Rajeshwari Birje [Thu, 26 Dec 2013 04:14:18 +0000 (09:44 +0530)]
Exynos5420: Add base addresses for 5420
Adds base addresses of various IPs and controllers required for
Exynos5420.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Birje [Thu, 26 Dec 2013 04:14:17 +0000 (09:44 +0530)]
EXYNOS5: Create a common board file
Create a common board.c file for all functions which are common across
all EXYNOS5 platforms.
exynos_init function is provided for platform specific code.
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:24 +0000 (15:02 +0530)]
ARM: AM43xx: Add Maintainer
Adding Maintainer for AM43xx.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:23 +0000 (15:02 +0530)]
ARM: AM43xx: GP_EVM: Add support for DDR3
GP EVM has 1GB DDR3 attached(Part no: MT41K512M8RH).
Adding details for the same.
Below is the brief description of DDR3 init sequence(SW leveling):
-> Enable VTT regulator
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program leveling registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:22 +0000 (15:02 +0530)]
ARM: AM43xx: EPOS_EVM: Add support for LPDDR2
AM4372 EPOS EVM has 1GB LPDDR2(Part no: MT42L256M32D2LG-25 WT:A)
Adding LPDDR2 init sequence and register details for the same.
Below is the brief description of LPDDR2 init sequence:
-> Configure VTP
-> Configure DDR IO settings
-> Disable initialization and refreshes until EMIF registers are programmed.
-> Program Timing registers
-> Program PHY control and Temp alert and ZQ config registers.
-> Enable initialization and refreshes and configure SDRAM CONFIG register
-> Wait till initialization is complete and the configure MR registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:21 +0000 (15:02 +0530)]
ARM: AM33xx+: Update ioregs to pass different values
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:20 +0000 (15:02 +0530)]
ARM: AM43xx: clocks: Update DPLL details
Updating the Multiplier and Dividers value for all DPLLs.
Safest OPP is read from DEV ATTRIBUTE register. Accoring to the value
returned the MPU DPLL is locked.
At different OPPs follwoing are the MPU locked frequencies.
OPP50 300MHz
OPP100 600MHz
OPP120 720MHz
OPPTB 800MHz
OPPNT 1000MHz
According to the latest DM following is the OPP table dependencies:
VDD_CORE VDD_MPU
OPP50 OPP50
OPP50 OPP100
OPP100 OPP50
OPP100 OPP100
OPP100 OPP120
So at different OPPs of MPU it is safest to lock CORE at OPP_NOM.
Following are the DPLL locking frequencies at OPP NOM:
Core locks at 1000MHz
Per locks at 960MHz
LPDDR2 locks at 266MHz
DDR3 locks at 400MHz
Touching AM33xx files also to get DPLL values specific to board but no
functionality difference.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:19 +0000 (15:02 +0530)]
ARM: AM43xx: mux: Update mux data
Updating the mux data for UART, adding data for i2c0 and mmc.
And also updating pad_signals structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:18 +0000 (15:02 +0530)]
ARM: AM43xx: Update Current Booting devices list
Current Booting devices list is different from that of AM33xx.
Updating the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:17 +0000 (15:02 +0530)]
ARM: AM43xx: Select clk source for Timer2
Selecting the Master osc clk as Timer2 clock source.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sekhar Nori [Tue, 10 Dec 2013 09:32:16 +0000 (15:02 +0530)]
ARM: AM43XX: Add CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG support
CONFIG_ENV_VARS_UBOOT_CONFIG, CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and
CONFIG_BOARD_LATE_INIT is already set. Adding support to detect the
board. These variables are used by findfdt.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Sekhar Nori [Tue, 10 Dec 2013 09:32:15 +0000 (15:02 +0530)]
ARM: AM43XX: board: add support for reading onboard EEPROM
Add support for reading onboard EEPROM to enable
board detection.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:14 +0000 (15:02 +0530)]
ARM: AM43xx: Add extra ENV settings
Add Extra env settings.
This is derived from am335x Extra ENV settings.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:13 +0000 (15:02 +0530)]
ARM: AM43xx: Add L2 Support
AM4372 uses PL310 L2 Cache. Enable the configs for the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:12 +0000 (15:02 +0530)]
ARM: AM43xx: Adapt to ti_armv7_common.h config file
Use ti_armv7_common.h config file to inclde the common
configs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Tue, 10 Dec 2013 09:32:11 +0000 (15:02 +0530)]
ARM: AM43xx: Update the base addresses of modules
PRCM, timer base addresses and offsets are different from
AM33xx. Updating the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Stefan Roese [Tue, 17 Dec 2013 13:14:06 +0000 (14:14 +0100)]
arm: omap3: Fix beagleboard SPL boot hangup (GPIO clocks not enabled)
Patch
f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Beagleboard. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Albert ARIBAUD [Wed, 18 Dec 2013 21:19:02 +0000 (22:19 +0100)]
Merge remote-tracking branch 'u-boot-pxa/master' into 'u-boot-arm/master'
Albert ARIBAUD [Wed, 18 Dec 2013 20:45:34 +0000 (21:45 +0100)]
Merge branch 'u-boot-tegra/master' into 'u-boot-arm/master'
Marek Vasut [Mon, 4 Nov 2013 19:50:21 +0000 (20:50 +0100)]
ARM: pxa: Fix CONFIG_SYS_HZ on PXA
The PXA incorrectly uses CONFIG_SYS_HZ, which should be 1000 across
U-Boot. Fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Alban Bedel [Wed, 20 Nov 2013 16:42:46 +0000 (17:42 +0100)]
arm: tegra: Fix the CPU complex reset masks
The CPU complex reset masks are not matching with the datasheet for
the CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET/CLR_0 registers. For both T20
and T30 the register consist of groups of 4 bits, with one bit for
each CPU core. On T20 the 2 high bits of each group are always stubbed
as there is only 2 cores.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swrren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Alban Bedel [Thu, 14 Nov 2013 09:58:30 +0000 (10:58 +0100)]
ARM: tegra: Add the Tamonten™ NG Evaluation Carrier board
Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Alban Bedel [Wed, 13 Nov 2013 16:27:19 +0000 (17:27 +0100)]
i2c: tegra: Add the fifth bus on SoC with more than 4 buses
Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Alban Bedel [Wed, 13 Nov 2013 16:27:18 +0000 (17:27 +0100)]
ARM: tegra: support SKU b1 of Tegra30
Add the Tegra30 SKU b1 and treat it like other Tegra30 chips.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Julian Scheel <julian.scheel@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Jim Lin [Wed, 6 Nov 2013 06:03:44 +0000 (14:03 +0800)]
ARM: config: USB: Tegra30/114: Fix EHCI timeout issue on "bootp"
Fix the timeout issue after running "bootp" command in u-boot
console. For example you see "EHCI timed out on TD- token=0x...".
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10
after a controller reset and before RUN bit is set
(per technical reference manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Vidya Sagar [Thu, 31 Oct 2013 09:21:38 +0000 (14:51 +0530)]
tegra: allow build to succeed with SPL disabled
u-boot-dtb-tegra.bin and u-boot-nodtb-tegra.bin binaries
are generated only if the SPL build is enabled as they have
dependency on SPL build
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Mon, 23 Sep 2013 09:52:41 +0000 (11:52 +0200)]
Change maintainer for Avionic Design boards
I no longer work for Avionic Design and don't have access to hardware,
so I'll pass on maintainership to Alban.
Acked-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Thierry Reding [Tue, 1 Oct 2013 15:04:45 +0000 (17:04 +0200)]
Tegra114: Do not program CPCON field for PLLX
PLLX no longer has the CPCON field on Tegra114, so do not attempt to
program it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Jimmy Zhang [Mon, 23 Sep 2013 20:07:49 +0000 (22:07 +0200)]
Tegra114: Fix PLLX M, N, P init settings
The M, N and P width have been changed from Tegra30. The maximum value
for N is limited to 255. So, the tegra_pll_x_table for Tegra114 should
be set accordingly.
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Reviewed-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sergei Ianovich [Tue, 17 Dec 2013 01:03:44 +0000 (05:03 +0400)]
arm: pxa: init ethaddr for LP-8x4x using DT
When DT define aliases for etherner0 and ethernet1, U-Boot
automatically patched MAC addresses using ethaddr and eth1addr
environment variables respectively.
Custom initialization is no longer needed.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
Sergei Ianovich [Tue, 17 Dec 2013 01:03:43 +0000 (05:03 +0400)]
arm: pxa: update LP-8x4x to boot DT kernel
DT kernel requires CONFIG_OF_LIBFDT. 'bootm' needs to know DT location.
In addition, fix kernel console device and enable U-Boot long help.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
Sergei Ianovich [Tue, 17 Dec 2013 01:03:42 +0000 (05:03 +0400)]
arm: pxa: fix 2nd flash chip address on LP-8x4x
Initial configuration has worng address of the second chip.
There is an alias for the 1st chip at 0x02000000 in earlier
verions of LP-8x4x, so the boot normally.
However, new LP-8x4xs have a bigger 1st flash chip, and hang on
boot without this patch.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
Sergei Ianovich [Wed, 18 Dec 2013 16:19:20 +0000 (20:19 +0400)]
arm: pxa: fix LP-8x4x USB support
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
Albert ARIBAUD [Wed, 18 Dec 2013 16:51:28 +0000 (17:51 +0100)]
Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'
Sergei Ianovich [Tue, 17 Dec 2013 01:03:40 +0000 (05:03 +0400)]
ARM: pxa: prevent PXA270 occasional reboot freezes
Erratum 71 of PXA270M Processor Family Specification Update
(April 19, 2010) explains that watchdog reset time is just
8us insead of 10ms in EMTS.
If SDRAM is not reset, it causes memory bus congestion and
the device hangs.
We put SDRAM in selfresh mode before watchdog reset, removing
potential freezes.
Signed-off-by: Sergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>
Nobuhiro Iwamatsu [Thu, 10 Oct 2013 01:48:20 +0000 (10:48 +0900)]
arm: koelsch: Add support reset function
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Wed, 11 Sep 2013 06:04:33 +0000 (15:04 +0900)]
arm: koelsch: Add support I2C
This supports sh_i2c on koelsch board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Sun, 20 Oct 2013 11:37:17 +0000 (20:37 +0900)]
arm: koelsch: Add support Ethernet
The koelsch board has one sh-ether device.
This supports sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 10 Oct 2013 00:13:41 +0000 (09:13 +0900)]
arm: lager: Add support reset function
The lager board uses I2C for reset.
ned-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Mon, 30 Sep 2013 01:08:40 +0000 (10:08 +0900)]
arm: lager: Add support I2C
The lager board has I2C for rcar.
This supports I2C for rcar on lager board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Sun, 20 Oct 2013 11:28:24 +0000 (20:28 +0900)]
arm: lager: Add support Ethernet
The lager board has one sh-ether device.
This supports sh-ether.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Tue, 10 Dec 2013 05:52:20 +0000 (14:52 +0900)]
arm: rmobile: Update README.rmobile
Add infomation of Lager and Koelsh board, and R-Car.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Bo Shen [Tue, 10 Dec 2013 08:14:02 +0000 (16:14 +0800)]
arm: atmel: at91sam9x5: move CONFIG_SYS_NO_FLASH to proper position
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Tue, 10 Dec 2013 08:14:01 +0000 (16:14 +0800)]
arm: atmel: at91sam9x5: cleanup unneeded undef
remove unneeded #undef for at91sam9x5ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Tue, 17 Dec 2013 09:34:43 +0000 (17:34 +0800)]
arm: atmel: at91sam9x5: cleanup cs configure for spi
As the cs for spi is worked in gpio mode, so no need to configure
it as peripheral and then configure to gpio. Configure it to gpio
directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Lokesh Vutla [Thu, 12 Dec 2013 10:06:21 +0000 (15:36 +0530)]
ARM: OMAP5: clocks: Update MPU settings for OPP_NOM
As per the latest 0.6 version of DM for OMAP5430 ES2.0,
MPU_GCLK is given as 1000MHz. In order to achieve this DPLL_MPU
should be locked at 2000MHz. Fixing the same and cleaning the
previously used dpll values.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Lokesh Vutla [Thu, 12 Dec 2013 10:04:56 +0000 (15:34 +0530)]
ARM: DRA7xx: Change clk divider setting
Commit "armv7: hw_data: change clock divider setting"
updates the setting for m6 divider for 20MHz sys_clk frequency.
But missed to update for other sys_clk frequencies. Doing the same.
Reported-by: Rajendran, Vinothkumar <vinothr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Nikita Kiryanov [Wed, 11 Dec 2013 16:04:40 +0000 (18:04 +0200)]
arm: omap: cm_t35: update config file
This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
"ULPI: ulpi_reset: failed writing reset bit"
So, remove it.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>
Yegor Yefremov [Wed, 11 Dec 2013 14:41:11 +0000 (15:41 +0100)]
am3517_evm: activate Ethernet PHY
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Heiko Schocher [Tue, 10 Dec 2013 10:56:53 +0000 (11:56 +0100)]
am335x, siemens boards: adapt default environment setting
commit
16297cfb2a20c9d89834cd9e31edac5184a777a1
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Fri Oct 4 19:22:26 2013 +0200
usb: new board-specific USB init interface
introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
Nikita Kiryanov [Sun, 8 Dec 2013 12:29:19 +0000 (14:29 +0200)]
arm: omap: abb: add missing include
ABB code uses LDELAY but does not include the header that provides its
definition.
Include the header.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nishanth Menon <nm@ti.com>
Dan Murphy [Thu, 5 Dec 2013 13:19:17 +0000 (07:19 -0600)]
arm: am437: Fix offset for USB registers
Fix the offset for the USB clock registers
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Tom Rini [Wed, 4 Dec 2013 14:14:20 +0000 (09:14 -0500)]
am335x_evm: Consolidate DFU environment parts into the DFU part of the file
To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: Tom Rini <trini@ti.com>
Stefan Roese [Wed, 4 Dec 2013 12:54:18 +0000 (13:54 +0100)]
arm: omap3: Add SPL support to cm_t35
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Stefan Roese [Wed, 4 Dec 2013 08:27:37 +0000 (09:27 +0100)]
arm: omap3: Add HEAD acoustics (HA) board variant omap3_ha to tao3530
The Head acoustics (HA) baseboard used the Technexion TAO3530 SOM
and has only some minor differences to the Technexion Thunder baseboard.
This patch adds support for this HA baseboard / TAO3530 as the "omap3_ha"
build target.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Stefan Roese [Wed, 4 Dec 2013 08:27:36 +0000 (09:27 +0100)]
arm: omap3: Add board revision output to tao3530
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Stefan Roese [Wed, 4 Dec 2013 08:27:35 +0000 (09:27 +0100)]
arm: omap3: Remove bootargs mem_size handling
The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Stefan Roese [Wed, 4 Dec 2013 08:27:34 +0000 (09:27 +0100)]
arm: omap3: Add SPL support to tao3530
Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Tapani Utriainen [Wed, 4 Dec 2013 08:27:33 +0000 (09:27 +0100)]
arm, omap3: Add support for TechNexion modules
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Lokesh Vutla [Wed, 4 Dec 2013 06:52:55 +0000 (12:22 +0530)]
ARM: OMAP4: Move TEXT_BASE down to non-HS limit
With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html
Tested on OMAP4460 PANDA.
Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tom Rini [Fri, 23 Aug 2013 16:26:49 +0000 (12:26 -0400)]
am33xx: Enable D-CACHE on !CONFIG_SYS_DCACHE_OFF
Test on Beaglebone white over cpsw, usb ether and SD card (read and
write), performance increased, crc32 of data matches.
Signed-off-by: Tom Rini <trini@ti.com>
Jeroen Hofstee [Thu, 21 Nov 2013 21:32:51 +0000 (22:32 +0100)]
ARM: fix the standalone programs
The standalone programs do not use the api calls, but rely
directly on u-boot variable gd->jt for the jump table. Commit
fe1378a - "ARM: use r9 for gd" changed the register holding
the address of gd, but the assembly code in the standalone
examples was not updated accordingly. This broke the programs
on ARM relying on the jumptable in the v2013.10 release.
This patch unbricks them by using the correct register.
Cc: Michal Simek <monstr@monstr.eu>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Albert ARIBAUD [Fri, 8 Nov 2013 21:37:33 +0000 (22:37 +0100)]
Revert "ARM: move interrupt_init to before relocation"
Revert commit
0f5141e9 which causes boards starting in
FLASH to try and write to a FLASH location.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tom Rini [Tue, 10 Dec 2013 22:15:18 +0000 (17:15 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
board/samsung/trats2/trats2.c
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
Albert ARIBAUD [Tue, 10 Dec 2013 13:31:56 +0000 (14:31 +0100)]
Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
arch/arm/cpu/armv7/rmobile/Makefile
doc/README.scrapyard
Needed manual fix:
arch/arm/cpu/armv7/omap-common/Makefile
board/compulab/cm_t335/u-boot.lds
Tom Rini [Tue, 10 Dec 2013 14:36:23 +0000 (09:36 -0500)]
Merge branch 'spi' of git://git.denx.de/u-boot-x86
Tom Rini [Tue, 10 Dec 2013 14:33:13 +0000 (09:33 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
Tom Rini [Tue, 10 Dec 2013 14:29:45 +0000 (09:29 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Ian Campbell [Sun, 17 Nov 2013 15:17:42 +0000 (15:17 +0000)]
vexpress: use correct timer address on extended memory map systems
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: albert.u.boot@aribaud.net
Soren Brinkmann [Wed, 30 Oct 2013 14:49:32 +0000 (15:49 +0100)]
serial: zynq: Remove unused #defines
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mike Frysinger [Tue, 3 Dec 2013 23:43:28 +0000 (16:43 -0700)]
sandbox: spi: Enable new spi/sf layers
We want to test SPI flash code in the sandbox, so enable the new drivers and
the 'sf test' command.
This command is used to validate the sandbox SPI / SPI flash implementation,
so enable it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Mike Frysinger [Tue, 3 Dec 2013 23:43:27 +0000 (16:43 -0700)]
sandbox: spi: Add new SPI flash driver
This adds a SPI flash driver which simulates SPI flash clients.
Currently supports the bare min that U-Boot requires: you can
probe, read, erase, and write. Should be easy to extend to make
it behave more exactly like a real SPI flash, but this is good
enough to merge now.
sjg@chromium.org added a README and tidied up code a little.
Added a required map_sysmem() for sandbox.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Mike Frysinger [Tue, 3 Dec 2013 23:43:26 +0000 (16:43 -0700)]
sandbox: spi: Add SPI emulation bus
This adds a SPI framework for people to hook up simulated SPI clients.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 3 Dec 2013 23:43:25 +0000 (16:43 -0700)]
spi: Add device tree binding for SPI bus
This was obtained from Linux 3.12 commit
5e01dc7b26.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 3 Dec 2013 23:43:24 +0000 (16:43 -0700)]
spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT node
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 3 Dec 2013 23:43:23 +0000 (16:43 -0700)]
sandbox: Rename sb_cmdline_option to sandbox_cmdline_option
The new name is longer but more clearly related to sandbox.
This is in a separate patch within the same series since some comments on the
SPI series rely on it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hung-ying Tyan <tyanh@chromium.org>
Mateusz Kulikowski [Mon, 2 Dec 2013 22:30:58 +0000 (23:30 +0100)]
arm: at91: support for the Calao USB-A9263 board (based on AT91SAM9263)
Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Mon, 2 Dec 2013 06:47:23 +0000 (07:47 +0100)]
arm, at91: add siemens corvus board
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Mon, 2 Dec 2013 06:47:22 +0000 (07:47 +0100)]
arm, at91: add Siemens board taurus and axm
enable support for the siemens AT91SAM9G20 based boards taurus
and axm.
Signed-off-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Fri, 29 Nov 2013 11:13:46 +0000 (12:13 +0100)]
at91: switch coloured LED to gpio API
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Fri, 29 Nov 2013 11:13:45 +0000 (12:13 +0100)]
at91: nand: switch atmel_nand to generic GPIO API
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Andreas Bießmann [Fri, 29 Nov 2013 11:13:44 +0000 (12:13 +0100)]
at91: redefine legacy GPIO PIN_BASE
In order to get the very same value for legacy pin definitions and new gpio
definitions set the legacy PIN_BASE to 0.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Andreas Bießmann [Fri, 29 Nov 2013 11:13:43 +0000 (12:13 +0100)]
at91: add new gpio pin definitions
This patch define new names for GPIO pins on at91 devices. Follow up patches
will convert the whole infrastructure to use these new definitions.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Kuo-Jung Su [Mon, 25 Nov 2013 02:51:41 +0000 (10:51 +0800)]
mmc: add Faraday FTSDC021 SDHCI controller support
Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.
However this driver is only verified with SD memory cards.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>
Priyanka Jain [Thu, 28 Nov 2013 04:42:16 +0000 (10:12 +0530)]
powerpc: mmc: Add corenet devices support in esdhc spl
Existing eSDHC SPL framework assumes booting from sd-image
with boot_format header which contains final u-boot Image
offset and size. No such header is present in case of
corenet devices like T1040 as corenet deivces use PBI-RCW
based intialization.
So, for corenet deives, SPL bootloader use values provided
at compilation time. These values can be defined in board
specific config file.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Alexey Brodkin [Wed, 27 Nov 2013 13:00:52 +0000 (17:00 +0400)]
mmc/dwmmc: modify FIFO threshold only if value explicitly set
If platform provides "host->fifoth_val" it will be used for
initialization of DWMCI_FIFOTH register. Otherwise default value will be
used.
This implementation allows:
* escape unclear and recursive calculations that are currently in use
* use whatever custom value for DWMCI_FIFOTH initialization if any
particular SoC requires it
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Amar <amarendra.xt@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Andy Fleming <afleming@freescale.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Jaehoon Chung [Fri, 29 Nov 2013 11:08:57 +0000 (20:08 +0900)]
mmc: dw_mmc: remove the exynos specific code in dw-mmc.c
dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Albert ARIBAUD [Thu, 7 Nov 2013 13:21:46 +0000 (14:21 +0100)]
arm: keep all sections in ELF file
Current LDS files /DISCARD/ a lot of sections when linking ELF
files, causing diagnostic tools such as readelf or objdump to
produce partial output. Keep all section at link stage, filter
only at objcopy time so that .bin remains minimal.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Masahiro Yamada [Mon, 7 Oct 2013 02:46:56 +0000 (11:46 +0900)]
ARM: align MVBAR on 32 byte boundary
The lower 5 bit of MVBAR is UNK/SBZP.
So, Monitor Vector Base Address must be 32-byte aligned.
On the other hand, the secure monitor handler does not need
32-byte alignment.
This commit moves ".algin 5" directive to the correct place.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Andre Przywara <andre.przywara@linaro.org>
Acked-by: Andre Przywara <andre.przywara@linaro.org>
Albert ARIBAUD [Fri, 6 Dec 2013 15:54:42 +0000 (16:54 +0100)]
Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'
Albert ARIBAUD [Fri, 6 Dec 2013 13:26:51 +0000 (14:26 +0100)]
Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'
Tom Rini [Fri, 6 Dec 2013 12:19:09 +0000 (07:19 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-blackfin
Tom Rini [Tue, 6 Dec 2011 15:49:41 +0000 (08:49 -0700)]
AM3517 EVM: Enable ethernet
Signed-off-by: Tom Rini <trini@ti.com>
Roger Quadros [Mon, 2 Dec 2013 13:47:45 +0000 (15:47 +0200)]
omap4_panda: Don't use ulpi_reset
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Roger Quadros [Mon, 2 Dec 2013 13:47:44 +0000 (15:47 +0200)]
omap3_beagle: Don't use ulpi_reset
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Roger Quadros [Mon, 2 Dec 2013 13:47:43 +0000 (15:47 +0200)]
usb: ehci-omap: Reset the USB Host OMAP module
In commit bb1f327 we removed the UHH reset to fix NFS root (over usb
ethernet) problems with Beagleboard (3530 ES1.0). However, this
seems to cause USB detection problems for Pandaboard, about (3/8).
On further investigation, it seems that doing the UHH reset is not
the cause of the original Beagleboard problem, but in the way the reset
was done.
This patch adds proper UHH RESET mechanism for OMAP3 and OMAP4/5 based
on the UHH_REVISION register. This should fix the Beagleboard NFS
problem as well as the Pandaboard USB detection problem.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CC: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Michael Trimarchi [Sat, 30 Nov 2013 06:59:58 +0000 (07:59 +0100)]
arm: omap3: Enable clocks for peripherals only if they are used
This patch change the per_clocks_enable() function used in OMAP3
code to enable peripherals clocks. Only required clock should be
activated. So if the board use the uart(x) as a console we need
to activate it. The Board's config should include define to enable
every subsystem that the board use. For a complete list
of affected peripherals, registers CM_FCLKEN_PER and CM_ICLKEN_PER
should be checked.
Right now the bootloader can enable and disable clocks for:
uart(x) using CONFIG_SYS_NS16550
gpio bank (x) using CONFIG_OMAP3_GPIO_X with X = { 2, 3, 4, 5, 6 }
i2c bus using CONFIG_DRIVER_OMAP34XX_I2C.
Not required gptimer(x) and mcbsp(x) for booting are disabled by default and
are not supported by any define.
Their activation need to included in the per_clocks_enable if the
peripheral is included. Not booting board should enable the peripheral
clock connected to their driver
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Minkyu Kang [Fri, 6 Dec 2013 10:18:13 +0000 (19:18 +0900)]
arm: arndale: disable spi boot
arndale board is booted from mmc
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
Minkyu Kang [Fri, 6 Dec 2013 10:04:03 +0000 (19:04 +0900)]
arm: exynos: adds ifdef for spi boot
This patch fix following errors and warnings
spl_boot.c: In function 'exynos_spi_copy':
spl_boot.c:111:49: error: 'CONFIG_ENV_SPI_BASE' undeclared (first use in this function)
spl_boot.c:111:49: note: each undeclared identifier is reported only once for each function it appears in
spl_boot.c:142:2: error: 'SPI_FLASH_UBOOT_POS' undeclared (first use in this function)
spl_boot.c: In function 'copy_uboot_to_ram':
spl_boot.c:189:28: warning: unused variable 'param' [-Wunused-variable]
spl_boot.c: At top level:
spl_boot.c:107:13: warning: 'exynos_spi_copy' defined but not used [-Wunused-function]
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Albert ARIBAUD [Fri, 6 Dec 2013 09:41:49 +0000 (10:41 +0100)]
Merge branch 'u-boot-sh/rmobile' into 'u-boot-arm/master'
projects / platform / kernel / u-boot.git / log