Devin Heitmueller [Thu, 23 Jul 2009 00:56:37 +0000 (21:56 -0300)]
[media] xc4000: remove xc5000 firmware loading routine
Since we use the xc3028 version of the firmware file parsing routine (which
includes support for scodes and separate blobs), we can drop the xc5000
version of the code.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Thu, 23 Jul 2009 00:52:11 +0000 (21:52 -0300)]
[media] xc4000: remove XREG_BUSY code only supported in xc5000
The xc4000 driver is based on the original xc5000 driver, and while the
xc5000 supports the XREG_BUSY register, the xc4000 does not. So remove the
code in question.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Thu, 23 Jul 2009 00:49:28 +0000 (21:49 -0300)]
[media] xc4000: properly set type for init1 firmware
We need to set the firmware type properly in order to locate the init1
firmware.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Mon, 20 Jul 2009 05:15:31 +0000 (02:15 -0300)]
[media] xc4000: cut over to using xc5000 version for loading i2c sequences
The xc3028 version does i2c splitting in a different manner than xc4000 and
xc5000, so reuse the xc5000 version of the routine (the key here being that
xc4000 expects the first *two* bytes to be the same for splitting transactions.
Doing it the xc3028 way was resulting in i2c errors partially through the
firmware load. With this change, it would appear that the entire base firmware
is being loaded successfully (product id now properly shows 0x0FA0).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Mon, 20 Jul 2009 03:54:57 +0000 (00:54 -0300)]
[media] xc4000: pull in firmware management code from xc3028
Switch over to using the firmware management routines from the tuner-xc2028,
since that has support for scodes, etc.
This code still requires signficant cleanup, and at this point the base
firmware does not load properly (i2c write errors about 300 bytes in).
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Mon, 20 Jul 2009 03:45:25 +0000 (00:45 -0300)]
[media] dib7000p: setup dev.parent for i2c master built into 7000p
We need to set the dev.parent member on the dib7000p on its i2c master, or
else calls to request_firmware() will hit an oops in 2.6.31.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Mon, 20 Jul 2009 03:42:33 +0000 (00:42 -0300)]
[media] dib0700: add a sleep before attempting to detect dib7000p
Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Tue, 30 Jun 2009 00:11:02 +0000 (21:11 -0300)]
[media] dib0700: successfully connect to xc4000 over i2c for PCTV 340e
Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Wed, 24 Jun 2009 03:07:01 +0000 (00:07 -0300)]
[media] dib0700: properly setup GPIOs for PCTV 340e
Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.
Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devin Heitmueller [Wed, 24 Jun 2009 01:48:02 +0000 (22:48 -0300)]
[media] dib0700: add USB id for PCTV 340eSE
Add the board profile for the PCTV 340eSE, since that's what I have here
for development.
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Davide Ferri [Wed, 24 Jun 2009 01:34:06 +0000 (22:34 -0300)]
[media] dib0700: add initial code for PCTV 340e by Davide Ferri
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Johannes Obermaier [Thu, 2 Jun 2011 16:03:41 +0000 (13:03 -0300)]
[media] mt9v011: Fixed gain calculation
The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.
The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)
The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.
This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Johannes Obermaier [Thu, 2 Jun 2011 15:43:14 +0000 (12:43 -0300)]
[media] mt9v011: Added exposure for mt9v011
There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.
This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Johannes Obermaier [Thu, 2 Jun 2011 15:17:51 +0000 (12:17 -0300)]
[media] mt9v011: Fixed incorrect value for the first valid column
According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
David Härdeman [Wed, 30 Mar 2011 14:20:14 +0000 (11:20 -0300)]
[media] rc-core: fix winbond-cir issues
The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.
[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Thu, 26 May 2011 08:55:08 +0000 (05:55 -0300)]
[media] rc/redrat3: dereferencing null pointer
In the original code, if the allocation failed we dereference "rr3"
when it was NULL.
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Thu, 26 May 2011 08:52:01 +0000 (05:52 -0300)]
[media] rc: double unlock in rc_register_device()
If change_protocol() fails and we goto out_raw, then it calls unlock
twice. I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Andreas Oberritter [Thu, 26 May 2011 10:54:14 +0000 (07:54 -0300)]
[media] DVB: dvb_frontend: fix dtv_property_dump for DTV_DVBT2_PLP_ID
- Add missing entry to array "dtv_cmds".
- Set array size to DTV_MAX_COMMAND + 1 to avoid future off-by-ones.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Uwe Kleine-König [Wed, 1 Jun 2011 20:19:22 +0000 (17:19 -0300)]
[media] V4L/videobuf2-memops: use pr_debug for debug messages
Otherwise they clutter the dmesg buffer even on a production kernel.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manoel Pinheiro [Sat, 7 May 2011 06:49:13 +0000 (03:49 -0300)]
[media] dvb-usb.h function rc5_scan
The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".
See example below in "drivers/media/dvb/dvb-usb/opera1.c":
send_key = (send_key & 0xffff) | 0x0100;
for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
*state = REMOTE_KEY_PRESSED;
*event = rc_map_opera1_table[i].keycode;
opst->last_key_pressed =
rc_map_opera1_table[i].keycode;
break;
}
opst->last_key_pressed = 0;
}
Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ondrej Zary [Wed, 1 Jun 2011 19:57:11 +0000 (16:57 -0300)]
[media] radio-sf16fmr2: convert to generic TEA575x interface
Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Petter Selasky [Mon, 23 May 2011 11:42:40 +0000 (08:42 -0300)]
[media] cx24113: Don't reuse core macro names
The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Petter Selasky [Mon, 23 May 2011 11:40:00 +0000 (08:40 -0300)]
[media] itd1000: Don't reuse core macro names
The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.
Refactor lineshift in printouts.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Alexey Khoroshilov [Tue, 31 May 2011 20:54:40 +0000 (17:54 -0300)]
[media] radio-si470x: fix memory leak in si470x_usb_driver_probe()
radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Joe Perches [Sat, 28 May 2011 17:36:28 +0000 (14:36 -0300)]
[media] media: Convert vmalloc/memset to vzalloc
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 1 Jun 2011 16:03:12 +0000 (13:03 -0300)]
dvb_net: Simplify the code if DVB NET is not defined
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Petter Selasky [Mon, 23 May 2011 12:43:35 +0000 (09:43 -0300)]
[media] Make DVB NET configurable in the kernel
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ondrej Zary [Mon, 23 May 2011 12:17:19 +0000 (09:17 -0300)]
[media] tea575x: convert to control framework
Convert tea575x-tuner to use the new V4L2 control framework. Also add
ext_init() callback that can be used by a card driver for additional
initialization right before registering the video device (for SF16-FMR2).
Also embed struct video_device to struct snd_tea575x to simplify the code.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hans Petter Selasky [Mon, 23 May 2011 11:13:06 +0000 (08:13 -0300)]
[media] Fix compile warning: Dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sakari Ailus [Sun, 15 May 2011 15:33:58 +0000 (12:33 -0300)]
[media] v4l: Document EACCES in VIDIOC_[GS]_CTRL and VIDIOC_{G, S, TRY}_EXT_CTRLS
VIDIOC_S_CTRL and VIDIOC_S_EXT_CTRLS return EACCES when setting a read-only
control VIDIOC_TRY_EXT_CTRLS when trying a read-only control and
VIDIOC_G_CTRL and VIDIOC_G_EXT_CTRLS when getting a write-only control.
Document this.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newson Edouard [Tue, 19 Apr 2011 14:54:54 +0000 (11:54 -0300)]
[media] videobuf_pages_to_sg: sglist[0] length problem
On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.
Signed-off-by: Newson Edouard <newsondev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tejun Heo [Tue, 15 Feb 2011 09:20:12 +0000 (06:20 -0300)]
[media] cx23885: restore flushes of cx23885_dev work items
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Dan Carpenter [Wed, 24 Nov 2010 05:36:57 +0000 (02:36 -0300)]
[media] saa7164: poll mask set incorrectly
list_first_entry() always returns non-null here. I think the intent was
to test whether there were any entries in the used list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 20:25:53 +0000 (17:25 -0300)]
[media] cxd2820r: correct missing error checks
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 1 Jun 2011 13:23:53 +0000 (10:23 -0300)]
[media] Update several cardlists
Several cardlist entries are missed. Fix them by running some
script magic (about the same scripts we used to have at -hg tree).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 1 Jun 2011 13:16:25 +0000 (10:16 -0300)]
[media] em28xx: use the proper prefix for board names
All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:
EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 20:03:50 +0000 (17:03 -0300)]
[media] em28xx: correct PCTV nanoStick T2 290e device name
PCTV Systems nanoStick T2 290e => PCTV nanoStick T2 290e
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 20:00:35 +0000 (17:00 -0300)]
[media] em28xx: add remote for PCTV nanoStick T2 290e
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 19:56:37 +0000 (16:56 -0300)]
[media] em28xx: EM28174 remote support
For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 15:42:52 +0000 (12:42 -0300)]
[media] cxd2820r: fix bitfields
error: dubious one-bit signed bitfield
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 15:32:44 +0000 (12:32 -0300)]
[media] cxd2820r: malloc buffers instead of stack
kmalloc I2C buffers
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 21:30:09 +0000 (18:30 -0300)]
[media] anysee: style issues, comments, etc
Change some info, comments, variables. No functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Wed, 25 May 2011 21:21:43 +0000 (18:21 -0300)]
[media] anysee: add support for Anysee E7 PS2
Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari [Tue, 24 May 2011 10:57:34 +0000 (07:57 -0300)]
[media] anysee: add support for Anysee E7 PTC
Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jean-François Moine [Mon, 23 May 2011 08:38:10 +0000 (05:38 -0300)]
[media] gspca - ov519: New sensor ov9600 with bridge ovfx2
This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Tue, 31 May 2011 19:27:44 +0000 (16:27 -0300)]
[media] DocBook: Move all media docbook stuff into its own directory
This patch addresses several issues pointed by Randy Dunlap
<rdunlap@xenotime.net> at changeset ece722c:
- In the generated index.html file, "media" is listed first, but it
should be listed in alphabetical order, not first.
- The generated files are (hidden) in .tmpmedia/
- The link from the top-level index.html file to "media" is to
media/index.html, but the file is actually in .tmpmedia/media/index.html
- Please build docs with and without using "O=builddir" and test that.
- Would it be possible for media to have its own Makefile instead of
merging into this one?
Due to the way cleandocs target works, I had to rename the media DocBook
to media_api, otherwise cleandocs would remove the /media directory.
Thanks-to: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mauro Carvalho Chehab [Wed, 25 May 2011 15:24:48 +0000 (12:24 -0300)]
[media] DocBook: Add rules to auto-generate some media docbook
Auto-generate the videodev2.h.xml,frontend.h.xml and the indexes.
Some logic at the Makefile helps us to identify when a symbol is missing,
like for example:
Error: no ID for constraint linkend: V4L2-PIX-FMT-JPGL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Linus Torvalds [Fri, 22 Jul 2011 02:17:23 +0000 (19:17 -0700)]
Linux 3.0
Linus Torvalds [Fri, 22 Jul 2011 00:20:57 +0000 (17:20 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
sparc,kgdbts: fix compile regression with kgdb test suite
Jason Wessel [Tue, 19 Jul 2011 20:43:16 +0000 (15:43 -0500)]
sparc,kgdbts: fix compile regression with kgdb test suite
Commit
63ab25ebbc (kgdbts: unify/generalize gdb breakpoint adjustment)
introduced a compile regression on sparc.
kgdbts.c: In function 'check_and_rewind_pc':
kgdbts.c:307: error: implicit declaration of function 'instruction_pointer_set'
Simply add the correct macro definition for instruction pointer on the
Sparc architecture.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 21 Jul 2011 21:28:01 +0000 (14:28 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
CIFS: Fix wrong length in cifs_iovec_read
Linus Torvalds [Thu, 21 Jul 2011 19:25:39 +0000 (12:25 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Make Dell Latitude E6420 use reboot=pci
x86: Make Dell Latitude E5420 use reboot=pci
H. Peter Anvin [Thu, 21 Jul 2011 18:22:21 +0000 (11:22 -0700)]
x86: Make Dell Latitude E6420 use reboot=pci
Yet another variant of the Dell Latitude series which requires
reboot=pci.
From the E5420 bug report by Daniel J Blueman:
> The E6420 is affected also (same platform, different casing and
> features), which provides an external confirmation of the issue; I can
> submit a patch for that later or include it if you prefer:
> http://linux.koolsolutions.com/2009/08/04/howto-fix-linux-hangfreeze-during-reboots-and-restarts/
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Daniel J Blueman [Fri, 13 May 2011 01:04:59 +0000 (09:04 +0800)]
x86: Make Dell Latitude E5420 use reboot=pci
Rebooting on the Dell E5420 often hangs with the keyboard or ACPI
methods, but is reliable via the PCI method.
[ hpa: this was deferred because we believed for a long time that the
recent reshuffling of the boot priorities in commit
660e34cebf0a11d54f2d5dd8838607452355f321 fixed this platform.
Unfortunately that turned out to be incorrect. ]
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1305248699-2347-1-git-send-email-daniel.blueman@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Linus Torvalds [Thu, 21 Jul 2011 18:07:18 +0000 (11:07 -0700)]
Merge branch 'drm-intel-fixes' of git://git./linux/kernel/git/keithp/linux-2.6
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
drm/i915: Fix unfenced alignment on pre-G33 hardware
drm/i915: Add quirk to disable SSC on Lenovo U160 LVDS
Linus Torvalds [Thu, 21 Jul 2011 18:01:42 +0000 (11:01 -0700)]
vfs: drop conditional inode prefetch in __do_lookup_rcu
It seems to hurt performance in real life. Yes, the inode will be used
later, but the conditional doesn't seem to predict all that well
(negative dentries are not uncommon) and it looks like the cost of
prefetching is simply higher than depending on the cache doing the right
thing.
As usual.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jan Beulich [Thu, 21 Jul 2011 14:02:43 +0000 (15:02 +0100)]
FS-Cache: Fix __fscache_uncache_all_inode_pages()'s outer loop
The compiler, at least for ix86 and m68k, validly warns that the
comparison:
next <= (loff_t)-1
is always true (and it's always true also for x86-64 and probably all
other arches - as long as pgoff_t isn't wider than loff_t). The
intention appears to be to avoid wrapping of "next", so rather than
eliminating the pointless comparison, fix the loop to indeed get exited
when "next" would otherwise wrap.
On m68k the following warning is observed:
fs/fscache/page.c: In function '__fscache_uncache_all_inode_pages':
fs/fscache/page.c:979: warning: comparison is always false due to limited range of data type
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Suresh Jayaraman <sjayaraman@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Shilovsky [Wed, 20 Jul 2011 14:24:09 +0000 (18:24 +0400)]
CIFS: Fix wrong length in cifs_iovec_read
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Linus Torvalds [Wed, 20 Jul 2011 22:56:25 +0000 (15:56 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
signal: align __lock_task_sighand() irq disabling and RCU
softirq,rcu: Inform RCU of irq_exit() activity
sched: Add irq_{enter,exit}() to scheduler_ipi()
rcu: protect __rcu_read_unlock() against scheduler-using irq handlers
rcu: Streamline code produced by __rcu_read_unlock()
rcu: Fix RCU_BOOST race handling current->rcu_read_unlock_special
rcu: decrease rcu_report_exp_rnp coupling with scheduler
Linus Torvalds [Wed, 20 Jul 2011 22:55:48 +0000 (15:55 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Avoid creating superfluous NUMA domains on non-NUMA systems
sched: Allow for overlapping sched_domain spans
sched: Break out cpu_power from the sched_group structure
Linus Torvalds [Wed, 20 Jul 2011 22:33:59 +0000 (15:33 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86. reboot: Make Dell Latitude E6320 use reboot=pci
x86, doc only: Correct real-mode kernel header offset for init_size
x86: Disable AMD_NUMA for 32bit for now
Ingo Molnar [Wed, 20 Jul 2011 18:59:26 +0000 (20:59 +0200)]
Merge branch 'rcu/urgent' of git://git./linux/kernel/git/paulmck/linux-2.6-rcu into core/urgent
Paul E. McKenney [Tue, 19 Jul 2011 10:25:36 +0000 (03:25 -0700)]
signal: align __lock_task_sighand() irq disabling and RCU
The __lock_task_sighand() function calls rcu_read_lock() with interrupts
and preemption enabled, but later calls rcu_read_unlock() with interrupts
disabled. It is therefore possible that this RCU read-side critical
section will be preempted and later RCU priority boosted, which means that
rcu_read_unlock() will call rt_mutex_unlock() in order to deboost itself, but
with interrupts disabled. This results in lockdep splats, so this commit
nests the RCU read-side critical section within the interrupt-disabled
region of code. This prevents the RCU read-side critical section from
being preempted, and thus prevents the attempt to deboost with interrupts
disabled.
It is quite possible that a better long-term fix is to make rt_mutex_unlock()
disable irqs when acquiring the rt_mutex structure's ->wait_lock.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Peter Zijlstra [Tue, 19 Jul 2011 22:32:00 +0000 (15:32 -0700)]
softirq,rcu: Inform RCU of irq_exit() activity
The rcu_read_unlock_special() function relies on in_irq() to exclude
scheduler activity from interrupt level. This fails because exit_irq()
can invoke the scheduler after clearing the preempt_count() bits that
in_irq() uses to determine that it is at interrupt level. This situation
can result in failures as follows:
$task IRQ SoftIRQ
rcu_read_lock()
/* do stuff */
<preempt> |= UNLOCK_BLOCKED
rcu_read_unlock()
--t->rcu_read_lock_nesting
irq_enter();
/* do stuff, don't use RCU */
irq_exit();
sub_preempt_count(IRQ_EXIT_OFFSET);
invoke_softirq()
ttwu();
spin_lock_irq(&pi->lock)
rcu_read_lock();
/* do stuff */
rcu_read_unlock();
rcu_read_unlock_special()
rcu_report_exp_rnp()
ttwu()
spin_lock_irq(&pi->lock) /* deadlock */
rcu_read_unlock_special(t);
Ed can simply trigger this 'easy' because invoke_softirq() immediately
does a ttwu() of ksoftirqd/# instead of doing the in-place softirq stuff
first, but even without that the above happens.
Cure this by also excluding softirqs from the
rcu_read_unlock_special() handler and ensuring the force_irqthreads
ksoftirqd/# wakeup is done from full softirq context.
[ Alternatively, delaying the ->rcu_read_lock_nesting decrement
until after the special handling would make the thing more robust
in the face of interrupts as well. And there is a separate patch
for that. ]
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Peter Zijlstra [Tue, 19 Jul 2011 22:07:25 +0000 (15:07 -0700)]
sched: Add irq_{enter,exit}() to scheduler_ipi()
Ensure scheduler_ipi() calls irq_{enter,exit} when it does some actual
work. Traditionally we never did any actual work from the resched IPI
and all magic happened in the return from interrupt path.
Now that we do do some work, we need to ensure irq_{enter,exit} are
called so that we don't confuse things.
This affects things like timekeeping, NO_HZ and RCU, basically
everything with a hook in irq_enter/exit.
Explicit examples of things going wrong are:
sched_clock_cpu() -- has a callback when leaving NO_HZ state to take
a new reading from GTOD and TSC. Without this
callback, time is stuck in the past.
RCU -- needs in_irq() to work in order to avoid some nasty deadlocks
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Paul E. McKenney [Mon, 18 Jul 2011 04:14:35 +0000 (21:14 -0700)]
rcu: protect __rcu_read_unlock() against scheduler-using irq handlers
The addition of RCU read-side critical sections within runqueue and
priority-inheritance lock critical sections introduced some deadlock
cycles, for example, involving interrupts from __rcu_read_unlock()
where the interrupt handlers call wake_up(). This situation can cause
the instance of __rcu_read_unlock() invoked from interrupt to do some
of the processing that would otherwise have been carried out by the
task-level instance of __rcu_read_unlock(). When the interrupt-level
instance of __rcu_read_unlock() is called with a scheduler lock held
from interrupt-entry/exit situations where in_irq() returns false,
deadlock can result.
This commit resolves these deadlocks by using negative values of
the per-task ->rcu_read_lock_nesting counter to indicate that an
instance of __rcu_read_unlock() is in flight, which in turn prevents
instances from interrupt handlers from doing any special processing.
This patch is inspired by Steven Rostedt's earlier patch that similarly
made __rcu_read_unlock() guard against interrupt-mediated recursion
(see https://lkml.org/lkml/2011/7/15/326), but this commit refines
Steven's approach to avoid the need for preemption disabling on the
__rcu_read_unlock() fastpath and to also avoid the need for manipulating
a separate per-CPU variable.
This patch avoids need for preempt_disable() by instead using negative
values of the per-task ->rcu_read_lock_nesting counter. Note that nested
rcu_read_lock()/rcu_read_unlock() pairs are still permitted, but they will
never see ->rcu_read_lock_nesting go to zero, and will therefore never
invoke rcu_read_unlock_special(), thus preventing them from seeing the
RCU_READ_UNLOCK_BLOCKED bit should it be set in ->rcu_read_unlock_special.
This patch also adds a check for ->rcu_read_unlock_special being negative
in rcu_check_callbacks(), thus preventing the RCU_READ_UNLOCK_NEED_QS
bit from being set should a scheduling-clock interrupt occur while
__rcu_read_unlock() is exiting from an outermost RCU read-side critical
section.
Of course, __rcu_read_unlock() can be preempted during the time that
->rcu_read_lock_nesting is negative. This could result in the setting
of the RCU_READ_UNLOCK_BLOCKED bit after __rcu_read_unlock() checks it,
and would also result it this task being queued on the corresponding
rcu_node structure's blkd_tasks list. Therefore, some later RCU read-side
critical section would enter rcu_read_unlock_special() to clean up --
which could result in deadlock if that critical section happened to be in
the scheduler where the runqueue or priority-inheritance locks were held.
This situation is dealt with by making rcu_preempt_note_context_switch()
check for negative ->rcu_read_lock_nesting, thus refraining from
queuing the task (and from setting RCU_READ_UNLOCK_BLOCKED) if we are
already exiting from the outermost RCU read-side critical section (in
other words, we really are no longer actually in that RCU read-side
critical section). In addition, rcu_preempt_note_context_switch()
invokes rcu_read_unlock_special() to carry out the cleanup in this case,
which clears out the ->rcu_read_unlock_special bits and dequeues the task
(if necessary), in turn avoiding needless delay of the current RCU grace
period and needless RCU priority boosting.
It is still illegal to call rcu_read_unlock() while holding a scheduler
lock if the prior RCU read-side critical section has ever had either
preemption or irqs enabled. However, the common use case is legal,
namely where then entire RCU read-side critical section executes with
irqs disabled, for example, when the scheduler lock is held across the
entire lifetime of the RCU read-side critical section.
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Peter Zijlstra [Wed, 20 Jul 2011 16:42:57 +0000 (18:42 +0200)]
sched: Avoid creating superfluous NUMA domains on non-NUMA systems
When creating sched_domains, stop when we've covered the entire
target span instead of continuing to create domains, only to
later find they're redundant and throw them away again.
This avoids single node systems from touching funny NUMA
sched_domain creation code and reduces the risks of the new
SD_OVERLAP code.
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Anton Blanchard <anton@samba.org>
Cc: mahesh@linux.vnet.ibm.com
Cc: benh@kernel.crashing.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1311180177.29152.57.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Fri, 15 Jul 2011 08:35:52 +0000 (10:35 +0200)]
sched: Allow for overlapping sched_domain spans
Allow for sched_domain spans that overlap by giving such domains their
own sched_group list instead of sharing the sched_groups amongst
each-other.
This is needed for machines with more than 16 nodes, because
sched_domain_node_span() will generate a node mask from the
16 nearest nodes without regard if these masks have any overlap.
Currently sched_domains have a sched_group that maps to their child
sched_domain span, and since there is no overlap we share the
sched_group between the sched_domains of the various CPUs. If however
there is overlap, we would need to link the sched_group list in
different ways for each cpu, and hence sharing isn't possible.
In order to solve this, allocate private sched_groups for each CPU's
sched_domain but have the sched_groups share a sched_group_power
structure such that we can uniquely track the power.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-08bxqw9wis3qti9u5inifh3y@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Thu, 14 Jul 2011 11:00:06 +0000 (13:00 +0200)]
sched: Break out cpu_power from the sched_group structure
In order to prepare for non-unique sched_groups per domain, we need to
carry the cpu_power elsewhere, so put a level of indirection in.
Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-qkho2byuhe4482fuknss40ad@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Wed, 20 Jul 2011 05:10:28 +0000 (22:10 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix file mode calculation
Linus Torvalds [Wed, 20 Jul 2011 05:10:05 +0000 (22:10 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
davinci: DM365 EVM: fix video input mux bits
ARM: davinci: Check for NULL return from irq_alloc_generic_chip
arm: davinci: Fix low level gpio irq handlers' argument
Shaohua Li [Tue, 19 Jul 2011 15:49:26 +0000 (08:49 -0700)]
vmscan: fix a livelock in kswapd
I'm running a workload which triggers a lot of swap in a machine with 4
nodes. After I kill the workload, I found a kswapd livelock. Sometimes
kswapd3 or kswapd2 are keeping running and I can't access filesystem,
but most memory is free.
This looks like a regression since commit
08951e545918c159 ("mm: vmscan:
correct check for kswapd sleeping in sleeping_prematurely").
Node 2 and 3 have only ZONE_NORMAL, but balance_pgdat() will return 0
for classzone_idx. The reason is end_zone in balance_pgdat() is 0 by
default, if all zones have watermark ok, end_zone will keep 0.
Later sleeping_prematurely() always returns true. Because this is an
order 3 wakeup, and if classzone_idx is 0, both balanced_pages and
present_pages in pgdat_balanced() are 0. We add a special case here.
If a zone has no page, we think it's balanced. This fixes the livelock.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akinobu Mita [Tue, 19 Jul 2011 15:49:25 +0000 (08:49 -0700)]
fs/libfs.c: fix simple_attr_write() on 32bit machines
Assume that /sys/kernel/debug/dummy64 is debugfs file created by
debugfs_create_x64().
# cd /sys/kernel/debug
# echo 0x1234567812345678 > dummy64
# cat dummy64
0x0000000012345678
# echo 0x80000000 > dummy64
# cat dummy64
0xffffffff80000000
A value larger than INT_MAX cannot be written to the debugfs file created
by debugfs_create_u64 or debugfs_create_x64 on 32bit machine. Because
simple_attr_write() uses simple_strtol() for the conversion.
To fix this, use simple_strtoll() instead.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 20 Jul 2011 04:50:21 +0000 (21:50 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: fix race in rcu lookup of pruned dentry
Fix cifs_get_root()
[ Edited the last commit to get rid of a 'unused variable "seq"'
warning due to Al editing the patch. - Linus ]
Linus Torvalds [Mon, 18 Jul 2011 22:43:29 +0000 (15:43 -0700)]
vfs: fix race in rcu lookup of pruned dentry
Don't update *inode in __follow_mount_rcu() until we'd verified that
there is mountpoint there. Kudos to Hugh Dickins for catching that
one in the first place and eventually figuring out the solution (and
catching a braino in the earlier version of patch).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Paul E. McKenney [Sat, 21 May 2011 12:57:18 +0000 (05:57 -0700)]
rcu: Streamline code produced by __rcu_read_unlock()
Given some common flag combinations, particularly -Os, gcc will inline
rcu_read_unlock_special() despite its being in an unlikely() clause.
Use noinline to prohibit this misoptimization.
In addition, move the second barrier() in __rcu_read_unlock() so that
it is not on the common-case code path. This will allow the compiler to
generate better code for the common-case path through __rcu_read_unlock().
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Paul E. McKenney [Thu, 14 Jul 2011 19:24:11 +0000 (12:24 -0700)]
rcu: Fix RCU_BOOST race handling current->rcu_read_unlock_special
The RCU_BOOST commits for TREE_PREEMPT_RCU introduced an other-task
write to a new RCU_READ_UNLOCK_BOOSTED bit in the task_struct structure's
->rcu_read_unlock_special field, but, as noted by Steven Rostedt, without
correctly synchronizing all accesses to ->rcu_read_unlock_special.
This could result in bits in ->rcu_read_unlock_special being spuriously
set and cleared due to conflicting accesses, which in turn could result
in deadlocks between the rcu_node structure's ->lock and the scheduler's
rq and pi locks. These deadlocks would result from RCU incorrectly
believing that the just-ended RCU read-side critical section had been
preempted and/or boosted. If that RCU read-side critical section was
executed with either rq or pi locks held, RCU's ensuing (incorrect)
calls to the scheduler would cause the scheduler to attempt to once
again acquire the rq and pi locks, resulting in deadlock. More complex
deadlock cycles are also possible, involving multiple rq and pi locks
as well as locks from multiple rcu_node structures.
This commit fixes synchronization by creating ->rcu_boosted field in
task_struct that is accessed and modified only when holding the ->lock
in the rcu_node structure on which the task is queued (on that rcu_node
structure's ->blkd_tasks list). This results in tasks accessing only
their own current->rcu_read_unlock_special fields, making unsynchronized
access once again legal, and keeping the rcu_read_unlock() fastpath free
of atomic instructions and memory barriers.
The reason that the rcu_read_unlock() fastpath does not need to access
the new current->rcu_boosted field is that this new field cannot
be non-zero unless the RCU_READ_UNLOCK_BLOCKED bit is set in the
current->rcu_read_unlock_special field. Therefore, rcu_read_unlock()
need only test current->rcu_read_unlock_special: if that is zero, then
current->rcu_boosted must also be zero.
This bug does not affect TINY_PREEMPT_RCU because this implementation
of RCU accesses current->rcu_read_unlock_special with irqs disabled,
thus preventing races on the !SMP systems that TINY_PREEMPT_RCU runs on.
Maybe-reported-by: Dave Jones <davej@redhat.com>
Maybe-reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Paul E. McKenney [Sun, 17 Jul 2011 09:05:49 +0000 (02:05 -0700)]
rcu: decrease rcu_report_exp_rnp coupling with scheduler
PREEMPT_RCU read-side critical sections blocking an expedited grace
period invoke rcu_report_exp_rnp(). When the last such critical section
has completed, rcu_report_exp_rnp() invokes the scheduler to wake up the
task that invoked synchronize_rcu_expedited() -- needlessly holding the
root rcu_node structure's lock while doing so, thus needlessly providing
a way for RCU and the scheduler to deadlock.
This commit therefore releases the root rcu_node structure's lock before
calling wake_up().
Reported-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Sage Weil [Tue, 19 Jul 2011 18:25:04 +0000 (11:25 -0700)]
ceph: fix file mode calculation
open(2) must always include one of O_RDONLY, O_WRONLY, or O_RDWR. No need
for any O_APPEND special case.
Passing O_WRONLY|O_RDWR is undefined according to the man page, but the
Linux VFS interprets this as O_RDWR, so we'll do the same.
This fixes open(2) with flags O_RDWR|O_APPEND, which was incorrectly being
translated to readonly.
Reported-by: Fyodor Ustinov <ufm@ufm.su>
Signed-off-by: Sage Weil <sage@newdream.net>
Jon Povey [Tue, 19 Jul 2011 03:30:11 +0000 (12:30 +0900)]
davinci: DM365 EVM: fix video input mux bits
Video input mux settings for tvp7002 and imager inputs were swapped.
Comment was correct.
Tested on EVM with tvp7002 input.
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: stable@kernel.org
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Todd Poynor [Sun, 17 Jul 2011 05:39:35 +0000 (22:39 -0700)]
ARM: davinci: Check for NULL return from irq_alloc_generic_chip
Avoid NULL dereference of irq_alloc_generic_chip return in low
memory conditions.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Chris Wilson [Mon, 18 Jul 2011 20:11:49 +0000 (13:11 -0700)]
drm/i915: Fix unfenced alignment on pre-G33 hardware
Align unfenced buffers on older hardware to the power-of-two object
size. The docs suggest that it should be possible to align only to a
power-of-two tile height, but using the already computed fence size is
easier and always correct. We also have to make sure that we unbind
misaligned buffers upon tiling changes.
In order to prevent a repetition of this bug, we change the interface
to the alignment computation routines to force the caller to provide
the requested alignment and size of the GTT binding rather than assume
the current values on the object.
Reported-and-tested-by: Sitosfe Wheeler <sitsofe@yahoo.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=36326
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Keith Packard <keithp@keithp.com>
Linus Torvalds [Mon, 18 Jul 2011 20:29:26 +0000 (13:29 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
pppoe: Must flush connections when MAC address changes too.
include/linux/sdla.h: remove the prototype of sdla()
tulip: dmfe: Remove old log spamming pr_debugs
David S. Miller [Mon, 18 Jul 2011 18:48:28 +0000 (11:48 -0700)]
pppoe: Must flush connections when MAC address changes too.
Kernel bugzilla: 39252
Signed-off-by: David S. Miller <davem@davemloft.net>
WANG Cong [Sat, 16 Jul 2011 22:22:20 +0000 (22:22 +0000)]
include/linux/sdla.h: remove the prototype of sdla()
`make headers_check` complains that
linux-2.6/usr/include/linux/sdla.h:116: userspace cannot reference
function or variable defined in the kernel
this is due to that there is no such a kernel function,
void sdla(void *cfg_info, char *dev, struct frad_conf *conf, int quiet);
I don't know why we have it in a kernel header, so remove it.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Mon, 18 Jul 2011 17:50:40 +0000 (13:50 -0400)]
Fix cifs_get_root()
Add missing ->i_mutex, convert to lookup_one_len() instead of
(broken) open-coded analog, cope with getting something like
a//b as relative pathname. Simplify the hell out of it, while
we are there...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Joe Perches [Mon, 18 Jul 2011 17:44:44 +0000 (10:44 -0700)]
tulip: dmfe: Remove old log spamming pr_debugs
Commit
726b65ad444d ("tulip: Convert uses of KERN_DEBUG") enabled
some old previously inactive uses of pr_debug converted by
commit
dde7c8ef1679 ("tulip/dmfe.c: Use dev_<level> and pr_<level>").
Remove these pr_debugs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mauro Carvalho Chehab [Sun, 17 Jul 2011 03:24:37 +0000 (00:24 -0300)]
si4713-i2c: avoid potential buffer overflow on si4713
While compiling it with Fedora 15, I noticed this issue:
inlined from ‘si4713_write_econtrol_string’ at drivers/media/radio/si4713-i2c.c:1065:24:
arch/x86/include/asm/uaccess_32.h:211:26: error: call to ‘copy_from_user_overflow’ declared with attribute error: copy_from_user() buffer size is not provably correct
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 18 Jul 2011 16:05:59 +0000 (09:05 -0700)]
Merge branch 'fix/asoc' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Correct WM8994 MICBIAS supply widget hookup
ASoC: Fix shift in WM8958 accessory detection default implementation
ASoC: sh: fsi-hdmi: fixup snd_soc_card name
ASoC: sh: fsi-da7210: fixup snd_soc_card name
ASoC: sh: fsi-ak4642: fixup snd_soc_card name
Linus Torvalds [Mon, 18 Jul 2011 16:03:15 +0000 (09:03 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
hppfs_lookup(): don't open-code lookup_one_len()
hppfs: fix dentry leak
cramfs: get_cramfs_inode() returns ERR_PTR() on failure
ufs should use d_splice_alias()
fix exofs ->get_parent()
ceph analog of cifs build_path_from_dentry() race fix
cifs: build_path_from_dentry() race fix
Linus Torvalds [Mon, 18 Jul 2011 16:02:58 +0000 (09:02 -0700)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (max1111) Fix race condition causing NULL pointer exception
hwmon: (it87) Fix label group removal
hwmon: (asus_atk0110) Fix memory leak
Al Viro [Mon, 18 Jul 2011 02:27:22 +0000 (22:27 -0400)]
hppfs_lookup(): don't open-code lookup_one_len()
... and it's getting it wrong, too - missing ->d_revalidate() calls when
it's dealing with filesystem (procfs) that has non-trivial ->d_revalidate()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 18 Jul 2011 02:24:15 +0000 (22:24 -0400)]
hppfs: fix dentry leak
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 17 Jul 2011 23:04:14 +0000 (19:04 -0400)]
cramfs: get_cramfs_inode() returns ERR_PTR() on failure
... and we want to report these failures in ->lookup() anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 17 Jul 2011 14:07:34 +0000 (10:07 -0400)]
ufs should use d_splice_alias()
it's NFS-exportable, so...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sat, 9 Jul 2011 00:56:55 +0000 (20:56 -0400)]
fix exofs ->get_parent()
NULL is not a possible return value for that method, TYVM...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 17 Jul 2011 19:49:55 +0000 (12:49 -0700)]
Merge git://git./linux/kernel/git/sfrench/cifs-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] update cifs to version 1.74
[CIFS] update limit for snprintf in cifs_construct_tcon
cifs: Fix signing failure when server mandates signing for NTLMSSP
Linus Torvalds [Sun, 17 Jul 2011 19:49:28 +0000 (12:49 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
Bluetooth: Fix crash with incoming L2CAP connections
Bluetooth: Fix regression in L2CAP connection procedure
gianfar: rx parser
r6040: only disable RX interrupt if napi_schedule_prep is successful
net: remove NETIF_F_ALL_TX_OFFLOADS
net: sctp: fix checksum marking for outgoing packets
Linus Torvalds [Sun, 17 Jul 2011 19:48:52 +0000 (12:48 -0700)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: hpwdt depends on PCI
watchdog: fix hpwdt Kconfig regression in 3.0-rc
Linus Torvalds [Sun, 17 Jul 2011 19:48:18 +0000 (12:48 -0700)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] tuner-core: fix a 2.6.39 regression with mt20xx
[media] dvb_frontend: fix race condition in stopping/starting frontend
[media] media: fix radio-sf16fmr2 build when SND is not enabled
[media] MEDIA: Fix non-ISA_DMA_API link failure of sound code
[media] nuvoton-cir: make idle timeout more sane
[media] mceusb: increase default timeout to 100ms
[media] mceusb: Timeout unit corrections
[media] Revert "V4L/DVB: cx23885: Enable Message Signaled Interrupts(MSI)"