Lukas Wunner [Sat, 31 Jul 2021 12:39:01 +0000 (14:39 +0200)]
PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
[ Upstream commit
ea401499e943c307e6d44af6c2b4e068643e7884 ]
Stuart Hayes reports that an error handled by DPC at a Root Port results
in pciehp gratuitously bringing down a subordinate hotplug port:
RP -- UP -- DP -- UP -- DP (hotplug) -- EP
pciehp brings the slot down because the Link to the Endpoint goes down.
That is caused by a Hot Reset being propagated as a result of DPC.
Per PCIe Base Spec 5.0, section 6.6.1 "Conventional Reset":
For a Switch, the following must cause a hot reset to be sent on all
Downstream Ports: [...]
* The Data Link Layer of the Upstream Port reporting DL_Down status.
In Switches that support Link speeds greater than 5.0 GT/s, the
Upstream Port must direct the LTSSM of each Downstream Port to the
Hot Reset state, but not hold the LTSSMs in that state. This permits
each Downstream Port to begin Link training immediately after its
hot reset completes. This behavior is recommended for all Switches.
* Receiving a hot reset on the Upstream Port.
Once DPC recovers, pcie_do_recovery() walks down the hierarchy and
invokes pcie_portdrv_slot_reset() to restore each port's config space.
At that point, a hotplug interrupt is signaled per PCIe Base Spec r5.0,
section 6.7.3.4 "Software Notification of Hot-Plug Events":
If the Port is enabled for edge-triggered interrupt signaling using
MSI or MSI-X, an interrupt message must be sent every time the logical
AND of the following conditions transitions from FALSE to TRUE: [...]
* The Hot-Plug Interrupt Enable bit in the Slot Control register is
set to 1b.
* At least one hot-plug event status bit in the Slot Status register
and its associated enable bit in the Slot Control register are both
set to 1b.
Prevent pciehp from gratuitously bringing down the slot by clearing the
error-induced Data Link Layer State Changed event before restoring
config space. Afterwards, check whether the link has unexpectedly
failed to retrain and synthesize a DLLSC event if so.
Allow each pcie_port_service_driver (one of them being pciehp) to define
a slot_reset callback and re-use the existing pm_iter() function to
iterate over the callbacks.
Thereby, the Endpoint driver remains bound throughout error recovery and
may restore the device to working state.
Surprise removal during error recovery is detected through a Presence
Detect Changed event. The hotplug port is expected to not signal that
event as a result of a Hot Reset.
The issue isn't DPC-specific, it also occurs when an error is handled by
AER through aer_root_reset(). So while the issue was noticed only now,
it's been around since 2006 when AER support was first introduced.
[bhelgaas: drop PCI_ERROR_RECOVERY Kconfig, split pm_iter() rename to
preparatory patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Fixes:
6c2b374d7485 ("PCI-Express AER implemetation: AER core and aerdriver")
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Reported-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v2.6.19+: ba952824e6c1: PCI/portdrv: Report reset for frozen channel
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Lukas Wunner [Fri, 15 Oct 2021 18:58:40 +0000 (13:58 -0500)]
PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
[ Upstream commit
3134689f98f9e09004a4727370adc46e7635b4be ]
Rename pm_iter() to pcie_port_device_iter() and make it visible outside
CONFIG_PM and portdrv_core.c so it can be used for pciehp slot reset
recovery.
[bhelgaas: split into its own patch]
Link: https://lore.kernel.org/linux-pci/08c046b0-c9f2-3489-eeef-7e7aca435bb9@gmail.com/
Link: https://lore.kernel.org/r/251f4edcc04c14f873ff1c967bc686169cd07d2d.1627638184.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Ville Syrjälä [Thu, 14 Oct 2021 09:09:38 +0000 (12:09 +0300)]
drm/i915: Replace the unconditional clflush with drm_clflush_virt_range()
[ Upstream commit
ef7ec41f17cbc0861891ccc0634d06a0c8dcbf09 ]
Not all machines have clflush, so don't go assuming they do.
Not really sure why the clflush is even here since hwsp
is supposed to get snooped I thought.
Although in my case we're talking about a i830 machine where
render/blitter snooping is definitely busted. But it might
work for the hswp perhaps. Haven't really reverse engineered
that one fully.
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes:
b436a5f8b6c8 ("drm/i915/gt: Track all timelines created using the HWSP")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014090941.12159-2-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Hellström [Wed, 22 Sep 2021 06:25:23 +0000 (08:25 +0200)]
drm/i915/gt: Register the migrate contexts with their engines
[ Upstream commit
3e42cc61275f95fd7f022b6380b95428efe134d3 ]
Pinned contexts, like the migrate contexts need reset after resume
since their context image may have been lost. Also the GuC needs to
register pinned contexts.
Add a list to struct intel_engine_cs where we add all pinned contexts on
creation, and traverse that list at resume time to reset the pinned
contexts.
This fixes the kms_pipe_crc_basic@suspend-read-crc-pipe-a selftest for now,
but proper LMEM backup / restore is needed for full suspend functionality.
However, note that even with full LMEM backup / restore it may be
desirable to keep the reset since backing up the migrate context images
must happen using memcpy() after the migrate context has become inactive,
and for performance- and other reasons we want to avoid memcpy() from
LMEM.
Also traverse the list at guc_init_lrc_mapping() calling
guc_kernel_context_pin() for the pinned contexts, like is already done
for the kernel context.
v2:
- Don't reset the contexts on each __engine_unpark() but rather at
resume time (Chris Wilson).
v3:
- Reset contexts in the engine sanitize callback. (Chris Wilson)
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Brost Matthew <matthew.brost@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922062527.865433-6-thomas.hellstrom@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Matthew Brost [Wed, 28 Jul 2021 19:21:00 +0000 (12:21 -0700)]
drm/i915: Disable bonding on gen12+ platforms
[ Upstream commit
ce7e75c7ef1bf8ea3d947da8c674d2f40fd7d734 ]
Disable bonding on gen12+ platforms aside from ones already supported by
the i915 - TGL, RKL, and ADL-S.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728192100.132425-1-matthew.brost@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filipe Manana [Wed, 13 Oct 2021 09:12:49 +0000 (10:12 +0100)]
btrfs: fix deadlock between chunk allocation and chunk btree modifications
[ Upstream commit
2bb2e00ed9787e52580bb651264b8d6a2b7a9dd2 ]
When a task is doing some modification to the chunk btree and it is not in
the context of a chunk allocation or a chunk removal, it can deadlock with
another task that is currently allocating a new data or metadata chunk.
These contexts are the following:
* When relocating a system chunk, when we need to COW the extent buffers
that belong to the chunk btree;
* When adding a new device (ioctl), where we need to add a new device item
to the chunk btree;
* When removing a device (ioctl), where we need to remove a device item
from the chunk btree;
* When resizing a device (ioctl), where we need to update a device item in
the chunk btree and may need to relocate a system chunk that lies beyond
the new device size when shrinking a device.
The problem happens due to a sequence of steps like the following:
1) Task A starts a data or metadata chunk allocation and it locks the
chunk mutex;
2) Task B is relocating a system chunk, and when it needs to COW an extent
buffer of the chunk btree, it has locked both that extent buffer as
well as its parent extent buffer;
3) Since there is not enough available system space, either because none
of the existing system block groups have enough free space or because
the only one with enough free space is in RO mode due to the relocation,
task B triggers a new system chunk allocation. It blocks when trying to
acquire the chunk mutex, currently held by task A;
4) Task A enters btrfs_chunk_alloc_add_chunk_item(), in order to insert
the new chunk item into the chunk btree and update the existing device
items there. But in order to do that, it has to lock the extent buffer
that task B locked at step 2, or its parent extent buffer, but task B
is waiting on the chunk mutex, which is currently locked by task A,
therefore resulting in a deadlock.
One example report when the deadlock happens with system chunk relocation:
INFO: task kworker/u9:5:546 blocked for more than 143 seconds.
Not tainted 5.15.0-rc3+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u9:5 state:D stack:25936 pid: 546 ppid: 2 flags:0x00004000
Workqueue: events_unbound btrfs_async_reclaim_metadata_space
Call Trace:
context_switch kernel/sched/core.c:4940 [inline]
__schedule+0xcd9/0x2530 kernel/sched/core.c:6287
schedule+0xd3/0x270 kernel/sched/core.c:6366
rwsem_down_read_slowpath+0x4ee/0x9d0 kernel/locking/rwsem.c:993
__down_read_common kernel/locking/rwsem.c:1214 [inline]
__down_read kernel/locking/rwsem.c:1223 [inline]
down_read_nested+0xe6/0x440 kernel/locking/rwsem.c:1590
__btrfs_tree_read_lock+0x31/0x350 fs/btrfs/locking.c:47
btrfs_tree_read_lock fs/btrfs/locking.c:54 [inline]
btrfs_read_lock_root_node+0x8a/0x320 fs/btrfs/locking.c:191
btrfs_search_slot_get_root fs/btrfs/ctree.c:1623 [inline]
btrfs_search_slot+0x13b4/0x2140 fs/btrfs/ctree.c:1728
btrfs_update_device+0x11f/0x500 fs/btrfs/volumes.c:2794
btrfs_chunk_alloc_add_chunk_item+0x34d/0xea0 fs/btrfs/volumes.c:5504
do_chunk_alloc fs/btrfs/block-group.c:3408 [inline]
btrfs_chunk_alloc+0x84d/0xf50 fs/btrfs/block-group.c:3653
flush_space+0x54e/0xd80 fs/btrfs/space-info.c:670
btrfs_async_reclaim_metadata_space+0x396/0xa90 fs/btrfs/space-info.c:953
process_one_work+0x9df/0x16d0 kernel/workqueue.c:2297
worker_thread+0x90/0xed0 kernel/workqueue.c:2444
kthread+0x3e5/0x4d0 kernel/kthread.c:319
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
INFO: task syz-executor:9107 blocked for more than 143 seconds.
Not tainted 5.15.0-rc3+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz-executor state:D stack:23200 pid: 9107 ppid: 7792 flags:0x00004004
Call Trace:
context_switch kernel/sched/core.c:4940 [inline]
__schedule+0xcd9/0x2530 kernel/sched/core.c:6287
schedule+0xd3/0x270 kernel/sched/core.c:6366
schedule_preempt_disabled+0xf/0x20 kernel/sched/core.c:6425
__mutex_lock_common kernel/locking/mutex.c:669 [inline]
__mutex_lock+0xc96/0x1680 kernel/locking/mutex.c:729
btrfs_chunk_alloc+0x31a/0xf50 fs/btrfs/block-group.c:3631
find_free_extent_update_loop fs/btrfs/extent-tree.c:3986 [inline]
find_free_extent+0x25cb/0x3a30 fs/btrfs/extent-tree.c:4335
btrfs_reserve_extent+0x1f1/0x500 fs/btrfs/extent-tree.c:4415
btrfs_alloc_tree_block+0x203/0x1120 fs/btrfs/extent-tree.c:4813
__btrfs_cow_block+0x412/0x1620 fs/btrfs/ctree.c:415
btrfs_cow_block+0x2f6/0x8c0 fs/btrfs/ctree.c:570
btrfs_search_slot+0x1094/0x2140 fs/btrfs/ctree.c:1768
relocate_tree_block fs/btrfs/relocation.c:2694 [inline]
relocate_tree_blocks+0xf73/0x1770 fs/btrfs/relocation.c:2757
relocate_block_group+0x47e/0xc70 fs/btrfs/relocation.c:3673
btrfs_relocate_block_group+0x48a/0xc60 fs/btrfs/relocation.c:4070
btrfs_relocate_chunk+0x96/0x280 fs/btrfs/volumes.c:3181
__btrfs_balance fs/btrfs/volumes.c:3911 [inline]
btrfs_balance+0x1f03/0x3cd0 fs/btrfs/volumes.c:4301
btrfs_ioctl_balance+0x61e/0x800 fs/btrfs/ioctl.c:4137
btrfs_ioctl+0x39ea/0x7b70 fs/btrfs/ioctl.c:4949
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:874 [inline]
__se_sys_ioctl fs/ioctl.c:860 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:860
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
So fix this by making sure that whenever we try to modify the chunk btree
and we are neither in a chunk allocation context nor in a chunk remove
context, we reserve system space before modifying the chunk btree.
Reported-by: Hao Sun <sunhao.th@gmail.com>
Link: https://lore.kernel.org/linux-btrfs/CACkBjsax51i4mu6C0C3vJqQN3NR_iVuucoeG3U1HXjrgzn5FFQ@mail.gmail.com/
Fixes:
79bd37120b1495 ("btrfs: rework chunk allocation to avoid exhaustion of the system chunk array")
CC: stable@vger.kernel.org # 5.14+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michel Dänzer [Fri, 23 Jul 2021 07:58:57 +0000 (09:58 +0200)]
dma-buf/poll: Get a file reference for outstanding fence callbacks
[ Upstream commit
ff2d23843f7fb4f13055be5a4a9a20ddd04e6e9c ]
This makes sure we don't hit the
BUG_ON(dmabuf->cb_in.active || dmabuf->cb_out.active);
in dma_buf_release, which could be triggered by user space closing the
dma-buf file description while there are outstanding fence callbacks
from dma_buf_poll.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723075857.4065-1-michel@daenzer.net
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Tue, 7 Dec 2021 07:15:09 +0000 (23:15 -0800)]
Input: goodix - try not to touch the reset-pin on x86/ACPI devices
[ Upstream commit
a2fd46cd3dbb83b373ba74f4043f8dae869c65f1 ]
Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.
Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.
But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit
921daeeca91b ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").
And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.
This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes:
a7d4b171660c ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Tue, 21 Sep 2021 04:08:26 +0000 (21:08 -0700)]
Input: goodix - refactor reset handling
[ Upstream commit
209bda4741f68f102cf2f272227bfc938e387b51 ]
Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.
Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Tue, 21 Sep 2021 04:08:18 +0000 (21:08 -0700)]
Input: goodix - add a goodix.h header file
[ Upstream commit
a2233cb7b65a017067e2f2703375ecc930a0ab30 ]
Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Tue, 21 Sep 2021 04:08:02 +0000 (21:08 -0700)]
Input: goodix - change goodix_i2c_write() len parameter type to int
[ Upstream commit
31ae0102a34ed863c7d32b10e768036324991679 ]
Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tang Bin [Mon, 6 Sep 2021 01:57:32 +0000 (18:57 -0700)]
Input: cpcap-pwrbutton - handle errors from platform_get_irq()
[ Upstream commit
58ae4004b9c4bb040958cf73986b687a5ea4d85d ]
The function cpcap_power_button_probe() does not perform
sufficient error checking after executing platform_get_irq(),
thus fix it.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210802121740.8700-1-tangbin@cmss.chinamobile.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filipe Manana [Mon, 13 Dec 2021 08:45:13 +0000 (08:45 +0000)]
btrfs: fix warning when freeing leaf after subvolume creation failure
[ Upstream commit
212a58fda9b9077e0efc20200a4feb76afacfd95 ]
When creating a subvolume, at ioctl.c:create_subvol(), if we fail to
insert the root item for the new subvolume into the root tree, we can
trigger the following warning:
[78961.741046] WARNING: CPU: 0 PID: 4079814 at fs/btrfs/extent-tree.c:3357 btrfs_free_tree_block+0x2af/0x310 [btrfs]
[78961.743344] Modules linked in:
[78961.749440] dm_snapshot dm_thin_pool (...)
[78961.773648] CPU: 0 PID: 4079814 Comm: fsstress Not tainted 5.16.0-rc4-btrfs-next-108 #1
[78961.775198] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[78961.777266] RIP: 0010:btrfs_free_tree_block+0x2af/0x310 [btrfs]
[78961.778398] Code: 17 00 48 85 (...)
[78961.781067] RSP: 0018:
ffffaa4001657b28 EFLAGS:
00010202
[78961.781877] RAX:
0000000000000213 RBX:
ffff897f8a796910 RCX:
0000000000000000
[78961.782780] RDX:
0000000000000000 RSI:
0000000011004000 RDI:
00000000ffffffff
[78961.783764] RBP:
ffff8981f490e800 R08:
0000000000000001 R09:
0000000000000000
[78961.784740] R10:
0000000000000000 R11:
0000000000000001 R12:
ffff897fc963fcc8
[78961.785665] R13:
0000000000000001 R14:
ffff898063548000 R15:
ffff898063548000
[78961.786620] FS:
00007f31283c6b80(0000) GS:
ffff8982ace00000(0000) knlGS:
0000000000000000
[78961.787717] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[78961.788598] CR2:
00007f31285c3000 CR3:
000000023fcc8003 CR4:
0000000000370ef0
[78961.789568] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[78961.790585] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[78961.791684] Call Trace:
[78961.792082] <TASK>
[78961.792359] create_subvol+0x5d1/0x9a0 [btrfs]
[78961.793054] btrfs_mksubvol+0x447/0x4c0 [btrfs]
[78961.794009] ? preempt_count_add+0x49/0xa0
[78961.794705] __btrfs_ioctl_snap_create+0x123/0x190 [btrfs]
[78961.795712] ? _copy_from_user+0x66/0xa0
[78961.796382] btrfs_ioctl_snap_create_v2+0xbb/0x140 [btrfs]
[78961.797392] btrfs_ioctl+0xd1e/0x35c0 [btrfs]
[78961.798172] ? __slab_free+0x10a/0x360
[78961.798820] ? rcu_read_lock_sched_held+0x12/0x60
[78961.799664] ? lock_release+0x223/0x4a0
[78961.800321] ? lock_acquired+0x19f/0x420
[78961.800992] ? rcu_read_lock_sched_held+0x12/0x60
[78961.801796] ? trace_hardirqs_on+0x1b/0xe0
[78961.802495] ? _raw_spin_unlock_irqrestore+0x3e/0x60
[78961.803358] ? kmem_cache_free+0x321/0x3c0
[78961.804071] ? __x64_sys_ioctl+0x83/0xb0
[78961.804711] __x64_sys_ioctl+0x83/0xb0
[78961.805348] do_syscall_64+0x3b/0xc0
[78961.805969] entry_SYSCALL_64_after_hwframe+0x44/0xae
[78961.806830] RIP: 0033:0x7f31284bc957
[78961.807517] Code: 3c 1c 48 f7 d8 (...)
This is because we are calling btrfs_free_tree_block() on an extent
buffer that is dirty. Fix that by cleaning the extent buffer, with
btrfs_clean_tree_block(), before freeing it.
This was triggered by test case generic/475 from fstests.
Fixes:
67addf29004c5b ("btrfs: fix metadata extent leak after failure to create subvolume")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Filipe Manana [Mon, 13 Dec 2021 08:45:12 +0000 (08:45 +0000)]
btrfs: fix invalid delayed ref after subvolume creation failure
[ Upstream commit
7a1636089acfee7562fe79aff7d1b4c57869896d ]
When creating a subvolume, at ioctl.c:create_subvol(), if we fail to
insert the new root's root item into the root tree, we are freeing the
metadata extent we reserved for the new root to prevent a metadata
extent leak, as we don't abort the transaction at that point (since
there is nothing at that point that is irreversible).
However we allocated the metadata extent for the new root which we are
creating for the new subvolume, so its delayed reference refers to the
ID of this new root. But when we free the metadata extent we pass the
root of the subvolume where the new subvolume is located to
btrfs_free_tree_block() - this is incorrect because this will generate
a delayed reference that refers to the ID of the parent subvolume's root,
and not to ID of the new root.
This results in a failure when running delayed references that leads to
a transaction abort and a trace like the following:
[3868.738042] RIP: 0010:__btrfs_free_extent+0x709/0x950 [btrfs]
[3868.739857] Code: 68 0f 85 e6 fb ff (...)
[3868.742963] RSP: 0018:
ffffb0e9045cf910 EFLAGS:
00010246
[3868.743908] RAX:
00000000fffffffe RBX:
00000000fffffffe RCX:
0000000000000002
[3868.745312] RDX:
00000000fffffffe RSI:
0000000000000002 RDI:
ffff90b0cd793b88
[3868.746643] RBP:
000000000e5d8000 R08:
0000000000000000 R09:
ffff90b0cd793b88
[3868.747979] R10:
0000000000000002 R11:
00014ded97944d68 R12:
0000000000000000
[3868.749373] R13:
ffff90b09afe4a28 R14:
0000000000000000 R15:
ffff90b0cd793b88
[3868.750725] FS:
00007f281c4a8b80(0000) GS:
ffff90b3ada00000(0000) knlGS:
0000000000000000
[3868.752275] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[3868.753515] CR2:
00007f281c6a5000 CR3:
0000000108a42006 CR4:
0000000000370ee0
[3868.754869] DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
[3868.756228] DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
[3868.757803] Call Trace:
[3868.758281] <TASK>
[3868.758655] ? btrfs_merge_delayed_refs+0x178/0x1c0 [btrfs]
[3868.759827] __btrfs_run_delayed_refs+0x2b1/0x1250 [btrfs]
[3868.761047] btrfs_run_delayed_refs+0x86/0x210 [btrfs]
[3868.762069] ? lock_acquired+0x19f/0x420
[3868.762829] btrfs_commit_transaction+0x69/0xb20 [btrfs]
[3868.763860] ? _raw_spin_unlock+0x29/0x40
[3868.764614] ? btrfs_block_rsv_release+0x1c2/0x1e0 [btrfs]
[3868.765870] create_subvol+0x1d8/0x9a0 [btrfs]
[3868.766766] btrfs_mksubvol+0x447/0x4c0 [btrfs]
[3868.767669] ? preempt_count_add+0x49/0xa0
[3868.768444] __btrfs_ioctl_snap_create+0x123/0x190 [btrfs]
[3868.769639] ? _copy_from_user+0x66/0xa0
[3868.770391] btrfs_ioctl_snap_create_v2+0xbb/0x140 [btrfs]
[3868.771495] btrfs_ioctl+0xd1e/0x35c0 [btrfs]
[3868.772364] ? __slab_free+0x10a/0x360
[3868.773198] ? rcu_read_lock_sched_held+0x12/0x60
[3868.774121] ? lock_release+0x223/0x4a0
[3868.774863] ? lock_acquired+0x19f/0x420
[3868.775634] ? rcu_read_lock_sched_held+0x12/0x60
[3868.776530] ? trace_hardirqs_on+0x1b/0xe0
[3868.777373] ? _raw_spin_unlock_irqrestore+0x3e/0x60
[3868.778280] ? kmem_cache_free+0x321/0x3c0
[3868.779011] ? __x64_sys_ioctl+0x83/0xb0
[3868.779718] __x64_sys_ioctl+0x83/0xb0
[3868.780387] do_syscall_64+0x3b/0xc0
[3868.781059] entry_SYSCALL_64_after_hwframe+0x44/0xae
[3868.781953] RIP: 0033:0x7f281c59e957
[3868.782585] Code: 3c 1c 48 f7 d8 4c (...)
[3868.785867] RSP: 002b:
00007ffe1f83e2b8 EFLAGS:
00000202 ORIG_RAX:
0000000000000010
[3868.787198] RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
00007f281c59e957
[3868.788450] RDX:
00007ffe1f83e2c0 RSI:
0000000050009418 RDI:
0000000000000003
[3868.789748] RBP:
00007ffe1f83f300 R08:
0000000000000000 R09:
00007ffe1f83fe36
[3868.791214] R10:
0000000000000000 R11:
0000000000000202 R12:
0000000000000003
[3868.792468] R13:
0000000000000003 R14:
00007ffe1f83e2c0 R15:
00000000000003cc
[3868.793765] </TASK>
[3868.794037] irq event stamp: 0
[3868.794548] hardirqs last enabled at (0): [<
0000000000000000>] 0x0
[3868.795670] hardirqs last disabled at (0): [<
ffffffff98294214>] copy_process+0x934/0x2040
[3868.797086] softirqs last enabled at (0): [<
ffffffff98294214>] copy_process+0x934/0x2040
[3868.798309] softirqs last disabled at (0): [<
0000000000000000>] 0x0
[3868.799284] ---[ end trace
be24c7002fe27747 ]---
[3868.799928] BTRFS info (device dm-0): leaf
241188864 gen 1268 total ptrs 214 free space 469 owner 2
[3868.801133] BTRFS info (device dm-0): refs 2 lock_owner 225627 current 225627
[3868.802056] item 0 key (
237436928 169 0) itemoff 16250 itemsize 33
[3868.802863] extent refs 1 gen 1265 flags 2
[3868.803447] ref#0: tree block backref root 1610
(...)
[3869.064354] item 114 key (
241008640 169 0) itemoff 12488 itemsize 33
[3869.065421] extent refs 1 gen 1268 flags 2
[3869.066115] ref#0: tree block backref root 1689
(...)
[3869.403834] BTRFS error (device dm-0): unable to find ref byte nr
241008640 parent 0 root 1622 owner 0 offset 0
[3869.405641] BTRFS: error (device dm-0) in __btrfs_free_extent:3076: errno=-2 No such entry
[3869.407138] BTRFS: error (device dm-0) in btrfs_run_delayed_refs:2159: errno=-2 No such entry
Fix this by passing the new subvolume's root ID to btrfs_free_tree_block().
This requires changing the root argument of btrfs_free_tree_block() from
struct btrfs_root * to a u64, since at this point during the subvolume
creation we have not yet created the struct btrfs_root for the new
subvolume, and btrfs_free_tree_block() only needs a root ID and nothing
else from a struct btrfs_root.
This was triggered by test case generic/475 from fstests.
Fixes:
67addf29004c5b ("btrfs: fix metadata extent leak after failure to create subvolume")
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Borisov [Tue, 12 Oct 2021 08:21:35 +0000 (11:21 +0300)]
btrfs: add additional parameters to btrfs_init_tree_ref/btrfs_init_data_ref
[ Upstream commit
f42c5da6c12e990d8ec415199600b4d593c63bf5 ]
In order to make 'real_root' used only in ref-verify it's required to
have the necessary context to perform the same checks that this member
is used for. So add 'mod_root' which will contain the root on behalf of
which a delayed ref was created and a 'skip_group' parameter which
will contain callsite-specific override of skip_qgroup.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Nikolay Borisov [Wed, 18 Aug 2021 10:41:19 +0000 (13:41 +0300)]
btrfs: rename btrfs_alloc_chunk to btrfs_create_chunk
[ Upstream commit
f6f39f7a0add4e7fd120a709545b57586a1d0393 ]
The user facing function used to allocate new chunks is
btrfs_chunk_alloc, unfortunately there is yet another similar sounding
function - btrfs_alloc_chunk. This creates confusion, especially since
the latter function can be considered "private" in the sense that it
implements the first stage of chunk creation and as such is called by
btrfs_chunk_alloc.
To avoid the awkwardness that comes with having similarly named but
distinctly different in their purpose function rename btrfs_alloc_chunk
to btrfs_create_chunk, given that the main purpose of this function is
to orchestrate the whole process of allocating a chunk - reserving space
into devices, deciding on characteristics of the stripe size and
creating the in-memory structures.
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Anand Jain <anand.jain@oracle.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pablo Neira Ayuso [Sat, 2 Jul 2022 02:16:30 +0000 (04:16 +0200)]
netfilter: nf_tables: stricter validation of element data
commit
7e6bc1f6cabcd30aba0b11219d8e01b952eacbb6 upstream.
Make sure element data type and length do not mismatch the one specified
by the set declaration.
Fixes:
7d7402642eaf ("netfilter: nf_tables: variable sized set element keys / data")
Reported-by: Hugues ANGUELKOV <hanguelkov@randorisec.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Sat, 2 Jul 2022 02:16:31 +0000 (04:16 +0200)]
netfilter: nft_set_pipapo: release elements in clone from abort path
commit
9827a0e6e23bf43003cd3d5b7fb11baf59a35e1e upstream.
New elements that reside in the clone are not released in case that the
transaction is aborted.
[16302.231754] ------------[ cut here ]------------
[16302.231756] WARNING: CPU: 0 PID: 100509 at net/netfilter/nf_tables_api.c:1864 nf_tables_chain_destroy+0x26/0x127 [nf_tables]
[...]
[16302.231882] CPU: 0 PID: 100509 Comm: nft Tainted: G W 5.19.0-rc3+ #155
[...]
[16302.231887] RIP: 0010:nf_tables_chain_destroy+0x26/0x127 [nf_tables]
[16302.231899] Code: f3 fe ff ff 41 55 41 54 55 53 48 8b 6f 10 48 89 fb 48 c7 c7 82 96 d9 a0 8b 55 50 48 8b 75 58 e8 de f5 92 e0 83 7d 50 00 74 09 <0f> 0b 5b 5d 41 5c 41 5d c3 4c 8b 65 00 48 8b 7d 08 49 39 fc 74 05
[...]
[16302.231917] Call Trace:
[16302.231919] <TASK>
[16302.231921] __nf_tables_abort.cold+0x23/0x28 [nf_tables]
[16302.231934] nf_tables_abort+0x30/0x50 [nf_tables]
[16302.231946] nfnetlink_rcv_batch+0x41a/0x840 [nfnetlink]
[16302.231952] ? __nla_validate_parse+0x48/0x190
[16302.231959] nfnetlink_rcv+0x110/0x129 [nfnetlink]
[16302.231963] netlink_unicast+0x211/0x340
[16302.231969] netlink_sendmsg+0x21e/0x460
Add nft_set_pipapo_match_destroy() helper function to release the
elements in the lookup tables.
Stefano Brivio says: "We additionally look for elements pointers in the
cloned matching data if priv->dirty is set, because that means that
cloned data might point to additional elements we did not commit to the
working copy yet (such as the abort path case, but perhaps not limited
to it)."
Fixes:
3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Duoming Zhou [Tue, 5 Jul 2022 12:56:10 +0000 (20:56 +0800)]
net: rose: fix UAF bug caused by rose_t0timer_expiry
commit
148ca04518070910739dfc4eeda765057856403d upstream.
There are UAF bugs caused by rose_t0timer_expiry(). The
root cause is that del_timer() could not stop the timer
handler that is running and there is no synchronization.
One of the race conditions is shown below:
(thread 1) | (thread 2)
| rose_device_event
| rose_rt_device_down
| rose_remove_neigh
rose_t0timer_expiry | rose_stop_t0timer(rose_neigh)
... | del_timer(&neigh->t0timer)
| kfree(rose_neigh) //[1]FREE
neigh->dce_mode //[2]USE |
The rose_neigh is deallocated in position [1] and use in
position [2].
The crash trace triggered by POC is like below:
BUG: KASAN: use-after-free in expire_timers+0x144/0x320
Write of size 8 at addr
ffff888009b19658 by task swapper/0/0
...
Call Trace:
<IRQ>
dump_stack_lvl+0xbf/0xee
print_address_description+0x7b/0x440
print_report+0x101/0x230
? expire_timers+0x144/0x320
kasan_report+0xed/0x120
? expire_timers+0x144/0x320
expire_timers+0x144/0x320
__run_timers+0x3ff/0x4d0
run_timer_softirq+0x41/0x80
__do_softirq+0x233/0x544
...
This patch changes rose_stop_ftimer() and rose_stop_t0timer()
in rose_remove_neigh() to del_timer_sync() in order that the
timer handler could be finished before the resources such as
rose_neigh and so on are deallocated. As a result, the UAF
bugs could be mitigated.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20220705125610.77971-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Tue, 5 Jul 2022 12:53:51 +0000 (14:53 +0200)]
usbnet: fix memory leak in error case
commit
b55a21b764c1e182014630fa5486d717484ac58f upstream.
usbnet_write_cmd_async() mixed up which buffers
need to be freed in which error case.
v2: add Fixes tag
v3: fix uninitialized buf pointer
Fixes:
877bd862f32b8 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220705125351.17309-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Fri, 1 Jul 2022 12:47:25 +0000 (14:47 +0200)]
bpf: Fix insufficient bounds propagation from adjust_scalar_min_max_vals
commit
3844d153a41adea718202c10ae91dc96b37453b5 upstream.
Kuee reported a corner case where the tnum becomes constant after the call
to __reg_bound_offset(), but the register's bounds are not, that is, its
min bounds are still not equal to the register's max bounds.
This in turn allows to leak pointers through turning a pointer register as
is into an unknown scalar via adjust_ptr_min_max_vals().
Before:
func#0 @0
0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0))
1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0))
2: (87) r3 = -r3 ; R3_w=scalar()
3: (87) r3 = -r3 ; R3_w=scalar()
4: (47) r3 |= 32767 ; R3_w=scalar(smin=-
9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-
2147450881)
5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=
9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-
2147450881,u32_min=32767)
6: (95) exit
from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=
9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-
2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=
9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-
2147450881,u32_min=32767)
8: (95) exit
from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
9: (07) r3 += -32767 ; R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)) <--- [*]
10: (95) exit
What can be seen here is that R3=scalar(umin=32767,umax=32768,var_off=(0x7fff;
0x8000)) after the operation R3 += -32767 results in a 'malformed' constant, that
is, R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)). Intersecting with var_off has
not been done at that point via __update_reg_bounds(), which would have improved
the umax to be equal to umin.
Refactor the tnum <> min/max bounds information flow into a reg_bounds_sync()
helper and use it consistently everywhere. After the fix, bounds have been
corrected to R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) and thus the register
is regarded as a 'proper' constant scalar of 0.
After:
func#0 @0
0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0))
1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0))
2: (87) r3 = -r3 ; R3_w=scalar()
3: (87) r3 = -r3 ; R3_w=scalar()
4: (47) r3 |= 32767 ; R3_w=scalar(smin=-
9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-
2147450881)
5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=
9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-
2147450881,u32_min=32767)
6: (95) exit
from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=
9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-
2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=
9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-
2147450881,u32_min=32767)
8: (95) exit
from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0))
9: (07) r3 += -32767 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) <--- [*]
10: (95) exit
Fixes:
b03c9f9fdc37 ("bpf/verifier: track signed and unsigned min/max values")
Reported-by: Kuee K1r0a <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220701124727.11153-2-daniel@iogearbox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Fri, 1 Jul 2022 12:47:24 +0000 (14:47 +0200)]
bpf: Fix incorrect verifier simulation around jmp32's jeq/jne
commit
a12ca6277eca6aeeccf66e840c23a2b520e24c8f upstream.
Kuee reported a quirk in the jmp32's jeq/jne simulation, namely that the
register value does not match expectations for the fall-through path. For
example:
Before fix:
0: R1=ctx(off=0,imm=0) R10=fp0
0: (b7) r2 = 0 ; R2_w=P0
1: (b7) r6 = 563 ; R6_w=P563
2: (87) r2 = -r2 ; R2_w=Pscalar()
3: (87) r2 = -r2 ; R2_w=Pscalar()
4: (4c) w2 |= w6 ; R2_w=Pscalar(umin=563,umax=
4294967295,var_off=(0x233; 0xfffffdcc),s32_min=-
2147483085) R6_w=P563
5: (56) if w2 != 0x8 goto pc+1 ; R2_w=P571 <--- [*]
6: (95) exit
R0 !read_ok
After fix:
0: R1=ctx(off=0,imm=0) R10=fp0
0: (b7) r2 = 0 ; R2_w=P0
1: (b7) r6 = 563 ; R6_w=P563
2: (87) r2 = -r2 ; R2_w=Pscalar()
3: (87) r2 = -r2 ; R2_w=Pscalar()
4: (4c) w2 |= w6 ; R2_w=Pscalar(umin=563,umax=
4294967295,var_off=(0x233; 0xfffffdcc),s32_min=-
2147483085) R6_w=P563
5: (56) if w2 != 0x8 goto pc+1 ; R2_w=P8 <--- [*]
6: (95) exit
R0 !read_ok
As can be seen on line 5 for the branch fall-through path in R2 [*] is that
given condition w2 != 0x8 is false, verifier should conclude that r2 = 8 as
upper 32 bit are known to be zero. However, verifier incorrectly concludes
that r2 = 571 which is far off.
The problem is it only marks false{true}_reg as known in the switch for JE/NE
case, but at the end of the function, it uses {false,true}_{64,32}off to
update {false,true}_reg->var_off and they still hold the prior value of
{false,true}_reg->var_off before it got marked as known. The subsequent
__reg_combine_32_into_64() then propagates this old var_off and derives new
bounds. The information between min/max bounds on {false,true}_reg from
setting the register to known const combined with the {false,true}_reg->var_off
based on the old information then derives wrong register data.
Fix it by detangling the BPF_JEQ/BPF_JNE cases and updating relevant
{false,true}_{64,32}off tnums along with the register marking to known
constant.
Fixes:
3f50f132d840 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Kuee K1r0a <liulin063@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20220701124727.11153-1-daniel@iogearbox.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Kopp [Tue, 21 Dec 2021 22:24:52 +0000 (22:24 +0000)]
can: mcp251xfd: mcp251xfd_regmap_crc_read(): update workaround broken CRC on TBC register
commit
e3d4ee7d5f7f5256dfe89219afcc7a2d553b731f upstream.
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3caf ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.
Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes:
c7eb923c3caf ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Kopp [Tue, 21 Dec 2021 22:24:52 +0000 (22:24 +0000)]
can: mcp251xfd: mcp251xfd_regmap_crc_read(): improve workaround handling for mcp2517fd
commit
406cc9cdb3e8d644b15e8028948f091b82abdbca upstream.
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3caf ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
Measurements on the mcp2517fd show that the workaround is applicable
not only of the lowest byte is 0x00 or 0x80, but also if 3 least
significant bits are set.
Update check on 1st data byte and workaround description accordingly.
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes:
c7eb923c3caf ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Reported-by: Pavel Modilaynen <pavel.modilaynen@volvocars.com>
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Mon, 30 May 2022 17:30:28 +0000 (19:30 +0200)]
can: m_can: m_can_{read_fifo,echo_tx_event}(): shift timestamp to full 32 bits
commit
4c3333693f07313f5f0145a922f14a7d3c0f4f21 upstream.
In commit
1be37d3b0414 ("can: m_can: fix periph RX path: use
rx-offload to ensure skbs are sent from softirq context") the RX path
for peripheral devices was switched to RX-offload.
Received CAN frames are pushed to RX-offload together with a
timestamp. RX-offload is designed to handle overflows of the timestamp
correctly, if 32 bit timestamps are provided.
The timestamps of m_can core are only 16 bits wide. So this patch
shifts them to full 32 bit before passing them to RX-offload.
Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de
Fixes:
1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Kleine-Budde [Mon, 23 May 2022 15:18:33 +0000 (17:18 +0200)]
can: m_can: m_can_chip_config(): actually enable internal timestamping
commit
5b12933de4e76ec164031c18ce8e0904abf530d7 upstream.
In commit
df06fd678260 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.
The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.
Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes:
df06fd678260 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rhett Aultman [Sun, 3 Jul 2022 17:33:06 +0000 (19:33 +0200)]
can: gs_usb: gs_usb_open/close(): fix memory leak
commit
2bda24ef95c0311ab93bda00db40486acf30bd0a upstream.
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the
928150fad41b ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes:
d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liang He [Sun, 19 Jun 2022 07:02:57 +0000 (15:02 +0800)]
can: grcan: grcan_probe(): remove extra of_node_get()
commit
562fed945ea482833667f85496eeda766d511386 upstream.
In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.
Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes:
1e93ed26acf0 ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Hartkopp [Fri, 20 May 2022 18:32:39 +0000 (20:32 +0200)]
can: bcm: use call_rcu() instead of costly synchronize_rcu()
commit
f1b4e32aca0811aa011c76e5d6cf2fa19224b386 upstream.
In commit
d5f9023fa61e ("can: bcm: delay release of struct bcm_op
after synchronize_rcu()") Thadeu Lima de Souza Cascardo introduced two
synchronize_rcu() calls in bcm_release() (only once at socket close)
and in bcm_delete_rx_op() (called on removal of each single bcm_op).
Unfortunately this slow removal of the bcm_op's affects user space
applications like cansniffer where the modification of a filter
removes 2048 bcm_op's which blocks the cansniffer application for
40(!) seconds.
In commit
181d4447905d ("can: gw: use call_rcu() instead of costly
synchronize_rcu()") Eric Dumazet replaced the synchronize_rcu() calls
with several call_rcu()'s to safely remove the data structures after
the removal of CAN ID subscriptions with can_rx_unregister() calls.
This patch adopts Erics approach for the can-bcm which should be
applicable since the removal of tasklet_kill() in bcm_remove_op() and
the introduction of the HRTIMER_MODE_SOFT timer handling in Linux 5.4.
Fixes:
d5f9023fa61e ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") # >= 5.4
Link: https://lore.kernel.org/all/20220520183239.19111-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Cc: Eric Dumazet <edumazet@google.com>
Cc: Norbert Slusarek <nslusarek@gmx.net>
Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 5 Jul 2022 15:23:36 +0000 (17:23 +0200)]
ALSA: cs46xx: Fix missing snd_card_free() call at probe error
commit
c5e58c4545a69677d078b4c813b5d10d3481be9c upstream.
The previous cleanup with devres may lead to the incorrect release
orders at the probe error handling due to the devres's nature. Until
we register the card, snd_card_free() has to be called at first for
releasing the stuff properly when the driver tries to manage and
release the stuff via card->private_free().
This patch fixes it by calling snd_card_free() manually on the error
from the probe callback.
Fixes:
5bff69b3645d ("ALSA: cs46xx: Allocate resources with device-managed APIs")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Jan Engelhardt <jengelh@inai.de>
Link: https://lore.kernel.org/r/p2p1s96o-746-74p4-s95-61qo1p7782pn@vanv.qr
Link: https://lore.kernel.org/r/20220705152336.350-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tim Crawford [Fri, 24 Jun 2022 14:41:09 +0000 (08:41 -0600)]
ALSA: hda/realtek: Add quirk for Clevo L140PU
commit
11bea26929a1a3a9dd1a287b60c2f471701bf706 upstream.
Fixes headset detection on Clevo L140PU.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624144109.3957-1-tcrawford@system76.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 24 Jun 2022 10:11:32 +0000 (12:11 +0200)]
ALSA: usb-audio: Workarounds for Behringer UMC 204/404 HD
commit
ae8b1631561a3634cc09d0c62bbdd938eade05ec upstream.
Both Behringer UMC 202 HD and 404 HD need explicit quirks to enable
the implicit feedback mode and start the playback stream primarily.
The former seems fixing the stuttering and the latter is required for
a playback-only case.
Note that the "clock source 41 is not valid" error message still
appears even after this fix, but it should be only once at probe.
The reason of the error is still unknown, but this seems to be mostly
harmless as it's a one-off error and the driver retires the clock
setup and it succeeds afterwards.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220624101132.14528-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Po-Hsu Lin [Thu, 7 Jul 2022 09:42:07 +0000 (17:42 +0800)]
Revert "selftests/bpf: Add test for bpf_timer overwriting crash"
This reverts commit
b0028e1cc1faf2e5d88ad4065590aca90d650182 which is
commit
a7e75016a0753c24d6c995bc02501ae35368e333 upstream.
It will break the bpf self-tests build with:
progs/timer_crash.c:8:19: error: field has incomplete type 'struct bpf_timer'
struct bpf_timer timer;
^
/home/ubuntu/linux/tools/testing/selftests/bpf/tools/include/bpf/bpf_helper_defs.h:39:8:
note: forward declaration of 'struct bpf_timer'
struct bpf_timer;
^
1 error generated.
This test can only be built with 5.17 and newer kernels.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Shixin [Thu, 7 Jul 2022 02:09:38 +0000 (10:09 +0800)]
mm/filemap: fix UAF in find_lock_entries
Release refcount after xas_set to fix UAF which may cause panic like this:
page:
ffffea000491fa40 refcount:1 mapcount:0 mapping:
0000000000000000 index:0x1 pfn:0x1247e9
head:
ffffea000491fa00 order:3 compound_mapcount:0 compound_pincount:0
memcg:
ffff888104f91091
flags: 0x2fffff80010200(slab|head|node=0|zone=2|lastcpupid=0x1fffff)
...
page dumped because: VM_BUG_ON_PAGE(PageTail(page))
------------[ cut here ]------------
kernel BUG at include/linux/page-flags.h:632!
invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
CPU: 1 PID: 7642 Comm: sh Not tainted 5.15.51-dirty #26
...
Call Trace:
<TASK>
__invalidate_mapping_pages+0xe7/0x540
drop_pagecache_sb+0x159/0x320
iterate_supers+0x120/0x240
drop_caches_sysctl_handler+0xaa/0xe0
proc_sys_call_handler+0x2b4/0x480
new_sync_write+0x3d6/0x5c0
vfs_write+0x446/0x7a0
ksys_write+0x105/0x210
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f52b5733130
...
This problem has been fixed on mainline by patch
6b24ca4a1a8d ("mm: Use
multi-index entries in the page cache") since it deletes the related code.
Fixes:
5c211ba29deb ("mm: add and use find_lock_entries")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann Horn [Wed, 8 Jun 2022 18:22:05 +0000 (20:22 +0200)]
mm/slub: add missing TID updates on slab deactivation
commit
eeaa345e128515135ccb864c04482180c08e3259 upstream.
The fastpath in slab_alloc_node() assumes that c->slab is stable as long as
the TID stays the same. However, two places in __slab_alloc() currently
don't update the TID when deactivating the CPU slab.
If multiple operations race the right way, this could lead to an object
getting lost; or, in an even more unlikely situation, it could even lead to
an object being freed onto the wrong slab's freelist, messing up the
`inuse` counter and eventually causing a page to be freed to the page
allocator while it still contains slab objects.
(I haven't actually tested these cases though, this is just based on
looking at the code. Writing testcases for this stuff seems like it'd be
a pain...)
The race leading to state inconsistency is (all operations on the same CPU
and kmem_cache):
- task A: begin do_slab_free():
- read TID
- read pcpu freelist (==NULL)
- check `slab == c->slab` (true)
- [PREEMPT A->B]
- task B: begin slab_alloc_node():
- fastpath fails (`c->freelist` is NULL)
- enter __slab_alloc()
- slub_get_cpu_ptr() (disables preemption)
- enter ___slab_alloc()
- take local_lock_irqsave()
- read c->freelist as NULL
- get_freelist() returns NULL
- write `c->slab = NULL`
- drop local_unlock_irqrestore()
- goto new_slab
- slub_percpu_partial() is NULL
- get_partial() returns NULL
- slub_put_cpu_ptr() (enables preemption)
- [PREEMPT B->A]
- task A: finish do_slab_free():
- this_cpu_cmpxchg_double() succeeds()
- [CORRUPT STATE: c->slab==NULL, c->freelist!=NULL]
From there, the object on c->freelist will get lost if task B is allowed to
continue from here: It will proceed to the retry_load_slab label,
set c->slab, then jump to load_freelist, which clobbers c->freelist.
But if we instead continue as follows, we get worse corruption:
- task A: run __slab_free() on object from other struct slab:
- CPU_PARTIAL_FREE case (slab was on no list, is now on pcpu partial)
- task A: run slab_alloc_node() with NUMA node constraint:
- fastpath fails (c->slab is NULL)
- call __slab_alloc()
- slub_get_cpu_ptr() (disables preemption)
- enter ___slab_alloc()
- c->slab is NULL: goto new_slab
- slub_percpu_partial() is non-NULL
- set c->slab to slub_percpu_partial(c)
- [CORRUPT STATE: c->slab points to slab-1, c->freelist has objects
from slab-2]
- goto redo
- node_match() fails
- goto deactivate_slab
- existing c->freelist is passed into deactivate_slab()
- inuse count of slab-1 is decremented to account for object from
slab-2
At this point, the inuse count of slab-1 is 1 lower than it should be.
This means that if we free all allocated objects in slab-1 except for one,
SLUB will think that slab-1 is completely unused, and may free its page,
leading to use-after-free.
Fixes:
c17dda40a6a4e ("slub: Separate out kmem_cache_cpu processing from deactivate_slab")
Fixes:
03e404af26dc2 ("slub: fast release on full slab")
Cc: stable@vger.kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Acked-by: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Tested-by: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Link: https://lore.kernel.org/r/20220608182205.2945720-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 7 Jul 2022 15:53:35 +0000 (17:53 +0200)]
Linux 5.15.53
Link: https://lore.kernel.org/r/20220705115617.568350164@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yang Yingliang [Fri, 1 Jul 2022 07:41:53 +0000 (15:41 +0800)]
hwmon: (ibmaem) don't call platform_device_del() if platform_device_add() fails
[ Upstream commit
d0e51022a025ca5350fafb8e413a6fe5d4baf833 ]
If platform_device_add() fails, it no need to call platform_device_del(), split
platform_device_unregister() into platform_device_del/put(), so platform_device_put()
can be called separately.
Fixes:
8808a793f052 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eddie James [Tue, 28 Jun 2022 20:30:29 +0000 (15:30 -0500)]
hwmon: (occ) Prevent power cap command overwriting poll response
[ Upstream commit
1bbb2809040a1f9c7c53c9f06c21aa83275ed27b ]
Currently, the response to the power cap command overwrites the
first eight bytes of the poll response, since the commands use
the same buffer. This means that user's get the wrong data between
the time of sending the power cap and the next poll response update.
Fix this by specifying a different buffer for the power cap command
response.
Fixes:
5b5513b88002 ("hwmon: Add On-Chip Controller (OCC) hwmon driver")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20220628203029.51747-1-eajames@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eddie James [Wed, 21 Jul 2021 19:02:30 +0000 (14:02 -0500)]
hwmon: (occ) Remove sequence numbering and checksum calculation
[ Upstream commit
908dbf0242e21dd95c69a1b0935814cd1abfc134 ]
Checksumming of the request and sequence numbering is now done in the
OCC interface driver in order to keep unique sequence numbers. So
remove those in the hwmon driver. Also, add the command length to the
send_cmd function pointer, since the checksum must be placed in the
last two bytes of the command. The submit interface must receive the
exact size of the command - previously it could be rounded to the
nearest 8 bytes with no consequence.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210721190231.117185-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Carlos Llamas [Tue, 21 Jun 2022 20:39:21 +0000 (20:39 +0000)]
drm/fourcc: fix integer type usage in uapi header
[ Upstream commit
20b8264394b33adb1640a485a62a84bc1388b6a3 ]
Kernel uapi headers are supposed to use __[us]{8,16,32,64} types defined
by <linux/types.h> as opposed to 'uint32_t' and similar. See [1] for the
relevant discussion about this topic. In this particular case, the usage
of 'uint64_t' escaped headers_check as these macros are not being called
here. However, the following program triggers a compilation error:
#include <drm/drm_fourcc.h>
int main()
{
unsigned long x = AMD_FMT_MOD_CLEAR(RB);
return 0;
}
gcc error:
drm.c:5:27: error: ‘uint64_t’ undeclared (first use in this function)
5 | unsigned long x = AMD_FMT_MOD_CLEAR(RB);
| ^~~~~~~~~~~~~~~~~
This patch changes AMD_FMT_MOD_{SET,CLEAR} macros to use the correct
integer types, which fixes the above issue.
[1] https://lkml.org/lkml/2019/6/5/18
Fixes:
8ba16d599374 ("drm/fourcc: Add AMD DRM modifiers.")
Signed-off-by: Carlos Llamas <cmllamas@google.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Fri, 24 Jun 2022 11:23:39 +0000 (13:23 +0200)]
platform/x86: panasonic-laptop: filter out duplicate volume up/down/mute keypresses
[ Upstream commit
aacb455dfe01b7a24a792a2fbe7a04112ce8321d ]
On some Panasonic models the volume up/down/mute keypresses get
reported both through the Panasonic ACPI HKEY interface as well as
through the atkbd device.
Filter out the atkbd scan-codes for these to avoid reporting presses
twice.
Note normally we would leave the filtering of these to userspace by mapping
the scan-codes to KEY_UNKNOWN through /lib/udev/hwdb.d/60-keyboard.hwdb.
However in this case that would cause regressions since we were filtering
the Panasonic ACPI HKEY events before, so filter these in the kernel.
Fixes:
ed83c9171829 ("platform/x86: panasonic-laptop: Resolve hotkey double trigger bug")
Reported-and-tested-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Reported-and-tested-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220624112340.10130-7-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Fri, 24 Jun 2022 11:23:38 +0000 (13:23 +0200)]
platform/x86: panasonic-laptop: don't report duplicate brightness key-presses
[ Upstream commit
1f2c9de83a50447a2d7166f6273ab0c0e97cd68e ]
The brightness key-presses might also get reported by the ACPI video bus,
check for this and in this case don't report the presses to avoid reporting
2 presses for a single key-press.
Fixes:
ed83c9171829 ("platform/x86: panasonic-laptop: Resolve hotkey double trigger bug")
Reported-and-tested-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Reported-and-tested-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220624112340.10130-6-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Fri, 24 Jun 2022 11:23:37 +0000 (13:23 +0200)]
platform/x86: panasonic-laptop: revert "Resolve hotkey double trigger bug"
[ Upstream commit
83a5ddc3dc561c40d948b85553514aaba99123d8 ]
In hindsight blindly throwing away most of the key-press events is not
a good idea. So revert commit
ed83c9171829 ("platform/x86:
panasonic-laptop: Resolve hotkey double trigger bug").
Fixes:
ed83c9171829 ("platform/x86: panasonic-laptop: Resolve hotkey double trigger bug")
Reported-and-tested-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Reported-and-tested-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220624112340.10130-5-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Hans de Goede [Fri, 24 Jun 2022 11:23:36 +0000 (13:23 +0200)]
platform/x86: panasonic-laptop: sort includes alphabetically
[ Upstream commit
fe4326c8d18dc8a54affdc9ab269ad92dafef659 ]
Sort includes alphabetically, small cleanup patch in preparation of
further changes.
Fixes:
ed83c9171829 ("platform/x86: panasonic-laptop: Resolve hotkey double trigger bug")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220624112340.10130-4-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Stefan Seyfried [Fri, 24 Jun 2022 11:23:35 +0000 (13:23 +0200)]
platform/x86: panasonic-laptop: de-obfuscate button codes
[ Upstream commit
65a3e6c8d3f7c346813a05f3d76fc46b640d76d6 ]
In the definition of panasonic_keymap[] the key codes are given in
decimal, later checks are done with hexadecimal values, which does
not help in understanding the code.
Additionally use two helper variables to shorten the code and make
the logic more obvious.
Fixes:
ed83c9171829 ("platform/x86: panasonic-laptop: Resolve hotkey double trigger bug")
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220624112340.10130-3-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Liang He [Wed, 15 Jun 2022 09:48:07 +0000 (17:48 +0800)]
drivers: cpufreq: Add missing of_node_put() in qoriq-cpufreq.c
[ Upstream commit
4ff5a9b6d95f3524bf6d27147df497eb21968300 ]
In qoriq_cpufreq_probe(), of_find_matching_node() will return a
node pointer with refcount incremented. We should use of_node_put()
when it is not used anymore.
Fixes:
157f527639da ("cpufreq: qoriq: convert to a platform driver")
[ Viresh: Fixed Author's name in commit log ]
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Rob Clark [Fri, 24 Jun 2022 18:45:28 +0000 (11:45 -0700)]
drm/msm/gem: Fix error return on fence id alloc fail
[ Upstream commit
08de214138cdea438a0dfcb10d355a6650c6017c ]
This was a typo, we didn't actually want to return zero.
Fixes:
a61acbbe9cf8 ("drm/msm: Track "seqno" fences by idr")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491145/
Link: https://lore.kernel.org/r/20220624184528.4036837-1-robdclark@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
katrinzhou [Tue, 21 Jun 2022 12:49:26 +0000 (13:49 +0100)]
drm/i915/gem: add missing else
[ Upstream commit
9efdd519d001ee3e761f6ff80d5eb123387421c1 ]
Add missing else in set_proto_ctx_param() to fix coverity issue.
Addresses-Coverity: ("Unused value")
Fixes:
d4433c7600f7 ("drm/i915/gem: Use the proto-context to handle create parameters (v5)")
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: katrinzhou <katrinzhou@tencent.com>
[tursulin: fixup alignment]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220621124926.615884-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit
7482a65664c16cc88eb84d2b545a1fed887378a1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dan Carpenter [Thu, 23 Jun 2022 13:32:32 +0000 (16:32 +0300)]
net: fix IFF_TX_SKB_NO_LINEAR definition
[ Upstream commit
3b89b511ea0c705cc418440e2abf9d692a556d84 ]
The "1<<31" shift has a sign extension bug so IFF_TX_SKB_NO_LINEAR is
0xffffffff80000000 instead of 0x0000000080000000.
Fixes:
c2ff53d8049f ("net: Add priv_flags for allow tx skb without linear")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://lore.kernel.org/r/YrRrcGttfEVnf85Q@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Eddie James [Wed, 21 Jul 2021 19:02:29 +0000 (14:02 -0500)]
fsi: occ: Force sequence numbering per OCC
commit
62f79f3d0eb9f4c224bcc3c7f6fa758515a0a7fa upstream.
Set and increment the sequence number during the submit operation.
This prevents sequence number conflicts between different users of
the interface. A sequence number conflict may result in a user
getting an OCC response meant for a different command. Since the
sequence number is now modified, the checksum must be calculated and
set before submitting the command.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210721190231.117185-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 30 Jun 2022 09:55:42 +0000 (11:55 +0200)]
clocksource/drivers/ixp4xx: remove EXPORT_SYMBOL_GPL from ixp4xx_timer_setup()
ixp4xx_timer_setup is exported, and so can not be an __init function.
But it does not need to be exported as it is only called from one
in-kernel function, so just remove the EXPORT_SYMBOL_GPL() marking to
resolve the build warning.
This is fixed "properly" in commit
41929c9f628b
("clocksource/drivers/ixp4xx: Drop boardfile probe path") but that can
not be backported to older kernels as the reworking of the IXP4xx
codebase is not suitable for stable releases.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniele Palmas [Fri, 10 Dec 2021 09:57:22 +0000 (10:57 +0100)]
net: usb: qmi_wwan: add Telit 0x1070 composition
commit
94f2a444f28a649926c410eb9a38afb13a83ebe0 upstream.
Add the following Telit FN990 composition:
0x1070: tty, adb, rmnet, tty, tty, tty, tty
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211210095722.22269-1-dnlplm@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cc: Fabio Porcedda <fabio.porcedda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksandr Tyshchenko [Fri, 1 Jul 2022 07:57:42 +0000 (09:57 +0200)]
xen/arm: Fix race in RB-tree based P2M accounting
commit
b75cd218274e01d026dc5240e86fdeb44bbed0c8 upstream.
During the PV driver life cycle the mappings are added to
the RB-tree by set_foreign_p2m_mapping(), which is called from
gnttab_map_refs() and are removed by clear_foreign_p2m_mapping()
which is called from gnttab_unmap_refs(). As both functions end
up calling __set_phys_to_machine_multi() which updates the RB-tree,
this function can be called concurrently.
There is already a "p2m_lock" to protect against concurrent accesses,
but the problem is that the first read of "phys_to_mach.rb_node"
in __set_phys_to_machine_multi() is not covered by it, so this might
lead to the incorrect mappings update (removing in our case) in RB-tree.
In my environment the related issue happens rarely and only when
PV net backend is running, the xen_add_phys_to_mach_entry() claims
that it cannot add new pfn <-> mfn mapping to the tree since it is
already exists which results in a failure when mapping foreign pages.
But there might be other bad consequences related to the non-protected
root reads such use-after-free, etc.
While at it, also fix the similar usage in __pfn_to_mfn(), so
initialize "struct rb_node *n" with the "p2m_lock" held in both
functions to avoid possible bad consequences.
This is CVE-2022-33744 / XSA-406.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Beulich [Fri, 1 Jul 2022 07:57:19 +0000 (09:57 +0200)]
xen-netfront: restore __skb_queue_tail() positioning in xennet_get_responses()
commit
f63c2c2032c2e3caad9add3b82cc6e91c376fd26 upstream.
The commit referenced below moved the invocation past the "next" label,
without any explanation. In fact this allows misbehaving backends undue
control over the domain the frontend runs in, as earlier detected errors
require the skb to not be freed (it may be retained for later processing
via xennet_move_rx_slot(), or it may simply be unsafe to have it freed).
This is CVE-2022-33743 / XSA-405.
Fixes:
6c5aa6fc4def ("xen networking: add basic XDP support for xen-netfront")
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Pau Monne [Thu, 7 Apr 2022 11:04:24 +0000 (13:04 +0200)]
xen/blkfront: force data bouncing when backend is untrusted
commit
2400617da7eebf9167d71a46122828bc479d64c9 upstream.
Split the current bounce buffering logic used with persistent grants
into it's own option, and allow enabling it independently of
persistent grants. This allows to reuse the same code paths to
perform the bounce buffering required to avoid leaking contiguous data
in shared pages not part of the request fragments.
Reporting whether the backend is to be trusted can be done using a
module parameter, or from the xenstore frontend path as set by the
toolstack when adding the device.
This is CVE-2022-33742, part of XSA-403.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Pau Monne [Thu, 7 Apr 2022 10:20:06 +0000 (12:20 +0200)]
xen/netfront: force data bouncing when backend is untrusted
commit
4491001c2e0fa69efbb748c96ec96b100a5cdb7e upstream.
Bounce all data on the skbs to be transmitted into zeroed pages if the
backend is untrusted. This avoids leaking data present in the pages
shared with the backend but not part of the skb fragments. This
requires introducing a new helper in order to allocate skbs with a
size multiple of XEN_PAGE_SIZE so we don't leak contiguous data on the
granted pages.
Reporting whether the backend is to be trusted can be done using a
module parameter, or from the xenstore frontend path as set by the
toolstack when adding the device.
This is CVE-2022-33741, part of XSA-403.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Pau Monne [Wed, 6 Apr 2022 15:38:04 +0000 (17:38 +0200)]
xen/netfront: fix leaking data in shared pages
commit
307c8de2b02344805ebead3440d8feed28f2f010 upstream.
When allocating pages to be used for shared communication with the
backend always zero them, this avoids leaking unintended data present
on the pages.
This is CVE-2022-33740, part of XSA-403.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roger Pau Monne [Wed, 30 Mar 2022 07:03:48 +0000 (09:03 +0200)]
xen/blkfront: fix leaking data in shared pages
commit
2f446ffe9d737e9a844b97887919c4fda18246e7 upstream.
When allocating pages to be used for shared communication with the
backend always zero them, this avoids leaking unintended data present
on the pages.
This is CVE-2022-26365, part of XSA-403.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Thu, 3 Feb 2022 15:05:32 +0000 (10:05 -0500)]
selftests/rseq: Change type of rseq_offset to ptrdiff_t
commit
889c5d60fbcf332c8b6ab7054d45f2768914a375 upstream.
Just before the 2.35 release of glibc, the __rseq_offset userspace ABI
was changed from int to ptrdiff_t.
Adapt to this change in the kernel selftests.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://sourceware.org/pipermail/libc-alpha/2022-February/136024.html
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:53 +0000 (12:12 -0500)]
selftests/rseq: x86-32: use %gs segment selector for accessing rseq thread area
commit
127b6429d235ab7c358223bbfd8a8b8d8cc799b6 upstream.
Rather than use rseq_get_abi() and pass its result through a register to
the inline assembler, directly access the per-thread rseq area through a
memory reference combining the %gs segment selector, the constant offset
of the field in struct rseq, and the rseq_offset value (in a register).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-16-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:52 +0000 (12:12 -0500)]
selftests/rseq: x86-64: use %fs segment selector for accessing rseq thread area
commit
4e15bb766b6c6e963a4d33629034d0ec3b7637df upstream.
Rather than use rseq_get_abi() and pass its result through a register to
the inline assembler, directly access the per-thread rseq area through a
memory reference combining the %fs segment selector, the constant offset
of the field in struct rseq, and the rseq_offset value (in a register).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-15-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:51 +0000 (12:12 -0500)]
selftests/rseq: Fix: work-around asm goto compiler bugs
commit
b53823fb2ef854222853be164f3b1e815f315144 upstream.
gcc and clang each have their own compiler bugs with respect to asm
goto. Implement a work-around for compiler versions known to have those
bugs.
gcc prior to 4.8.2 miscompiles asm goto.
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670
gcc prior to 8.1.0 miscompiles asm goto at O1.
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=103908
clang prior to version 13.0.1 miscompiles asm goto at O2.
https://github.com/llvm/llvm-project/issues/52735
Work around these issues by adding a volatile inline asm with
memory clobber in the fallthrough after the asm goto and at each
label target. Emit this for all compilers in case other similar
issues are found in the future.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-14-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:50 +0000 (12:12 -0500)]
selftests/rseq: Remove arm/mips asm goto compiler work-around
commit
94c5cf2a0e193afffef8de48ddc42de6df7cac93 upstream.
The arm and mips work-around for asm goto size guess issues are not
properly documented, and lack reference to specific compiler versions,
upstream compiler bug tracker entry, and reproducer.
I can only find a loosely documented patch in my original LKML rseq post
refering to gcc < 7 on ARM, but it does not appear to be sufficient to
track the exact issue. Also, I am not sure MIPS really has the same
limitation.
Therefore, remove the work-around until we can properly document this.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/lkml/20171121141900.18471-17-mathieu.desnoyers@efficios.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:49 +0000 (12:12 -0500)]
selftests/rseq: Fix warnings about #if checks of undefined tokens
commit
d7ed99ade3e62b755584eea07b4e499e79240527 upstream.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-12-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:48 +0000 (12:12 -0500)]
selftests/rseq: Fix ppc32 offsets by using long rather than off_t
commit
26dc8a6d8e11552f3b797b5aafe01071ca32d692 upstream.
The semantic of off_t is for file offsets. We mean to use it as an
offset from a pointer. We really expect it to fit in a single register,
and not use a 64-bit type on 32-bit architectures.
Fix runtime issues on ppc32 where the offset is always 0 due to
inconsistency between the argument type (off_t -> 64-bit) and type
expected by the inline assembler (32-bit).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-11-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:47 +0000 (12:12 -0500)]
selftests/rseq: Fix ppc32 missing instruction selection "u" and "x" for load/store
commit
de6b52a21420a18dc8a36438d581efd1313d5fe3 upstream.
Building the rseq basic test with
gcc version 5.4.0
20160609 (Ubuntu 5.4.0-6ubuntu1~16.04.12)
Target: powerpc-linux-gnu
leads to these errors:
/tmp/ccieEWxU.s: Assembler messages:
/tmp/ccieEWxU.s:118: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:118: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:121: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:121: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:626: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:626: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:629: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:629: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:735: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:735: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:738: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:738: Error: junk at end of line: `,8'
/tmp/ccieEWxU.s:741: Error: syntax error; found `,', expected `('
/tmp/ccieEWxU.s:741: Error: junk at end of line: `,8'
Makefile:581: recipe for target 'basic_percpu_ops_test.o' failed
Based on discussion with Linux powerpc maintainers and review of
the use of the "m" operand in powerpc kernel code, add the missing
%Un%Xn (where n is operand number) to the lwz, stw, ld, and std
instructions when used with "m" operands.
Using "WORD" to mean either a 32-bit or 64-bit type depending on
the architecture is misleading. The term "WORD" really means a
32-bit type in both 32-bit and 64-bit powerpc assembler. The intent
here is to wrap load/store to intptr_t into common macros for both
32-bit and 64-bit.
Rename the macros with a RSEQ_ prefix, and use the terms "INT"
for always 32-bit type, and "LONG" for architecture bitness-sized
type.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-10-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:46 +0000 (12:12 -0500)]
selftests/rseq: Fix ppc32: wrong rseq_cs 32-bit field pointer on big endian
commit
24d1136a29da5953de5c0cbc6c83eb62a1e0bf14 upstream.
ppc32 incorrectly uses padding as rseq_cs pointer field. Fix this by
using the rseq_cs.arch.ptr field.
Use this field across all architectures.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-9-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:45 +0000 (12:12 -0500)]
selftests/rseq: Uplift rseq selftests for compatibility with glibc-2.35
commit
233e667e1ae3e348686bd9dd0172e62a09d852e1 upstream.
glibc-2.35 (upcoming release date 2022-02-01) exposes the rseq per-thread
data in the TCB, accessible at an offset from the thread pointer, rather
than through an actual Thread-Local Storage (TLS) variable, as the
Linux kernel selftests initially expected.
The __rseq_abi TLS and glibc-2.35's ABI for per-thread data cannot
actively coexist in a process, because the kernel supports only a single
rseq registration per thread.
Here is the scheme introduced to ensure selftests can work both with an
older glibc and with glibc-2.35+:
- librseq exposes its own "rseq_offset, rseq_size, rseq_flags" ABI.
- librseq queries for glibc rseq ABI (__rseq_offset, __rseq_size,
__rseq_flags) using dlsym() in a librseq library constructor. If those
are found, copy their values into rseq_offset, rseq_size, and
rseq_flags.
- Else, if those glibc symbols are not found, handle rseq registration
from librseq and use its own IE-model TLS to implement the rseq ABI
per-thread storage.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-8-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:44 +0000 (12:12 -0500)]
selftests/rseq: Introduce thread pointer getters
commit
886ddfba933f5ce9d76c278165d834d114ba4ffc upstream.
This is done in preparation for the selftest uplift to become compatible
with glibc-2.35.
glibc-2.35 exposes the rseq per-thread data in the TCB, accessible
at an offset from the thread pointer.
The toolchains do not implement accessing the thread pointer on all
architectures. Provide thread pointer getters for ppc and x86 which
lack (or lacked until recently) toolchain support.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-7-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:43 +0000 (12:12 -0500)]
selftests/rseq: Introduce rseq_get_abi() helper
commit
e546cd48ccc456074ddb8920732aef4af65d7ca7 upstream.
This is done in preparation for the selftest uplift to become compatible
with glibc-2.35.
glibc-2.35 exposes the rseq per-thread data in the TCB, accessible
at an offset from the thread pointer, rather than through an actual
Thread-Local Storage (TLS) variable, as the kernel selftests initially
expected.
Introduce a rseq_get_abi() helper, initially using the __rseq_abi
TLS variable, in preparation for changing this userspace ABI for one
which is compatible with glibc-2.35.
Note that the __rseq_abi TLS and glibc-2.35's ABI for per-thread data
cannot actively coexist in a process, because the kernel supports only
a single rseq registration per thread.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-6-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:42 +0000 (12:12 -0500)]
selftests/rseq: Remove volatile from __rseq_abi
commit
94b80a19ebfe347a01301d750040a61c38200e2b upstream.
This is done in preparation for the selftest uplift to become compatible
with glibc-2.35.
All accesses to the __rseq_abi fields are volatile, but remove the
volatile from the TLS variable declaration, otherwise we are stuck with
volatile for the upcoming rseq_get_abi() helper.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-5-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:41 +0000 (12:12 -0500)]
selftests/rseq: Remove useless assignment to cpu variable
commit
930378d056eac2c96407b02aafe4938d0ac9cc37 upstream.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-4-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Desnoyers [Mon, 24 Jan 2022 17:12:39 +0000 (12:12 -0500)]
selftests/rseq: introduce own copy of rseq uapi header
commit
5c105d55a9dc9e01535116ccfc26e703168a574f upstream.
The Linux kernel rseq uapi header has a broken layout for the
rseq_cs.ptr field on 32-bit little endian architectures. The entire
rseq_cs.ptr field is planned for removal, leaving only the 64-bit
rseq_cs.ptr64 field available.
Both glibc and librseq use their own copy of the Linux kernel uapi
header, where they introduce proper union fields to access to the 32-bit
low order bits of the rseq_cs pointer on 32-bit architectures.
Introduce a copy of the Linux kernel uapi headers in the Linux kernel
selftests.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20220124171253.22072-2-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuah Khan [Thu, 9 Dec 2021 23:19:09 +0000 (16:19 -0700)]
selftests/rseq: remove ARRAY_SIZE define from individual tests
commit
07ad4f7629d4802ff0d962b0ac23ea6445964e2a upstream.
ARRAY_SIZE is defined in several selftests. Remove definitions from
individual test files and include header file for the define instead.
ARRAY_SIZE define is added in a separate patch to prepare for this
change.
Remove ARRAY_SIZE from rseq tests and pickup the one defined in
kselftest.h.
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kumar Kartikeya Dwivedi [Fri, 14 Jan 2022 16:39:51 +0000 (22:09 +0530)]
selftests/bpf: Add test_verifier support to fixup kfunc call insns
commit
0201b80772ac2b712bbbfe783cdb731fdfb4247e upstream.
This allows us to add tests (esp. negative tests) where we only want to
ensure the program doesn't pass through the verifier, and also verify
the error. The next commit will add the tests making use of this.
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20220114163953.1455836-9-memxor@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
[PHLin: backport due to lack of fixup_map_timer]
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Thu, 23 Jun 2022 05:04:36 +0000 (05:04 +0000)]
tcp: add a missing nf_reset_ct() in 3WHS handling
commit
6f0012e35160cd08a53e46e3b3bbf724b92dfe68 upstream.
When the third packet of 3WHS connection establishment
contains payload, it is added into socket receive queue
without the XFRM check and the drop of connection tracking
context.
This means that if the data is left unread in the socket
receive queue, conntrack module can not be unloaded.
As most applications usually reads the incoming data
immediately after accept(), bug has been hiding for
quite a long time.
Commit
68822bdf76f1 ("net: generalize skb freeing
deferral to per-cpu lists") exposed this bug because
even if the application reads this data, the skb
with nfct state could stay in a per-cpu cache for
an arbitrary time, if said cpu no longer process RX softirqs.
Many thanks to Ilya Maximets for reporting this issue,
and for testing various patches:
https://lore.kernel.org/netdev/
20220619003919.394622-1-i.maximets@ovn.org/
Note that I also added a missing xfrm4_policy_check() call,
although this is probably not a big issue, as the SYN
packet should have been dropped earlier.
Fixes:
b59c270104f0 ("[NETFILTER]: Keep conntrack reference until IPsec policy checks are done")
Reported-by: Ilya Maximets <i.maximets@ovn.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Tested-by: Ilya Maximets <i.maximets@ovn.org>
Reviewed-by: Ilya Maximets <i.maximets@ovn.org>
Link: https://lore.kernel.org/r/20220623050436.1290307-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leah Rumancik [Thu, 30 Jun 2022 20:52:28 +0000 (13:52 -0700)]
MAINTAINERS: add Leah as xfs maintainer for 5.15.y
Update MAINTAINERS for xfs in an effort to help direct bots/questions
about xfs in 5.15.y.
Note: 5.10.y and 5.4.y will have different updates to their
respective MAINTAINERS files for this effort.
Suggested-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Leah Rumancik <leah.rumancik@gmail.com>
Reviewed-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jakub Kicinski [Wed, 29 Jun 2022 18:19:10 +0000 (11:19 -0700)]
net: tun: avoid disabling NAPI twice
commit
ff1fa2081d173b01cebe2fbf0a2d0f1cee9ce4b5 upstream.
Eric reports that syzbot made short work out of my speculative
fix. Indeed when queue gets detached its tfile->tun remains,
so we would try to stop NAPI twice with a detach(), close()
sequence.
Alternative fix would be to move tun_napi_disable() to
tun_detach_all() and let the NAPI run after the queue
has been detached.
Fixes:
a8fc8cb5692a ("net: tun: stop NAPI when detaching queues")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220629181911.372047-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petr Machata [Wed, 29 Jun 2022 07:02:05 +0000 (10:02 +0300)]
mlxsw: spectrum_router: Fix rollback in tunnel next hop init
commit
665030fd0c1ed9f505932e6e73e7a2c788787a0a upstream.
In mlxsw_sp_nexthop6_init(), a next hop is always added to the router
linked list, and mlxsw_sp_nexthop_type_init() is invoked afterwards. When
that function results in an error, the next hop will not have been removed
from the linked list. As the error is propagated upwards and the caller
frees the next hop object, the linked list ends up holding an invalid
object.
A similar issue comes up with mlxsw_sp_nexthop4_init(), where rollback
block does exist, however does not include the linked list removal.
Both IPv6 and IPv4 next hops have a similar issue with next-hop counter
rollbacks. As these were introduced in the same patchset as the next hop
linked list, include the cleanup in this patch.
Fixes:
dbe4598c1e92 ("mlxsw: spectrum_router: Keep nexthops in a linked list")
Fixes:
a5390278a5eb ("mlxsw: spectrum: Add support for setting counters on nexthops")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220629070205.803952-1-idosch@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 28 Jun 2022 12:12:48 +0000 (12:12 +0000)]
ipv6: fix lockdep splat in in6_dump_addrs()
commit
4e43e64d0f1332fcc503babad4dc31aead7131ca upstream.
As reported by syzbot, we should not use rcu_dereference()
when rcu_read_lock() is not held.
WARNING: suspicious RCU usage
5.19.0-rc2-syzkaller #0 Not tainted
net/ipv6/addrconf.c:5175 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
1 lock held by syz-executor326/3617:
#0:
ffffffff8d5848e8 (rtnl_mutex){+.+.}-{3:3}, at: netlink_dump+0xae/0xc20 net/netlink/af_netlink.c:2223
stack backtrace:
CPU: 0 PID: 3617 Comm: syz-executor326 Not tainted 5.19.0-rc2-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
in6_dump_addrs+0x12d1/0x1790 net/ipv6/addrconf.c:5175
inet6_dump_addr+0x9c1/0xb50 net/ipv6/addrconf.c:5300
netlink_dump+0x541/0xc20 net/netlink/af_netlink.c:2275
__netlink_dump_start+0x647/0x900 net/netlink/af_netlink.c:2380
netlink_dump_start include/linux/netlink.h:245 [inline]
rtnetlink_rcv_msg+0x73e/0xc90 net/core/rtnetlink.c:6046
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2492
___sys_sendmsg+0xf3/0x170 net/socket.c:2546
__sys_sendmsg net/socket.c:2575 [inline]
__do_sys_sendmsg net/socket.c:2584 [inline]
__se_sys_sendmsg net/socket.c:2582 [inline]
__x64_sys_sendmsg+0x132/0x220 net/socket.c:2582
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
Fixes:
88e2ca308094 ("mld: convert ifmcaddr6 to RCU")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20220628121248.858695-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
katrinzhou [Tue, 28 Jun 2022 03:50:30 +0000 (11:50 +0800)]
ipv6/sit: fix ipip6_tunnel_get_prl return value
commit
adabdd8f6acabc0c3fdbba2e7f5a2edd9c5ef22d upstream.
When kcalloc fails, ipip6_tunnel_get_prl() should return -ENOMEM.
Move the position of label "out" to return correctly.
Addresses-Coverity: ("Unused value")
Fixes:
300aaeeaab5f ("[IPV6] SIT: Add SIOCGETPRL ioctl to get/dump PRL.")
Signed-off-by: katrinzhou <katrinzhou@tencent.com>
Reviewed-by: Eric Dumazet<edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220628035030.1039171-1-zys.zljxml@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 24 Jun 2022 15:30:20 +0000 (15:30 +0000)]
tunnels: do not assume mac header is set in skb_tunnel_check_pmtu()
commit
853a7614880231747040cada91d2b8d2e995c51a upstream.
Recently added debug in commit
f9aefd6b2aa3 ("net: warn if mac header
was not set") caught a bug in skb_tunnel_check_pmtu(), as shown
in this syzbot report [1].
In ndo_start_xmit() paths, there is really no need to use skb->mac_header,
because skb->data is supposed to point at it.
[1] WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_mac_header_len include/linux/skbuff.h:2784 [inline]
WARNING: CPU: 1 PID: 8604 at include/linux/skbuff.h:2784 skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413
Modules linked in:
CPU: 1 PID: 8604 Comm: syz-executor.3 Not tainted 5.19.0-rc2-syzkaller-00443-g8720bd951b8e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:skb_mac_header_len include/linux/skbuff.h:2784 [inline]
RIP: 0010:skb_tunnel_check_pmtu+0x5de/0x2f90 net/ipv4/ip_tunnel_core.c:413
Code: 00 00 00 00 fc ff df 4c 89 fa 48 c1 ea 03 80 3c 02 00 0f 84 b9 fe ff ff 4c 89 ff e8 7c 0f d7 f9 e9 ac fe ff ff e8 c2 13 8a f9 <0f> 0b e9 28 fc ff ff e8 b6 13 8a f9 48 8b 54 24 70 48 b8 00 00 00
RSP: 0018:
ffffc90002e4f520 EFLAGS:
00010212
RAX:
0000000000000324 RBX:
ffff88804d5fd500 RCX:
ffffc90005b52000
RDX:
0000000000040000 RSI:
ffffffff87f05e3e RDI:
0000000000000003
RBP:
ffffc90002e4f650 R08:
0000000000000003 R09:
000000000000ffff
R10:
000000000000ffff R11:
0000000000000000 R12:
000000000000ffff
R13:
0000000000000000 R14:
000000000000ffcd R15:
000000000000001f
FS:
00007f3babba9700(0000) GS:
ffff8880b9b00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020000080 CR3:
0000000075319000 CR4:
00000000003506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
geneve_xmit_skb drivers/net/geneve.c:927 [inline]
geneve_xmit+0xcf8/0x35d0 drivers/net/geneve.c:1107
__netdev_start_xmit include/linux/netdevice.h:4805 [inline]
netdev_start_xmit include/linux/netdevice.h:4819 [inline]
__dev_direct_xmit+0x500/0x730 net/core/dev.c:4309
dev_direct_xmit include/linux/netdevice.h:3007 [inline]
packet_direct_xmit+0x1b8/0x2c0 net/packet/af_packet.c:282
packet_snd net/packet/af_packet.c:3073 [inline]
packet_sendmsg+0x21f4/0x55d0 net/packet/af_packet.c:3104
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2489
___sys_sendmsg+0xf3/0x170 net/socket.c:2543
__sys_sendmsg net/socket.c:2572 [inline]
__do_sys_sendmsg net/socket.c:2581 [inline]
__se_sys_sendmsg net/socket.c:2579 [inline]
__x64_sys_sendmsg+0x132/0x220 net/socket.c:2579
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f3baaa89109
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007f3babba9168 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
00007f3baab9bf60 RCX:
00007f3baaa89109
RDX:
0000000000000000 RSI:
0000000020000a00 RDI:
0000000000000003
RBP:
00007f3baaae305d R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00007ffe74f2543f R14:
00007f3babba9300 R15:
0000000000022000
</TASK>
Fixes:
4cb47a8644cc ("tunnels: PMTU discovery support for directly bridged IP packets")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Fri, 24 Jun 2022 11:23:34 +0000 (13:23 +0200)]
ACPI: video: Change how we determine if brightness key-presses are handled
commit
3a0cf7ab8df3878a7e2f3d29275b785cf4e7afb6 upstream.
Some systems have an ACPI video bus but not ACPI video devices with
backlight capability. On these devices brightness key-presses are
(logically) not reported through the ACPI video bus.
Change how acpi_video_handles_brightness_key_presses() determines if
brightness key-presses are handled by the ACPI video driver to avoid
vendor specific drivers/platform/x86 drivers filtering out their
brightness key-presses even though they are the only ones reporting
these presses.
Fixes:
ed83c9171829 ("platform/x86: panasonic-laptop: Resolve hotkey double trigger bug")
Reported-and-tested-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Reported-and-tested-by: Kenneth Chan <kenneth.t.chan@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220624112340.10130-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jens Axboe [Thu, 30 Jun 2022 20:42:05 +0000 (14:42 -0600)]
io_uring: ensure that send/sendmsg and recv/recvmsg check sqe->ioprio
commit
73911426aaaadbae54fa72359b33a7b6a56947db upstream.
All other opcodes correctly check if this is set and -EINVAL if it is
and they don't support that field, for some reason the these were
forgotten.
This was unified a bit differently in the upstream tree, but had the
same effect as making sure we error on this field. Rather than have
a painful backport of the upstream commit, just fixup the mentioned
opcodes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tong Zhang [Mon, 27 Jun 2022 04:33:48 +0000 (21:33 -0700)]
epic100: fix use after free on rmmod
commit
8ee9d82cd0a45e7d050ade598c9f33032a0f2891 upstream.
epic_close() calls epic_rx() and uses dma buffer, but in epic_remove_one()
we already freed the dma buffer. To fix this issue, reorder function calls
like in the .probe function.
BUG: KASAN: use-after-free in epic_rx+0xa6/0x7e0 [epic100]
Call Trace:
epic_rx+0xa6/0x7e0 [epic100]
epic_close+0xec/0x2f0 [epic100]
unregister_netdev+0x18/0x20
epic_remove_one+0xaa/0xf0 [epic100]
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Yilun Wu <yiluwu@cs.stonybrook.edu>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Link: https://lore.kernel.org/r/20220627043351.25615-1-ztong0001@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xin Long [Fri, 24 Jun 2022 16:24:31 +0000 (12:24 -0400)]
tipc: move bc link creation back to tipc_node_create
commit
cb8092d70a6f5f01ec1490fce4d35efed3ed996c upstream.
Shuang Li reported a NULL pointer dereference crash:
[] BUG: kernel NULL pointer dereference, address:
0000000000000068
[] RIP: 0010:tipc_link_is_up+0x5/0x10 [tipc]
[] Call Trace:
[] <IRQ>
[] tipc_bcast_rcv+0xa2/0x190 [tipc]
[] tipc_node_bc_rcv+0x8b/0x200 [tipc]
[] tipc_rcv+0x3af/0x5b0 [tipc]
[] tipc_udp_recv+0xc7/0x1e0 [tipc]
It was caused by the 'l' passed into tipc_bcast_rcv() is NULL. When it
creates a node in tipc_node_check_dest(), after inserting the new node
into hashtable in tipc_node_create(), it creates the bc link. However,
there is a gap between this insert and bc link creation, a bc packet
may come in and get the node from the hashtable then try to dereference
its bc link, which is NULL.
This patch is to fix it by moving the bc link creation before inserting
into the hashtable.
Note that for a preliminary node becoming "real", the bc link creation
should also be called before it's rehashed, as we don't create it for
preliminary nodes.
Fixes:
4cbf8ac2fe5a ("tipc: enable creating a "preliminary" node")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Walle [Mon, 27 Jun 2022 17:06:42 +0000 (19:06 +0200)]
NFC: nxp-nci: Don't issue a zero length i2c_master_read()
commit
eddd95b9423946aaacb55cac6a9b2cea8ab944fc upstream.
There are packets which doesn't have a payload. In that case, the second
i2c_master_read() will have a zero length. But because the NFC
controller doesn't have any data left, it will NACK the I2C read and
-ENXIO will be returned. In case there is no payload, just skip the
second i2c master read.
Fixes:
6be88670fc59 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Mon, 27 Jun 2022 12:40:48 +0000 (14:40 +0200)]
nfc: nfcmrvl: Fix irq_of_parse_and_map() return value
commit
5a478a653b4cca148d5c89832f007ec0809d7e6d upstream.
The irq_of_parse_and_map() returns 0 on failure, not a negative ERRNO.
Reported-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Fixes:
caf6e49bf6d0 ("NFC: nfcmrvl: add spi driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220627124048.296253-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aneesh Kumar K.V [Wed, 29 Jun 2022 05:09:25 +0000 (10:39 +0530)]
powerpc/memhotplug: Add add_pages override for PPC
commit
ac790d09885d36143076e7e02825c541e8eee899 upstream.
With commit
ffa0b64e3be5 ("powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit")
the kernel now validate the addr against high_memory value. This results
in the below BUG_ON with dax pfns.
[ 635.798741][T26531] kernel BUG at mm/page_alloc.c:5521!
1:mon> e
cpu 0x1: Vector: 700 (Program Check) at [
c000000007287630]
pc:
c00000000055ed48: free_pages.part.0+0x48/0x110
lr:
c00000000053ca70: tlb_finish_mmu+0x80/0xd0
sp:
c0000000072878d0
msr:
800000000282b033
current = 0xc00000000afabe00
paca = 0xc00000037ffff300 irqmask: 0x03 irq_happened: 0x05
pid = 26531, comm = 50-landscape-sy
kernel BUG at :5521!
Linux version 5.19.0-rc3-14659-g4ec05be7c2e1 (kvaneesh@ltc-boston8) (gcc (Ubuntu 9.4.0-1ubuntu1~20.04.1) 9.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #625 SMP Thu Jun 23 00:35:43 CDT 2022
1:mon> t
[link register ]
c00000000053ca70 tlb_finish_mmu+0x80/0xd0
[
c0000000072878d0]
c00000000053ca54 tlb_finish_mmu+0x64/0xd0 (unreliable)
[
c000000007287900]
c000000000539424 exit_mmap+0xe4/0x2a0
[
c0000000072879e0]
c00000000019fc1c mmput+0xcc/0x210
[
c000000007287a20]
c000000000629230 begin_new_exec+0x5e0/0xf40
[
c000000007287ae0]
c00000000070b3cc load_elf_binary+0x3ac/0x1e00
[
c000000007287c10]
c000000000627af0 bprm_execve+0x3b0/0xaf0
[
c000000007287cd0]
c000000000628414 do_execveat_common.isra.0+0x1e4/0x310
[
c000000007287d80]
c00000000062858c sys_execve+0x4c/0x60
[
c000000007287db0]
c00000000002c1b0 system_call_exception+0x160/0x2c0
[
c000000007287e10]
c00000000000c53c system_call_common+0xec/0x250
The fix is to make sure we update high_memory on memory hotplug.
This is similar to what x86 does in commit
3072e413e305 ("mm/memory_hotplug: introduce add_pages")
Fixes:
ffa0b64e3be5 ("powerpc: Fix virt_addr_valid() for 64-bit Book3E & 32-bit")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Reviewed-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220629050925.31447-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yevhen Orlov [Wed, 29 Jun 2022 01:29:14 +0000 (04:29 +0300)]
net: bonding: fix use-after-free after 802.3ad slave unbind
commit
050133e1aa2cb49bb17be847d48a4431598ef562 upstream.
commit
0622cab0341c ("bonding: fix 802.3ad aggregator reselection"),
resolve case, when there is several aggregation groups in the same bond.
bond_3ad_unbind_slave will invalidate (clear) aggregator when
__agg_active_ports return zero. So, ad_clear_agg can be executed even, when
num_of_ports!=0. Than bond_3ad_unbind_slave can be executed again for,
previously cleared aggregator. NOTE: at this time bond_3ad_unbind_slave
will not update slave ports list, because lag_ports==NULL. So, here we
got slave ports, pointing to freed aggregator memory.
Fix with checking actual number of ports in group (as was before
commit
0622cab0341c ("bonding: fix 802.3ad aggregator reselection") ),
before ad_clear_agg().
The KASAN logs are as follows:
[ 767.617392] ==================================================================
[ 767.630776] BUG: KASAN: use-after-free in bond_3ad_state_machine_handler+0x13dc/0x1470
[ 767.638764] Read of size 2 at addr
ffff00011ba9d430 by task kworker/u8:7/767
[ 767.647361] CPU: 3 PID: 767 Comm: kworker/u8:7 Tainted: G O 5.15.11 #15
[ 767.655329] Hardware name: DNI AmazonGo1 A7040 board (DT)
[ 767.660760] Workqueue: lacp_1 bond_3ad_state_machine_handler
[ 767.666468] Call trace:
[ 767.668930] dump_backtrace+0x0/0x2d0
[ 767.672625] show_stack+0x24/0x30
[ 767.675965] dump_stack_lvl+0x68/0x84
[ 767.679659] print_address_description.constprop.0+0x74/0x2b8
[ 767.685451] kasan_report+0x1f0/0x260
[ 767.689148] __asan_load2+0x94/0xd0
[ 767.692667] bond_3ad_state_machine_handler+0x13dc/0x1470
Fixes:
0622cab0341c ("bonding: fix 802.3ad aggregator reselection")
Co-developed-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220629012914.361-1-yevhen.orlov@plvision.eu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksij Rempel [Tue, 28 Jun 2022 11:43:49 +0000 (13:43 +0200)]
net: phy: ax88772a: fix lost pause advertisement configuration
commit
fa152f626b24ec2ca3489100d8c5c0a0bce4e2ef upstream.
In case of asix_ax88772a_link_change_notify() workaround, we run soft
reset which will automatically clear MII_ADVERTISE configuration. The
PHYlib framework do not know about changed configuration state of the
PHY, so we need use phy_init_hw() to reinit PHY configuration.
Fixes:
dde258469257 ("net: usb/phy: asix: add support for ax88772A/C PHYs")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220628114349.3929928-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Mon, 27 Jun 2022 10:28:13 +0000 (10:28 +0000)]
net: bonding: fix possible NULL deref in rlb code
commit
ab84db251c04d38b8dc7ee86e13d4050bedb1c88 upstream.
syzbot has two reports involving the same root cause.
bond_alb_initialize() must not set bond->alb_info.rlb_enabled
if a memory allocation error is detected.
Report 1:
general protection fault, probably for non-canonical address 0xdffffc0000000002: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
CPU: 0 PID: 12276 Comm: kworker/u4:10 Not tainted 5.19.0-rc3-syzkaller-00132-g3b89b511ea0c #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: netns cleanup_net
RIP: 0010:rlb_clear_slave+0x10e/0x690 drivers/net/bonding/bond_alb.c:393
Code: 8e fc 83 fb ff 0f 84 74 02 00 00 e8 cc 2a 8e fc 48 8b 44 24 08 89 dd 48 c1 e5 06 4c 8d 34 28 49 8d 7e 14 48 89 f8 48 c1 e8 03 <42> 0f b6 14 20 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85
RSP: 0018:
ffffc90018a8f678 EFLAGS:
00010203
RAX:
0000000000000002 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
ffff88803375bb00 RSI:
ffffffff84ec4ac4 RDI:
0000000000000014
RBP:
0000000000000000 R08:
0000000000000005 R09:
00000000ffffffff
R10:
0000000000000000 R11:
0000000000000000 R12:
dffffc0000000000
R13:
ffff8880ac889000 R14:
0000000000000000 R15:
ffff88815a668c80
FS:
0000000000000000(0000) GS:
ffff8880b9a00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00005597077e10b0 CR3:
0000000026668000 CR4:
00000000003506f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
bond_alb_deinit_slave+0x43c/0x6b0 drivers/net/bonding/bond_alb.c:1663
__bond_release_one.cold+0x383/0xd53 drivers/net/bonding/bond_main.c:2370
bond_slave_netdev_event drivers/net/bonding/bond_main.c:3778 [inline]
bond_netdev_event+0x993/0xad0 drivers/net/bonding/bond_main.c:3889
notifier_call_chain+0xb5/0x200 kernel/notifier.c:87
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1945
call_netdevice_notifiers_extack net/core/dev.c:1983 [inline]
call_netdevice_notifiers net/core/dev.c:1997 [inline]
unregister_netdevice_many+0x948/0x18b0 net/core/dev.c:10839
default_device_exit_batch+0x449/0x590 net/core/dev.c:11333
ops_exit_list+0x125/0x170 net/core/net_namespace.c:167
cleanup_net+0x4ea/0xb00 net/core/net_namespace.c:594
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:302
</TASK>
Report 2:
general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
CPU: 1 PID: 5206 Comm: syz-executor.1 Not tainted 5.18.0-syzkaller-12108-g58f9d52ff689 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:rlb_req_update_slave_clients+0x109/0x2f0 drivers/net/bonding/bond_alb.c:502
Code: 5d 18 8f fc 41 80 3e 00 0f 85 a5 01 00 00 89 d8 48 c1 e0 06 49 03 84 24 68 01 00 00 48 8d 78 30 49 89 c7 48 89 fa 48 c1 ea 03 <80> 3c 2a 00 0f 85 98 01 00 00 4d 39 6f 30 75 83 e8 22 18 8f fc 49
RSP: 0018:
ffffc9000300ee80 EFLAGS:
00010206
RAX:
0000000000000000 RBX:
0000000000000000 RCX:
ffffc90016c11000
RDX:
0000000000000006 RSI:
ffffffff84eb6bf3 RDI:
0000000000000030
RBP:
dffffc0000000000 R08:
0000000000000005 R09:
00000000ffffffff
R10:
0000000000000000 R11:
0000000000000000 R12:
ffff888027c80c80
R13:
ffff88807d7ff800 R14:
ffffed1004f901bd R15:
0000000000000000
FS:
00007f6f46c58700(0000) GS:
ffff8880b9b00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000020010000 CR3:
00000000516cc000 CR4:
00000000003506e0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
<TASK>
alb_fasten_mac_swap+0x886/0xa80 drivers/net/bonding/bond_alb.c:1070
bond_alb_handle_active_change+0x624/0x1050 drivers/net/bonding/bond_alb.c:1765
bond_change_active_slave+0xfa1/0x29b0 drivers/net/bonding/bond_main.c:1173
bond_select_active_slave+0x23f/0xa50 drivers/net/bonding/bond_main.c:1253
bond_enslave+0x3b34/0x53b0 drivers/net/bonding/bond_main.c:2159
do_set_master+0x1c8/0x220 net/core/rtnetlink.c:2577
rtnl_newlink_create net/core/rtnetlink.c:3380 [inline]
__rtnl_newlink+0x13ac/0x17e0 net/core/rtnetlink.c:3580
rtnl_newlink+0x64/0xa0 net/core/rtnetlink.c:3593
rtnetlink_rcv_msg+0x43a/0xc90 net/core/rtnetlink.c:6089
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2501
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x917/0xe10 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:734
____sys_sendmsg+0x6eb/0x810 net/socket.c:2492
___sys_sendmsg+0xf3/0x170 net/socket.c:2546
__sys_sendmsg net/socket.c:2575 [inline]
__do_sys_sendmsg net/socket.c:2584 [inline]
__se_sys_sendmsg net/socket.c:2582 [inline]
__x64_sys_sendmsg+0x132/0x220 net/socket.c:2582
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7f6f45a89109
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:
00007f6f46c58168 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
00007f6f45b9c030 RCX:
00007f6f45a89109
RDX:
0000000000000000 RSI:
0000000020000080 RDI:
0000000000000006
RBP:
00007f6f45ae308d R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00007ffed99029af R14:
00007f6f46c58300 R15:
0000000000022000
</TASK>
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20220627102813.126264-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleksij Rempel [Fri, 24 Jun 2022 07:51:38 +0000 (09:51 +0200)]
net: asix: fix "can't send until first packet is send" issue
commit
805206e66fab4ba1e0ebd19402006d62cd1d4902 upstream.
If cable is attached after probe sequence, the usbnet framework would
not automatically start processing RX packets except at least one
packet was transmitted.
On systems with any kind of address auto configuration this issue was
not detected, because some packets are send immediately after link state
is changed to "running".
With this patch we will notify usbnet about link status change provided by the
PHYlib.
Fixes:
e532a096be0e ("net: usb: asix: ax88772: add phylib support")
Reported-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Anton Lundin <glance@acc.umu.se>
Link: https://lore.kernel.org/r/20220624075139.3139300-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Victor Nogueira [Thu, 23 Jun 2022 14:07:41 +0000 (11:07 -0300)]
net/sched: act_api: Notify user space if any actions were flushed before error
commit
76b39b94382f9e0a639e1c70c3253de248cc4c83 upstream.
If during an action flush operation one of the actions is still being
referenced, the flush operation is aborted and the kernel returns to
user space with an error. However, if the kernel was able to flush, for
example, 3 actions and failed on the fourth, the kernel will not notify
user space that it deleted 3 actions before failing.
This patch fixes that behaviour by notifying user space of how many
actions were deleted before flush failed and by setting extack with a
message describing what happened.
Fixes:
55334a5db5cd ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Victor Nogueira <victor@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liang He [Wed, 22 Jun 2022 04:06:21 +0000 (12:06 +0800)]
net/dsa/hirschmann: Add missing of_node_get() in hellcreek_led_setup()
commit
16d584d2fc8f4ea36203af45a76becd7093586f1 upstream.
of_find_node_by_name() will decrease the refcount of its first arg and
we need a of_node_get() to keep refcount balance.
Fixes:
7d9ee2e8ff15 ("net: dsa: hellcreek: Add PTP status LEDs")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220622040621.4094304-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Tue, 21 Jun 2022 12:01:41 +0000 (14:01 +0200)]
netfilter: nft_dynset: restore set element counter when failing to update
commit
05907f10e235680cc7fb196810e4ad3215d5e648 upstream.
This patch fixes a race condition.
nft_rhash_update() might fail for two reasons:
- Element already exists in the hashtable.
- Another packet won race to insert an entry in the hashtable.
In both cases, new() has already bumped the counter via atomic_add_unless(),
therefore, decrement the set element counter.
Fixes:
22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masahiro Yamada [Mon, 13 Jun 2022 17:09:00 +0000 (02:09 +0900)]
s390: remove unneeded 'select BUILD_BIN2C'
commit
25deecb21c18ee29e3be8ac6177b2a9504c33d2d upstream.
Since commit
4c0f032d4963 ("s390/purgatory: Omit use of bin2c"),
s390 builds the purgatory without using bin2c.
Remove 'select BUILD_BIN2C' to avoid the unneeded build of bin2c.
Fixes:
4c0f032d4963 ("s390/purgatory: Omit use of bin2c")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20220613170902.1775211-1-masahiroy@kernel.org
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eli Cohen [Mon, 13 Jun 2022 07:59:57 +0000 (10:59 +0300)]
vdpa/mlx5: Update Control VQ callback information
commit
40f2f3e94178d45e4ee6078effba2dfc76f6f5ba upstream.
The control VQ specific information is stored in the dedicated struct
mlx5_control_vq. When the callback is updated through
mlx5_vdpa_set_vq_cb(), make sure to update the control VQ struct.
Fixes:
5262912ef3cf ("vdpa/mlx5: Add support for control VQ and MAC setting")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <
20220613075958.511064-1-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Miaoqian Lin [Thu, 26 May 2022 08:28:56 +0000 (12:28 +0400)]
PM / devfreq: exynos-ppmu: Fix refcount leak in of_get_devfreq_events
commit
f44b799603a9b5d2e375b0b2d54dd0b791eddfc2 upstream.
of_get_child_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
This function only calls of_node_put() in normal path,
missing it in error paths.
Add missing of_node_put() to avoid refcount leak.
Fixes:
f262f28c1470 ("PM / devfreq: event: Add devfreq_event class")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Wang [Mon, 20 Jun 2022 05:11:14 +0000 (13:11 +0800)]
caif_virtio: fix race between virtio_device_ready() and ndo_open()
commit
11a37eb66812ce6a06b79223ad530eb0e1d7294d upstream.
We currently depend on probe() calling virtio_device_ready() -
which happens after netdev
registration. Since ndo_open() can be called immediately
after register_netdev, this means there exists a race between
ndo_open() and virtio_device_ready(): the driver may start to use the
device (e.g. TX) before DRIVER_OK which violates the spec.
Fix this by switching to use register_netdevice() and protect the
virtio_device_ready() with rtnl_lock() to make sure ndo_open() can
only be called after virtio_device_ready().
Fixes:
0d2e1a2926b18 ("caif_virtio: Introduce caif over virtio")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <
20220620051115.3142-3-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-rpi.git / log