arm64: dts: imx8mm-verdin: correct off-on-delay

[ Upstream commit 130c1f4306d56301216baaea68afdd909892c73f ]

The property should be off-on-delay-us, not off-on-delay

Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: imx8mm-evk: correct pmic clock source

[ Upstream commit 85af7ffd24da38e416a14bd6bf207154d94faa83 ]

The osc_32k supports #clock-cells as 0, using an id is wrong, drop it.

Fixes: a6a355ede574 ("arm64: dts: imx8mm-evk: Add 32.768 kHz clock to PMIC")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: sc8280xp-pmics: fix pon compatible and registers

[ Upstream commit ad8cd35c58ca3ec5e93f52a0124899627b98efb2 ]

The pmk8280 PMIC PON peripheral is gen3 and uses two sets of registers;
hlos and pbs.

This specifically fixes the following error message during boot when the
pbs registers are not defined:

PON_PBS address missing, can't read HW debounce time

Note that this also enables the spurious interrupt workaround introduced
by commit 0b65118e6ba3 ("Input: pm8941-pwrkey - add software key press
debouncing support") (which may or may not be needed).

Fixes: ccd3517faf18 ("arm64: dts: qcom: sc8280xp: Add reference device")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327122948.4323-1-johan+linaro@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: meson-g12-common: specify full DMC range

[ Upstream commit aec4353114a408b3a831a22ba34942d05943e462 ]

According to S905X2 Datasheet - Revision 07:
DRAM Memory Controller (DMC) register area spans ff638000-ff63a000.

According to DeviceTree Specification - Release v0.4-rc1:
simple-bus nodes do not require reg property.

Fixes: 1499218c80c99a ("arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi")
Signed-off-by: Marc Gonzalez <mgonzalez@freebox.fr>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230327120932.2158389-2-mgonzalez@freebox.fr
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: ipq8074-hk10: enable QMP device, not the PHY node

[ Upstream commit 1dc40551f206d20b7e46ea7dd538dcdd928451c6 ]

Correct PCIe PHY enablement to refer the QMP device nodes rather than
PHY device nodes. QMP nodes have 'status = "disabled"' property in the
ipq8074.dtsi, while PHY nodes do not correspond to the actual device and
do not have the status property.

Fixes: 1ed34da63a37 ("arm64: dts: qcom: Add board support for HK10")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324021651.1799969-2-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: hk10: use "okay" instead of "ok"

[ Upstream commit 7284a3943909606016128b79fb18dd107bc0fe26 ]

Use "okay" instead of "ok" in USB nodes as "ok" is deprecated.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221107092930.33325-1-robimarko@gmail.com
Stable-dep-of: 1dc40551f206 ("arm64: dts: qcom: ipq8074-hk10: enable QMP device, not the PHY node")
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: ipq8074-hk01: enable QMP device, not the PHY node

[ Upstream commit 72630ba422b70ea0874fc90d526353cf71c72488 ]

Correct PCIe PHY enablement to refer the QMP device nodes rather than
PHY device nodes. QMP nodes have 'status = "disabled"' property in the
ipq8074.dtsi, while PHY nodes do not correspond to the actual device and
do not have the status property.

Fixes: e8a7fdc505bb ("arm64: dts: ipq8074: qcom: Re-arrange dts nodes based on address")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324021651.1799969-1-dmitry.baryshkov@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Lower sd speed on rk3566-soquartz

[ Upstream commit 5912b647bd0732ae8c78a6e5b259c82efd177d93 ]

Just like the Quartz64 Model B the previously stated speed of sdr-104
in soquartz is too high for the hardware to reliably communicate with
some fast SD cards.
Especially on some carrierboards.

Lower this to sd-uhs-sdr50 to fix this.

Fixes: 5859b5a9c3ac ("arm64: dts: rockchip: add SoQuartz CM4IO dts")
Signed-off-by: Dan Johansen <strit@manjaro.org>
Acked-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20230304164135.28430-1-strit@manjaro.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: rockchip: fix a typo error for rk3288 spdif node

[ Upstream commit 02c84f91adb9a64b75ec97d772675c02a3e65ed7 ]

Fix the address in the spdif node name.

Fixes: 874e568e500a ("ARM: dts: rockchip: Add SPDIF transceiver for RK3288")
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Sjoerd Simons <sjoerd@collabora.com>
Link: https://lore.kernel.org/r/20230208091411.1603142-1-jay.xu@rock-chips.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Linux 6.1.25

Link: https://lore.kernel.org/r/20230418120313.001025904@linuxfoundation.org
Tested-by: Markus Reichelt <lkt+2023@mareichelt.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Chris Paterson (CIP) <chris.paterson2@renesas.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Link: https://lore.kernel.org/r/20230419093701.194867488@linuxfoundation.org
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Link: https://lore.kernel.org/r/20230419132048.193275637@linuxfoundation.org
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Markus Reichelt <lkt+2023@mareichelt.com>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup/cpuset: Add cpuset_can_fork() and cpuset_cancel_fork() methods

[ Upstream commit eee87853794187f6adbe19533ed79c8b44b36a91 ]

In the case of CLONE_INTO_CGROUP, not all cpusets are ready to accept
new tasks. It is too late to check that in cpuset_fork(). So we need
to add the cpuset_can_fork() and cpuset_cancel_fork() methods to
pre-check it before we can allow attachment to a different cpuset.

We also need to set the attach_in_progress flag to alert other code
that a new task is going to be added to the cpuset.

Fixes: ef2c41cf38a7 ("clone3: allow spawning processes into cgroups")
Suggested-by: Michal Koutný <mkoutny@suse.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cgroup/cpuset: Make cpuset_fork() handle CLONE_INTO_CGROUP properly

[ Upstream commit 42a11bf5c5436e91b040aeb04063be1710bb9f9c ]

By default, the clone(2) syscall spawn a child process into the same
cgroup as its parent. With the use of the CLONE_INTO_CGROUP flag
introduced by commit ef2c41cf38a7 ("clone3: allow spawning processes
into cgroups"), the child will be spawned into a different cgroup which
is somewhat similar to writing the child's tid into "cgroup.threads".

The current cpuset_fork() method does not properly handle the
CLONE_INTO_CGROUP case where the cpuset of the child may be different
from that of its parent.  Update the cpuset_fork() method to treat the
CLONE_INTO_CGROUP case similar to cpuset_attach().

Since the newly cloned task has not been running yet, its actual
memory usage isn't known. So it is not necessary to make change to mm
in cpuset_fork().

Fixes: ef2c41cf38a7 ("clone3: allow spawning processes into cgroups")
Reported-by: Giuseppe Scrivano <gscrivan@redhat.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cgroup/cpuset: Skip spread flags update on v2

[ Upstream commit 18f9a4d47527772515ad6cbdac796422566e6440 ]

Cpuset v2 has no spread flags to set. So we can skip spread
flags update if cpuset v2 is being used. Also change the name to
cpuset_update_task_spread_flags() to indicate that there are multiple
spread flags.

Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Stable-dep-of: 42a11bf5c543 ("cgroup/cpuset: Make cpuset_fork() handle CLONE_INTO_CGROUP properly")
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD

[ Upstream commit 74391b3e69855e7dd65a9cef36baf5fc1345affd ]

Added a quirk to fix the TeamGroup T-Force Cardea Zero Z330 SSDs reporting
duplicate NGUIDs.

Signed-off-by: Duy Truong <dory@dory.moe>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-pci: mark Lexar NM760 as IGNORE_DEV_SUBNQN

[ Upstream commit 1231363aec86704a6b0467a12e3ca7bdf890e01d ]

A system with more than one of these SSDs will only have one usable.
The kernel fails to detect more than one nvme device due to duplicate
cntlids.

before:
[    9.395229] nvme 0000:01:00.0: platform quirk: setting simple suspend
[    9.395262] nvme nvme0: pci function 0000:01:00.0
[    9.395282] nvme 0000:03:00.0: platform quirk: setting simple suspend
[    9.395305] nvme nvme1: pci function 0000:03:00.0
[    9.409873] nvme nvme0: Duplicate cntlid 1 with nvme1, subsys nqn.2022-07.com.siliconmotion:nvm-subsystem-sn-                    , rejecting
[    9.409982] nvme nvme0: Removing after probe failure status: -22
[    9.427487] nvme nvme1: allocated 64 MiB host memory buffer.
[    9.445088] nvme nvme1: 16/0/0 default/read/poll queues
[    9.449898] nvme nvme1: Ignoring bogus Namespace Identifiers

after:
[    1.161890] nvme 0000:01:00.0: platform quirk: setting simple suspend
[    1.162660] nvme nvme0: pci function 0000:01:00.0
[    1.162684] nvme 0000:03:00.0: platform quirk: setting simple suspend
[    1.162707] nvme nvme1: pci function 0000:03:00.0
[    1.191354] nvme nvme0: allocated 64 MiB host memory buffer.
[    1.193378] nvme nvme1: allocated 64 MiB host memory buffer.
[    1.211044] nvme nvme1: 16/0/0 default/read/poll queues
[    1.211080] nvme nvme0: 16/0/0 default/read/poll queues
[    1.216145] nvme nvme0: Ignoring bogus Namespace Identifiers
[    1.216261] nvme nvme1: Ignoring bogus Namespace Identifiers

Adding the NVME_QUIRK_IGNORE_DEV_SUBNQN quirk to resolves the issue.

Signed-off-by: Juraj Pecigos <kernel@juraj.dev>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Stable-dep-of: 74391b3e6985 ("nvme-pci: add NVME_QUIRK_BOGUS_NID for T-FORCE Z330 SSD")
Signed-off-by: Sasha Levin <sashal@kernel.org>

cifs: fix negotiate context parsing

[ Upstream commit 5105a7ffce19160e7062aee67fb6b3b8a1b56d78 ]

smb311_decode_neg_context() doesn't properly check against SMB packet
boundaries prior to accessing individual negotiate context entries. This
is due to the length check omitting the eight byte smb2_neg_context
header, as well as incorrect decrementing of len_of_ctxts.

Fixes: 5100d8a3fe03 ("SMB311: Improve checking of negotiate security contexts")
Reported-by: Volker Lendecke <vl@samba.org>
Reviewed-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: ocores: generate stop condition after timeout in polling mode

[ Upstream commit f8160d3b35fc94491bb0cb974dbda310ef96c0e2 ]

In polling mode, no stop condition is generated after a timeout. This
causes SCL to remain low and thereby block the bus. If this happens
during a transfer it can cause slaves to misinterpret the subsequent
transfer and return wrong values.

To solve this, pass the ETIMEDOUT error up from ocores_process_polling()
instead of setting STATE_ERROR directly. The caller is adjusted to call
ocores_process_timeout() on error both in polling and in IRQ mode, which
will set STATE_ERROR and generate a stop condition.

Fixes: 69c8c0c0efa8 ("i2c: ocores: add polling interface")
Signed-off-by: Gregor Herburger <gregor.herburger@tq-group.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Federico Vaga <federico.vaga@cern.ch>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/rtc: Remove __init for runtime functions

[ Upstream commit 775d3c514c5b2763a50ab7839026d7561795924d ]

set_rtc_noop(), get_rtc_noop() are after booting, therefore their __init
annotation is wrong.

A crash was observed on an x86 platform where CMOS RTC is unused and
disabled via device tree. set_rtc_noop() was invoked from ntp:
sync_hw_clock(), although CONFIG_RTC_SYSTOHC=n, however sync_cmos_clock()
doesn't honour that.

  Workqueue: events_power_efficient sync_hw_clock
  RIP: 0010:set_rtc_noop
  Call Trace:
   update_persistent_clock64
   sync_hw_clock

Fix this by dropping the __init annotation from set/get_rtc_noop().

Fixes: c311ed6183f4 ("x86/init: Allow DT configured systems to disable RTC at boot time")
Signed-off-by: Matija Glavinic Pecotic <matija.glavinic-pecotic.ext@nokia.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/59f7ceb1-446b-1d3d-0bc8-1f0ee94b1e18@nokia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/fair: Fix imbalance overflow

[ Upstream commit 91dcf1e8068e9a8823e419a7a34ff4341275fb70 ]

When local group is fully busy but its average load is above system load,
computing the imbalance will overflow and local group is not the best
target for pulling this load.

Fixes: 0b0695f2b34a ("sched/fair: Rework load_balance()")
Reported-by: Tingjia Cao <tjcao980311@gmail.com>
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Tingjia Cao <tjcao980311@gmail.com>
Link: https://lore.kernel.org/lkml/CABcWv9_DAhVBOq2=W=2ypKE9dKM5s2DvoV8-U0+GDwwuKZ89jQ@mail.gmail.com/T/
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/papr_scm: Update the NUMA distance table for the target node

[ Upstream commit b277fc793daf258877b4c0744b52f69d6e6ba22e ]

Platform device helper routines won't update the NUMA distance table
while creating a platform device, even if the device is present on a
NUMA node that doesn't have memory or CPU. This is especially true for
pmem devices. If the target node of the pmem device is not online, we
find the nearest online node to the device and associate the pmem device
with that online node. To find the nearest online node, we should have
the numa distance table updated correctly. Update the distance
information during the device probe.

For a papr scm device on NUMA node 3 distance_lookup_table value for
distance_ref_points_depth = 2 before and after fix is below:

Before fix:
  node 3 distance depth 0  - 0
  node 3 distance depth 1  - 0
  node 4 distance depth 0  - 4
  node 4 distance depth 1  - 2
  node 5 distance depth 0  - 5
  node 5 distance depth 1  - 1

After fix
  node 3 distance depth 0  - 3
  node 3 distance depth 1  - 1
  node 4 distance depth 0  - 4
  node 4 distance depth 1  - 2
  node 5 distance depth 0  - 5
  node 5 distance depth 1  - 1

Without the fix, the nearest numa node to the pmem device (NUMA node 3)
will be picked as 4. After the fix, we get the correct numa node which
is 5.

Fixes: da1115fdbd6e ("powerpc/nvdimm: Pick nearby online node if the device node is not online")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230404041433.1781804-1-aneesh.kumar@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: mchp-pci1xxxx: Update Timing registers

[ Upstream commit aa874cdfec07d4dd9c6f0c356d65c609ba31a26f ]

Update I2C timing registers based on latest hardware design.
This fix does not break functionality of chips with older design and
existing users will not be affected.

Fixes: 361693697249 ("i2c: microchip: pci1xxxx: Add driver for I2C host controller in multifunction endpoint of pci1xxxx switch")
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ubi: Fix deadlock caused by recursively holding work_sem

[ Upstream commit f773f0a331d6c41733b17bebbc1b6cae12e016f5 ]

During the processing of the bgt, if the sync_erase() return -EBUSY
or some other error code in __erase_worker(),schedule_erase() called
again lead to the down_read(ubi->work_sem) hold twice and may get
block by down_write(ubi->work_sem) in ubi_update_fastmap(),
which cause deadlock.

          ubi bgt                        other task
 do_work
  down_read(&ubi->work_sem)          ubi_update_fastmap
  erase_worker                         # Blocked by down_read
   __erase_worker                      down_write(&ubi->work_sem)
    schedule_erase
     schedule_ubi_work
      down_read(&ubi->work_sem)

Fix this by changing input parameter @nested of the schedule_erase() to
'true' to avoid recursively acquiring the down_read(&ubi->work_sem).

Also, fix the incorrect comment about @nested parameter of the
schedule_erase() because when down_write(ubi->work_sem) is held, the
@nested is also need be true.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217093
Fixes: 2e8f08deabbc ("ubi: Fix races around ubi_refill_pools()")
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ubi: Fix failure attaching when vid_hdr offset equals to (sub)page size

commit 1e020e1b96afdecd20680b5b5be2a6ffc3d27628 upstream.

Following process will make ubi attaching failed since commit
1b42b1a36fc946 ("ubi: ensure that VID header offset ... size"):

ID="0xec,0xa1,0x00,0x15" # 128M 128KB 2KB
modprobe nandsim id_bytes=$ID
flash_eraseall /dev/mtd0
modprobe ubi mtd="0,2048"  # set vid_hdr offset as 2048 (one page)
(dmesg):
  ubi0 error: ubi_attach_mtd_dev [ubi]: VID header offset 2048 too large.
  UBI error: cannot attach mtd0
  UBI error: cannot initialize UBI, error -22

Rework original solution, the key point is making sure
'vid_hdr_shift + UBI_VID_HDR_SIZE < ubi->vid_hdr_alsize',
so we should check vid_hdr_shift rather not vid_hdr_offset.
Then, ubi still support (sub)page aligined VID header offset.

Fixes: 1b42b1a36fc946 ("ubi: ensure that VID header offset ... size")
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com> # v5.10, v4.19
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mptcp: stricter state check in mptcp_worker

commit d6a0443733434408f2cbd4c53fea6910599bab9e upstream.

As reported by Christoph, the mptcp protocol can run the
worker when the relevant msk socket is in an unexpected state:

connect()
// incoming reset + fastclose
// the mptcp worker is scheduled
mptcp_disconnect()
// msk is now CLOSED
listen()
mptcp_worker()

Leading to the following splat:

divide error: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 21 Comm: kworker/1:0 Not tainted 6.3.0-rc1-gde5e8fd0123c #11
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
Workqueue: events mptcp_worker
RIP: 0010:__tcp_select_window+0x22c/0x4b0 net/ipv4/tcp_output.c:3018
RSP: 0018:ffffc900000b3c98 EFLAGS: 00010293
RAX: 000000000000ffd7 RBX: 000000000000ffd7 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8214ce97 RDI: 0000000000000004
RBP: 000000000000ffd7 R08: 0000000000000004 R09: 0000000000010000
R10: 000000000000ffd7 R11: ffff888005afa148 R12: 000000000000ffd7
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffff88803ed00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000405270 CR3: 000000003011e006 CR4: 0000000000370ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 <TASK>
 tcp_select_window net/ipv4/tcp_output.c:262 [inline]
 __tcp_transmit_skb+0x356/0x1280 net/ipv4/tcp_output.c:1345
 tcp_transmit_skb net/ipv4/tcp_output.c:1417 [inline]
 tcp_send_active_reset+0x13e/0x320 net/ipv4/tcp_output.c:3459
 mptcp_check_fastclose net/mptcp/protocol.c:2530 [inline]
 mptcp_worker+0x6c7/0x800 net/mptcp/protocol.c:2705
 process_one_work+0x3bd/0x950 kernel/workqueue.c:2390
 worker_thread+0x5b/0x610 kernel/workqueue.c:2537
 kthread+0x138/0x170 kernel/kthread.c:376
 ret_from_fork+0x2c/0x50 arch/x86/entry/entry_64.S:308
 </TASK>

This change addresses the issue explicitly checking for bad states
before running the mptcp worker.

Fixes: e16163b6e2b7 ("mptcp: refactor shutdown and close")
Cc: stable@vger.kernel.org
Reported-by: Christoph Paasch <cpaasch@apple.com>
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/374
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mptcp: use mptcp_schedule_work instead of open-coding it

commit a5cb752b125766524c921faab1a45cc96065b0a7 upstream.

Beyond reducing code duplication this also avoids scheduling
the mptcp_worker on a closed socket on some edge scenarios.

The addressed issue is actually older than the blamed commit
below, but this fix needs it as a pre-requisite.

Fixes: ba8f48f7a4d7 ("mptcp: introduce mptcp_schedule_work")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: correct SMU13.0.7 max shader clock reporting

commit 85e0689eb6b10cd3b2fb455d1b3f4d4d0b13ff78 upstream.

Correct the max shader clock reporting on SMU
13.0.7.

Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/pm: correct SMU13.0.7 pstate profiling clock settings

commit f06b8887e3ef4f50098d3a949aef392c529c831a upstream.

Correct the pstate standard/peak profiling mode clock
settings for SMU13.0.7.

Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup/cpuset: Wake up cpuset_attach_wq tasks in cpuset_cancel_attach()

commit ba9182a89626d5f83c2ee4594f55cb9c1e60f0e2 upstream.

After a successful cpuset_can_attach() call which increments the
attach_in_progress flag, either cpuset_cancel_attach() or cpuset_attach()
will be called later. In cpuset_attach(), tasks in cpuset_attach_wq,
if present, will be woken up at the end. That is not the case in
cpuset_cancel_attach(). So missed wakeup is possible if the attach
operation is somehow cancelled. Fix that by doing the wakeup in
cpuset_cancel_attach() as well.

Fixes: e44193d39e8d ("cpuset: let hotplug propagation work wait for task attaching")
Signed-off-by: Waiman Long <longman@redhat.com>
Reviewed-by: Michal Koutný <mkoutny@suse.com>
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup/cpuset: Fix partition root's cpuset.cpus update bug

commit 292fd843de26c551856e66faf134512c52dd78b4 upstream.

It was found that commit 7a2127e66a00 ("cpuset: Call
set_cpus_allowed_ptr() with appropriate mask for task") introduced a bug
that corrupted "cpuset.cpus" of a partition root when it was updated.

It is because the tmp->new_cpus field of the passed tmp parameter
of update_parent_subparts_cpumask() should not be used at all as
it contains important cpumask data that should not be overwritten.
Fix it by using tmp->addmask instead.

Also update update_cpumask() to make sure that trialcs->cpu_allowed
will not be corrupted until it is no longer needed.

Fixes: 7a2127e66a00 ("cpuset: Call set_cpus_allowed_ptr() with appropriate mask for task")
Signed-off-by: Waiman Long <longman@redhat.com>
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cgroup: fix display of forceidle time at root

commit fcdb1eda5302599045bb366e679cccb4216f3873 upstream.

We need to reset forceidle_sum to 0 when reading from root, since the
bstat we accumulate into is stack allocated.

To make this more robust, just replace the existing cputime reset with a
memset of the overall bstat.

Signed-off-by: Josh Don <joshdon@google.com>
Fixes: 1fcf54deb767 ("sched/core: add forced idle accounting for cgroups")
Cc: stable@vger.kernel.org # v6.0+
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/PCI: Add quirk for AMD XHCI controller that loses MSI-X state in D3hot

commit f195fc1e9715ba826c3b62d58038f760f66a4fe9 upstream.

The AMD [1022:15b8] USB controller loses some internal functional MSI-X
context when transitioning from D0 to D3hot. BIOS normally traps D0->D3hot
and D3hot->D0 transitions so it can save and restore that internal context,
but some firmware in the field can't do this because it fails to clear the
AMD_15B8_RCC_DEV2_EPF0_STRAP2 NO_SOFT_RESET bit.

Clear AMD_15B8_RCC_DEV2_EPF0_STRAP2 NO_SOFT_RESET bit before USB controller
initialization during boot.

Link: https://lore.kernel.org/linux-usb/Y%2Fz9GdHjPyF2rNG3@glanzmann.de/T/#u
Link: https://lore.kernel.org/r/20230329172859.699743-1-Basavaraj.Natikar@amd.com
Reported-by: Thomas Glanzmann <thomas@glanzmann.de>
Tested-by: Thomas Glanzmann <thomas@glanzmann.de>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ses: Handle enclosure with just a primary component gracefully

commit c8e22b7a1694bb8d025ea636816472739d859145 upstream.

This reverts commit 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure
has no components") and introduces proper handling of case where there are
no detected secondary components, but primary component (enumerated in
num_enclosures) does exist. That fix was originally proposed by Ding Hui
<dinghui@sangfor.com.cn>.

Completely ignoring devices that have one primary enclosure and no
secondary one results in ses_intf_add() bailing completely

scsi 2:0:0:254: enclosure has no enumerated components
        scsi 2:0:0:254: Failed to bind enclosure -12ven in valid configurations such

even on valid configurations with 1 primary and 0 secondary enclosures as
below:

# sg_ses /dev/sg0
  3PARdata  SES               3321
Supported diagnostic pages:
  Supported Diagnostic Pages [sdp] [0x0]
  Configuration (SES) [cf] [0x1]
  Short Enclosure Status (SES) [ses] [0x8]
# sg_ses -p cf /dev/sg0
  3PARdata  SES               3321
Configuration diagnostic page:
  number of secondary subenclosures: 0
  generation code: 0x0
  enclosure descriptor list
    Subenclosure identifier: 0 [primary]
      relative ES process id: 0, number of ES processes: 1
      number of type descriptor headers: 1
      enclosure logical identifier (hex): 20000002ac02068d
      enclosure vendor: 3PARdata  product: VV                rev: 3321
  type descriptor header and text list
    Element type: Unspecified, subenclosure id: 0
      number of possible elements: 1

The changelog for the original fix follows

=====
We can get a crash when disconnecting the iSCSI session,
the call trace like this:

  [ffff00002a00fb70] kfree at ffff00000830e224
  [ffff00002a00fba0] ses_intf_remove at ffff000001f200e4
  [ffff00002a00fbd0] device_del at ffff0000086b6a98
  [ffff00002a00fc50] device_unregister at ffff0000086b6d58
  [ffff00002a00fc70] __scsi_remove_device at ffff00000870608c
  [ffff00002a00fca0] scsi_remove_device at ffff000008706134
  [ffff00002a00fcc0] __scsi_remove_target at ffff0000087062e4
  [ffff00002a00fd10] scsi_remove_target at ffff0000087064c0
  [ffff00002a00fd70] __iscsi_unbind_session at ffff000001c872c4
  [ffff00002a00fdb0] process_one_work at ffff00000810f35c
  [ffff00002a00fe00] worker_thread at ffff00000810f648
  [ffff00002a00fe70] kthread at ffff000008116e98

In ses_intf_add, components count could be 0, and kcalloc 0 size scomp,
but not saved in edev->component[i].scratch

In this situation, edev->component[0].scratch is an invalid pointer,
when kfree it in ses_intf_remove_enclosure, a crash like above would happen
The call trace also could be other random cases when kfree cannot catch
the invalid pointer

We should not use edev->component[] array when the components count is 0
We also need check index when use edev->component[] array in
ses_enclosure_data_process
=====

Reported-by: Michal Kolar <mich.k@seznam.cz>
Originally-by: Ding Hui <dinghui@sangfor.com.cn>
Cc: stable@vger.kernel.org
Fixes: 3fe97ff3d949 ("scsi: ses: Don't attach if enclosure has no components")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2304042122270.29760@cbobk.fhfr.pm
Tested-by: Michal Kolar <mich.k@seznam.cz>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: nxp-c45-tja11xx: fix unsigned long multiplication overflow

commit bdaaecc127d471c422ee9e994978617c8aa79e1e upstream.

Any multiplication between GENMASK(31, 0) and a number bigger than 1
will be truncated because of the overflow, if the size of unsigned long
is 32 bits.

Replaced GENMASK with GENMASK_ULL to make sure that multiplication will
be between 64 bits values.

Cc: <stable@vger.kernel.org> # 5.15+
Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095953.75622-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: phy: nxp-c45-tja11xx: add remove callback

commit a4506722dc39ca840593f14e3faa4c9ba9408211 upstream.

Unregister PTP clock when the driver is removed.
Purge the RX and TX skb queues.

Fixes: 514def5dd339 ("phy: nxp-c45-tja11xx: add timestamping support")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230406095904.75456-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sfp: initialize sfp->i2c_block_size at sfp allocation

commit 813c2dd78618f108fdcf9cd726ea90f081ee2881 upstream.

sfp->i2c_block_size is initialized at SFP module insertion in
sfp_sm_mod_probe(). Because of that, if SFP module was never inserted
since boot, sfp_read() call will lead to zero-length I2C read attempt,
and not all I2C controllers are happy with zero-length reads.

One way to issue sfp_read() on empty SFP cage is to execute ethtool -m.
If SFP module was never plugged since boot, there will be a zero-length
I2C read attempt.

  # ethtool -m xge0
  i2c i2c-3: adapter quirk: no zero length (addr 0x0050, size 0, read)
  Cannot get Module EEPROM data: Operation not supported

If SFP module was plugged then removed at least once,
sfp->i2c_block_size will be initialized and ethtool -m will fail with
different exit code and without I2C error

  # ethtool -m xge0
  Cannot get Module EEPROM data: Remote I/O error

Fix this by initializing sfp->i2_block_size at struct sfp allocation
stage so no wild sfp_read() could issue zero-length I2C read.

Signed-off-by: Ivan Bornyakov <i.bornyakov@metrotek.ru>
Fixes: 0d035bed2a4a ("net: sfp: VSOL V2801F / CarlitoxxPro CPGOS03-0490 v2.0 workaround")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: intel-ish-hid: Fix kernel panic during warm reset

commit 38518593ec55e897abda4b4be77b2ec8ec4447d1 upstream.

During warm reset device->fw_client is set to NULL. If a bus driver is
registered after this NULL setting and before new firmware clients are
enumerated by ISHTP, kernel panic will result in the function
ishtp_cl_bus_match(). This is because of reference to
device->fw_client->props.protocol_name.

ISH firmware after getting successfully loaded, sends a warm reset
notification to remove all clients from the bus and sets
device->fw_client to NULL. Until kernel v5.15, all enabled ISHTP kernel
module drivers were loaded right after any of the first ISHTP device was
registered, regardless of whether it was a matched or an unmatched
device. This resulted in all drivers getting registered much before the
warm reset notification from ISH.

Starting kernel v5.16, this issue got exposed after the change was
introduced to load only bus drivers for the respective matching devices.
In this scenario, cros_ec_ishtp device and cros_ec_ishtp driver are
registered after the warm reset device fw_client NULL setting.
cros_ec_ishtp driver_register() triggers the callback to
ishtp_cl_bus_match() to match ISHTP driver to the device and causes kernel
panic in guid_equal() when dereferencing fw_client NULL pointer to get
protocol_name.

Fixes: f155dfeaa4ee ("platform/x86: isthp_eclite: only load for matching devices")
Fixes: facfe0a4fdce ("platform/chrome: chros_ec_ishtp: only load for matching devices")
Fixes: 0d0cccc0fd83 ("HID: intel-ish-hid: hid-client: only load for matching devices")
Fixes: 44e2a58cb880 ("HID: intel-ish-hid: fw-loader: only load for matching devices")
Cc: <stable@vger.kernel.org> # 5.16+
Signed-off-by: Tanu Malhotra <tanu.malhotra@intel.com>
Tested-by: Shaunak Saha <shaunak.saha@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

riscv: add icache flush for nommu sigreturn trampoline

commit 8d736482749f6d350892ef83a7a11d43cd49981e upstream.

In a NOMMU kernel, sigreturn trampolines are generated on the user
stack by setup_rt_frame. Currently, these trampolines are not instruction
fenced, thus their visibility to ifetch is not guaranteed.

This patch adds a flush_icache_range in setup_rt_frame to fix this
problem.

Signed-off-by: Mathis Salmen <mathis.salmen@matsal.de>
Fixes: 6bd33e1ece52 ("riscv: add nommu support")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230406101130.82304-1-mathis.salmen@matsal.de
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ksmbd: avoid out of bounds access in decode_preauth_ctxt()

commit e7067a446264a7514fa1cfaa4052cdb6803bc6a2 upstream.

Confirm that the accessed pneg_ctxt->HashAlgorithms address sits within
the SMB request boundary; deassemble_neg_contexts() only checks that the
eight byte smb2_neg_context header + (client controlled) DataLength are
within the packet boundary, which is insufficient.

Checking for sizeof(struct smb2_preauth_neg_context) is overkill given
that the type currently assumes SMB311_SALT_SIZE bytes of trailing Salt.

Signed-off-by: David Disseldorp <ddiss@suse.de>
Acked-by: Namjae Jeon <linkinjeon@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

maple_tree: fix write memory barrier of nodes once dead for RCU mode

[ Upstream commit c13af03de46ba27674dd9fb31a17c0d480081139 ]

During the development of the maple tree, the strategy of freeing multiple
nodes changed and, in the process, the pivots were reused to store
pointers to dead nodes.  To ensure the readers see accurate pivots, the
writers need to mark the nodes as dead and call smp_wmb() to ensure any
readers can identify the node as dead before using the pivot values.

There were two places where the old method of marking the node as dead
without smp_wmb() were being used, which resulted in RCU readers seeing
the wrong pivot value before seeing the node was dead.  Fix this race
condition by using mte_set_node_dead() which has the smp_wmb() call to
ensure the race is closed.

Add a WARN_ON() to the ma_free_rcu() call to ensure all nodes being freed
are marked as dead to ensure there are no other call paths besides the two
updated paths.

This is necessary for the RCU mode of the maple tree.

Link: https://lkml.kernel.org/r/20230227173632.3292573-6-surenb@google.com
Fixes: 54a611b60590 ("Maple Tree: add new data structure")
Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Have tracing_snapshot_instance_cond() write errors to the appropriate instance

[ Upstream commit 9d52727f8043cfda241ae96896628d92fa9c50bb ]

If a trace instance has a failure with its snapshot code, the error
message is to be written to that instance's buffer. But currently, the
message is written to the top level buffer. Worse yet, it may also disable
the top level buffer and not the instance that had the issue.

Link: https://lkml.kernel.org/r/20230405022341.688730321@goodmis.org
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ross Zwisler <zwisler@google.com>
Fixes: 2824f50332486 ("tracing: Make the snapshot trigger work with instances")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Add trace_array_puts() to write into instance

[ Upstream commit d503b8f7474fe7ac616518f7fc49773cbab49f36 ]

Add a generic trace_array_puts() that can be used to "trace_puts()" into
an allocated trace_array instance. This is just another variant of
trace_array_printk().

Link: https://lkml.kernel.org/r/20230207173026.584717290@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Stable-dep-of: 9d52727f8043 ("tracing: Have tracing_snapshot_instance_cond() write errors to the appropriate instance")
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: SVM: Flush Hyper-V TLB when required

[ Upstream commit e5c972c1fadacc858b6a564d056f177275238040 ]

The Hyper-V "EnlightenedNptTlb" enlightenment is always enabled when KVM
is running on top of Hyper-V and Hyper-V exposes support for it (which
is always). On AMD CPUs this enlightenment results in ASID invalidations
not flushing TLB entries derived from the NPT. To force the underlying
(L0) hypervisor to rebuild its shadow page tables, an explicit hypercall
is needed.

The original KVM implementation of Hyper-V's "EnlightenedNptTlb" on SVM
only added remote TLB flush hooks. This worked out fine for a while, as
sufficient remote TLB flushes where being issued in KVM to mask the
problem. Since v5.17, changes in the TDP code reduced the number of
flushes and the out-of-sync TLB prevents guests from booting
successfully.

Split svm_flush_tlb_current() into separate callbacks for the 3 cases
(guest/all/current), and issue the required Hyper-V hypercall when a
Hyper-V TLB flush is needed. The most important case where the TLB flush
was missing is when loading a new PGD, which is followed by what is now
svm_flush_tlb_current().

Cc: stable@vger.kernel.org # v5.17+
Fixes: 1e0c7d40758b ("KVM: SVM: hyper-v: Remote TLB flush for SVM")
Link: https://lore.kernel.org/lkml/43980946-7bbf-dcef-7e40-af904c456250@linux.microsoft.com/
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Jeremi Piotrowski <jpiotrowski@linux.microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20230324145233.4585-1-jpiotrowski@linux.microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/hyperv: KVM: Rename "hv_enlightenments" to "hv_vmcb_enlightenments"

[ Upstream commit 26b516bb39215cf60aa1fb55d0a6fd73058698fa ]

Now that KVM isn't littered with "struct hv_enlightenments" casts, rename
the struct to "hv_vmcb_enlightenments" to highlight the fact that the
struct is specifically for SVM's VMCB.

No functional change intended.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-5-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: e5c972c1fada ("KVM: SVM: Flush Hyper-V TLB when required")
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: SVM: Add a proper field for Hyper-V VMCB enlightenments

[ Upstream commit 68ae7c7bc56a4504ed5efde7c2f8d6024148a35e ]

Add a union to provide hv_enlightenments side-by-side with the sw_reserved
bytes that Hyper-V's enlightenments overlay.  Casting sw_reserved
everywhere is messy, confusing, and unnecessarily unsafe.

No functional change intended.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: e5c972c1fada ("KVM: SVM: Flush Hyper-V TLB when required")
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: selftests: Move "struct hv_enlightenments" to x86_64/svm.h

[ Upstream commit 381fc63ac0754e05d3921e9d399b89dfdfd2b2e5 ]

Move Hyper-V's VMCB "struct hv_enlightenments" to the svm.h header so
that the struct can be referenced in "struct vmcb_control_area".
Alternatively, a dedicated header for SVM+Hyper-V could be added, a la
x86_64/evmcs.h, but it doesn't appear that Hyper-V will end up needing
a wholesale replacement for the VMCB.

No functional change intended.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: e5c972c1fada ("KVM: SVM: Flush Hyper-V TLB when required")
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/hyperv: Move VMCB enlightenment definitions to hyperv-tlfs.h

[ Upstream commit 089fe572a2e0a89e36a455d299d801770293d08f ]

Move Hyper-V's VMCB enlightenment definitions to the TLFS header; the
definitions come directly from the TLFS[*], not from KVM.

No functional change intended.

[*] https://learn.microsoft.com/en-us/virtualization/hyper-v-on-windows/tlfs/datatypes/hv_svm_enlightened_vmcb_fields

[vitaly: rename VMCB_HV_ -> HV_VMCB_ to match the rest of
hyperv-tlfs.h, keep svm/hyperv.h]

Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20221101145426.251680-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Stable-dep-of: e5c972c1fada ("KVM: SVM: Flush Hyper-V TLB when required")
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: resource: Add Medion S17413 to IRQ override quirk

[ Upstream commit 2d0ab14634a26e54f8d6d231b47b7ef233e84599 ]

Add DMI info of the Medion S17413 (board M1xA) to the IRQ override
quirk table. This fixes the keyboard not working on these laptops.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=213031
Signed-off-by: Aymeric Wibo <obiwac@gmail.com>
[ rjw: Fixed up white space ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu/gfx: set cg flags to enter/exit safe mode

[ Upstream commit e06bfcc1a1c41bcb8c31470d437e147ce9f0acfd ]

sriov needs to enter/exit safe mode in update umd p state
add the cg flag to let it enter or exit while needed

Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Force signal hw_fences that are embedded in non-sched jobs

[ Upstream commit 033c56474acf567a450f8bafca50e0b610f2b716 ]

[Why]
For engines not supporting soft reset, i.e. VCN, there will be a failed
ib test before mode 1 reset during asic reset. The fences in this case
are never signaled and next time when we try to free the sa_bo, kernel
will hang.

[How]
During pre_asic_reset, driver will clear job fences and afterwards the
fences' refcount will be reduced to 1. For drm_sched_jobs it will be
released in job_free_cb, and for non-sched jobs like ib_test, it's meant
to be released in sa_bo_free but only when the fences are signaled. So
we have to force signal the non_sched bad job's fence during
pre_asic_reset or the clear is not complete.

Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: add mes resume when do gfx post soft reset

[ Upstream commit 4eb0b49a0ad3e004a6a65b84efe37bc7e66d560f ]

[why]
when gfx do soft reset, mes will also do reset, if mes is not
resumed when do recover from soft reset, mes is unable to respond
in later sequence

[how]
resume mes when do gfx post soft reset

Signed-off-by: Tong Liu01 <Tong.Liu01@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: mvm: protect TXQ list manipulation

[ Upstream commit 923bf981eb6ecc027227716e30701bdcc1845fbf ]

Some recent upstream debugging uncovered the fact that in
iwlwifi, the TXQ list manipulation is racy.

Introduce a new state bit for when the TXQ is completely
ready and can be used without locking, and if that's not
set yet acquire the lock to check everything correctly.

Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: mvm: fix mvmtxq->stopped handling

[ Upstream commit b58e3d4311b54b6dd0e37165277965da0c9eb21d ]

This could race if the queue is redirected while full, then
the flushing internally would start it while it's not yet
usable again. Fix it by using two state bits instead of just
one.

Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Tested-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: send Identify with CNS 06h only to I/O controllers

[ Upstream commit def84ab600b71ea3fcc422a876d5d0d0daa7d4f3 ]

Identify CNS 06h (I/O Command Set Specific Identify Controller data
structure) is supported only on i/o controllers.

But nvme_init_non_mdts_limits() currently invokes this on all
controllers.  Correct this by ensuring this is sent to I/O
controllers only.

Signed-off-by: Martin George <marting@netapp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

asymmetric_keys: log on fatal failures in PE/pkcs7

[ Upstream commit 3584c1dbfffdabf8e3dc1dd25748bb38dd01cd43 ]

These particular errors can be encountered while trying to kexec when
secureboot lockdown is in place.  Without this change, even with a
signed debug build, one still needs to reboot the machine to add the
appropriate dyndbg parameters (since lockdown blocks debugfs).

Accordingly, upgrade all pr_debug() before fatal error into pr_warn().

Signed-off-by: Robbie Harwood <rharwood@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jarkko Sakkinen <jarkko@kernel.org>
cc: Eric Biederman <ebiederm@xmission.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: keyrings@vger.kernel.org
cc: linux-crypto@vger.kernel.org
cc: kexec@lists.infradead.org
Link: https://lore.kernel.org/r/20230220171254.592347-3-rharwood@redhat.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>

verify_pefile: relax wrapper length check

[ Upstream commit 4fc5c74dde69a7eda172514aaeb5a7df3600adb3 ]

The PE Format Specification (section "The Attribute Certificate Table
(Image Only)") states that `dwLength` is to be rounded up to 8-byte
alignment when used for traversal.  Therefore, the field is not required
to be an 8-byte multiple in the first place.

Accordingly, pesign has not performed this alignment since version
0.110.  This causes kexec failure on pesign'd binaries with "PEFILE:
Signature wrapper len wrong".  Update the comment and relax the check.

Signed-off-by: Robbie Harwood <rharwood@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jarkko Sakkinen <jarkko@kernel.org>
cc: Eric Biederman <ebiederm@xmission.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: keyrings@vger.kernel.org
cc: linux-crypto@vger.kernel.org
cc: kexec@lists.infradead.org
Link: https://learn.microsoft.com/en-us/windows/win32/debug/pe-format#the-attribute-certificate-table-image-only
Link: https://github.com/rhboot/pesign
Link: https://lore.kernel.org/r/20230220171254.592347-2-rharwood@redhat.com/
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (xgene) Fix ioremap and memremap leak

[ Upstream commit 813cc94c7847ae4a17e9f744fb4dbdf7df6bd732 ]

Smatch reports:

drivers/hwmon/xgene-hwmon.c:757 xgene_hwmon_probe() warn:
'ctx->pcc_comm_addr' from ioremap() not released on line: 757.

This is because in drivers/hwmon/xgene-hwmon.c:701 xgene_hwmon_probe(),
ioremap and memremap is not released, which may cause a leak.

To fix this, ioremap and memremap is modified to devm_ioremap and
devm_memremap.

Signed-off-by: Tianyi Jing <jingfelix@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230318143851.2191625-1-jingfelix@hust.edu.cn
[groeck: Fixed formatting and subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (peci/cputemp) Fix miscalculated DTS for SKX

[ Upstream commit 2b91c4a870c9830eaf95e744454c9c218cccb736 ]

For Skylake, DTS temperature of the CPU is reported in S10.6 format
instead of S8.8.

Reported-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/lkml/ZBhHS7v+98NK56is@home.paul.comp/
Signed-off-by: Iwona Winiarska <iwona.winiarska@intel.com>
Link: https://lore.kernel.org/r/20230321090410.866766-1-iwona.winiarska@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm: panel-orientation-quirks: Add quirk for Lenovo Yoga Book X90F

[ Upstream commit 03aecb1acbcd7a660f97d645ca6c09d9de27ff9d ]

Like the Windows Lenovo Yoga Book X91F/L the Android Lenovo Yoga Book
X90F/L has a portrait 1200x1920 screen used in landscape mode,
add a quirk for this.

When the quirk for the X91F/L was initially added it was written to
also apply to the X90F/L but this does not work because the Android
version of the Yoga Book uses completely different DMI strings.
Also adjust the X91F/L quirk to reflect that it only applies to
the X91F/L models.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230301095218.28457-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: video: Add backlight=native DMI quirk for Acer Aspire 3830TG

[ Upstream commit 5e7a3bf65db57461d0f47955248fcadf37321a74 ]

The Acer Aspire 3830TG predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.

Add a DMI quirk to use the native backlight interface which does
work properly.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: ublk_drv: mark device as LIVE before adding disk

[ Upstream commit 4985e7b2c002eb4c5c794a1d3acd91b82c89a0fd ]

IO can be started before add_disk() returns, such as reading parititon table,
then the monitor work should work for making forward progress.

So mark device as LIVE before adding disk, meantime change to
DEAD if add_disk() fails.

Fixed: 71f28f3136af ("ublk_drv: add io_uring based userspace block driver")
Reviewed-by: Ziyang Zhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20230318141231.55562-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

efi: sysfb_efi: Add quirk for Lenovo Yoga Book X91F/L

[ Upstream commit 5ed213dd64681f84a01ceaa82fb336cf7d59ddcf ]

Another Lenovo convertable which reports a landscape resolution of
1920x1200 with a pitch of (1920 * 4) bytes, while the actual framebuffer
has a resolution of 1200x1920 with a pitch of (1200 * 4) bytes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: hisi: Avoid redundant interrupts

[ Upstream commit cc9812a3096d1986caca9a23bee99effc45c08df ]

After issuing all the messages we can disable the TX_EMPTY interrupts
to avoid handling redundant interrupts. For doing a sinlge bus
detection (i2cdetect -y -r 0) we can reduce ~97% interrupts (before
~12000 after ~400).

Signed-off-by: Sheng Feng <fengsheng5@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: imx-lpi2c: clean rx/tx buffers upon new message

[ Upstream commit 987dd36c0141f6ab9f0fbf14d6b2ec3342dedb2f ]

When start sending a new message clear the Rx & Tx buffer pointers in
order to avoid using stale pointers.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Tested-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: mwifiex: mark OF related data as maybe unused

[ Upstream commit 139f6973bf140c65d4d1d4bde5485badb4454d7a ]

The driver can be compile tested with !CONFIG_OF making certain data
unused:

  drivers/net/wireless/marvell/mwifiex/sdio.c:498:34: error: ‘mwifiex_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=]
  drivers/net/wireless/marvell/mwifiex/pcie.c:175:34: error: ‘mwifiex_pcie_of_match_table’ defined but not used [-Werror=unused-const-variable=]

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230312132523.352182-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/bpf: Fix progs/find_vma_fail1.c build error.

[ Upstream commit 32513d40d908b267508d37994753d9bd1600914b ]

The commit 11e456cae91e ("selftests/bpf: Fix compilation errors: Assign a value to a constant")
fixed the issue cleanly in bpf-next.
This is an alternative fix in bpf tree to avoid merge conflict between bpf and bpf-next.

Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: axp288_fuel_gauge: Added check for negative values

[ Upstream commit bf6c880d5d1448489ebf92e2d13d5713ff644930 ]

Variable 'pirq', which may receive negative value
in platform_get_irq().
Used as an index in a function regmap_irq_get_virq().

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Signed-off-by: Denis Arefev <arefev@swemel.ru>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: cros_usbpd: reclassify "default case!" as debug

[ Upstream commit 14c76b2e75bca4d96e2b85a0c12aa43e84fe3f74 ]

This doesn't need to be printed every second as an error:
...
<3>[17438.628385] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17439.634176] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
<3>[17440.640298] cros-usbpd-charger cros-usbpd-charger.3.auto: Port 1: default case!
...

Reduce priority from ERROR to DEBUG.

Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

power: supply: rk817: Fix unsigned comparison with less than zero

[ Upstream commit 3268a4d9b0b85a4382e93bdf7be5400a73db74c5 ]

The tmp is defined as u32 type, which results in invalid processing of
tmp<0 in function rk817_read_or_set_full_charge_on_boot(). Therefore,
drop the comparison.

drivers/power/supply/rk817_charger.c:828 rk817_read_or_set_full_charge_on_boot() warn: unsigned 'tmp' is never less than zero.
drivers/power/supply/rk817_charger.c:788 rk817_read_or_set_full_charge_on_boot() warn: unsigned 'tmp' is never less than zero.

Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3444
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: qcom: apq8026-lg-lenok: add missing reserved memory

[ Upstream commit ecd240875e877d78fd03efbc62292f550872df3f ]

Turns out these two memory regions also need to be avoided, otherwise
weird things will happen when Linux tries to use this memory.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308-lenok-reserved-memory-v1-1-b8bf6ff01207@z3ntu.xyz
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 9290/1: uaccess: Fix KASAN false-positives

[ Upstream commit ceac10c83b330680cc01ceaaab86cd49f4f30d81 ]

__copy_to_user_memcpy() and __clear_user_memset() had been calling
memcpy() and memset() respectively, leading to false-positive KASAN
reports when starting userspace:

    [   10.707901] Run /init as init process
    [   10.731892] process '/bin/busybox' started with executable stack
    [   10.745234] ==================================================================
    [   10.745796] BUG: KASAN: user-memory-access in __clear_user_memset+0x258/0x3ac
    [   10.747260] Write of size 2687 at addr 000de581 by task init/1

Use __memcpy() and __memset() instead to allow userspace access, which
is of course the intent of these functions.

Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

libbpf: Fix single-line struct definition output in btf_dump

[ Upstream commit 872aec4b5f635d94111d48ec3c57fbe078d64e7d ]

btf_dump APIs emit unnecessary tabs when emitting struct/union
definition that fits on the single line. Before this patch we'd get:

struct blah {<tab>};

This patch fixes this and makes sure that we get more natural:

struct blah {};

Fixes: 44a726c3f23c ("bpftool: Print newline before '}' for struct with padding only fields")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20221212211505.558851-2-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

skbuff: Fix a race between coalescing and releasing SKBs

[ Upstream commit 0646dc31ca886693274df5749cd0c8c1eaaeb5ca ]

Commit 1effe8ca4e34 ("skbuff: fix coalescing for page_pool fragment
recycling") allowed coalescing to proceed with non page pool page and page
pool page when @from is cloned, i.e.

to->pp_recycle    --> false
from->pp_recycle  --> true
skb_cloned(from)  --> true

However, it actually requires skb_cloned(@from) to hold true until
coalescing finishes in this situation. If the other cloned SKB is
released while the merging is in process, from_shinfo->nr_frags will be
set to 0 toward the end of the function, causing the increment of frag
page _refcount to be unexpectedly skipped resulting in inconsistent
reference counts. Later when SKB(@to) is released, it frees the page
directly even though the page pool page is still in use, leading to
use-after-free or double-free errors. So it should be prohibited.

The double-free error message below prompted us to investigate:
BUG: Bad page state in process swapper/1  pfn:0e0d1
page:00000000c6548b28 refcount:-1 mapcount:0 mapping:0000000000000000
index:0x2 pfn:0xe0d1
flags: 0xfffffc0000000(node=0|zone=1|lastcpupid=0x1fffff)
raw: 000fffffc0000000 0000000000000000 ffffffff00000101 0000000000000000
raw: 0000000000000002 0000000000000000 ffffffffffffffff 0000000000000000
page dumped because: nonzero _refcount

CPU: 1 PID: 0 Comm: swapper/1 Tainted: G            E      6.2.0+
Call Trace:
 <IRQ>
dump_stack_lvl+0x32/0x50
bad_page+0x69/0xf0
free_pcp_prepare+0x260/0x2f0
free_unref_page+0x20/0x1c0
skb_release_data+0x10b/0x1a0
napi_consume_skb+0x56/0x150
net_rx_action+0xf0/0x350
? __napi_schedule+0x79/0x90
__do_softirq+0xc8/0x2b1
__irq_exit_rcu+0xb9/0xf0
common_interrupt+0x82/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:default_idle+0xb/0x20

Fixes: 53e0961da1c7 ("page_pool: add frag page recycling support in page pool")
Signed-off-by: Liang Chen <liangchen.linux@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230413090353.14448-1-liangchen.linux@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: macb: fix a memory corruption in extended buffer descriptor mode

[ Upstream commit e8b74453555872851bdd7ea43a7c0ec39659834f ]

For quite some time we were chasing a bug which looked like a sudden
permanent failure of networking and mmc on some of our devices.
The bug was very sensitive to any software changes and even more to
any kernel debug options.

Finally we got a setup where the problem was reproducible with
CONFIG_DMA_API_DEBUG=y and it revealed the issue with the rx dma:

[   16.992082] ------------[ cut here ]------------
[   16.996779] DMA-API: macb ff0b0000.ethernet: device driver tries to free DMA memory it has not allocated [device address=0x0000000875e3e244] [size=1536 bytes]
[   17.011049] WARNING: CPU: 0 PID: 85 at kernel/dma/debug.c:1011 check_unmap+0x6a0/0x900
[   17.018977] Modules linked in: xxxxx
[   17.038823] CPU: 0 PID: 85 Comm: irq/55-8000f000 Not tainted 5.4.0 #28
[   17.045345] Hardware name: xxxxx
[   17.049528] pstate: 60000005 (nZCv daif -PAN -UAO)
[   17.054322] pc : check_unmap+0x6a0/0x900
[   17.058243] lr : check_unmap+0x6a0/0x900
[   17.062163] sp : ffffffc010003c40
[   17.065470] x29: ffffffc010003c40 x28: 000000004000c03c
[   17.070783] x27: ffffffc010da7048 x26: ffffff8878e38800
[   17.076095] x25: ffffff8879d22810 x24: ffffffc010003cc8
[   17.081407] x23: 0000000000000000 x22: ffffffc010a08750
[   17.086719] x21: ffffff8878e3c7c0 x20: ffffffc010acb000
[   17.092032] x19: 0000000875e3e244 x18: 0000000000000010
[   17.097343] x17: 0000000000000000 x16: 0000000000000000
[   17.102647] x15: ffffff8879e4a988 x14: 0720072007200720
[   17.107959] x13: 0720072007200720 x12: 0720072007200720
[   17.113261] x11: 0720072007200720 x10: 0720072007200720
[   17.118565] x9 : 0720072007200720 x8 : 000000000000022d
[   17.123869] x7 : 0000000000000015 x6 : 0000000000000098
[   17.129173] x5 : 0000000000000000 x4 : 0000000000000000
[   17.134475] x3 : 00000000ffffffff x2 : ffffffc010a1d370
[   17.139778] x1 : b420c9d75d27bb00 x0 : 0000000000000000
[   17.145082] Call trace:
[   17.147524]  check_unmap+0x6a0/0x900
[   17.151091]  debug_dma_unmap_page+0x88/0x90
[   17.155266]  gem_rx+0x114/0x2f0
[   17.158396]  macb_poll+0x58/0x100
[   17.161705]  net_rx_action+0x118/0x400
[   17.165445]  __do_softirq+0x138/0x36c
[   17.169100]  irq_exit+0x98/0xc0
[   17.172234]  __handle_domain_irq+0x64/0xc0
[   17.176320]  gic_handle_irq+0x5c/0xc0
[   17.179974]  el1_irq+0xb8/0x140
[   17.183109]  xiic_process+0x5c/0xe30
[   17.186677]  irq_thread_fn+0x28/0x90
[   17.190244]  irq_thread+0x208/0x2a0
[   17.193724]  kthread+0x130/0x140
[   17.196945]  ret_from_fork+0x10/0x20
[   17.200510] ---[ end trace 7240980785f81d6f ]---

[  237.021490] ------------[ cut here ]------------
[  237.026129] DMA-API: exceeded 7 overlapping mappings of cacheline 0x0000000021d79e7b
[  237.033886] WARNING: CPU: 0 PID: 0 at kernel/dma/debug.c:499 add_dma_entry+0x214/0x240
[  237.041802] Modules linked in: xxxxx
[  237.061637] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W         5.4.0 #28
[  237.068941] Hardware name: xxxxx
[  237.073116] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[  237.077900] pc : add_dma_entry+0x214/0x240
[  237.081986] lr : add_dma_entry+0x214/0x240
[  237.086072] sp : ffffffc010003c30
[  237.089379] x29: ffffffc010003c30 x28: ffffff8878a0be00
[  237.094683] x27: 0000000000000180 x26: ffffff8878e387c0
[  237.099987] x25: 0000000000000002 x24: 0000000000000000
[  237.105290] x23: 000000000000003b x22: ffffffc010a0fa00
[  237.110594] x21: 0000000021d79e7b x20: ffffffc010abe600
[  237.115897] x19: 00000000ffffffef x18: 0000000000000010
[  237.121201] x17: 0000000000000000 x16: 0000000000000000
[  237.126504] x15: ffffffc010a0fdc8 x14: 0720072007200720
[  237.131807] x13: 0720072007200720 x12: 0720072007200720
[  237.137111] x11: 0720072007200720 x10: 0720072007200720
[  237.142415] x9 : 0720072007200720 x8 : 0000000000000259
[  237.147718] x7 : 0000000000000001 x6 : 0000000000000000
[  237.153022] x5 : ffffffc010003a20 x4 : 0000000000000001
[  237.158325] x3 : 0000000000000006 x2 : 0000000000000007
[  237.163628] x1 : 8ac721b3a7dc1c00 x0 : 0000000000000000
[  237.168932] Call trace:
[  237.171373]  add_dma_entry+0x214/0x240
[  237.175115]  debug_dma_map_page+0xf8/0x120
[  237.179203]  gem_rx_refill+0x190/0x280
[  237.182942]  gem_rx+0x224/0x2f0
[  237.186075]  macb_poll+0x58/0x100
[  237.189384]  net_rx_action+0x118/0x400
[  237.193125]  __do_softirq+0x138/0x36c
[  237.196780]  irq_exit+0x98/0xc0
[  237.199914]  __handle_domain_irq+0x64/0xc0
[  237.204000]  gic_handle_irq+0x5c/0xc0
[  237.207654]  el1_irq+0xb8/0x140
[  237.210789]  arch_cpu_idle+0x40/0x200
[  237.214444]  default_idle_call+0x18/0x30
[  237.218359]  do_idle+0x200/0x280
[  237.221578]  cpu_startup_entry+0x20/0x30
[  237.225493]  rest_init+0xe4/0xf0
[  237.228713]  arch_call_rest_init+0xc/0x14
[  237.232714]  start_kernel+0x47c/0x4a8
[  237.236367] ---[ end trace 7240980785f81d70 ]---

Lars was fast to find an explanation: according to the datasheet
bit 2 of the rx buffer descriptor entry has a different meaning in the
extended mode:
  Address [2] of beginning of buffer, or
  in extended buffer descriptor mode (DMA configuration register [28] = 1),
  indicates a valid timestamp in the buffer descriptor entry.

The macb driver didn't mask this bit while getting an address and it
eventually caused a memory corruption and a dma failure.

The problem is resolved by explicitly clearing the problematic bit
if hw timestamping is used.

Fixes: 7b4296148066 ("net: macb: Add support for PTP timestamps in DMA descriptors")
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Co-developed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230412232144.770336-1-roman.gushchin@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

udp6: fix potential access to stale information

[ Upstream commit 1c5950fc6fe996235f1d18539b9c6b64b597f50f ]

lena wang reported an issue caused by udpv6_sendmsg()
mangling msg->msg_name and msg->msg_namelen, which
are later read from ____sys_sendmsg() :

/*
 * If this is sendmmsg() and sending to current destination address was
 * successful, remember it.
 */
if (used_address && err >= 0) {
used_address->name_len = msg_sys->msg_namelen;
if (msg_sys->msg_name)
memcpy(&used_address->name, msg_sys->msg_name,
       used_address->name_len);
}

udpv6_sendmsg() wants to pretend the remote address family
is AF_INET in order to call udp_sendmsg().

A fix would be to modify the address in-place, instead
of using a local variable, but this could have other side effects.

Instead, restore initial values before we return from udpv6_sendmsg().

Fixes: c71d8ebe7a44 ("net: Fix security_socket_sendmsg() bypass problem.")
Reported-by: lena wang <lena.wang@mediatek.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20230412130308.1202254-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: openvswitch: adjust datapath NL message declaration

[ Upstream commit 306dc21361993f4fe50a15d4db6b1a4de5d0adb0 ]

The netlink message for creating a new datapath takes an array
of ports for the PID creation.  This shouldn't cause much issue
but correct it for future cases where we need to do decode of
datapath information that could include the per-cpu PID map.

Fixes: 25f16c873fb1 ("selftests: add openvswitch selftest suite")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20230412115828.3991806-1-aconole@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/core: Fix GID entry ref leak when create_ah fails

[ Upstream commit aca3b0fa3d04b40c96934d86cc224cccfa7ea8e0 ]

If AH create request fails, release sgid_attr to avoid GID entry
referrence leak reported while releasing GID table

Fixes: 1a1f460ff151 ("RDMA: Hold the sgid_attr inside the struct ib_ah/qp")
Link: https://lore.kernel.org/r/20230401063424.342204-1-saravanan.vajravel@broadcom.com
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sctp: fix a potential overflow in sctp_ifwdtsn_skip

[ Upstream commit 32832a2caf82663870126c5186cf8f86c8b2a649 ]

Currently, when traversing ifwdtsn skips with _sctp_walk_ifwdtsn, it only
checks the pos against the end of the chunk. However, the data left for
the last pos may be < sizeof(struct sctp_ifwdtsn_skip), and dereference
it as struct sctp_ifwdtsn_skip may cause coverflow.

This patch fixes it by checking the pos against "the end of the chunk -
sizeof(struct sctp_ifwdtsn_skip)" in sctp_ifwdtsn_skip, similar to
sctp_fwdtsn_skip.

Fixes: 0fc2ea922c8a ("sctp: implement validate_ftsn for sctp_stream_interleave")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/2a71bffcd80b4f2c61fac6d344bb2f11c8fd74f7.1681155810.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: qrtr: Fix an uninit variable access bug in qrtr_tx_resume()

[ Upstream commit 6417070918de3bcdbe0646e7256dae58fd8083ba ]

Syzbot reported a bug as following:

=====================================================
BUG: KMSAN: uninit-value in qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
 qrtr_tx_resume+0x185/0x1f0 net/qrtr/af_qrtr.c:230
 qrtr_endpoint_post+0xf85/0x11b0 net/qrtr/af_qrtr.c:519
 qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
 call_write_iter include/linux/fs.h:2189 [inline]
 aio_write+0x63a/0x950 fs/aio.c:1600
 io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
 __do_sys_io_submit fs/aio.c:2078 [inline]
 __se_sys_io_submit+0x293/0x770 fs/aio.c:2048
 __x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

Uninit was created at:
 slab_post_alloc_hook mm/slab.h:766 [inline]
 slab_alloc_node mm/slub.c:3452 [inline]
 __kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
 __do_kmalloc_node mm/slab_common.c:967 [inline]
 __kmalloc_node_track_caller+0x114/0x3b0 mm/slab_common.c:988
 kmalloc_reserve net/core/skbuff.c:492 [inline]
 __alloc_skb+0x3af/0x8f0 net/core/skbuff.c:565
 __netdev_alloc_skb+0x120/0x7d0 net/core/skbuff.c:630
 qrtr_endpoint_post+0xbd/0x11b0 net/qrtr/af_qrtr.c:446
 qrtr_tun_write_iter+0x270/0x400 net/qrtr/tun.c:108
 call_write_iter include/linux/fs.h:2189 [inline]
 aio_write+0x63a/0x950 fs/aio.c:1600
 io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
 __do_sys_io_submit fs/aio.c:2078 [inline]
 __se_sys_io_submit+0x293/0x770 fs/aio.c:2048
 __x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x63/0xcd

It is because that skb->len requires at least sizeof(struct qrtr_ctrl_pkt)
in qrtr_tx_resume(). And skb->len equals to size in qrtr_endpoint_post().
But size is less than sizeof(struct qrtr_ctrl_pkt) when qrtr_cb->type
equals to QRTR_TYPE_RESUME_TX in qrtr_endpoint_post() under the syzbot
scenario. This triggers the uninit variable access bug.

Add size check when qrtr_cb->type equals to QRTR_TYPE_RESUME_TX in
qrtr_endpoint_post() to fix the bug.

Fixes: 5fdeb0d372ab ("net: qrtr: Implement outgoing flow control")
Reported-by: syzbot+4436c9630a45820fda76@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=c14607f0963d27d5a3d5f4c8639b500909e43540
Suggested-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230410012352.3997823-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cgroup,freezer: hold cpu_hotplug_lock before freezer_mutex

[ Upstream commit 57dcd64c7e036299ef526b400a8d12b8a2352f26 ]

syzbot is reporting circular locking dependency between cpu_hotplug_lock
and freezer_mutex, for commit f5d39b020809 ("freezer,sched: Rewrite core
freezer logic") replaced atomic_inc() in freezer_apply_state() with
static_branch_inc() which holds cpu_hotplug_lock.

cpu_hotplug_lock => cgroup_threadgroup_rwsem => freezer_mutex

  cgroup_file_write() {
    cgroup_procs_write() {
      __cgroup_procs_write() {
        cgroup_procs_write_start() {
          cgroup_attach_lock() {
            cpus_read_lock() {
              percpu_down_read(&cpu_hotplug_lock);
            }
            percpu_down_write(&cgroup_threadgroup_rwsem);
          }
        }
        cgroup_attach_task() {
          cgroup_migrate() {
            cgroup_migrate_execute() {
              freezer_attach() {
                mutex_lock(&freezer_mutex);
                (...snipped...)
              }
            }
          }
        }
        (...snipped...)
      }
    }
  }

freezer_mutex => cpu_hotplug_lock

  cgroup_file_write() {
    freezer_write() {
      freezer_change_state() {
        mutex_lock(&freezer_mutex);
        freezer_apply_state() {
          static_branch_inc(&freezer_active) {
            static_key_slow_inc() {
              cpus_read_lock();
              static_key_slow_inc_cpuslocked();
              cpus_read_unlock();
            }
          }
        }
        mutex_unlock(&freezer_mutex);
      }
    }
  }

Swap locking order by moving cpus_read_lock() in freezer_apply_state()
to before mutex_lock(&freezer_mutex) in freezer_change_state().

Reported-by: syzbot <syzbot+c39682e86c9d84152f93@syzkaller.appspotmail.com>
Link: https://syzkaller.appspot.com/bug?extid=c39682e86c9d84152f93
Suggested-by: Hillf Danton <hdanton@sina.com>
Fixes: f5d39b020809 ("freezer,sched: Rewrite core freezer logic")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: wwan: iosm: Fix error handling path in ipc_pcie_probe()

[ Upstream commit a56ef25619e079bd7d744636cf18d054d1e91982 ]

Smatch reports:
drivers/net/wwan/iosm/iosm_ipc_pcie.c:298 ipc_pcie_probe()
warn: missing unwind goto?

When dma_set_mask fails it directly returns without disabling pci
device and freeing ipc_pcie. Fix this my calling a correct goto label

As dma_set_mask returns either 0 or -EIO, we can use a goto label, as
it finally returns -EIO.

Add a set_mask_fail goto label which stands consistent with other goto
labels in this function..

Fixes: 035e3befc191 ("net: wwan: iosm: fix driver not working with INTEL_IOMMU disabled")
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qlcnic: check pci_reset_function result

[ Upstream commit 7573099e10ca69c3be33995c1fcd0d241226816d ]

Static code analyzer complains to unchecked return value.
The result of pci_reset_function() is unchecked.
Despite, the issue is on the FLR supported code path and in that
case reset can be done with pcie_flr(), the patch uses less invasive
approach by adding the result check of pci_reset_function().

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 7e2cf4feba05 ("qlcnic: change driver hardware interface mechanism")
Signed-off-by: Denis Plotnikov <den-plotnikov@yandex-team.ru>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/armada: Fix a potential double free in an error handling path

[ Upstream commit b89ce1177d42d5c124e83f3858818cd4e6a2c46f ]

'priv' is a managed resource, so there is no need to free it explicitly or
there will be a double free().

Fixes: 90ad200b4cbc ("drm/armada: Use devm_drm_dev_alloc")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/c4f3c9207a9fce35cb6dd2cc60e755275961588a.1640536364.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Set ISO Data Path on broadcast sink

[ Upstream commit d2e4f1b1cba8742db66aaf77374cab7c0c7c8656 ]

This patch enables ISO data rx on broadcast sink.

Fixes: eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Claudia Draghicescu <claudia.rosu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: SCO: Fix possible circular locking dependency sco_sock_getsockopt

[ Upstream commit 975abc0c90fc485ff9b4a6afa475c3b1398d5d47 ]

This attempts to fix the following trace:

======================================================
WARNING: possible circular locking dependency detected
6.3.0-rc2-g68fcb3a7bf97 #4706 Not tainted
------------------------------------------------------
sco-tester/31 is trying to acquire lock:
ffff8880025b8070 (&hdev->lock){+.+.}-{3:3}, at:
sco_sock_getsockopt+0x1fc/0xa90

but task is already holding lock:
ffff888001eeb130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}, at:
sco_sock_getsockopt+0x104/0xa90

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #2 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0}:
       lock_sock_nested+0x32/0x80
       sco_connect_cfm+0x118/0x4a0
       hci_sync_conn_complete_evt+0x1e6/0x3d0
       hci_event_packet+0x55c/0x7c0
       hci_rx_work+0x34c/0xa00
       process_one_work+0x575/0x910
       worker_thread+0x89/0x6f0
       kthread+0x14e/0x180
       ret_from_fork+0x2b/0x50

-> #1 (hci_cb_list_lock){+.+.}-{3:3}:
       __mutex_lock+0x13b/0xcc0
       hci_sync_conn_complete_evt+0x1ad/0x3d0
       hci_event_packet+0x55c/0x7c0
       hci_rx_work+0x34c/0xa00
       process_one_work+0x575/0x910
       worker_thread+0x89/0x6f0
       kthread+0x14e/0x180
       ret_from_fork+0x2b/0x50

-> #0 (&hdev->lock){+.+.}-{3:3}:
       __lock_acquire+0x18cc/0x3740
       lock_acquire+0x151/0x3a0
       __mutex_lock+0x13b/0xcc0
       sco_sock_getsockopt+0x1fc/0xa90
       __sys_getsockopt+0xe9/0x190
       __x64_sys_getsockopt+0x5b/0x70
       do_syscall_64+0x42/0x90
       entry_SYSCALL_64_after_hwframe+0x70/0xda

other info that might help us debug this:

Chain exists of:
  &hdev->lock --> hci_cb_list_lock --> sk_lock-AF_BLUETOOTH-BTPROTO_SCO

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
                               lock(hci_cb_list_lock);
                               lock(sk_lock-AF_BLUETOOTH-BTPROTO_SCO);
  lock(&hdev->lock);

 *** DEADLOCK ***

1 lock held by sco-tester/31:
 #0: ffff888001eeb130 (sk_lock-AF_BLUETOOTH-BTPROTO_SCO){+.+.}-{0:0},
 at: sco_sock_getsockopt+0x104/0xa90

Fixes: 248733e87d50 ("Bluetooth: Allow querying of supported offload codecs over SCO socket")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Fix printing errors if LE Connection times out

[ Upstream commit b62e72200eaad523f08d8319bba50fc652e032a8 ]

This fixes errors like bellow when LE Connection times out since that
is actually not a controller error:

 Bluetooth: hci0: Opcode 0x200d failed: -110
 Bluetooth: hci0: request failed to create LE connection: err -110

Instead the code shall properly detect if -ETIMEDOUT is returned and
send HCI_OP_LE_CREATE_CONN_CANCEL to give up on the connection.

Link: https://github.com/bluez/bluez/issues/340
Fixes: 8e8b92ee60de ("Bluetooth: hci_sync: Add hci_le_create_conn_sync")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: hci_conn: Fix not cleaning up on LE Connection failure

[ Upstream commit 19cf60bf63cbaf5262eac400c707966e19999b83 ]

hci_connect_le_scan_cleanup shall always be invoked to cleanup the
states and re-enable passive scanning if necessary, otherwise it may
cause the pending action to stay active causing multiple attempts to
connect.

Fixes: 9b3628d79b46 ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: openvswitch: fix race on port output

[ Upstream commit 066b86787fa3d97b7aefb5ac0a99a22dad2d15f8 ]

assume the following setup on a single machine:
1. An openvswitch instance with one bridge and default flows
2. two network namespaces "server" and "client"
3. two ovs interfaces "server" and "client" on the bridge
4. for each ovs interface a veth pair with a matching name and 32 rx and
   tx queues
5. move the ends of the veth pairs to the respective network namespaces
6. assign ip addresses to each of the veth ends in the namespaces (needs
   to be the same subnet)
7. start some http server on the server network namespace
8. test if a client in the client namespace can reach the http server

when following the actions below the host has a chance of getting a cpu
stuck in a infinite loop:
1. send a large amount of parallel requests to the http server (around
   3000 curls should work)
2. in parallel delete the network namespace (do not delete interfaces or
   stop the server, just kill the namespace)

there is a low chance that this will cause the below kernel cpu stuck
message. If this does not happen just retry.
Below there is also the output of bpftrace for the functions mentioned
in the output.

The series of events happening here is:
1. the network namespace is deleted calling
   `unregister_netdevice_many_notify` somewhere in the process
2. this sets first `NETREG_UNREGISTERING` on both ends of the veth and
   then runs `synchronize_net`
3. it then calls `call_netdevice_notifiers` with `NETDEV_UNREGISTER`
4. this is then handled by `dp_device_event` which calls
   `ovs_netdev_detach_dev` (if a vport is found, which is the case for
   the veth interface attached to ovs)
5. this removes the rx_handlers of the device but does not prevent
   packages to be sent to the device
6. `dp_device_event` then queues the vport deletion to work in
   background as a ovs_lock is needed that we do not hold in the
   unregistration path
7. `unregister_netdevice_many_notify` continues to call
   `netdev_unregister_kobject` which sets `real_num_tx_queues` to 0
8. port deletion continues (but details are not relevant for this issue)
9. at some future point the background task deletes the vport

If after 7. but before 9. a packet is send to the ovs vport (which is
not deleted at this point in time) which forwards it to the
`dev_queue_xmit` flow even though the device is unregistering.
In `skb_tx_hash` (which is called in the `dev_queue_xmit`) path there is
a while loop (if the packet has a rx_queue recorded) that is infinite if
`dev->real_num_tx_queues` is zero.

To prevent this from happening we update `do_output` to handle devices
without carrier the same as if the device is not found (which would
be the code path after 9. is done).

Additionally we now produce a warning in `skb_tx_hash` if we will hit
the infinite loop.

bpftrace (first word is function name):

__dev_queue_xmit server: real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1
netdev_core_pick_tx server: addr: 0xffff9f0a46d4a000 real_num_tx_queues: 1, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 1
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 2, reg_state: 1
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 6, reg_state: 2
ovs_netdev_detach_dev server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, reg_state: 2
netdev_rx_handler_unregister server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
netdev_rx_handler_unregister ret server: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024, reg_state: 2
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 27, reg_state: 2
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 22, reg_state: 2
dp_device_event server: real_num_tx_queues: 1 cpu 9, pid: 21024, tid: 21024, event 18, reg_state: 2
netdev_unregister_kobject: real_num_tx_queues: 1, cpu: 9, pid: 21024, tid: 21024
synchronize_rcu_expedited: cpu 9, pid: 21024, tid: 21024
ovs_vport_send server: real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 2
__dev_queue_xmit server: real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 2
netdev_core_pick_tx server: addr: 0xffff9f0a46d4a000 real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024, skb_addr: 0xffff9edb6f207000, reg_state: 2
broken device server: real_num_tx_queues: 0, cpu: 2, pid: 28024, tid: 28024
ovs_dp_detach_port server: real_num_tx_queues: 0 cpu 9, pid: 9124, tid: 9124, reg_state: 2
synchronize_rcu_expedited: cpu 9, pid: 33604, tid: 33604

stuck message:

watchdog: BUG: soft lockup - CPU#5 stuck for 26s! [curl:1929279]
Modules linked in: veth pktgen bridge stp llc ip_set_hash_net nft_counter xt_set nft_compat nf_tables ip_set_hash_ip ip_set nfnetlink_cttimeout nfnetlink openvswitch nsh nf_conncount nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 tls binfmt_misc nls_iso8859_1 input_leds joydev serio_raw dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua sch_fq_codel drm efi_pstore virtio_rng ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear hid_generic usbhid hid crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel virtio_net ahci net_failover crypto_simd cryptd psmouse libahci virtio_blk failover
CPU: 5 PID: 1929279 Comm: curl Not tainted 5.15.0-67-generic #74-Ubuntu
Hardware name: OpenStack Foundation OpenStack Nova, BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:netdev_pick_tx+0xf1/0x320
Code: 00 00 8d 48 ff 0f b7 c1 66 39 ca 0f 86 e9 01 00 00 45 0f b7 ff 41 39 c7 0f 87 5b 01 00 00 44 29 f8 41 39 c7 0f 87 4f 01 00 00 <eb> f2 0f 1f 44 00 00 49 8b 94 24 28 04 00 00 48 85 d2 0f 84 53 01
RSP: 0018:ffffb78b40298820 EFLAGS: 00000246
RAX: 0000000000000000 RBX: ffff9c8773adc2e0 RCX: 000000000000083f
RDX: 0000000000000000 RSI: ffff9c8773adc2e0 RDI: ffff9c870a25e000
RBP: ffffb78b40298858 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff9c870a25e000
R13: ffff9c870a25e000 R14: ffff9c87fe043480 R15: 0000000000000000
FS:  00007f7b80008f00(0000) GS:ffff9c8e5f740000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f7b80f6a0b0 CR3: 0000000329d66000 CR4: 0000000000350ee0
Call Trace:
 <IRQ>
 netdev_core_pick_tx+0xa4/0xb0
 __dev_queue_xmit+0xf8/0x510
 ? __bpf_prog_exit+0x1e/0x30
 dev_queue_xmit+0x10/0x20
 ovs_vport_send+0xad/0x170 [openvswitch]
 do_output+0x59/0x180 [openvswitch]
 do_execute_actions+0xa80/0xaa0 [openvswitch]
 ? kfree+0x1/0x250
 ? kfree+0x1/0x250
 ? kprobe_perf_func+0x4f/0x2b0
 ? flow_lookup.constprop.0+0x5c/0x110 [openvswitch]
 ovs_execute_actions+0x4c/0x120 [openvswitch]
 ovs_dp_process_packet+0xa1/0x200 [openvswitch]
 ? ovs_ct_update_key.isra.0+0xa8/0x120 [openvswitch]
 ? ovs_ct_fill_key+0x1d/0x30 [openvswitch]
 ? ovs_flow_key_extract+0x2db/0x350 [openvswitch]
 ovs_vport_receive+0x77/0xd0 [openvswitch]
 ? __htab_map_lookup_elem+0x4e/0x60
 ? bpf_prog_680e8aff8547aec1_kfree+0x3b/0x714
 ? trace_call_bpf+0xc8/0x150
 ? kfree+0x1/0x250
 ? kfree+0x1/0x250
 ? kprobe_perf_func+0x4f/0x2b0
 ? kprobe_perf_func+0x4f/0x2b0
 ? __mod_memcg_lruvec_state+0x63/0xe0
 netdev_port_receive+0xc4/0x180 [openvswitch]
 ? netdev_port_receive+0x180/0x180 [openvswitch]
 netdev_frame_hook+0x1f/0x40 [openvswitch]
 __netif_receive_skb_core.constprop.0+0x23d/0xf00
 __netif_receive_skb_one_core+0x3f/0xa0
 __netif_receive_skb+0x15/0x60
 process_backlog+0x9e/0x170
 __napi_poll+0x33/0x180
 net_rx_action+0x126/0x280
 ? ttwu_do_activate+0x72/0xf0
 __do_softirq+0xd9/0x2e7
 ? rcu_report_exp_cpu_mult+0x1b0/0x1b0
 do_softirq+0x7d/0xb0
 </IRQ>
 <TASK>
 __local_bh_enable_ip+0x54/0x60
 ip_finish_output2+0x191/0x460
 __ip_finish_output+0xb7/0x180
 ip_finish_output+0x2e/0xc0
 ip_output+0x78/0x100
 ? __ip_finish_output+0x180/0x180
 ip_local_out+0x5e/0x70
 __ip_queue_xmit+0x184/0x440
 ? tcp_syn_options+0x1f9/0x300
 ip_queue_xmit+0x15/0x20
 __tcp_transmit_skb+0x910/0x9c0
 ? __mod_memcg_state+0x44/0xa0
 tcp_connect+0x437/0x4e0
 ? ktime_get_with_offset+0x60/0xf0
 tcp_v4_connect+0x436/0x530
 __inet_stream_connect+0xd4/0x3a0
 ? kprobe_perf_func+0x4f/0x2b0
 ? aa_sk_perm+0x43/0x1c0
 inet_stream_connect+0x3b/0x60
 __sys_connect_file+0x63/0x70
 __sys_connect+0xa6/0xd0
 ? setfl+0x108/0x170
 ? do_fcntl+0xe8/0x5a0
 __x64_sys_connect+0x18/0x20
 do_syscall_64+0x5c/0xc0
 ? __x64_sys_fcntl+0xa9/0xd0
 ? exit_to_user_mode_prepare+0x37/0xb0
 ? syscall_exit_to_user_mode+0x27/0x50
 ? do_syscall_64+0x69/0xc0
 ? __sys_setsockopt+0xea/0x1e0
 ? exit_to_user_mode_prepare+0x37/0xb0
 ? syscall_exit_to_user_mode+0x27/0x50
 ? __x64_sys_setsockopt+0x1f/0x30
 ? do_syscall_64+0x69/0xc0
 ? irqentry_exit+0x1d/0x30
 ? exc_page_fault+0x89/0x170
 entry_SYSCALL_64_after_hwframe+0x61/0xcb
RIP: 0033:0x7f7b8101c6a7
Code: 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 2a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 18 89 54 24 0c 48 89 34 24 89
RSP: 002b:00007ffffd6b2198 EFLAGS: 00000246 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f7b8101c6a7
RDX: 0000000000000010 RSI: 00007ffffd6b2360 RDI: 0000000000000005
RBP: 0000561f1370d560 R08: 00002795ad21d1ac R09: 0030312e302e302e
R10: 00007ffffd73f080 R11: 0000000000000246 R12: 0000561f1370c410
R13: 0000000000000000 R14: 0000000000000005 R15: 0000000000000000
 </TASK>

Fixes: 7f8a436eaa2c ("openvswitch: Add conntrack action")
Co-developed-by: Luca Czesla <luca.czesla@mail.schwarz>
Signed-off-by: Luca Czesla <luca.czesla@mail.schwarz>
Signed-off-by: Felix Huettner <felix.huettner@mail.schwarz>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/ZC0pBXBAgh7c76CA@kernel-bug-kernel-bug
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: remove active_cvlans and active_svlans bitmaps

[ Upstream commit 9c85b7fa12ef2e4fc11a4e31ac595fb5f9d0ddf9 ]

The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:

    while [ $((i++)) ]
        ip l add l eth0 name eth0.$i type vlan id $i

we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.

On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.

This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
  the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
  removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
  delete the VLAN.

Fixes: 48ccc43ecf10 ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iavf: refactor VLAN filter states

[ Upstream commit 0c0da0e951053fda20412cd284e2714bbbb31bff ]

The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.

Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.

Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: 9c85b7fa12ef ("iavf: remove active_cvlans and active_svlans bitmaps")
Signed-off-by: Sasha Levin <sashal@kernel.org>

bonding: fix ns validation on backup slaves

[ Upstream commit 4598380f9c548aa161eb4e990a1583f0a7d1e0d7 ]

When arp_validate is set to 2, 3, or 6, validation is performed for
backup slaves as well. As stated in the bond documentation, validation
involves checking the broadcast ARP request sent out via the active
slave. This helps determine which slaves are more likely to function in
the event of an active slave failure.

However, when the target is an IPv6 address, the NS message sent from
the active interface is not checked on backup slaves. Additionally,
based on the bond_arp_rcv() rule b, we must reverse the saddr and daddr
when checking the NS message.

Note that when checking the NS message, the destination address is a
multicast address. Therefore, we must convert the target address to
solicited multicast in the bond_get_targets_ip6() function.

Prior to the fix, the backup slaves had a mii status of "down", but
after the fix, all of the slaves' mii status was updated to "UP".

Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tcp: restrict net.ipv4.tcp_app_win

[ Upstream commit dc5110c2d959c1707e12df5f792f41d90614adaa ]

UBSAN: shift-out-of-bounds in net/ipv4/tcp_input.c:555:23
shift exponent 255 is too large for 32-bit type 'int'
CPU: 1 PID: 7907 Comm: ssh Not tainted 6.3.0-rc4-00161-g62bad54b26db-dirty #206
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
 <TASK>
 dump_stack_lvl+0x136/0x150
 __ubsan_handle_shift_out_of_bounds+0x21f/0x5a0
 tcp_init_transfer.cold+0x3a/0xb9
 tcp_finish_connect+0x1d0/0x620
 tcp_rcv_state_process+0xd78/0x4d60
 tcp_v4_do_rcv+0x33d/0x9d0
 __release_sock+0x133/0x3b0
 release_sock+0x58/0x1b0

'maxwin' is int, shifting int for 32 or more bits is undefined behaviour.

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

niu: Fix missing unwind goto in niu_alloc_channels()

[ Upstream commit 8ce07be703456acb00e83d99f3b8036252c33b02 ]

Smatch reports: drivers/net/ethernet/sun/niu.c:4525
niu_alloc_channels() warn: missing unwind goto?

If niu_rbr_fill() fails, then we are directly returning 'err' without
freeing the channels.

Fix this by changing direct return to a goto 'out_err'.

Fixes: a3138df9f20e ("[NIU]: Add Sun Neptune ethernet driver.")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Advertise ID_AA64PFR0_EL1.CSV2/3 to protected VMs

[ Upstream commit e81625218bf7986ba1351a98c43d346b15601d26 ]

The existing pKVM code attempts to advertise CSV2/3 using values
initialized to 0, but never set. To advertise CSV2/3 to protected
guests, pass the CSV2/3 values to hyp when initializing hyp's
view of guests' ID_AA64PFR0_EL1.

Similar to non-protected KVM, these are system-wide, rather than
per cpu, for simplicity.

Fixes: 6c30bfb18d0b ("KVM: arm64: Add handlers for protected VM System Registers")
Signed-off-by: Fuad Tabba <tabba@google.com>
Link: https://lore.kernel.org/r/20230404152321.413064-1-tabba@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: arm64: Initialise hypervisor copies of host symbols unconditionally

[ Upstream commit 6c165223e9a6384aa1e934b90f2650e71adb972a ]

The nVHE object at EL2 maintains its own copies of some host variables
so that, when pKVM is enabled, the host cannot directly modify the
hypervisor state. When running in normal nVHE mode, however, these
variables are still mirrored at EL2 but are not initialised.

Initialise the hypervisor symbols from the host copies regardless of
pKVM, ensuring that any reference to this data at EL2 with normal nVHE
will return a sensibly initialised value.

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Tested-by: Vincent Donnefort <vdonnefort@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20221110190259.26861-16-will@kernel.org
Stable-dep-of: e81625218bf7 ("KVM: arm64: Advertise ID_AA64PFR0_EL1.CSV2/3 to protected VMs")
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf, arm64: Fixed a BTI error on returning to patched function

[ Upstream commit 738a96c4a8c36950803fdd27e7c30aca92dccefd ]

When BPF_TRAMP_F_CALL_ORIG is set, BPF trampoline uses BLR to jump
back to the instruction next to call site to call the patched function.
For BTI-enabled kernel, the instruction next to call site is usually
PACIASP, in this case, it's safe to jump back with BLR. But when
the call site is not followed by a PACIASP or bti, a BTI exception
is triggered.

Here is a fault log:

 Unhandled 64-bit el1h sync exception on CPU0, ESR 0x0000000034000002 -- BTI
 CPU: 0 PID: 263 Comm: test_progs Tainted: GF
 Hardware name: linux,dummy-virt (DT)
 pstate: 40400805 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=-c)
 pc : bpf_fentry_test1+0xc/0x30
 lr : bpf_trampoline_6442573892_0+0x48/0x1000
 sp : ffff80000c0c3a50
 x29: ffff80000c0c3a90 x28: ffff0000c2e6c080 x27: 0000000000000000
 x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000050
 x23: 0000000000000000 x22: 0000ffffcfd2a7f0 x21: 000000000000000a
 x20: 0000ffffcfd2a7f0 x19: 0000000000000000 x18: 0000000000000000
 x17: 0000000000000000 x16: 0000000000000000 x15: 0000ffffcfd2a7f0
 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
 x11: 0000000000000000 x10: ffff80000914f5e4 x9 : ffff8000082a1528
 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0101010101010101
 x5 : 0000000000000000 x4 : 00000000fffffff2 x3 : 0000000000000001
 x2 : ffff8001f4b82000 x1 : 0000000000000000 x0 : 0000000000000001
 Kernel panic - not syncing: Unhandled exception
 CPU: 0 PID: 263 Comm: test_progs Tainted: GF
 Hardware name: linux,dummy-virt (DT)
 Call trace:
  dump_backtrace+0xec/0x144
  show_stack+0x24/0x7c
  dump_stack_lvl+0x8c/0xb8
  dump_stack+0x18/0x34
  panic+0x1cc/0x3ec
  __el0_error_handler_common+0x0/0x130
  el1h_64_sync_handler+0x60/0xd0
  el1h_64_sync+0x78/0x7c
  bpf_fentry_test1+0xc/0x30
  bpf_fentry_test1+0xc/0x30
  bpf_prog_test_run_tracing+0xdc/0x2a0
  __sys_bpf+0x438/0x22a0
  __arm64_sys_bpf+0x30/0x54
  invoke_syscall+0x78/0x110
  el0_svc_common.constprop.0+0x6c/0x1d0
  do_el0_svc+0x38/0xe0
  el0_svc+0x30/0xd0
  el0t_64_sync_handler+0x1ac/0x1b0
  el0t_64_sync+0x1a0/0x1a4
 Kernel Offset: disabled
 CPU features: 0x0000,00034c24,f994fdab
 Memory Limit: none

And the instruction next to call site of bpf_fentry_test1 is ADD,
not PACIASP:

<bpf_fentry_test1>:
bti     c
nop
nop
add     w0, w0, #0x1
paciasp

For BPF prog, JIT always puts a PACIASP after call site for BTI-enabled
kernel, so there is no problem. To fix it, replace BLR with RET to bypass
the branch target check.

Fixes: efc9909fdce0 ("bpf, arm64: Add bpf trampoline for arm64")
Reported-by: Florent Revest <revest@chromium.org>
Signed-off-by: Xu Kuohai <xukuohai@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Florent Revest <revest@chromium.org>
Acked-by: Florent Revest <revest@chromium.org>
Link: https://lore.kernel.org/bpf/20230401234144.3719742-1-xukuohai@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

9p/xen : Fix use after free bug in xen_9pfs_front_remove due to race condition

[ Upstream commit ea4f1009408efb4989a0f139b70fb338e7f687d0 ]

In xen_9pfs_front_probe, it calls xen_9pfs_front_alloc_dataring
to init priv->rings and bound &ring->work with p9_xen_response.

When it calls xen_9pfs_front_event_handler to handle IRQ requests,
it will finally call schedule_work to start the work.

When we call xen_9pfs_front_remove to remove the driver, there
may be a sequence as follows:

Fix it by finishing the work before cleanup in xen_9pfs_front_free.

Note that, this bug is found by static analysis, which might be
false positive.

CPU0                  CPU1

                     |p9_xen_response
xen_9pfs_front_remove|
  xen_9pfs_front_free|
kfree(priv)          |
//free priv          |
                     |p9_tag_lookup
                     |//use priv->client

Fixes: 71ebd71921e4 ("xen/9pfs: connect to the backend")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Eric Van Hensbergen <ericvh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: apple-admac: Fix 'current_tx' not getting freed

[ Upstream commit d9503be5a100c553731c0e8a82c7b4201e8a970c ]

In terminate_all we should queue up all submitted descriptors to be
freed. We do that for the content of the 'issued' and 'submitted' lists,
but the 'current_tx' descriptor falls through the cracks as it's
removed from the 'issued' list once it gets assigned to be the current
descriptor. Explicitly queue up freeing of the 'current_tx' descriptor
to address a memory leak that is otherwise present.

Fixes: b127315d9a78 ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224152222.26732-2-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: apple-admac: Set src_addr_widths capability

[ Upstream commit 6e96adcaa7a29827ac8ee8df290a44957a4823ec ]

Add missing setting of 'src_addr_widths', which is the same as for the
other direction.

Fixes: b127315d9a78 ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224152222.26732-3-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: apple-admac: Handle 'global' interrupt flags

[ Upstream commit a288fd158fbf85c06a9ac01cecabf97ac5d962e7 ]

In addition to TX channel and RX channel interrupt flags there's
another class of 'global' interrupt flags with unknown semantics. Those
weren't being handled up to now, and they are the suspected cause of
stuck IRQ states that have been sporadically occurring. Check the global
flags and clear them if raised.

Fixes: b127315d9a78 ("dmaengine: apple-admac: Add Apple ADMAC driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20230224152222.26732-1-povik+lin@cutebit.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

LoongArch, bpf: Fix jit to skip speculation barrier opcode

[ Upstream commit a6f6a95f25803500079513780d11a911ce551d76 ]

Just skip the opcode(BPF_ST | BPF_NOSPEC) in the BPF JIT instead of
failing to JIT the entire program, given LoongArch currently has no
couterpart of a speculation barrier instruction. To verify the issue,
use the ltp testcase as shown below.

Also, Wang says:

  I can confirm there's currently no speculation barrier equivalent
  on LonogArch. (Loongson says there are builtin mitigations for
  Spectre-V1 and V2 on their chips, and AFAIK efforts to port the
  exploits to mips/LoongArch have all failed a few years ago.)

Without this patch:

  $ ./bpf_prog02
  [...]
  bpf_common.c:123: TBROK: Failed verification: ??? (524)
  [...]
  Summary:
  passed   0
  failed   0
  broken   1
  skipped  0
  warnings 0

With this patch:

  $ ./bpf_prog02
  [...]
  Summary:
  passed   0
  failed   0
  broken   0
  skipped  0
  warnings 0

Fixes: 5dc615520c4d ("LoongArch: Add BPF JIT support")
Signed-off-by: George Guo <guodongtai@kylinos.cn>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: WANG Xuerui <git@xen0n.name>
Cc: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/bpf/20230328071335.2664966-1-guodongtai@kylinos.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>