wifi: rtw89: refine scan function after chanctx

Since we can get the current channel definition each interface maps to,
remove store_op function that is no longer required to make things simple.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-3-pkshih@realtek.com

wifi: rtw89: prohibit enter IPS during HW scan

Mac80211 core may ask driver to change to idle mode during HW scan,
then H2C command for HW scan will send failed since chip is in idle
mode. Therefore, We check the SCANNING flag before entering IPS to
prevent this behavior.

Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230415034900.15679-2-pkshih@realtek.com

wifi: rtw89: coex: send more hardware module info to firmware for 8851B

8851B has various hardware module types, so BT coexistence in firmware
needs these information to make decision. Add them to make 8851B work
well.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-5-pkshih@realtek.com

wifi: rtw89: coex: Update function to get BT RSSI and hardware counter

Correct Bluetooth RSSI count method. The 6dB is the gap between hardware
packet sampled value and real RSSI value.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-4-pkshih@realtek.com

wifi: rtw89: coex: Add path control register to monitor list

Chips use similar hardware for path control, but could different
path/antenna configuration. Add these register to monitor, if there are
wrong settings, these register can help to debug.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-3-pkshih@realtek.com

wifi: rtw89: coex: Enable Wi-Fi RX gain control for free run solution

When Wi-Fi & Bluetooth are both busy at the same time, Wi-Fi need to
enable RX gain to protect Wi-Fi RX RF ability. Without this configure
the interference from Bluetooth will bring a big impact to Wi-Fi RX.

Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230412012831.10519-2-pkshih@realtek.com

wifi: rtw89: fix power save function in WoWLAN mode

In WoWLAN Mode, it's expected that WiFi chip could enter power save mode
only after all setting is finished, but current wow_enter_lps function
break the rule and may lead to WoWLAN function fail in low probability,
so fix it.

Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230410053438.10682-2-pkshih@realtek.com

wifi: rtw89: support WoWLAN mode for 8852be

To support WoWLAN mode for 8852be, we add one PLE quota setting and
WoWLAN stub, which shows that supported WLAN events include receiving
magic packet, rekey packet and deauth packet, and disconnecting from AP.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230410053438.10682-1-pkshih@realtek.com

wifi: iwlwifi: move debug buffer allocation failure to info verbosity

This is noising the kernel log and customers asked to hush it down.
We can live with this message in "info" verbosity.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.0a7f557aa2a0.If9db474b63242b1bfaed659aa174b678ae8dc196@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: make the loop for card preparation effective

Since we didn't reset t to 0, only the first iteration of the loop
did checked the ready bit several times.
From the second iteration and on, we just tested the bit once and
continued to the next iteration.

Reported-and-tested-by: Lorenzo Zolfanelli <lorenzo@zolfa.nl>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216452
Fixes: 289e5501c314 ("iwlwifi: fix the preparation of the card")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.615b683ab9c8.Ic52c3229d3345b0064fa34263293db095d88daf8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: allow number of beacons from FW

Newer firmware images have a TLV advertising how many
beacons they support, use that to permit adding more
links in AP mode (FW needs to support at least as many
links as beacons).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.0d7522533557.Ic6b5992e94446c35cb0f3add019defa6e7aded2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: implement key link switching

Implement switching keys from one set of firmware station IDs
to another set, during link switch.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.c6a777dd5e47.I693f7fd7c52fe8b51a58af69d45488511367f49e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: implement BAID link switching

When we switch station links, also add the code to switch
BAIDs from one station mask to the new one.

To do so, refactor the switching code a bit to have common
code for all the needed switches; will add keys next.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.40654afce24f.I0e35151f69e7513be53ddb8f008e9ab48278c352@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: track station mask for BAIDs

When we have MLO connections, a BAID applies to multiple
firmware stations. Track the station mask instead of the
station ID, getting rid of a few more deflink cases and
preparing for handling link switching for BAIDs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.c08523808c34.I719b7bba499648d1495ed3e3a90889d4732ef15d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: bump FW API to 77 for AX devices

Start supporting API version 77 for AX devices.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.e522ccefe354.If7628363fafeb7687163103e734206915c445197@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: use correct sta mask to remove queue

When we remove a queue we need to use the currently active
firmware stations in the mask, not the deflink one. Fix that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.01cdd2153418.I176d54f2d869f51b3707d056adb96455cf885f93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: avoid iterating over an un-initialized list

The initiator smooth list is initialized only in iwl_mvm_up(), but is
cleared in iwl_mvm_mac_stop. This may result in iterating over the
list before it was initialized in case iwl_mvm_up() failed early.
Fix it by moving the list initialization to an earlier stage.

Fixes: b68bd2e3143a ("iwlwifi: mvm: Add FTM initiator RTT smoothing logic")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.b50b1fe9a576.Ie348ffae110612d2e252ac120a3ba0aea063b1b6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: factor out iwl_mvm_sta_fw_id_mask()

We are going to need this in more places than just the
key code, so factor out the functionality of getting
the FW station ID mask (filtered to a specific link if
needed) to a separate function that can now be called
both under RCU and mvm->mutex protection.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.eff92b93025d.I2c50290a0537d5db3d3460f4d57c78a4712ffb75@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: properly implement HE AP support

The firmware split the HE support field into HE and "pseudo HE",
the latter is really for AP and doesn't implement trigger frame
handling for example.

Use the new field for AP mode.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.34dbfefe2a49.I0e39cd35dbe03ff9209b26733746479eae1c8966@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: Fix _iwl_mvm_get_scan_type()

The usage of the 'dtim_period' value was wrong, as it is only
a multiplier of the beacon interval, and thus, beacon interval should
also be considered. Fix it.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.e08293d6cace.I25f8cea3189472bd714676ca38b121d7c60fb9d9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: fix getting lowest TX rate for MLO

In iwl_mvm_mac_ctxt_get_lowest_rate() we were still accessing
vif->bss_conf without any multi-link provisions, and also the
info->band, both of which isn't valid in MLO.

Fix the code to look at the correct link. In case of EAPOL
transmissions for the initial 4-way-HS, look up the correct
link here as well, and warn if multiple are active.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.d892f68d3bcd.I7d6927abeea5c3899db225391dbc6a5c77805e80@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: call napi_synchronize() before freeing rx/tx queues

When rx/tx queues are being freed, on a different CPU there could be
still rx flow running. Call napi_synchronize() to prevent such a race.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Co-developed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Link: https://lore.kernel.org/r/20230416154301.5171ee44dcc1.Iff18718540da412e084e7d8266447d40730600ed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: nvm-parse: add full BW UL MU-MIMO support

For some devices, in client mode, we support full bandwidth
uplink multi-user MIMO. Add the necessary capability.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.88b6aac6c876.Ibf2a7a38d7a172c371c347c9d4441e8c656cefe3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

bcma: Add explicit of_device.h include

bcma/main.c uses of_dma_configure() which is declared in of_device.h.
of_device.h gets implicitly included by of_platform.h, but that is going
to be removed soon.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230410232701.1561613-1-robh@kernel.org

wifi: rtl8xxxu: Support devices with 5-6 out endpoints

Handle them the same way as the devices with 3-4 USB out endpoints.
This is needed for the RTL8192FU.

Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/ef4bc66d-84f5-4021-efd7-1787d097519c@gmail.com

wifi: rtl8xxxu: Clean up some messy ifs

Add some new members to rtl8xxxu_fileops and use them instead of
checking priv->rtl_chip.

Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e24a5534-6e33-cfb9-0634-0caf4646513f@gmail.com

wifi: brcmfmac: add Cypress 43439 SDIO ids

Add SDIO ids for use with the muRata 1YN (Cypress CYW43439).
The odd thing about this is that the previous 1YN populated
on M.2 card for evaluation purposes had BRCM SDIO vendor ID,
while the chip populated on real hardware has a Cypress one.
The device ID also differs between the two devices. But they
are both 43439 otherwise, so add the IDs for both.

On-device 1YN (43439), the new one, chip label reads "1YN":
```
/sys/.../mmc_host/mmc2/mmc2:0001 # cat vendor device
0x04b4
0xbd3d
```

EA M.2 evaluation board 1YN (43439), the old one, chip label reads "1YN ES1.4":
```
/sys/.../mmc_host/mmc0/mmc0:0001/# cat vendor device
0x02d0
0xa9a6
```

Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230407203752.128539-1-marex@denx.de

wifi: rtw89: fix crash due to null pointer of sta in AP mode

In AP mode, 'sta' could be NULL if sending broadcast/multicast packets,
so we should check before accessing, or it causes crash:

  BUG: kernel NULL pointer dereference, address: 0000000000000004
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  PGD 0 P4D 0
  Oops: 0000 [#1] PREEMPT SMP PTI
  CPU: 2 PID: 92 Comm: kworker/u33:0 Tainted: G           OE
  Workqueue: rtw89_tx_wq rtw89_core_txq_work [rtw89_core]
  RIP: 0010:rtw89_core_tx_update_desc_info+0x2cc/0x7d0 [rtw89_core]
  Code: e2 01 41 be 04 00 00 00 41 8b 84 c4 0c 01 00 00 75 0d 45 31 f6 ...
  RSP: 0018:ffffb4cf807afce0 EFLAGS: 00010297
  RAX: 0000000000000001 RBX: ffffb4cf807afd48 RCX: 0000000000000000
  RDX: 0000000000000000 RSI: 0000000000000001 RDI: 0000000000000001
  RBP: ffffb4cf807afd30 R08: ffff9b28c1e59808 R09: ffff9b28c0297100
  R10: 00000000052cf7c4 R11: 00000000052cf7c4 R12: ffff9b28c1602040
  R13: ffff9b28c07b3000 R14: 0000000000000004 R15: 0000000000000000
  FS:  0000000000000000(0000) GS:ffff9b2a73280000(0000) knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000004 CR3: 00000001ca410003 CR4: 00000000000606e0
  Call Trace:
   <TASK>
   rtw89_core_tx_write+0x7c/0x100 [rtw89_core]
   rtw89_core_txq_work+0x1b4/0x530 [rtw89_core]
   process_one_work+0x222/0x3f0
   worker_thread+0x50/0x3f0
   kthread+0x16b/0x190
   ? rescuer_thread+0x3a0/0x3a0
   ? set_kthread_struct+0x50/0x50
   ret_from_fork+0x22/0x30
   </TASK>

Fixes: e5307c9cd7ee ("wifi: rtw89: set data lowest rate according to AP supported rate")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230406093009.5869-1-pkshih@realtek.com

wifi: rtw89: correct 5 MHz mask setting

Use primary channel index to determine which 5 MHz mask should be enable.
This mask is used to prevent noise from channel edge to effect CCA
threshold in wide bandwidth (>= 40 MHZ).

Fixes: 1b00e9236a71 ("rtw89: 8852c: add set channel of BB part")
Fixes: 6b0698984eb0 ("wifi: rtw89: 8852b: add chip_ops::set_channel")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230406072841.8308-1-pkshih@realtek.com

wifi: rtw89: 8851b: add tables for RFK

These tables are used by RF calibrations to assist to configure PHY and
RF registers.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-4-pkshih@realtek.com

wifi: rtw89: 8851b: add BB and RF tables (2 of 2)

These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.

Internal version of these tables:
 - HALBB_029_106_15 (V17)
 - HALRF_029_00_089
   * Radio A 0x22
   * NCTL 0x5

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-3-pkshih@realtek.com

wifi: rtw89: 8851b: add BB and RF tables (1 of 2)

These tables contain BB and RF parameters that driver will load them into
registers. It also contains TX power according to country, band, rate and
so on. Increasing thermal can cause TX power degraded, so power tracking
tables are defined to compensate TX power.

Internal version of these tables:
 - HALBB_029_106_15 (V17)
 - HALRF_029_00_089
   * Radio A 0x22
   * NCTL 0x5

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230401142548.55466-2-pkshih@realtek.com

wifi: rtw89: pci: update PCI related settings to support 8851B

Many settings of 8851B are like 8852A or 8852B. Change them to proper
settings as hardware design.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-5-pkshih@realtek.com

wifi: rtw89: mac: update MAC settings to support 8851b

Many settings of 8851B are the same as 8852B or 8852A, like DLE (Data link
engine), security engine and so on. Update them according to hardware
design.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-4-pkshih@realtek.com

wifi: rtw89: 8851b: fix TX path to path A for one RF path chip

For two RF paths chips, we normally set path B as main path by default.
8851B has single one RF path, so set TX path to A and set mapping of
path B to 0.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-3-pkshih@realtek.com

wifi: rtw89: read version of analog hardware

The chip contains digital and analog parts, and each of them has its own
version number. This is used by BT coexistence mechanism to make strategy
decision for different analog version.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330133324.19538-2-pkshih@realtek.com

wifi: rtw89: use hardware CFO to improve performance

Turn on hardware CFO (central frequency offset) compensation based on IC
capability, and improve digital CFO compensation accuracy by using
more fixed points number.

Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330132352.13647-1-pkshih@realtek.com

wifi: rtw89: support parameter tables by RFE type

One chip can have different RFE (RF front end) types which we will judge
at runtime. And, different RFE types may use different RF parameter tables.
Though we didn't really meet this case previously, we are going to meet it
on upcoming chip RTL8851B. So, this commit handles parameter tables for
runtime RFE type.

We now encapsulate rtw89_txpwr_rule_<2/5/6>ghz tables into rtw89_rfe_parms.
Then, each chip defines its default parameter tables, and if needed, it can
configure extra parameter tables by RFE type. Finally we determine runtime
parameter tables by RFE type if one is configured. Otherwise, we use the
default parameter tables.

For now, we just move all settings under default parameter tables. We will
configure parameter tables by RFE types in separate commits afterwards.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230330080331.37155-1-pkshih@realtek.com

wifi: rtw89: add firmware format version to backward compatible with older drivers

In the discuss threads [1] [2], new firmware format break user space
because older drivers can't recognize new firmware format. To avoid this,
the new format will be named rtw89/rtw8852b_fw-1.bin and only new driver
try to load it. Old drivers only load original and understandable firmware
rtw89/rtw8852b_fw.bin.

More, new driver will be still backward compatible with old firmware, so
original firmware can be used by new driver.

If there is newer firmware format is introduced, rtw89/rtw8852b_fw-2.bin
will be given. The same rules will be applied like above. So, we will have
firmware like below in linux-firmware in the future.

  rtw89/rtw8852b_fw-2.bin
  rtw89/rtw8852b_fw-1.bin
  rtw89/rtw8852b_fw.bin

After this patch, MODULE_FIRMWARE() of 8852A/B/C become
  rtw89/rtw8852a_fw.bin
  rtw89/rtw8852b_fw-1.bin
  rtw89/rtw8852c_fw.bin

[1] https://lore.kernel.org/linux-wireless/df1ce994-3368-a57e-7078-8bdcccf4a1fd@gmail.com/T/#m24cb43be31a762d0ea70bf07f27ae96c59f6931b
[2] https://bugzilla.kernel.org/show_bug.cgi?id=217207

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-4-pkshih@realtek.com

wifi: rtw89: use schedule_work to request firmware

Since we are going to load more than one firmware and some are not
presented or optional, using asynchronous API request_firmware_nowait()
will become complicated. Also, we want to use firmware_request_nowarn()
to avoid warning messages when loading optional files. So, use
schedule_work to be simpler.

To abstract loading a firmware or file, define a struct rtw89_fw_req_info
containing a struct firmware and a completion to ensure this firmware is
loaded completely.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-3-pkshih@realtek.com

wifi: rtw89: fw: use generic flow to set/check features

In early feature bitmap obtained from rtw89_early_fw_feature_recognize(),
the bits needed to check get increased. It's more friendly to work with
RTW89_CHK_FW_FEATURE(). So, we concentrate the flow of iterating FW feature
configures and calling RTW89_SET_FW_FEATURE() for various uses. And then,
we adjust rtw89_early_fw_feature_recognize() for RTW89_CHK_FW_FEATURE().

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230320130606.20777-2-pkshih@realtek.com

wifi: rtw89: fix authentication fail during scan

We used to store operating channel info after associated. However, scan
might happen before that. Without switching back to operating channel,
authentication or association might fail. Therefore, we switch back to
operating channel when the scanning vif's BSSID is non-zero, which
implies connected or during attempt to connect.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-6-pkshih@realtek.com

wifi: rtw89: add flag check for power state

Use POWER_ON flag to make sure power on/off is symmetric. Since both
remain_on_channel and hw_scan both alter the power state, this makes
sure that we don't enter/leave IPS mode twice.
Also, replace IPS related functions with inline function that does
similar logic so we can track it more easily.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-5-pkshih@realtek.com

wifi: rtw89: add ieee80211::remain_on_channel ops

Add support of remain on channel ops. Since channel context is
required to enable multi-channel concurrent(MCC) and the current
ROC in mac80211 don't support more than 1 channel context, add this
to let P2P and other protocols relying on this work as expected.
The off-channel duration and cancel timing is purely controlled by
upper layers.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-4-pkshih@realtek.com

wifi: rtw89: add function to wait for completion of TX skbs

Allocate a per-skb completion to track those skbs we are interested in
and wait for them to complete transmission with TX status.

Normally, the completion object is freed by wait side, but it could be
timeout result that complete side should free the object instead. Add a
owner field with RCU to determine which side should free the object.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-3-pkshih@realtek.com

wifi: rtw89: 8852c: add beacon filter and CQM support

Adding this supports beacon filter and connection quality monitor.
To make host CPU wake up less, let firmware perform signal
monitoring and beacon processing, then notify driver upon signal
changes or beacon loss.

This feature needs firmware 0.27.56 or newer to support it.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230411124832.14965-2-pkshih@realtek.com

wifi: iwlwifi: mvm: tx: remove misleading if statement

The if statement here is misleading, we return zero anyway
since we just checked the 'ret' variable, simplify the code
to remove the condition entirely.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.57c1eb58e655.I1b47a7771cd66306931089c150c6b5b240bdcba5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: Fix setting the rate for non station cases

The setting of the rate used for non station cases did not take into
consideration the interface type etc., thus when probe responses
are transmitted on P2P Device interface etc. CCK rates were used
which is not allowed.

Modify the code so the non station case would consider the
interface type etc. For HWs/FWs that do not support rate control,
preserve the previous behavior, i.e., take the rate from the
skb metadata and adjust as needed.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.fa0e4d42205d.Iab4784560c77b965fec070d4d0a1ec84171d94ff@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: validate station properly in flush

If we have MLO, then the deflink.ap_sta_id cannot be used.
However, we can use the new mvmvif->ap_sta pointer for the
validation instead.

Also don't do it multiple times for different FW instances
of the same AP STA (TDLS STAs are only on a single link).

Note that this isn't really working right yet since the
underlying flush code hasn't been updated yet to know of
multiple link STAs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.7d747df44d65.Ie5392859fab4cfb73c20b49bfee2caadef5fd8ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: set STA mask for keys in MLO

Implement the full STA mask and selecting the correct link
for key installation.

While at it, catch errors if this function returns a bad
zero station mask, rather than waiting for the firmware to
crash on it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.cedae2f21829.Iae07b736c3109d085ad5b74ec8282ce45020da39@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: fix ptk_pn memory leak

If adding a key to firmware fails we leak the allocated ptk_pn.
This shouldn't happen in practice, but we should still fix it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.99446ffd02bc.I82a2ad6ec1395f188e0a1677cc619e3fcb1feac9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: make iwl_mvm_mac_ctxt_send_beacon() static

We never needed this to be non-static, that was just an
artifact of the development process. Make it static.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.3c018c15f948.I87fd1aee288f33312a7206492608002d4e8e213e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: track AP STA pointer and use it for MFP

Instead of relying on the AP STA ID and dereferencing our
firmware -> mac80211 STA array when we really only need
the STA, not the per-link information (and might not have
it, e.g. for a pairwise key installation where this is
relevant), keep track of the AP STA as a pointer to the
mac80211 STA, protected by the mutex. Then use it here in
the key code instead.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.7db01b1508de.I88e6d252cdb0a6e4581d7c5fd7cbc037b4fd40ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: pcie: Fix integer overflow in iwl_write_to_user_buf

An integer overflow occurs in the iwl_write_to_user_buf() function,
which is called by the iwl_dbgfs_monitor_data_read() function.

static bool iwl_write_to_user_buf(char __user *user_buf, ssize_t count,
  void *buf, ssize_t *size,
  ssize_t *bytes_copied)
{
int buf_size_left = count - *bytes_copied;

buf_size_left = buf_size_left - (buf_size_left % sizeof(u32));
if (*size > buf_size_left)
*size = buf_size_left;

If the user passes a SIZE_MAX value to the "ssize_t count" parameter,
the ssize_t count parameter is assigned to "int buf_size_left".
Then compare "*size" with "buf_size_left" . Here, "buf_size_left" is a
negative number, so "*size" is assigned "buf_size_left" and goes into
the third argument of the copy_to_user function, causing a heap overflow.

This is not a security vulnerability because iwl_dbgfs_monitor_data_read()
is a debugfs operation with 0400 privileges.

Signed-off-by: Hyunwoo Kim <imv4bel@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.2d80ace81532.Iecfba549e0e0be21bbb0324675392e42e75bd5ad@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: fw: move memset before early return

Clang static analysis reports this representative issue
dbg.c:1455:6: warning: Branch condition evaluates to
a garbage value
  if (!rxf_data.size)
       ^~~~~~~~~~~~~~

This check depends on iwl_ini_get_rxf_data() to clear
rxf_data but the function can return early without
doing the clear.  So move the memset before the early
return.

Fixes: cc9b6012d34b ("iwlwifi: yoyo: use hweight_long instead of bit manipulating")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.872a7175f1ff.I33802a77a91998276992b088fbe25f61c87c33ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: initialize seq variable

Clang static analysis reports this issue
d3.c:567:22: warning: The left operand of '>' is
  a garbage value
  if (seq.tkip.iv32 > cur_rx_iv32)
      ~~~~~~~~~~~~~ ^

seq is never initialized. Call ieee80211_get_key_rx_seq() to
initialize seq.

Fixes: 0419e5e672d6 ("iwlwifi: mvm: d3: separate TKIP data from key iteration")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.6dd372f84f93.If1f708c90e6424a935b4eba3917dfb7582e0dd0a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: Fix spelling mistake "Gerenal" -> "General"

There is a spelling mistake in a IWL_DEBUG_SCAN debug message. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.eac55cbef8f1.I15cc5d3f1489759bf915bfb3cbbb72b67b18f8b6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Fix spelling mistake "upto" -> "up to"

There is a spelling mistake in a IWL_ERR error message. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.a00965734d02.I760cb43829b3d7a0f567f0958059f2fae0aa8a93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: enable new MLD FW API

Enable the new FW API with MLD based on FW TLV.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.5dc66b08539e.I1c65024c879346b0349e1e431d36ec2b5fd85dd7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: add a new PCI device ID for BZ device

Add support for a new PCI device ID 0x272b once registering with PCIe.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.56342664110d.I5aa6f2858fdcf69fdea4f1a873115a48bd43764e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Add RF Step Type for BZ device

Add RF step id handling and handle for BZ device.
Read CNV Aux register and uses for no OTP case.
Add missing rf support for Bz/Bnj device and correct/add
the mapping for rf-type if OTP not present.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230414130637.8f2e2fff7bbc.Iee5554178bc5f134dcc28591db0968e619afbdca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: scan legacy bands and UHB channels with same antenna

In case of UHB scan that follows a scan on legacy bands,
consider both scan commands as part of the same scan cycle,
and thus configure them to use the same antenna configuration.

Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.fd582c423ad8.I35239f94cb3ee1642d16936199c336a07ec2df8f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: yoyo: Fix possible division by zero

Don't allow buffer allocation TLV with zero req_size since it
leads later to division by zero in iwl_dbg_tlv_alloc_fragments().
Also, NPK/SRAM locations are allowed to have zero buffer req_size,
don't discard them.

Fixes: a9248de42464 ("iwlwifi: dbg_ini: add TLV allocation new API support")
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.5d6688ed74d8.I5c2f3a882b50698b708d54f4524dc5bdf11e3d32@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: yoyo: skip dump correctly on hw error

When NIC is in a bad state, reading data will return 28 bits as
0xa5a5a5a and the lowest 4 bits are not fixed value.

Mask these bits in a few places to skip the dump correctly.

Fixes: 89639e06d0f3 ("iwlwifi: yoyo: support for new DBGI_SRAM region")
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.df6c0663179d.I36d8487b2419c6fefa65e5514855d94327c3b1eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: pcie: fix possible NULL pointer dereference

It is possible that iwl_pci_probe() will fail and free the trans,
then afterwards iwl_pci_remove() will be called and crash by trying
to access trans which is already freed, fix it.

iwlwifi 0000:01:00.0: Detected crf-id 0xa5a5a5a2, cnv-id 0xa5a5a5a2
      wfpm id 0xa5a5a5a2
iwlwifi 0000:01:00.0: Can't find a correct rfid for crf id 0x5a2
...
BUG: kernel NULL pointer dereference, address: 0000000000000028
...
RIP: 0010:iwl_pci_remove+0x12/0x30 [iwlwifi]
pci_device_remove+0x3e/0xb0
device_release_driver_internal+0x103/0x1f0
driver_detach+0x4c/0x90
bus_remove_driver+0x5c/0xd0
driver_unregister+0x31/0x50
pci_unregister_driver+0x40/0x90
iwl_pci_unregister_driver+0x15/0x20 [iwlwifi]
__exit_compat+0x9/0x98 [iwlwifi]
__x64_sys_delete_module+0x147/0x260

Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.082f6e21341b.I0db21d7fa9a828d571ca886713bd0b5d0b6e1e5c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Fix the duplicate dump name

Driver is using the dump name generated first time in all
generated dump in case of NMI.
The validity of dump name should be with each dump created
and need to reset after each use.

Fixes: 834f920ef34b ("wifi: iwlwifi: yoyo: Add driver defined dump file name")
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.6c987f820557.I924f2eae1eef2fe82c7a23be566551653d46f729@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: pcie: work around ROM bug on AX210 integrated

On 22000 and AX210 devices, there's a ROM bug that causes it to
set invalid LTR settings. On 22000 and AX210 non-integrated we
can fix up these settings from the driver (as done in the code
here), but on AX210 integrated these registers are not available
to the driver.

Attempt to work around the issue by spinning while the IML is
being loaded, the IML will then reprogram the LTR values itself
after it's loaded, so only the brief IML load (which the ROM is
doing) is affected.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.aaa0a4339984.If08da23e960b6236f8c05c06fc8b26041ac89f1e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: add DSM_FUNC_ENABLE_6E value to debugfs

In order to simplify checking that this value was set up
correctly, add it to debugfs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.c9a787710e1e.If509b2e510e22d62f3eefb2c54ff1645e331dc23@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: cleanup beacon_inject_active during hw restart

beacon_inject_active turns true and false via debugfs when we inject a
beacon. During the time of the beacon injection we can't configure the
FW with a beacon cmd. If we have a hw restart during the beacon injection
then in the recovery flow we will not be able to configure the beacon
cmd to the FW. Fix this by cleaning up this variable after an hw restart.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.b021bce5e162.Ia5a0a0b5d8734f63077ceaac936176a345f8d3d1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: support wowlan info notification version 2

As part of version 2 we don't need to have wake_packet_bufsize
and wake_packet_length. The first one is already calculated by the driver,
the latter is sent as part of the wake packet notification.

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.3b53213b10d4.Ibf2f15aca614def2d262dd267d1aad65931b58f1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: make HLTK configuration for PASN station optional

When secure LTF is not used, the HLTK is not derived during the PASN
authentication. Make the HLTK optional when adding a PASN station.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.a57f7f3b59bd.Ifa88afb51a2516156153ac321d81556e295036c2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: request limiting to 8 MSDUs per A-MSDU

Due to hardware limitations when splitting up A-MSDUs, it
cannot handle an arbitrary number of MSDUs per A-MSDU. Set
the bits to ask transmitters to send only 8 MSDUs in one
A-MSDU.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.e6c518f2724f.I15c13d13b38289edbcd64f67d57cf18f6026457a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: fix shift-out-of-bounds

The aux queue is initialized to IWL_MVM_INVALID_QUEUE. This is
later used for a bitmask of the queue, which results in a
shift-out-of-bounds. Fix it.

Fixes: b85f7ebb2497 ("wifi: iwlwifi: mvm: avoid UB shift of snif_queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.c41a33c32898.Idc15f9eed005345a4137c28ef62efd80a405fad0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: acpi: support modules with high antenna gain

Starting from version 4 of ANT_GAIN_CMD verification of ppag table
values is done by the FW. Driver has to send the complete table as
it appears in the BIOS. Make this change.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.a965365e2336.I1081f00ae309d9225d0529fa2da6ba7e34a8bd4f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: don't drop unencrypted MCAST frames

MCAST frames are filtered out by the driver if we are not
authorized yet.
Fix it to filter out only protected frames.

Fixes: 147eb05f24e6 ("iwlwifi: mvm: always tell the firmware to accept MCAST frames in BSS")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.9cedcc27db60.I8fb7057981392660da482dd215e85c15946d3f4b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: dbg: print pc register data once fw dump occurred

Add debug print for different FW program counter details of
different CPU. Program counter pc details will be read from
TLV during init.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413213309.862790d336a9.I34e2ea05a79e8b2552f7f221bacf3af0166cb9c0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: add flush_sta method

Some drivers like iwlwifi might have per-STA queues, so we
may want to flush/drop just those queues rather than all
when removing a station. Add a separate method for that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: flush queues on STA removal

When we remove a station, we first make it unreachable,
then we (must) remove its keys, and then remove the
station itself. Depending on the hardware design, if
we have hardware crypto at all, frames still sitting
on hardware queues may then be transmitted without a
valid key, possibly unencrypted or with a fixed key.

Fix this by flushing the queues when removing stations
so this cannot happen.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: ieee80211: correctly mark FTM frames non-bufferable

The checks of whether or not a frame is bufferable were not
taking into account that some action frames aren't, such as
FTM. Check this, which requires some changes to the function
ieee80211_is_bufferable_mmpdu() since we need the whole skb
for the checks now.

Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: ieee80211: clean up public action codes

WLAN_PUBLIC_ACTION_FTM_RESPONSE is duplicated with
WLAN_PUB_ACTION_FTM, but that might better be called
WLAN_PUB_ACTION_FTM_RESPONSE; clean up here.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: don't set CHECKSUM_COMPLETE for unsupported protocols

On Bz devices, CHECKSUM_COMPLETE was set for unsupported protocols
which results in a warning. Fix it.

Fixes: b6f5b647f694 ("iwlwifi: mvm: handle RX checksum on Bz devices")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.a2a35286f0ca.I50daa9445a6465514c44f5096c32adef64beba5f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: trans: don't trigger d3 interrupt twice

When the IPC registers are used for sleep control, setting
the IPC sleep bit already triggers an interrupt to the fw, so
there is no need to also set the doorbell. Setting also the
doorbell triggers the sleep interrupt twice which lead to
an assert.

Fixes: af08571d3925 ("iwlwifi: pcie: support Bz suspend/resume trigger")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.b5f2f6e44d38.I4cb5b6ad4914db47a714e731c4c8b4db679cabce@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Update configurations for Bnj-a0 and specific rf devices

Correction in config data is done for loading the ucode.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.879b654c8d83.I7dbea9f411a0b6f47908c4ad6321c7e55cbeb636@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Update init sequence if tx diversity supported

PHY configuration command need to be sent to FW if the tx diversity
with SISO is supported.
This need to be sent to get the init notification from FW.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.c2121c8694a7.Ibee3dd8765ef4b7504660fa228a7c7eff78920af@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: move function sequence

Need to move a function definition and actual changes
will be done in following commit.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.00a6c203712f.I7c099e5c1954f1daa5a5039b98149b6f081e46ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: nvm: Update HE capabilities on 6GHz band for EHT device

Max A-MPDU length exponent shall be set to 2 for EHT capable
device on 6GHz band in order to support 4MB aggregation.

Update HE MAC capabilities accordingly for station and softap
interfaces.

This change requires to add another ieee80211_sband_iftype_data for
uhb since high/uhb are no longer the same.

Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.1eee32cfd199.I9c5ff3a6956d509137deca620814935149516fbc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: refactor TX csum mode check

There are two modes now, and we have two places checking
that must be in sync. Refactor the logic into a new small
helper function.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.ef6246f4b73b.I44820ec095634dd0bba3007465cf25e4ce1c77c6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: fix A-MSDU checks

Since Gl A-step devices use the old checksum hardware,
we shouldn't use the Bz code to check for A-MSDU
combining ability; fix that.

Fixes: ec18e7d4d20d ("wifi: iwlwifi: mvm: use old checksum for Bz A-step")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.8c445b943fee.Ibf772102ca712f59e2ee0cdd4c344011fcf445aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: enable bz hw checksum from c step

B step doesn't support full checksum yet, move to c step.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.697a9d74e84d.I6724874112692a04e29287cac9dad7140532557f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: use OFDM rate if IEEE80211_TX_CTL_NO_CCK_RATE is set

IEEE80211_TX_CTL_NO_CCK_RATE indicates that CCK rates should not be
used, but is ignored by the driver. Fix it.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.a322d18b5eb1.Icc46027a03f90feffb6fab49a5d82e54829d3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: convert TID to FW value on queue remove

On queue remove, we should convert the TID value to the
firmware value (8 -> 15) just like we do on queue add.
Otherwise, the firmware will not be able to find the
correct queue to remove.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.6651077eaec3.Ia6868c8fc1a92063609bb057b6a618726712d0bb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Update configuration for SO,SOF MAC and HR RF

update the device configuration for HR1 device for SO and SOF device.
QuZ device configuration is corrected to support specific CRF.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.86f08520323f.Ieccb50de47f877b85732000a0d67b645eeeb0c2a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: add a validity check of queue_id in iwl_txq_reclaim

This function receives the queue id to reclaim packets from. Currently
we're passing to it the queue id we received from the FW in the flush
response. We don't do any check of this value and it might be invalid.
In such case we will refer to a pointer to a queue which might be NULL.
Fix this by adding a validity check of the queue id before using it.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.a9c3fd32bce7.I5fbdcf3b1b80eb96a907116c166f19dc0aae7cb8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: nvm-parse: enable 160/320 MHz for AP mode

Initially, 160/320 MHz in AP mode were not supported.
After testing, enable the wider bandwidths in AP mode
as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.ed04de3a2833.Ie3991179dfaf24880b96a0904a625dbf6b8fd579@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: debug: fix crash in __iwl_err()

In __iwl_err(), if we rate-limit the message away, then
vaf.va is still NULL-initialized by the time we get to
the tracing code, which then crashes. When it doesn't
get rate-limited out, it's still wrong to reuse the old
args2 that was already printed, which is why we bother
making a copy in the first place.

Assign vaf.va properly to fix this.

Fixes: e5f1cc98cc1b ("iwlwifi: allow rate-limited error messages")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.e27134c6bcd4.Ib3894cd2ba7a5ad5e75912a7634f146ceaa569e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: rtw88: Add support for the SDIO based RTL8821CS chipset

Wire up RTL8821CS chipset support using the new rtw88 SDIO HCI code as
well as the existing RTL8821C chipset code.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-10-martin.blumenstingl@googlemail.com

wifi: rtw88: Add support for the SDIO based RTL8822CS chipset

Wire up RTL8822CS chipset support using the new rtw88 SDIO HCI code as
well as the existing RTL8822C chipset code.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-9-martin.blumenstingl@googlemail.com

wifi: rtw88: Add support for the SDIO based RTL8822BS chipset

Wire up RTL8822BS chipset support using the new rtw88 SDIO HCI code as
well as the existing RTL8822B chipset code.

Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-8-martin.blumenstingl@googlemail.com

mmc: sdio: add Realtek SDIO vendor ID and various wifi device IDs

Add the SDIO vendor ID for Realtek and some device IDs extracted from
their GPL vendor driver. This will be useful in the future when the
rtw88 driver gains support for these chips.

Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-7-martin.blumenstingl@googlemail.com

wifi: rtw88: main: Reserve 8 bytes of extra TX headroom for SDIO cards

For SDIO host controllers with DMA support the TX buffer physical memory
address need to be aligned at an 8-byte boundary. Reserve 8 bytes of
extra TX headroom so we can align the data without re-allocating the
transmit buffer.

While here, also remove the TODO comment regarding extra headroom for
USB and SDIO. For SDIO the extra headroom is now handled and for USB it
was not needed so far.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230405200729.632435-6-martin.blumenstingl@googlemail.com