Dave Stevenson [Wed, 1 Jul 2020 09:57:57 +0000 (10:57 +0100)]
media: bcm2835-unicam: Add support for unpacked 14bit Bayer formats
Now that the 14bit non-packed Bayer formats are defined, add them
into the supported formats lookup table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 17:03:47 +0000 (18:03 +0100)]
media: bcm2835-unicam: Add support for 14bit mono sources
Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined,
allow passing 14bit mono data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 16:53:32 +0000 (17:53 +0100)]
media: bcm2835-unicam: Add support for 12bit mono packed format
Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit
mono packed data through the peripheral.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 16:51:03 +0000 (17:51 +0100)]
media: Add a pixel format for MIPI packed 14bit luma only.
This is the format used by monochrome 14bit image sensors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 7 May 2020 15:59:03 +0000 (16:59 +0100)]
media: Add a pixel format for MIPI packed 12bit luma only.
This is the format used by monochrome 12bit image sensors.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Thu, 2 Jul 2020 12:53:20 +0000 (13:53 +0100)]
serial: 8250: bcm2835aux - defer if clock is zero
See: https://github.com/raspberrypi/linux/issues/3700
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dave Stevenson [Fri, 26 Jun 2020 17:11:49 +0000 (18:11 +0100)]
media: i2c: imx290: Switch set_hmax to use imx290_write_buffered_reg
imx290_set_hmax was using two independent writes to set up hmax,
when all other multi-register writes were using imx290_write_buffered_reg
which claims the group hold first.
Switch imx290_set_hmax to using imx290_write_buffered_reg too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 16:03:11 +0000 (17:03 +0100)]
media : i2c: imx290: Add support for the mono sensor variant.
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 15:52:14 +0000 (16:52 +0100)]
media: dt-bindings: media: i2c: Add mono version to IMX290 bindings
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 11 Jun 2020 17:34:16 +0000 (18:34 +0100)]
media: i2c: imx290: Add H and V flip controls
The sensor supports horizontal and vertical flips, so support them
through V4L2_CID_HFLIP and V4L2_CID_VFLIP.
This sensor does NOT change the Bayer order when changing the
direction of readout, therefore no special handling is required for
that.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 11 Jun 2020 17:19:13 +0000 (18:19 +0100)]
media: i2c: imx290: Add exposure control to the driver.
Adds support for V4L2_CID_EXPOSURE so that userspace can control
the sensor exposure time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 11 Jun 2020 17:09:12 +0000 (18:09 +0100)]
media: i2c: imx290: Add support for V4L2_CID_VBLANK
In order to calculate framerate and durations userspace needs
the vertical blanking information. This can be configurable,
and indeed the datasheet lists different values for VBLANK for
the 1080p and 720p modes.
Add the new control, and adopt the datasheet values for each mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 11 Jun 2020 13:36:40 +0000 (14:36 +0100)]
media: i2c: imx290: Convert HMAX setting into V4L2_CID_HBLANK
Userspace needs to know HBLANK if it is to work out exposure times
and frame rates, therefore convert it to map onto V4L2_CID_HBLANK
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 11 Jun 2020 12:41:43 +0000 (13:41 +0100)]
media: i2c: imx290: Correct range for V4L2_CID_GAIN to 0-238
The datasheet lists the gain as being 0.0 to 72.0dB in 0.3dB steps, which
makes 238 steps total.
Correct the 0-72 range defined in the driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 25 Jun 2020 07:28:51 +0000 (08:28 +0100)]
media: i2c: imx290: Add support for 74.25MHz clock
The existing driver only supported a clock of 37.125MHz, but the
sensor also supports 74.25MHz.
Add the relevant register modifications to support this alternate
clock frequency.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Andrey Konovalov [Fri, 12 Jun 2020 13:53:46 +0000 (15:53 +0200)]
media: i2c: imx290: set the format before VIDIOC_SUBDEV_G_FMT is called
Commit
d46cfdc86c30d5ec768924f0b1e2683c8d20b671 upstream.
With the current driver 'media-ctl -p' issued right after the imx290 driver
is loaded prints:
pad0: Source
[fmt:unknown/0x0]
The format value of zero is due to the current_format field of the imx290
struct not being initialized yet.
As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field
is also initialized, so the line which set current_mode to a default value
in driver's probe() function is no longer needed.
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dave Stevenson [Fri, 26 Jun 2020 14:53:44 +0000 (15:53 +0100)]
media: bcm2835-unicam: Avoid gcc warning over {0} on endpoint
Older gcc versions object to = { 0 } initialisation if the first
elemtn in the structure is a substructure.
Use = { } to avoid this compiler warning.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 23 Jun 2020 13:32:51 +0000 (14:32 +0100)]
media: bcm2835-unicam: Add support for get_mbus_config to set num lanes
Use the get_mbus_config pad subdev call to allow a source to use
fewer than the number of CSI2 lanes defined in device tree.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Naushir Patuck [Mon, 4 May 2020 09:25:41 +0000 (12:25 +0300)]
media: bcm2835-unicam: Driver for CCP2/CSI2 camera interface
Add a driver for the Unicam camera receiver block on BCM283x processors.
Compared to the bcm2835-camera driver present in staging, this driver
handles the Unicam block only (CSI-2 receiver), and doesn't depend on
the VC4 firmware running on the VPU.
The commit is made up of a series of changes cherry-picked from the
rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with
additional enhancements, forward-ported to the mainline kernel.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: kbuild test robot <lkp@intel.com>
Dave Stevenson [Tue, 23 Jun 2020 09:05:57 +0000 (10:05 +0100)]
drivers: media: Remove the downstream version of bcm2835-unicam
About to be replaced by the upstream version.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Fri, 26 Jun 2020 10:51:05 +0000 (11:51 +0100)]
brcmfmac: Prefer a ccode from OTP over nvram file
Allow the nvram file to set a default ccode (regulatory domain) without
overriding one set in OTP.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Maxim Mikityanskiy [Sat, 20 Jun 2020 12:40:00 +0000 (15:40 +0300)]
staging: bcm2835-audio: Add missing MODULE_ALIAS
Commit
8353fe6f1e0f ("Revert "staging: bcm2835-audio: Drop DT
dependency"") reverts the upstream change and makes bcm2835-audio use
device tree again, however, it also removes the MODULE_ALIAS for the
platform device. This MODULE_ALIAS is needed, because VCHIQ registers
bcm2835-audio as a child platform device since commit
25c7597af20d
("staging: vchiq_arm: Register a platform device for audio"), and this
mechanism is adopted also in the downstream kernel.
This commit puts back that MODULE_ALIAS to make bcm2835-audio
autoprobing work again. The rest of VCHIQ children have their
MODULE_ALIASes in place.
Fixes:
8353fe6f1e0f ("Revert "staging: bcm2835-audio: Drop DT dependency"")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Markus Proeller [Tue, 16 Jun 2020 11:33:56 +0000 (13:33 +0200)]
media: irs1125: Keep HW in sync after imager reset
When closing the video device, the irs1125 is put in power down state.
To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is
called after power up.
The compound ctrl IRS1125_CID_MOD_PLL however has a default value
of all zeros, which puts the imager into a non responding state.
Thus, this ctrl is not written by the driver into HW after power up.
The userspace has to take care to write senseful data.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Tue, 16 Jun 2020 11:31:36 +0000 (13:31 +0200)]
media: irs1125: Atomic access to imager reconfiguration
Instead of changing the exposure and framerate settings for all sequences,
they can be changed for every sequence individually now. Therefore the
IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by
IRS1125_CID_SAFE_RECONFIG_S<seq_num>_EXPO and *_FRAME ctrls.
The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG
is removed.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Tue, 16 Jun 2020 11:27:42 +0000 (13:27 +0200)]
media: irs1125: Refactoring and debug messages
Changed some variable names to comply with checkpatch --strict mode.
Debug messages added.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Tue, 16 Jun 2020 11:24:31 +0000 (13:24 +0200)]
media: irs1125: Using i2c_transfer for ic2 reads
Reading data over i2c is done by using i2c_transfer to ensure that this
operation can't be interrupted.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Phil Elwell [Thu, 11 Jun 2020 08:57:03 +0000 (09:57 +0100)]
PCI: brcmstb: Add DT property to control L1SS
The BRCM PCIe block has controls to enable control of the CLKREQ#
signal by the L1SS, and to gate the refclk with the CLKREQ# input.
These controls are mutually exclusive - the upstream code sets the
latter, but some use cases require the former.
Add a Device Tree property - brcm,enable-l1ss - to switch to the
L1SS configuration.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Tue, 24 Apr 2018 13:42:27 +0000 (14:42 +0100)]
gpiolib: Don't prevent IRQ usage of output GPIOs
Upstream Linux deems using output GPIOs to generate IRQs as a bogus
use case, even though the BCM2835 GPIO controller is capable of doing
so. A number of users would like to make use of this facility, so
disable the checks.
See: https://github.com/raspberrypi/linux/issues/2527
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Hristo Venev [Fri, 5 Jun 2020 09:22:49 +0000 (09:22 +0000)]
snd_bcm2835: disable HDMI audio when vc4 is used (#3640)
Things don't work too well when both the vc4 driver and the firmware
driver are trying to control the same audio output:
[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5
Hence, when the vc4 HDMI driver is used, let it control audio. This is done
by introducing a new device tree property to the audio node, and
extending the vc4-kms-v3d overlays to set it appropriately.
Signed-off-by: Hristo Venev <hristo@venev.name>
David Plowman [Thu, 28 May 2020 10:09:48 +0000 (11:09 +0100)]
media: bcm2835-unicam: change minimum number of vb2_queue buffers to 1
Since the unicam driver was modified to write to a dummy buffer when no
user-supplied buffer is available, it can now write to and return a
buffer even when there's only a single one. Enable this by changing the
min_buffers_needed in the vb2_queue; it will be useful for enabling
still captures without allocating more memory than absolutely necessary.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
Phil Elwell [Tue, 5 May 2020 14:23:32 +0000 (15:23 +0100)]
zswap: Defer zswap initialisation
Enabling zswap support in the kernel configuration costs about 1.5MB
of RAM, even when zswap is not enabled at runtime. This cost can be
reduced significantly by deferring initialisation (including pool
creation) until the "enabled" parameter is set to true. There is a
small cost to this in that some initialisation code has to remain in
memory after the init phase, just in case they are needed later,
but the total size increase is negligible.
See: https://github.com/raspberrypi/linux/pull/3432
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dave Stevenson [Tue, 19 May 2020 10:46:47 +0000 (11:46 +0100)]
media: bcm2835-unicam: Retain packing information on G_FMT
The change to retrieve the pixel format always on g_fmt didn't
check whether the native or unpacked version of the format
had been requested, and always returned the packed one.
Correct this so that the packing setting is retained whereever
possible.
Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev
on a g_fmt call"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 15 May 2020 12:48:59 +0000 (13:48 +0100)]
staging:vc04_services: bcm2835-camera: Request headers with I-frame
V4L2 wishes to have the codec header bytes in the same buffer as the
first encoded frame, so it does become 1-in 1-out for encoding.
The firmware now has an option to do this, so enable it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 15 May 2020 12:42:10 +0000 (13:42 +0100)]
staging: vc04_services: mmal-vchiq: Update parameters list
Adds in a couple of new MMAL parameter defines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Wed, 13 May 2020 19:10:15 +0000 (20:10 +0100)]
sc16is7xx: Fix for hardware flow control
The SC16IS7XX hardware flow control is mishandled by the driver in
a number of ways:
1. The set_baud method accidentally clears it when setting EFR bit.
2. Even though hardware flow control is enabled, it isn't indicated
back to the serial framework.
3. Applying the flow control clears the EFR bit.
4. The CTS support is not indicated in the return from
sc16is7xx_get_mctrl.
Address all of those issues using a mixture of patches found on the
linked pages.
See: https://github.com/raspberrypi/linux/issues/2542
See: https://www.spinics.net/lists/linux-serial/msg21794.html
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dave Stevenson [Wed, 13 May 2020 17:28:27 +0000 (18:28 +0100)]
media: bcm2835-unicam: Always service interrupts
From when bringing up the driver, there was a check in the isr
to ignore interrupts (claiming them handled) should the driver
not be streaming.
The VPU now will not register a camera driver if it finds a
CSI2 node enabled in device tree, therefore this flawed check is
redundant.
https://github.com/raspberrypi/linux/issues/3602
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Naushir Patuck [Thu, 7 May 2020 14:50:54 +0000 (15:50 +0100)]
dt-bindings: media: i2c: Add IMX477 CMOS sensor binding
Add YAML device tree binding for IMX477 CMOS image sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Phil Elwell [Tue, 5 May 2020 18:45:41 +0000 (19:45 +0100)]
video: bcm2708_fb: Disable FB if no displays found
If the firmware hasn't detected a display, the driver would assume
one display was available, but because it had failed to retrieve the
display size it would try to allocate a zero-sized buffer.
Avoid the allocation failure by bailing out early if no display is
found.
See: https://github.com/raspberrypi/linux/issues/3598
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Jacko Dirks [Tue, 5 May 2020 12:33:31 +0000 (14:33 +0200)]
media: bcm2835: unicam: Fix uninitialized warning
Signed-off-by: Jacko Dirks <jdirks.linuxdev@gmail.com>
Jacko Dirks [Tue, 5 May 2020 12:28:14 +0000 (14:28 +0200)]
media: i2c: tc358743: Fix fallthrough warning
Signed-off-by: Jacko Dirks <jdirks.linuxdev@gmail.com>
Dave Stevenson [Thu, 30 Apr 2020 08:52:50 +0000 (09:52 +0100)]
media: bcm2835-unicam: Fix reference counting in unicam_open
The reference counting of node->open was only incremented after
a check that the node was v4l2_fh_is_singular_file, which resulted
in the counting going wrong and s_power not being called at an
appropriate time.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 29 Apr 2020 21:05:09 +0000 (22:05 +0100)]
media: bcm2835-unicam: Do not stop streaming in unicam_release
unicam_release calls _vb2_fop_release, which will call stop_streaming
if that particular node was streaming. Calling it unconditionally (as
the code was) means that if a second handle was opened eg to alter
a setting, on closing that connection it also stopped Unicam.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 29 Apr 2020 15:45:02 +0000 (16:45 +0100)]
media: bcm2835-unicam: Add support for VIDIOC_[S|G]_SELECTION
Sensors are now reflecting cropping and scaling parameters through
the selection API, therefore Unicam needs to forward the requests
through to the subdev.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Thu, 4 Apr 2019 12:33:47 +0000 (13:33 +0100)]
bcm2835-dma: Add proper 40-bit DMA support
BCM2711 has 4 DMA channels with a 40-bit address range, allowing them
to access the full 4GB of memory on a Pi 4.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Naushir Patuck [Wed, 22 Apr 2020 07:32:32 +0000 (08:32 +0100)]
staging: vchiq: Load bcm2835_isp driver from vchiq
bcmn2835_isp is a platform driver dependent on vchiq,
therefore add the load/unload functions for it to vchiq.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 21 Apr 2020 14:06:19 +0000 (15:06 +0100)]
media: uapi: v4l-ctrls: Add CID base for the bcm2835-isp driver
We are reserving controls for the new bcm2835-isp driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Thu, 23 Apr 2020 09:20:26 +0000 (10:20 +0100)]
media: uapi: v4l2-core: Add ISP statistics output V4L2 fourcc type
Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type.
This new format will be used by the BCM2835 ISP device to return
out ISP statistics for 3A.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 21 Apr 2020 15:26:03 +0000 (16:26 +0100)]
media: bcm2835-unicam: Re-fetch mbus code from subdev on a g_fmt call
The sensor subdevice may change the Bayer order if a H/V flip is
requested after a s_fmt call. Unicam g_fmt must call the subdev get_fmt
in case this has happened and return out the correct format 4cc.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Laurent Pinchart [Tue, 24 Mar 2020 21:13:02 +0000 (23:13 +0200)]
media: bcm2835-unicam: Add support for the FRAME_SYNC event
The FRAME_SYNC event is useful for userspace image processing algorithms
to program the camera sensor as early as possible after frame start.
Support it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Laurent Pinchart [Tue, 24 Mar 2020 21:13:02 +0000 (23:13 +0200)]
media: bcm2835-unicam: Disable event-related ioctls on metadata node
The unicam driver supports both the SOURCE_CHANGE and CTRL events. Both
events are only generated on the image video node, so the event-related
ioctls are useless on the medatada node. Disable them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Thu, 2 Apr 2020 15:08:51 +0000 (16:08 +0100)]
media: bcm2835-unicam: Use dummy buffer if none have been queued
If no buffer has been queued by a userland application, we use an
internal dummy buffer for the hardware to spin in. This will allow
the driver to release the existing userland buffer back to the
application for processing.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Thu, 16 Apr 2020 10:35:41 +0000 (11:35 +0100)]
media: bcm2835-unicam: Add embedded data node.
This patch adds a new node in the bcm2835-unicam driver to support
CSI-2 embedded data streams. The subdevice is queried to see if
embedded data is available from the sensor.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 7 Apr 2020 09:42:14 +0000 (10:42 +0100)]
media: bcm2835-unicam: Add support for mulitple device nodes.
Move device node specific state out of the device state structure and
into a new node structure. This separation will be needed for future
changes where we will add an embedded data node to the driver to work
alongside the existing image data node.
Currently only use a single image node, so this commit does not add
any functional changes.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Tue, 21 Jan 2020 14:06:47 +0000 (14:06 +0000)]
media: uapi: Add MEDIA_BUS_FMT_SENSOR_DATA media bus format
This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam
driver to support CSI-2 embedded data streams from camera sensors.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Wed, 1 Apr 2020 07:46:29 +0000 (08:46 +0100)]
media: uapi: v4l2-core: Add sensor ancillary data V4L2 foucc type.
Add V4L2_META_FMT_SENSOR_DATA format 4CC.
This new format will be used by the BCM2835 Unicam device to return
out camera sensor embedded data.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Naushir Patuck [Wed, 1 Apr 2020 07:39:49 +0000 (08:39 +0100)]
media: bcm2835-unicam: Driver for CCP2/CSI2 camera interface
Add driver for the Unicam camera receiver block on
BCM283x processors.
This commit is made up of a series of changes cherry-picked from the
rpi-4.19.y branch.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Phil Elwell [Tue, 21 Apr 2020 10:30:23 +0000 (11:30 +0100)]
driver: char: rpivid: Don't map more than wanted
Limit mappings to the permitted range, but don't map more than asked
for otherwise we walk off the end of the allocated VMA.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Fri, 17 Apr 2020 09:46:19 +0000 (10:46 +0100)]
spi: Force CS_HIGH if GPIO descriptors are used
Commit
f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose
Chip Select is defined by a "cs-gpios" devicetree property.
This change breaks drivers whose probe functions set the mode field of
the spi_device because in doing so they clear the SPI_CS_HIGH flag.
Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as
in of_spi_parse_dt()).
See also:
83b2a8fe43bd ("spi: spidev: Fix CS polarity if GPIO descriptors are used")
Fixes:
f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG
This warning is unavoidable from a client's perspective and
doesn't indicate anything wrong (just surprising).
SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 20 Apr 2020 21:18:52 +0000 (22:18 +0100)]
driver: char: rpivid: Remove legacy name support
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Dave Stevenson [Mon, 27 Jan 2020 10:22:44 +0000 (10:22 +0000)]
drm: Checking of the pitch is only valid for linear formats
framebuffer_check was computing a minimum pitch value and ensuring
that the provided value was greater than this.
That check is only valid if the format is linear.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Maxime Ripard [Thu, 13 Feb 2020 15:45:24 +0000 (16:45 +0100)]
dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI controllers bindings
The HDMI controllers found in the BCM2711 SoC need some adjustments to the
bindings, especially since the registers have been shuffled around in more
register ranges.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Thu, 13 Feb 2020 16:51:09 +0000 (17:51 +0100)]
dt-bindings: clock: Add a binding for the RPi Firmware clocks
The firmare running on the RPi VideoCore can be used to discover and
change the various clocks running in the BCM2711. Since devices will
need to use them through the DT, let's add a pretty simple binding.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
John Cox [Thu, 5 Mar 2020 18:30:41 +0000 (18:30 +0000)]
staging: media: Add Raspberry Pi V4L2 H265 decoder
This driver is for the HEVC/H265 decoder block on the Raspberry
Pi 4, and conforms to the V4L2 stateless decoder API.
Signed-off-by: John Cox <jc@kynesim.co.uk>
Dave Stevenson [Tue, 17 Mar 2020 10:53:16 +0000 (10:53 +0000)]
media: dt-bindings: media: Add binding for the Raspberry PI HEVC decoder
Adds a binding for the HEVC decoder found on the BCM2711 / Raspberry Pi 4.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 24 Jan 2020 14:28:21 +0000 (14:28 +0000)]
media: videodev2.h: Add a format for column YUV4:2:0 modes
Some of the Broadcom codec blocks use a column based YUV4:2:0 image
format, so add the documentation and defines for both 8 and 10 bit
versions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Jernej Skrabec [Fri, 13 Dec 2019 16:04:27 +0000 (17:04 +0100)]
media: uapi: hevc: Add segment address field
From https://patchwork.linuxtv.org/patch/60725/
Changes requested, but mainly docs.
If HEVC frame consists of multiple slices, segment address has to be
known in order to properly decode it.
Add segment address field to slice parameters.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Jernej Skrabec [Fri, 13 Dec 2019 16:04:25 +0000 (17:04 +0100)]
media: uapi: hevc: Add scaling matrix control
Taken from https://patchwork.linuxtv.org/patch/60728/
Changes (mainly documentation) have been requested.
HEVC has a scaling matrix concept. Add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Dave Stevenson [Fri, 24 Jan 2020 14:22:06 +0000 (14:22 +0000)]
drm/fourcc: Add packed 10bit YUV 4:2:0 format
Adds a format that is 3 10bit YUV 4:2:0 samples packed into
a 32bit work (with 2 spare bits).
Supported on Broadcom BCM2711 chips.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
popcornmix [Wed, 1 Apr 2020 10:22:44 +0000 (11:22 +0100)]
bcmgenet: Disable skip_umac_reset by default
Possible fixed upstream by 'net: bcmgenet: keep MAC in reset until PHY is up'
Signed-off-by: popcornmix <popcornmix@gmail.com>
Jim Quinlan [Mon, 15 Jan 2018 23:28:39 +0000 (18:28 -0500)]
dt-bindings: pci: Add DT docs for Brcmstb PCIe device
The DT bindings description of the Brcmstb PCIe device is described. This
node can be used by almost all Broadcom settop box chips, using
ARM, ARM64, or MIPS CPU architectures.
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Phil Elwell [Thu, 6 Feb 2020 12:23:15 +0000 (12:23 +0000)]
of: overlay: Correct symbol path fixups
When symbols from overlays are added to the live tree their paths must
be rebased. The translated symbol is normally the result of joining
the fragment-relative path (with a leading "/") to the target path
(either copied directly from the "target-path" property or resolved
from the phandle). This translation fails when the target is the root
node (a common case for Raspberry Pi overlays) because the resulting
path starts with a double slash. For example, if target-path is "/" and
the fragment adds a node called "newnode", the label associated with
that node will be assigned the path "//newnode", which can't be found
in the tree.
Fix the failure case by explicitly replacing a target path of "/" with
an empty string.
Fixes:
d1651b03c2df ("of: overlay: add overlay symbols to live device tree")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 2 Mar 2020 14:42:23 +0000 (14:42 +0000)]
video: fbdev: bcm2708_fb: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 2 Mar 2020 14:40:19 +0000 (14:40 +0000)]
drivers: char: vcio: Use common compat header
The definition of compat_ptr is now common for most platforms, but
requires the inclusion of <linux/compat.h>.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 6 Jan 2020 16:04:30 +0000 (16:04 +0000)]
pinctrl: bcm2835: Remove gpiochip on error
A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix
the leak with the use of devm_gpiochip_add_data.
Fixes:
85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 3 Feb 2020 17:30:46 +0000 (17:30 +0000)]
staging: vchiq_arm: Give vchiq children DT nodes
vchiq kernel clients are now instantiated as platform drivers rather
than using DT, but the children of the vchiq interface may still
benefit from access to DT properties. Give them the option of a
a sub-node of the vchiq parent for configuration and to allow
them to be disabled.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Luke Hinds [Wed, 22 Jan 2020 16:03:00 +0000 (16:03 +0000)]
Initialise rpi-firmware before clk-bcm2835
The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted
Platform Module) having been registered when it initialises; otherwise
it assumes there is no TPM. It has been observed on BCM2835 that IMA
is initialised before TPM, and that initialising the BCM2835 clock
driver before the firmware driver has the effect of reversing this
order.
Change the firmware driver to initialise at core_initcall, delaying the
BCM2835 clock driver to postcore_initcall.
See: https://github.com/raspberrypi/linux/issues/3291
https://github.com/raspberrypi/linux/pull/3297
Signed-off-by: Luke Hinds <lhinds@redhat.com>
Co-authored-by: Phil Elwell <phil@raspberrypi.org>
Stefan Wahren [Fri, 27 Dec 2019 10:40:56 +0000 (11:40 +0100)]
ARM: bcm: Backport BCM2711 support from upstream
Make the BCM2711 a different machine, but keep it in board_bcm2835.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Dave Stevenson [Tue, 18 Jun 2019 11:15:50 +0000 (12:15 +0100)]
staging: vchiq: Use the old dma controller for OF config on platform devices
vchiq on Pi4 is no longer under the soc node, therefore it
doesn't get the dma-ranges for the VPU.
Switch to using the configuration of the old dma controller as
that will set the dma-ranges correctly.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Tue, 29 Jan 2019 16:13:25 +0000 (16:13 +0000)]
staging: vchiq_arm: Set up dma ranges on child devices
The VCHIQ driver now loads the audio, camera, codec, and vc-sm
drivers as platform drivers. However they were not being given
the correct DMA configuration.
Call of_dma_configure with the parent (VCHIQ) parameters to be
inherited by the child.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
popcornmix [Tue, 3 Sep 2019 19:28:00 +0000 (20:28 +0100)]
clk-bcm2835: Disable v3d clock
This is controlled by firmware, see clk-raspberrypi.c
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Mon, 9 Sep 2019 14:49:56 +0000 (15:49 +0100)]
clk-raspberrypi: Allow cpufreq driver to also adjust gpu clocks
For performance/power it is beneficial to adjust gpu clocks with arm clock.
This is how the downstream cpufreq driver works
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Thu, 5 Sep 2019 16:59:14 +0000 (17:59 +0100)]
v3d_gem: Kick the clock so firmware knows we are using firmware clock interface
Setting the v3d clock to low value allows firmware to handle dvfs in case
where v3d hardware is not being actively used (e.g. console use).
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Fri, 23 Aug 2019 15:34:38 +0000 (16:34 +0100)]
v3d_drv: Handle missing clock more gracefully
Signed-off-by: popcornmix <popcornmix@gmail.com>
James Hughes [Thu, 31 Oct 2019 14:39:44 +0000 (14:39 +0000)]
net:phy:2711 Allow ethernet LED mode to be set via device tree
Add device tree entries and code to allow the specification of
the lighting modes for the LED's on the ethernet connector.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
net:phy:2711 Change the default ethernet LED actions
This should return default behaviour back to that of previous
releases.
Dave Stevenson [Wed, 6 Nov 2019 13:57:58 +0000 (13:57 +0000)]
staging: vchiq_arm: Register bcm2835-codec as a platform driver
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the V4L2 codec driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 6 Nov 2019 13:57:48 +0000 (13:57 +0000)]
staging: vchiq_arm: Register vcsm-cma as a platform driver
Following the same pattern as bcm2835-camera and bcm2835-audio,
register the vcsm-cma driver as a platform driver
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Phil Elwell [Tue, 12 Nov 2019 16:41:21 +0000 (16:41 +0000)]
drm/v3d: Plug dma_fence leak
The irq_fence and done_fence are given a reference that is never
released. The necessary dma_fence_put()s seem to have been
deleted in error in an earlier commit.
Fixes:
0b73676836b2 ("drm/v3d: Clock V3D down when not in use.")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 11 Nov 2019 20:18:08 +0000 (20:18 +0000)]
drm/v3d: Suppress all but the first MMU error
The v3d driver currently encounters a lot of MMU PTE exceptions, so
only log the first to avoid swamping the kernel log.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Markus Proeller [Thu, 10 Oct 2019 17:12:36 +0000 (19:12 +0200)]
media: i2c: Add a driver for the Infineon IRS1125 depth sensor
The Infineon IRS1125 is a time of flight depth sensor that
has a CSI-2 interface.
Add a V4L2 subdevice driver for this device.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
Markus Proeller [Thu, 10 Oct 2019 17:12:08 +0000 (19:12 +0200)]
dt-bindings: Add binding for the Infineon IRS1125 sensor
Adds a binding for the Infineon IRS1125 time-of-flight depth
sensor.
Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
James Hughes [Tue, 24 Sep 2019 17:26:55 +0000 (18:26 +0100)]
Rename HDMI ALSA device names, check for enable state
HDMI Alsa devices renamed to match names used by DRM, to
HDMI 1 and HDMI 2
Check for which HDMI devices are connected and only create
devices for those that are present.
The rename of the devices might cause some backwards compatibility
issues, but since this particular part of the driver needs to be
specifically enabled, I suspect the number of people who will see
the problem will be very small.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Stefan Wahren [Thu, 19 Sep 2019 18:45:30 +0000 (20:45 +0200)]
ARM: bcm: Switch board, clk and pinctrl to bcm2711 compatible
After the decision to use bcm2711 compatible for upstream, we should
switch all accepted compatibles to bcm2711. So we can boot with
one DTB the down- and the upstream kernel.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Phil Elwell [Wed, 18 Sep 2019 16:22:36 +0000 (17:22 +0100)]
drm/v3d: Delete pm_runtime support
The pm_runtime was blocking changelist submission, so delete it as a
temporary workaround.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Fri, 6 Sep 2019 14:13:06 +0000 (15:13 +0100)]
staging: bcm2835-camera: Add greyworld AWB mode
This is mainly used for the NoIR camera which has no IR
filter and can completely confuse normal AWB presets.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Fri, 6 Sep 2019 14:04:51 +0000 (15:04 +0100)]
v4l2: Add a Greyworld AWB mode.
Adds a simple greyworld white balance preset, mainly for use
with cameras without an IR filter (eg Raspberry Pi NoIR)
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Dave Stevenson [Wed, 28 Aug 2019 12:34:30 +0000 (13:34 +0100)]
media: dt-bindings: Add binding for the Sony IMX219 sensor
The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes.
Document the binding for this device.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Tue, 3 Sep 2019 17:17:25 +0000 (18:17 +0100)]
arch/arm64: Add Revision, Serial, Model to cpuinfo
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 3 Sep 2019 17:16:56 +0000 (18:16 +0100)]
arch/arm: Add model string to cpuinfo
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Thu, 15 Aug 2019 11:02:34 +0000 (12:02 +0100)]
configs: arm64/bcm2711: Enable V3D
Enable the V3D driver, which depends on BCM2835_POWER.
Originally submitted by GitHub user 'phire' in a slightly different
form.
See: https://github.com/raspberrypi/linux/pull/3063
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Jonathan Bell [Tue, 13 Aug 2019 14:53:29 +0000 (15:53 +0100)]
xhci: Use more event ring segment table entries
Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.
Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>