drm/amdgpu: Unify PSP TA context

Remove all TA binary structures and add the specific binary
structure in struct ta_context.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: move iommu_resume before ip init/resume

Separate iommu_resume from kfd_resume, and move it before
other amdgpu ip init/resume.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add amdgpu_amdkfd_resume_iommu

Add amdgpu_amdkfd_resume_iommu for amdgpu.

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: separate kfd_iommu_resume from kfd_resume

Separate kfd_iommu_resume from kfd_resume for fine-tuning
of amdgpu device init/resume/reset/recovery sequence.

v2: squash in fix for !CONFIG_HSA_AMD

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=211277
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu:  Get atomicOps info from Host for sriov setup

The AtomicOp Requester Enable bit is reserved in VFs and the PF value applies to all
associated VFs. so guest driver can not directly enable the atomicOps for VF, it
depends on PF to enable it. In current design, amdgpu driver  will get the enabled
atomicOps bits through private pf2vf data

Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Enable mem low power control for DCN3.1 sub-IP blocks

[WHY]
Sequences to handle powering down these sub-IP blocks are now ready for use

Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove force_enable_edp_fec param.

Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Ian Chen <ian.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add VPG and AFMT low power support for DCN3.1

[WHY]
Power down VPG and AFMT blocks when not in use

[HOW]
Create afmt31 and vpg31 structs and add necessary fields to reg list

Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert adding degamma coefficients

[Why]
Degamma coefficients are calculated in our degamma formula using
the regamma coefficients. We do not need to add separate degamma
coefficients.

[How]
Remove the change to add separate degamma coefficients.

Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Link training retry fix for abort case

[Why]
If link training is aborted, it shall be retried if sink is present.

[How]
Check hpd status to find out whether sink is present or not. If sink is
present, then link training shall be tried again with same settings.
Otherwise, link training shall be aborted.

Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix unstable HPCP compliance on Chrome Barcelo

[Why]
Intermittently, there presents two occurrences of 0 stream
commits in a single HPD event. Current HDCP sequence does
not consider such scenerio, and will thus disable HDCP.

[How]
Add condition check to include stream remove and re-enable
case for HDCP enable.

Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.152

* Correct degamma coefficients
* Optimize bandwidth on following fast update
* Fix multiple memory leaks reported by coverity
* Get backlight from PWM if DMCU is not initialized

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Correct degamma coefficients

[Why]
Some incorrect coefficients were being used

Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.82

* PSR SMU optimizations
* MST dock fixes

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add periodic detection when zstate is enabled

[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.

[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: dsc mst 2 4K displays go dark with 2 lane HBR3

[Why]
call stack of amdgpu dsc mst pbn, slot num calculation is as below:
-compute_bpp_x16_from_target_bandwidth
-decide_dsc_target_bpp_x16
-setup_dsc_config
-dc_dsc_compute_bandwidth_range
-compute_mst_dsc_configs_for_link
-compute_mst_dsc_configs_for_state

from pbn -> dsc target bpp_x16

bpp_x16 is calulated by compute_bpp_x16_from_target_bandwidth.
Beside pixel clock and bpp, num_slices_h and bpp_increment_div
will also affect bpp_x16.

from dsc target bpp_x16 -> pbn

within dm_update_mst_vcpi_slots_for_dsc,
pbn = drm_dp_calc_pbn_mode(clock, bpp_x16, true);

drm_dp_calc_pbn_mode(int clock, int bpp, bool dsc)
{
  return DIV_ROUND_UP_ULL(mul_u32_u32(clock * (bpp / 16), 64 * 1006),
            8 * 54 * 1000 * 1000);
}

bpp / 16 trunc digits after decimal point. This will cause calculation
delta. drm_dp_calc_pbn_mode does not have other informations,
like num_slices_h, bpp_increment_div. therefore, it does not do revese
calcuation properly from bpp_x16 to pbn.

pbn from drm_dp_calc_pbn_mode is less than pbn from
compute_mst_dsc_configs_for_state. This cause not enough mst slot
allocated to display. display could not visually light up.

[How]
pass pbn from compute_mst_dsc_configs_for_state to
dm_update_mst_vcpi_slots_for_dsc

Cc: stable@vger.kernel.org
Reviewed-by: Scott Foster <Scott.Foster@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Refine condition of cursor visibility for pipe-split

[Why]
In some scenarios like fullscreen game, major plane is scaled. Then
if a upper layer owns the cursor, cursor is invisiable in the
majority of the screen.

[How]
Instead assuming upper plane handles cursor, summing up upper
split planes on the same layer. If whole upper plane covers current
half/whole pipe plane, disable cursor.

Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Optimize bandwidth on following fast update

[Why]
The current call to optimize_bandwidth never occurs because flip is
always pending from the FULL and FAST updates.

[How]
Optimize on the following flip when it's a FAST update and we know we
aren't going to be modifying the clocks again.

Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Apply w/a for hard hang on HPD

[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans under 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enablement, causing DMUB to access an irresponsive PHY
and thus a hard hang on the system.

[How]
Disable 48mhz refclk off when there is any HPD status in
connected state.

Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add regamma/degamma coefficients and set sRGB when TF is BT709

[Why]
In YUV case, need to set the input TF to sRGB instead of BT709,
even though the input TF type is distributed. SRGB was not
being used because pixel format was not being set in the
surface update sequence.
Also, we were using the same coefficients for degamma and
regamma formula, causing the cutoff point of the linear
section of the curve to be incorrect.

[How]
Set pixel format in the surface update sequence. Add separate
coefficient arrays for regamma and degamma.

Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jaehyun Chung <jaehyun.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert "Directly retrain link from debugfs"

This reverts commit f5b6a20c7ef40599095c796b0500d842ffdbc639.

This patch broke new settings from taking effect. Hotplug is
required for new settings to take effect.

Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Get backlight from PWM if DMCU is not initialized

On Carrizo/Stoney systems we set backlight through panel_cntl, i.e.
directly via the PWM registers, if DMCU is not initialized. We
always read it back through ABM registers which leads to a
mismatch and forces atomic_commit to program the backlight
each time.

Instead make sure we use the same logic for backlight readback,
i.e. read it from panel_cntl if DMCU is not initialized.

We also need to remove some extraneous and incorrect calculations
at the end of dce_get_16_bit_backlight_from_pwm.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1666
Cc: stable@vger.kernel.org
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix multiple memory leaks reported by coverity

coccinelle patch used:

@@ expression enc1,vpg,afmt; @@
-       if (!enc1 || !vpg || !afmt)
+       if (!enc1 || !vpg || !afmt) {
+               kfree(enc1);
+               kfree(vpg);
+               kfree(afmt);
                return NULL;
+       }

Addresses-Coverity-ID: 1466017: ("Resource leaks")

Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.151

* coverity kernel memory leak fixes
* NULL pointer dereference fixes
* Add periodic detection when zstate is enabled
* Fork thread to offload work of hpd_rx_irq

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Revert "dc: w/a for hard hang on HPD on native DP"

This reverts commit "drm/amd/display: w/a for hard hang on HPD on native DP".

[How & Why]
Revert change as it does not fix the hard hang
in all cases. An alternative w/a will be submitted
separately.

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.81

* PSR optimizations
* add support for ABM when ODM is enabled
* Z10 with PSR fixes
* Increase trace buffer

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix for null pointer access for ddc pin and aux engine.

[Why]
Need a check for NULL pointer access for ddc pin and aux engine.

[How]
Adding a check for ddc pin and aux engine accesses.

Reviewed-by: Jimmy Kizito <jimmy.kizito@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix false BAD_FREE warning from Coverity

This is an attempt to fix false warning raised by Coverity
via multiple CID's.

Addresses-Coverity-ID: 1487412 ("Free of address-of expression")
Cc: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Wesley Chalmers <wesley.chalmers@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix dynamic link encoder access.

[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.

[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.

Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add flag to detect dpms force off during HPD

[Why] When a connector is unplugged, dpms is forced off so that some
connector allocations are cleared off. This is done outside the commit
sequence from the userspace. This causes HUBP blank. Due to the blank
hubp, a non blocking commit which queues flip will encounter a timeout
waiting for the flip_done because prior to writing the surface flip
address, hubp was in blank.

[How] Add a marker to DM's crtc state and use this field to indicate
whether dpms was forced off during an HPD. Check for this marker before
queuing the flip.

Reviewed-by: Anson Jacob <Anson.Jacob@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: unblock abm when odm is enabled only on configs that support it

[Why]
When ODM is enabled, ABM is blocked on dcn31 but unblocked on dcn30.

Since the dcn31 firmware is now able to handle ABM interop with ODM, it
is no longer necessary to block ABM when ODM is enabled.

Since the dcn30 firmware does not handle ABM interop with ODM, leaving
that combination unblocked can lead to one side of the screen appearing
brighter than the other.

[How]
When ODM is enabled, unblock abm on dcn31 and block it on dcn30

Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fork thread to offload work of hpd_rx_irq

[Why]
Currently, we will try to get dm.dc_lock in handle_hpd_rx_irq() when
link lost happened, which is risky and could cause deadlock.
e.g. If we are under procedure to enable MST streams and then monitor
happens to toggle short hpd to notify link lost, then
handle_hpd_rx_irq() will get blocked due to stream enabling flow has
dc_lock. However, under MST, enabling streams involves communication
with remote sinks which need to use handle_hpd_rx_irq() to handle
sideband messages. Thus, we have deadlock here.

[How]
Target is to have handle_hpd_rx_irq() finished as soon as possilble.
Hence we can react to interrupt quickly. Besides, we should avoid to
grabe dm.dc_lock within handle_hpd_rx_irq() to avoid deadlock situation.

Firstly, revert patches which introduced to use dm.dc_lock in
handle_hpd_rx_irq():

* commit ("drm/amd/display: NULL pointer error during ")

* commit ("drm/amd/display: Only one display lights up while using MST")

* commit ("drm/amd/display: take dc_lock in short pulse handler only")

Instead, create work to handle irq events which needs dm.dc_lock.
Besides:

* Create struct hpd_rx_irq_offload_work_queue for each link to handle
  its short hpd events

* Avoid to handle link lost/ automated test if the link is disconnected

* Defer dc_lock needed works in dc_link_handle_hpd_rx_irq(). This
  function should just handle simple stuff for us (e.g. DPCD R/W).
  However, deferred works should still be handled by the order that
  dc_link_handle_hpd_rx_irq() used to be.

* Change function name dm_handle_hpd_rx_irq() to
  dm_handle_mst_sideband_msg() to be more specific

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add option to defer works of hpd_rx_irq

[Why & How]
Due to some code flow constraints, we need to defer dc_lock needed works
from dc_link_handle_hpd_rx_irq(). Thus, do following changes:

* Change allow_hpd_rx_irq() from static to public
* Change handle_automated_test() from static to public
* Extract link lost handling flow out from dc_link_handle_hpd_rx_irq()
  and put those into a new function dc_link_dp_handle_link_loss()
* Add one option parameter to decide whether defer works within
  dc_link_handle_hpd_rx_irq()

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: update conditions to do dfp cap ext validation

[why]
According to DP specs dfp cap ext validation is only for branch
device withou 128b/132b channel coding support and
downstream of the branch device doesn't have compression.
Therefore we are adding conditions to only do dfp cap
extension validation for branch devcie supporting 8b/10b
channel coding only and it has no DSC passthrough capability.

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: move bpp range decision in decide dsc bw range function

[why]
Before get dsc bw range is used to compute DSC bw range
based on the given fixed bpp min/max input.
The new change will merge any specs, signal, timing specific
bpp range decision into this function. So the function needs to make
a decision with all aspects considered.

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix system hang at boot

[Why]
During DQE's promotion test, system hang issue is found on linux
system;

[How]
1. Add NULL pointor check for the link in the sequence trace
   function;
2. Get the right link for the stream encoder before blank DP
   stream;

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DPCD writes at key points

This reverts commit "Revert "Add DPCD writes at key points" ".
The following patch will fix the system hang issue.

v2: squash in indentation warning fix

Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: expose dsc overhead bw in dc dsc header

[why]
DM needs to know how much overhead is added to DSC as result
of AMD internal DSC limitation.

Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: make needs_pcie_atomics FW-version dependent

On some GPUs the PCIe atomic requirement for KFD depends on the MEC
firmware version. Add a firmware version check for this. The minimum
firmware version that works without atomics can be updated in the
device_info structure for each GPU type.

Move PCIe atomic detection from kgd2kfd_probe into kgd2kfd_device_init
because the MEC firmware is not loaded yet at the probe stage.

Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Increase direct IB pool size

Direct IB pool is used for vce/vcn IB extra msg too. Increase its size
to AMDGPU_IB_POOL_SIZE.

v2: Squash in unused variable removal

Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add manual sclk/vddc setting support for cyan skilfish(v3)

Add manual sclk/vddc setting supoort via pp_od_clk_voltage sysfs
to maintain consistency with other asics. As cyan skillfish doesn't
support DPM, there is only a single frequency and voltage to adjust.

v2: maintain consistency and add command guide.
v3: adjust user settings storage and coding style.

Command guide:
echo vc point sclk vddc > pp_od_clk_voltage
"vc"    - sclk voltage curve
"point" - must be 0
"sclk"  - target value of sclk(MHz), should be in safe range
"vddc"  - target value of vddc(mV), a 6.25(mV) stepping is
  recommended and should be in safe range (the real
  vddc is an approximation of target value)
echo c > pp_od_clk_voltage
"c" - commit the changes of sclk and vddc, only after
  the commit command, the target values set by "vc"
  command will take effect
echo r > pp_od_clk_voltage
"r"  - reset sclk and vddc to default value, a subsequent
  commit command is needed to take effect

Example:
1) Check default sclk and vddc
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 862mV *
OD_RANGE:
SCLK:    1000Mhz       2000Mhz
VDDC:     700mV        1129mV
2) Set sclk to 1500MHz and vddc to 700mV
$ echo vc 0 1500 700 > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1500Mhz *
OD_VDDC:
0: 693mV *
OD_RANGE:
SCLK:    1000Mhz       2000Mhz
VDDC:     700mV        1129mV
3) Reset sclk and vddc to default
$ echo r > pp_od_clk_voltage
$ echo c > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 1800Mhz *
OD_VDDC:
0: 874mV *
OD_RANGE:
SCLK:    1000Mhz       2000Mhz
VDDC:     700mV        1129mV
NOTE:
We don't specify an explicit safe range, you can set any values
between min and max at your own risk. Enjoy!

Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add some pptable funcs for cyan skilfish(v3)

Add print_clk_levels and read_sensor pptable funcs for
cyan skilfish.

v2: keep consitency and add get_gpu_metrics callback.
v3: use sysfs_emit_at() in sysfs show function.

Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update SMU driver interface for cyan skilfish(v3)

Add SmuMetrics_t definition for cyan skilfish.

v2: update SmuMetrics_t definition.
v3: cleanup and rearrange the order of fields.

Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update SMU PPSMC for cyan skilfish

Add some PPSMC MSGs for cyan skilfish.

Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix sysfs_emit/sysfs_emit_at warnings(v2)

sysfs_emit and sysfs_emit_at requrie a page boundary
aligned buf address. Make them happy!

v2: use an inline function.

Warning Log:
[  492.545174] invalid sysfs_emit_at: buf:00000000f19bdfde at:0
[  492.546416] WARNING: CPU: 7 PID: 1304 at fs/sysfs/file.c:765 sysfs_emit_at+0x4a/0xa0
[  492.654805] Call Trace:
[  492.655353]  ? smu_cmn_get_metrics_table+0x40/0x50 [amdgpu]
[  492.656780]  vangogh_print_clk_levels+0x369/0x410 [amdgpu]
[  492.658245]  vangogh_common_print_clk_levels+0x77/0x80 [amdgpu]
[  492.659733]  ? preempt_schedule_common+0x18/0x30
[  492.660713]  smu_print_ppclk_levels+0x65/0x90 [amdgpu]
[  492.662107]  amdgpu_get_pp_od_clk_voltage+0x13d/0x190 [amdgpu]
[  492.663620]  dev_attr_show+0x1d/0x40

Signed-off-by: Lang Yu <lang.yu@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: dc_assert_fp_enabled assert only if FPU is not enabled

Assert only when FPU is not enabled.

Fixes: 0ea7ee821701 ("drm/amd/display: Add DC_FP helper to check FPU state")
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Update RAS trigger error block support

Added trigger error support for MP0/MP1/MPIO blocks

Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Update RAS status print

Remove uncessary RAS status prints

Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: refactor function to init no-psp fw

Refactor the code of amdgpu_ucode_init_single_fw to make it more
readable as too many ucode need to handle on this function currently.

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add NULL checks for vblank workqueue

[Why]
If we're running a headless config with 0 links then the vblank
workqueue will be NULL - causing a NULL pointer exception during
any commit.

[How]
Guard access to the workqueue if it's NULL and don't queue or flush
work if it is.

Reported-by: Mike Lothian <mike@fireburn.co.uk>
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1700
Fixes: 58aa1c50e5a231 ("drm/amd/display: Use vblank control events for PSR enable/disable")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Enable some sysnodes for guest smi

Enable sysnode vclk and dclk on Navi21 asic for guest smi

Signed-off-by: Roy Sun <Roy.Sun@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: cleanup debugfs for amdgpu rings

Use debugfs_create_file_size API for creating ring debugfs, and as its a
NULL returning API, change the return type for amdgpu_debugfs_ring_init
API as well. Also cleanup surrounding code.

Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use IS_ERR for debugfs APIs

debugfs APIs returns encoded error so use
IS_ERR for checking return value.

v2: return PTR_ERR(ent)

References: https://gitlab.freedesktop.org/drm/amd/-/issues/1686
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-By: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: make configure_lttpr_mode_transparent and configure_lttpr_mode_non_transparent static

This symbols is not used outside of dc_link_dp.c, so marks it static.

Fix the following sparse warning:

drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1766:16:
warning: symbol 'configure_lttpr_mode_non_transparent' was not declared.
Should it be static?

drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1755:16:
warning: symbol 'configure_lttpr_mode_transparent' was not declared.
Should it be static?

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix warning comparing pointer to 0

Fix the following coccicheck warning:

./drivers/gpu/drm/amd/display/dc/clk_mgr/dcn31/dcn31_clk_mgr.c:643:35-36:
WARNING comparing pointer to 0.

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: chongjiapeng <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/ci_dpm: Remove redundant initialization of variables hi_sidd, lo_sidd

The variables hi_sidd and lo_sidd are being initialized with a values
that are never read, they are being updated later on. The assignments
are redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amd/display: downgrade validation failure log level

In amdgpu_dm_atomic_check, dc_validate_global_state is called. On
failure this logs a warning to the kernel journal. However warnings
shouldn't be used for atomic test-only commit failures: user-space
might be perfoming a lot of atomic test-only commits to find the
best hardware configuration.

Downgrade the log to a regular DRM atomic message. While at it, use
the new device-aware logging infrastructure.

This fixes error messages in the kernel when running gamescope [1].

[1]: https://github.com/Plagman/gamescope/issues/245

Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Harry Wentland <hwentlan@amd.com>
Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: Prefer kcalloc over open coded arithmetic

As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.

So, refactor the code a bit to use the purpose specific kcalloc()
function instead of the calculated size argument in the kzalloc()
function.

[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments

Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: sdma: clean up identation

There is a statement that is indented incorrectly. Clean it up.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: clean up inconsistent indenting

There are a couple of statements that are indented one character
too deeply, clean these up.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: remove unused amdgpu_bo_validate

Just drop some dead code.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix use after free during BO move

The memory backing old_mem is already freed at that point, move the
check a bit more up.

Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: bfa3357ef9ab ("drm/ttm: allocate resource object instead of embedding it v2")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1699
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Create common PSP TA load function

Creat common PSP TA load function and update PSP ta_mem_context
with size information.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: fix the issue of uploading powerplay table

fix the issue of uploading powerplay table due to the dependancy of rlc.

Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: Increase HWIP_MAX_INSTANCE to 10

Seems like newer cards can have even more instances now.
Found by UBSAN: array-index-out-of-bounds in
drivers/gpu/drm/amd/amdgpu/amdgpu_discovery.c:318:29
index 8 is out of range for type 'uint32_t *[8]'

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1697
Cc: stable@vger.kernel.org
Signed-off-by: Ernst Sjöstrand <ernstp@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix unused initialization of pointer sink

Pointer sink is being inintialized with a value that is never read,
it is later being re-assigned a new value. Remove the redundant
initialization.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: Update navi12 smu message mapping table in sriov

[Why]
Sending invalid SMU message in sriov cause set dpm level fail.

[How]
Update message table based on SMU firmware.

Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Review-by: Horace Chen <Horace.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu:schedule vce/vcn encode based on priority

Schedule the encode job in VCE/VCN encode ring
based on the priority set by UMD.

Signed-off-by: Satyajit Sahu <satyajit.sahu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vcn: set the priority for each encode ring

VCN has multiple rings. Set the proper priority level for each
encode ring while initializing.

Signed-off-by: Satyajit Sahu <satyajit.sahu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vce: set the priority for each ring

VCE has multiple rings. Set the proper priority level for each
ring while initializing.

Signed-off-by: Satyajit Sahu <satyajit.sahu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: add mpio to ras block

Add MPIO to RAS block

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: consolidate PSP TA unload function

Create common PSP TA unload function and replace all common TA unloading
sequences.

Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/amdgpu: New debugfs interface for MMIO registers (v5)

This new debugfs interface uses an IOCTL interface in order to pass
along state information like SRBM and GRBM bank switching.  This
new interface also allows a full 32-bit MMIO address range which
the previous didn't.  With this new design we have room to grow
the flexibility of the file as need be.

(v2): Move read/write to .read/.write, fix style, add comment
      for IOCTL data structure

(v3): C style comments

(v4): use u32 in struct and remove offset variable

(v5): Drop flag clearing in op function, use 0xFFFFFFFF for broadcast
      instead of 0x3FF, use mutex for op/ioctl.

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix spelling mistake "alidation" -> "validation"

There is a spelling mistake in a DC_LOG_WARNING message. Fix it.

Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: detach ring priority from gfx priority

Currently AMDGPU_RING_PRIO_MAX is redefinition of a
max gfx hwip priority, this won't work well when we will
have a hwip with different set of priorities than gfx.
Also, HW ring priorities are different from ring priorities.

Create a global enum for ring priority levels which each
HWIP can use to define its own priority levels.

Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: rework context priority handling

To get a hardware queue priority for a context, we are currently
mapping AMDGPU_CTX_PRIORITY_* to DRM_SCHED_PRIORITY_* and then
to hardware queue priority, which is not the right way to do that
as DRM_SCHED_PRIORITY_* is software scheduler's priority and it is
independent from a hardware queue priority.

Use userspace provided context priority, AMDGPU_CTX_PRIORITY_* to
map a context to proper hardware queue priority.

Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.150

This version brings along following fixes:
- FW promotion 0.0.80
- Add missing ABM register offsets
- Fix in swizzle mode mapping
- Emulated sink support for freesync
- Improvoments in max target bpp

Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.80

- Add volatile to avoid incomplete flushing of data in rb

Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Update swizzle mode enums

[Why]
Swizzle mode enum for DC_SW_VAR_R_X was existing,
but not mapped correctly.

[How]
Update mapping and conversion for DC_SW_VAR_R_X.

Reviewed-by: XiangBing Foo <XiangBing.Foo@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Initialize GSP1 SDP header

[Why + How]
Initialize GSP1 SDP header for use in DMCUB FW.

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add emulated sink support for updating FS

[Why]
When forced modes are used during certain IGT tests,
without a real connector, dc_sink would be null when
standard modes are added by the driver. Calling the
function to update freesync capabilities at this
point will result in an error being printed

[How]
Use emulated sink when available. If both the normal
and emulated sink are not available, set all freesync
parameters to 0.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Limit max DSC target bpp for specific monitors

[Why]
Some monitors exhibit corruption at 16bpp DSC.

[How]
- Add helpers for patching edid caps.
- Use it for limiting DSC target bitrate to 15bpp for known monitors

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Cc: stable@vger.kernel.org
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Use max target bpp override option

[Why]
Max target bpp override is an option for working around
DSC issues. It is supported on DC level, but was not
used in DM.

[How]
Use actual option value instead of 0.

Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Set min dcfclk if pipe count is 0

[WHY]
Clocks don't get recalculated in 0 stream/0 pipe configs,
blocking S0i3 if dcfclk gets high enough

[HOW]
Create DCN31 copy of DCN30 bandwidth validation func which
doesn't entirely skip validation in 0 pipe scenarios

Override dcfclk to vlevel 0/min value during validation if pipe
count is 0

Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Support for DMUB HPD interrupt handling

[WHY]
To add support for HPD interrupt handling from DMUB.
HPD interrupt could be triggered from outbox1 from DMUB

[HOW]
1) Use queue_work to handle hpd task from outbox1

2) Add handle_hpd_irq_helper to share interrupt handling code
between legacy and DMUB HPD from outbox1

3) Added DMUB HPD handling in dmub_srv_stat_get_notification().
HPD handling callback function and wake up the DMUB thread.

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add missing ABM register offsets

[Why]
Some ABM registers don't exist on DCN 3.01, so are
missing from its register offset list. However,
this list was copied to later versions of DCN that
do have these registers. As a result, they're
inaccessible from the driver on those DCN versions
even though they exist.

[How]
Add the missing ABM register offsets to DCN 3.02+

Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 SST DC Support

1. Retrieve 128/132b link cap.
2. 128/132b link training and payload allocation.
3. UHBR10 link rate support.

[squash in warning fixes - Alex]

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 BIOS and DMUB Support

Parse DP2 encoder caps and hpo instance from bios

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 DCCG

HW Blocks:

        +--------+  +-----+  +------+
        |  OPTC  |  | HDA |  | HUBP |
        +--------+  +-----+  +------+
            |          |        |
            |          |        |
    HPO ====|==========|========|====
     |      |          v        |
     |      |       +-----+     |
     |      |       | APG |     |
     |      |       +-----+     |
     |      |          |        |
     |      v          v        v
     |     +---------------------+
     |     |  HPO Stream Encoder |
     |     +---------------------+
     |                 |
     |                 v
     |      +--------------------+
     |      |  HPO Link Encoder  |
     |      +--------------------+
     |                 |
     v  ===============|=============
                       v
              +------------------+
              |  DIO Output Mux  |
              +------------------+
                       |
                       v
                    +-----+
                    | PHY |
                    +-----+
                       | PHYD32CLK[0]
                       v
                    +------+
                    | DCCG |
                    +------+
                       |
                       v
                   SYMCLK32

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 HPO Link Encoder

HW Blocks:

        +--------+  +-----+  +------+
        |  OPTC  |  | HDA |  | HUBP |
        +--------+  +-----+  +------+
            |          |        |
            |          |        |
    HPO ====|==========|========|====
     |      |          v        |
     |      |       +-----+     |
     |      |       | APG |     |
     |      |       +-----+     |
     |      |          |        |
     |      v          v        v
     |     +---------------------+
     |     |  HPO Stream Encoder |
     |     +---------------------+
     |                 |
     |                 v
     |      +--------------------+
     |      |  HPO Link Encoder  |
     v      +--------------------+

[squash in warning fixes - Alex]

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 HPO Stream Encoder

HW Blocks:

        +--------+  +-----+  +------+
        |  OPTC  |  | HDA |  | HUBP |
        +--------+  +-----+  +------+
            |          |        |
            |          |        |
    HPO ====|==========|========|====
     |      |          v        |
     |      |       +-----+     |
     |      |       | APG |     |
     |      |       +-----+     |
     |      |          |        |
     v      v          v        v
           +----------------------+
           |  HPO Stream Encoder  |
           +----------------------+

[squash in warning fixes - Alex]

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add DP 2.0 Audio Package Generator

HW Blocks:

                    +-----+
                    | HDA |
                    +-----+
                       |
                       |
    HPO ===============|=============
     |                 v
     |              +-----+
     |              | APG |
     v              +-----+

Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdkfd: drop process ref count when xnack disable

During svm restore pages interrupt handler, kfd_process ref count was
never dropped when xnack was disabled. Therefore, the object was never
released.

Fixes: 2383f56bbe4a ("drm/amdkfd: page table restore through svm API")
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: enable more pm sysfs under SRIOV 1-VF mode

Enable pp_num_states, pp_cur_state, pp_force_state, pp_table sysfs under
SRIOV 1-VF scenario.

Signed-off-by: Jiawei Gu <Jiawei.Gu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix fdinfo race with process exit

Get process vm root BO ref in case process is exiting and root BO is
freed, to avoid NULL pointer dereference backtrace:

BUG: unable to handle kernel NULL pointer dereference at
0000000000000000
Call Trace:
amdgpu_show_fdinfo+0xfe/0x2a0 [amdgpu]
seq_show+0x12c/0x180
seq_read+0x153/0x410
vfs_read+0x91/0x140[ 3427.206183]  ksys_read+0x4f/0xb0
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca

Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Fix a deadlock if previous GEM object allocation fails

Fall through to handle the error instead of return.

Fixes: f8aab60422c37 ("drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs")
Cc: stable@vger.kernel.org
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: stop scheduler when calling hw_fini (v2)

This gurantees no more work on the ring can be submitted
to hardware in suspend/resume case, otherwise a potential
race will occur and the ring will get no chance to stay
empty before suspend.

v2: Call drm_sched_resubmit_job before drm_sched_start to
restart jobs from the pending list.

Suggested-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

drm/amdgpu: Clear RAS interrupt status on aldebaran

Resolve incorrect register address

Reviewed-by: Candice Li <candice.li@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Initialize lt_settings on instantiation

[WHY]
lt_settings' pointers remain uninitialized but nonzero if display fails
to light up with no DPCD/EDID info populated, leading to a hang on access

Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: cleanup idents after a revert

[WHY]
The change has caused high idle memory clock speed and power
consumption at some resolutions and frame rates for Navi10

[HOW]
Reverted change "drm/amd/display: Fixed Intermittent blue
screen on OLED panel"

Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Angus Wang <angus.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>