rockchip: firefly-rk3288: add -u-boot.dtsi

Move U-Boot relate dts node/property into -u-boot.dtsi

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: update u-boot raw image size for all boards

Some rk3288 boards are using raw image of u-boot.bin, and now
it's much bigger than default 200KB, update CONFIG_SYS_MONITOR_LEN
to 600KB.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: fennec-rk3288: add -u-boot.dtsi

Move U-Boot relate dts node/property into -u-boot.dtsi

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: evb-rk3288: add -u-boot.dtsi

Move U-Boot relate dts node/property into -u-boot.dtsi

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: enable TPL for evb-rk3288

Enable TPL for evb-rk3288 so that we can have a free size limited
SPL.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: add default TPL_LDSCRIPT value in Kconfig

We share the same TPL_LDSCRIPT for all rk3288 board, add
default value in Kconfig.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: move configure_l2ctlr back to rk3288

The configure_l2ctlr() is used only by rk3288, do not need to
locate in sys_proto.h

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: add arch_cpu_init in spl

Add arch_cpu_init() in SPL for soc related init, and
move configure_l2ctlr() into it.
The arch_cpu_init() only need to run once, so no need
to run in TPL.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3368: default enable SPL LIBCOMMON and LIBGENERIC

We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk322x: default enable SPL LIBCOMMON and LIBGENERIC

We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3328: default enable SPL LIBCOMMON and LIBGENERIC

We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3399: default enable SPL LIBCOMMON and LIBGENERIC

We needs SPL LIBCOMMON and LIBGENERIC for all boards,
so we can enable them by default and no need to define
in each board.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3368: use defaule value for SYS_MALLOC_F_LEN

There is no difference in rk3368 board use for SYS_MALLOC_F_LEN,
so we can use default value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3328: use defaule value for SYS_MALLOC_F_LEN

There is no difference in rk3328 board use for SYS_MALLOC_F_LEN,
so we can use default value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3399: use default value for SYS_MALLOC_F_LEN

There is no difference in rk3399 board use for SYS_MALLOC_F_LEN,
so we can use default value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: use default value for SYS_MALLOC_F_LEN

There is no difference in rk3288 board use for SYS_MALLOC_F_LEN,
so we can use default value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk322x: use defconfig for SYS_MALLOC_F_LEN

There is no difference in rk322x board use for SYS_MALLOC_F_LEN,
so we can use default value.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: Kconfig: move ROCKCHIP_BOOT_MODE_REG to soc Kconfig

Rockchip SoCs have different ROCKCHIP_BOOT_MODE_REG value,
move it to SoC's own Kconfig, and add address for rk3128 and
rk3328 so that all SoCs have available address.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: Kconfig: move rk3399 config into its Kconfig

Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: Kconfig: move rk3368 config into its Kconfig

Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: Kconfig: move rk3288 config into its Kconfig

Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: Kconfig: move rk322x config into its Kconfig

Each SoC have its config setting and its Kconfig, move
the specific setting to its own Kconfig file.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: fixup board choice in Kconfig

Kconfig for board target select is choice option, fixup for
rk3036, rk3288 and rv1108.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: remove redundant pinctrl header including

No code is using this header file, remove it.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3288: remove pinctrl init in spl_board_init

The pinctrl will default init the io while driver is probe
with new pinctrl driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3188: remove pinctrl init in spl_board_init

The pinctrl will default init the io while driver is probe
with new pinctrl driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: rk3399: remove pinctrl init in spl_board_init

The pinctrl will default init the io while driver is probe
with new pinctrl driver.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

rockchip: dts: rk3399: rock-pi-4: Use LPDDR4-100 dtsi

Use LPDDR4-100 sdram timings dtsi for RockPI-4 board.

All these timings are processed during TPL stage of rock-pi-4 board,
bootchain. This make TPL would replace rockchip in house rkbin in
current bootchain.

Bootchain after and before this change:

   TPL -> SPL -> U-Boot proper

 rkbin -> SPL -> U-Boot proper

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

rockchip: dts: rk3399: nanopi-neo4: Use DDR3-1866 dtsi

Use DDR3-1866 2GB ddr timings dtsi for 1GB NanoPi Neo4 board.

Since sdram rk3399 support dynamic stride and rank detection it
can able to detect 1GB ddr eventough the timings are meant for
dual channel, 2GB size.

Bootchain after and before this change are:

 TPL -> SPL -> U-Boot proper

 rkbin -> SPL -> U-Boot proper

This certainly fix the second channel data training initialization
since we have dynamic rank, stride where second channel capabilities
are clear or memset to 0.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

rockchip: dts: rk3399: rockpro64: Use LPDDR4-100 dtsi

Use LPDDR4-100 sdram timings dtsi for Rockpro64 board.

All these timings are processed during TPL stage of rockpro64 board,
bootchain. This make TPL would replace rockchip in house rkbin in
current bootchain.

Bootchain after and before this change:

   TPL -> SPL -> U-Boot proper

 rkbin -> SPL -> U-Boot proper

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

rockchip: dts: rk3399: Add LPDDR4-100 timings

Add sdram timings for LPDDR4-100 via rk3399-sdram-lpddr4-100.dtsi file.
all timings are dumped from rkbin/bin/rk33/rk3399_ddr_800MHz_v1.20.bin

Associated LPDDR4 board -u-boot.dtsi can include this to make these
timings available during SPL or TPL stages.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

configs: rock-pi-4: Enable LPDDR4 support

Due to foot-print issues, we have LPDDR4 code can be
marked as CONFIG_RAM_RK3399_LPDDR4.

So, enable it for Rock-PI-4 board.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

configs: rockpro64: Enable LPDDR4 support

Due to foot-print issues, we have LPDDR4 code can be
marked as CONFIG_RAM_RK3399_LPDDR4.

So, enable it for Rockpro64 board.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add lpddr4 set rate support

Unlike rest of dram type chips, LPDDR4 initialization start
with at board selected frequency (say 50MHz) and then it
switches into 400MHz and 800MHz simultaneously to make the
proper sequence work on each channel with associated training.

The lpddr4 set rate sequnce will follow by setting lpddr4
- dq out
- ca odt
- MR3
- MR12
- MR14
registers sets in sequential order.

Here is sameple log about LPDDR4-100 init sequence in Rockpro64:

Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
channel 0 training pass
channel 1 training pass
change freq to 400 MHz 0, 1
channel 0 training pass
channel 1 training pass
change freq to 800 MHz 1, 0

This patch add support to this init sequence via lpddr4 set rate
by taking sdram timing parameters from 400, 800 .inc files.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
(Fix travis error, use one ret instead of ret[2] in set_ctrl)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

ram: rk3399: Add set_rate sdram rk3399 ops

DDR set rate can be even required for lpddr4 and we
need to keep the lpddr4 code to compile only for relevant
boards which do support lpddr4.

For this requirement, and for code readability handle
data training via sdram_rk3399_ops with .set_rate and
same will update in future while supporting lpddr4 code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add LPPDDR4-800 timings inc

LPDDR4 initialization start with at board selected frequency
and then it switches into 400MHz and 800MHz simultaneously to
make the proper sequence work on each channel with associated
training.

So, add LPDDR4-800 timings inc file in driver area so-that
these timings will take during LPDDR4 initialization phase.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add LPPDDR4-400 timings inc

LPDDR4 initialization start with at board selected frequency
and then it switches into 400MHz and 800MHz simultaneously to
make the proper sequence work on each channel with associated
training.

So, add LPDDR4-400 timings inc file in driver area so-that
these timings will take during LPDDR4 initialization phase.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

clk: rockchip: rk3399: Set 400MHz ddr clock

Add support for setting 400MHz ddr clock.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

clk: rockchip: rk3399: Set 50MHz ddr clock

Add support for setting 50MHz ddr clock.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

rockchip: dts: rk3399: Add u-boot, dm-pre-reloc for pmu

Add u-boot,dm-pre-reloc property for pmu in rk3399-u-boot.dtsi
so-that SPL can access pmu.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

rockchip: rk3399: syscon: Add pmu support

Add pmu compatible with relevant U_BOOT_DRIVER for rk3399
via syscon rk3399 driver.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

arm: include: rockchip: Add rk3399 pmu file

Add pmu header file for rk3399 SoC, this will help
to configure pmu in sdram driver.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add LPPDR4 mr detection

Like data training in other sdram types, mr detection need
to taken care for lpddr4 with looped rank and associated
channel to make sure the proper configuration held.

Once the mr detection successful for active and configured
rank with channel number, the same can later reused during
actual LPDDR4 initialization.

So, add code to support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Handle data training via ops

data training can be even required for lpddr4 and we
need to keep the lpddr4 code to compile only for relevant
boards which do support lpddr4.

For this requirement, and for code readability handle
data training via sdram_rk3399_ops and same will update
in future while supporting lpddr4 code.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Simplify data training first argument

data training is using chan_info as first argument with
channel number as second argument instead of that use
dram_info as first argument so-that we can get the
chan_info at data training definition.

This was the argument handling is meaningful, readable
and it would help to add similar data training for
lpddr4 in future.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Update lpddr4 vref_mode_ac

Update vref_mode_ac for lpddr4 based on VDDQ/3/2=16.8%

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Update lpddr4 mode_sel based on io settings

The mode_sel on lpddr4 value is depending on IO settings
of rd_vref.

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>

ram: rk3399: Update lpddr4 vref based on io settings

The vref_mode_dq, vref_value_dq on lpddr4 value is depending
on IO settings of rd_vref.

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Get lpddr4 tsel_rd_en from io settings

For base.odt 1 the lpddr4 tsel_rd_en value is depending
on IO settings of rd_odt_en.

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Configure soc odt support

CTL 145, 146, 159, 160 registers are used to configure
soc odt on rk3399.

These soc odt values are updated from CS0_MR22_VAL and
CS1_MR22_VAL and for lpddr4 these values ORed with
tsel_rd_select_n.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>

ram: rk3399: Add tsel control clock drive

tsel contrl clock drives are required to configure PHY
929, 939 controls drive settings.

Add support for these control clock for all dramtype
sdrams.

Thse control clock drives are configure via tsel_ckcs_select_p
and tsel_ckcs_select_n variables.

tsel_ckcs_select_n is PHY_DRV_ODT_34_3 value where as
tsel_ckcs_select_p is retrived from IO settings for lpddr4
and rest uses PHY_DRV_ODT_34_3.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: sdram: Configure lpddr4 tsel rd, wr based on IO settings

Now we have IO settings available for all supported sdram
frequencies, so retrieve these IO settings and make used
for LPDDR4 ds odt configuration.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>

ram: rk3399: Add IO settings

Add IO settings for dram ctl and phy.

IO settings are useful for configuring ctl, phy odt, vref,
mr5, mode select and other needed input output operations
for lpddr4 or any other dramtype sdram.

Right now, this patch added IO setting for all supported
sdram frequencies.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Don't disable dfi dram clk for lpddr4, rank 1

The hardware for LPDDR4 with
- CLK0P/N connect to lower 16-bits
- CLK1P/N connect to higher 16-bits

and usually dfi dram clk is configured via CLK1P/N, so
disabling dfi dram clk will disable the CLK1P/N as well.

So, add patch to not to disable dfi dram clk for lpddr4,
with rank 1.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Configure tsel write ca for lpddr4

tsel write ca_p and ca_n values need to write on PHY 544, 672
and 800 to configure ds odt.

Configure the same PHY register for lpddr4 would require a mask
value of (300 << 8).

Add support for it.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Map chipselect for lpddr4

Assign desired cs_map values for lpddr4 during set memory map.

Initial cs_map values is based on the sdram parameters, so
the same will adjusted based dramtype as LPDDR4.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>

ram: rk3399: Configure PHY RX_CM_INPUT for lpddr4

Configure PHY RX_CM_INPUT for lpddr4 during phy IO config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Configure SLEWP_EN, SLEWN_EN for lpddr4

Configure SLEWP_EN, SLEWN_EN for lpddr4 during phy IO config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>

ram: rk3399: Configure BOOSTP_EN, BOOSTN_EN for lpddr4

Configure BOOSTP_EN, BOOSTN_EN for lpddr4 during phy IO config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Configure PHY_898, PHY_919 for lpddr4

PHY_898, PHY_919 would require to configure PHY LP4 boot
pll control and ca for lpddr4.

So, configure the same in pctl_cfg for LPDDR4.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Avoid two channel ZQ Cal Start at the same time

It is possible in lpddr4 dram, where both the channels would
start at same time with ZQ Cal Start. If it uses ZQ Call start
then it will use RZQ.

For example LPDDR4 366 Dual-Die, Quad-Channel Package, RZQ maybe
connect to both channel. If ZQ Cal Start at the same time,
it will use the same RZQ.

It is not a problem of using RZQ in both the channels, but can not
use at the same time.

So, to avoid this, we have an option of dram tINIT3 value for
increasing the frequency for channel 1.

This patch increase the available tINIT3 with existing running
dram frequency.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Don't wait for PLL lock in lpddr4

lpddr4 has PLL bypass mode during phy initialization phase,
which does all pll configurations.

So no need to wait explicitly during pctl config.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Move mode_sel assignment

mode_sel assignment is based on dram type.

In phy_io_config, already have vref setting based
on the dram type, so move this mode_sel assignment
on vref setting area.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add lpddr4 rank mask for wdql training

Add rank_mask based on the rank number for lpddr4.

This would keep the wdql data training loop based on the
desired rank mask value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add lpddr4 rank mask for ca training

Add rank_mask based on the rank number for lpddr4.

This would keep the ca data training loop based on the
desired rank mask value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rockchip: Kconfig: Add RK3399 LPDDR4 entry

Supporting LPDDR4 code support in RK3399 would increases
the size of SPL/TPL.

So add kconfig entry for RK3399 LPDDR4 code so-that
the boards have LPDDR4 can enable them via defconfig.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Configure phy IO in ds odt

Some dramtypes like lpddr4 initialization would required to
configure phy IO even after pctl_cfg and after set_ds_odt.

For those cases the set_ds_odt would be an initial call to
setup the phy.

To satisfy all the cases, trigger phy IO from set_ds_odt.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add DdrMode

Add DdrMode structure with associated bit fields.

These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add ddrtimingC0

Add DdrTimingC0 structure with associated bit fields.

These would help to reconfigure sdram capabilities during
lpddr4 setup related configs.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add ddr version enc macro

Add dram config macro for handling ddr version number.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Introduce sys_reg3 for more capacity info

cs0_row, cs1_row and cs1_col needs more bits to show its
correct value, update to make use of both sys_reg2,
sys_reg3.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash similar patches into one patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Rename sys_reg with sys_reg2

Use dram config variable name as sys_reg2 instead of sys_reg
since the final variable value is to written into a pmugrf
register named as sys_reg2.

This reflect the both variable and associated register
names are same and also help to add next sys_reg's to
add it in future.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Simply existing dram enc macro

Add simplified and meaningful macro for all setting.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(Squash the similar patches into 1 patch)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Enable sdram debug functions

This would help to debug the sdram base parameters while
debugging existing chip or while supporting new sdram type.

It require explicit enablement of CONFIG_RAM_ROCKCHIP_DEBUG
for showing the debug prints.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add rank detection support

Right now the rk3399 sdram driver assume that the board
has configured with 2 channels, so any possibility to
enable single channel on the same driver will encounter
channel #1 data training failure.

Log:
U-Boot TPL board init
sdram_init: data training failed
rk3399_dmc_init DRAM init failed -5

So, add an algorithm that can capable to compute the active
or configured rank with associated channel like
a) do rank loop to compute the active rank, with associated
   channel numbers
b) then, succeed the data training only for configured channel
c) preserve the rank for given channel
d) do channel loop for setting the active channel
e) if given rank is zero or inactive on the specific channel,
   clear the timings for the associated channel
f) finally, return error if number of channels is zero

Tested in NanoPI-NEO4 since it support single channel sdram
configuration.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
(add PI_READ_GATE_TRAINING for LPDDR3 to support rk3399-evb case)
Signed-off-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Compute stride for 1 channel a

Add stride computation for the sdram which support
single channel a

This configuration available in NanoPi NEO4 and the
same can work with existing rk3399-sdram-ddr3-1866.dtsi

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Compute stride for 2 channels

stride value from sdram timings can be computed dynamically
based on the determined capacity for the given channel.

Right now these stride values are taken as part of sdram timings
via dtsi, but it possible to use same timings dtsi for given
frequency even though the configured board sdram do support
single channel with different size by dynamically detect the
stride value.

Example, NanoPi NEO4 do have DDR3-1866, but with single channel
and 1GB size with dynamic stride detection it is possible to
use existing rk3399-sdram-ddr3-1866.dtsi whose stride,
number of channels and capacity it support is d efferent.

So, add initial support to calculate the stride value for
2 channels sdram, which is available by default on existing
boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: debug: Add sdram_print_stride

Add code to print the channel stride, this would help to
print the stride of associated channel.

Here is sample print on LPDDR4, 50MHz.
256B stride

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rockchip: debug: Get the cs capacity

Add code to get the channel capacity, this would help to
print the capacity of specific channel.

Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rockchip: debug: Add sdram_print_ddr_info

Add sdram ddr info print support, this would help to
observe the sdram base parameters.

Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rockchip: Add debug sdram driver

Add sdram driver to handle debug across rockchip SoCs.

This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

debug_uart: Add printdec

Add printdec, this would help to print an
output a decimalism value.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rockchip: Add initial Kconfig

Right now sdram drivers in rockchip SoC are built based
on the SoC configs which may not be an adequate solutions
while adding common or debug driver.

So, add meaningful Kconfig options start with rk3399.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add pctl start support

Add support for pctl start for both channel 0, 1 control
and phy registers.

This would also handle pwrup_srefresh_exit init based
on the channel number.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Move pwrup_srefresh_exit to dram_info

Add pwrup_srefresh_exit to be part of dram_info so-that
the it can help to support pwrup_srefresh_exit in individual
channels while starting pctl in future.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Add phy pctrl reset support

Add support for phy pctrl reset support for both channel 0, 1.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Use rank mask in wdql data training

Add rank_mask based on the rank number, this would keep
the wdql data training loop based on the desired rank mask
value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Use rank mask in ca data training

Add rank_mask based on the rank number, this would keep
the ca data training loop based on the desired rank mask
value instead of looping for all values.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Clear PI_175 interrupts in data training

Clear the PI_175 interrupts before processing actual
data training in all relevant calls.

This would help to clear interrupt from previous training.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Handle data training return types

data trainings calls like ca, wl, rg, rl, wdql have proper
return types with -EIO and the return type missed to handle
in data_training function.

This patch, add proper return type checks along with useful
debug statement on each data training calls.

Incidentally this would help to prevent the sdram initialization
hang for single channel dram and when the code is trying to
initialize second channel with proper return type of relevant
data training call might failed.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

clk: rockchip: rk3399: Fix check patch warnings and checks

- CHECK: spaces preferred around that '*'
- CHECK: spaces preferred around that '/'
- CHECK: space preferred before that '|'
- WARNING: macros should not use a trailing semicolon
- CHECK: Unnecessary parentheses around 'fbdiv <= min_fbdiv'
- CHECK: Unnecessary parentheses around 'parent->id == SCLK_MAC'
- CHECK: Unnecessary parentheses around 'parent->dev == clk->dev'
- WARNING: line over 80 characters
- CHECK: Prefer kernel type 'u8' over 'uint8_t'
- Add proper macro definitions arrangements

Note: there are still line over 80 characters and other warnings but
fixing those making code look unreadable, so I kept it as it is.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

arm: include: rockchip: Add DDR4 enum

Add DDR4 enum number in common header.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

arm: include: rockchip: Move dramtypes to common header

dramtype enum numbers as common across all dram controllers
in rockchip, so move the eneum values in common header.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Move common sdram structures in common header

Move common sdram structures like sdram_cap_info, sdram_base_params
into sdram_common header, this would help to reuse the same
from another controllers like px30.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: s/rk3399_base_params/sdram_base_params

Most of the ddr parameters are common in rk3399_base_params
structure and which would reuse it in another controller like
px30 in future.

So, rename the structure from rk3399_base_params into
sdram_base_params.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rockchip: rk3399: Add cap_info structure

Group common ddr attributes like
- rank
- col
- bk
- bw
- dbw
- row_3_4
- cs0_row
- cs1_row
- ddrconfig

into a common cap_info structure for more code readability and extend
if possible based on the new features.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: Order tsel variables

Order tsel* variable declarations and assignment in proper
and meaningful way.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: s/ca_tsel_wr_select_p/tsel_wr_select_ca_p

Rename ca_tsel_wr_select_p to tsel_wr_select_ca_p based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: s/ca_tsel_wr_select_n/tsel_wr_select_ca_n

Rename ca_tsel_wr_select_n to tsel_wr_select_ca_n based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>

ram: rk3399: s/tsel_wr_select_p/tsel_wr_select_dq_p

Rename tsel_wr_select_p to tsel_wr_select_dq_p based
on the bsp code.

No functionality change.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>