Yong Qin [Mon, 12 Nov 2018 09:39:29 +0000 (17:39 +0800)]
hdmirx: tl1 hdmirx no interrupt [1/1]
PD#172587
Problem:
1.no interrupt
2.add fsm debug log
Solution:
1.change interrupt id
2.change interrupt source
3.change 6g phy setting
4.add axi clk
5.verify emp pkt data to ddr
Verify:
1.verify on chip
Change-Id: I349439d90a356144b96af4831e03fa0e9e90076b
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Yong Qin [Mon, 12 Nov 2018 07:45:46 +0000 (15:45 +0800)]
hdmirx: modify audio pll setting [1/1]
PD#172587
Problem:
1.audio divider it's not work
Solution:
1.modify audio top clk measure
2.modify audio divider clk source
3.modify audio divider band gap
Verify:
tl1
Change-Id: Iea254f043531f31383a727c58b4d992dd39ff2ce
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Yong Qin [Mon, 12 Nov 2018 03:38:33 +0000 (11:38 +0800)]
cec: add device match for tl1 [1/1]
PD#172587
Problem:
add device match for tl1
Solution:
1.add cecb ver
2.add ceca status reg flag
Verify:
1.run TPM
2.run chip
Change-Id: I304abfd1d6f1f216f9f0c56ca19a8bdb2ccfeabb
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Yong Qin [Mon, 12 Nov 2018 02:04:37 +0000 (10:04 +0800)]
hdmirx: fix phy init err and add debug [1/1]
PD#172587
Problem:
1.cable clk is not match from clk measure
2.add some debug interface for tl1
Solution:
1.add audio clock source from tmds
2.add audio clock source from mpll
3.low FRQ phy audio clock out is 4xtmds clk
4.add 6G phy setting
5.match clock measure return value hz
6.phy initial enable terminal by input source
7.add channel switch control 0/1
8.last line,mode:4k2k 420 deep color problem
9.dump register, add error cnt for tl1
10.capture emp data into a file
11.modify tmds data align, snps phy disable
Verify:
1.run ptm
2.verify on chip
Change-Id: I9d003748c0df3dfbd25f7ab987449e2097251c58
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
Nian Jing [Mon, 19 Nov 2018 14:11:50 +0000 (22:11 +0800)]
cvbs: cvbsoutput support for tl1 [1/1]
PD#172587
Problem:
no cvbsoutput
Solution:
add cvbsoutput
Verify:
test pass on x301
Change-Id: I92f70d26e32f95de7c63ddbac9fe6664063c1902
Signed-off-by: Nian Jing <nian.jing@amlogic.com>
Brian Zhu [Thu, 15 Nov 2018 16:38:41 +0000 (00:38 +0800)]
video: vpp: add vd afbc YUV 422/444 support for tl1 [1/1]
PD#172587
Problem:
Bringup TL1 vidoe driver.
TL1 need support YUV422/444 AFBC.
TL1 need check afbc source from decode or vdin.
TL1 need afbc compress loss mode.
Solution:
Merge from branch bringup/amlogic-4.9/tl1-
20181111.
Verify:
verify on tl1
Change-Id: I0af62e7638db4e1c349df874ccffdeddcaa715af
Signed-off-by: Brian Zhu <brian.zhu@amlogic.com>
Jian Cao [Thu, 15 Nov 2018 09:37:14 +0000 (17:37 +0800)]
osd: osd: screen blank when boot [1/1]
PD#172587
Problem:
screen blank when boot
Solution:
modify free_scale_switch
Verify:
verified on tl1 dev board
Change-Id: I3c53e832c83c71bd8e98f71fcd654865a467df3c
Signed-off-by: Jian Cao <jian.cao@amlogic.com>
Jian Cao [Tue, 20 Nov 2018 02:30:25 +0000 (10:30 +0800)]
osd: osd: reserve vs_ctrl bit for VPP [1/1]
PD#172587
Problem:
reserve vs_ctrl bit for VPP
Solution:
Avoid operating VPP_OFIFO_SIZE bit19 on OSD code
Verify:
verified on t962x2_x301
Change-Id: Ic450d6f64e2349d97d02f0802058b4031564fea4
Signed-off-by: Jian Cao <jian.cao@amlogic.com>
pengcheng chen [Tue, 20 Nov 2018 01:42:44 +0000 (09:42 +0800)]
osd: add viu2 support for tl1 [1/1]
PD#172587
Problem:
add viu2 support for tl1.
Solution:
add viu2 support for tl1.
Verify:
verified by x301
Change-Id: Ie728f6ee7e0c4c4062e5e12e3d80515d99d020f8
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
pengcheng chen [Thu, 15 Nov 2018 02:04:13 +0000 (10:04 +0800)]
osd: tl1 hold line fix needn't shift workaround [1/1]
PD#172587
Problem:
tl1 hold line fix needn't shift workaround.
Solution:
remove shift workaround int tl1
Verify:
verified by x301
Change-Id: I96d99758ba6f93622c34a8e69c4a3f769fdfad49
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
wenfeng.guo [Mon, 12 Nov 2018 02:54:08 +0000 (10:54 +0800)]
deinterlace: add support for tl1 [1/1]
PD#172587
Problem:
bringup tl1
Solution:
add deinterlace driver support for tl1
Verify:
verified on tl1 x301
Change-Id: I3bf008a4f948cdc2c11f14f81944695d6a185b14
Signed-off-by: wenfeng.guo <wenfeng.guo@amlogic.com>
Zhiwei Yuan [Fri, 23 Nov 2018 14:33:36 +0000 (22:33 +0800)]
dtv_demod: add DTV demod driver for tl1 [1/1]
PD#172587
Problem:
add DTV demod driver for tl1
Solution:
add DTV demod driver for tl1
Verify:
verified by t962x2_x301
Change-Id: I27e88090aa51c0385867cee4d31a5a75192cf650
Signed-off-by: Zhiwei Yuan <zhiwei.yuan@amlogic.com>
Nian Jing [Fri, 23 Nov 2018 12:34:03 +0000 (20:34 +0800)]
tvafe: add tvafe support for tl1 [1/1]
PD#172587
Problem:
tl1 do not support tvafe
Solution:
add tvafe support
Verify:
test pass on x301
Change-Id: I34185a3f10e7540b7c2317c270a306b8904e0ca3
Signed-off-by: Nian Jing <nian.jing@amlogic.com>
ruixuan.li [Wed, 14 Nov 2018 02:14:27 +0000 (10:14 +0800)]
arm: dts: tl1: update emmc dt for tl1 [1/1]
PD#165583
Problem:
bringup tl1 emmc
Solution:
1.set DDR52 MODE
2.add sdio node in dts
3.hs200 busmod
Verify:
test pass on tl1
Change-Id: I5b5c8bff18093f444e67b8e32e2a46c25ddf1a10
Signed-off-by: ruixuan.li <ruixuan.li@amlogic.com>
Bencheng Jing [Thu, 22 Nov 2018 07:48:53 +0000 (15:48 +0800)]
amvecm: pq: lc: update local contrast setting [1/1]
PD#172587
Problem:
update lc setting
Solution:
update lc setting
add demo mode
Verify:
verified on ref board x301
Change-Id: Ie1542af5e4d8e4fe2c52bd04db66cbdf9130853f
Signed-off-by: Bencheng Jing <bencheng.jing@amlogic.com>
nengwen.chen [Fri, 23 Nov 2018 09:11:25 +0000 (17:11 +0800)]
atv_demod: add atv demod support for tl1 [1/1]
PD#172587
Problem:
1.add atv demod driver and dts config for tl1.
2.merge from bringup/amlogic-4.9/tl1-
20181111.
Solution:
add atv demod driver and dts config for tl1
Verify:
verified by t962x2_x301
Change-Id: Ibbc00f9d478a9f5e52c6333b9a819aac381894ec
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Xing Wang [Tue, 30 Oct 2018 07:38:34 +0000 (15:38 +0800)]
audio: auge: fix drivers for tl1 [1/1]
PD#172587
Problem:
resample, eqdrc, dolby efuse, audio input (from atv, hdmirx)
Solution:
add drivers for them
Verify:
x301
Change-Id: I5187f9824d904283794f6e4be3dd9ce8463908e1
Signed-off-by: Xing Wang <xing.wang@amlogic.com>
Ruixuan Li [Mon, 26 Nov 2018 12:53:39 +0000 (20:53 +0800)]
emmc: modify cophase for tl1 [1/1]
PD#172587
Problem:
emmc data crc error
Solution:
modify cophase under kernel for tl1
Verify:
test pass on skt
Change-Id: Id4997ef2288a53e6f401744664aaf6b05cf36e38
Signed-off-by: Ruixuan Li <ruixuan.li@amlogic.com>
Sunny Luo [Mon, 15 Oct 2018 08:09:03 +0000 (16:09 +0800)]
spicc: fix miss bytes/time consume/loopback issue [1/1]
PD#SWPL-215
Problem:
1. additional or missing bytes be sent on mosi sometimes.
2. Customer DSP load firmware through SPICC. the loading time is 12s with
buildroot release
20180907 while 6s with
20180131.
3. rx error when work in loopback mode at high speed.
Solution:
1. change to disable irq at the irq-handle begining;
change to enable irq after all data pulled.
2. pre-setup of every spi transfer spends most of time on clk_set_rate().
this time is not obvious while cpu work at a high frequence such as
1000MHz.
In fact, a slave speed is almost fixed and we needn't set it for every
transfer but set only when speed changed.
3. disable auto io delay when in loopback mode.
Verify:
verified on axg-s400-v03 and tl1-skt
Change-Id: I61bcceccc243b218879b2b0711d0aff7538151f6
Signed-off-by: Sunny Luo <sunny.luo@amlogic.com>
Yue Wang [Sun, 11 Nov 2018 09:23:31 +0000 (17:23 +0800)]
usb: bringup usb for tl1 [1/1]
PD#172587
Problem:
bringup usb for tl1
Solution:
bringup usb for tl1.
disable usb device sof interrupt for tl1.
Verify:
verify on tl1 skt.
Change-Id: Ifbcd3b406145ac39709ff2df795544086277f00e
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Zhongfu Luo [Tue, 20 Nov 2018 02:58:48 +0000 (10:58 +0800)]
efuse: tl1: add efuse burning support [1/1]
PD#172587
Problem:
efuse: tl1: need to add efuse burning support
Solution:
efuse: tl1: add efuse burning support
Verify:
TL1 skt board verify pass
Change-Id: Id65f182c71fc6f3f2b2536bbb6b859ad2f558360
Signed-off-by: Zhongfu Luo <zhongfu.luo@amlogic.com>
Bichao Zheng [Thu, 15 Nov 2018 06:01:55 +0000 (14:01 +0800)]
irblaster: meson: add support for tl1 [1/1]
PD#172587
Problem:
1.Bringup TL1.
2.Invalid frequency setting
Solution:
1.Add ir blaster device tree for tl1.
2.Add frequency setting
Verify:
verify on tl1.
Change-Id: I51759e32577172ff766fd4d50f92a00ef77c7495
Signed-off-by: Bichao Zheng <bichao.zheng@amlogic.com>
Xingyu Chen [Mon, 12 Nov 2018 12:57:48 +0000 (20:57 +0800)]
pinctrl: meson: update pin groups for tl1 [1/1]
PD#172587
Problem:
some pin groups are not supported
Solution:
update pin groups according to pinmux document v8.
Verify:
TL1 skt board.
Change-Id: I88750e307208fd30c20343c1c5418c1035961b4e
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Jian Hu [Thu, 8 Nov 2018 06:32:27 +0000 (14:32 +0800)]
clk: tl1: bringup clock for tl1 [1/1]
PD#172587
Problem:
Bringup clock for tl1.
Solution:
Bringuup clock for tl1.
Cherrypick from bringup/amlogic-4.9/tl1-
20181111
1. Add hdmirx meter clock
2. fix gp0 pll error
3. remove vpu_clk enable in clktree
4. add hdmi axi clock
5. fix tl1 mpll clk overflow issue
6. fix vapb clock error rate
7. add 1.404G and 1.5G cpu freqs for tl1
Verify:
TL1 T962X2 X301 & SKT
Change-Id: I73a9afca35f8a9ce26cc6f3a75a738525fc8d728
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Xingyu Chen [Sun, 11 Nov 2018 07:05:34 +0000 (15:05 +0800)]
arm: dts: tl1: add device tree for skt and x301 boards [1/1]
PD#172587
Problem:
Bringup tl1 skt & x301.
Solution:
Add device tree for skt and x301 boards.
Verify:
test pass on skt board
Change-Id: Ia6c16be242b5cc430a38ec6b9cac8c320f7339d7
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Bo Yang <bo.yang@amlogic.com>
sky zhou [Sat, 24 Nov 2018 13:56:30 +0000 (21:56 +0800)]
framebuffer: remove lock in fbmem ioctl. [1/1]
PD#SWPL-2497
Problem:
on 32bit kernel, when user space call WAITFORVSYNC,
we cannot send other command to framebuffer.
Solution:
remove lock in fbioctl as fb compat_ioctl do.
Our driver have locks to protect internal resources.
Verify:
verified on franklin.
Change-Id: I1789c09a7ea459aed4b782748847687c7f974526
Signed-off-by: sky zhou <sky.zhou@amlogic.com>
Yi Zhou [Fri, 23 Nov 2018 06:37:32 +0000 (14:37 +0800)]
dv: fix osd color matrix when dv enabled [1/1]
PD#SWPL-1804
Problem:
fix osd color matrix when dv enabled
Solution:
enable osd matrix when dv enabled
Verify:
verified on u212 dev board
Change-Id: I4b4206f4d8c447873f23a3a0066af0d0fa85e18c
Signed-off-by: Yi Zhou <yi.zhou@amlogic.com>
pengcheng chen [Thu, 22 Nov 2018 04:54:06 +0000 (12:54 +0800)]
osd: fix osd color error when osd hdr enabled [1/1]
PD#SWPL-1804
Problem:
osd color error when osd hdr enabled
Solution:
div alpha when osd hdr enabled
Verify:
verified on u212 dev board
Change-Id: I1f5ea0db404d1956f454bd5da2532bded89626ee
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
pengcheng chen [Tue, 30 Oct 2018 06:55:40 +0000 (14:55 +0800)]
osd: add meson-hwc repodution rate support [1/2]
PD#SWPL-1810
Problem:
osd blend repodution rate not supported
Solution:
add meson-hwc repodution rate support
Verify:
verified on u212 dev board
Change-Id: Ied10393e240e8d3f2a1eefe17a2d4d3c965e3383
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
Zhongfu Luo [Fri, 23 Nov 2018 03:34:33 +0000 (11:34 +0800)]
dts: TXL: defendkey: support secure upgrade check [1/1]
PD#SWPL-2343
Problem:
TXL need to support secure upgrade check
Solution:
add defendkey support in all TXL dts
Verify:
TXL skt board verify pass
Change-Id: Idb81fa1f1b5a27e5c44dc961ceef94f1edfc06d9
Signed-off-by: Zhongfu Luo <zhongfu.luo@amlogic.com>
Hang Cheng [Wed, 14 Nov 2018 08:30:17 +0000 (16:30 +0800)]
hdmirx: optimize for audio fifo [1/1]
PD#SWPL-2114
Problem:
When change audio channel count on VG-877, the subpkts of skipped
middle channels are still carried, thus causing afifo overflow
Solution:
When afifo overflow, then store all audio subpkts(8ch)
into afifo, and output 8ch audio from afifo
Verify:
R321
Change-Id: I4b0933935d3a1aed20be10a7a8d3fe23c3a39323
Signed-off-by: Hang Cheng <hang.cheng@amlogic.com>
Zhongfu Luo [Thu, 22 Nov 2018 06:12:59 +0000 (14:12 +0800)]
dts: GXL: defendkey: support secure upgrade check [3/3]
PD#SWPL-2100
Problem:
GXL need to support secure upgrade check
Solution:
add defendkey support in all GXL dts
Verify:
GXL skt board verify pass
Change-Id: I73b84b86f23f512ddc556b61f3a07d015c717e8c
Signed-off-by: Zhongfu Luo <zhongfu.luo@amlogic.com>
Zhongfu Luo [Wed, 21 Nov 2018 10:14:23 +0000 (18:14 +0800)]
GXL: defendkey: support secure upgrade check [2/3]
PD#SWPL-2100
Problem:
GXL need to support secure upgrade check
Solution:
1.add dtb decrypt support
2.add 32bit defendkey support
Verify:
GXL skt board verify pass
Change-Id: I501967530b2a61d9b90c20241b82f92b00829453
Signed-off-by: Zhongfu Luo <zhongfu.luo@amlogic.com>
Hong Guo [Fri, 23 Nov 2018 02:34:07 +0000 (10:34 +0800)]
PM_SUSPEND: suspend: set wakeup reason to stick mem [2/2]
PD#SWPL-2287
Problem:
set wakeup reason to stick mem
Solution:
set wakeup reason to stick mem
Verify:
gxl,test pass
Change-Id: Iff6f1824ea4ac9ec12b8295d4283992fdac03b14
Signed-off-by: Hong Guo <hong.guo@amlogic.com>
Jianxin Pan [Mon, 26 Nov 2018 03:25:05 +0000 (19:25 -0800)]
Merge "deinterface: temporary remove afbc support on chip after g12a [1/1]" into amlogic-4.9-dev
Hanjie Lin [Thu, 22 Nov 2018 07:50:33 +0000 (15:50 +0800)]
dts: aarch32: modify timer for aarch32 [1/1]
PD#SWPL-2383
Problem:
32bit_kernel VtsKernelLinuxKselftest module 1 fail
Solution:
modify timer for aarch32
Verify:
p321
Change-Id: I9ef79e927f3244223dbbb57bcc6155c1ffc8989c
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
wenfeng.guo [Tue, 20 Nov 2018 11:38:43 +0000 (19:38 +0800)]
deinterlace: fix CMA layout adaptation di_cma_reserved [1/1]
PD#SWPL-2308
Problem:
CMA layout adaptation di_cma_reserved cause crash
Solution:
fix CMA layout adaptation di_cma_reserved
Verify:
P321
Change-Id: Ia24e811a02d47d70afa1c06361fd0852c357394c
Signed-off-by: wenfeng.guo <wenfeng.guo@amlogic.com>
Jianxiong Pan [Fri, 23 Nov 2018 16:39:06 +0000 (00:39 +0800)]
Revert "arm: dts: tl1: add tl1 device tree fils [1/1]"
This reverts commit
32cfa235e3c9b543c396083068d107a800a93fdb.
Change-Id: I23d0e860bd858e1a9982151977524b178524842a
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
huaihao.guo [Fri, 23 Nov 2018 02:31:02 +0000 (10:31 +0800)]
deinterface: temporary remove afbc support on chip after g12a [1/1]
PD#172587
Problem:
afbc now support on chip txlx and g12a,
but we use cpu_after_eq(G12A) to judge
if afbc is support or not.
Solution:
use is_meson_g12a_cpu() replace cpu_after_eq(G12A).
Verify:
u200(g12a),t962x_r311
Change-Id: I3fb7ed54f7137fada97481177e40a2543cf8df9f
Signed-off-by: huaihao guo <huaihao.guo@amlogic.com>
Bo Yang [Fri, 23 Nov 2018 07:35:33 +0000 (15:35 +0800)]
arm: dts: tl1: add tl1 device tree fils [1/1]
PD#172587
Problem:
Bringup TL1 support.
Solution:
Add tl1 device tree files to support tl1 boards.
This device tree files are copied from bringup branch:
bringup/amlogic-4.9/tl1-
20181111
Verify:
The device tree files has been verified on bringup branch:
bringup/amlogic-4.9/tl1-
20181111
Change-Id: Ie85f59a0293319a3511371ab69f3ce07f0fefed3
Signed-off-by: Bo Yang <bo.yang@amlogic.com>
Nian Jing [Fri, 23 Nov 2018 03:05:03 +0000 (11:05 +0800)]
vdac: fix atv/dtv resume no signal issue [1/1]
PD#SWPL-2351
Problem:
atv/dtv no signal when suspend after switch from hdmi
Solution:
disable vdac bandgap when suspend
Verify:
test pass on P321
Change-Id: I0449f0d9673f46928b8951249f5759a4a1f16562
Signed-off-by: Nian Jing <nian.jing@amlogic.com>
MingLiang Dong [Fri, 23 Nov 2018 06:28:11 +0000 (01:28 -0500)]
vpp: fix p212 osd sdr2hdr luma too dark compile [1/1]
PD#SWPL-1707
Problem:
{NTS}Manual,HDR-001-TC2 Failed step 8/12/16/20 VID
and GFX doesn't match
Solution:
add osd hdr2sdr convert table for 400nit on p212
Verify:
verify on p212
Change-Id: I16637652b6d07ba81b25f46c2684ff7ae3e1c68c
Signed-off-by: MingLiang Dong <mingliang.dong@amlogic.com>
MingLiang Dong [Mon, 19 Nov 2018 07:11:28 +0000 (02:11 -0500)]
vpp: fix p212 osd sdr2hdr luma too dark [1/1]
PD#SWPL-1707
Problem:
{NTS}Manual,HDR-001-TC2 Failed step 8/12/16/20 VID
and GFX doesn't match
Solution:
add osd hdr2sdr convert table for 400nit on p212
Verify:
verify on p212
Change-Id: I9a9dcf13ab0deaa8b676c5c409919367420b6d1b
Signed-off-by: MingLiang Dong <mingliang.dong@amlogic.com>
Jianxiong Pan [Fri, 23 Nov 2018 03:28:38 +0000 (11:28 +0800)]
ramdump: fix a warning of cast [1/1]
PD#165764
Problem:
have a warning of the "ram" variable cast.
Solution:
add a "void *" to the ram variable.
Verify:
test locally.
Change-Id: I037a89a28e98ae8c8ab965e908877bf4a72d3ead
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
wenfeng.guo [Wed, 21 Nov 2018 06:29:07 +0000 (14:29 +0800)]
dtv_demod: fix dtv demod crash switch once every 2s [1/1]
PD#SWPL-2293
Problem:
dtv demod switch once every 2s cause crash
Solution:
fix dtv demod crash switch once every 2s
Verify:
P321
Change-Id: Ibfd919a503e3dae41f51637cdff6e01ed27bac71
Signed-off-by: wenfeng.guo <wenfeng.guo@amlogic.com>
live.li [Thu, 22 Nov 2018 02:05:53 +0000 (10:05 +0800)]
avsync: tsync: fix the avsync problem [1/1]
PD#SWPL-1158
Problem:
The video will become un-smooth after change
between several audio languages
Solution:
when apts and vpts distance is large then 60*90000
then set the tsync mode to vmaster and set the tysnc
enable to 0
Verify:
P321
Change-Id: I7c7e32f49ca12645cf6a1aa58caeb968a9234c8c
Signed-off-by: live.li <live.li@amlogic.com>
tao zeng [Thu, 22 Nov 2018 08:01:36 +0000 (16:01 +0800)]
ramdump: add ramdump support for ARM32 [1/1]
PD#165764
Problem:
ramdump is not enabled on ARM32
Solution:
Enable it and fix compatible with ARM64
Verify:
R311
Change-Id: I337ef019ecab05d25b7d9dc0cacab7a03149aa7b
Signed-off-by: tao zeng <tao.zeng@amlogic.com>
MingLiang Dong [Thu, 22 Nov 2018 10:37:45 +0000 (05:37 -0500)]
amvecm: pq: add dnlp/bri/contrast for tl1 [1/1]
PD#172587
Problem:
dnlp/bri/contrast can not finetune
Solution:
1. add dnlp regisiter 10bit write
2. add brightness/contrast/sr for tl1
Verify:
verify on tl1
Change-Id: I90b363f57fbf2cd485e2acaddb5ce60a8715a47b
Signed-off-by: MingLiang Dong <mingliang.dong@amlogic.com>
Wencai You [Tue, 20 Nov 2018 14:12:16 +0000 (22:12 +0800)]
irblaster: add synchronous transmit [1/1]
PD#SWPL-2170
Problem:
cts fail
android.hardware.consumerir.cts.ConsumerIrTest#test_timing
Solution:
add synchronous transmit
when it returns the pattern has been transmitted
Verify:
verify on franklin
Change-Id: I7e490236e5effc13f81e4fab3a1c7fc10c5dcfb3
Signed-off-by: Wencai You <wencai.you@amlogic.com>
Hong Guo [Thu, 22 Nov 2018 03:06:58 +0000 (11:06 +0800)]
vrtc: vrtc time update for stick mem [2/2]
PD#174867
Problem:
vrtc time update for stick mem.
Solution:
vrtc time update for stick mem.
Verify:
g12a txl.
Change-Id: I65074422569370b253882a4e66fb771da10ccdbf
Signed-off-by: Hong Guo <hong.guo@amlogic.com>
guotai.shen [Fri, 16 Nov 2018 06:15:25 +0000 (14:15 +0800)]
dts: r314: increase board dts file [2/3]
PD#SWPL-1978
Problem:
bring up board r314.
Solution:
increase board dts file
feature:
The Dts file with Einstein is identical except for the memory difference
R314 1.5G, Einstein 1G.
Verify:
Verified on txlx_t962x_r314 board.
Change-Id: I271cb92a9cbcab174fb0bb76cfbc8beff9c730d3
Signed-off-by: guotai.shen <guotai.shen@amlogic.com>
Nanxin Qin [Wed, 21 Nov 2018 03:36:37 +0000 (11:36 +0800)]
dts: the memory of the reserved 1MB was recovered. [1/1]
PD#SWPL-2250
Problem:
h265 & vp9 4K playback abnormal because HEVC FRONT &
VPU READ2 pollute the phy address of near 0x0.
Solution:
it's only a temporary modification, the real reason
needs to take more time fixed.
Verify:
U212
Change-Id: I3dcc47f8979960e95c89cf53fe10eadc1a7ae5ad
Signed-off-by: Nanxin Qin <nanxin.qin@amlogic.com>
Renjiang Han [Thu, 8 Nov 2018 06:45:50 +0000 (14:45 +0800)]
ionvideo: Add thread stop protection when the process exits [1/1]
PD#SWPL-1689
Problem:
The thread still exists when the process exits
Solution:
Check if the thread exits when the process exits
Verify:
local
Change-Id: I6d805da6bfa0df85b6d39d065c95eed49b3cb7da
Signed-off-by: Renjiang Han <renjiang.han@amlogic.com>
Yonghui Yu [Thu, 8 Nov 2018 09:30:39 +0000 (17:30 +0800)]
mmc: fixup toshiba emmc secure discard [1/1]
PD#SWPL-1937
Problem:
secure discard and trim may cost 5mins on toshiba
"004GA0" emmc.
Solution:
using normal discard operation instead.
Verify:
W400
Change-Id: I7fd23867f8ae0af9192377de8f8c15609ef809ed
Signed-off-by: Yonghui Yu <yonghui.yu@amlogic.com>
Jihong Sui [Fri, 21 Sep 2018 02:03:15 +0000 (10:03 +0800)]
deinterlace: fix kasan bug in di_task_handle [1/1]
PD#173820
Problem:
kasan bug in di_task_handle
Solution:
delete cma_mutex because it has no effect
Verify:
P321
Change-Id: Ie6ca7973576e7350870c5466b54b38b490dff65e
Signed-off-by: Jihong Sui <jihong.sui@amlogic.com>
tao zeng [Wed, 21 Nov 2018 01:13:48 +0000 (09:13 +0800)]
ddr: fix dmc_monitor register bit missmatch on G12A/G12B [1/1]
PD#172256
Problem:
On G12A/G12B, bit for ddr0 protection 0 vilation is not same
Solution:
Fix bit missmatch problem
Verify:
U212
Change-Id: I5dca14c8bc96bdcb85dbe8bbd5a9a18157834bcf
Signed-off-by: tao zeng <tao.zeng@amlogic.com>
Zongdong Jiao [Thu, 1 Nov 2018 08:29:04 +0000 (16:29 +0800)]
hdmitx: fix wrong power uevent in suspend/resume [1/1]
PD#SWPL-1931
Problem:
Wrong hdmi_power uevent in suspend/resume flow
Solution:
Remove current mode judgement
Verify:
R321
Change-Id: Ib36e8d6cb4988f7b2be91146b12e974c194526ca
Signed-off-by: Zongdong Jiao <zongdong.jiao@amlogic.com>
Evoke Zhang [Fri, 2 Nov 2018 06:22:41 +0000 (14:22 +0800)]
backlight: ldim: update usage for new spi driver [1/1]
PD#SWPL-1603
Problem:
don't support old spi driver now
Solution:
update new spi driver api for ldim driver
Verify:
txlx r311
Change-Id: I4dff13e4cab5666a30488730e27c6275b933a922
Signed-off-by: Evoke Zhang <evoke.zhang@amlogic.com>
Xindong Xu [Fri, 26 Oct 2018 06:29:30 +0000 (14:29 +0800)]
dts: dtsi: add dtsi for ab update [1/6]
PD#SWPL-1513
Problem:
ab update can not work on P
Solution:
add dtsi for ab update for P
Verify:
test pass in ampere
Change-Id: I6ff219170a16c0081fba7297110e8dfaadcff401
Signed-off-by: Xindong Xu <xindong.xu@amlogic.com>
Yan Wang [Thu, 30 Nov 2017 08:40:26 +0000 (16:40 +0800)]
DolbyFW: Dolby Firmware Protection Driver create [1/1]
PD#SWPL-739
Problem:
Dolby Firmware Protection Driver create.
Solution:
AXG support Dolby Firmware Protection.
Verify:
AXG S400
Change-Id: Id88ba3f99103f2978827a3394203f7eef6d889f4
Signed-off-by: Yan Wang <yan.wang@amlogic.com>
Nan Li [Tue, 20 Nov 2018 03:43:26 +0000 (11:43 +0800)]
emmc: clean emmc reg val for probe [1/1]
PD#SWPL-2286
Problem:
emmc response crc error in emmc init.
Solution:
clean emmc reg val from uboot to kernel.
Verify:
w400
Change-Id: I6a4763187f18e9e284c887c5c788f3a88c8548ff
Signed-off-by: Nan Li <nan.li@amlogic.com>
yeping.miao [Fri, 31 Aug 2018 01:49:13 +0000 (09:49 +0800)]
arm64: dts: p230: add dvb module
PD#172865
Problem:
Customer requests a new release for linux dvb
Need enable dvb for QA testing
Solution:
Need enable dvb for QA testing
Verify:
Change-Id: Ib082c457d6f43ef4d6a5d16059a7e8ce068a332e
Signed-off-by: yeping.miao <yeping.miao@amlogic.com>
Xindong Xu [Tue, 16 Oct 2018 06:41:30 +0000 (14:41 +0800)]
reboot: reason: add reboot_reason quiescent [1/4]
PD#SWPL-1887
Problem:
Android TV need reboot_reason quiescent
Solution:
add reboot_reason quiescent
Verify:
ampere
Change-Id: Ie5a748faae05be93c56722b7806df6179116a047
Signed-off-by: Xindong Xu <xindong.xu@amlogic.com>
Shunzhou Jiang [Fri, 16 Nov 2018 07:54:52 +0000 (15:54 +0800)]
clk: g12a/g12b: fix 32bit set mpll clk overflow [1/1]
PD#SWPL-1933
Problem:
32bit system clk overflow
Solution:
let mpll clock not overflow
Verify:
g12b
Change-Id: Ie1c7c611e637776348bb35a3e0c1624cee57716f
Signed-off-by: shunzhou.jiang <shunzhou.jiang@amlogic.com>
Dezhi Kong [Wed, 14 Nov 2018 07:40:09 +0000 (15:40 +0800)]
vdin: enable vdin0 urgent for T950 default [1/1]
PD#TV-288
Problem:
There is flicker and jitter in HDMI
Solution:
enable vdin0 urgent for T950 default
Verify:
p321-T950
Change-Id: I17e472d7a47411093e9ade70a342807bed060a3a
Signed-off-by: Dezhi Kong <dezhi.kong@amlogic.com>
wenfeng.guo [Thu, 15 Nov 2018 08:11:08 +0000 (16:11 +0800)]
deinterlace: fix di coverity & di_trace [1/1]
PD#SWPL-2138
Problem:
Fix di coverity & di_trace
Solution:
fix di coverity & di
Verify:
T962X-R311
Change-Id: I9be91832eeed89ebd715276c75414e4e6da55240
Signed-off-by: wenfeng.guo <wenfeng.guo@amlogic.com>
nengwen.chen [Mon, 12 Nov 2018 07:23:04 +0000 (15:23 +0800)]
atv_demod: Output big "PO" sound when change source from ATV [1/3]
PD#SWPL-318
Problem:
Output big "PO" sound when change source from ATV to others,
or switch between small window and full screen in ATV source.
Solution:
disable atv status early when exit ATV source.
Verify:
verified by p321
Change-Id: I82af7f8eaef181f1f72ef1f9d194e33c1efdcdb5
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Nan Li [Tue, 30 Oct 2018 11:33:47 +0000 (19:33 +0800)]
sdio: optimize sd & wifi TDMA [1/1]
PD#SWPL-1908
Problem:
sdio wifi error TDMA.
Solution:
optimize host reg value set error.
Verify:
u211 & u212
Change-Id: I0e0d52ac2bce42cf163f0065d46badc938832a65
Signed-off-by: Nan Li <nan.li@amlogic.com>
wenfeng.guo [Tue, 9 Oct 2018 10:03:28 +0000 (18:03 +0800)]
di: fix dump_status log error [1/1]
PD#174473
Problem:
dump_status log error
Solution:
fix dump_status log error
Verify:
verified in t962X_r311 board
Change-Id: I53cec7b93f6e2649bd527b8591995d54bec6450d
Signed-off-by: wenfeng.guo <wenfeng.guo@amlogic.com>
Bencheng Jing [Sat, 28 Apr 2018 11:10:10 +0000 (19:10 +0800)]
drm: pq: G12A DRM support gamma and ctm setting [1/1]
PD#165492
Problem:
G12A DRM add gamma and ctm setting support
Solution:
1. amvecm: add gamma apis for drm
2. drm: add gamma and ctm setting
Verify:
Verified on customer platfor
Change-Id: Iff5204ae7f719542463ac15140e471cd762c9c27
Signed-off-by: Bencheng Jing <bencheng.jing@amlogic.com>
Yi Zhou [Tue, 6 Nov 2018 11:43:35 +0000 (19:43 +0800)]
dv: set avi info limited range when dv output hdr mode [1/1]
PD#SWPL-1127
Problem:
when dv output hdr mode, the quantization range is default value
instead of limited range
Solution:
set quantization range to limited range in avi info
Verify:
t962e (txlx)
Change-Id: Ib4fbeb1c7efcedd7194143772ee5c663284a1c77
Signed-off-by: Yi Zhou <yi.zhou@amlogic.com>
Jianxiong Pan [Wed, 14 Nov 2018 02:11:35 +0000 (10:11 +0800)]
dts: modify the remaining 64bit dts to support 32bit [1/1]
PD#SWPL-2046
Problem:
some of the remaining 64bit boards do not support 32bit.
Solution:
modify the dts to support 32bit.
Verify:
axg, g12a, g12b, gxl, gxm, txl, txlx.
Change-Id: I951f8d32b18243a64e2abc5008bbb015c2e21e7a
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
Peng Yixin [Tue, 13 Nov 2018 07:21:30 +0000 (15:21 +0800)]
media: fix some coverity error: [1/1]
PD#SWPL-2053
Problem:
Coverity detected some code defects.
Solution:
Fixed these code defects.
Verify:
Verified u212
Change-Id: Ie3c0907c7ee3db94f65f58aa5d5c96812a7fe38c
Signed-off-by: Peng Yixin <yixin.peng@amlogic.com>
Nanxin Qin [Thu, 25 Oct 2018 02:42:17 +0000 (10:42 +0800)]
media: remap the addr to prevent crash on the 32bit & 2G board [1/1]
PD#SWPL-1909
Problem:
mem rw exception caused crashed.
Solution:
1. add mapping the highmem address by the func vmap().
2. remove the flag CODEC_MM_FLAGS_CPU if not necessary.
Verify:
p212, w400
Change-Id: I982c775d7c009335cae5802f0eb6287d22037db6
Signed-off-by: Nanxin Qin <nanxin.qin@amlogic.com>
tao zeng [Fri, 9 Nov 2018 04:10:49 +0000 (12:10 +0800)]
dts: change CMA layout [1/1]
PD#SWPL-1909
Problem:
On 32bit kernel, codec cma is located in normal zone by
"alloc-ranges" parameter with large size. This takse up
memory space for kernel and drivers. Sometimes we can see
memory allocation fail log but there are still enought
free pages. But most of these pages are CMA pages.
Solution:
Move codec cma location to high memzone. On 32bit, low
768MB memory is normal zone.
This change also correct first 1MB memory lost problem
for chips later than TXLX
Verify:
P212
Change-Id: I4592d34d08ee4dbb6700bbbfc4e0fadaceab0310
Signed-off-by: tao zeng <tao.zeng@amlogic.com>
huaihao.guo [Fri, 2 Nov 2018 11:10:19 +0000 (19:10 +0800)]
deinterface: add afbc support on g12a and txlx [1/1]
PD#SWPL-1618
Problem:
Add afbc support on g12a and txlx
Solution:
add afbc support on g12a and txlx
Verify:
T962X-R311, U200(G12A)
Change-Id: Ia0cce8516a98653b01c3bc628e812c3a81b1df59
Signed-off-by: huaihao.guo <huaihao.guo@amlogic.com>
Huan Biao [Thu, 15 Nov 2018 07:24:23 +0000 (15:24 +0800)]
thermal: sensor: fix thermal disabled mode issue [1/1]
PD#SWPL-2130
Problem:
tsensor driver update thermal event when mode disabled
Solution:
fix tsensor disable mode issue
Verify:
A311D W400 pass
Change-Id: If9e3d3ea15732a0efbd8314003b27bc0bdf3e476
Signed-off-by: Huan Biao <huan.biao@amlogic.com>
MingLiang Dong [Thu, 11 Oct 2018 03:20:17 +0000 (23:20 -0400)]
amvecm: overscan: fix video local play, screen mode set error [1/1]
PD#SWPL-206
Problem:
overscan set error when local play
Solution:
overscan don't set at vpp
Verify:
verify on txlx
Change-Id: Ifd4ad4f5fcdb9fbc7ad05a540d0ed11b24d4ca66
Signed-off-by: MingLiang Dong <mingliang.dong@amlogic.com>
live.li [Wed, 14 Nov 2018 02:15:00 +0000 (10:15 +0800)]
tsync: tsync change the apts set code [1/2]
PD#SWPL-1774
Problem:
DD program has avysnc problem over one night play
Solution:
fix the apts set bug
Verify:
p321
Change-Id: I0f6a5b47d3e3171a3dd8fa9a0b721cd11ec20b9e
Signed-off-by: live.li <live.li@amlogic.com>
Zongdong Jiao [Fri, 9 Nov 2018 06:57:29 +0000 (14:57 +0800)]
hdmitx: remove a wrong Y422 format judgement [1/1]
PD#IPTV-55
Problem:
When connect to a Samsung TV(support 4k60 422 12bit), get a wrong
0 of 'echo 2160p60hz422,12bit > valid_mode'
Solution:
Remove a wrong Y422 format judgement
Verify:
P212
Change-Id: Ic0f2cefc1e0893390ac38298b55272877d81e04b
Signed-off-by: Zongdong Jiao <zongdong.jiao@amlogic.com>
Zongdong Jiao [Sat, 29 Sep 2018 10:16:08 +0000 (18:16 +0800)]
hdmitx: enable repeater_tx in r321/atom dts [2/3]
PD#SWPL-1303
Problem:
For TXLX/T962E/R321 cases, there are both HDMI TX and RX.
Should consider it as repeater.
Solution:
Enable repeater_tx in r321/atom dts
Also, add a missing ksv_lists[] clear.
Verify:
r321/atom
Change-Id: I7b512c34123481380220f9262466fde56b0ae6e3
Signed-off-by: Zongdong Jiao <zongdong.jiao@amlogic.com>
Jian Xu [Wed, 7 Nov 2018 14:00:44 +0000 (22:00 +0800)]
audio: fix audio driver del_timer BUG_ON crash issue [1/1]
PD#SWPL-972
Problem:
audio crash when ATV switch channel long time burning test
Solution:
there is a risk to fetch the timer lock. when input stop, stop_timer
will call del_timer, at the same time the function
"aml_i2s_hrtimer_callback" is waiting for the timer lock,after
stop_timer release the lock,"aml_i2s_hrtimer_callback" get the
lock and call mod_timer again, which will set the timer to pending
status. It will cause the next "start input" stage,add_timer will
trigger BUG_ON.Now we put the lock before the active status
checking then we will not touch the timer.
Verify:
Need burning test
Change-Id: I1fb66903a4d31e9491ac0533e477e1597575d4cf
Signed-off-by: Jian Xu <jian.xu@amlogic.com>
Hong Guo [Fri, 9 Nov 2018 07:18:20 +0000 (15:18 +0800)]
arm64: dts: g12a: fine-tune voltage OPP [1/1]
PD#165143
Probleļ¼
fine-tune voltage OPP
Solution:
fine-tune voltage OPP
Verify:
G12A/G12B,PASS
Change-Id: I0b3fb0e4624e2ddfa635c8225a740ed7a8ff3e51
Signed-off-by: Hong Guo <hong.guo@amlogic.com>
Bo Yang [Sat, 3 Nov 2018 02:22:02 +0000 (10:22 +0800)]
arm: dts: gxl: replace watchdog with new version [1/1]
PD#SWPL-1600
Problem:
The current watchdog is not the upstream standard driver.
Solution:
Replace watchdog device tree to use the standard watchdog driver.
Verify:
S905X P215/P212 Android-32bit Kernel-32bit.
Change-Id: I972c8ebb0158caa2df393d9a2d687d9298181102
Signed-off-by: Bo Yang <bo.yang@amlogic.com>
wenbiao zhang [Fri, 12 Oct 2018 07:28:54 +0000 (15:28 +0800)]
ddr: detect bandwidth except mali and reduce bandwidth [2/3]
PD#SWPL-122
Problem:
ddr bandwidth is tightly in many cases, such as HDR/4K video playing,
and then refresh osd at the same time
Solution:
in most cases the problem is refreshing osd when bandwidth tightly,
so detect ddr bandwidth usage except mali and reduce it when it is tightly
Verify:
verify by p321/r311
Change-Id: Ia594f08dbe9a8a7a8d78b5104c93bddaa8229c0b
Signed-off-by: wenbiao zhang <wenbiao.zhang@amlogic.com>
Jianxiong Pan [Wed, 7 Nov 2018 07:27:43 +0000 (15:27 +0800)]
dts: fix some errors on g12b_w400 for 32bit [1/1]
PD#SWPL-1010
Problem:
some errors of reg address.
Solution:
modify to support 32bit.
Verify:
w400.
Change-Id: Ia35e95ac59084a9c57a9a4ab32fecb64f78c772e
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
pengcheng chen [Mon, 29 Oct 2018 07:08:04 +0000 (15:08 +0800)]
osd: add hdr mode set via meson-hwc support [1/1]
PD#163001
Problem:
hdr mode set not supported
Solution:
add hdr mode set via meson-hwc support
Verify:
verified in u200 board
Change-Id: Iaad75982003870f9469e4155aedb9c13349b60b9
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
pengcheng chen [Mon, 5 Nov 2018 08:59:10 +0000 (16:59 +0800)]
osd: uboot logo scaler down in 4k issue [1/1]
PD#163001
Problem:
uboot logo scaler down in 4k
Solution:
uboot logo size adjust when vout changed before
first page flip command
Verify:
verified in u200 board
Change-Id: Ic23e695fe716811eaf3faa62069c808a03c26f9d
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
Jianxiong Pan [Fri, 9 Nov 2018 09:02:52 +0000 (17:02 +0800)]
smartcard: fix defects for coverity [1/1]
PD#166793
Problem:
conditional statement not is valid.
Solution:
change type u32 to type int.
Verify:
module owner confirmed.
Change-Id: I9fdfa444b29104c7afc9b7a380748ebe82ed390b
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
pengcheng chen [Thu, 1 Nov 2018 12:22:29 +0000 (20:22 +0800)]
osd: osd shift-workaround one line fixed [1/1]
PD#163001
Problem:
current osd code have one line missing issue in meson-hwc
Solution:
osd blend used +1 line to fix shift issue,
and used freescale to cut it.
Verify:
verified in u200 board
Change-Id: I2354742d456327d9f1aa5713ee782648895034db
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
pengcheng chen [Wed, 31 Oct 2018 11:32:59 +0000 (19:32 +0800)]
osd: meson-hwc screen always blank [1/1]
PD#163001
Problem:
TL1 code merged caused meson-hwc screen always blank
Solution:
fix meson-hwc screen always blank
Verify:
verified in u200 board
Change-Id: I0a9371b42546e2713e6dcb926e7c94598e29da1d
Signed-off-by: pengcheng chen <pengcheng.chen@amlogic.com>
Nian Jing [Thu, 1 Nov 2018 12:55:47 +0000 (20:55 +0800)]
vout: add bist test on vout [1/1]
PD#SWPL-1630
Problem:
add cvbs/hdmi/lcd bist test on vout
Solution:
add cvbs bist test on vout
Verify:
test pass on u200/p212
Change-Id: Ie61d9b0d63649ec3022fd720068b689f4d721e3b
Signed-off-by: Nian Jing <nian.jing@amlogic.com>
Yong Qin [Tue, 6 Nov 2018 01:31:51 +0000 (09:31 +0800)]
cec: for support multi-logical address [1/1]
PD#SWPL-418
Problem:
cec: support multi-logical address
Solution:
if working on multi-logical address, enable two ip
1.enable cec_a, cec_b
2.enable two interrupt
3.enable two pinmux oa_7, ao_8
4.cec_a only send all msg
5.cec_b only receive all msg
6.discard ceca broadcast msg
Verify:
r311
r321
p321
Change-Id: I1dc93429876ede951657102bcd7d41a500946719
Signed-off-by: Yong Qin <yong.qin@amlogic.com>
nengwen.chen [Thu, 8 Nov 2018 11:57:53 +0000 (19:57 +0800)]
atv_demod: pc bad value in panic after change source [1/1]
PD#SWPL-1636
Problem:
1.pc bad value in kernel panic after change source.
2.System crash down when change source.
Solution:
optimize atv demod code.
Verify:
verified by p321
Change-Id: I655d1253950475dfb49ae1b174597797000adb73
Signed-off-by: nengwen.chen <nengwen.chen@amlogic.com>
Dezhi Kong [Tue, 30 Oct 2018 09:30:48 +0000 (17:30 +0800)]
vlock: optimize vlock process for interlace input [1/1]
PD#SWPL-743
Problem:
The picthre is shaking when press DVD remote
control in AV source
Solution:
add delay work for vlock process interlace input
Verify:
T962X-R311
Change-Id: Ic2ed077e0684ecc6b0990336e7a4ab7022931886
Signed-off-by: Dezhi Kong <dezhi.kong@amlogic.com>
Jianxiong Pan [Fri, 9 Nov 2018 11:22:53 +0000 (19:22 +0800)]
script: segments can appear in descriptive information [1/1]
PD#174488
Problem:
segmentation in descriptive information is reasonable and
should be allowed.
Solution:
modify the check codes.
Verify:
test locally.
Change-Id: I5e34ef2dd26077bb54adee7597a1aa3c789566c9
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
Huan Biao [Fri, 9 Nov 2018 09:09:54 +0000 (17:09 +0800)]
vccktest: add vccktest dts for buildroot [1/1]
PD#174851
Problem:
buildroot no vccktest dts
Solution:
add vccktest dts
Verify:
g12a/g12b test pass
Change-Id: I6907fa3cfc087ac84395956ddbda678f7a5e3f4b
Signed-off-by: Huan Biao <huan.biao@amlogic.com>
Jianxiong Pan [Fri, 9 Nov 2018 07:11:30 +0000 (15:11 +0800)]
dts: modified atom.dts support 32bit. [1/1]
PD#SWPL-1942
Problem:
add atom.dts support 32bit.
Solution:
modified length of reg, mem etc.
Verify:
r321
Change-Id: I2a518af2a76b8cb17ded68e994c3065072b92b9c
Signed-off-by: Jianxiong Pan <jianxiong.pan@amlogic.com>
Jun Zhang [Wed, 7 Nov 2018 07:59:16 +0000 (15:59 +0800)]
dts: add isp and galcore support to w400-buildroot [1/2]
PD#SWPL-1819
Problem:
lack of isp and galcore support in buildroot dts
Solution:
merge configurations from skt board
Verify:
local
Change-Id: I5936341fc24719f345c7707e16e692ae292ca6fe
Signed-off-by: Jun Zhang <jun.zhang@amlogic.com>
Zhi Zhou [Wed, 27 Jun 2018 07:44:45 +0000 (15:44 +0800)]
video: merged from A wait AFBC idle when report state [1/1]
PD#169128:
[Problem]
When quick switch video between 2 vsync isr, the AFBC may read wrong
data, and green screen or distortion image occurs.
[Solution]
1. Add delay when get video layer state, to make sure afbc is stopped
2. Remove ambiguous log print
[Platform]
Blanche
BranchTo: NONE
[Test]
Change-Id: I94ccf25373f29ce188829ab1b7db6f9df1fb49ad
Signed-off-by: Zhi Zhou <zhi.zhou@amlogic.com>
projects / platform / kernel / linux-amlogic.git / log