media: i2c: Add ov7251_pll_configure()

Rather than having the pll settings hidden inside mode blobs, define
them in structs and use a dedicated function to set them. This makes
it simpler to extend the driver to support other frequencies for both
the external clock and desired link frequency.

Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: Remove per-mode frequencies from ov7251

Each of the defined modes in the ov7251 driver uses the same link
frequency and pixel rate; just drop those members of the modes and
set the controls to read only during initialisation. Add a new
table defining the supported pixel rates to substitue for the values
hardcoded in the modes.

Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: Provide ov7251_check_hwcfg()

Move the endpoint checking from .probe() to a dedicated function,
and additionally check that the firmware provided link frequencies
are a match for those supported by the driver. Store the index to the
matching link frequency so it can be easily identified later.

Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: Add acpi support to ov7251

Add support for enumeration through ACPI to the ov7251 driver

Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ipu3-cio2: Add support for V4L2_PIX_FMT_IPU3_Y10

We have platforms where a camera sensor transmits Y10 data to
the CIO2 device - add support for that (packed) format to the
ipu3-cio2 driver.

Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: uapi: Add IPU3 packed Y10 format

Some platforms with an Intel IPU3 have an IR sensor producing 10 bit
greyscale format data that is transmitted over a CSI-2 bus to a CIO2
device - this packs the data into 32 bytes per 25 pixels. Add an entry
to the uAPI header defining that format.

Signed-off-by: Daniel Scally <djrscally@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5645: Remove unneeded of_match_ptr macro

of_match_ptr isn't required as CONFIG_OF is already a dependency in Kconfig

Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov8856: apply digital gain by setting global gain control register

MWB gain register are used to set gain for each mwb channel mannually.
However, it will involve some artifacts if gain cannot be applied to
each channel synchronously. Enable global gain control to set digital
global gain instead of setting AWB gain separately to fix this issue.

Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov5648: fix wrong pointer passed to IS_ERR() and PTR_ERR()

IS_ERR() and PTR_ERR() use wrong pointer, it should be
sensor->dovdd, fix it.

Fixes: e43ccb0a045f ("media: i2c: Add support for the OV5648 image sensor")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Documentation: mc: Add media_device_{init,cleanup}

Document that drivers must first initialise a media device before
registering it, and clean up once the media device is unregistered.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Add MIPI CSI-2 28 bits per pixel raw data type

Add CSI-2 data type for 28 bits per pixel data.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: ov2640: Depend on V4L2_ASYNC

Add V4L2_ASYNC as a dependency to match other drivers and prevent failures
when compile testing.

Fixes: ff3cc65cadb5 ("media: v4l: async, fwnode: Improve module organisation")
Signed-off-by: Mike Pagano <mpagano@gentoo.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: video-i2c: Use GENMASK for masking bits

Replace 0x0380 with GENMASK(9, 7) to obtain 0b0000_0011_1000_0000

Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: video-i2c: Replace constants with proper names

Acc to MLX90640 datasheet:
 - 0x0400 represents the start of RAM address
 - 0x2400 represents the start of EEPROM address

Reference: https://www.melexis.com/-/media/files/documents\
           /datasheets/mlx90640-datasheet-melexis.pdf

Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: video-i2c: Move defines to the top of the file

Currently, the defines in this driver are after some structs and
functions, it makes more sense to move them up to the top of the file,
so that the constants can be named together with other defines.

Signed-off-by: Moses Christopher Bollavarapu <mosescb.dev@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: exynos4-is: Fix compile warning

Declare static on function 'fimc_isp_video_device_unregister'.

When VIDEO_EXYNOS4_ISP_DMA_CAPTURE=n, compiler warns about
warning: no previous prototype for function [-Wmissing-prototypes]

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kwanghoon Son <k.son@samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: adv7180: Add support for the test patterns

ADV7180 has a built-in mechanism to generate some video patterns,
which is very useful for debug/bring-up activities.

Add support for it.

The test_pattern parameter can be one of the following values:

0: "Single color"
1: "Color bars"
2: "Luma ramp"
3: "Boundary box"
4: "Disable"

Tested on a imx6q board with an ADV7280.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ti: cal: use frame desc to get vc and dt

Use get_frame_desc() to get the frame desc from the connected source,
and use the provided virtual channel and datatype instead of hardcoded
ones.

get_frame_desc() can contain multiple streams, but as we don't support
multiple streams yet, we will just always use the first stream.

If the source doesn't support get_frame_desc(), fall back to the
previous method of always capturing virtual channel 0 and any datatype.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Add CSI-2 bus configuration to frame descriptors

Add CSI-2 bus specific configuration to the frame descriptors. This allows
obtaining the virtual channel and data type information for each stream
the transmitter is sending.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: Add bus type to frame descriptors

Add the media bus type to the frame descriptor. CSI-2 specific
information will be added in next patch to the frame descriptor.

- Make the bus type a named enum

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: media: video-interfaces: Add new bus-type

No properly bus-type for DPI video bus, add bus-type 7 for it.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: media/v4l2-core: Add enum V4L2_FWNODE_BUS_TYPE_DPI

As V4L2_FWNODE_BUS_TYPE_PARALLEL is not used for DPI interface, this
patch add V4L2_FWNODE_BUS_TYPE_DPI for video DPI interface.

Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ov7670: remove ov7670_power_off from ov7670_remove

In ov7670_probe, it always invokes ov7670_power_off() no matter
the execution is successful or failed. So we cannot invoke it
agiain in ov7670_remove().

Fix this by removing ov7670_power_off from ov7670_remove.

Fixes: 030f9f682e66 ("media: ov7670: control clock along with power")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dw9807-vcm: Add "dongwoon,dw9807" compatible string

There is firmware out there that uses "dongwoon,dw9807" compatible string
that never made it to upstream as-is. Add it to the driver to make it load
on such systems.

The chip also has an EEPROM part which is AT24 compatible (for reading
purposes) on a separate I²C address. Adding possible support for this in
the future is not affected by this change.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: Convert Dongwoon dw9807-vcm bindings to json-schema

Convert the old text based dw9807-vcm chip DT bindings to json-schema.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: imx412: Add bulk regulator support

Depending on the platform we may need to enable and disable three separate
regulators for the imx412.

- DOVDD
Digital I/O power

- AVDD
Analog power

- DVDD
Digital core power

The addition of these regulators shouldn't affect existing users using
fixed-on/firmware-controlled regulators.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: imx412: Add regulator descriptions

The imx412 like many I2C camera sensors has three voltage rails which
depending on platform may be necessary to switch power onto directly.

Add in as optional rails so as not to break anything for existing users.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: imx412: Fix power_off ordering

The enable path does
- gpio
- clock

The disable path does
- gpio
- clock

Fix the order on the power-off path so that power-off and power-on have the
same ordering for clock and gpio.

Fixes: 9214e86c0cc1 ("media: i2c: Add imx412 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: i2c: imx412: Fix reset GPIO polarity

The imx412/imx577 sensor has a reset line that is active low not active
high. Currently the logic for this is inverted.

The right way to define the reset line is to declare it active low in the
DTS and invert the logic currently contained in the driver.

The DTS should represent the hardware does i.e. reset is active low.
So:
+               reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
not:
-               reset-gpios = <&tlmm 78 GPIO_ACTIVE_HIGH>;

I was a bit reticent about changing this logic since I thought it might
negatively impact @intel.com users. Googling a bit though I believe this
sensor is used on "Keem Bay" which is clearly a DTS based system and is not
upstream yet.

Fixes: 9214e86c0cc1 ("media: i2c: Add imx412 camera sensor driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: h264: Avoid wrapping long_term_frame_idx

For long term references, frame_num is set to long_term_frame_idx which
does not require wrapping. This is fixed by observation, no directly
related issue have been found yet.

Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-mem2mem: Trace on implicit un-hold

If the timestamp of the src buffer differs from the timestamp of a held
dst buffer, the held buffer is implicitly removed and marked as done.
Add a trace to help debugging if someone hits that case.

Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: doc: Document dual use of H.264 pic_num/frame_num

These two fields need documentation as they have dual meaning. It is also
confusing since pic_num is a derived value from frame_num, so this should
help application developers. If we ever need to make a V2 of this API, I
would suggest to remove pic_num entirely.

Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Sebastian Fricke <sebastian.fricke@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: add h264 decoder driver for mt8186

Add h264 decode driver to support mt8186. For the architecture
is single core, need to add new interface to decode.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Support MT8186

Adds MT8186's compatible "mediatek,mt8186-vcodec-dec".
Adds MT8186's device private data mtk_vdec_single_core_pdata.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: media: mediatek: vcodec: Adds decoder dt-bindings for mt8186

Adds decoder dt-bindings for mt8186.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: prevent kernel crash when rmmod mtk-vcodec-dec.ko

If the driver support subdev mode, the parameter "dev->pm.dev" will be
NULL in mtk_vcodec_dec_remove. Kernel will crash when try to rmmod
mtk-vcodec-dec.ko.

[ 4380.702726] pc : do_raw_spin_trylock+0x4/0x80
[ 4380.707075] lr : _raw_spin_lock_irq+0x90/0x14c
[ 4380.711509] sp : ffff80000819bc10
[ 4380.714811] x29: ffff80000819bc10 x28: ffff3600c03e4000 x27: 0000000000000000
[ 4380.721934] x26: 0000000000000000 x25: 0000000000000000 x24: 0000000000000000
[ 4380.729057] x23: ffff3600c0f34930 x22: ffffd5e923549000 x21: 0000000000000220
[ 4380.736179] x20: 0000000000000208 x19: ffffd5e9213e8ebc x18: 0000000000000020
[ 4380.743298] x17: 0000002000000000 x16: ffffd5e9213e8e90 x15: 696c346f65646976
[ 4380.750420] x14: 0000000000000000 x13: 0000000000000001 x12: 0000000000000040
[ 4380.757542] x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
[ 4380.764664] x8 : 0000000000000000 x7 : ffff3600c7273ae8 x6 : ffffd5e9213e8ebc
[ 4380.771786] x5 : 0000000000000000 x4 : 0000000000000001 x3 : 0000000000000000
[ 4380.778908] x2 : 0000000000000000 x1 : ffff3600c03e4000 x0 : 0000000000000208
[ 4380.786031] Call trace:
[ 4380.788465]  do_raw_spin_trylock+0x4/0x80
[ 4380.792462]  __pm_runtime_disable+0x2c/0x1b0
[ 4380.796723]  mtk_vcodec_dec_remove+0x5c/0xa0 [mtk_vcodec_dec]
[ 4380.802466]  platform_remove+0x2c/0x60
[ 4380.806204]  __device_release_driver+0x194/0x250
[ 4380.810810]  driver_detach+0xc8/0x15c
[ 4380.814462]  bus_remove_driver+0x5c/0xb0
[ 4380.818375]  driver_unregister+0x34/0x64
[ 4380.822288]  platform_driver_unregister+0x18/0x24
[ 4380.826979]  mtk_vcodec_dec_driver_exit+0x1c/0x888 [mtk_vcodec_dec]
[ 4380.833240]  __arm64_sys_delete_module+0x190/0x224
[ 4380.838020]  invoke_syscall+0x48/0x114
[ 4380.841760]  el0_svc_common.constprop.0+0x60/0x11c
[ 4380.846540]  do_el0_svc+0x28/0x90
[ 4380.849844]  el0_svc+0x4c/0x100
[ 4380.852975]  el0t_64_sync_handler+0xec/0xf0
[ 4380.857148]  el0t_64_sync+0x190/0x194
[ 4380.860801] Code: 94431515 17ffffca d503201f d503245f (b9400004)

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: support stateless VP9 decoding

Add support for VP9 decoding using the stateless API,
as supported by MT8192. And the drivers is lat and core architecture.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: George Sun <george.sun@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: support stateless VP8 decoding

Add support for VP8 decoding using the stateless API,
as supported by MT8192.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: support stateless H.264 decoding for mt8192

Adds h264 lat and core architecture driver for mt8192,
and the decode mode is frame based for stateless decoder.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Extract H264 common code

Mt8192 can use some of common code with mt8183. Moves them to
a new file in order to reuse.

[hverkuil: replaced memcpy_toio by memcpy, was left over from a prev version]

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: record capture queue format type

The capture queue format type may be differ depending on platform: for
stateless decoder drivers, we need to calculate the capture buffer size
according to the capture queue format type in SCP.

As a preparation for introducing drivers for stateless decoding, save the
current capture queue type on a per vcodec context basis.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Fix v4l2-compliance fail

Need to use default pic info when get pic info fail.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Steve Cho <stevecho@chromium.org>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: disable vp8 4K capability

For vp8 not support 4K, need to disable it.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Add format to support MT21C

Needs to use mediatek compressed mode for mt8192 decoder.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Getting supported decoder format types

Getting supported output and capture queue format types according
to decoder capability.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Refactor supported vdec formats and framesizes

Supported output and capture format types for mt8192 are different
with mt8183. Redefine parameters to store them.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Refactor get and put capture buffer flow

For lat and core decode in parallel, need to get capture buffer
when core start to decode and put capture buffer to display
list when core decode done.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: set each plane bytesused in buf prepare

call vb2_set_plane_payload to set each plane bytesused in buf prepare,
need not to set independently for stateless and statefull architectures.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Read max resolution from dec_capability

Supported max resolution for different platforms are not the same: 2K
or 4K, getting it according to dec_capability.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih<tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: get capture queue buffer size from scp

Different capture buffer format has different buffer size, need to get
real buffer size according to buffer type from scp.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Using firmware type to separate different firmware architecture

MT8173 platform use vpu firmware, mt8183/mt8192 will use scp
firmware instead, using chip name is not reasonable to separate
different firmware architecture. Using firmware type is much better.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih<tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Add vdec enable/disable hardware helpers

Lock, power and clock are highly coupled operations. Adds vdec
enable/disable hardware helpers and uses them.

Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih<tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: mediatek: vcodec: Fix v4l2 compliance decoder cmd test fail

Will return -EINVAL using standard framework api when test stateless
decoder with cmd VIDIOC_(TRY)DECODER_CMD. Disable them to adjust v4l2
compliance test for user driver(GStreamer/Chrome) won't use decoder cmd.

Fixes: 8cdc3794b2e3 ("media: mtk-vcodec: vdec: support stateless API")
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-adap.c: drop activate_cnt, use state info instead

Using an activation counter to decide when the enable or disable the
cec adapter is not the best approach and can lead to race conditions.

Change this to determining the current status of the adapter, and
enable or disable the adapter accordingly.

It now only needs to be called whenever there is a chance that the
state changes, and it can handle enabling/disabling monitoring as
well if needed.

This simplifies the code and it should be a more robust approach as well.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-adap.c: reconfigure if the PA changes during configuration

If the physical address changes (i.e. becomes invalid, then valid again)
while the adapter is still claiming free logical addresses, then trigger
a reconfiguration since any claimed LAs may now be stale.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-adap.c: fix is_configuring state

If an adapter is trying to claim a free logical address then it is
in the 'is_configuring' state. If during that process the cable is
disconnected (HPD goes low, which in turn invalidates the physical
address), then cec_adap_unconfigure() is called, and that set the
is_configuring boolean to false, even though the thread that's
trying to claim an LA is still running.

Don't touch the is_configuring bool in cec_adap_unconfigure(), it
will eventually be cleared by the thread. By making that change
the cec_config_log_addr() function also had to change: it was
aborting if is_configuring became false (since that is what
cec_adap_unconfigure() did), but that no longer works. Instead
check if the physical address is invalid. That is a much
more appropriate check anyway.

This fixes a bug where the the adapter could be disabled even
though the device was still configuring. This could cause POLL
transmits to time out.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-adap.c: stop trying LAs on CEC_TX_STATUS_TIMEOUT

If, while trying to claim a free logical address, a POLL message
times out, then abort this process. A CEC_TX_STATUS_TIMEOUT
should be handled the same as a CEC_TX_STATUS_ABORTED.

This avoids a situation where transmits time out due to a
driver or hardware bug and it takes ages before the attempt
to find available free logical addresses finishes.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-adap.c: don't unconfigure if already unconfigured

The __cec_s_log_addrs() function can configure or unconfigure the
adapter. The ioctl handler in cec-api.c will prevent it from being
called to configure the adapter if it was already configured (or in
the process of configuring). But it can still be called to unconfigure
an already unconfigured adapter, and it didn't check for that.

This can cause cec_activate_cnt_dec() to be called too often, causing
a WARN_ON.

Instead first check if adap->log_addrs.num_log_addrs == 0 and return
since in that case the adapter is already unconfigured.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-pin.c: don't zero work_pin_num_events in adap_enable

It's OK to keep the pending pin events when disabling or
enabling the 'adapter'. Zeroing this can cause a race condition
if this happens when the pin kthread is handling a pin event
and calls atomic_dec later, causing work_pin_num_events to become
negative.

Just leave pending events in the queue, they'll be read eventually.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cec-pin.c: disabling the adapter cannot call kthread_stop

When the adap_enable callback is called the adap->lock is held.
When disabling the adapter it attempts to stop the kthread that
deals with receiving and transmitting messages. However, kthread_stop
waits for the thread to stop, so all that time adap->lock is held.

Unfortunately, the kernel thread itself can call functions that take
that same lock, so a deadlock can occur.

Change the logic to keep the kernel thread running and instead when
disabling the adapter, just set the pin to high, go to idle and then
to state OFF and disable the interrupt. Only stop the kernel thread
when the adapter is deleted.

This way disabling the adapter will not wait for anything and the
deadlock is avoided.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: imon: reorganize serialization

Since usb_register_dev() from imon_init_display() from imon_probe() holds
minor_rwsem while display_open() which holds driver_lock and ictx->lock is
called with minor_rwsem held from usb_open(), holding driver_lock or
ictx->lock when calling usb_register_dev() causes circular locking
dependency problem.

Since usb_deregister_dev() from imon_disconnect() holds minor_rwsem while
display_open() which holds driver_lock is called with minor_rwsem held,
holding driver_lock when calling usb_deregister_dev() also causes circular
locking dependency problem.

Sean Young explained that the problem is there are imon devices which have
two usb interfaces, even though it is one device. The probe and disconnect
function of both usb interfaces can run concurrently.

Alan Stern responded that the driver and USB cores guarantee that when an
interface is probed, both the interface and its USB device are locked.
Ditto for when the disconnect callback gets run. So concurrent probing/
disconnection of multiple interfaces on the same device is not possible.

Therefore, we don't need locks for handling race between imon_probe() and
imon_disconnect(). But we still need to handle race between display_open()
/vfd_write()/lcd_write()/display_close() and imon_disconnect(), for
disconnect event can happen while file descriptors are in use.

Since "struct file"->private_data is set by display_open(), vfd_write()/
lcd_write()/display_close() can assume that "struct file"->private_data
is not NULL even after usb_set_intfdata(interface, NULL) was called.

Replace insufficiently held driver_lock with refcount_t based management.
Add a boolean flag for recording whether imon_disconnect() was already
called. Use RCU for accessing this boolean flag and refcount_t.

Since the boolean flag for imon_disconnect() is shared, disconnect event
on either intf0 or intf1 affects both interfaces. But I assume that this
change does not matter, for usually disconnect event would not happen
while interfaces are in use.

Link: https://syzkaller.appspot.com/bug?extid=c558267ad910fc494497
Reported-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Tested-by: syzbot <syzbot+c558267ad910fc494497@syzkaller.appspotmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: imon: drop references only after device is no longer used

The point of using get/put_device() is to keep references
for as long as the device may be in use. That means dropping
them must be the penultimate action right before freeing the memory.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: imon: fix timer racing disconnect

The timer will report events for an input device.
Reporting events for an unregistered device is bad.
Hence the timer must be killed first.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: imon: avoid needless atomic allocations in resume

GFP_NOIO is fine here.

Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: s5k6a3: add missing clk_disable_unprepare

Fix smatch warning:

drivers/media/i2c/s5k6a3.c:234 __s5k6a3_power_on() warn: 'sensor->clock' from clk_prepare_enable() not released on lines: 234.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: ccs-core.c: fix failure to call clk_disable_unprepare

Fixes smatch warning:

drivers/media/i2c/ccs/ccs-core.c:1676 ccs_power_on() warn: 'sensor->ext_clk' from clk_prepare_enable() not released on lines: 1606.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cx25821: request_irq -> devm_request_irq

Fixes smatch warning:

drivers/media/pci/cx25821/cx25821-alsa.c:768 cx25821_audio_initdev() warn: 'dev->pci->irq' from request_irq() not released on lines: 768.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: videobuf2-dma-sg.c: kvmalloc_array -> kvcalloc

Fixes smatch warning:

drivers/media/common/videobuf2/videobuf2-dma-sg.c:129 vb2_dma_sg_alloc() warn: Please consider using kvcalloc instead

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-ctls-core.c: kvmalloc_array -> kvcalloc

Fixes smatch warning:

drivers/media/v4l2-core/v4l2-ctrls-core.c:1143 v4l2_ctrl_handler_init_class() warn: Please consider using kvcalloc instead

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: v4l2-subdev.c: kvmalloc_array -> kvcalloc

Fixes smatch warning:

drivers/media/v4l2-core/v4l2-subdev.c:978 __v4l2_subdev_state_alloc() warn: Please consider using kvcalloc instead

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hantro: HEVC: unconditionnaly set pps_{cb/cr}_qp_offset values

Always set pps_cb_qp_offset and pps_cr_qp_offset values in Hantro/G2
register whatever is V4L2_HEVC_PPS_FLAG_PPS_SLICE_CHROMA_QP_OFFSETS_PRESENT
flag value.
The vendor code does the same to set these values.
This fixes conformance test CAINIT_G_SHARP_3.

Fluster HEVC score is increase by one with this patch.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hantro: HEVC: Fix reference frames management

PoC shall be int the range of -2^31 to 2^31 -1
(HEVC spec section 8.3.1 Decoding process for picture order count).
The current way to know if an entry in reference picture array is free
is to test if PoC = UNUSED_REF. Since UNUSED_REF is defined as '-1' that
could lead to decode issue if one PoC also equal '-1'.
PoC with value = '-1' exists in conformance test SLIST_B_Sony_9.

Change the way unused entries are managed in reference pictures array to
avoid using PoC to detect then.

This patch doesn't change fluster HEVC score.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hantro: HEVC: Fix tile info buffer value computation

Use pps->column_width_minus1[j] + 1 as value for the tile info buffer
instead of pps->column_width_minus1[j + 1].
The patch fixes DBLK_E_VIXS_2, DBLK_F_VIXS_2, DBLK_G_VIXS_2,
SAO_B_MediaTek_5, TILES_A_Cisco_2 and TILES_B_Cisco_1 tests in fluster.

Fixes: cb5dd5a0fa51 ("media: hantro: Introduce G2/HEVC decoder")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hantro: HEVC: Fix output frame chroma offset

Hantro decoder doesn't take care of the requested and aligned size
of the capture buffer.
Stop using the bitstream width/height and use capture frame size
stored in the context to get the correct values.

hantro_hevc_chroma_offset() and hantro_hevc_motion_vectors_offset()
are only used in hantro_g2_hevc_dec.c so take the opportunity
to move them here.

fluster HEVC score goes up from 77 to 85 successful tests (over 147)
with this patch.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: hantro: Use post processor scaling capacities

Hantro G2 post processor is able to down scale decoded frames
by a factor of 2, 4 or 8.
Add enum_framesizes() ops to postproc_ops structure to enumerate the
possible output sizes for a given input resolution.
For G2 post-processor use fsize->index (from 0 to 3) as power of 2
divisor. As described in v4l2 documentation return -EINVAL when scaling
down isn't possible.

fluster scores:
77/147 for HEVC
143/303 for VP9

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: amphion: G/S_PARM only for encoder's output queue

G/S_PARM doesn't make sense for the capture queue of a stateful encoder,
unless V4L2_FMT_FLAG_ENC_CAP_FRAME_INTERVAL is set to reserve hardware
resources.

Otherwise it will fail the v4l2-compliance

Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: amphion: wake up when error occurs

when error occurs, driver set error flag,
and driver need to wake up the poll wait

Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: microchip-csi2dc: add link validation support

With this, the csi2dc will take part in the media pipeline graph walk
and validate the links with it's entities.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dt-bindings: media: microchip,xisc: add bus-width of 14

The Microchip XISC supports a bus width of 14 bits.
Add it to the supported bus widths.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-sama7g5-isc: remove stray line

Remove stray line from formats struct.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-isc: compact the controller formats list

Compact the list array to be more readable.
No other changes, only cosmetic.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-isc-base: use mutex to lock awb workq from streaming

The AWB workqueue runs in a kernel thread and needs to be synchronized
w.r.t. the streaming status.
It is possible that streaming is stopped while the AWB workq is running.
In this case it is likely that the check for vb2_start_streaming_called is
done at one point in time, but the AWB computations are done later,
including a call to isc_update_profile, which requires streaming to be
started.
Thus , isc_update_profile will fail if during this operation sequence the
streaming was stopped.
To solve this issue, a mutex is added, that will serialize the awb work and
streaming stopping, with the mention that either streaming is stopped
completely including termination of the last frame is done, and after that
the AWB work can check stream status and stop; either first AWB work is
completed and after that the streaming can stop correctly.
The awb spin lock cannot be used since this spinlock is taken in the same
context and using it in the stop streaming will result in a recursion BUG.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-sama5d2-isc: fix wrong mask in YUYV format check

While this does not happen in production, this check should be done
versus the mask, as checking with the YCYC value may not include
some bits that may be set.
It is correct and safe to check the whole mask.

Fixes: 123aaf816b95 ("media: atmel: atmel-sama5d2-isc: fix YUYV format")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-isc: remove redundant comments

Remove duplicate comments which are already in place before the struct
definition.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-isc-base: replace is_streaming call in s_fmt_vid_cap

In s_fmt_vid_cap, we should check if vb2_is_busy and return EBUSY,
not check if it's streaming to return the busy state.

Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atmel: atmel-isc-base: use streaming status when queueing buffers

During experiments with libcamera, it looks like vb2_is_streaming returns
true before our start streaming is called.
Order of operations is streamon -> queue -> start_streaming
ISC would have started the DMA immediately when a buffer is being added
to the vbqueue if the queue is streaming.
It is more safe to start the DMA after the start streaming of the driver is
called.
Thus, even if vb2queue is streaming, add the buffer to the dma queue of the
driver instead of actually starting the DMA process, if the start streaming
has not been called yet.
Tho achieve this, we have to use vb2_start_streaming_called instead of
vb2_is_streaming.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: vsp1: Fix offset calculation for plane cropping

The vertical subsampling factor is currently not considered in the
offset calculation for plane cropping done in rpf_configure_partition.
This causes a distortion (shift of the color plane) when formats with
the vsub factor larger than 1 are used (e.g. NV12, see
vsp1_video_formats in vsp1_pipe.c). This commit considers vsub factor
for all planes except plane 0 (luminance).

Drop generalization of the offset calculation to reduce the binary size.

Fixes: e5ad37b64de9 ("[media] v4l: vsp1: Add cropping support")
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Signed-off-by: LUU HOAI <hoai.luu.ub@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: vsp1: Use vb2_queue_is_busy()

Use the new vb2_queue_is_busy() helper to replace the open-coded
version.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: vsp1: Don't open-code vb2_fop_release()

Use the vb2_fop_release() helper to replace the open-coded version. The
video->lock is assigned to the queue lock, used by vb2_fop_release(), so
the only functional difference is that v4l2_fh_release() is now called
before vsp1_device_put(). This should be harmless.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: videobuf2-v4l2: Expose vb2_queue_is_busy() to drivers

vb2 queue ownership is managed by the ioctl handler helpers
(vb2_ioctl_*). There are however use cases where drivers can benefit
from checking queue ownership, for instance when open-coding an ioctl
handler that needs to perform additional checks before calling the
corresponding vb2 operation.

Expose the vb2_queue_is_busy() function in the videobuf2-v4l2.h header,
and change its first argument to a struct vb2_queue pointer as the
function name implies it operates on a queue, not a video_device.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: rockchip: rkisp1: Use mipi-csi2.h

Replace the driver-specific definitions of MIPI CSI-2 data types with
macros from mipi-csi2.h.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: cadence: cdns-csi2tx: Use mipi-csi2.h

Replace the hardcoded MIPI CSI-2 data types with macros from
mipi-csi2.h.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: atomisp: don't pass a pointer to a local variable

As warned by gcc 12.1:

drivers/staging/media/atomisp/pci/runtime/rmgr/src/rmgr_vbuf.c: In function 'ia_css_rmgr_acq_vbuf':
drivers/staging/media/atomisp/pci/runtime/rmgr/src/rmgr_vbuf.c:275:33: error: storing the address of local variable 'h' in '*handle' [-Werror=dangling-pointer=]
  275 |                         *handle = &h;
      |                         ~~~~~~~~^~~~
drivers/staging/media/atomisp/pci/runtime/rmgr/src/rmgr_vbuf.c:257:40: note: 'h' declared here
  257 |         struct ia_css_rmgr_vbuf_handle h;
      |                                        ^
drivers/staging/media/atomisp/pci/runtime/rmgr/src/rmgr_vbuf.c:257:40: note: 'handle' declared here
cc1: all warnings being treated as errors

The logic uses a temporary struct to update the handler, but,
instead of copying the value to the pointer sent by the caller, it
replaces it with the content with a local variable. That's wrong, and
may lead the caller to use a weird value.

Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: amphion: ensure the buffer count is not less than min_buffer

the output buffer count should >= min_buffer_out
the capture buffer count should >= min_buffer_cap

Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: stkwebcam: move stk_camera_read_reg() scratch buffer to struct stk_camera

In stk_camera_read_reg() a single byte buffer is alloc-ed and
freed on every function call.  Since the size is known,
move the buffer to the struct stk_camera where it will be alloc-ed
and freed once.

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: coda: limit frame interval enumeration to supported encoder frame sizes

Let VIDIOC_ENUM_FRAMEINTERVALS return -EINVAL if userspace queries
frame intervals for frame sizes unsupported by the encoder. Fixes the
following v4l2-compliance failure:

fail: v4l2-test-formats.cpp(123): found frame intervals for invalid size 47x16
fail: v4l2-test-formats.cpp(282): node->codec_mask & STATEFUL_ENCODER
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL

[hverkuil: drop incorrect 'For decoder devices, return -ENOTTY.' in the commit log]

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: coda: fix default JPEG colorimetry

Set default colorspace to SRGB for JPEG encoder and decoder devices,
to fix the following v4l2-compliance test failure:

test VIDIOC_TRY_FMT: OK
fail: v4l2-test-formats.cpp(818): fmt_raw.g_colorspace() != V4L2_COLORSPACE_SRGB

Also explicitly set transfer function, YCbCr encoding and quantization
range, as required by v4l2-compliance for the JPEG encoded side.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: isif: remove unnecessary check of res

The resource is checked in probe function, so there is
no need do this check in remove function.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dm644x_ccdc: remove unnecessary check of res

The resource is checked in probe function, so there is
no need do this check in remove function.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

media: dm355_ccdc: remove unnecessary check of res

The resource is checked in probe function, so there is
no need do this check in remove function.

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>