Dan Carpenter [Thu, 23 Jan 2014 08:21:28 +0000 (11:21 +0300)]
ALSA: bits vs bytes bug in snd_card_create()
commit
4c3773eda49c872a3034382f8ec3080002e715bf upstream.
The test here is intended intended to prevent shift wrapping bugs when
we do "1U << idx2". We should consider the number of bits in a u32
instead of the number of bytes.
[fix another chunk similarly by tiwai]
Fixes:
7bb2491b35a2 ('ALSA: Add kconfig to specify the max card numbers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 10 Jan 2014 13:20:42 +0000 (14:20 +0100)]
ALSA: Enable CONFIG_ZONE_DMA for smaller PCI DMA masks
commit
80ab8eae70e51d578ebbeb228e0f7a562471b8b7 upstream.
The PCI devices with DMA masks smaller than 32bit should enable
CONFIG_ZONE_DMA. Since the recent change of page allocator, page
allocations via dma_alloc_coherent() with the limited DMA mask bits
may fail more frequently, ended up with no available buffers, when
CONFIG_ZONE_DMA isn't enabled. With CONFIG_ZONE_DMA, the system has
much more chance to obtain such pages.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 7 Jan 2014 17:11:44 +0000 (18:11 +0100)]
ALSA: hda - Don't create duplicated ctls for loopback paths
commit
43a8e50a46a4e1dd1451e4a4ffa1f7695fb7d287 upstream.
AD1986A mic pins (0x1d and 0x1f) share the same widget for controlling
the loopback volume/mute, but the generic parser didn't check it.
This ended up with the duplicated controls for the same effect.
This patch adds the check of the duplication for avoiding it.
After this fix, there will be only one control although it affects
both paths; this remaining issue should be fixed later in a different
patch.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Tue, 7 Jan 2014 16:48:11 +0000 (17:48 +0100)]
ALSA: hda - Correct AD1986A 3stack pin configs
commit
ed0e0d0617a8dc3d8b82c6e54827f269f2247b07 upstream.
The 3stack pin configs for AD1986A codec had incorrect values that
resulted in broken mic and line-in.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66621
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Thu, 26 Dec 2013 22:13:08 +0000 (00:13 +0200)]
ALSA: rme9652: fix a missing comma in channel_map_9636_ds[]
commit
770bd4bf2e664939a9dacd3d26ec9ff7a3933210 upstream.
The lack of comma leads to the wrong channel for an SPDIF channel.
Unfortunately this wasn't caught by compiler because it's still a
valid expression.
Reported-by: Alexander Aristov <aristov.alexander@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Charles Keepax [Tue, 21 Jan 2014 16:27:51 +0000 (16:27 +0000)]
ASoC: wm5110: Extend SYSCLK patch file for rev D
commit
34354792432b6e0a3b156819a1a19716c50d3473 upstream.
Latest evaluation of the the device has given some patch file additions
for improved performance.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars-Peter Clausen [Wed, 8 Jan 2014 10:22:25 +0000 (11:22 +0100)]
ASoC: adau1701: Fix ADAU1701_SEROCTL_WORD_LEN_16 constant
commit
e20970ada3f699c113fe64b04492af083d11a7d8 upstream.
The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10,
so 0x2. This patch fixes it.
Reported-by: Magnus Reftel <magnus.reftel@lockless.no>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krzysztof Kozlowski [Fri, 20 Dec 2013 09:35:07 +0000 (10:35 +0100)]
mfd: max77686: Fix regmap resource leak on driver remove
commit
74142ffc0b52cfe6f9d2f6f34a5f3eedbfe3ce51 upstream.
The regmap used by max77686 MFD driver was not freed with regmap_exit()
on driver exit. This lead to leak of resources.
Replace regmap_init_i2c() call in driver probe with initialization of
managed register map so the regmap will be properly freed by the device
management code.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dongsheng Yang [Fri, 20 Dec 2013 18:41:47 +0000 (13:41 -0500)]
perf kvm: Fix kvm report without guestmount.
commit
ad85ace07a05062ef6b59c35a5e80b6eaee1eee6 upstream.
Currently, if we use perf kvm --guestkallsyms --guestmodules report, we
can not get the perf information from perf data file. All sample are
shown as unknown.
Reproducing steps:
# perf kvm --guestkallsyms /tmp/kallsyms --guestmodules /tmp/modules record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.624 MB perf.data.guest (~27260 samples) ]
# perf kvm --guestkallsyms /tmp/kallsyms --guestmodules /tmp/modules report |grep %
100.00% [guest/6471] [unknown] [g] 0xffffffff8164f330
This bug was introduced by
207b57926 (perf kvm: Fix regression with guest machine creation).
In original code, it uses perf_session__find_machine(), it means we deliver symbol to machine
which has the same pid, if no machine found, deliver it to *default* guest. But if we use
perf_session__findnew_machine() here, if no machine was found, new machine with pid will be built
and added. Then the default guest which with pid == 0 will never get a symbol.
And because the new machine initialized here has no kernel map created, the symbol delivered to
it will be marked as "unknown".
This patch here is to revert commit
207b57926 and fix the SEGFAULT bug in another way.
Verification steps:
# ./perf kvm --guestkallsyms /home/kallsyms --guestmodules /home/modules record -a sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.651 MB perf.data.guest (~28437 samples) ]
# ./perf kvm --guestkallsyms /home/kallsyms --guestmodules /home/modules report |grep %
22.64% :6471 [guest.kernel.kallsyms] [g] update_rq_clock.part.70
19.99% :6471 [guest.kernel.kallsyms] [g] d_free
18.46% :6471 [guest.kernel.kallsyms] [g] bio_phys_segments
16.25% :6471 [guest.kernel.kallsyms] [g] dequeue_task
12.78% :6471 [guest.kernel.kallsyms] [g] __switch_to
7.91% :6471 [guest.kernel.kallsyms] [g] scheduler_tick
1.75% :6471 [guest.kernel.kallsyms] [g] native_apic_mem_write
0.21% :6471 [guest.kernel.kallsyms] [g] apic_timer_interrupt
Signed-off-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com>
Acked-by: David Ahern <dsahern@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/r/1387564907-3045-1-git-send-email-yangds.fnst@cn.fujitsu.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen-Yu Tsai [Thu, 16 Jan 2014 06:34:23 +0000 (14:34 +0800)]
pinctrl: sunxi: Honor GPIO output initial vaules
commit
fa8cf57c923e86a693a85aff1df579245a27cbb3 upstream.
Some GPIO users, such as fixed-regulator, request GPIO output with
initial value of 1. This was ignored by sunxi driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Warren [Thu, 23 Jan 2014 23:55:19 +0000 (15:55 -0800)]
rtc: max8907: weekday encoding fixes
commit
75ea799df4cb07e505c91b4abaa87bc28aad3e66 upstream.
The current MAX8907 driver has two issues related to weekday value
handling:
1)
The HW WEEKDAY register has range 0..6 rather than 1..7 as documented.
Note that I validated the actual HW range by observing the HW register
roll from 6->0 rather than 6->7->1 as would otherwise be expected.
This matches Linux's tm_wday range of 0..6.
When the CMOS RAM content is lost, the date returned from the device is
2007-01-01 00:00:00, which is a Monday. The WEEKDAY register reads 1 in
this case. This matches the numbering in Linux's tm_wday field.
Hence we should write Linux's tm_wday value to the register without
modifying it. Hence, remove the +1/-1 calculations for WEEKDAY/tm_wday.
2)
There's no need to make alarms match on the WEEKDAY register, since the
other fields together uniquely define the alarm date/time. Ignoring the
WEEKDAY value in the match isolates the driver from any incorrect value in
the current time copy of the WEEKDAY register.
Each change individually, or both together, solves an issue that I
observed; "hwclock -r" would time out waiting for its alarm to fire if the
CMOS RAM content had been lost, and hence the WEEKDAY register value
mismatched what the driver expected it to be. "hwclock -w" would solve
this by over-writing the HW default WEEKDAY register value with what the
driver expected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sebastian Andrzej Siewior [Wed, 27 Nov 2013 16:43:43 +0000 (17:43 +0100)]
parport: parport_pc: remove double PCI ID for NetMos
commit
d6a484520c5572a4170fa915109ccfc0c38f5008 upstream.
In commit 85747f ("PATCH] parport: add NetMOS 9805 support") Max added
the PCI ID for NetMOS 9805 based on a Debian bug report from 2k4 which
was at the v2.4.26 time frame. The patch made into 2.6.14.
Shortly before that patch akpm merged commit
296d3c783b ("[PATCH] Support
NetMOS based PCI cards providing serial and parallel ports") which made
into v2.6.9-rc1.
Now we have two different entries for the same PCI id.
I have here the NetMos 9805 which claims to support SPP/EPP/ECP mode.
This patch takes Max's entry for titan_1284p1 (base != -1 specifies the
ioport for ECP mode) and replaces akpm's entry for netmos_9805 which
specified -1 (=none). Both share the same PCI-ID (my card has subsystem
0x1000 / 0x0020 so it should match PCI_ANY).
While here I also drop the entry for titan_1284p2 which is the same as
netmos_9815.
Cc: Maximilian Attems <maks@stro.at>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Tue, 21 Jan 2014 16:31:10 +0000 (17:31 +0100)]
s390/uapi: fix struct statfs64 definition
commit
4e078146dff728f4865270a47710d57797e81eb6 upstream.
With
b8668fd0a7e1b59f "s390/uapi: change struct statfs[64] member types
to unsigned values" the size of a couple of struct statfs64 member got
incorrectly changed from 64 to 32 bit for 32 bit builds.
Fix this by changing the type of couple of struct statfs64 members from
unsigned long to unsigned long long.
The definition of struct compat_statfs64 was correct however.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dominik Dingel [Mon, 9 Dec 2013 17:30:01 +0000 (18:30 +0100)]
KVM: s390: ioeventfd: ignore leftmost bits
commit
ff1f3cb4b3ac5d039f02679f34cb1498d110d241 upstream.
The diagnose 500 subcode 3 contains the 32 bit subchannel id in bits 32-63
(counting from the left). As for other I/O instructions, bits 0-31 should be
ignored and thus not be passed to kvm_io_bus_write_cookie().
This fixes a bug where the guest passed non-zero bits 0-31 which the
host tried to interpret, leading to ioeventfd notification failures.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Mon, 11 Nov 2013 12:56:47 +0000 (13:56 +0100)]
KVM: s390: fix diagnose code extraction
commit
743db27c526e0f31cc507959d662e97e2048a86f upstream.
The diagnose code to be used is the contents of the base register (if not
zero), plus the displacement. The current code ignores the base register
contents. So let's fix that...
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Warren [Tue, 7 Jan 2014 22:00:12 +0000 (15:00 -0700)]
serial: 8250: enable UART_BUG_NOMSR for Tegra
commit
3685f19e07802ec4207b52465c408f185b66490e upstream.
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Woithe [Mon, 9 Dec 2013 06:03:08 +0000 (16:33 +1030)]
serial: 8250: Fix initialisation of Quatech cards with the AMCC PCI chip
commit
9c5320f8d7d9a2cf623e65d50e1113f34d9b9eb1 upstream.
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yegor Yefremov [Mon, 9 Dec 2013 11:11:15 +0000 (12:11 +0100)]
serial: add support for 200 v3 series Titan card
commit
48c0247d7b7bf58abb85a39021099529df365c4d upstream.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Mon, 6 Jan 2014 21:07:03 +0000 (13:07 -0800)]
xhci: Set scatter-gather limit to avoid failed block writes.
commit
f2d9b991c549f159dc9ae81f77d8206c790cbfee upstream.
Commit
35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb: xhci: Link TRB
must not occur within a USB payload burst" attempted to fix an issue
found with USB ethernet adapters, and inadvertently broke USB storage
devices. The patch attempts to ensure that transfers never span a
segment, and rejects transfers that have more than 63 entries (or
possibly less, if some entries cross 64KB boundaries).
usb-storage limits the maximum transfer size to 120K, and we had assumed
the block layer would pass a scatter-gather list of 4K entries,
resulting in no more than 31 sglist entries:
http://marc.info/?l=linux-usb&m=
138498190419312&w=2
That assumption was wrong, since we've seen the driver reject a write
that was 218 sectors long (of probably 512 bytes each):
Jan 1 07:04:49 jidanni5 kernel: [ 559.624704] xhci_hcd 0000:00:14.0: Too many fragments 79, max 63
...
Jan 1 07:04:58 jidanni5 kernel: [ 568.622583] Write(10): 2a 00 00 06 85 0e 00 00 da 00
Limit the number of scatter-gather entries to half a ring segment. That
should be margin enough in case some entries cross 64KB boundaries.
Increase the number of TRBs per segment from 64 to 256, which should
result in ring segments fitting on a 4K page.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes:
35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst')
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Mon, 6 Jan 2014 03:16:32 +0000 (03:16 +0000)]
xhci: Avoid infinite loop when sg urb requires too many trbs
commit
d6c9ea9069af684358efedcaf2f2f687f51c58ee upstream.
Currently prepare_ring() returns -ENOMEM if the urb won't fit into a
single ring segment. usb_sg_wait() treats this error as a temporary
condition and will keep retrying until something else goes wrong.
The number of retries should be limited in usb_sg_wait(), but also
prepare_ring() should not return an error code that suggests it might
be worth retrying. Change it to -EINVAL.
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes:
35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst')
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Phil Pokorny [Tue, 14 Jan 2014 18:46:46 +0000 (10:46 -0800)]
hwmon: (k10temp) Add support for Kaveri CPUs
commit
d303b1b5fbb688282bbf72a534b9dfed7af9fe4f upstream.
Add new PCI ID to support new model "Kaveri" family.
Signed-off-by: Philip Pokorny <ppokorny@penguincomputing.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean-Jacques Hiblot [Thu, 9 Jan 2014 15:01:54 +0000 (16:01 +0100)]
ARM: at91: smc: bug fix in sam9_smc_cs_read()
commit
1588c51cf6d782e63a8719681d905ef0ac22ee62 upstream.
There was a copy/paste error when reading the nwe_pulse value.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ludovic Desroches [Fri, 22 Nov 2013 13:49:52 +0000 (14:49 +0100)]
ARM: at91: at91sam9g45: set default mmc pinctrl-names
commit
0645b93f6c223b594c0dca348e2ae0a23bccf6e3 upstream.
pinctrl-names property was missing from mmc nodes.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Roszko [Fri, 10 Jan 2014 09:33:11 +0000 (10:33 +0100)]
tty/serial: at91: disable uart timer at start of shutdown
commit
8bc661bfc0c2d221e209f4205bdaaf574d50100c upstream.
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Deneen [Tue, 7 Jan 2014 10:45:09 +0000 (11:45 +0100)]
tty/serial: at91: reset rx_ring when port is shutdown
commit
bb7e73c598fb226c75f7625088a8f6a45a0fc892 upstream.
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Roszko [Tue, 7 Jan 2014 10:45:07 +0000 (11:45 +0100)]
tty/serial: at91: fix race condition in atmel_serial_remove
commit
f50c995f9ebf064cea1368bf361c4e29679415b4 upstream.
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Roszko [Tue, 7 Jan 2014 10:45:06 +0000 (11:45 +0100)]
tty/serial: at91: Handle shutdown more safely
commit
0cc7c6c7916b1b6f34350ff1473b80b9f7e459c0 upstream.
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<
c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<
c001fd34>] (tasklet_action+0x70/0xa8)
[<
c001fd34>] (tasklet_action+0x70/0xa8) from [<
c001f60c>] (__do_softirq+0x90/0x144)
[<
c001f60c>] (__do_softirq+0x90/0x144) from [<
c001fa18>] (irq_exit+0x40/0x4c)
[<
c001fa18>] (irq_exit+0x40/0x4c) from [<
c000e298>] (handle_IRQ+0x64/0x84)
[<
c000e298>] (handle_IRQ+0x64/0x84) from [<
c000d6c0>] (__irq_svc+0x40/0x50)
[<
c000d6c0>] (__irq_svc+0x40/0x50) from [<
c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<
c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<
c0209740>] (atmel_shutdown+0x104/0x160)
[<
c0209740>] (atmel_shutdown+0x104/0x160) from [<
c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler [Wed, 8 Jan 2014 18:19:22 +0000 (20:19 +0200)]
mei: use hbm idle state to prevent spurious resets
commit
66ae460b13c31a176b41550259683c841a62af3e upstream.
When reset is caused by hbm protocol mismatch or timeout
we might end up in an endless reset loop and hbm protocol
will never sync
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Wed, 1 Jan 2014 19:19:28 +0000 (19:19 +0000)]
staging: vt6656: CARDqGetNextTBTT correct uLowNextTBTT
commit
9acec059c0cef0bf086c738f4c0b1f4447782a48 upstream.
value uLowNextTBTT yields wrong value.
ULL is needed with qwTSF
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Malcolm Priestley [Sun, 8 Dec 2013 09:11:30 +0000 (09:11 +0000)]
staging: vt6656: [BUG] BBvUpdatePreEDThreshold Always set sensitivity on bScanning
commit
8f248dae133668bfb8e9379b4b3f0571c858b24a upstream.
byBBPreEDIndex value is initially 0, this means that from
cold BBvUpdatePreEDThreshold is never set.
This means that sensitivity may be in an ambiguous state,
failing to scan any wireless points or at least distant ones.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Tue, 24 Dec 2013 17:22:54 +0000 (11:22 -0600)]
staging: r8712u: Set device type to wlan
commit
3a21f00a5002b14e4aab52aef59d33ed28468a13 upstream.
The latest version of NetworkManager does not recognize the device as wireless
without this change.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amir Shehata [Tue, 3 Dec 2013 13:58:47 +0000 (21:58 +0800)]
staging/lustre/ptlrpc: Fix a crash when dereferencing NULL pointer
commit
3c92a0bf4d72737035a16c4fe357ccd439c9b7d2 upstream.
When a system runs out of memory and the function
ptlrpc_register_bulk() is called from ptl_send_rpc() the call to
LNetMEAttach() fails due to failure to allocate memory. This forces
the code into an error path, which most probably previously went
untested. The error path:
if (rc != 0) {
CERROR("%s: LNetMEAttach failed x"LPU64"/%d: rc = %dn",
desc->bd_export->exp_obd->obd_name, xid,
posted_md, rc);
break;
}
This print assumes that desc->bd_export is not NULL. However, it is.
In fact it is expected to be NULL. desc->bd_import is the correct
structure to access in this case.
Lustre-change: http://review.whamcloud.com/7121
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3585
Signed-off-by: Amir Shehata <amir.shehata@intel.com>
Reviewed-by: Liang Zhen <liang.zhen@intel.com>
Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sujith Manoharan [Thu, 9 Jan 2014 03:21:15 +0000 (08:51 +0530)]
ath9k: Disable cross-band FCC
commit
1e2f9295f4c657500111514f92a3d3894d0e05b4 upstream.
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sujith Manoharan [Thu, 9 Jan 2014 03:21:14 +0000 (08:51 +0530)]
ath9k: Use correct channel for RX packets
commit
ff9a93f2ebb88ac7aab9568de80b64b92078e96d upstream.
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ZHAO Gang [Fri, 17 Jan 2014 16:17:38 +0000 (00:17 +0800)]
b43: fix the wrong assignment of status.freq in b43_rx()
commit
64e5acb09ca6b50c97299cff9ef51299470b29f2 upstream.
Use the right function to update frequency value.
If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.
Fixes:
8318d78a44d4 ("cfg80211 API for channels/bitrates, mac80211 and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Sun, 12 Jan 2014 21:11:39 +0000 (15:11 -0600)]
b43legacy: Fix unload oops if firmware is not available
commit
452028665312672c6ba9e16a19248ee00ead9400 upstream.
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Sun, 12 Jan 2014 21:11:38 +0000 (15:11 -0600)]
b43: Fix unload oops if firmware is not available
commit
0673effd41dba323d6a280ef37b5ef29f3f5a653 upstream.
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Sun, 12 Jan 2014 21:11:37 +0000 (15:11 -0600)]
b43: Fix lockdep splat
commit
09164043f63c947a49797750a09ca1cd7c31108e upstream.
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<
ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<
ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eliad Peller [Sun, 5 Jan 2014 10:41:12 +0000 (12:41 +0200)]
iwlwifi: mvm: fix missing cleanup in .start() error path
commit
91b0d1198417cf4fd9a7bd4138b6909f0b359099 upstream.
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emmanuel Grumbach [Tue, 24 Dec 2013 12:15:41 +0000 (14:15 +0200)]
iwlwifi: pcie: enable oscillator for L1 exit
commit
2d93aee152b1758a94a18fe15d72153ba73b5679 upstream.
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Fixes:
99cd47142399 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bing Zhao [Wed, 15 Jan 2014 03:16:34 +0000 (19:16 -0800)]
mwifiex: fix wrong 11ac bits setting in fw_cap_info
commit
1e202242ee1432d68a8bea4919b2ae0ef19d9e06 upstream.
bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amitkumar Karwar [Fri, 10 Jan 2014 22:30:41 +0000 (14:30 -0800)]
mwifiex: add missing endian conversion for fw_tsf
commit
9795229752c31da0c5f8a7dc4c827665327b52f9 upstream.
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 25 Nov 2013 16:45:28 +0000 (10:45 -0600)]
rtlwifi: rtl8188ee: Fix typo in code
commit
f699273d6a624266ebc9198774f06ee64a3847a1 upstream.
The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:35 +0000 (11:11 -0600)]
rtlwifi: Add missing code to PWDB statics routine
commit
d82403a9f407217b6aed5260aa92a120e8e98310 upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:34 +0000 (11:11 -0600)]
rtlwifi: rtl8192cu: Fix some code in RF handling
commit
e9b0784bb9de3152e787ee779868c626b137fb3b upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:33 +0000 (11:11 -0600)]
rtlwifi: rtl8192cu: Update the power index registers
commit
9806eacf5de27ab01d680c5d75c92a3a89734e4f upstream.
This patch uses the newly introduced power index register routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:32 +0000 (11:11 -0600)]
rtlwifi: rtl8192c: Add routines to save/restore power index registers
commit
97204e93f01868eeba6ae5c4f3270f32905bb418 upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:30 +0000 (11:11 -0600)]
rtlwifi: Increase the RX queue length for USB drivers
commit
dc6405712268fe514d3dd89aa936c4397b0871b9 upstream.
The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:29 +0000 (11:11 -0600)]
rtlwifi: rtl8192c: Add new definitions in the dm_common header
commit
c908c74e005de780fddbe8cb6fcd44803f5d4b74 upstream.
Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:28 +0000 (11:11 -0600)]
rtlwifi: Set the link state
commit
619ce76f8bb850b57032501a39f26aa6c6731c70 upstream.
The present code fails to set the linked state when an interface is
added.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:27 +0000 (11:11 -0600)]
rtlwifi: Redo register save locations
commit
b9a758a8c905fc59e783ae91ad645452d877ea88 upstream.
The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:26 +0000 (11:11 -0600)]
rtlwifi: rtl8192cu: Add new firmware
commit
62009b7f12793c932aaba0df946b04cb4a77d022 upstream.
Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.
20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:25 +0000 (11:11 -0600)]
rtlwifi: rtl8192c: Prevent reconnect attempts if not connected
commit
8fd77aec1a9d6f4328fc0244f21932114e066df3 upstream.
This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Mon, 18 Nov 2013 17:11:31 +0000 (11:11 -0600)]
rtlwifi: Update beacon statistics for USB driver
commit
65b9cc97c6852fae19dc5c7745e9abc8dd380aad upstream.
The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Thu, 9 Jan 2014 16:27:27 +0000 (10:27 -0600)]
rtlwifi: rtl8192cu: Add new device ID
commit
f87f960b2fb802f26ee3b00c19320e57a9c583ff upstream.
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:26 +0000 (13:51 +0800)]
usb: ehci: add freescale imx28 special write register method
commit
feffe09f510c475df082546815f9e4a573f6a233 upstream.
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=
137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 7 Jan 2014 15:43:02 +0000 (10:43 -0500)]
USB: fix race between hub_disconnect and recursively_mark_NOTATTACHED
commit
543d7784b07ffd16cc82a9cb4e1e0323fd0040f1 upstream.
There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED(). This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed. When the race occurs, it can cause an oops:
BUG: unable to handle kernel NULL pointer dereference at
0000015c
IP: [<
c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<
c16d6082>] usb_set_device_state+0x92/0x120
[<
c16d862b>] usb_disconnect+0x2b/0x1a0
[<
c16dd4c0>] usb_remove_hcd+0xb0/0x160
[<
c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<
c1704efc>] ehci_mid_remove+0x1c/0x30
[<
c1704f26>] ehci_mid_stop_host+0x16/0x30
[<
c16f7698>] penwell_otg_work+0xd28/0x3520
[<
c19c945b>] ? __schedule+0x39b/0x7f0
[<
c19cdb9d>] ? sub_preempt_count+0x3d/0x50
[<
c125e97d>] process_one_work+0x11d/0x3d0
[<
c19c7f4d>] ? mutex_unlock+0xd/0x10
[<
c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
[<
c125f009>] worker_thread+0xf9/0x320
[<
c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<
c125ef10>] ? rescuer_thread+0x2b0/0x2b0
[<
c1264ac4>] kthread+0x94/0xa0
[<
c19d0f77>] ret_from_kernel_thread+0x1b/0x28
[<
c1264a30>] ? kthread_create_on_node+0xc0/0xc0
One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.
To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values. (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.) We also need to
remove the port devices after maxchild has been set to 0, instead of
before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jack Pham [Fri, 15 Nov 2013 22:53:14 +0000 (14:53 -0800)]
usb: xhci: Check for XHCI_PLAT in xhci_cleanup_msix()
commit
9005355af23856c55a5538c9024355785424821b upstream.
If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.
This patch should be backported to kernels as old as 3.9, that
contain the commit
52fb61250a7a132b0cfb9f4a1060a1f3c49e5a25
"xhci-plat: Don't enable legacy PCI interrupts."
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikhail Zolotaryov [Fri, 27 Dec 2013 23:56:35 +0000 (01:56 +0200)]
USB: Nokia 502 is an unusual device
commit
0e16114f2db4838251fb64f3b550996ad3585890 upstream.
The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170
The workaround is (MAX_SECTORS_64):
rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m
The patch adds the tested device to the unusual list permanently.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Colin Leitner [Mon, 6 Jan 2014 20:33:54 +0000 (21:33 +0100)]
USB: ftdi_sio: added CS5 quirk for broken smartcard readers
commit
c1f15196ac3b541d084dc80a8fbd8a74c6a0bd44 upstream.
Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Thu, 2 Jan 2014 21:49:24 +0000 (22:49 +0100)]
USB: cypress_m8: fix ring-indicator detection and reporting
commit
440ebadeae9298d7de3d4d105342691841ec88d0 upstream.
Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.
This bug predates git.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rahul Bedarkar [Thu, 2 Jan 2014 15:27:56 +0000 (20:57 +0530)]
USB: serial: add support for iBall 3.5G connect usb modem
commit
7d5c1b9c7cb5ec8e52b1adc65c484a923a8ea6c3 upstream.
Add support for iBall 3.5G connect usb modem.
$lsusb
Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY
$usb-devices
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9605 Rev=00.00
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=
1234567890ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
张君 [Wed, 18 Dec 2013 07:37:17 +0000 (15:37 +0800)]
usb: option: add new zte 3g modem pids to option driver
commit
4d90b819ae4c7ea8fd5e2bb7edc68c0f334be2e4 upstream.
Signed-off-by: Jun zhang <zhang.jun92@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan Hovold [Sun, 29 Dec 2013 18:22:53 +0000 (19:22 +0100)]
USB: pl2303: fix data corruption on termios updates
commit
623c8263376c0b8a4b0c220232e7313d762cd0cc upstream.
Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.
The common case was fixed by commit
bf5e5834bffc6 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:32 +0000 (13:51 +0800)]
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
commit
2fc5a7dace3c43e62402ab4e8800a8f1834ffe2a upstream.
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:31 +0000 (13:51 +0800)]
usb: chipidea: need to mask INT_STATUS when write otgsc
commit
5332ff1fb63c46588656e4208201bc131627c878 upstream.
For otgsc, both enable bits and status bits are in it. So we need
to make sure the status bits are not be cleared when write enable
bits. It can fix one bug that we plug in/out Micro AB cable fast,
and sometimes, the IDIS will be cleared wrongly when handle last
ID interrupt (ID 0->1), so the current interrupt will not occur.
For stable tree: 3.12+
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:28 +0000 (13:51 +0800)]
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
commit
1071055e2a118a81c0b300d7f4af7eba3f7a7c82 upstream.
Due to imx28 needs ARM swp instruction for writing, we set
CI_HDRC_IMX28_WRITE_FIX for imx28.
This patch is needed for stable tree 3.11+
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Fri, 10 Jan 2014 05:51:27 +0000 (13:51 +0800)]
usb: chipidea: add freescale imx28 special write register method
commit
ed8f8318d2ef3e5f9e4ddf79349508c116b68d7f upstream.
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement special hw_write
and hw_test_and_clear for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=
137996395529294&w=2
This patch is needed for stable tree 3.11+.
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Mon, 27 Jan 2014 13:51:44 +0000 (14:51 +0100)]
x86, kvm: correctly access the KVM_CPUID_FEATURES leaf at 0x40000101
commit
77f01bdfa5e55dc19d3eb747181d2730a9bb3ca8 upstream.
When Hyper-V hypervisor leaves are present, KVM must relocate
its own leaves at 0x40000100, because Windows does not look for
Hyper-V leaves at indices other than 0x40000000. In this case,
the KVM features are at 0x40000101, but the old code would always
look at 0x40000001.
Fix by using kvm_cpuid_base(). This also requires making the
function non-inline, since kvm_cpuid_base() is static.
Fixes:
1085ba7f552d84aa8ac0ae903fa8d0cc2ff9f79d
Cc: mtosatti@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Bonzini [Mon, 27 Jan 2014 13:49:40 +0000 (14:49 +0100)]
x86, kvm: cache the base of the KVM cpuid leaves
commit
1c300a40772dae829b91dad634999a6a522c0829 upstream.
It is unnecessary to go through hypervisor_cpuid_base every time
a leaf is found (which will be every time a feature is requested
after the next patch).
Fixes:
1085ba7f552d84aa8ac0ae903fa8d0cc2ff9f79d
Cc: mtosatti@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcelo Tosatti [Mon, 6 Jan 2014 14:00:02 +0000 (12:00 -0200)]
KVM: x86: limit PIT timer frequency
commit
9ed96e87c5748de4c2807ef17e81287c7304186c upstream.
Limit PIT timer frequency similarly to the limit applied by
LAPIC timer.
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Young [Fri, 20 Dec 2013 10:02:15 +0000 (18:02 +0800)]
x86/efi: Fix off-by-one bug in EFI Boot Services reservation
commit
a7f84f03f660d93574ac88835d056c0d6468aebe upstream.
Current code check boot service region with kernel text region by:
start+size >= __pa_symbol(_text)
The end of the above region should be start + size - 1 instead.
I see this problem in ovmf + Fedora 19 grub boot:
text start: 1000000 md start: 800000 md size: 800000
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PaX Team [Fri, 31 Jan 2014 00:59:25 +0000 (16:59 -0800)]
x86, x32: Correct invalid use of user timespec in the kernel
commit
2def2ef2ae5f3990aabdbe8a755911902707d268 upstream.
The x32 case for the recvmsg() timout handling is broken:
asmlinkage long compat_sys_recvmmsg(int fd, struct compat_mmsghdr __user *mmsg,
unsigned int vlen, unsigned int flags,
struct compat_timespec __user *timeout)
{
int datagrams;
struct timespec ktspec;
if (flags & MSG_CMSG_COMPAT)
return -EINVAL;
if (COMPAT_USE_64BIT_TIME)
return __sys_recvmmsg(fd, (struct mmsghdr __user *)mmsg, vlen,
flags | MSG_CMSG_COMPAT,
(struct timespec *) timeout);
...
The timeout pointer parameter is provided by userland (hence the __user
annotation) but for x32 syscalls it's simply cast to a kernel pointer
and is passed to __sys_recvmmsg which will eventually directly
dereference it for both reading and writing. Other callers to
__sys_recvmmsg properly copy from userland to the kernel first.
The bug was introduced by commit
ee4fa23c4bfc ("compat: Use
COMPAT_USE_64BIT_TIME in net/compat.c") and should affect all kernels
since 3.4 (and perhaps vendor kernels if they backported x32 support
along with this code).
Note that CONFIG_X86_X32_ABI gets enabled at build time and only if
CONFIG_X86_X32 is enabled and ld can build x32 executables.
Other uses of COMPAT_USE_64BIT_TIME seem fine.
This addresses CVE-2014-0038.
Signed-off-by: PaX Team <pageexec@freemail.hu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Rientjes [Thu, 30 Jan 2014 23:46:08 +0000 (15:46 -0800)]
mm/mempolicy.c: fix mempolicy printing in numa_maps
commit
8790c71a18e5d2d93532ae250bcf5eddbba729cd upstream.
As a result of commit
5606e3877ad8 ("mm: numa: Migrate on reference
policy"), /proc/<pid>/numa_maps prints the mempolicy for any <pid> as
"prefer:N" for the local node, N, of the process reading the file.
This should only be printed when the mempolicy of <pid> is
MPOL_PREFERRED for node N.
If the process is actually only using the default mempolicy for local
node allocation, make sure "default" is printed as expected.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Robert Lippert <rlippert@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Ertman [Sat, 14 Dec 2013 07:18:18 +0000 (07:18 +0000)]
e1000e: fix compiler warnings
commit
9e6c3b63399dd424d33a34e08b77f2cab0b84cdc upstream.
This patch is to fix a compiler warning of __bad_udelay due to a value
of >999 being passed as a parameter to udelay() in the function
e1000e_phy_has_link_generic(). This affects the gcc compiler when
it is given a flag of -O3 and the icc compiler.
This patch is also making the change from mdelay() to msleep() in the
same function, since it was determined though code inspection that this
function is never called in atomic context.
Signed-off-by: David Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aristeu Rozanski [Thu, 5 Dec 2013 15:37:56 +0000 (10:37 -0500)]
e752x_edac: Fix pci_dev usage count
commit
90ed4988b8c030d65b41b7d13140e9376dc6ec5a upstream.
In case the device 0, function 1 is not found using pci_get_device(),
pci_scan_single_device() will be used but, differently than
pci_get_device(), it allocates a pci_dev but doesn't does bump the usage
count on the pci_dev and after few module removals and loads the pci_dev
will be freed.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Reviewed-by: mark gross <mark.gross@intel.com>
Link: http://lkml.kernel.org/r/20131205153755.GL4545@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Arcangeli [Thu, 21 Nov 2013 22:32:02 +0000 (14:32 -0800)]
mm: hugetlbfs: fix hugetlbfs optimization
commit
27c73ae759774e63313c1fbfeb17ba076cea64c5 upstream.
Commit
7cb2ef56e6a8 ("mm: fix aio performance regression for database
caused by THP") can cause dereference of a dangling pointer if
split_huge_page runs during PageHuge() if there are updates to the
tail_page->private field.
Also it is repeating compound_head twice for hugetlbfs and it is running
compound_head+compound_trans_head for THP when a single one is needed in
both cases.
The new code within the PageSlab() check doesn't need to verify that the
THP page size is never bigger than the smallest hugetlbfs page size, to
avoid memory corruption.
A longstanding theoretical race condition was found while fixing the
above (see the change right after the skip_unlock label, that is
relevant for the compound_lock path too).
By re-establishing the _mapcount tail refcounting for all compound
pages, this also fixes the below problem:
echo 0 >/sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
BUG: Bad page state in process bash pfn:59a01
page:
ffffea000139b038 count:0 mapcount:10 mapping: (null) index:0x0
page flags: 0x1c00000000008000(tail)
Modules linked in:
CPU: 6 PID: 2018 Comm: bash Not tainted 3.12.0+ #25
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x55/0x76
bad_page+0xd5/0x130
free_pages_prepare+0x213/0x280
__free_pages+0x36/0x80
update_and_free_page+0xc1/0xd0
free_pool_huge_page+0xc2/0xe0
set_max_huge_pages.part.58+0x14c/0x220
nr_hugepages_store_common.isra.60+0xd0/0xf0
nr_hugepages_store+0x13/0x20
kobj_attr_store+0xf/0x20
sysfs_write_file+0x189/0x1e0
vfs_write+0xc5/0x1f0
SyS_write+0x55/0xb0
system_call_fastpath+0x16/0x1b
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ilia Mirkin [Tue, 7 Jan 2014 17:33:59 +0000 (12:33 -0500)]
drm/nouveau/bios: fix offset calculation for BMPv1 bioses
commit
5d2f4767c4eacab351b8450b0de4d3261fe1a957 upstream.
The only BIOS on record that needs the 14 offset has a bios major
version 2 but BMP version 1.01. Another bunch of BIOSes that need the 18
offset have BMP version 2.01 or 5.01 or higher. So instead of looking at the
bios major version, look at the BMP version. BIOSes with BMP version 0
do not contain a detectable script, so always return 0 for them.
See https://bugs.freedesktop.org/show_bug.cgi?id=68835
Reported-by: Mauro Molinari <mauromol@tiscali.it>
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Wed, 15 Jan 2014 22:35:38 +0000 (09:35 +1100)]
md/raid5: fix long-standing problem with bitmap handling on write failure.
commit
9f97e4b128d2ea90a5f5063ea0ee3b0911f4c669 upstream.
Before a write starts we set a bit in the write-intent bitmap.
When the write completes we clear that bit if the write was successful
to all devices. However if the write wasn't fully successful we
should not clear the bit. If the faulty drive is subsequently
re-added, the fact that the bit is still set ensure that we will
re-write the data that is missing.
This logic is mediated by the STRIPE_DEGRADED flag - we only clear the
bitmap bit when this flag is not set.
Currently we correctly set the flag if a write starts when some
devices are failed or missing. But we do *not* set the flag if some
device failed during the write attempt.
This is wrong and can result in clearing the bit inappropriately.
So: set the flag when a write fails.
This bug has been present since bitmaps were introduces, so the fix is
suitable for any -stable kernel.
Reported-by: Ethan Wilson <ethan.wilson@shiftmail.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Jones [Wed, 15 Jan 2014 12:39:59 +0000 (13:39 +0100)]
kvm: x86: fix apic_base enable check
commit
0dce7cd67fd9055c4a2ff278f8af1431e646d346 upstream.
Commit
e66d2ae7c67bd moved the assignment
vcpu->arch.apic_base = value above a condition with
(vcpu->arch.apic_base ^ value), causing that check
to always fail. Use old_value, vcpu->arch.apic_base's
old value, in the condition instead.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Sat, 25 Jan 2014 17:18:00 +0000 (09:18 -0800)]
Linux 3.12.9
Taras Kondratiuk [Fri, 10 Jan 2014 00:27:08 +0000 (01:27 +0100)]
ARM: 7938/1: OMAP4/highbank: Flush L2 cache before disabling
commit
b25f3e1c358434bf850220e04f28eebfc45eb634 upstream.
Kexec disables outer cache before jumping to reboot code, but it doesn't
flush it explicitly. Flush is done implicitly inside of l2x0_disable().
But some SoC's override default .disable handler and don't flush cache.
This may lead to a corrupted memory during Kexec reboot on these
platforms.
This patch adds cache flush inside of OMAP4 and Highbank outer_cache.disable()
handlers to make it consistent with default l2x0_disable().
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Tue, 7 Jan 2014 14:15:36 +0000 (16:15 +0200)]
drm/i915: Don't grab crtc mutexes in intel_modeset_gem_init()
commit
7ad228b11ec26a820291c9f5a1168d6176580dc1 upstream.
When the pipe A force quirk is applied the code will attempt to grab
a crtc mutex during intel_modeset_setup_hw_state(). If we're already
holding all crtc mutexes this will obviously deadlock every time.
So instead of using drm_modeset_lock_all() just grab the
mode_config.mutex. This is enough to avoid the unlocked mutex warnings
from certain lower level functions.
The regression was introduced in:
commit
027476642811f8559cbe00ef6cc54db230e48a20
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Dec 2 11:08:06 2013 +0200
drm/i915: Take modeset locks around intel_modeset_setup_hw_state()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Add cc: stable since the offending commit has that, too.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sudeep Holla [Wed, 8 Jan 2014 17:24:21 +0000 (18:24 +0100)]
ARM: 7934/1: DT/kernel: fix arch_match_cpu_phys_id to avoid erroneous match
commit
e44ef891e9e68b6ce7d3fd3bac73b7d5433050ae upstream.
The MPIDR contains specific bitfields(MPIDR.Aff{2..0}) which uniquely
identify a CPU, in addition to some non-identifying information and
reserved bits. The ARM cpu binding defines the 'reg' property to only
contain the affinity bits, and any cpu nodes with other bits set in
their 'reg' entry are skipped.
As such it is not necessary to mask the phys_id with MPIDR_HWID_BITMASK,
and doing so could lead to matching erroneous CPU nodes in the device
tree. This patch removes the masking of the physical identifier.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jon Medhurst [Tue, 10 Dec 2013 10:18:58 +0000 (10:18 +0000)]
serial: amba-pl011: use port lock to guard control register access
commit
fe43390702a1b5741fdf217063b05c7612b38303 upstream.
When the pl011 is being used for a console, pl011_console_write forces
the control register (CR) to enable the UART for transmission and then
restores this to the original value afterwards. It does this while
holding the port lock.
Unfortunately, when the uart is started or shutdown - say in response to
userland using the serial device for a terminal - then this updates the
control register without any locking.
This means we can have
pl011_console_write Save CR
pl011_startup Initialise CR, e.g. enable receive
pl011_console_write Restore old CR with receive not enabled
this result is a serial port which doesn't respond to any input.
A similar race in reverse could happen when the device is shutdown.
We can fix these problems by taking the port lock when updating CR.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert Uytterhoeven [Tue, 21 Jan 2014 23:48:47 +0000 (15:48 -0800)]
mm: Make {,set}page_address() static inline if WANT_PAGE_VIRTUAL
commit
f92f455f67fef27929e6043499414605b0c94872 upstream.
{,set}page_address() are macros if WANT_PAGE_VIRTUAL. If
!WANT_PAGE_VIRTUAL, they're plain C functions.
If someone calls them with a void *, this pointer is auto-converted to
struct page * if !WANT_PAGE_VIRTUAL, but causes a build failure on
architectures using WANT_PAGE_VIRTUAL (arc, m68k and sparc64):
drivers/md/bcache/bset.c: In function `__btree_sort':
drivers/md/bcache/bset.c:1190: warning: dereferencing `void *' pointer
drivers/md/bcache/bset.c:1190: error: request for member `virtual' in something not a structure or union
Convert them to static inline functions to fix this. There are already
plenty of users of struct page members inside <linux/mm.h>, so there's
no reason to keep them as macros.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Mon, 6 Jan 2014 02:19:42 +0000 (13:19 +1100)]
md/raid5: Fix possible confusion when multiple write errors occur.
commit
1cc03eb93245e63b0b7a7832165efdc52e25b4e6 upstream.
commit
5d8c71f9e5fbdd95650be00294d238e27a363b5c
md: raid5 crash during degradation
Fixed a crash in an overly simplistic way which could leave
R5_WriteError or R5_MadeGood set in the stripe cache for devices
for which it is no longer relevant.
When those devices are removed and spares added the flags are still
set and can cause incorrect behaviour.
commit
14a75d3e07c784c004b4b44b34af996b8e4ac453
md/raid5: preferentially read from replacement device if possible.
Fixed the same bug if a more effective way, so we can now revert
the original commit.
Reported-and-tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Fixes:
5d8c71f9e5fbdd95650be00294d238e27a363b5c
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Mon, 13 Jan 2014 23:38:09 +0000 (10:38 +1100)]
md/raid10: fix two bugs in handling of known-bad-blocks.
commit
b50c259e25d9260b9108dc0c2964c26e5ecbe1c1 upstream.
If we discover a bad block when reading we split the request and
potentially read some of it from a different device.
The code path of this has two bugs in RAID10.
1/ we get a spin_lock with _irq, but unlock without _irq!!
2/ The calculation of 'sectors_handled' is wrong, as can be clearly
seen by comparison with raid1.c
This leads to at least 2 warnings and a probable crash is a RAID10
ever had known bad blocks.
Fixes:
856e08e23762dfb92ffc68fd0a8d228f9e152160
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Sun, 5 Jan 2014 23:35:34 +0000 (10:35 +1100)]
md/raid10: fix bug when raid10 recovery fails to recover a block.
commit
e8b849158508565e0cd6bc80061124afc5879160 upstream.
commit
e875ecea266a543e643b19e44cf472f1412708f9
md/raid10 record bad blocks as needed during recovery.
added code to the "cannot recover this block" path to record a bad
block rather than fail the whole recovery.
Unfortunately this new case was placed *after* r10bio was freed rather
than *before*, yet it still uses r10bio.
This is will crash with a null dereference.
So move the freeing of r10bio down where it is safe.
Fixes:
e875ecea266a543e643b19e44cf472f1412708f9
Reported-by: Damian Nowak <spam@nowaker.net>
URL: https://bugzilla.kernel.org/show_bug.cgi?id=68181
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NeilBrown [Wed, 11 Dec 2013 23:13:33 +0000 (10:13 +1100)]
md: fix problem when adding device to read-only array with bitmap.
commit
8313b8e57f55b15e5b7f7fc5d1630bbf686a9a97 upstream.
If an array is started degraded, and then the missing device
is found it can be re-added and a minimal bitmap-based recovery
will bring it fully up-to-date.
If the array is read-only a recovery would not be allowed.
But also if the array is read-only and the missing device was
present very recently, then there could be no need for any
recovery at all, so we simply include the device in the read-only
array without any recovery.
However... if the missing device was removed a little longer ago
it could be missing some updates, but if a bitmap is present it will
be conditionally accepted pending a bitmap-based update. We don't
currently detect this case properly and will include that old
device into the read-only array with no recovery even though it really
needs a recovery.
This patch keeps track of whether a bitmap-based-recovery is really
needed or not in the new Bitmap_sync rdev flag. If that is set,
then the device will not be added to a read-only array.
Cc: Andrei Warkentin <andreiw@vmware.com>
Fixes:
d70ed2e4fafdbef0800e73942482bb075c21578b
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paulo Zanoni [Wed, 8 Jan 2014 13:12:27 +0000 (11:12 -0200)]
drm/i915: fix DDI PLLs HW state readout code
commit
0882dae983707455e97479e5e904e37673517ebc upstream.
Properly zero the refcounts and crtc->ddi_pll_set so the previous HW
state doesn't affect the result of reading the current HW state.
This fixes WARNs about WRPLL refcount if we have an HDMI monitor on
HSW and then suspend/resume.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64379
Tested-by: Qingshuai Tian <qingshuai.tian@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Rohner [Wed, 15 Jan 2014 01:56:36 +0000 (17:56 -0800)]
nilfs2: fix segctor bug that causes file system corruption
commit
70f2fe3a26248724d8a5019681a869abdaf3e89a upstream.
There is a bug in the function nilfs_segctor_collect, which results in
active data being written to a segment, that is marked as clean. It is
possible, that this segment is selected for a later segment
construction, whereby the old data is overwritten.
The problem shows itself with the following kernel log message:
nilfs_sufile_do_cancel_free: segment 6533 must be clean
Usually a few hours later the file system gets corrupted:
NILFS: bad btree node (blocknr=8748107): level = 0, flags = 0x0, nchildren = 0
NILFS error (device sdc1): nilfs_bmap_last_key: broken bmap (inode number=114660)
The issue can be reproduced with a file system that is nearly full and
with the cleaner running, while some IO intensive task is running.
Although it is quite hard to reproduce.
This is what happens:
1. The cleaner starts the segment construction
2. nilfs_segctor_collect is called
3. sc_stage is on NILFS_ST_SUFILE and segments are freed
4. sc_stage is on NILFS_ST_DAT current segment is full
5. nilfs_segctor_extend_segments is called, which
allocates a new segment
6. The new segment is one of the segments freed in step 3
7. nilfs_sufile_cancel_freev is called and produces an error message
8. Loop around and the collection starts again
9. sc_stage is on NILFS_ST_SUFILE and segments are freed
including the newly allocated segment, which will contain active
data and can be allocated at a later time
10. A few hours later another segment construction allocates the
segment and causes file system corruption
This can be prevented by simply reordering the statements. If
nilfs_sufile_cancel_freev is called before nilfs_segctor_extend_segments
the freed segments are marked as dirty and cannot be allocated any more.
Signed-off-by: Andreas Rohner <andreas.rohner@gmx.net>
Reviewed-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Tested-by: Andreas Rohner <andreas.rohner@gmx.net>
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mikulas Patocka [Wed, 15 Jan 2014 01:56:40 +0000 (17:56 -0800)]
mm: fix crash when using XFS on loopback
commit
03e5ac2fc3bf6f4140db0371e8bb4243b24e3e02 upstream.
Commit
8456a648cf44 ("slab: use struct page for slab management") causes
a crash in the LVM2 testsuite on PA-RISC (the crashing test is
fsadm.sh). The testsuite doesn't crash on 3.12, crashes on 3.13-rc1 and
later.
Bad Address (null pointer deref?): Code=15 regs=
000000413edd89a0 (Addr=
000006202224647d)
CPU: 3 PID: 24008 Comm: loop0 Not tainted 3.13.0-rc6 #5
task:
00000001bf3c0048 ti:
000000413edd8000 task.ti:
000000413edd8000
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW:
00001000000001101111100100001110 Not tainted
r00-03
000000ff0806f90e 00000000405c8de0 000000004013e6c0 000000413edd83f0
r04-07
00000000405a95e0 0000000000000200 00000001414735f0 00000001bf349e40
r08-11
0000000010fe3d10 0000000000000001 00000040829c7778 000000413efd9000
r12-15
0000000000000000 000000004060d800 0000000010fe3000 0000000010fe3000
r16-19
000000413edd82a0 00000041078ddbc0 0000000000000010 0000000000000001
r20-23
0008f3d0d83a8000 0000000000000000 00000040829c7778 0000000000000080
r24-27
00000001bf349e40 00000001bf349e40 202d66202224640d 00000000405a95e0
r28-31
202d662022246465 000000413edd88f0 000000413edd89a0 0000000000000001
sr00-03
000000000532c000 0000000000000000 0000000000000000 000000000532c000
sr04-07
0000000000000000 0000000000000000 0000000000000000 0000000000000000
IASQ:
0000000000000000 0000000000000000 IAOQ:
00000000401fe42c 00000000401fe430
IIR:
539c0030 ISR:
00000000202d6000 IOR:
000006202224647d
CPU: 3 CR30:
000000413edd8000 CR31:
0000000000000000
ORIG_R28:
00000000405a95e0
IAOQ[0]: vma_interval_tree_iter_first+0x14/0x48
IAOQ[1]: vma_interval_tree_iter_first+0x18/0x48
RP(r2): flush_dcache_page+0x128/0x388
Backtrace:
flush_dcache_page+0x128/0x388
lo_splice_actor+0x90/0x148 [loop]
splice_from_pipe_feed+0xc0/0x1d0
__splice_from_pipe+0xac/0xc0
lo_direct_splice_actor+0x1c/0x70 [loop]
splice_direct_to_actor+0xec/0x228
lo_receive+0xe4/0x298 [loop]
loop_thread+0x478/0x640 [loop]
kthread+0x134/0x168
end_fault_vector+0x20/0x28
xfs_setsize_buftarg+0x0/0x90 [xfs]
Kernel panic - not syncing: Bad Address (null pointer deref?)
Commit
8456a648cf44 changes the page structure so that the slab
subsystem reuses the page->mapping field.
The crash happens in the following way:
* XFS allocates some memory from slab and issues a bio to read data
into it.
* the bio is sent to the loopback device.
* lo_receive creates an actor and calls splice_direct_to_actor.
* lo_splice_actor copies data to the target page.
* lo_splice_actor calls flush_dcache_page because the page may be
mapped by userspace. In that case we need to flush the kernel cache.
* flush_dcache_page asks for the list of userspace mappings, however
that page->mapping field is reused by the slab subsystem for a
different purpose. This causes the crash.
Note that other architectures without coherent caches (sparc, arm, mips)
also call page_mapping from flush_dcache_page, so they may crash in the
same way.
This patch fixes this bug by testing if the page is a slab page in
page_mapping and returning NULL if it is.
The patch also fixes VM_BUG_ON(PageSlab(page)) that could happen in
earlier kernels in the same scenario on architectures without cache
coherence when CONFIG_DEBUG_VM is enabled - so it should be backported
to stable kernels.
In the old kernels, the function page_mapping is placed in
include/linux/mm.h, so you should modify the patch accordingly when
backporting it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: John David Anglin <dave.anglin@bell.net>]
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Reviewed-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Helge Deller <deller@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qais Yousef [Wed, 15 Jan 2014 01:56:41 +0000 (17:56 -0800)]
crash_dump: fix compilation error (on MIPS at least)
commit
5a610fcc7390ee60308deaf09426ada87a1eeec2 upstream.
In file included from kernel/crash_dump.c:2:0:
include/linux/crash_dump.h:22:27: error: unknown type name `pgprot_t'
when CONFIG_CRASH_DUMP=y
The error was traced back to commit
9cb218131de1 ("vmcore: introduce
remap_oldmem_pfn_range()")
include <asm/pgtable.h> to get the missing definition
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt [Wed, 13 Nov 2013 20:20:04 +0000 (15:20 -0500)]
ftrace/x86: Load ftrace_ops in parameter not the variable holding it
commit
1739f09e33d8f66bf48ddbc3eca615574da6c4f6 upstream.
Function tracing callbacks expect to have the ftrace_ops that registered it
passed to them, not the address of the variable that holds the ftrace_ops
that registered it.
Use a mov instead of a lea to store the ftrace_ops into the parameter
of the function tracing callback.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Link: http://lkml.kernel.org/r/20131113152004.459787f9@gandalf.local.home
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hugh Dickins [Sun, 12 Jan 2014 09:25:21 +0000 (01:25 -0800)]
thp: fix copy_page_rep GPF by testing is_huge_zero_pmd once only
commit
eecc1e426d681351a6026a7d3e7d225f38955b6c upstream.
We see General Protection Fault on RSI in copy_page_rep: that RSI is
what you get from a NULL struct page pointer.
RIP: 0010:[<
ffffffff81154955>] [<
ffffffff81154955>] copy_page_rep+0x5/0x10
RSP: 0000:
ffff880136e15c00 EFLAGS:
00010286
RAX:
ffff880000000000 RBX:
ffff880136e14000 RCX:
0000000000000200
RDX:
6db6db6db6db6db7 RSI:
db73880000000000 RDI:
ffff880dd0c00000
RBP:
ffff880136e15c18 R08:
0000000000000200 R09:
000000000005987c
R10:
000000000005987c R11:
0000000000000200 R12:
0000000000000001
R13:
ffffea00305aa000 R14:
0000000000000000 R15:
0000000000000000
FS:
00007f195752f700(0000) GS:
ffff880c7fc20000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000093010000 CR3:
00000001458e1000 CR4:
00000000000027e0
Call Trace:
copy_user_huge_page+0x93/0xab
do_huge_pmd_wp_page+0x710/0x815
handle_mm_fault+0x15d8/0x1d70
__do_page_fault+0x14d/0x840
do_page_fault+0x2f/0x90
page_fault+0x22/0x30
do_huge_pmd_wp_page() tests is_huge_zero_pmd(orig_pmd) four times: but
since shrink_huge_zero_page() can free the huge_zero_page, and we have
no hold of our own on it here (except where the fourth test holds
page_table_lock and has checked pmd_same), it's possible for it to
answer yes the first time, but no to the second or third test. Change
all those last three to tests for NULL page.
(Note: this is not the same issue as trinity's DEBUG_PAGEALLOC BUG
in copy_page_rep with RSI:
ffff88009c422000, reported by Sasha Levin
in https://lkml.org/lkml/2013/3/29/103. I believe that one is due
to the source page being split, and a tail page freed, while copy
is in progress; and not a problem without DEBUG_PAGEALLOC, since
the pmd_same check will prevent a miscopy from being made visible.)
Fixes:
97ae17497e99 ("thp: implement refcounting for huge zero page")
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steven Rostedt [Fri, 10 Jan 2014 02:46:34 +0000 (21:46 -0500)]
SELinux: Fix possible NULL pointer dereference in selinux_inode_permission()
commit
3dc91d4338d698ce77832985f9cb183d8eeaf6be upstream.
While running stress tests on adding and deleting ftrace instances I hit
this bug:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000020
IP: selinux_inode_permission+0x85/0x160
PGD
63681067 PUD
7ddbe067 PMD 0
Oops: 0000 [#1] PREEMPT
CPU: 0 PID: 5634 Comm: ftrace-test-mki Not tainted 3.13.0-rc4-test-00033-gd2a6dde-dirty #20
Hardware name: /DG965MQ, BIOS MQ96510J.86A.0372.2006.0605.1717 06/05/2006
task:
ffff880078375800 ti:
ffff88007ddb0000 task.ti:
ffff88007ddb0000
RIP: 0010:[<
ffffffff812d8bc5>] [<
ffffffff812d8bc5>] selinux_inode_permission+0x85/0x160
RSP: 0018:
ffff88007ddb1c48 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
0000000000800000 RCX:
ffff88006dd43840
RDX:
0000000000000001 RSI:
0000000000000081 RDI:
ffff88006ee46000
RBP:
ffff88007ddb1c88 R08:
0000000000000000 R09:
ffff88007ddb1c54
R10:
6e6576652f6f6f66 R11:
0000000000000003 R12:
0000000000000000
R13:
0000000000000081 R14:
ffff88006ee46000 R15:
0000000000000000
FS:
00007f217b5b6700(0000) GS:
ffffffff81e21000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033^M
CR2:
0000000000000020 CR3:
000000006a0fe000 CR4:
00000000000007f0
Call Trace:
security_inode_permission+0x1c/0x30
__inode_permission+0x41/0xa0
inode_permission+0x18/0x50
link_path_walk+0x66/0x920
path_openat+0xa6/0x6c0
do_filp_open+0x43/0xa0
do_sys_open+0x146/0x240
SyS_open+0x1e/0x20
system_call_fastpath+0x16/0x1b
Code: 84 a1 00 00 00 81 e3 00 20 00 00 89 d8 83 c8 02 40 f6 c6 04 0f 45 d8 40 f6 c6 08 74 71 80 cf 02 49 8b 46 38 4c 8d 4d cc 45 31 c0 <0f> b7 50 20 8b 70 1c 48 8b 41 70 89 d9 8b 78 04 e8 36 cf ff ff
RIP selinux_inode_permission+0x85/0x160
CR2:
0000000000000020
Investigating, I found that the inode->i_security was NULL, and the
dereference of it caused the oops.
in selinux_inode_permission():
isec = inode->i_security;
rc = avc_has_perm_noaudit(sid, isec->sid, isec->sclass, perms, 0, &avd);
Note, the crash came from stressing the deletion and reading of debugfs
files. I was not able to recreate this via normal files. But I'm not
sure they are safe. It may just be that the race window is much harder
to hit.
What seems to have happened (and what I have traced), is the file is
being opened at the same time the file or directory is being deleted.
As the dentry and inode locks are not held during the path walk, nor is
the inodes ref counts being incremented, there is nothing saving these
structures from being discarded except for an rcu_read_lock().
The rcu_read_lock() protects against freeing of the inode, but it does
not protect freeing of the inode_security_struct. Now if the freeing of
the i_security happens with a call_rcu(), and the i_security field of
the inode is not changed (it gets freed as the inode gets freed) then
there will be no issue here. (Linus Torvalds suggested not setting the
field to NULL such that we do not need to check if it is NULL in the
permission check).
Note, this is a hack, but it fixes the problem at hand. A real fix is
to restructure the destroy_inode() to call all the destructor handlers
from the RCU callback. But that is a major job to do, and requires a
lot of work. For now, we just band-aid this bug with this fix (it
works), and work on a more maintainable solution in the future.
Link: http://lkml.kernel.org/r/20140109101932.0508dec7@gandalf.local.home
Link: http://lkml.kernel.org/r/20140109182756.17abaaa8@gandalf.local.home
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Fri, 13 Dec 2013 20:21:26 +0000 (04:21 +0800)]
writeback: Fix data corruption on NFS
commit
f9b0e058cbd04ada76b13afffa7e1df830543c24 upstream.
Commit
4f8ad655dbc8 "writeback: Refactor writeback_single_inode()" added
a condition to skip clean inode. However this is wrong in WB_SYNC_ALL
mode because there we also want to wait for outstanding writeback on
possibly clean inode. This was causing occasional data corruption issues
on NFS because it uses sync_inode() to make sure all outstanding writes
are flushed to the server before truncating the inode and with
sync_inode() returning prematurely file was sometimes extended back
by an outstanding write after it was truncated.
So modify the test to also check for pages under writeback in
WB_SYNC_ALL mode.
Fixes:
4f8ad655dbc82cf05d2edc11e66b78a42d38bf93
Reported-and-tested-by: Dan Duval <dan.duval@oracle.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare [Tue, 14 Jan 2014 14:59:55 +0000 (15:59 +0100)]
hwmon: (coretemp) Fix truncated name of alarm attributes
commit
3f9aec7610b39521c7c69d754de7265f6994c194 upstream.
When the core number exceeds 9, the size of the buffer storing the
alarm attribute name is insufficient and the attribute name is
truncated. This causes libsensors to skip these attributes as the
truncated name is not recognized.
Reported-by: Andreas Hollmann <hollmann@in.tum.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Warren [Mon, 13 Jan 2014 21:29:04 +0000 (14:29 -0700)]
i2c: Re-instate body of i2c_parent_is_i2c_adapter()
commit
2fac2b891f287691c27ee8d2eeecf39571b27fea upstream.
The body of i2c_parent_is_i2c_adapter() is currently guarded by
I2C_MUX. It should be CONFIG_I2C_MUX instead.
Among potentially other problems, this resulted in i2c_lock_adapter()
only locking I2C mux child adapters, and not the parent adapter. In
turn, this could allow inter-mingling of mux child selection and I2C
transactions, which could result in I2C transactions being directed to
the wrong I2C bus, and possibly even switching between busses in the
middle of a transaction.
One concrete issue caused by this bug was corrupted HDMI EDID reads
during boot on the NVIDIA Tegra Seaboard system, although this only
became apparent in recent linux-next, when the boot timing was changed
just enough to trigger the race condition.
Fixes:
3923172b3d70 ("i2c: reduce parent checking to a NOOP in non-I2C_MUX case")
Cc: Phil Carmody <phil.carmody@partner.samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>