (10:14 -0700)]
Merge tag 'mlx5-updates-2020-03-29' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2020-03-29
1) mlx5 core level updates for mkey APIs + migrate some code to mlx5_ib
2) Use a separate work queue for fib event handling
3) Move new eswitch chains files to a new directory, to prepare for
upcoming E-Switch and offloads features.
4) Support indr block setup (TC_SETUP_FT) in Flow Table mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
wenxu [Wed, 25 Mar 2020 12:18:59 +0000 (20:18 +0800)]
net/mlx5e: add mlx5e_rep_indr_setup_ft_cb support
Add mlx5e_rep_indr_setup_ft_cb to support indr block setup
in FT mode.
Both tc rules and flow table rules are of the same format,
It can re-use tc parsing for that, and move the flow table rules
to their steering domain(the specific chain_index), the indr
block offload in FT also follow this scenario.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
wenxu [Wed, 25 Mar 2020 12:18:58 +0000 (20:18 +0800)]
net/mlx5e: refactor indr setup block
Refactor indr setup block for support ft indr setup in the
next patch. The function mlx5e_rep_indr_offload exposes
'flags' in order set additional flag for FT in next patch.
Rename mlx5e_rep_indr_setup_tc_block to mlx5e_rep_indr_setup_block
and add flow_setup_cb_t callback parameters in order set the
specific callback for FT in next patch.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Sat, 14 Mar 2020 01:27:35 +0000 (18:27 -0700)]
net/mlx5: E-Switch: Move eswitch chains to a new directory
eswitch_offloads_chains.{c,h} were just introduced this kernel release
cycle, eswitch is in high development demand right now and many
features are planned to be added to it. eswitch deserves its own
directory and here we move these new files to there, in preparation for
upcoming eswitch features and new files.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Mark Zhang [Tue, 17 Mar 2020 09:28:28 +0000 (11:28 +0200)]
net/mlx5: Use a separate work queue for fib event handling
In VF lag mode when remove the bonding module without bring down the
bond device first, we could potentially have circular dependency when we
unload IB devices and also handle fib events:
1. The bond work starts first;
2. The "modprobe -rv bonding" process tries to release the bond device,
with the "pernet_ops_rwsem" lock hold;
3. The bond work blocks in unregister_netdevice_notifier() and waits for
the lock because fib event came right before;
4. The kernel fib module tries to free all the fib entries by broadcasting
the "FIB_EVENT_NH_DEL" event;
5. Upon the fib event this lag_mp module holds the fib lock and queue a
fib work.
So:
bond work -> modprobe task -> kernel fib module -> lag_mp -> bond work
Today we either reload IB devices in roce lag in nic mode or either handle
fib events in switchdev mode, but a new feature could change that we'll
need to reload IB devices also in switchdev mode so this is a future proof
fix as one may not notice this later.
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Saeed Mahameed [Mon, 30 Mar 2020 06:41:50 +0000 (23:41 -0700)]
Merge branch 'mlx5-next' of git://git./linux/kernel/git/mellanox/linux
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
mlx5: Remove uninitialized use of key in mlx5_core_create_mkey
{IB,net}/mlx5: Move asynchronous mkey creation to mlx5_ib
{IB,net}/mlx5: Assign mkey variant in mlx5_ib only
{IB,net}/mlx5: Setup mkey variant before mr create command invocation
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
David S. Miller [Mon, 30 Mar 2020 05:32:37 +0000 (22:32 -0700)]
Merge branch 'ethtool-netlink-interface-part-4'
Michal Kubecek says:
====================
ethtool netlink interface, part 4
Implementation of more netlink request types:
- coalescing (ethtool -c/-C, patches 2-4)
- pause parameters (ethtool -a/-A, patches 5-7)
- EEE settings (--show-eee / --set-eee, patches 8-10)
- timestamping info (-T, patches 11-12)
Patch 1 is a fix for netdev reference leak similar to commit
2f599ec422ad
("ethtool: fix reference leak in some *_SET handlers") but fixing a code
Changes in v3
- change "one-step-*" Tx type names to "onestep-*", (patch 11, suggested
by Richard Cochran
- use "TSINFO" rather than "TIMESTAMP" for timestamping information
constants and adjust symbol names (patch 12, suggested by Richard
Cochran)
Changes in v2:
- fix compiler warning in net_hwtstamp_validate() (patch 11)
- fix follow-up lines alignment (whitespace only, patches 3 and 8)
which is only in net-next tree at the moment.
====================
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:58 +0000 (00:01 +0100)]
ethtool: provide timestamping information with TSINFO_GET request
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.
Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.
v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:53 +0000 (00:01 +0100)]
ethtool: add timestamping related string sets
Add three string sets related to timestamping information:
ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
ETH_SS_TS_TX_TYPES: timestamping Tx types
ETH_SS_TS_RX_FILTERS: timestamping Rx filters
These will be used for TIMESTAMP_GET request.
v2: avoid compiler warning ("enumeration value not handled in switch")
in net_hwtstamp_validate()
v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:48 +0000 (00:01 +0100)]
ethtool: add EEE_NTF notification
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:43 +0000 (00:01 +0100)]
ethtool: set EEE settings with EEE_SET request
Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.
The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:38 +0000 (00:01 +0100)]
ethtool: provide EEE settings with EEE_GET request
Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.
The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:33 +0000 (00:01 +0100)]
ethtool: add PAUSE_NTF notification
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:28 +0000 (00:01 +0100)]
ethtool: set pause parameters with PAUSE_SET request
Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:23 +0000 (00:01 +0100)]
ethtool: provide pause parameters with PAUSE_GET request
Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:18 +0000 (00:01 +0100)]
ethtool: add COALESCE_NTF notification
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters
of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink
message or ETHTOOL_SCOALESCE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:13 +0000 (00:01 +0100)]
ethtool: set coalescing parameters with COALESCE_SET request
Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:08 +0000 (00:01 +0100)]
ethtool: provide coalescing parameters with COALESCE_GET request
Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Fri, 27 Mar 2020 23:01:03 +0000 (00:01 +0100)]
ethtool: fix reference leak in ethnl_set_privflags()
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. One of them is
ethnl_set_privflags(), a simple reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool --set-priv-flags veth1 foo on
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
Fixes: f265d799596a ("ethtool: set device private flags with PRIVFLAGS_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Mar 2020 05:30:57 +0000 (22:30 -0700)]
Merge branch 'ipv6-add-rpl-source-routing'
Alexander Aring says:
====================
net: ipv6: add rpl source routing
This patch series will add handling for RPL source routing handling
and insertion (implement as lwtunnel)! I did an example prototype
implementation in rpld for using this implementation in non-storing mode:
https://github.com/linux-wpan/rpld/tree/nonstoring_mode
I will also present a talk at netdev about it:
https://netdevconf.info/0x14/session.html?talk-extend-segment-routing-for-RPL
In receive handling I add handling for IPIP encapsulation as RFC6554
describes it as possible. For reasons I didn't implemented it yet for
generating such packets because I am not really sure how/when this
should happen. So far I understand there exists a draft yet which
describes the cases (inclusive a Hop-by-Hop option which we also not
support yet).
https://tools.ietf.org/html/draft-ietf-roll-useofrplinfo-35
This is just the beginning to start implementation everything for yet,
step by step. It works for my use cases yet to have it running on a
6LOWPAN _only_ network.
I have some patches for iproute2 as well.
A sidenote: I check on local addresses if they are part of segment
routes, this is just to avoid stupid settings. A use can add addresses
afterwards what I cannot control anymore but then it's users fault to
make such thing. The receive handling checks for this as well which is
required by RFC6554, so the next hops or when it comes back should drop
it anyway.
To make this possible I added functionality to pass the net structure to
the build_state of lwtunnel (I hope I caught all lwtunnels).
Another sidenote: I set the headroom value to 0 as I figured out it will
break on interfaces with IPv6 min mtu if set to non zero for tunnels on
L3.
- Alex
changes since v3:
- use parse_nested which isn't deprecated - Thanks David Ahern
- change to return -1 instead errno in exthdr handling to unify
error code
- change function name from ipv6_rpl_srh_decompress_size to
ipv6_rpl_srh_size
changes since v2:
- add additional segdata length in lwtunnel build_state
- fix build_state patch by not catching one inline noop function
if LWTUNNEL is disabled
Alexander Aring (5):
include: uapi: linux: add rpl sr header definition
addrconf: add functionality to check on rpl requirements
net: ipv6: add support for rpl sr exthdr
net: add net available in build_state
net: ipv6: add rpl sr tunnel
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 27 Mar 2020 22:00:22 +0000 (18:00 -0400)]
net: ipv6: add rpl sr tunnel
This patch adds functionality to configure routes for RPL source routing
functionality. There is no IPIP functionality yet implemented which can
be added later when the cases when to use IPv6 encapuslation comes more
clear.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 27 Mar 2020 22:00:21 +0000 (18:00 -0400)]
net: add net available in build_state
The build_state callback of lwtunnel doesn't contain the net namespace
structure yet. This patch will add it so we can check on specific
address configuration at creation time of rpl source routes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 27 Mar 2020 22:00:20 +0000 (18:00 -0400)]
net: ipv6: add support for rpl sr exthdr
This patch adds rpl source routing receive handling. Everything works
only if sysconf "rpl_seg_enabled" and source routing is enabled. Mostly
the same behaviour as IPv6 segmentation routing. To handle compression
and uncompression a rpl.c file is created which contains the necessary
functionality. The receive handling will also care about IPv6
encapsulated so far it's specified as possible nexthdr in RFC 6554.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 27 Mar 2020 22:00:19 +0000 (18:00 -0400)]
addrconf: add functionality to check on rpl requirements
This patch adds a functionality to addrconf to check on a specific RPL
address configuration. According to RFC 6554:
To detect loops in the SRH, a router MUST determine if the SRH
includes multiple addresses assigned to any interface on that
router. If such addresses appear more than once and are separated by
at least one address not assigned to that router.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring [Fri, 27 Mar 2020 22:00:18 +0000 (18:00 -0400)]
include: uapi: linux: add rpl sr header definition
This patch adds a uapi header for rpl struct definition. The segments
data can be accessed over rpl_segaddr or rpl_segdata macros. In case of
compri and compre is zero the segment data is not compressed and can be
accessed by rpl_segaddr. In the other case the compressed data can be
accessed by rpl_segdata and interpreted as byte array.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Mar 2020 05:14:49 +0000 (22:14 -0700)]
Merge branch 'mptcp-multiple-subflows-path-management'
Mat Martineau says:
====================
Multipath TCP part 3: Multiple subflows and path management
v2 -> v3: Remove 'inline' in .c files, fix uapi bit macros, and rebase.
v1 -> v2: Rebase on current net-next, fix for netlink limit setting,
and update .gitignore for selftest.
This patch set allows more than one TCP subflow to be established and
used for a multipath TCP connection. Subflows are added to an existing
connection using the MP_JOIN option during the 3-way handshake. With
multiple TCP subflows available, sent data is now stored in the MPTCP
socket so it may be retransmitted on any TCP subflow if there is no
DATA_ACK before a timeout. If an MPTCP-level timeout occurs, data is
retransmitted using an available subflow. Storing this sent data
requires the addition of memory accounting at the MPTCP level, which was
previously delegated to the single subflow. Incoming DATA_ACKs now free
data from the MPTCP-level retransmit buffer.
IP addresses available for new subflow connections can now be advertised
and received with the ADD_ADDR option, and the corresponding REMOVE_ADDR
option likewise advertises that an address is no longer available.
The MPTCP path manager netlink interface has commands to set in-kernel
limits for the number of concurrent subflows and control the
advertisement of IP addresses between peers.
To track and debug MPTCP connections there are new MPTCP MIB counters,
and subflow context can be requested using inet_diag. The MPTCP
self-tests now validate multiple-subflow operation and the netlink path
manager interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:53 +0000 (14:48 -0700)]
selftests: add test-cases for MPTCP MP_JOIN
Use the pm netlink to configure the creation of several
subflows, and verify that via MIB counters.
Update the mptcp_connect program to allow reliable MP_JOIN
handshake even on small data file
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:52 +0000 (14:48 -0700)]
selftests: add PM netlink functional tests
This introduces basic self-tests for the PM netlink,
checking the basic APIs and possible exceptional
values.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:51 +0000 (14:48 -0700)]
mptcp: add netlink-based PM
Expose a new netlink family to userspace to control the PM, setting:
- list of local addresses to be signalled.
- list of local addresses used to created subflows.
- maximum number of add_addr option to react
When the msk is fully established, the PM netlink attempts to
announce the 'signal' list via the ADD_ADDR option. Since we
currently lack the ADD_ADDR echo (and related event) only the
first addr is sent.
After exhausting the 'announce' list, the PM tries to create
subflow for each addr in 'local' list, waiting for each
connection to be completed before attempting the next one.
Idea is to add an additional PM hook for ADD_ADDR echo, to allow
the PM netlink announcing multiple addresses, in sequence.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Fri, 27 Mar 2020 21:48:50 +0000 (14:48 -0700)]
mptcp: add and use MIB counter infrastructure
Exported via same /proc file as the Linux TCP MIB counters, so "netstat -s"
or "nstat" will show them automatically.
The MPTCP MIB counters are allocated in a distinct pcpu area in order to
avoid bloating/wasting TCP pcpu memory.
Counters are allocated once the first MPTCP socket is created in a
network namespace and free'd on exit.
If no sockets have been allocated, all-zero mptcp counters are shown.
The MIB counter list is taken from the multipath-tcp.org kernel, but
only a few counters have been picked up so far. The counter list can
be increased at any time later on.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Fri, 27 Mar 2020 21:48:49 +0000 (14:48 -0700)]
mptcp: allow dumping subflow context to userspace
add ulp-specific diagnostic functions, so that subflow information can be
dumped to userspace programs like 'ss'.
v2 -> v3:
- uapi: use bit macros appropriate for userspace
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:48 +0000 (14:48 -0700)]
mptcp: implement and use MPTCP-level retransmission
On timeout event, schedule a work queue to do the retransmission.
Retransmission code closely resembles the sendmsg() implementation and
re-uses mptcp_sendmsg_frag, providing a dummy msghdr - for flags'
sake - and peeking the relevant dfrag from the rtx head.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:47 +0000 (14:48 -0700)]
mptcp: rework mptcp_sendmsg_frag to accept optional dfrag
This will simplify mptcp-level retransmission implementation
in the next patch. If dfrag is provided by the caller, skip
kernel space memory allocation and use data and metadata
provided by the dfrag itself.
Because a peer could ack data at TCP level but refrain from
sending mptcp-level ACKs, we could grow the mptcp socket
backlog indefinitely.
We should thus block mptcp_sendmsg until the peer has acked some of the
sent data.
In order to be able to do so, increment the mptcp socket wmem_queued
counter on memory allocation and decrement it when releasing the memory
on mptcp-level ack reception.
Because TCP performns sndbuf auto-tuning up to tcp_wmem_max[2], make
this the mptcp sk_sndbuf limit.
In the future we could add experiment with autotuning as TCP does in
tcp_sndbuf_expand().
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Fri, 27 Mar 2020 21:48:46 +0000 (14:48 -0700)]
mptcp: allow partial cleaning of rtx head dfrag
After adding wmem accounting for the mptcp socket we could get
into a situation where the mptcp socket can't transmit more data,
and mptcp_clean_una doesn't reduce wmem even if snd_una has advanced
because it currently will only remove entire dfrags.
Allow advancing the dfrag head sequence and reduce wmem,
even though this isn't correct (as we can't release the page).
Because we will soon block on mptcp sk in case wmem is too large,
call sk_stream_write_space() in case we reduced the backlog so
userspace task blocked in sendmsg or poll will be woken up.
This isn't an issue if the send buffer is large, but it is when
SO_SNDBUF is used to reduce it to a lower value.
Note we can still get a deadlock for low SO_SNDBUF values in
case both sides of the connection write to the socket: both could
be blocked due to wmem being too small -- and current mptcp stack
will only increment mptcp ack_seq on recv.
This doesn't happen with the selftest as it uses poll() and
will always call recv if there is data to read.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:45 +0000 (14:48 -0700)]
mptcp: implement memory accounting for mptcp rtx queue
Charge the data on the rtx queue to the master MPTCP socket, too.
Such memory in uncharged when the data is acked/dequeued.
Also account mptcp sockets inuse via a protocol specific pcpu
counter.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:44 +0000 (14:48 -0700)]
mptcp: introduce MPTCP retransmission timer
The timer will be used to schedule retransmission. It's
frequency is based on the current subflow RTO estimation and
is reset on every una_seq update
The timer is clearer for good by __mptcp_clear_xmit()
Also clean MPTCP rtx queue before each transmission.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:43 +0000 (14:48 -0700)]
mptcp: queue data for mptcp level retransmission
Keep the send page fragment on an MPTCP level retransmission queue.
The queue entries are allocated inside the page frag allocator,
acquiring an additional reference to the page for each list entry.
Also switch to a custom page frag refill function, to ensure that
the current page fragment can always host an MPTCP rtx queue entry.
The MPTCP rtx queue is flushed at disconnect() and close() time
Note that now we need to call __mptcp_init_sock() regardless of mptcp
enable status, as the destructor will try to walk the rtx_queue.
v2 -> v3:
- remove 'inline' in foo.c files (David S. Miller)
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 27 Mar 2020 21:48:42 +0000 (14:48 -0700)]
mptcp: update per unacked sequence on pkt reception
So that we keep per unacked sequence number consistent; since
we update per msk data, use an atomic64 cmpxchg() to protect
against concurrent updates from multiple subflows.
Initialize the snd_una at connect()/accept() time.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Krystad [Fri, 27 Mar 2020 21:48:41 +0000 (14:48 -0700)]
mptcp: Implement path manager interface commands
Fill in more path manager functionality by adding a worker function and
modifying the related stub functions to schedule the worker.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Krystad [Fri, 27 Mar 2020 21:48:40 +0000 (14:48 -0700)]
mptcp: Add handling of outgoing MP_JOIN requests
Subflow creation may be initiated by the path manager when
the primary connection is fully established and a remote
address has been received via ADD_ADDR.
Create an in-kernel sock and use kernel_connect() to
initiate connection.
Passive sockets can't acquire the mptcp socket lock at
subflow creation time, so an additional list protected by
a new spinlock is used to track the MPJ subflows.
Such list is spliced into conn_list tail every time the msk
socket lock is acquired, so that it will not interfere
with data flow on the original connection.
Data flow and connection failover not addressed by this commit.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Krystad [Fri, 27 Mar 2020 21:48:39 +0000 (14:48 -0700)]
mptcp: Add handling of incoming MP_JOIN requests
Process the MP_JOIN option in a SYN packet with the same flow
as MP_CAPABLE but when the third ACK is received add the
subflow to the MPTCP socket subflow list instead of adding it to
the TCP socket accept queue.
The subflow is added at the end of the subflow list so it will not
interfere with the existing subflows operation and no data is
expected to be transmitted on it.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Krystad [Fri, 27 Mar 2020 21:48:38 +0000 (14:48 -0700)]
mptcp: Add path manager interface
Add enough of a path manager interface to allow sending of ADD_ADDR
when an incoming MPTCP connection is created. Capable of sending only
a single IPv4 ADD_ADDR option. The 'pm_data' element of the connection
sock will need to be expanded to handle multiple interfaces and IPv6.
Partial processing of the incoming ADD_ADDR is included so the path
manager notification of that event happens at the proper time, which
involves validating the incoming address information.
This is a skeleton interface definition for events generated by
MPTCP.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peter Krystad [Fri, 27 Mar 2020 21:48:37 +0000 (14:48 -0700)]
mptcp: Add ADD_ADDR handling
Add handling for sending and receiving the ADD_ADDR, ADD_ADDR6,
and RM_ADDR suboptions.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Fri, 27 Mar 2020 21:08:35 +0000 (14:08 -0700)]
mlx4: fix "initializer element not constant" compiler error
A recent commit
e8937681797c ("devlink: prepare to support region
operations") used the region_cr_space_str and region_fw_health_str
variables as initializers for the devlink_region_ops structures.
This can result in compiler errors:
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: error: initializer
element is not constant
.name = region_cr_space_str,
^
drivers/net/ethernet/mellanox//mlx4/crdump.c:45:10: note: (near
initialization for ‘region_cr_space_ops.name’)
drivers/net/ethernet/mellanox//mlx4/crdump.c:50:10: error: initializer
element is not constant
.name = region_fw_health_str,
The variables were made to be "const char * const", indicating that both
the pointer and data were constant. This was enough to resolve this on
recent GCC (gcc (GCC) 9.2.1
20190827 (Red Hat 9.2.1-1) for this author).
Unfortunately this is not enough for older compilers to realize that the
variable can be treated as a constant expression.
Fix this by introducing macros for the string and use those instead of
the variable name in the region ops structures.
Reported-by: tanhuazhong <tanhuazhong@huawei.com>
Fixes: e8937681797c ("devlink: prepare to support region operations")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jacob Keller [Fri, 27 Mar 2020 20:55:36 +0000 (13:55 -0700)]
devlink: don't wrap commands in rST shell blocks
The devlink-region.rst and ice-region.rst documentation files wrapped
some lines within shell code blocks due to being longer than 80 lines.
It was pointed out during review that wrapping these lines shouldn't be
done. Fix these two rST files and remove the line wrapping on these
shell command examples.
Reported-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
René van Dorst [Fri, 27 Mar 2020 14:44:12 +0000 (15:44 +0100)]
net: dsa: mt7530: use resolved link config in mac_link_up()
Convert the mt7530 switch driver to use the finalised link
parameters in mac_link_up() rather than the parameters in mac_config().
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Mar 2020 14:00:16 +0000 (16:00 +0200)]
net: dsa: sja1105: show more ethtool statistics counters for P/Q/R/S
It looks like the P/Q/R/S series supports some more counters,
generically named "Ethernet statistics counter", which we were not
printing. Add them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 27 Mar 2020 11:00:42 +0000 (12:00 +0100)]
s390/qeth: support net namespaces for L3 devices
Enable the L3 driver's IPv4 address notifier to watch for events on qeth
devices that have been moved into a net namespace. We need to program
those IPs into the HW just as usual, otherwise inbound traffic won't
flow.
Fixes: 6133fb1aa137 ("[NETNS]: Disable inetaddr notifiers in namespaces other than initial.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cambda Zhu [Thu, 26 Mar 2020 07:33:14 +0000 (15:33 +0800)]
net: Fix typo of SKB_SGO_CB_OFFSET
The SKB_SGO_CB_OFFSET should be SKB_GSO_CB_OFFSET which means the
offset of the GSO in skb cb. This patch fixes the typo.
Fixes: 9207f9d45b0a ("net: preserve IP control block during GSO segmentation")
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Basson [Wed, 25 Mar 2020 20:50:43 +0000 (22:50 +0200)]
qed: Fix race condition between scheduling and destroying the slowpath workqueue
Calling queue_delayed_work concurrently with
destroy_workqueue might race to an unexpected outcome -
scheduled task after wq is destroyed or other resources
(like ptt_pool) are freed (yields NULL pointer dereference).
cancel_delayed_work prevents the race by cancelling
the timer triggered for scheduling a new task.
Fixes: 59ccf86fe ("qed: Add driver infrastucture for handling mfw requests")
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Yuval Basson <ybason@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Denis Kirjanov [Wed, 25 Mar 2020 20:35:28 +0000 (23:35 +0300)]
net: page pool: allow to pass zero flags to page_pool_init()
page pool API can be useful for non-DMA cases like
xen-netfront driver so let's allow to pass zero flags to
page pool flags.
v2: check DMA direction only if PP_FLAG_DMA_MAP is set
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Yang [Wed, 25 Mar 2020 20:32:07 +0000 (13:32 -0700)]
selftests: move timestamping selftests to net folder
For historical reasons, there are several timestamping selftest targets
in selftests/networking/timestamping. Move them to the standard
directory for networking tests: selftests/net.
Signed-off-by: Jian Yang <jianyang@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Schenker [Wed, 25 Mar 2020 17:34:25 +0000 (18:34 +0100)]
ARM: dts: apalis-imx6qdl: use rgmii-id instead of rgmii
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Schenker [Wed, 25 Mar 2020 17:34:24 +0000 (18:34 +0100)]
net: phy: micrel.c: add rgmii interface delay possibility to ksz9131
The KSZ9131 provides DLL controlled delays on RXC and TXC lines. This
patch makes use of those delays. The information which delays should
be enabled or disabled comes from the interface names, documented in
ethernet-controller.yaml:
rgmii: Disable RXC and TXC delays
rgmii-id: Enable RXC and TXC delays
rgmii-txid: Enable only TXC delay, disable RXC delay
rgmii-rxid: Enable onlx RXC delay, disable TXC delay
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark Starovoytov [Wed, 25 Mar 2020 13:01:34 +0000 (16:01 +0300)]
net: macsec: add support for specifying offload upon link creation
This patch adds new netlink attribute to allow a user to (optionally)
specify the desired offload mode immediately upon MACSec link creation.
Separate iproute patch will be required to support this from user space.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 30 Mar 2020 04:25:29 +0000 (21:25 -0700)]
Merge git://git./linux/kernel/git/davem/net
Minor comment conflict in mac80211.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 29 Mar 2020 22:25:41 +0000 (15:25 -0700)]
Linux 5.6
Linus Torvalds [Sun, 29 Mar 2020 17:40:31 +0000 (10:40 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge vm fixes from Andrew Morton:
"5 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm/sparse: fix kernel crash with pfn_section_valid check
mm: fork: fix kernel_stack memcg stats for various stack implementations
hugetlb_cgroup: fix illegal access to memory
drivers/base/memory.c: indicate all memory blocks as removable
mm/swapfile.c: move inode_lock out of claim_swapfile
Linus Torvalds [Sun, 29 Mar 2020 17:36:29 +0000 (10:36 -0700)]
Merge tag 'timers-urgent-2020-03-29' of git://git./linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for the Hyper-V clocksource driver to make sched clock
actually return nanoseconds and not the virtual clock value which
increments at 10e7 HZ (100ns)"
* tag 'timers-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/hyper-v: Make sched clock return nanoseconds correctly
Linus Torvalds [Sun, 29 Mar 2020 17:07:00 +0000 (10:07 -0700)]
Merge tag 'irq-urgent-2020-03-29' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single bugfix to prevent reference leaks in irq affinity notifiers"
* tag 'irq-urgent-2020-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Fix reference leaks on irq affinity notifiers
Aneesh Kumar K.V [Sun, 29 Mar 2020 02:17:29 +0000 (19:17 -0700)]
mm/sparse: fix kernel crash with pfn_section_valid check
Fix the crash like this:
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc000000000c3447c
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
CPU: 11 PID: 7519 Comm: lt-ndctl Not tainted 5.6.0-rc7-autotest #1
...
NIP [
c000000000c3447c] vmemmap_populated+0x98/0xc0
LR [
c000000000088354] vmemmap_free+0x144/0x320
Call Trace:
section_deactivate+0x220/0x240
__remove_pages+0x118/0x170
arch_remove_memory+0x3c/0x150
memunmap_pages+0x1cc/0x2f0
devm_action_release+0x30/0x50
release_nodes+0x2f8/0x3e0
device_release_driver_internal+0x168/0x270
unbind_store+0x130/0x170
drv_attr_store+0x44/0x60
sysfs_kf_write+0x68/0x80
kernfs_fop_write+0x100/0x290
__vfs_write+0x3c/0x70
vfs_write+0xcc/0x240
ksys_write+0x7c/0x140
system_call+0x5c/0x68
The crash is due to NULL dereference at
test_bit(idx, ms->usage->subsection_map);
due to ms->usage = NULL in pfn_section_valid()
With commit
d41e2f3bd546 ("mm/hotplug: fix hot remove failure in
SPARSEMEM|!VMEMMAP case") section_mem_map is set to NULL after
depopulate_section_mem(). This was done so that pfn_page() can work
correctly with kernel config that disables SPARSEMEM_VMEMMAP. With that
config pfn_to_page does
__section_mem_map_addr(__sec) + __pfn;
where
static inline struct page *__section_mem_map_addr(struct mem_section *section)
{
unsigned long map = section->section_mem_map;
map &= SECTION_MAP_MASK;
return (struct page *)map;
}
Now with SPASEMEM_VMEMAP enabled, mem_section->usage->subsection_map is
used to check the pfn validity (pfn_valid()). Since section_deactivate
release mem_section->usage if a section is fully deactivated,
pfn_valid() check after a subsection_deactivate cause a kernel crash.
static inline int pfn_valid(unsigned long pfn)
{
...
return early_section(ms) || pfn_section_valid(ms, pfn);
}
where
static inline int pfn_section_valid(struct mem_section *ms, unsigned long pfn)
{
int idx = subsection_map_index(pfn);
return test_bit(idx, ms->usage->subsection_map);
}
Avoid this by clearing SECTION_HAS_MEM_MAP when mem_section->usage is
freed. For architectures like ppc64 where large pages are used for
vmmemap mapping (16MB), a specific vmemmap mapping can cover multiple
sections. Hence before a vmemmap mapping page can be freed, the kernel
needs to make sure there are no valid sections within that mapping.
Clearing the section valid bit before depopulate_section_memap enables
this.
[aneesh.kumar@linux.ibm.com: add comment]
Link: http://lkml.kernel.org/r/20200326133235.343616-1-aneesh.kumar@linux.ibm.comLink:
Fixes: d41e2f3bd546 ("mm/hotplug: fix hot remove failure in SPARSEMEM|!VMEMMAP case")
Reported-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Reviewed-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Wei Yang <richard.weiyang@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roman Gushchin [Sun, 29 Mar 2020 02:17:25 +0000 (19:17 -0700)]
mm: fork: fix kernel_stack memcg stats for various stack implementations
Depending on CONFIG_VMAP_STACK and the THREAD_SIZE / PAGE_SIZE ratio the
space for task stacks can be allocated using __vmalloc_node_range(),
alloc_pages_node() and kmem_cache_alloc_node().
In the first and the second cases page->mem_cgroup pointer is set, but
in the third it's not: memcg membership of a slab page should be
determined using the memcg_from_slab_page() function, which looks at
page->slab_cache->memcg_params.memcg . In this case, using
mod_memcg_page_state() (as in account_kernel_stack()) is incorrect:
page->mem_cgroup pointer is NULL even for pages charged to a non-root
memory cgroup.
It can lead to kernel_stack per-memcg counters permanently showing 0 on
some architectures (depending on the configuration).
In order to fix it, let's introduce a mod_memcg_obj_state() helper,
which takes a pointer to a kernel object as a first argument, uses
mem_cgroup_from_obj() to get a RCU-protected memcg pointer and calls
mod_memcg_state(). It allows to handle all possible configurations
(CONFIG_VMAP_STACK and various THREAD_SIZE/PAGE_SIZE values) without
spilling any memcg/kmem specifics into fork.c .
Note: This is a special version of the patch created for stable
backports. It contains code from the following two patches:
- mm: memcg/slab: introduce mem_cgroup_from_obj()
- mm: fork: fix kernel_stack memcg stats for various stack implementations
[guro@fb.com: introduce mem_cgroup_from_obj()]
Link: http://lkml.kernel.org/r/20200324004221.GA36662@carbon.dhcp.thefacebook.com
Fixes: 4d96ba353075 ("mm: memcg/slab: stop setting page->mem_cgroup pointer for slab pages")
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Bharata B Rao <bharata@linux.ibm.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200303233550.251375-1-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mina Almasry [Sun, 29 Mar 2020 02:17:22 +0000 (19:17 -0700)]
hugetlb_cgroup: fix illegal access to memory
This appears to be a mistake in commit
faced7e0806cf ("mm: hugetlb
controller for cgroups v2").
Essentially that commit does a hugetlb_cgroup_from_counter assuming that
page_counter_try_charge has initialized counter.
But if that has failed then it seems will not initialize counter, so
hugetlb_cgroup_from_counter(counter) ends up pointing to random memory,
causing kasan to complain.
The solution is to simply use 'h_cg', instead of
hugetlb_cgroup_from_counter(counter), since that is a reference to the
hugetlb_cgroup anyway. After this change kasan ceases to complain.
Fixes: faced7e0806cf ("mm: hugetlb controller for cgroups v2")
Reported-by: syzbot+cac0c4e204952cf449b1@syzkaller.appspotmail.com
Signed-off-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Giuseppe Scrivano <gscrivan@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: David Rientjes <rientjes@google.com>
Link: http://lkml.kernel.org/r/20200313223920.124230-1-almasrymina@google.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Hildenbrand [Sun, 29 Mar 2020 02:17:19 +0000 (19:17 -0700)]
drivers/base/memory.c: indicate all memory blocks as removable
We see multiple issues with the implementation/interface to compute
whether a memory block can be offlined (exposed via
/sys/devices/system/memory/memoryX/removable) and would like to simplify
it (remove the implementation).
1. It runs basically lockless. While this might be good for performance,
we see possible races with memory offlining that will require at
least some sort of locking to fix.
2. Nowadays, more false positives are possible. No arch-specific checks
are performed that validate if memory offlining will not be denied
right away (and such check will require locking). For example, arm64
won't allow to offline any memory block that was added during boot -
which will imply a very high error rate. Other archs have other
constraints.
3. The interface is inherently racy. E.g., if a memory block is detected
to be removable (and was not a false positive at that time), there is
still no guarantee that offlining will actually succeed. So any
caller already has to deal with false positives.
4. It is unclear which performance benefit this interface actually
provides. The introducing commit
5c755e9fd813 ("memory-hotplug: add
sysfs removable attribute for hotplug memory remove") mentioned
"A user-level agent must be able to identify which sections
of memory are likely to be removable before attempting the
potentially expensive operation."
However, no actual performance comparison was included.
Known users:
- lsmem: Will group memory blocks based on the "removable" property. [1]
- chmem: Indirect user. It has a RANGE mode where one can specify
removable ranges identified via lsmem to be offlined. However,
it also has a "SIZE" mode, which allows a sysadmin to skip the
manual "identify removable blocks" step. [2]
- powerpc-utils: Uses the "removable" attribute to skip some memory
blocks right away when trying to find some to offline+remove.
However, with ballooning enabled, it already skips this
information completely (because it once resulted in many false
negatives). Therefore, the implementation can deal with false
positives properly already. [3]
According to Nathan Fontenot, DLPAR on powerpc is nowadays no longer
driven from userspace via the drmgr command (powerpc-utils). Nowadays
it's managed in the kernel - including onlining/offlining of memory
blocks - triggered by drmgr writing to /sys/kernel/dlpar. So the
affected legacy userspace handling is only active on old kernels. Only
very old versions of drmgr on a new kernel (unlikely) might execute
slower - totally acceptable.
With CONFIG_MEMORY_HOTREMOVE, always indicating "removable" should not
break any user space tool. We implement a very bad heuristic now.
Without CONFIG_MEMORY_HOTREMOVE we cannot offline anything, so report
"not removable" as before.
Original discussion can be found in [4] ("[PATCH RFC v1] mm:
is_mem_section_removable() overhaul").
Other users of is_mem_section_removable() will be removed next, so that
we can remove is_mem_section_removable() completely.
[1] http://man7.org/linux/man-pages/man1/lsmem.1.html
[2] http://man7.org/linux/man-pages/man8/chmem.8.html
[3] https://github.com/ibm-power-utilities/powerpc-utils
[4] https://lkml.kernel.org/r/
20200117105759.27905-1-david@redhat.com
Also, this patch probably fixes a crash reported by Steve.
http://lkml.kernel.org/r/CAPcyv4jpdaNvJ67SkjyUJLBnBnXXQv686BiVW042g03FUmWLXw@mail.gmail.com
Reported-by: "Scargall, Steve" <steve.scargall@intel.com>
Suggested-by: Michal Hocko <mhocko@kernel.org>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Nathan Fontenot <ndfont@gmail.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Robert Jennings <rcj@linux.vnet.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200128093542.6908-1-david@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Naohiro Aota [Sun, 29 Mar 2020 02:17:15 +0000 (19:17 -0700)]
mm/swapfile.c: move inode_lock out of claim_swapfile
claim_swapfile() currently keeps the inode locked when it is successful,
or the file is already swapfile (with -EBUSY). And, on the other error
cases, it does not lock the inode.
This inconsistency of the lock state and return value is quite confusing
and actually causing a bad unlock balance as below in the "bad_swap"
section of __do_sys_swapon().
This commit fixes this issue by moving the inode_lock() and IS_SWAPFILE
check out of claim_swapfile(). The inode is unlocked in
"bad_swap_unlock_inode" section, so that the inode is ensured to be
unlocked at "bad_swap". Thus, error handling codes after the locking now
jumps to "bad_swap_unlock_inode" instead of "bad_swap".
=====================================
WARNING: bad unlock balance detected!
5.5.0-rc7+ #176 Not tainted
-------------------------------------
swapon/4294 is trying to release lock (&sb->s_type->i_mutex_key) at: __do_sys_swapon+0x94b/0x3550
but there are no more locks to release!
other info that might help us debug this:
no locks held by swapon/4294.
stack backtrace:
CPU: 5 PID: 4294 Comm: swapon Not tainted 5.5.0-rc7-BTRFS-ZNS+ #176
Hardware name: ASUS All Series/H87-PRO, BIOS 2102 07/29/2014
Call Trace:
dump_stack+0xa1/0xea
print_unlock_imbalance_bug.cold+0x114/0x123
lock_release+0x562/0xed0
up_write+0x2d/0x490
__do_sys_swapon+0x94b/0x3550
__x64_sys_swapon+0x54/0x80
do_syscall_64+0xa4/0x4b0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f15da0a0dc7
Fixes: 1638045c3677 ("mm: set S_SWAPFILE on blockdev swap devices")
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Qais Youef <qais.yousef@arm.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: <stable@vger.kernel.org>
Link: http://lkml.kernel.org/r/20200206090132.154869-1-naohiro.aota@wdc.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 29 Mar 2020 01:55:15 +0000 (18:55 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
1) Fix memory leak in vti6, from Torsten Hilbrich.
2) Fix double free in xfrm_policy_timer, from YueHaibing.
3) NL80211_ATTR_CHANNEL_WIDTH attribute is put with wrong type, from
Johannes Berg.
4) Wrong allocation failure check in qlcnic driver, from Xu Wang.
5) Get ks8851-ml IO operations right, for real this time, from Marek
Vasut.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (22 commits)
r8169: fix PHY driver check on platforms w/o module softdeps
net: ks8851-ml: Fix IO operations, again
mlxsw: spectrum_mr: Fix list iteration in error path
qlcnic: Fix bad kzalloc null test
mac80211: set IEEE80211_TX_CTRL_PORT_CTRL_PROTO for nl80211 TX
mac80211: mark station unauthorized before key removal
mac80211: Check port authorization in the ieee80211_tx_dequeue() case
cfg80211: Do not warn on same channel at the end of CSA
mac80211: drop data frames without key on encrypted links
ieee80211: fix HE SPR size calculation
nl80211: fix NL80211_ATTR_CHANNEL_WIDTH attribute type
xfrm: policy: Fix doulbe free in xfrm_policy_timer
bpf: Explicitly memset some bpf info structures declared on the stack
bpf: Explicitly memset the bpf_attr structure
bpf: Sanitize the bpf_struct_ops tcp-cc name
vti6: Fix memory leak of skb if input policy check fails
esp: remove the skb from the chain when it's enqueued in cryptd_wq
ipv6: xfrm6_tunnel.c: Use built-in RCU list checking
xfrm: add the missing verify_sec_ctx_len check in xfrm_add_acquire
xfrm: fix uctx len check in verify_sec_ctx_len
...
Linus Torvalds [Sat, 28 Mar 2020 20:11:26 +0000 (13:11 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Three more driver bugfixes, and two doc improvements fixing build
warnings while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: pca-platform: Use platform_irq_get_optional
i2c: st: fix missing struct parameter description
i2c: nvidia-gpu: Handle timeout correctly in gpu_i2c_check_status()
i2c: fix a doc warning
i2c: hix5hd2: add missed clk_disable_unprepare in remove
Linus Torvalds [Sat, 28 Mar 2020 16:14:16 +0000 (09:14 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two small fixes: one in drivers (qla2xxx), and one in the core (sd) to
try to cope with USB enclosures that silently change reported
parameters"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix optimal I/O size for devices that change reported values
scsi: qla2xxx: Fix I/Os being passed down when FC device is being deleted
Chris Packham [Thu, 26 Mar 2020 22:44:22 +0000 (11:44 +1300)]
i2c: pca-platform: Use platform_irq_get_optional
The interrupt is not required so use platform_irq_get_optional() to
avoid error messages like
i2c-pca-platform
22080000.i2c: IRQ index 0 not found
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Alain Volmat [Thu, 26 Mar 2020 21:22:43 +0000 (22:22 +0100)]
i2c: st: fix missing struct parameter description
Fix a missing struct parameter description to allow
warning free W=1 compilation.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
David S. Miller [Fri, 27 Mar 2020 23:18:51 +0000 (16:18 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2020-03-27
The following pull-request contains BPF updates for your *net* tree.
We've added 3 non-merge commits during the last 4 day(s) which contain
a total of 4 files changed, 25 insertions(+), 20 deletions(-).
The main changes are:
1) Explicitly memset the bpf_attr structure on bpf() syscall to avoid
having to rely on compiler to do so. Issues have been noticed on
some compilers with padding and other oddities where the request was
then unexpectedly rejected, from Greg Kroah-Hartman.
2) Sanitize the bpf_struct_ops TCP congestion control name in order to
avoid problematic characters such as whitespaces, from Martin KaFai Lau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Mar 2020 23:07:25 +0000 (16:07 -0700)]
Merge branch 'DSA-mtu'
Vladimir Oltean says:
====================
Configure the MTU on DSA switches
This series adds support for configuring the MTU on front-panel switch
ports, while seamlessly adapting the CPU port and the DSA master to the
largest value plus the tagger overhead.
It also implements bridge MTU auto-normalization within the DSA core, as
resulted after the feedback of the implementation of this feature inside
the bridge driver in v2.
Support was added for quite a number of switches, in the hope that this
series would gain some traction:
- sja1105
- felix
- vsc73xx
- b53 and rest of the platform
V3 of this series was submitted here:
https://patchwork.ozlabs.org/cover/
1262394/
V2 of this series was submitted here:
https://patchwork.ozlabs.org/cover/
1261471/
V1 of this series was submitted here:
https://patchwork.ozlabs.org/cover/
1199868/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Mar 2020 19:55:47 +0000 (21:55 +0200)]
net: dsa: felix: support changing the MTU
Changing the MTU for this switch means altering the
DEV_GMII:MAC_CFG_STATUS:MAC_MAXLEN_CFG field MAX_LEN, which in turn
limits the size of frames that can be received.
Special accounting needs to be done for the DSA CPU port (NPI port in
hardware terms). The NPI port configuration needs to be held inside the
private ocelot structure, since it is now accessed from multiple places.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Mar 2020 19:55:46 +0000 (21:55 +0200)]
net: dsa: vsc73xx: make the MTU configurable
Instead of hardcoding the MTU to the maximum value allowed by the
hardware, obey the value known by the operating system.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Mar 2020 19:55:45 +0000 (21:55 +0200)]
net: dsa: sja1105: implement the port MTU callbacks
On this switch, the frame length enforcements are performed by the
ingress policers. There are 2 types of those: regular L2 (also called
best-effort) and Virtual Link policers (an ARINC664/AFDX concept for
defining L2 streams with certain QoS abilities). To avoid future
confusion, I prefer to call the reset reason "Best-effort policers",
even though the VL policers are not yet supported.
We also need to change the setup of the initial static config, such that
DSA calls to .change_mtu (which are expensive) become no-ops and don't
reset the switch 5 times.
A driver-level decision is to unconditionally allow single VLAN-tagged
traffic on all ports. The CPU port must accept an additional VLAN header
for the DSA tag, which is again a driver-level decision.
The policers actually count bytes not only from the SDU, but also from
the Ethernet header and FCS, so those need to be accounted for as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Krishna Policharla [Fri, 27 Mar 2020 19:55:44 +0000 (21:55 +0200)]
net: dsa: b53: add MTU configuration support
It looks like the Broadcom switches supported by the b53 driver don't
support precise configuration of the MTU, but just a mumbo-jumbo boolean
flag. Set that.
Also configure BCM583XX devices to send and receive jumbo frames when
ports are configured with 10/100 Mbps speed.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Mar 2020 19:55:43 +0000 (21:55 +0200)]
net: dsa: implement auto-normalization of MTU for bridge hardware datapath
Many switches don't have an explicit knob for configuring the MTU
(maximum transmission unit per interface). Instead, they do the
length-based packet admission checks on the ingress interface, for
reasons that are easy to understand (why would you accept a packet in
the queuing subsystem if you know you're going to drop it anyway).
So it is actually the MRU that these switches permit configuring.
In Linux there only exists the IFLA_MTU netlink attribute and the
associated dev_set_mtu function. The comments like to play blind and say
that it's changing the "maximum transfer unit", which is to say that
there isn't any directionality in the meaning of the MTU word. So that
is the interpretation that this patch is giving to things: MTU == MRU.
When 2 interfaces having different MTUs are bridged, the bridge driver
MTU auto-adjustment logic kicks in: what br_mtu_auto_adjust() does is it
adjusts the MTU of the bridge net device itself (and not that of the
slave net devices) to the minimum value of all slave interfaces, in
order for forwarded packets to not exceed the MTU regardless of the
interface they are received and send on.
The idea behind this behavior, and why the slave MTUs are not adjusted,
is that normal termination from Linux over the L2 forwarding domain
should happen over the bridge net device, which _is_ properly limited by
the minimum MTU. And termination over individual slave devices is
possible even if those are bridged. But that is not "forwarding", so
there's no reason to do normalization there, since only a single
interface sees that packet.
The problem with those switches that can only control the MRU is with
the offloaded data path, where a packet received on an interface with
MRU 9000 would still be forwarded to an interface with MRU 1500. And the
br_mtu_auto_adjust() function does not really help, since the MTU
configured on the bridge net device is ignored.
In order to enforce the de-facto MTU == MRU rule for these switches, we
need to do MTU normalization, which means: in order for no packet larger
than the MTU configured on this port to be sent, then we need to limit
the MRU on all ports that this packet could possibly come from. AKA
since we are configuring the MRU via MTU, it means that all ports within
a bridge forwarding domain should have the same MTU.
And that is exactly what this patch is trying to do.
>From an implementation perspective, we try to follow the intent of the
user, otherwise there is a risk that we might livelock them (they try to
change the MTU on an already-bridged interface, but we just keep
changing it back in an attempt to keep the MTU normalized). So the MTU
that the bridge is normalized to is either:
- The most recently changed one:
ip link set dev swp0 master br0
ip link set dev swp1 master br0
ip link set dev swp0 mtu 1400
This sequence will make swp1 inherit MTU 1400 from swp0.
- The one of the most recently added interface to the bridge:
ip link set dev swp0 master br0
ip link set dev swp1 mtu 1400
ip link set dev swp1 master br0
The above sequence will make swp0 inherit MTU 1400 as well.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Fri, 27 Mar 2020 19:55:42 +0000 (21:55 +0200)]
net: dsa: configure the MTU for switch ports
It is useful be able to configure port policers on a switch to accept
frames of various sizes:
- Increase the MTU for better throughput from the default of 1500 if it
is known that there is no 10/100 Mbps device in the network.
- Decrease the MTU to limit the latency of high-priority frames under
congestion, or work around various network segments that add extra
headers to packets which can't be fragmented.
For DSA slave ports, this is mostly a pass-through callback, called
through the regular ndo ops and at probe time (to ensure consistency
across all supported switches).
The CPU port is called with an MTU equal to the largest configured MTU
of the slave ports. The assumption is that the user might want to
sustain a bidirectional conversation with a partner over any switch
port.
The DSA master is configured the same as the CPU port, plus the tagger
overhead. Since the MTU is by definition L2 payload (sans Ethernet
header), it is up to each individual driver to figure out if it needs to
do anything special for its frame tags on the CPU port (it shouldn't
except in special cases). So the MTU does not contain the tagger
overhead on the CPU port.
However the MTU of the DSA master, minus the tagger overhead, is used as
a proxy for the MTU of the CPU port, which does not have a net device.
This is to avoid uselessly calling the .change_mtu function on the CPU
port when nothing should change.
So it is safe to assume that the DSA master and the CPU port MTUs are
apart by exactly the tagger's overhead in bytes.
Some changes were made around dsa_master_set_mtu(), function which was
now removed, for 2 reasons:
- dev_set_mtu() already calls dev_validate_mtu(), so it's redundant to
do the same thing in DSA
- __dev_set_mtu() returns 0 if ops->ndo_change_mtu is an absent method
That is to say, there's no need for this function in DSA, we can safely
call dev_set_mtu() directly, take the rtnl lock when necessary, and just
propagate whatever errors get reported (since the user probably wants to
be informed).
Some inspiration (mainly in the MTU DSA notifier) was taken from a
vaguely similar patch from Murali and Florian, who are credited as
co-developers down below.
Co-developed-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Co-developed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Krishna Policharla [Fri, 27 Mar 2020 19:55:41 +0000 (21:55 +0200)]
bgmac: configure MTU and add support for frames beyond 8192 byte size
Change DMA descriptor length to handle jumbo frames beyond 8192 bytes.
Also update jumbo frame max size to include FCS, the DMA packet length
received includes FCS.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Krishna Policharla [Fri, 27 Mar 2020 19:55:40 +0000 (21:55 +0200)]
net: phy: bcm7xx: add jumbo frame configuration to PHY
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Fri, 27 Mar 2020 16:33:32 +0000 (17:33 +0100)]
r8169: fix PHY driver check on platforms w/o module softdeps
On Android/x86 the module loading infrastructure can't deal with
softdeps. Therefore the check for presence of the Realtek PHY driver
module fails. mdiobus_register() will try to load the PHY driver
module, therefore move the check to after this call and explicitly
check that a dedicated PHY driver is bound to the PHY device.
Fixes: f32593773549 ("r8169: check that Realtek PHY driver module is loaded")
Reported-by: Chih-Wei Huang <cwhuang@android-x86.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Mar 2020 22:40:24 +0000 (15:40 -0700)]
Merge tag 'wireless-drivers-next-2020-03-27' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Mar 2020 22:36:57 +0000 (15:36 -0700)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2020-03-27
please apply the following patch series for qeth to netdev's net-next
tree.
Spring clean edition:
- remove one sysfs attribute that was never put in use,
- make support for OSN and OSX devices optional, and
- probe for removal of the obsolete OSN support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 27 Mar 2020 10:19:34 +0000 (11:19 +0100)]
s390/qeth: phase out OSN support
OSN devices currently spend an awful long time in qeth_l2_set_online()
until various unsupported HW cmds time out. This has been broken for
over two years, ever since
commit
d22ffb5a712f ("s390/qeth: fix IPA command submission race")
triggered a FW bug in cmd processing.
Prior to commit
782e4a792147 ("s390/qeth: don't poll for cmd IO completion"),
this wait for timeout would have even been spent busy-polling.
The offending patch was picked up by stable and all relevant distros,
and yet noone noticed.
OSN setups only ever worked in combination with an out-of-tree blob, and
the last machine that even offered HW with OSN support was released back
in 2015.
Rather than attempting to work-around this FW issue for no actual gain,
add a deprecation warning so anyone who still wants to maintain this
part of the code can speak up. Else rip it all out in 2021.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 27 Mar 2020 10:19:33 +0000 (11:19 +0100)]
s390/qeth: make OSN / OSX support configurable
The last machine generation that supports OSN is z13, and OSX is only
supported up to z14. Allow users and distros to decide whether they
still need support for these device types.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 27 Mar 2020 10:19:32 +0000 (11:19 +0100)]
s390/qeth: remove fake_broadcast attribute
Ever since commit
4a71df50047f ("qeth: new qeth device driver") introduced
this attribute, it can be read & written but has no actual effect.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Mar 2020 22:34:43 +0000 (15:34 -0700)]
Merge branch 'bnxt_en-Updates-to-devlink-info_get-cb'
Vasundhara Volam says:
====================
bnxt_en: Updates to devlink info_get cb
This series adds support for a generic macro to devlink info_get cb.
Adds support for fw.mgmt.api and board.id info to bnxt_en driver info_get
cb. Also, updates the devlink-info.rst and bnxt.rst documentation
accordingly.
This series adds a patch to fix few macro names that maps to bnxt_en
firmware versions.
v1->v2: Remove ECN dev param, base_mh_addr and serial number info support
in this series.
Rename drv.spec macro to fw.api.
---
v2->v3: Remove hw.addr info as it is per netdev but not per device info.
---
v3->v4: Rename "fw.api" to "fw.mgmt.api".
Also, add a patch that modifies few macro names in info_get command,
to match the devlink documentation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 27 Mar 2020 09:35:51 +0000 (15:05 +0530)]
bnxt_en: Fix "fw.mgmt" and "fw.nsci" info via devlink info_get cb
Fix macro names to report fw.mgmt and fw.ncsi versions to match the
devlink documentation.
Example display after fixes:
$ devlink dev info pci/0000:af:00.0
pci/0000:af:00.0:
driver bnxt_en
serial_number B0-26-28-FF-FE-25-84-20
versions:
fixed:
board.id BCM957454A4540
asic.id C454
asic.rev 1
running:
fw 216.1.154.0
fw.psid 0.0.0
fw.mgmt 216.1.146.0
fw.mgmt.api 1.10.1
fw.ncsi 864.0.44.0
fw.roce 216.1.16.0
Fixes: 9599e036b161 ("bnxt_en: Add support for devlink info command")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 27 Mar 2020 09:35:50 +0000 (15:05 +0530)]
bnxt_en: Add partno to devlink info_get cb
Add part number info from the vital product data to info_get command
via devlink tool. Update bnxt.rst documentation as well.
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 27 Mar 2020 09:35:49 +0000 (15:05 +0530)]
bnxt_en: Read partno and serialno of the board from VPD
Store the part number and serial number information from VPD in
the bnxt structure. Follow up patch will add the support to display
the information via devlink command.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 27 Mar 2020 09:35:32 +0000 (15:05 +0530)]
PCI: Add new PCI_VPD_RO_KEYWORD_SERIALNO macro
This patch adds a new macro for serial number keyword.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 27 Mar 2020 09:34:52 +0000 (15:04 +0530)]
bnxt_en: Add fw.mgmt.api version to devlink info_get cb.
Display the minimum version of firmware interface spec supported
between driver and firmware. Also update bnxt.rst documentation file.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vasundhara Volam [Fri, 27 Mar 2020 09:34:51 +0000 (15:04 +0530)]
devlink: Add macro for "fw.mgmt.api" to info_get cb.
Add definition and documentation for the new generic info
"fw.mgmt.api". This macro specifies the version of the software
interfaces between driver and firmware.
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 27 Mar 2020 22:06:50 +0000 (15:06 -0700)]
Merge branch 'mlxsw-Various-static-checkers-fixes'
Ido Schimmel says:
====================
mlxsw: Various static checkers fixes
Jakub told me he gets some warnings with W=1, so I decided to check with
sparse, smatch and coccinelle as well. This patch set fixes all the
issues found. None are actual bugs / regressions and therefore not
targeted at net.
Patches #1-#2 add missing kernel-doc comments.
Patch #3 removes dead code.
Patch #4 reworks the ACL code to avoid defining a static variable in a
header file.
Patch #5 removes unnecessary conversion to bool that coccinelle warns
about.
Patch #6 avoids false-positive uninitialized symbol errors emitted by
smatch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>