Rabin Vincent [Mon, 29 Feb 2016 15:22:32 +0000 (16:22 +0100)]
dwc_eth_qos: use GFP_KERNEL in dma_alloc_coherent()
Since we are in non-atomic context here we can pass GFP_KERNEL to
dma_alloc_coherent(). This enables use of the CMA.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lars Persson [Mon, 29 Feb 2016 15:22:31 +0000 (16:22 +0100)]
dwc_eth_qos: release descriptors outside netif_tx_lock
To prepare for using the CMA, we can not be in atomic context when
de-allocating DMA buffers.
The tx lock was needed only to protect the hw reset against the xmit
handler. Now we briefly grab the tx lock while stopping the queue to
make sure no thread is inside or will enter the xmit handler.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rabin Vincent [Mon, 29 Feb 2016 15:22:30 +0000 (16:22 +0100)]
dwc_eth_qos: fix race condition in dwceqos_start_xmit
The xmit handler and the tx_reclaim tasklet had a race on the tx_free
variable which could lead to a tx timeout if tx_free was updated after
the tx complete interrupt.
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:42:46 +0000 (14:42 -0500)]
Merge branch 'mlx4-fixes'
Or Gerlitz says:
====================
Mellanox 10/40G mlx4 driver fixes for 4.5-rc6
This series contains two fixes for the SRIOV HW LAG that was
introduced in 4.5-rc1 and one fix that allows to revoke the
administrative MAC that was assigned to VF through the PF.
The VF mac fix needs to go for stable too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Wed, 2 Mar 2016 15:47:46 +0000 (17:47 +0200)]
net/mlx4_core: Allow resetting VF admin mac to zero
The VF administrative mac addresses (stored in the PF driver) are
initialized to zero when the PF driver starts up.
These addresses may be modified in the PF driver through ndo calls
initiated by iproute2 or libvirt.
While we allow the PF/host to change the VF admin mac address from zero
to a valid unicast mac, we do not allow restoring the VF admin mac to
zero. We currently only allow changing this mac to a different unicast mac.
This leads to problems when libvirt scripts are used to deal with
VF mac addresses, and libvirt attempts to revoke the mac so this
host will not use it anymore.
Fix this by allowing resetting a VF administrative MAC back to zero.
Fixes:
8f7ba3ca12f6 ('net/mlx4: Add set VF mac address support')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Moshe Levi <moshele@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moni Shoua [Wed, 2 Mar 2016 15:47:45 +0000 (17:47 +0200)]
net/mlx4_core: Check the correct limitation on VFs for HA mode
The limit of 63 is only for virtual functions while the actual enforcement
was for VFs plus physical functions, fix that.
Fixes:
e57968a10bc1 ('net/mlx4_core: Support the HA mode for SRIOV VFs too')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jack Morgenstein [Wed, 2 Mar 2016 15:47:44 +0000 (17:47 +0200)]
net/mlx4_core: Fix lockdep warning in handling of mac/vlan tables
In the mac and vlan register/unregister/replace functions, the driver locks
the mac table mutex (or vlan table mutex) on both ports.
We move to use mutex_lock_nested() to prevent warnings, such as the one below.
[ 101.828445] =============================================
[ 101.834820] [ INFO: possible recursive locking detected ]
[ 101.841199] 4.5.0-rc2+ #49 Not tainted
[ 101.850251] ---------------------------------------------
[ 101.856621] modprobe/3054 is trying to acquire lock:
[ 101.862514] (&table->mutex#2){+.+.+.}, at: [<
ffffffffa079c10e>] __mlx4_register_mac+0x87e/0xa90 [mlx4_core]
[ 101.874598]
[ 101.874598] but task is already holding lock:
[ 101.881703] (&table->mutex#2){+.+.+.}, at: [<
ffffffffa079c0f0>] __mlx4_register_mac+0x860/0xa90 [mlx4_core]
[ 101.893776]
[ 101.893776] other info that might help us debug this:
[ 101.901658] Possible unsafe locking scenario:
[ 101.901658]
[ 101.908859] CPU0
[ 101.911923] ----
[ 101.914985] lock(&table->mutex#2);
[ 101.919595] lock(&table->mutex#2);
[ 101.924199]
[ 101.924199] * DEADLOCK *
[ 101.924199]
[ 101.931643] May be due to missing lock nesting notation
Fixes:
5f61385d2ebc ('net/mlx4_core: Keep VLAN/MAC tables mirrored in multifunc HA mode')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Suggested-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 19:37:27 +0000 (14:37 -0500)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
Mellanox 100G mlx5 driver fixes
This series has few bug fixes for the mlx5 Ethernet driver.
Eran fixed a locking issue with time-stamping that could cause a
soft-lockup when time-stamping is enabled.
Gal fixed the rx/tx packets/bytes counters returned by the driver to
actually went through the network stack.
Tariq removed a poll CQ optimization which could lead the driver to
stop getting interrupts for some of the rings, and a did also fix to
HW LRO which is currently broken.
He also provided RSS and RX hash fixes for the case of changing the
number of rx rings the RX hash/RSS configuration will be out of sync.
The time stamping fix from Eran is not for -stable as the feature was
only introduced in 4.5 but all of the others are.
Changes fro V0:
- Eran addressed the irqsave/restore comments from "Dave" and fixed them.
This series is generated against net commit
4c0b6eaf373a 'net:
thunderx: Fix for Qset error due to CQ full'
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Mon, 29 Feb 2016 19:17:15 +0000 (21:17 +0200)]
net/mlx5e: Provide correct packet/bytes statistics
Using the HW VPort counters for traffic (rx/tx packets/bytes)
statistics is wrong. This is because frames dropped due to steering or
out of buffer will be counted as received. To fix that, we move to use
the packet/bytes accounting done by the driver for what the netdev
reports out.
Fixes:
f62b8bb8f2d3 ('net/mlx5: Extend mlx5_core to support [...]')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Mon, 29 Feb 2016 19:17:14 +0000 (21:17 +0200)]
net/mlx5e: Add rx/tx bytes software counters
Sum up rx/tx bytes in software as we do for rx/tx packets, to be reported
in upcoming statistics fix.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 29 Feb 2016 19:17:13 +0000 (21:17 +0200)]
net/mlx5e: Correctly handle RSS indirection table when changing number of channels
Upon changing num_channels, reset the RSS indirection table to
match the new value.
Fixes:
2d75b2bc8a8c ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 29 Feb 2016 19:17:12 +0000 (21:17 +0200)]
net/mlx5e: Fix ethtool RX hash func configuration change
We should modify TIRs explicitly to apply the new RSS configuration.
The light ndo close/open calls do not "refresh" them.
Fixes:
2d75b2bc8a8c ('net/mlx5e: Add ethtool RSS configuration options')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha [Mon, 29 Feb 2016 19:17:11 +0000 (21:17 +0200)]
net/mlx5e: Fix soft lockup when HW Timestamping is enabled
Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.
The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
Interrupt routine calls napi_schedule(), which triggers rx/tx
skb process.
An attempt to read SW timecounter using read_lock is done, which is
already locked by a writer on the same CPU and cause soft lockup.
Add irqsave/irqrestore for when using the readers/writers lock for
writing.
Fixes:
ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 29 Feb 2016 19:17:10 +0000 (21:17 +0200)]
net/mlx5e: Fix LRO modify
Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.
Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.
Fixes:
5c50368f3831 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 29 Feb 2016 19:17:09 +0000 (21:17 +0200)]
net/mlx5e: Remove wrong poll CQ optimization
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.
We revert this optimization.
Fixes:
e586b3b0baee ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunhao Lin [Wed, 2 Mar 2016 16:59:15 +0000 (00:59 +0800)]
r8169: Enable RX_MULTI_EN for RTL_GIGA_MAC_VER_41~48
For RTL8168G/RTL8168H/RTL8411B/RTL8107E, enable this flag to eliminate
message "AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x0002
address=0x0000000000003000 flags=0x0050] in dmesg.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 18:35:31 +0000 (13:35 -0500)]
Merge tag 'mac80211-for-davem-2016-03-02' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are a few more fixes for the current cycle:
* check GCMP encryption vs. fragmentation properly; we'd found
this problem quite a while ago but waited for the 802.11 spec
to be updated
* fix RTS/CTS logic in minstrel_ht
* fix RX of certain public action frames in AP mode
* add mac80211_hwsim to MAC80211 in MAINTAINERS, this helps
the kbuild robot pick up the right tree for it
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 2 Mar 2016 18:31:58 +0000 (13:31 -0500)]
Merge branch 'bnx2x-fixes'
Michal Schmidt says:
====================
bnx2x: endianness fixes
this fixes a VLAN crash and some SRIOV bugs in bnx2x observed on ppc64.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:11 +0000 (13:47 +0100)]
bnx2x: fix indentation in bnx2x_sp_task()
Fix a case of misleading code indentation.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:10 +0000 (13:47 +0100)]
bnx2x: define event data reserved fields as little-endian
For consistency with other event data structs and to lessen
the chance of a mistake should one of the reserved fields become
used in the future, define the reserved fields as little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:09 +0000 (13:47 +0100)]
bnx2x: define fields of struct cfc_del_event_data as little-endian
There were no missing endianness conversions in this case, but the
fields of struct cfc_del_event_data should be defined as little-endian
to get rid of the ugly (__force __le32) casts.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:08 +0000 (13:47 +0100)]
bnx2x: access cfc_del_event only if the opcode is CFC_DEL
It's not really a bug, but it was odd that bnx2x_eq_int() read the
message data as if it were a cfc_del_event regardless of the event type.
It's cleaner to access only the appropriate member of union event_data
after checking the event opcode.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:07 +0000 (13:47 +0100)]
bnx2x: fix receive of VF->PF mailbox messages by the PF on big-endian
On ppc64 the PF did not receive messages from VFs correctly.
Fields of struct vf_pf_event_data are little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:06 +0000 (13:47 +0100)]
bnx2x: fix sending VF->PF messages on big-endian
When a VF is sending a message to the PF, it needs to trigger the PF
to tell it the message is ready.
The trigger did not work on ppc64. No interrupt appeared in the PF.
The bug is due to confusion about the layout of struct trigger_vf_zone.
In bnx2x_send_msg2pf() the trigger is written using writeb(), not
writel(), so the attempt to define the struct with a reversed layout on
big-endian is counter-productive.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Schmidt [Wed, 2 Mar 2016 12:47:05 +0000 (13:47 +0100)]
bnx2x: fix crash on big-endian when adding VLAN
bnx2x crashes during the initialization of the 8021q module on ppc64.
The bug is a missing conversion from le32 in
bnx2x_handle_classification_eqe() when obtaining the cid value from
struct eth_event_data.
The fields in struct eth_event_data should all be declared as
little-endian and conversions added where missing.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Fri, 26 Feb 2016 09:50:34 +0000 (10:50 +0100)]
mac80211_hwsim: treat as part of mac80211 for MAINTAINERS
Since I maintain this driver as part of mac80211, add it to
the file list for mac80211; this helps submitters send it to
me instead of Kalle and also makes the build robot apply the
patches for it on the right tree for build attempts.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sergei Shtylyov [Sun, 28 Feb 2016 19:50:59 +0000 (22:50 +0300)]
of_mdio: fix kernel-doc for of_phy_connect()
The 'flags' parameter of the of_phy_connect() function wasn't described
in the kernel-doc comment...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 28 Feb 2016 02:33:11 +0000 (10:33 +0800)]
sctp: sctp_remaddr_seq_show use the wrong variable to dump transport info
Now in sctp_remaddr_seq_show(), we use variable *tsp to get the param *v.
but *tsp is also used to traversal transport_addr_list, which will cover
the previous value, and make sctp_transport_put work on the wrong transport.
So fix it by adding a new variable to get the param *v.
Fixes:
fba4c330c5b9 ("sctp: hold transport before we access t->asoc in sctp proc")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 28 Feb 2016 02:03:51 +0000 (10:03 +0800)]
sctp: lack the check for ports in sctp_v6_cmp_addr
As the member .cmp_addr of sctp_af_inet6, sctp_v6_cmp_addr should also check
the port of addresses, just like sctp_v4_cmp_addr, cause it's invoked by
sctp_cmp_addr_exact().
Now sctp_v6_cmp_addr just check the port when two addresses have different
family, and lack the port check for two ipv6 addresses. that will make
sctp_hash_cmp() cannot work well.
so fix it by adding ports comparison in sctp_v6_cmp_addr().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Mar 2016 21:52:09 +0000 (16:52 -0500)]
Merge branch 'phy-micrel-fixes'
Alexandre Belloni says:
====================
phy: micrel: fix issues with interrupt on atmel boards
Since the phy is not polled anymore, there were issues getting a link on the
sama5d* xplained boards.
I'm not too sure about were those fixes should go and I'm wondering whether the
first one shoud be made generic.
For the second one, I found the PHY_HAS_MAGICANEG flag that is not used and I
wondering whether this is related to that kind of issue. I had a quick look at
the history and could'nt find its use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre Belloni [Fri, 26 Feb 2016 18:18:23 +0000 (19:18 +0100)]
phy: micrel: Disable auto negotiation on startup
Disable auto negotiation on init to properly detect an already plugged
cable at boot.
At boot, when the phy is started, it is in the PHY_UP state.
However, if a cable is plugged at boot, because auto negociation is already
enabled at the time we get the first interrupt, the phy is already running.
But the state machine then switches from PHY_UP to PHY_AN and calls
phy_start_aneg(). phy_start_aneg() will not do anything because aneg is
already enabled on the phy. It will then wait for a interrupt before going
further. This interrupt will never happen unless the cable is unplugged and
then replugged.
It was working properly before
321beec5047a (net: phy: Use interrupts when
available in NOLINK state) because switching to NOLINK meant starting
polling the phy, even if IRQ were enabled.
Fixes:
321beec5047a (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandre Belloni [Fri, 26 Feb 2016 18:18:22 +0000 (19:18 +0100)]
phy: micrel: Ensure interrupts are reenabled on resume
At least on ksz8081, when getting back from power down, interrupts are
disabled. ensure they are reenabled if they were previously enabled.
This fixes resuming which is failing on the xplained boards from atmel
since
321beec5047a (net: phy: Use interrupts when available in NOLINK
state)
Fixes:
321beec5047a (net: phy: Use interrupts when available in NOLINK state)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault [Fri, 26 Feb 2016 17:45:34 +0000 (18:45 +0100)]
ppp: lock ppp->flags in ppp_read() and ppp_poll()
ppp_read() and ppp_poll() can be called concurrently with ppp_ioctl().
In this case, ppp_ioctl() might call ppp_ccp_closed(), which may update
ppp->flags while ppp_read() or ppp_poll() is reading it.
The update done by ppp_ccp_closed() isn't atomic due to the bit mask
operation ('ppp->flags &= ~(SC_CCP_OPEN | SC_CCP_UP)'), so concurrent
readers might get transient values.
Reading incorrect ppp->flags may disturb the 'ppp->flags & SC_LOOP_TRAFFIC'
test in ppp_read() and ppp_poll(), which in turn can lead to improper
decision on whether the PPP unit file is ready for reading or not.
Since ppp_ccp_closed() is protected by the Rx and Tx locks (with
ppp_lock()), taking the Rx lock is enough for ppp_read() and ppp_poll()
to guarantee that ppp_ccp_closed() won't update ppp->flags
concurrently.
The same reasoning applies to ppp->n_channels. The 'n_channels' field
can also be written to concurrently by ppp_ioctl() (through
ppp_connect_channel() or ppp_disconnect_channel()). These writes aren't
atomic (simple increment/decrement), but are protected by both the Rx
and Tx locks (like in the ppp->flags case). So holding the Rx lock
before reading ppp->n_channels also prevents concurrent writes.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Fri, 26 Feb 2016 08:15:50 +0000 (09:15 +0100)]
bna: fix list corruption
Use list_move_tail() to move MAC address entry from list of pending
to list of active entries. Simple list_add_tail() leaves the entry
also in the first list, this leads to list corruption.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 1 Mar 2016 20:10:38 +0000 (15:10 -0500)]
Merge tag 'linux-can-fixes-for-4.5-
20160226' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-02-26
this is a pull request of one patch for net.
The patch by Maximilain Schneider fixes a kfree() problem during disconnect in
the gs_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Wed, 24 Feb 2016 11:07:17 +0000 (12:07 +0100)]
mac80211: minstrel_ht: fix a logic error in RTS/CTS handling
RTS/CTS needs to be enabled if the rate is a fallback rate *or* if it's
a dual-stream rate and the sta is in dynamic SMPS mode.
Cc: stable@vger.kernel.org
Fixes:
a3ebb4e1b763 ("mac80211: minstrel_ht: handle peers in dynamic SMPS")
Reported-by: Matías Richart <mrichart@fing.edu.uy>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jouni Malinen [Mon, 29 Feb 2016 22:29:00 +0000 (00:29 +0200)]
mac80211: Fix Public Action frame RX in AP mode
Public Action frames use special rules for how the BSSID field (Address
3) is set. A wildcard BSSID is used in cases where the transmitter and
recipient are not members of the same BSS. As such, we need to accept
Public Action frames with wildcard BSSID.
Commit
db8e17324553 ("mac80211: ignore frames between TDLS peers when
operating as AP") added a rule that drops Action frames to TDLS-peers
based on an Action frame having different DA (Address 1) and BSSID
(Address 3) values. This is not correct since it misses the possibility
of BSSID being a wildcard BSSID in which case the Address 1 would not
necessarily match.
Fix this by allowing mac80211 to accept wildcard BSSID in an Action
frame when in AP mode.
Fixes:
db8e17324553 ("mac80211: ignore frames between TDLS peers when operating as AP")
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg [Fri, 26 Feb 2016 21:13:40 +0000 (22:13 +0100)]
mac80211: check PN correctly for GCMP-encrypted fragmented MPDUs
Just like for CCMP we need to check that for GCMP the fragments
have PNs that increment by one; the spec was updated to fix this
security issue and now has the following text:
The receiver shall discard MSDUs and MMPDUs whose constituent
MPDU PN values are not incrementing in steps of 1.
Adapt the code for CCMP to work for GCMP as well, luckily the
relevant fields already alias each other so no code duplication
is needed (just check the aliasing with BUILD_BUG_ON.)
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Neil Horman [Thu, 25 Feb 2016 18:02:50 +0000 (13:02 -0500)]
3c59x: mask LAST_FRAG bit from length field in ring
Recently, I fixed a bug in 3c59x:
commit
6e144419e4da11a9a4977c8d899d7247d94ca338
Author: Neil Horman <nhorman@tuxdriver.com>
Date: Wed Jan 13 12:43:54 2016 -0500
3c59x: fix another page map/single unmap imbalance
Which correctly rebalanced dma mapping and unmapping types. Unfortunately it
introduced a new bug which causes oopses on older systems.
When mapping dma regions, the last entry for a packet in the 3c59x tx ring
encodes a LAST_FRAG bit, which is encoded as the high order bit of the buffers
length field. When it is unmapped the LAST_FRAG bit is cleared prior to being
passed to the unmap function. Unfortunately the commit above fails to do that
masking. It was missed in testing because the system on which I tested it had
an intel iommu, the driver for which ignores the size field, using only the DMA
address as the token to identify the mapping to be released. However, on older
systems that rely on swiotlb (or other dma drivers that key off that length
field), not masking off that LAST_FRAG high order bit results in parsing a huge
size to be release, leading to all sorts of odd corruptions and the like.
Fix is easy, just mask the length with 0xFFF. It should really be
&(LAST_FRAG-1), but 0xFFF is the style of the file, and I'd like to make this
fix minimal and correct before making it prettier.
Appies to the net tree cleanly. All testing on both iommu and swiommu based
systems produce good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MINOURA Makoto / 箕浦 真 [Thu, 25 Feb 2016 05:20:48 +0000 (14:20 +0900)]
net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump.
When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maximilain Schneider [Tue, 23 Feb 2016 01:17:28 +0000 (01:17 +0000)]
can: gs_usb: fixed disconnect bug by removing erroneous use of kfree()
gs_destroy_candev() erroneously calls kfree() on a struct gs_can *, which is
allocated through alloc_candev() and should instead be freed using
free_candev() alone.
The inappropriate use of kfree() causes the kernel to hang when
gs_destroy_candev() is called.
Only the struct gs_usb * which is allocated through kzalloc() should be freed
using kfree() when the device is disconnected.
Signed-off-by: Maximilian Schneider <max@schneidersoft.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sunil Goutham [Wed, 24 Feb 2016 11:10:50 +0000 (16:40 +0530)]
net: thunderx: Fix for Qset error due to CQ full
On Thunderx pass 1.x and pass2 due to a HW errata default CQ
DROP_LEVEL of 0x80 is not sufficient to avoid CQ_WR_FULL Qset
error when packets are being received at >20Mpps resulting in
complete stall of packet reception.
This patch will configure it to 0x100 which is what is expected
by HW on Thunderx. On future passes of thunderx and other chips
HW default/reset value will be 0x100 or higher hence not overwritten.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chun-Hao Lin [Wed, 24 Feb 2016 06:18:42 +0000 (14:18 +0800)]
r8169:fix "rtl_counters_cond == 1 (loop: 1000, delay: 10)" log spam.
There will be a log spam when there is no cable plugged. Please refer to
following links. https://bugzilla.kernel.org/show_bug.cgi?id=104351
https://bugzilla.kernel.org/show_bug.cgi?id=107421
This issue is caused by runtime power management. When there is no cable
plugged, the driver will be suspend (runtime suspend) by OS and NIC will be
put into the D3 state. During this time, if OS call rtl8169_get_stats64()
to dump tally counter, because NIC is in D3 state, the register value read
by driver will return all 0xff. This will let driver think tally counter
flag is not toggled and then sends the warning message "rtl_counters_cond
== 1 (loop: 1000, delay: 10)" to kernel log.
For fixing this issue, 1.add checking driver's pm runtime status in
rtl8169_get_stats64(). 2.dump tally counter before going runtime suspend
for counter accuracy in runtime suspend.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Lüssing [Wed, 24 Feb 2016 03:21:42 +0000 (04:21 +0100)]
net: fix bridge multicast packet checksum validation
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<
800204e0>] (unwind_backtrace) from [<
8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<
8001cf14>] (show_stack) from [<
801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<
801ab614>] (dump_stack) from [<
802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<
802e4548>] (__skb_checksum_complete) from [<
803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<
803a055c>] (ipv6_mc_validate_checksum) from [<
802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<
802e111c>] (skb_checksum_trimmed) from [<
803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<
803a06e8>] (ipv6_mc_check_mld) from [<
803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<
803b2c98>] (br_multicast_rcv) from [<
803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes:
9afd85c9e455 ("net: Export IGMP/MLD message validation code")
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 23 Feb 2016 19:23:24 +0000 (19:23 +0000)]
net: qca_spi: clear IFF_TX_SKB_SHARING
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by
qca_spi as it modifies the skb on xmit.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes:
291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Wahren [Tue, 23 Feb 2016 19:23:23 +0000 (19:23 +0000)]
net: qca_spi: Don't clear IFF_BROADCAST
Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes:
291ab06ecf67 (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern [Tue, 23 Feb 2016 18:10:26 +0000 (10:10 -0800)]
net: vrf: Remove direct access to skb->data
Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.
Fixes:
35402e313663 ("net: Add IPv6 support to VRF device")
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Diego Viola [Tue, 23 Feb 2016 15:04:04 +0000 (12:04 -0300)]
net: jme: fix suspend/resume on JMC260
The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.
Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.
Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 24 Feb 2016 21:58:12 +0000 (16:58 -0500)]
Merge tag 'mac80211-for-davem-2016-02-23' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Another small set of fixes:
* stop critical protocol session on disconnect to avoid
it getting stuck
* wext: fix two RTNL message ordering issues
* fix an uninitialized value (found by KASAN)
* fix an out-of-bounds access (also found by KASAN)
* clear connection keys when freeing them in all cases
(IBSS, all other places already did so)
* fix expected throughput unit to get consistent values
* set default TX aggregation timeout to 0 in minstrel
to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Tue, 23 Feb 2016 01:05:26 +0000 (02:05 +0100)]
bpf: fix csum setting for bpf_set_tunnel_key
The fix in
35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.
Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.
Fixes:
35e2d1152b22 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.")
Fixes:
c6c33454072f ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hannes Frederic Sowa [Mon, 22 Feb 2016 17:43:25 +0000 (18:43 +0100)]
ipv4: only create late gso-skb if skb is already set up with CHECKSUM_PARTIAL
Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL
skbs down. This can easily happen with UDP+IPv4 sockets with the first
MSG_MORE write smaller than the MTU, second write is a sendfile.
Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path,
were we calculate the checksum manually during copying.
Commit
d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked
sockets") started to exposes this bug.
Fixes:
d749c9cbffd6 ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets")
Reported-by: Jiri Benc <jbenc@redhat.com>
Cc: Jiri Benc <jbenc@redhat.com>
Reported-by: Wakko Warner <wakko@animx.eu.org>
Cc: Wakko Warner <wakko@animx.eu.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sebastian Frias [Mon, 22 Feb 2016 12:33:14 +0000 (13:33 +0100)]
net: ethernet: nb8800: support fixed-link DT node
Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.
https://stackoverflow.com/questions/
31046172/device-tree-for-phy-less-connection-to-a-dsa-switch
This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Acked-by: Mans Rullgard <mans@mansr.com>
Cc: Mason <slash.tmp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 22 Feb 2016 07:10:26 +0000 (02:10 -0500)]
bnxt_en: Fix zero padding of tx push data.
The arithmetic to zero pad the last 64-bit word in the push buffer is not
correct.
1. It should be pdata + length to get to the end.
2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the
aligned pointer to void. Pass 'end' which is u64 pointer to PTR_ALIGN()
instead so that the aligned pointer - 1 is the last 64-bit pointer to data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bernie Harris [Sun, 21 Feb 2016 23:58:05 +0000 (12:58 +1300)]
tunnel: Clear IPCB(skb)->opt before dst_link_failure called
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in
11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Konstantin Khlebnikov [Sun, 21 Feb 2016 07:12:39 +0000 (10:12 +0300)]
tcp: convert cached rtt from usec to jiffies when feeding initial rto
Currently it's converted into msecs, thus HZ=1000 intact.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes:
740b0f1841f6 ("tcp: switch rtt estimations to usec resolution")
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrik Halfar [Sat, 20 Feb 2016 17:49:40 +0000 (18:49 +0100)]
Add Dell Wireless 5809e Gobi 4G HSPA+ Mobile Broadband Card (rev3) to qmi_wwan
New revison of Dell Wireless 5809e Gobi 4G HSPA+ Mobile Broadband Card has new idProduct
Bus 002 Device 006: ID 413c:81b3 Dell Computer Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x413c Dell Computer Corp.
idProduct 0x81b3
bcdDevice 0.06
iManufacturer 1 Sierra Wireless, Incorporated
iProduct 2 Dell Wireless 5809e Gobi™ 4G HSPA+ Mobile Broadband Card
iSerial 3
bNumConfigurations 2
Signed-off-by: Patrik Halfar <patrik_halfar@halfarit.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arend van Spriel [Mon, 15 Feb 2016 13:35:53 +0000 (14:35 +0100)]
cfg80211: stop critical protocol session upon disconnect event
When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ola Olsson [Thu, 11 Feb 2016 00:00:22 +0000 (01:00 +0100)]
nl80211: Zero out the connection keys memory when freeing them.
The connection keys are zeroed out in all other cases except this
one. Let's fix the last one as well.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Felix Fietkau [Thu, 18 Feb 2016 18:49:18 +0000 (19:49 +0100)]
mac80211: minstrel_ht: set default tx aggregation timeout to 0
The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.
Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.
Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linus Torvalds [Mon, 22 Feb 2016 20:18:07 +0000 (12:18 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
Linus Torvalds [Mon, 22 Feb 2016 20:12:46 +0000 (12:12 -0800)]
Merge tag 'hwmon-for-linus-v4.5-rc6' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two fixes headed for stable:
- Remove an unnecessary speed_index lookup for thermal hook in the
gpio-fan driver. The unnecessary speed lookup can hog the system.
- Handle negative conversion values correctly in the ads1015 driver"
* tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
hwmon: (ads1015) Handle negative conversion values correctly
Linus Torvalds [Mon, 22 Feb 2016 20:04:11 +0000 (12:04 -0800)]
Merge tag 'for-linus' of git://git./linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"One ocrdma fix:
- The new CQ API support was added to ocrdma, but they got the arming
logic wrong, so without this, transfers eventually fail when they
fail to arm the interrupt properly under load
Two related fixes for mlx4:
- When we added the 64bit extended counters support to the core IB
code, they forgot to update the RoCE side of the mlx4 driver (the
IB side they properly updated).
I debated whether or not to include these patches as they could be
considered feature enablement patches, but the existing code will
blindy copy the 32bit counters, whether any counters were requested
at all (a bug).
These two patches make it (a) check to see that counters were
requested and (b) copy the right counters (the 64bit support is
new, the 32bit is not). For that reason I went ahead and took
them"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx4: Add support for the port info class for RoCE ports
IB/mlx4: Add support for extended counters over RoCE ports
RDMA/ocrdma: Fix arm logic to align with new cq API
Linus Torvalds [Mon, 22 Feb 2016 19:55:18 +0000 (11:55 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some bugfixes from I2C for you:
A fix for a RuntimePM regression with OMAP, a fix to enable TCO for
Lewisburg platforms, and a typo fix while we are here"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Adding Intel Lewisburg support for iTCO
i2c: uniphier: fix typos in error messages
i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit
David S. Miller [Mon, 22 Feb 2016 03:51:55 +0000 (22:51 -0500)]
Merge tag 'linux-can-fixes-for-4.5-
20160221' of git://git./linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-02-21
this is a pull reqeust of one patch for net/master.
The patch is by Gerhard Uttenthaler and fixes a potential tx overflow in the
ems_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Feb 2016 03:50:55 +0000 (22:50 -0500)]
Merge branch 'bnx2x-848xx-phy-fixes'
Yuval Mintz says:
====================
bnx2x: Fix 848xx phys
This series contains link-related fixes, mostly for the 848xx phys
[2 patches are for 84833, and 2 patches are for 84858].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 21 Feb 2016 13:07:29 +0000 (15:07 +0200)]
bnx2x: Fix 84833 phy command handler
Current initialization sequence is lacking, causing some configurations
to fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 21 Feb 2016 13:07:28 +0000 (15:07 +0200)]
bnx2x: Fix led setting for 84858 phy.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 21 Feb 2016 13:07:27 +0000 (15:07 +0200)]
bnx2x: Correct 84858 PHY fw version
The phy's firmware version isn't being parsed properly as it's
currently parsed like the rest of the 848xx phys.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 21 Feb 2016 13:07:26 +0000 (15:07 +0200)]
bnx2x: Fix 84833 RX CRC
There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz [Sun, 21 Feb 2016 13:07:25 +0000 (15:07 +0200)]
bnx2x: Fix link-forcing for KR2
Currently, when link is using KR2 it cannot be forced to any speed other
than 20g.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.om>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Feb 2016 03:46:26 +0000 (22:46 -0500)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2016-02-20
Here's an important patch for 4.5 which fixes potential invalid pointer
access when processing completed Bluetooth HCI commands.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Robert Jarzmik [Sat, 20 Feb 2016 20:45:26 +0000 (21:45 +0100)]
net: ethernet: davicom: fix devicetree irq resource
The dm9000 driver doesn't work in at least one device-tree
configuration, spitting an error message on irq resource :
[ 1.062495] dm9000 8000000.ethernet: insufficient resources
[ 1.068439] dm9000 8000000.ethernet: not found (-2).
[ 1.073451] dm9000: probe of 8000000.ethernet failed with error -2
The reason behind is that the interrupt might be provided by a gpio
controller, not probed when dm9000 is probed, and needing the probe
deferral mechanism to apply.
Currently, the interrupt is directly taken from resources. This patch
changes this to use the more generic platform_get_irq(), which handles
the deferral.
Moreover, since commit Fixes:
7085a7401ba5 ("drivers: platform: parse
IRQ flags from resources"), the interrupt trigger flags are honored in
platform_get_irq(), so remove the needless code in dm9000.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Sergei Ianovich <ynvich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Sat, 20 Feb 2016 10:14:36 +0000 (19:14 +0900)]
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
fix incorrect indexing of dev->dev_addr[] when copying the MAC address
of FMV-J182 at buf[5].
Signed-off-by: Ken Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shrikrishna Khare [Fri, 19 Feb 2016 19:19:52 +0000 (11:19 -0800)]
Driver: Vmxnet3: Update Rx ring 2 max size
Device emulation supports max size of 4096.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 22 Feb 2016 03:03:21 +0000 (22:03 -0500)]
Merge branch 'netcp-fixes'
Murali Karicheri says:
====================
net: ti: netcp: restore get/set_pad_info() functionality
This series fixes a regression and add some improvements for the ease
of maintainance. Incorporated comments against v1.
Changelogs:
v2 : combined 2-3 into one patch as this involves a header change
fixed a parse warning in 3/4 per comment from Arnd.
Removed Sign-off from Arnd against 1/4
added comments in 3/3 to alert on the usage of sw data per review
comments
v1 : added 2-4 to accomodate feedback received from review
v0 : initial version to fix the regression (From Grygorii)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Karicheri, Muralidharan [Fri, 19 Feb 2016 17:58:44 +0000 (12:58 -0500)]
net: netcp: rework the code for get/set sw_data in dma desc
SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karicheri, Muralidharan [Fri, 19 Feb 2016 17:58:43 +0000 (12:58 -0500)]
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.
Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.
Rename the helpers to match with the updated dma desc field sw_data.
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karicheri, Muralidharan [Fri, 19 Feb 2016 17:58:42 +0000 (12:58 -0500)]
net: ti: netcp: restore get/set_pad_info() functionality
The commit
899077791403 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.
The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.
Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].
Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Arnd Bergmann <arnd@arndb.de>
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Campbell [Fri, 19 Feb 2016 11:44:51 +0000 (11:44 +0000)]
MAINTAINERS: Drop myself as xen netback maintainer
Wei has been picking this up for quite a while now.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Thu, 18 Feb 2016 21:10:57 +0000 (16:10 -0500)]
sctp: Fix port hash table size computation
Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires. The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table). Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).
To fix this, we change the logic slightly. We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support. Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made. Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.
I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Dmitry Vyukov <dvyukov@google.com>
CC: Vladislav Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gerhard Uttenthaler [Tue, 22 Dec 2015 16:29:16 +0000 (17:29 +0100)]
can: ems_usb: Fix possible tx overflow
This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Linus Torvalds [Sat, 20 Feb 2016 21:39:35 +0000 (13:39 -0800)]
Linux 4.5-rc5
Linus Torvalds [Sat, 20 Feb 2016 17:32:40 +0000 (09:32 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This is unusually large, partly due to the EFI fixes that prevent
accidental deletion of EFI variables through efivarfs that may brick
machines. These fixes are somewhat involved to maintain compatibility
with existing install methods and other usage modes, while trying to
turn off the 'rm -rf' bricking vector.
Other fixes are for large page ioremap()s and for non-temporal
user-memcpy()s"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix vmalloc_fault() to handle large pages properly
hpet: Drop stale URLs
x86/uaccess/64: Handle the caching of 4-byte nocache copies properly in __copy_user_nocache()
x86/uaccess/64: Make the __copy_user_nocache() assembly code more readable
lib/ucs2_string: Correct ucs2 -> utf8 conversion
efi: Add pstore variables to the deletion whitelist
efi: Make efivarfs entries immutable by default
efi: Make our variable validation list include the guid
efi: Do variable name validation tests in utf8
efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version
lib/ucs2_string: Add ucs2 -> utf8 helper functions
Linus Torvalds [Sat, 20 Feb 2016 17:30:42 +0000 (09:30 -0800)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"A handful of CPU hotplug related fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Plug potential memory leak in CPU_UP_PREPARE
perf/core: Remove the bogus and dangerous CPU_DOWN_FAILED hotplug state
perf/core: Remove bogus UP_CANCELED hotplug state
perf/x86/amd/uncore: Plug reference leak
Linus Torvalds [Sat, 20 Feb 2016 17:22:11 +0000 (09:22 -0800)]
Merge tag 'powerpc-4.5-3' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix build error on 32-bit with checkpoint restart from Aneesh Kumar
- Fix dedotify for binutils >= 2.26 from Andreas Schwab
- Don't trace hcalls on offline CPUs from Denis Kirjanov
- eeh: Fix stale cached primary bus from Gavin Shan
- eeh: Fix stale PE primary bus from Gavin Shan
- mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V
- ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy
* tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/ioda: Set "read" permission when "write" is set
powerpc/mm: Fix Multi hit ERAT cause by recent THP update
powerpc/powernv: Fix stale PE primary bus
powerpc/eeh: Fix stale cached primary bus
powerpc/pseries: Don't trace hcalls on offline CPUs
powerpc: Fix dedotify for binutils >= 2.26
powerpc/book3s_32: Fix build error with checkpoint restart
Linus Torvalds [Sat, 20 Feb 2016 17:19:56 +0000 (09:19 -0800)]
Merge tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"A few fixes for drivers, nothing major here.
Fixes are: iotdma fix to restart channels, new ID for wildcat PCH,
residue fix for edma, disable irq for non-cyclic in dw"
* tag 'dmaengine-fix-4.5-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: disable BLOCK IRQs for non-cyclic xfer
dmaengine: edma: fix residue race for cyclic
dmaengine: dw: pci: add ID for WildcatPoint PCH
dmaengine: IOATDMA: fix timer code that continues to restart channels during idle
Linus Torvalds [Sat, 20 Feb 2016 17:16:51 +0000 (09:16 -0800)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk driver fixes from Stephen Boyd:
"An assortment of vendor specific clk drivers fixes, most notably
fallout from adding Tegra210 and rockchip rk3036/rk3368 drivers this
cycle.
There's also the random smattering of sparse/checker fixes, a build
"fix" to get the Tango clk driver to compile because the Kconfig
symbol was renamed after the fact, and a clk gpio fix for a patch
mismerge"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (28 commits)
clk: gpio: Really allow an optional clock= DT property
Revert "clk: qcom: Specify LE device endianness"
clk: versatile: mask VCO bits before writing
clk: tegra: super: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warnings for functions not declared as static
clk: tegra: Fix sparse warning for pll_m
clk: tegra: Use definition for pll_u override bit
clk: tegra: Fix warning caused by pll_u failing to lock
clk: tegra: Fix clock sources for Tegra210 EMC
clk: tegra: Add the APB2APE audio clock on Tegra210
clk: tegra: Add missing of_node_put()
clk: tegra: Fix PLLE SS coefficients
clk: tegra: Fix typos around clearing PLLE bits during enable
clk: tegra: Do not disable PLLE when under hardware control
clk: tegra: Fix pllx dyn step calculation
clk: tegra: pll: Fix potential sleeping-while-atomic
clk: tegra: Fix the misnaming of nvenc from msenc
clk: tegra: Fix naming of MISC registers
clk: tango4: rename ARCH_TANGOX to ARCH_TANGO
clk: scpi: Fix checking return value of platform_device_register_simple()
...
Linus Torvalds [Sat, 20 Feb 2016 17:13:18 +0000 (09:13 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm fixes from Dave Airlie:
"Some more fixes trickled in:
A bunch of VC4 ones since it's a pretty new driver not much chance of
regressions, and it fixes GPU resets.
Also one atomic fix, one set of fixes for a common bug in TTM cleanup,
and one i915 hotplug fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/nouveau: use post-decrement in error handling
drm/atomic: Allow for holes in connector state, v2.
drm/i915: Fix hpd live status bits for g4x
drm/vc4: Use runtime PM to power cycle the device when the GPU hangs.
drm/vc4: Enable runtime PM.
drm/vc4: Fix spurious GPU resets due to BO reuse.
drm/vc4: Drop error message on seqno wait timeouts.
drm/vc4: Fix -ERESTARTSYS error return from BO waits.
drm/vc4: Return an ERR_PTR from BO creation instead of NULL.
drm/vc4: Fix the clear color for the first tile rendered.
drm/vc4: Validate that WAIT_BO padding is cleared.
drm/radeon: use post-decrement in error handling
drm/amdgpu: use post-decrement in error handling
Simon Guinot [Wed, 9 Sep 2015 22:15:18 +0000 (00:15 +0200)]
kernel/resource.c: fix muxed resource handling in __request_region()
In __request_region, if a conflict with a BUSY and MUXED resource is
detected, then the caller goes to sleep and waits for the resource to be
released. A pointer on the conflicting resource is kept. At wake-up
this pointer is used as a parent to retry to request the region.
A first problem is that this pointer might well be invalid (if for
example the conflicting resource have already been freed). Another
problem is that the next call to __request_region() fails to detect a
remaining conflict. The previously conflicting resource is passed as a
parameter and __request_region() will look for a conflict among the
children of this resource and not at the resource itself. It is likely
to succeed anyway, even if there is still a conflict.
Instead, the parent of the conflicting resource should be passed to
__request_region().
As a fix, this patch doesn't update the parent resource pointer in the
case we have to wait for a muxed region right after.
Reported-and-tested-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Tested-by: Vincent Donnefort <vdonnefort@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Douglas Anderson [Fri, 19 Feb 2016 22:25:21 +0000 (14:25 -0800)]
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
In commit
44d271377479 ("Bluetooth: Compress the size of struct
hci_ctrl") we squashed down the size of the structure by using a union
with the assumption that all users would use the flag to determine
whether we had a req_complete or a req_complete_skb.
Unfortunately we had a case in hci_req_cmd_complete() where we weren't
looking at the flag. This can result in a situation where we might be
storing a hci_req_complete_skb_t in a hci_req_complete_t variable, or
vice versa.
During some testing I found at least one case where the function
hci_req_sync_complete() was called improperly because the kernel thought
that it didn't require an SKB. Looking through the stack in kgdb I
found that it was called by hci_event_packet() and that
hci_event_packet() had both of its locals "req_complete" and
"req_complete_skb" pointing to the same place: both to
hci_req_sync_complete().
Let's make sure we always check the flag.
For more details on debugging done, see <http://crbug.com/588288>.
Fixes:
44d271377479 ("Bluetooth: Compress the size of struct hci_ctrl")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jaedon Shin [Fri, 19 Feb 2016 04:48:50 +0000 (13:48 +0900)]
net: bcmgenet: Fix internal PHY link state
The PHY link state is not chaged in GENETv2 caused by the previous
commit
49f7a471e4d1 ("net: bcmgenet: Properly configure PHY to ignore
interrupt") was set to PHY_IGNORE_INTERRUPT in bcmgenet_mii_probe().
The internal PHY should use phy_mac_interrupt() when not in use
PHY_POLL. The statement for phy_mac_interrupt() has two conditions. The
first condition to check GENET_HAS_MDIO_INTR is not related PHY link
state, so this patch removes it.
Fixes:
49f7a471e4d1 ("net: bcmgenet: Properly configure PHY to ignore interrupt")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Thu, 18 Feb 2016 12:39:46 +0000 (12:39 +0000)]
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
The unix_stream_read_generic function tries to use a continue statement
to restart the receive loop after waiting for a message. This may not
work as intended as the caller might use a recvmsg call to peek at
control messages without specifying a message buffer. If this was the
case, the continue will cause the function to return without an error
and without the credential information if the function had to wait for a
message while it had returned with the credentials otherwise. Change to
using goto to restart the loop without checking the condition first in
this case so that credentials are returned either way.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry V. Levin [Fri, 19 Feb 2016 01:27:48 +0000 (04:27 +0300)]
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
The value passed by unix_diag_get_exact to unix_lookup_by_ino has type
__u32, but unix_lookup_by_ino's argument ino has type int, which is not
a problem yet.
However, when ino is compared with sock_i_ino return value of type
unsigned long, ino is sign extended to signed long, and this results
to incorrect comparison on 64-bit architectures for inode numbers
greater than INT_MAX.
This bug was found by strace test suite.
Fixes:
5d3cae8bc39d ("unix_diag: Dumping exact socket core")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 20 Feb 2016 04:39:32 +0000 (23:39 -0500)]
Merge branch 'bnxt_en-fixes'
Michael Chan says:
====================
bnxt_en: Phy related fixes.
3 small patches to fix PHY related code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 20 Feb 2016 00:43:21 +0000 (19:43 -0500)]
bnxt_en: Failure to update PHY is not fatal condition.
If we fail to update the PHY, we should print a warning and continue.
The current code to exit is buggy as it has not freed up the NIC
resources yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 20 Feb 2016 00:43:20 +0000 (19:43 -0500)]
bnxt_en: Remove unnecessary call to update PHY settings.
Fix bnxt_update_phy_setting() to check the correct parameters when
determining whether to update the PHY. Requested line speed/duplex should
only be checked for forced speed mode. This avoids unnecessary link
interruptions when loading the driver.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Sat, 20 Feb 2016 00:43:19 +0000 (19:43 -0500)]
bnxt_en: Poll link at the end of __bnxt_open_nic().
When shutting down the NIC, we shutdown async event processing before
freeing all the rings. If there is a link change event during reset, the
driver may miss it and the link state may be incorrect after the NIC is
re-opened. Poll the link at the end of __bnxt_open_nic() to get the
correct link status.
Signed-off-by Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nishanth Menon [Sat, 20 Feb 2016 00:09:51 +0000 (18:09 -0600)]
hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
Thermal hook gpio_fan_get_cur_state is only interested in knowing
the current speed index that was setup in the system, this is
already available as part of fan_data->speed_index which is always
set by set_fan_speed. Using get_fan_speed_index is useful when we
have no idea about the fan speed configuration (for example during
fan_ctrl_init).
When thermal framework invokes
gpio_fan_get_cur_state=>get_fan_speed_index via gpio_fan_get_cur_state
especially in a polled configuration for thermal governor, we
basically hog the i2c interface to the extent that other functions
fail to get any traffic out :(.
Instead, just provide the last state set in the driver - since the gpio
fan driver is responsible for the fan state immaterial of override, the
fan_data->speed_index should accurately reflect the state.
Fixes:
b5cf88e46bad ("(gpio-fan): Add thermal control hooks")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Linus Torvalds [Fri, 19 Feb 2016 21:44:12 +0000 (13:44 -0800)]
Merge tag 'ext4_for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull ext4 bugfixes from Ted Ts'o:
"Miscellaneous ext4 bug fixes for v4.5"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix crashes in dioread_nolock mode
ext4: fix bh->b_state corruption
ext4: fix memleak in ext4_readdir()
ext4: remove unused parameter "newblock" in convert_initialized_extent()
ext4: don't read blocks from disk after extents being swapped
ext4: fix potential integer overflow
ext4: add a line break for proc mb_groups display
ext4: ioctl: fix erroneous return value
ext4: fix scheduling in atomic on group checksum failure
ext4 crypto: move context consistency check to ext4_file_open()
ext4 crypto: revalidate dentry after adding or removing the key
Linus Torvalds [Fri, 19 Feb 2016 21:40:42 +0000 (13:40 -0800)]
Merge branch 'for-linus-4.5' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fix from Chris Mason:
"My for-linus-4.5 branch has a btrfs DIO error passing fix.
I know how much you love DIO, so I'm going to suggest against reading
it. We'll follow up with a patch to drop the error arg from
dio_end_io in the next merge window."
* 'for-linus-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix direct IO requests not reporting IO error to user space