Minkyu Kang [Mon, 17 May 2010 04:17:44 +0000 (13:17 +0900)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Stefano Babic [Tue, 16 Mar 2010 16:22:21 +0000 (17:22 +0100)]
Add SPI support to mx51evk board
The patch adds SPI devices to the mx51evk board.
The MC13892 chip (PMIC) is supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Sun, 18 Apr 2010 17:27:44 +0000 (19:27 +0200)]
MX: Added definition file for MC13892
The MC13892 is a Power Controller used with processors
of the family MX.51. The file adds definitions to be used to setup
the internal registers via SPI.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Sun, 4 Apr 2010 20:43:38 +0000 (22:43 +0200)]
SPI: added support for MX51 to mxc_spi
This patch add SPI support for the MX51 processor.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Fri, 16 Apr 2010 15:13:54 +0000 (17:13 +0200)]
MX31: Add support for PMIC to the QONG module
Add support for the PMIC (MC13783) controller
and enables charging of the RTC battery.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Fri, 16 Apr 2010 15:11:19 +0000 (17:11 +0200)]
MX: RTC13783 uses general function to access PMIC
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
Stefano Babic [Sun, 4 Apr 2010 21:08:03 +0000 (23:08 +0200)]
MX: Added Freescale Power Management Driver
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Magnus Lilja [Fri, 23 Apr 2010 18:30:49 +0000 (20:30 +0200)]
i.MX31: Activate NAND support for i.MX31 Litekit board.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Fabio Estevam [Fri, 23 Apr 2010 13:32:01 +0000 (06:32 -0700)]
MX51: Fix MX51 CPU detect message
Fix MX51 CPU detect message.
Original string was:
CPU: Freescale i.MX51 family 3.0V at 800 MHz
which can be misinterpreted as 3.0 Volts instead of the silicon revision.
,change it to:
CPU: Freescale i.MX51 family rev3.0 at 800 MHz
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Stefano Babic [Sun, 18 Apr 2010 18:01:01 +0000 (20:01 +0200)]
MX51evk: Removed warnings
Changes reflect modifications in the fsl_esdhc driver
(the clk_enable field war removed in the configuration structure).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Anatolij Gustschin [Wed, 21 Apr 2010 11:52:38 +0000 (13:52 +0200)]
tx25: fix crash while booting Linux
Currently booting Linux on TX25 board doesn't work
since there is no correct mach-id and boot parameters
setup for tx25 board. Fix it now.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Minkyu Kang [Mon, 10 May 2010 06:20:50 +0000 (15:20 +0900)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
arch/arm/include/asm/mach-types.h
common/serial.c
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Tom [Sun, 9 May 2010 21:58:11 +0000 (16:58 -0500)]
ARM Update mach-types
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with
repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit
257dab81413b31b8648becfe11586b3a41e5c29a
Signed-off-by: Tom <Tom@bumblecow.com>
Asen Dimov [Mon, 19 Apr 2010 11:18:43 +0000 (14:18 +0300)]
pm9263 converted to at91 soc access
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Asen Dimov [Mon, 19 Apr 2010 11:17:22 +0000 (14:17 +0300)]
at91: define matrix registers bit fields
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Stefano Babic [Tue, 13 Apr 2010 10:19:06 +0000 (12:19 +0200)]
MX31: Removed erroneous board name from QONG
QONG is a module that can be installed on several boards,
not only on the QONG-EVB manufactured by Dave srl.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Thu, 8 Apr 2010 15:23:52 +0000 (17:23 +0200)]
MX31: Add UBI support to QONG module
The UBI/UBIFS support is added to the QONG module.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 31 Mar 2010 08:27:47 +0000 (10:27 +0200)]
MX31: Support 128MB RAM on QONG module
The QONG module can be downsized and delivered
with 128MB instead of 256MB. The patch adds
run time support for the two different memory
configurations.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 29 Mar 2010 14:43:39 +0000 (16:43 +0200)]
MX31: Add support for NAND to QONG board
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 29 Mar 2010 13:56:10 +0000 (15:56 +0200)]
MX31: add pin definitions for NAND controller
Add pin definitions ralted to the NAND controller to be used
to set up the pin multiplexer.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Tue, 13 Apr 2010 10:07:00 +0000 (12:07 +0200)]
MX31: add accessor function to get a gpio
The patch adds an accessor function to get the value of a gpio.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Tue, 13 Apr 2010 10:38:43 +0000 (12:38 +0200)]
mx51evk: correct list of possible BOOT_FROM values
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Tue, 13 Apr 2010 10:38:22 +0000 (12:38 +0200)]
mkimage: correct spelling error in imximage
Signed-off-by: Stefano Babic <sbabic@denx.de>
John Rigby [Thu, 8 Apr 2010 05:30:09 +0000 (23:30 -0600)]
MX25 print arm clock instead of mpllclk on boot
Replace call to imx_get_mpllclk with imx_get_armclk
to show frequency of ARM core instead of mpll internal
bus in print_cpuinfo.
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
Frans Meulenbroeks [Tue, 6 Apr 2010 13:36:11 +0000 (19:06 +0530)]
configs/openrd_base.h: reordered macros
moved CONFIG_CMD_FAT to filesystem section
swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Frans Meulenbroeks [Tue, 6 Apr 2010 12:56:19 +0000 (18:26 +0530)]
configs/sheevaplug: added a few additional commands
This patch includes a few additional commands in the sheevaplug
version of u-boot:
- support for LONGHELP so you can get help messages
- auto completion and command editing
- ubi and mii support
- ext2 filesystem (convenient if you have an ext2 from which you want to boot)
- jffs2 and ubifs filesystems (if you want to use these in NAND)
This also makes it more similar to openrd client.
Side effect of this patch is that the code now needs 3 sectors i.s.o. 2
so an existing env is overwritten
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Siddarth Gore [Thu, 18 Mar 2010 14:55:40 +0000 (20:25 +0530)]
Marvell GuruPlug Board Support
GuruPlug Standard: 1 Gb Ethernet, 2 USB 2.0
GuruPlug Plus: 2 Gb Ethernet, 2 USB 2.0, 1 eSATA, 1 uSD slot
References:
http://www.globalscaletechnologies.com/t-guruplugdetails.aspx
http://plugcomputer.org
This patch is for GuruPlug Plus, but it supports Standard version
as well.
Signed-off-by: Siddarth Gore <gores@marvell.com>
Stefano Babic [Sun, 28 Mar 2010 11:43:26 +0000 (13:43 +0200)]
Moved board specific values in config file
The lowlevel_init file contained some hard-coded values
to setup the RAM. These board related values are moved into
the board configuration file.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Wed, 31 Mar 2010 13:32:56 +0000 (06:32 -0700)]
MX51EVK: Remove CPLD related code
There is no CPLD on MX51EVK board, so remove CPLD related function.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Heiko Schocher [Fri, 5 Mar 2010 06:36:33 +0000 (07:36 +0100)]
arm, i.mx27: add support for magnesium board from projectiondesign
This patch adds support for the magnesium board from
projectiondesign. This board uses i.MX27 SoC and has
8MB NOR flash, 128MB NAND flash, FEC ethernet controller
integrated into i.MX27. As this port is based on
the imx27lite port, common config options are collected
in include/configs/imx27lite-common.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Thu, 4 Mar 2010 07:12:05 +0000 (08:12 +0100)]
arm, mx27: add support for SDHC1 pin init
Signed-off-by: Heiko Schocher <hs@denx.de>
Minkyu Kang [Wed, 24 Mar 2010 06:31:06 +0000 (15:31 +0900)]
SAMSUNG: make s5p common gpio functions
Because of s5pc1xx gpio is same as s5p seires SoC,
move gpio functions to drvier/gpio/
and modify structure's name from s5pc1xx_ to s5p_.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Minkyu Kang [Wed, 24 Mar 2010 07:59:30 +0000 (16:59 +0900)]
SAMSUNG: serial: modify name from s5pc1xx to s5p
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Asen Dimov [Wed, 7 Apr 2010 09:33:11 +0000 (12:33 +0300)]
pm9263: remove CONFIG_CMD_AUTOSCRIPT
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Alexander Holler [Mon, 29 Mar 2010 19:39:43 +0000 (21:39 +0200)]
at91: add defines for RTT and GPBR
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Asen Dimov [Tue, 6 Apr 2010 13:17:34 +0000 (16:17 +0300)]
pm9261: remove CONFIG_CMD_AUTOSCRIPT
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Asen Dimov [Tue, 6 Apr 2010 13:18:04 +0000 (16:18 +0300)]
pm9261 converted to at91 soc access
Signed-off-by: Asen Dimov <dimov@ronetix.at>
trix [Sat, 10 Apr 2010 17:46:49 +0000 (12:46 -0500)]
ARM Update mach-types
Fetched from http://www.arm.linux.org.uk/developer/machines/download.php
And built with
repo http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
commit
85b3cce880a19e78286570d5fd004cc3cac06f57
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Minkyu Kang [Fri, 30 Apr 2010 02:10:22 +0000 (11:10 +0900)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Asen Dimov [Mon, 19 Apr 2010 11:18:43 +0000 (14:18 +0300)]
pm9263 converted to at91 soc access
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Asen Dimov [Mon, 19 Apr 2010 11:17:22 +0000 (14:17 +0300)]
at91: define matrix registers bit fields
Signed-off-by: Asen Dimov <dimov@ronetix.at>
Minkyu Kang [Wed, 28 Apr 2010 09:56:39 +0000 (18:56 +0900)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Wolfgang Denk [Tue, 27 Apr 2010 22:10:41 +0000 (00:10 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Wolfgang Denk [Tue, 27 Apr 2010 22:09:53 +0000 (00:09 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc83xx
Stefano Babic [Wed, 21 Apr 2010 07:56:31 +0000 (09:56 +0200)]
MX31: Added LCD support for QONG module
Added support for LCD and splash image to the QONG module.
The supported display is VBEST-VGG322403.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Wolfgang Denk [Tue, 27 Apr 2010 21:02:12 +0000 (23:02 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxx
Wolfgang Denk [Tue, 27 Apr 2010 20:57:41 +0000 (22:57 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Wolfgang Denk [Tue, 27 Apr 2010 20:53:04 +0000 (22:53 +0200)]
Merge branch 'next' of git://git.denx.de/u-boot-nios
Kumar Gala [Tue, 20 Apr 2010 15:02:24 +0000 (10:02 -0500)]
ppc: Split MPC83xx SERDES code from MPC85xx/MPC86xx/QorIQ
The MPC83xx SERDES control is different from the other FSL PPC chips.
For now lets split it out so we can standardize on interfaces for
determining of a device on SERDES is configured.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Lan Chunhe [Wed, 21 Apr 2010 12:40:50 +0000 (07:40 -0500)]
mpc85xx: Add the ability to set LCRR[CLKDIV] to improve R/W speed of flash
Signed-off-by: Lan Chunhe <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Wed, 14 Apr 2010 11:05:06 +0000 (19:05 +0800)]
85xx: clean up the io_sel for PCI express of P1022
clean up the wrong io_sel for PCI express according to latest manual.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Detlev Zundel [Wed, 14 Apr 2010 09:32:20 +0000 (11:32 +0200)]
85xx/socrates: Remove NFS support to fit image size.
This fixes an overflow during the link phase.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Tue, 13 Apr 2010 16:07:57 +0000 (11:07 -0500)]
85xx: Fix compile warning
cpu.c: In function 'checkcpu':
cpu.c:47: warning: unused variable 'gur'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 14 Apr 2010 04:56:23 +0000 (23:56 -0500)]
85xx: Convert cpu_init_f code to use out_be32 for LBC registers
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Mon, 12 Apr 2010 06:23:35 +0000 (14:23 +0800)]
fsl_sata: Move the snoop bit to another place
For P1022 SATA host controller, the data snoop bit of DW3 in PRDT
is moved to bit28.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Mon, 12 Apr 2010 06:23:25 +0000 (14:23 +0800)]
fsl_sata: Add the workaround for errata SATA-A001
After power on, the SATA host controller of P1022 Rev1 is configured
in legacy mode instead of the expected enterprise mode.
Software needs to clear bit[28] of HControl register to change to
enterprise mode after bringing the host offline.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Tue, 8 Dec 2009 03:56:48 +0000 (11:56 +0800)]
fsl-ddr: Add extra cycle to turnaround times
Add an extra cycle turnaround time to read->write to ensure stability
at high DDR frequencies.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Fri, 5 Mar 2010 04:23:00 +0000 (12:23 +0800)]
fsl-ddr: add the macro for Rtt_Nom definition
add the macro definition for Rtt_Nom termination value for DDR3
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 7 Apr 2010 15:39:46 +0000 (10:39 -0500)]
ppc/p4080: Add p4080 DEVDISR2 & SRDS_PLLCR0 defines
Added some needed fines and some misc additional defines
used by p4080 initialization.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Dave Liu [Fri, 5 Mar 2010 04:23:00 +0000 (12:23 +0800)]
ppc/p4080: Extend the GUTS memory map
Extend pin control and clock control to GUTS memory map
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Srikanth Srinivasan [Wed, 10 Feb 2010 09:32:43 +0000 (17:32 +0800)]
ppc/p4080: Fix synchronous frequency calculations
When DDR is in synchronous mode, the existing code assigns sysclk
frequency to DDR frequency. It should be synchronous with the platform
frequency. CPU frequency is based on platform frequency in synchronous
mode.
Also fix:
* Fixes the bit mask for DDR_SYNC (RCWSR5[184])
* Corrects the detection of synchronous mode.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 7 Apr 2010 07:49:12 +0000 (02:49 -0500)]
ppc/85xx: Fixup PCI nodes for P1_P2_RDB
While we had ft_pci_board_setup it wasn't being called by
ft_board_setup. Fix that so we actually update the device tree PCI
nodes on P1_P2_RDB boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Thomas Chou [Wed, 21 Apr 2010 00:40:59 +0000 (08:40 +0800)]
nios2: add nios2-generic board
This is a generic approach to port u-boot for nios2 boards.
You may find the usage of this approach on the nioswiki,
http://nioswiki.com/DasUBoot
A fpga parameter file, which contains base address information
and drivers declaration, is generated from Altera's hardware system
description sopc file using tools.
The example fpga parameter file is compatible with EP1C20, EP1S10
and EP1S40 boards. So these boards can be removed after this commit.
Though epcs controller is removed to cut the dependency of altera_spi
driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Thu, 22 Apr 2010 09:27:16 +0000 (17:27 +0800)]
nios2: fix no flash, add nand and mmc init in board.c
This patch fixes error when CONFIG_SYS_NO_FLASH. And adds
nand flash and mmc initialization, which should go before
env initialization.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Tue, 20 Apr 2010 03:01:11 +0000 (11:01 +0800)]
nios2: consolidate reset initialization
Global interrupt should be disabled from the beginning.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Wed, 31 Mar 2010 00:30:08 +0000 (08:30 +0800)]
altera_jtag_uart: bypass when no jtag connection
This patch adds an option to bypass output waiting when there
is no jtag connection. This allows the jtag uart work similar
to a serial uart, ie, boot even without connection.
This option is enabled with CONFIG_ALTERA_JTAG_UART_BYPASS
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Sat, 17 Apr 2010 15:34:40 +0000 (23:34 +0800)]
nios2: add dma_alloc_coherent
This function return cache-line aligned allocation which is mapped
to uncached io region.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Sat, 17 Apr 2010 15:10:09 +0000 (23:10 +0800)]
nios2: add 64 bits swab support
This patch adds 64 bits swab support. Most 32 bits processors use
this. We need 64 bits swab for UBI.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Wed, 31 Mar 2010 00:36:24 +0000 (08:36 +0800)]
nios2: add altera cf reset
This patch toggles power to reset the cf card.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Thomas Chou [Sat, 17 Apr 2010 09:39:12 +0000 (17:39 +0800)]
nios2: allow link script overriding from boards
This patch allow boards to override the default link script.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:11 +0000 (19:27 +0200)]
mpc5121: pdm360ng: add coprocessor POST
Adds coprocessor communication POST code
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:10 +0000 (19:27 +0200)]
mpc5121: add common post_word_load/store code
Add common post_word_load/post_word_store routines
for all mpc5121 boards. pdm360ng board POST support
added by subsequent patch needs them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:09 +0000 (19:27 +0200)]
mpc5121: add support for PDM360NG board
PDM360NG is a MPC5121E based board by ifm ecomatic gmbh.
Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:08 +0000 (19:27 +0200)]
mpc5121: determine RAM size using get_ram_size()
Configure CONFIG_SYS_MAX_RAM_SIZE address range in
DDR Local Access Window and determine the RAM size.
Fix DDR LAW afterwards using detected RAM size.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:07 +0000 (19:27 +0200)]
mpc512x: make MEM IO Control configuration a board config option
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:06 +0000 (19:27 +0200)]
mpc5121: add PSC serial communication routines
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:05 +0000 (19:27 +0200)]
mpc512x: add multi serial PSC support
Extend mpc512x serial driver to support multiple PSC ports.
Subsequent patches for PDM360NG board support make use of this
functionality by defining CONFIG_SERIAL_MULTI in the board config
file. Additionally the used PSC devices are specified by defining
e.g. CONFIG_SYS_PSC1, CONFIG_SYS_PSC4 and CONFIG_SYS_PSC6.
Support for PSC devices other than 1, 3, 4 and 6 is not added
by this patch because these aren't used currently. In the future
it can be easily added using DECLARE_PSC_SERIAL_FUNCTIONS(N) and
INIT_PSC_SERIAL_STRUCTURE(N) macros in cpu/mpc512x/serial.c.
Additionally you have to add code for registering added
devices in serial_initialize() in common/serial.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Anatolij Gustschin [Sat, 24 Apr 2010 17:27:04 +0000 (19:27 +0200)]
serial: struct serial_device: add uninit() entry for drivers
Subsequent patch extends mpc512x serial driver to support
multiple PSC ports. The driver will provide an uninit()
function to stop the serial controller and to disable the
controller's clock. Adding uninit() entry to struct serial_device
allows disabling the serial controller after usage of
a stdio serial device.
This patch adds uninit() entry to the struct serial_device
and fixes initialization of this structure in the code
accordingly.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Wolfgang Denk [Sat, 24 Apr 2010 19:25:42 +0000 (21:25 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
Wolfgang Denk [Sat, 24 Apr 2010 19:16:57 +0000 (21:16 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-ppc4xx
Wolfgang Denk [Sat, 24 Apr 2010 19:13:31 +0000 (21:13 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-microblaze
Wolfgang Denk [Sat, 24 Apr 2010 19:11:56 +0000 (21:11 +0200)]
Merge branch 'master' of git://git.denx.de/u-boot-i2c
Stefano Babic [Tue, 13 Apr 2010 10:19:06 +0000 (12:19 +0200)]
MX31: Removed erroneous board name from QONG
QONG is a module that can be installed on several boards,
not only on the QONG-EVB manufactured by Dave srl.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Thu, 8 Apr 2010 15:23:52 +0000 (17:23 +0200)]
MX31: Add UBI support to QONG module
The UBI/UBIFS support is added to the QONG module.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Wed, 31 Mar 2010 08:27:47 +0000 (10:27 +0200)]
MX31: Support 128MB RAM on QONG module
The QONG module can be downsized and delivered
with 128MB instead of 256MB. The patch adds
run time support for the two different memory
configurations.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 29 Mar 2010 14:43:39 +0000 (16:43 +0200)]
MX31: Add support for NAND to QONG board
The NAND device is connected to the FPGA of the QONG board
and not to the NFC controller. For this reason, the FPGA must
be set and initialized before accessing to the NAND itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Mon, 29 Mar 2010 13:56:10 +0000 (15:56 +0200)]
MX31: add pin definitions for NAND controller
Add pin definitions ralted to the NAND controller to be used
to set up the pin multiplexer.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Tue, 13 Apr 2010 10:07:00 +0000 (12:07 +0200)]
MX31: add accessor function to get a gpio
The patch adds an accessor function to get the value of a gpio.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Tue, 13 Apr 2010 10:38:43 +0000 (12:38 +0200)]
mx51evk: correct list of possible BOOT_FROM values
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stefano Babic [Tue, 13 Apr 2010 10:38:22 +0000 (12:38 +0200)]
mkimage: correct spelling error in imximage
Signed-off-by: Stefano Babic <sbabic@denx.de>
John Rigby [Thu, 8 Apr 2010 05:30:09 +0000 (23:30 -0600)]
MX25 print arm clock instead of mpllclk on boot
Replace call to imx_get_mpllclk with imx_get_armclk
to show frequency of ARM core instead of mpll internal
bus in print_cpuinfo.
Signed-off-by: John Rigby <jcrigby@gmail.com>
CC: Stefano Babic <sbabic@denx.de>
Dipen Dudhat [Mon, 5 Oct 2009 10:11:58 +0000 (15:41 +0530)]
ppc/85xx: PIO Support for FSL eSDHC Controller Driver
On some Freescale SoC Internal DMA of eSDHC controller has bug.
So PIO Mode has been introduced to do data transfer using CPU.
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Kim Phillips [Wed, 21 Apr 2010 00:37:54 +0000 (19:37 -0500)]
mpc83xx: turn on icache in core initialization to improve u-boot boot time
before, MPC8349ITX boots u-boot in 4.3sec:
column1 is elapsed time since first message
column2 is elapsed time since previous message
column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA: Configured for compact flash
0.032 0.000: I2C: ready
0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI: Bus Dev VenId DevId Class Int
2.652 0.011: 00 10 1095 3114 0180 00
2.652 0.000: PCI: Bus Dev VenId DevId Class Int
2.652 0.000: In: serial
2.652 0.000: Out: serial
2.652 0.000: Err: serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net: TSEC1: No support for PHY id
ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE: Bus 0: .** Timeout **
after, MPC8349ITX boots u-boot in 3.0sec:
0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA: Configured for compact flash
0.038 0.000: I2C: ready
0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI: Bus Dev VenId DevId Class Int
1.390 0.000: 00 10 1095 3114 0180 00
1.390 0.000: PCI: Bus Dev VenId DevId Class Int
1.400 0.010: In: serial
1.400 0.000: Out: serial
1.400 0.000: Err: serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net: TSEC1: No support for PHY id
ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE: Bus 0: .** Timeout **
also tested on these boards (albeit with a less accurate
boottime measurement method):
seconds: before after
8349MDS ~2.6 ~2.2
8360MDS ~2.8 ~2.6
8313RDB ~2.5 ~2.3 #nand boot
837xRDB ~3.1 ~2.3
also tested on an 8323ERDB.
v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Thu, 15 Apr 2010 22:36:05 +0000 (17:36 -0500)]
mpc83xx: enable command line autocompletion
because it's convenient.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Kim Phillips [Thu, 15 Apr 2010 22:36:02 +0000 (17:36 -0500)]
mpc83xx: use "A" nomenclature only on mpc834x and mpc836x families
marketing didn't extend their postpend-with-an-A naming strategy
on rev.2's and higher beyond the first two 83xx families. This
patch stops us from misreporting we're running e.g., on an MPC8313EA,
when such a name doesn't exist.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Rini van Zetten [Thu, 15 Apr 2010 14:03:05 +0000 (16:03 +0200)]
mpc83xx: Use CONFIG_FSL_ESDHC to enable sdhc clk
Enable eSDHC Clock based on generic CONFIG_FSL_ESDHC define
instead of a platform define. This will enable all the 83xx
platforms to use sdhc_clk based on CONFIG_FSL_ESDHC. It's
the same patch as commit
6b9ea08c5010eab5ad1056bc9bf033afb672d9cc
for the ppc/85xx.
Signed-off-by: Rini <rini@arvoo.nl>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Minkyu Kang [Thu, 22 Apr 2010 03:39:56 +0000 (12:39 +0900)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Stefan Roese [Thu, 15 Apr 2010 14:07:28 +0000 (16:07 +0200)]
Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
Frans Meulenbroeks [Tue, 6 Apr 2010 13:36:11 +0000 (19:06 +0530)]
configs/openrd_base.h: reordered macros
moved CONFIG_CMD_FAT to filesystem section
swapped CONFIG_CMD_NAND and CONFIG_CMD_MII so they are alpha correct
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Frans Meulenbroeks [Tue, 6 Apr 2010 12:56:19 +0000 (18:26 +0530)]
configs/sheevaplug: added a few additional commands
This patch includes a few additional commands in the sheevaplug
version of u-boot:
- support for LONGHELP so you can get help messages
- auto completion and command editing
- ubi and mii support
- ext2 filesystem (convenient if you have an ext2 from which you want to boot)
- jffs2 and ubifs filesystems (if you want to use these in NAND)
This also makes it more similar to openrd client.
Side effect of this patch is that the code now needs 3 sectors i.s.o. 2
so an existing env is overwritten
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
projects / platform / kernel / u-boot.git / log