Tom Rini [Tue, 10 Mar 2020 11:51:56 +0000 (07:51 -0400)]
Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-net
Clemens Gruber [Mon, 24 Feb 2020 19:52:20 +0000 (20:52 +0100)]
net: phy: marvell: Unify 88E151x series phy_driver
The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit
83cfbeb0df9f ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Heinrich Schuchardt [Sat, 22 Feb 2020 07:43:40 +0000 (08:43 +0100)]
net: tftp: use correct printf codes
When printing unsigned numbers use %u.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek [Tue, 18 Feb 2020 12:51:02 +0000 (13:51 +0100)]
net: phy: dp83867: Add SGMII mode type switching
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit
a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit
507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek [Mon, 17 Feb 2020 09:38:57 +0000 (10:38 +0100)]
dt-bindings: net: dp83867: Remove binding doc from U-Boot tree
U-Boot is having DT which doesn't cover all options currently supported by
driver. DT binding is aligned with Linux kernel version available here.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ti,dp83867.txt
Based on my talk with Grygorii Strashko better will be to remove it.
Also Linux kernel bindings are being converted to yaml that's another
reason to do it only at one place.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Alex Marginean [Thu, 9 Jan 2020 08:50:05 +0000 (10:50 +0200)]
net: phy: add XFI, USXGMII types to is_10g_interface() helper
The helper is used to reset PHYs on connect and it determines the clause
to use (C22/C45) based on interface type. This fixes 'PHY reset timed out'
warnings in console for USXGMII/XFI PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Fri, 3 Jan 2020 22:08:47 +0000 (22:08 +0000)]
net: phy: Fix overlong PHY timeout
Commit
27c3f70f3b50 ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: net: phy: Increase link up delay in genphy_update_link() ("
27c3f70f3b50")
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Mon, 25 Nov 2019 01:32:15 +0000 (01:32 +0000)]
doc: net: Rewrite network driver documentation
doc/README.drivers.eth seems like a good source for understanding
U-Boot's network subsystem, but is only talking about legacy network
drivers. This is particularly sad as proper documentation would help in
porting drivers over to the driver model.
Rewrite the document to describe network drivers in the new driver model
world. Most driver callbacks/methods are almost identical in their
semantic, but recv() differs in some important details.
Also keep some parts of the original text at the end, to help
understanding old drivers. Add some hints on how to port drivers over.
This also uses the opportunity to reformat the document in reST, on the
way moving it into doc/driver-model and adding it into the structure
there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Wed, 4 Dec 2019 13:32:16 +0000 (15:32 +0200)]
drivers: net: phy: aquantia: make it less verbose
The driver now unconditionally prints some information that's not
universally useful. Replace printf with debug.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Wed, 4 Dec 2019 13:32:15 +0000 (15:32 +0200)]
drivers: net: phy: aquantia: drop XGMII as a valid system interface proto
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Pankit Garg [Tue, 19 Nov 2019 09:49:31 +0000 (09:49 +0000)]
env: Update env_addr for mmc environment driver
Make sure the gd struct is up-to-date.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Samuel Mendoza-Jonas [Tue, 18 Jun 2019 01:37:18 +0000 (11:37 +1000)]
phy: Include NC-SI in phy setup
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Samuel Mendoza-Jonas [Tue, 18 Jun 2019 01:37:17 +0000 (11:37 +1000)]
phy: Add support for the NC-SI protocol
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Mon, 9 Mar 2020 17:01:57 +0000 (13:01 -0400)]
Azure/Travis: Re-sync jobs and clarify exclusions
We keep both of these jobs in sync as much as possible even when the
primary motivation is to keep Travis from exceeding the build time limit
there. With that in mind:
- Use "rk" not "rockchip" to get all Rockchip SoC platforms in one job,
rather than just all Rockchip vendor platforms.
- The NXP LX216* SoCs have their own job, exclude them from the AArch64
generic job.
- SoCFPGA SoCs have their own job, exclude them from the AArch64 generic
job.
Signed-off-by: Tom Rini <trini@konsulko.com>
Samuel Mescoff [Mon, 15 Apr 2019 10:28:26 +0000 (12:28 +0200)]
Makefile: fix processing of default environment file
Allow the default environment file to contain long lines split into
multiples lines.
Leading white spaces can be added for readability as well.
Signed-off-by: Samuel Mescoff <samuel@mescoff.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Thu, 5 Mar 2020 12:51:12 +0000 (07:51 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Revert "x86: use invd instead of wbinvd in real mode start code"
- Convert toradex boards README to reST
- serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()
- x86: apl: Use cpu_x86_get_count() for cpu_ops.get_count
Wolfgang Wallner [Tue, 25 Feb 2020 12:19:48 +0000 (13:19 +0100)]
x86: apl: Use cpu_x86_get_count() for cpu_ops.get_count
Use cpu_x86_get_count() to read the number of cores.
cpu_x86_get_count() reads the number of CPUs from the device tree.
Using this function we can support multiple Apollo Lake
variants, e.g.: E3940 (4 cores) and E3930 (2 cores).
This was tested on the E3940 and E3930 Apollo Lake variants.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Tue, 25 Feb 2020 12:19:47 +0000 (13:19 +0100)]
x86: cpu_x86: Make cpu_x86_get_count() non-static
The function cpu_x86_get_count() is also useful for other modules.
Make it non-static and add a prototype + description.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Fri, 21 Feb 2020 11:20:09 +0000 (12:20 +0100)]
doc: Chromebook Coral: Fix typo for "Top of CAR region"
The value for "Top of CAR region" should be
fefc0000, not
fefc000. This matches the Kconfig default values, as
SYS_CAR_ADDR and SYS_CAR_SIZE are 0xfef00000 and 0xc0000
respectively.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Tue, 18 Feb 2020 14:32:10 +0000 (15:32 +0100)]
x86: p2sb: Drop 'apl' prefix
Drop the Apollo Lake prefix 'apl' from the functions, types and
variables in the P2SB driver.
The P2SB is not Apollo Lake specific, and as such it was moved in
commit
2999846c1127 ("x86: Move P2SB from Apollo Lake to a more generic
location") from the Apollo Lake folder to the intel_common folder.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wolfgang Wallner [Mon, 2 Mar 2020 13:41:14 +0000 (14:41 +0100)]
serial: ns16550: Move PCI access from ofdata_to_platdata() to probe()
Currently the ofdata_to_platdata() method calls dev_read_addr_pci(),
which potentially accesses the parent PCI bus. If this happens before
the parent PCI bus is probed the resulting address will be wrong.
This behavior was triggered by commit
82de42fa1468 ("dm: core:
Allocate parent data separate from probing parent").
According to a comment in drivers/pci/pci-uclass.c [1] accessing
the PCI parent bus in ofdata_to_platdata() is not allowed, and the
access should be moved to the probe() function.
Move the call to dev_read_addr_pci() and the related handling of the
'addr' value from the ofdata_to_platdata() to its own function,
which is then called from the probe() method.
While moving the code, the comment /* try Processor Local Bus device
first */ was dropped. It was initially added with commit
3db886a5bf38
("serial: ns16550: Support ns16550 compatible pci uart devices") and
later made obsolete with commit
33c215af4b9d ("dm: pci: Add a function
to read a PCI BAR").
[1] Comment in drivers/pci/pci-uclass.c:
"A common cause of this problem is that this function is called in the
ofdata_to_platdata() method of @dev. Accessing the PCI bus in that
method is not allowed, since it has not yet been probed. To fix this,
move that access to the probe() method of @dev instead."
Fixes:
82de42fa1468 ("dm: core: Allocate parent data separate from probing parent")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # Tested on Intel Galileo
Andy Shevchenko [Mon, 17 Feb 2020 15:30:12 +0000 (17:30 +0200)]
Revert "x86: use invd instead of wbinvd in real mode start code"
This reverts commit
0d67fac29f3187e67f4fd3ef15f73e91be2fad12.
As real hardware testing (*) shows the above mentioned commit
breaks U-Boot on it. Revert for the upcoming release. We may get
more information in the future and optimize the code accordingly.
(*) on Intel Edison board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix a typo in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Sat, 15 Feb 2020 20:22:00 +0000 (21:22 +0100)]
x86: remove dead code in intel_clk_get_rate()
If all branches of a switch statement have a return instruction, all
subsequent lines are unreachable.
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:32 +0000 (17:14 +0200)]
toradex: MAINTAINERS: entries for new reST docs
Add entries for the newly created documentation files in reST
format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:31 +0000 (17:14 +0200)]
doc: board: colibri-imx8x: convert readme to reST
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:30 +0000 (17:14 +0200)]
doc: board: apalis-imx8: convert readme to reST
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:29 +0000 (17:14 +0200)]
doc: board: verdin-imx8mm: convert readme to reST
Convert README to reStructuredText format.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: spell out U-Boot correctly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Igor Opaniuk [Wed, 12 Feb 2020 15:14:28 +0000 (17:14 +0200)]
doc: board: toradex: add colibri_imx7.rst
- add initial index for toradex boards reST documentation
- add initial colibri_imx7.rst doc file which provides all needed
information for obtaining a workable image ready for flashing
for both eMMC/NAND versions of Colibri iMX7.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: make title underline the same length as the title itself]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 2 Feb 2020 20:37:06 +0000 (13:37 -0700)]
x86: Correct error return value in mrccache_get_region()
This function doesn't use uclass_find_first_device() correctly. Add a
check that the device is found so we don't try to read properties from a
NULL device.
The fixes booting on minnoxmax.
Fixes:
87f1084a630 ("x86: Adjust mrccache_get_region() to use livetree")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Thu, 5 Mar 2020 00:21:00 +0000 (19:21 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-sh
- Limit bootloader size to 1 MiB on R-Car Gen3
Tom Rini [Wed, 4 Mar 2020 15:41:41 +0000 (10:41 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
- ABB SECU board
- Assorted minor fixes
Tom Rini [Wed, 4 Mar 2020 15:41:27 +0000 (10:41 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
- DFU / Thor fixes
Tom Rini [Wed, 4 Mar 2020 02:48:49 +0000 (21:48 -0500)]
Merge tag 'dm-pull-3mar20' of git://git.denx.de/u-boot-dm
Fixes for power domain on device removal
Holger Brunck [Wed, 19 Feb 2020 18:55:14 +0000 (19:55 +0100)]
ARM: socfpga: Add initial support for the ABB SECU board
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Anatolij Gustschin [Mon, 17 Feb 2020 11:36:44 +0000 (12:36 +0100)]
video: meson: keep power domain up after booting
Add driver flag to skip power domain disabling on device removal.
Fixes:
52edfed65de9 ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Anatolij Gustschin [Mon, 17 Feb 2020 11:36:43 +0000 (12:36 +0100)]
dm: core: Add a flag for power domain control on device removal
In various cases a power domain must stay enabled after device
removal when booting OS (i.e. serial debug console or display).
Add a flag to selectively skip switching off a power domain.
Fixes:
52edfed65de9 ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Mon, 2 Mar 2020 14:20:30 +0000 (09:20 -0500)]
Merge tag 'u-boot-stm32-
20200203' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- convert stm32mp1 board documentation to rst format
Tom Rini [Mon, 2 Mar 2020 14:20:12 +0000 (09:20 -0500)]
Merge tag 'xilinx-for-v2020.04-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx fixes for v2020.04-rc4
- Fix link good bit handling in dp83867
- Rename generic Zynq defconfig
- Fix zybo z7 low leve setup
- Fix error path in zynq_gem driver and fix 64bit usage
- Fix invalid clock name quieries for Versal
- Fix zynq/zynqmp SPL low level configuration via DT selection
Patrick Delaunay [Tue, 25 Feb 2020 18:04:14 +0000 (19:04 +0100)]
doc: add board documentation for stm32mp1
Change plain test README to rst format and move this file
in documentation directory.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Heinrich Schuchardt [Sun, 16 Feb 2020 09:11:18 +0000 (10:11 +0100)]
stm32mp1: rng: remove superfluous assignment
We should not assign a value that is overwritten before use.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Marek Vasut [Sat, 15 Feb 2020 13:10:09 +0000 (14:10 +0100)]
ARM: socfpga: Add missing Denali NAND config options
The Denali SPL shim won't build without these options set,
set them accordingly to fix the build error and let the SPL
shim to work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Marek Vasut [Sat, 15 Feb 2020 13:10:02 +0000 (14:10 +0100)]
ARM: socfpga: Permit overriding the default timer frequency
The default timer rate may be different than 25 MHz, permit overriding
the default rate in board configuration file. Ultimatelly, this should
be properly handled by a clock driver, however that is not available
on Gen5 yet.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Marek Vasut [Sat, 15 Feb 2020 13:46:10 +0000 (14:46 +0100)]
rtc: m41t62: add compatible for m41st87
This adds a compatible string for m41st87. This ensures that this driver
can be used for m41st87.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Seung-Woo Kim [Thu, 13 Feb 2020 08:24:11 +0000 (17:24 +0900)]
gadget: f_thor: add missing line breaks for pr_err()
After the commit
9b643e312d52 ("treewide: replace with error()
with pr_err()"), there are pr_err() usages without line break. Add
missing line breaks for pr_err() used in f_thor.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Andy Shevchenko [Wed, 29 Jan 2020 15:23:14 +0000 (17:23 +0200)]
dfu: Reset timeout in case of DFU request
In case dfu command is being executed with timeout option,
the timer may expire in the middle of DFU operation. If there
is DFU request coming, we may simple reset timeout value
to prevent aborting of ongoing DFU operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Marek Vasut [Fri, 24 Jan 2020 00:31:37 +0000 (01:31 +0100)]
ARM: rmobile: Limit bootloader size to 1 MiB on R-Car Gen3
The HF/QSPI flash layout permits up to 1 MiB large bootloader blob,
set CONFIG_BOARD_SIZE_LIMIT to enforce this limit and set the
monitor size to match accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Sat, 29 Feb 2020 13:01:07 +0000 (08:01 -0500)]
Merge tag 'efi-2020-04-rc4-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (2)
In Linux next-
20200228 patches have been merged to load an initial ramdisk
using an EFI_LOAD_FILE2_PROTOCOL provided by the firmware. See commit
ec93fc371f01 ("efi/libstub: Add support for loading the initrd from a
device path"). The idea behind it is that the firmware should be
responsible for validating the initrd in a secure boot setup.
This pull-request comprises a patch series which let's U-Boot provide an
initial implementation of the EFI_LOAD_FILE2_PROTOCOL providing the initrd.
Tom Rini [Sat, 29 Feb 2020 13:00:53 +0000 (08:00 -0500)]
Merge tag 'uniphier-v2020.04-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
Masahiro Yamada [Fri, 28 Feb 2020 12:57:21 +0000 (21:57 +0900)]
ARM: dts: uniphier: remove U-Boot own EEPROM compatible and property
The compatible string "i2c-eeprom" is U-Boot own compatible, which
has never been approved by the DT community. "u-boot,i2c-offset-len"
is also a U-Boot own hack.
Linux adds "atmel,*" as generic compatibles, and U-Boot also followed
it by commit
d7e28918aa3f ("i2c_eeprom: Add reading support").
The U-Boot own hack is no longer needed. Just sync with Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 28 Feb 2020 12:57:20 +0000 (21:57 +0900)]
ARM: dts: uniphier: add reset-names to NAND controller node
Import Linux commits:
37f3e0096f71 ("ARM: dts: uniphier: add reset-names to NAND controller node")
e98d5023fe1f ("arm64: dts: uniphier: add reset-names to NAND controller node")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 28 Feb 2020 12:57:19 +0000 (21:57 +0900)]
ARM: dts: uniphier: rename DT nodes to follow json-schema
Import the nodename changes I made in Linux for avoiding dt-schama
warnings. This follows the $nodename patterns in the dt-schema.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Heinrich Schuchardt [Sat, 22 Feb 2020 06:47:20 +0000 (07:47 +0100)]
doc/efi: add load file 2 protocol to HTML documentation
The load file 2 protocol can be used by the Linux kernel to load the initial
RAM disk. U-Boot can be configured to provide an implementation.
Add a description to the UEFI overview and document the related functions
in the API section.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Fri, 21 Feb 2020 07:55:46 +0000 (09:55 +0200)]
efi_selftest: add selftests for loadfile2 used to load initramfs
Provide a unit test loading an initial ramdisk using the
EFI_LOAD_FILE2_PROTOCOL. The test is only executed on request.
An example usage - given a file image with a file system in partition 1
holding file initrd - is:
* Configure the sandbox with
CONFIG_EFI_SELFTEST=y
CONFIG_EFI_LOAD_FILE2_INITRD=y
CONFIG_EFI_INITRD_FILESPEC="host 0:1 initrd"
* Run ./u-boot and execute
host bind 0 image
setenv efi_selftest load initrd
bootefi selftest
This would provide a test output like:
Testing EFI API implementation
Selected test: 'load initrd'
Setting up 'load initrd'
Setting up 'load initrd' succeeded
Executing 'load initrd'
Loaded
12378613 bytes
CRC32
2997478465
Executing 'load initrd' succeeded
Now the size and CRC32 can be compared to the provided file.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Ilias Apalodimas [Fri, 21 Feb 2020 07:55:45 +0000 (09:55 +0200)]
efi_loader: Implement FileLoad2 for initramfs loading
Following kernel's proposal for an arch-agnostic initrd loading
mechanism [1] let's implement the U-boot counterpart.
This new approach has a number of advantages compared to what we did up
to now. The file is loaded into memory only when requested limiting the
area of TOCTOU attacks. Users will be allowed to place the initramfs
file on any u-boot accessible partition instead of just the ESP one.
Finally this is an attempt of a generic interface across architectures
in the linux kernel so it makes sense to support that.
The file location is intentionally only supported as a config option
argument(CONFIG_EFI_INITRD_FILESPEC), in an effort to enhance security.
Although U-boot is not responsible for verifying the integrity of the
initramfs, we can enhance the offered security by only accepting a
built-in option, which will be naturally verified by UEFI Secure Boot.
This can easily change in the future if needed and configure that via ENV
or UEFI variable.
[1] https://lore.kernel.org/linux-efi/
20200207202637.GA3464906@rani.riverdale.lan/T/#m4a25eb33112fab7a22faa0fd65d4d663209af32f
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Fri, 28 Feb 2020 18:28:38 +0000 (13:28 -0500)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 28 Feb 2020 16:04:50 +0000 (11:04 -0500)]
Merge branch '2020-02-28-mpc8xx-fixes'
- Fix the watchdog on mpc8xx platforms
Christophe Leroy [Wed, 26 Feb 2020 16:17:52 +0000 (16:17 +0000)]
watchdog: Don't select CONFIG_WATCHDOG and CONFIG_HW_WATCHDOG at the same time
Commit
06985289d452 ("watchdog: Implement generic watchdog_reset()
version") introduced an automatic selection of CONFIG_WATCHDOG by
CONFIG_WDT. But for boards selecting CONFIG_HW_WATCHDOG, like
boards have a powerpc 8xx, CONFIG_WATCHDOG shall not be selected
as they are mutually exclusive.
Make CONFIG_WATCHDOG dependent on !CONFIG_HW_WATCHDOG
Fixes:
06985289d452 ("watchdog: Implement generic watchdog_reset() version")
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
Christophe Leroy [Thu, 20 Feb 2020 07:39:51 +0000 (07:39 +0000)]
watchdog: mpc8xx: Revert the 8xx watchdog back to CONFIG_HW_WATCHDOG
Commit
f3729ba6e7b2 ("watchdog: mpc8xx_wdt: Watchdog driver and macros
cleanup") switched the watchdog to CONFIG_WATCHDOG. But this is not
compatible with the 8xx because it starts the watchdog HW timer at
reset and must be serviced from the very beginning including while
U-boot is executed in the firmware before relocation in RAM.
Select CONFIG_HW_WATCHDOG and make hw_watchdog_reset() visible.
Meanwhile, finalise the cleanup of arch/powerpc/cpu/mpc8xx/Kconfig by
removing the lines put in comment in that commit, and also remove
again the selection of CONFIG_MPC8xx_WATCHDOG which was removed by
that commit and brought back by mistake by commit
b3134ffbd944
("watchdog: Kconfig: Sort entry alphabetically")
Note that there was an 'imply WATCHDOG' in the original commit but
it disappeared in the Kconfig alphabetical sorting, so no need to
remove it here.
Fixes:
f3729ba6e7b2 ("watchdog: mpc8xx_wdt: Watchdog driver and macros cleanup")
Fixes:
b3134ffbd944 ("watchdog: Kconfig: Sort entry alphabetically")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Michal Simek [Tue, 25 Feb 2020 14:27:09 +0000 (15:27 +0100)]
ARM: zynq: Remove single comment about QSPI
Very likely configs have been moved to Kconfig by scripts and this just
remains there that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 13 Feb 2020 13:59:40 +0000 (14:59 +0100)]
ARM: zynq: Rename defconfig to be align with ZynqMP and Versal
Just cosmetic change before real switch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 13 Feb 2020 13:36:34 +0000 (14:36 +0100)]
arm: xilinx: Fill DEVICE_TREE directly in Makefiles
DEVICE_TREE variable is not exported from dts/Makefile that's why it is
necessary to setup directly before use.
Fixes:
312f2c5b14fa ("arm: xilinx: Use device tree which can be passed on cmd line")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 6 Feb 2020 13:36:46 +0000 (14:36 +0100)]
net: zynq: Free allocated buffers in case of error
Driver probe function is called again and again in case of error.
Malloc space is getting full which is is reported by:
Insufficient RAM for page table: 0x15000 > 0x14000.
Please increase the size in get_page_table_size()
### ERROR ### Please RESET the board ###
The patch is freeing allocated buffers on error path to avoid panic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Thu, 6 Feb 2020 14:59:23 +0000 (15:59 +0100)]
net: phy: dp83867: Clean force link good bit
On Xilinx ZynqMP revA board initial value of PHYCR register is 0x5448 which
means FORCE_LINK_GOOD is already setup. Origin code was doing write but the
new code is doing read/modify/write and keep this bit untouched. That's why
ethernet stop to work.
The patch is cleaning this bit when PHYCR value is composed.
Tested on Xilinx zcu102-revA and zcu104-rev1.0 boards.
Fixes:
37d6265f2bfa ("net: phy: dp83867: refactor rgmii configuration")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
T Karthik Reddy [Mon, 20 Jan 2020 06:59:23 +0000 (23:59 -0700)]
mtd: nand: Fix on-die ecc issues in arasan_nfc driver
Fixed wrong enumeration of nand_config structure. Added chip select
function before reading the nand chip for maf/dev id's, without this
unable to access id's from some of the micron chips. Also added a
print statement to identify if a nand flash is using on-die ecc.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Rajan Vaja [Thu, 16 Jan 2020 11:55:05 +0000 (03:55 -0800)]
versal: drivers: clk: Fix invalid clock name queries
The clock driver makes EEMI call to get the name of invalid clk
when executing versal_get_clock_info() function. This results in
error messages.
Added check for validating clock before saving clock attribute and
calling versal_pm_clock_get_name() in versal_get_clock_info() function.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Milan Obuch [Mon, 20 Jan 2020 01:32:19 +0000 (22:32 -0300)]
arm: zynq: zybo z7: fix SPL uart init bitrate
The board uses 100 MHz clock for UART bitrate generator,
but is configured as 50 MHz on defconfig.
This produces wrong console output.
The first message, "Debug uart enabled" is received as:
"������b"
Fix the issue by configuring the correct clock for the
UART baudrate generator
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Milan Obuch [Mon, 20 Jan 2020 01:33:30 +0000 (22:33 -0300)]
arm: zynq: zybo z7: fix MIO init issue
The board has two push button connected to MIO pins
50 and 51, which have a pull-down resistor and are
connected to 1.8V when pressed.
These two pins are wrongly initialized with internal
pull-up enabled so they are reported as 1 all the time
with no change when pressed.
Disable the internal pull-up to fix the issue.
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
T Karthik Reddy [Wed, 15 Jan 2020 09:15:13 +0000 (02:15 -0700)]
net: zynq_gem: Use ulong instead of u32 data type
flush_dcache_range() expects unsigned long in the arguments. Here u32
variable is unable to hold the higher address value when ddr mapped
to higher addresses & flushing lower address dchache range instead
which is unmapped causing to crash.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Masahiro Yamada [Thu, 27 Feb 2020 11:31:18 +0000 (20:31 +0900)]
ARM: uniphier: enable CONFIG_MMC_HS400_SUPPORT for uniphier_v8_defconfig
The eMMC controller on LD20 or later supports HS-400 mode. It works on
a quick test. Enable it in case somebody may want to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 14 Feb 2020 11:54:42 +0000 (20:54 +0900)]
ARM: uniphier: detect the base of micro support card at run-time
The base address 0x43f00000 is no longer true for the future SoC.
Extract the base address from the device tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 14 Feb 2020 11:54:41 +0000 (20:54 +0900)]
ARM: uniphier: remove workaround for the NAND write protect
This workaround was previously needed for LD4, Pro4, sLD8, Pro5
SoCs. The boot ROM does not touch this register for PXs2/LD6b or
later.
Now that the reset signal of the Denali NAND controller is always
asserted in board_init() then deasserted in the driver, the
WRITE_PROTECT register gets back to the default value, which means
the write protect is deasserted.
This workaround can go away entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 14 Feb 2020 11:54:40 +0000 (20:54 +0900)]
ARM: uniphier: move NAND reset assertion to U-Boot proper from SPL
The comment /* deassert reset */ is wrong. It asserts the reset.
It no longer needs to stay in SPL. The NAND controller reset is
handled in the driver. So, this assert can be moved to the
board_init() of U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 13 Feb 2020 03:27:37 +0000 (12:27 +0900)]
ARM: uniphier: add sdscript, sdboot, sdupdate environment variables
Add handy macros:
- sdscript: source boot.scr in the file system of the SD media
- sdboot : boot the kernel using the images in the file system
of the SD media
- sdscript: update the boot firmware in the SD media
(in raw block sectors)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Tue, 4 Feb 2020 11:13:43 +0000 (20:13 +0900)]
ARM: uniphier: enable CONFIG_MMC_SDHCI_ADMA for uniphier_v8_defconfig
Switch over to ADMA from SDMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Thu, 27 Feb 2020 13:51:01 +0000 (08:51 -0500)]
Merge tag 'ti-v2020.04-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-ti
- Minor fix in AVS class 0 driver
- DHCP fixes in Keystone2 HS platforms.
Tom Rini [Wed, 26 Feb 2020 19:49:24 +0000 (14:49 -0500)]
Merge tag 'efi-2020-04-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4
UEFI spec 2.8 errata A replaces the RuntimeServicesSupported variable
defined in UEFI spec 2.8 by the configuration table
EFI_RT_PROPERTIES_TABLE. So let's follow suit.
Heinrich Schuchardt [Wed, 19 Feb 2020 19:48:49 +0000 (20:48 +0100)]
efi_loader: implement EFI_RT_PROPERTIES_TABLE
UEFI spec 2.8 errata A replaces the RuntimeServicesSupported variable
defined in UEFI spec 2.8 by the configuration table
EFI_RT_PROPERTIES_TABLE. So let's follow suit.
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Madan Srinivas [Fri, 14 Feb 2020 14:05:24 +0000 (09:05 -0500)]
defconfig: k2x_hs: Remove DTB_RESELECT to fix DHCP issue
This fixes the inadvertent definition of CONFIG_DTB_RESELECT and
CONFIG_MULTI_DTB_FIT in the K2x HS defconfigs, that happened as part of
a resync of the defconfigs.
The inclusion of these config options causes ethernet to stop working on
K2x HS devices as they interfere with the installation of the secure
boot monitor.
This patch also removes the above configs for the K2 GP devices, as they
are not needed, and to keep the differences between the GP and HS
defconfigs to a minimum.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Vignesh Raghavendra [Fri, 14 Feb 2020 12:22:17 +0000 (17:52 +0530)]
misc: k3_avs: Fix possible NULL pointer deference
Its possible that k3_avs_priv is NULL because the driver may not have
been probed yet. Therefore check if pointer is valid before
dereferencing it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tom Rini [Wed, 26 Feb 2020 12:53:20 +0000 (07:53 -0500)]
Prepare v2020.04-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 26 Feb 2020 04:35:53 +0000 (23:35 -0500)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx
- Update Sata node for T2080QDS and revert SATA related unrequired
patches.
Tom Rini [Tue, 25 Feb 2020 18:59:21 +0000 (13:59 -0500)]
Merge branch '2020-02-25-master-imports'
- Assorted fixes
Carl Gelfand [Wed, 22 Jan 2020 21:03:02 +0000 (16:03 -0500)]
board: novtech: meerkat96: use correct mmc driver
When the board was originally submitted, it was attempting to use the
ESDHC driver. The board uses the USDHC driver.
Signed-off-by: Carl Gelfand <carl@novtech.com>
Cc: Shawn Guo <shawn.guo@kernel.org> (maintainer:MEERKAT96 BOARD)
Acked-by: Shawn Guo <shawnguo@kernel.org>
Markus Klotzbuecher [Wed, 12 Feb 2020 19:46:45 +0000 (20:46 +0100)]
moveconfig: convert ps.stderr to string
Printing the error message in verbose mode fails, since python3
doesn't implicitely convert bytes to strings.
Signed-off-by: Markus Klotzbuecher <mk@mkio.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Markus Klotzbuecher [Wed, 12 Feb 2020 19:46:44 +0000 (20:46 +0100)]
moveconfig: replace unsafe eval with asteval
Commit
b237d358b425 ("moveconfig: expand simple expressions") added
support for expanding expressions in configs, but used the unsafe python
built-in "eval". This patch fixes this by replacing eval with the
asteval module.
Signed-off-by: Markus Klotzbuecher <mk@mkio.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Sat, 22 Feb 2020 06:45:50 +0000 (07:45 +0100)]
MAINTAINERS: set maintainer for doc/api/efi.rst
doc/api/efi.rst belongs to the UEFI sub-system documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Wasim Khan [Fri, 14 Feb 2020 05:30:52 +0000 (11:00 +0530)]
arch: arm: Fix SZ_64K undeclared compilation error
Macro SZ_64K is undeclared. Include sizes.h to fix the compilation
error.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Philippe Reynes [Tue, 18 Feb 2020 16:23:20 +0000 (17:23 +0100)]
tools: image-host.c: remove uboot_aes.h
The include uboot_aes.h is not useful and
it breaks the compilation on android, so
we remove it.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reported-by: Praneeth Bajjuri <praneeth@ti.com>
Tom Rini [Tue, 25 Feb 2020 14:06:50 +0000 (09:06 -0500)]
Merge branch '2020-02-24-ci-htmldocs'
- Update our CI loops to run 'make htmldocs' and stop on errors
Heinrich Schuchardt [Fri, 21 Feb 2020 17:24:03 +0000 (18:24 +0100)]
doc/Makefile: turn warnings into errors
Several patches delivered incorrect restructured text as documentation. We
should be able to discover this in Travis CI, Gitlab CI, or Azure CI.
So let us turn all build warnings into errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Fri, 21 Feb 2020 17:24:02 +0000 (18:24 +0100)]
azure: build HTML documentation
Several patches delivered incorrect restructured text as documentation. We
should be able to discover this in Azure CI.
Provide a build step for 'make htmldocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Fri, 21 Feb 2020 17:24:01 +0000 (18:24 +0100)]
gitlab: build HTML documentation
Several patches delivered incorrect restructured text as documentation. We
should be able to discover this in Gitlab CI.
Provide a build step for 'make htmldocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Heinrich Schuchardt [Fri, 21 Feb 2020 17:24:00 +0000 (18:24 +0100)]
travis: build HTML docs
Several patches delivered incorrect restructured text as documentation.
We should be able to discover this in Travis CI.
Provide a build step for 'make htmldocs'.
Add required package graphviz.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Mon, 24 Feb 2020 20:10:36 +0000 (15:10 -0500)]
travis: Add python3-sphinx to the package list
In order to build htmldocs we need sphinx-build which comes from
python3-sphinx.
Signed-off-by: Tom Rini <trini@konsulko.com>
Peng Ma [Mon, 23 Dec 2019 09:28:18 +0000 (09:28 +0000)]
arch: powerpc: Rewrite the sata node to fit the driver
The sata of our powerpc platforms are updated. These changes is to
fit the driver probe.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Peng Ma [Mon, 23 Dec 2019 09:28:15 +0000 (09:28 +0000)]
Revert "configs: enable sata device module in T2080QDS"
This reverts commit
02dc1599ba0b16eb21ba0c206e5b6f38fe7b67a7
Commit
02dc1599ba0b ("configs: enable sata, eSDHC, USB device module in
T2080QDS")
has some sata defconfig changes to fit support DM mode, Now the driver
will be reverted, So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Peng Ma [Mon, 23 Dec 2019 09:28:12 +0000 (09:28 +0000)]
Revert "powerpc: mpc85xx: delete FSL_SATA for T2080QDS board."
This reverts commit
856b9cdb53f0e6c8d98f81cf71ef363c16b0aa0e.
Commit
856b9cdb53f0 ("powerpc: mpc85xx: delete FSL_SATA for T2080QDS
board.") is to fit support sata DM mode, Now the driver will be reverted,
So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Peng Ma [Mon, 23 Dec 2019 09:28:09 +0000 (09:28 +0000)]
Revert "ata: fsl_ahci: Add sata DM support for Freescale powerpc socs"
This reverts commit
1ee494291880fd51ef0c5f7342e072bdb069d7ff.
Commit
1ee494291880 ("ata: fsl_ahci: Add sata DM support for Freescale
powerpc socs") introduced SCSI layer to call AHCI private API in order
to support sata operations, In DM mode, This is not necessary for
non-AHCI sata. So revert it and have already updated the driver itself
to operate sata directly.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Heinrich Schuchardt [Fri, 21 Feb 2020 17:23:59 +0000 (18:23 +0100)]
doc: update doc/sphinx/kerneldoc.py
Update doc/sphinx/kerneldoc.py from Linux next-
20200219 to avoid warnings
like:
doc/sphinx/kerneldoc.py:125: RemovedInSphinx20Warning:
AutodocReporter is now deprecated. Use
sphinx.util.docutils.switch_source_input() instead.
self.state.memo.reporter =
AutodocReporter(result, self.state.memo.reporter)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tom Rini [Mon, 24 Feb 2020 16:04:29 +0000 (11:04 -0500)]
Azure / GitLab: Update Docker image
Bring in a newer Docker image to build on that has everything required
for running 'make htmldocs'.
Signed-off-by: Tom Rini <trini@konsulko.com>