Paul Gortmaker [Wed, 23 Jan 2013 20:13:32 +0000 (15:13 -0500)]
powerpc/85xx: add alternate dts file for sbc8548 boot via SODIMM
By moving the two JP12 jumpers 90 degrees, and switching the
setting of SW2.8, the sbc8548 can be configured to boot off
the alternate 64MB SODIMM, which when populated with u-boot
can be a handy recovery option, in case the u-boot in the
8MB soldered on flash gets corrupted. Here we add an alternate
dts file to match that configuration.
To better highlight the differences, the output from the u-boot
"fli" command is shown for the normal configuration and then
the alternate configuration.
Normal:
-----------------------
Bank # 1: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FF800000 E
FF820000 E
FF840000 E
FF860000 E
FF880000 E
[...]
FFEE0000 E
FFF00000 E
FFF20000 E
FFF40000 E
FFF60000 E
FFF80000 FFFA0000 RO
FFFC0000 RO
FFFE0000 RO
Bank # 2: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EC000000 E
EC080000 E
EC100000 E
EC180000 E
EC200000 E
[...]
EFC00000 E
EFC80000 E
EFD00000 E
EFD80000 E
EFE00000 E
EFE80000 E
EFF00000 EFF80000
-----------------------
Alternate:
-----------------------
Bank # 1: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FC000000 E
FC080000 E
FC100000 E
FC180000 E
FC200000 E
[...]
FFC00000 E
FFC80000 E
FFD00000 E
FFD80000 E
FFE00000 E
FFE80000 E
FFF00000 RO
FFF80000 RO
Bank # 2: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EF800000 E
EF820000 E
EF840000 E
EF860000 E
EF880000 E
[...]
EFEE0000 E
EFF00000 E
EFF20000 E
EFF40000 E
EFF60000 E
EFF80000 E
EFFA0000 EFFC0000 EFFE0000
-----------------------
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Wed, 23 Jan 2013 20:13:31 +0000 (15:13 -0500)]
powerpc/85xx: update sbc8548 flash information to match recent u-boot
The original memory map for the sbc8548 had the 64MB SODIMM flash
device misaligned by 8MB to allow a window of address space for
the soldered on 8MB device -- i.e.
start end CS<n> width Desc.
----------------------------------------------------------
fb80_0000 ff7f_ffff CS6 32 SODIMM flash (64MB)
ff80_0000 ffff_ffff CS0 8 Boot flash (8MB)
However, if we want to change the configuration so that it boots
off the 64MB flash, it is in turn then aligned with a 64MB boundary,
starting at fc00_0000 (and the 8MB @ fb80_0000 -> fbff_ffff).
This makes for complicated updates, since what is the beginning
of the physical device is 8MB into its address space in the default
configuration shown above.
This issue was fixed as of u-boot commit
3fd673cf363bc86ed42eff713d4
("sbc8548: relocate 64MB user flash to sane boundary") -- in which
the SODIMM was mapped to ec00_0000 (natively aligned under efff_ffff)
and so when JP12/SW2.8 are switched, it will be a a simple 0xec --> 0xfc
mapping between the two instances.
Here we make the associated changes in the localbus flash memory
map in the dts file: indicating the 64MB device starts at ec00_0000
and that the tail end of the 64MB device (last 2 sectors) can contain
a bootloader image.
The partitions for both flash devices get a clean-up; there were
non-meaningful assignments in there that probably originated from
the MPC8548CDS on which the file was based on. Now there is just
the categorization of free space and bootloader images.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Paul Gortmaker [Wed, 23 Jan 2013 20:13:30 +0000 (15:13 -0500)]
powerpc/85xx: split sbc8548 dts file into pre and post chunks
Updates to u-boot allow this board to boot off of either
the 8MB soldered on flash, or the 64MB SODIMM flash.
This is achieved by changing JP12 and SW2.8 which in turn
swaps which flash device appears on /CS0 and /CS6 respectively.
Since the flash devices are not the same size, this also
changes the MTD memory map layout on the local bus.
Here we split the common chunks out into a pre and post
include, so they can be reused by an upcoming "alternative
boot" dts file; leaving only the local bus chunk behind.
No content changes are made at this point - it is just purely
the move to using include files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Wei Yongjun [Mon, 3 Dec 2012 13:36:03 +0000 (08:36 -0500)]
powerpc/85xx: use for_each_compatible_node() macro
Use for_each_compatible_node() macro instead of open coding it.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kim Phillips [Fri, 30 Nov 2012 23:34:59 +0000 (17:34 -0600)]
powerpc/fsl: msi: sparse fixes
arch/powerpc/sysdev/fsl_msi.c:31:1: warning: symbol 'msi_head' was not declared. Should it be static?
arch/powerpc/sysdev/fsl_msi.c:138:40: warning: incorrect type in argument 1 (different base types)
arch/powerpc/sysdev/fsl_msi.c:138:40: expected restricted __be64 const [usertype] *p
arch/powerpc/sysdev/fsl_msi.c:138:40: got unsigned long long const [usertype] *[assigned] reg
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kim Phillips [Fri, 30 Nov 2012 23:35:01 +0000 (17:35 -0600)]
powerpc/fsl: ifc: sparse fixes
arch/powerpc/sysdev/fsl_ifc.c:66:38: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_ifc.c:66:38: expected restricted __be32 [usertype] cspr
arch/powerpc/sysdev/fsl_ifc.c:66:38: got unsigned int
arch/powerpc/sysdev/fsl_ifc.c:67:21: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_ifc.c:67:39: warning: restricted __be32 degrades to integer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kim Phillips [Fri, 30 Nov 2012 23:35:02 +0000 (17:35 -0600)]
powerpc/fsl: fsl_soc: sparse fixes
arch/powerpc/sysdev/fsl_soc.c:70:67: warning: incorrect type in argument 2 (different base types)
arch/powerpc/sysdev/fsl_soc.c:70:67: expected restricted __be32 const [usertype] *addr
arch/powerpc/sysdev/fsl_soc.c:70:67: got unsigned int const [usertype] *
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kim Phillips [Fri, 30 Nov 2012 23:35:00 +0000 (17:35 -0600)]
powerpc/fsl: lbc: sparse fixes
arch/powerpc/sysdev/fsl_lbc.c:77:36: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_lbc.c:77:36: expected restricted __be32 [usertype] br
arch/powerpc/sysdev/fsl_lbc.c:77:36: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:78:36: warning: incorrect type in initializer (different base types)
arch/powerpc/sysdev/fsl_lbc.c:78:36: expected restricted __be32 [usertype] or
arch/powerpc/sysdev/fsl_lbc.c:78:36: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:80:21: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:80:38: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:111:12: warning: incorrect type in assignment (different base types)
arch/powerpc/sysdev/fsl_lbc.c:111:12: expected restricted __be32 [usertype] br
arch/powerpc/sysdev/fsl_lbc.c:111:12: got unsigned int
arch/powerpc/sysdev/fsl_lbc.c:113:17: warning: restricted __be32 degrades to integer
arch/powerpc/sysdev/fsl_lbc.c:127:17: warning: restricted __be32 degrades to integer
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ian Munsie [Thu, 7 Feb 2013 15:46:58 +0000 (15:46 +0000)]
powerpc: Add support for context switching the TAR register
This patch adds support for enabling and context switching the Target
Address Register in Power8. The TAR is a new special purpose register
that can be used for computed branches with the bctar[l] (branch
conditional to TAR) instruction in the same manner as the count and link
registers.
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nishanth Aravamudan [Mon, 28 Jan 2013 16:03:58 +0000 (16:03 +0000)]
pseries/iommu: Remove DDW on kexec
pseries/iommu: remove DDW on kexec
We currently insert a property in the device-tree when we successfully
configure DDW for a given slot. This was meant to be an optimization to
speed up kexec/kdump, so that we don't need to make the RTAS calls again
to re-configured DDW in the new kernel.
However, we end up tripping a plpar_tce_stuff failure on kexec/kdump
because we unconditionally parse the ibm,dma-window property for the
node at bus/dev setup time. This property contains the 32-bit DMA window
LIOBN, which is distinct from the DDW window's. We pass that LIOBN (via
iommu_table_init -> iommu_table_clear -> tce_free ->
tce_freemulti_pSeriesLP) to plpar_tce_stuff, which fails because that
32-bit window is no longer present after
25ebc45b93452d0bc60271f178237123c4b26808 ("powerpc/pseries/iommu: remove
default window before attempting DDW manipulation").
I believe the simplest, easiest-to-maintain fix is to just change our
initcall to, rather than detecting and updating the new kernel's DDW
knowledge, just remove all DDW configurations. When the drivers
re-initialize, we will set everything back up as it was before.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nishanth Aravamudan [Mon, 28 Jan 2013 16:02:46 +0000 (16:02 +0000)]
pseries/iommu: Restore_default_window does not use liobn parameter
The parameter is unused, and complicates a following fix. Just remove
it.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Daniel Borkmann [Tue, 5 Feb 2013 05:07:06 +0000 (05:07 +0000)]
powerpc: fix ics_rtas_init and start_secondary section mismatch
It seems, we're fine with just annotating the two functions.
Thus, this fixes the following build warnings on ppc64:
WARNING: arch/powerpc/sysdev/xics/built-in.o(.text+0x1664):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x6044):
The function .ics_rtas_init() references
the function __init .xics_register_ics().
This is often because .ics_rtas_init lacks a __init
annotation or the annotation of .xics_register_ics is wrong.
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2db30):
The function .start_secondary() references
the function __cpuinit .vdso_getcpu_init().
This is often because .start_secondary lacks a __cpuinit
annotation or the annotation of .vdso_getcpu_init is wrong.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nishanth Aravamudan [Fri, 18 Jan 2013 09:17:36 +0000 (09:17 +0000)]
pseries/iommu: Ensure TCEs are cleared with non-huge DDW
There are now two kinds of DMA windows that might be presented by
PowerVM DDW support -- huge windows (that can map all of system memory
regardless of the LPAR configuration) and non-huge windows (which
can't). They are implemented slightly differently in PowerVM, and thus
have different characteristics. The most obvious is that slot isolate
doesn't clear the TCEs/window for us with non-huge windows. Thus, when a
DLPAR operation occurs on a slot using a non-huge window, TCEs are still
present (the notifier chain doesn't currently remove them explicitly)
and the DLPAR fails. Fix this by calling remove_ddw() first, which will
unmap the DDW TCEs.
Note: a corresponding change to drmgr is needed to actually successfully
DLPAR, such that the device-tree update (which causes the notifier chain
to fire) occurs before slot isolate.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Nishanth Aravamudan [Fri, 18 Jan 2013 09:16:24 +0000 (09:16 +0000)]
pseries/iommu: Fix iteration in DDW TCE clearrange
tce_clearrange_multi_pSeriesLP is attempting to iterate over all TCEs in
a given range. However, is it not advancing the dma_offset value passed
to plpar_tce_stuff via the next value. This prevents DLPAR from
completing, because TCEs are still present at slot isolation time.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Thu, 24 Jan 2013 15:02:59 +0000 (15:02 +0000)]
powerpc: Change hardware breakpoint to allow longer ranges
Change the hardware breakpoint code so that we can support wider ranged
breakpoints.
This means both ptrace and perf hardware breakpoints can use upto 512 byte long
breakpoints when using the DAWR and only 8 byte when using the DABR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Thu, 24 Jan 2013 15:02:58 +0000 (15:02 +0000)]
powerpc: Add length setting to set_dawr
Currently we set the length field in the DAWR to 0 which defaults it to one
double word (64bits) which is the same as the DABR.
Change this so that we can set it to longer values as supported by the DAWR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
sukadev@linux.vnet.ibm.com [Thu, 24 Jan 2013 13:25:23 +0000 (13:25 +0000)]
perf/Power: PERF_EVENT_IOC_ENABLE does not reenable event
perf/Power: PERF_EVENT_IOC_ENABLE does not reenable event
If we disable a perf event because we exceeded the specified ->event_limit,
power_pmu_stop() sets the PERF_HES_STOPPED flag on the event.
If the application then re-enables the event using PERF_EVENT_IOC_ENABLE
ioctl, we don't ever clear this STOPPED flag. Consequently, the user space
is never notified of the event.
Following message has more background and test case.
http://lists.eecs.utk.edu/pipermail/ptools-perfapi/2012-October/002528.html
Used the following test cases to verify that this patch works on latest PAPI.
$ papi.git/src/ctests/nonthread PAPI_TOT_CYC@5000000
$ papi.git/src/ctests/overflow_single_event
Changelog[v2]:
- [Paul Mackerras] Also clear PERF_HES_UPTODATE flag since we are
restarting the event; cleanup comments and patch description.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Thu, 24 Jan 2013 21:51:13 +0000 (21:51 +0000)]
powerpc: Avoid debug_smp_processor_id() check in SHARED_PROCESSOR
Use local_paca directly in macro SHARED_PROCESSOR, as all processors
have the same value for the field shared_proc, so we don't need care
racy here.
Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Suzuki K. Poulose [Mon, 7 Jan 2013 00:26:57 +0000 (00:26 +0000)]
uprobes/powerpc: Add dependency on single step emulation
Uprobes uses emulate_step in sstep.c, but we haven't explicitly specified
the dependency. On pseries HAVE_HW_BREAKPOINT protects us, but 44x has no
such luxury.
Consolidate other users that depend on sstep and create a new config option.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Cc: linuxppc-dev@ozlabs.org
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Collins [Mon, 17 Dec 2012 04:19:28 +0000 (04:19 +0000)]
powerpc: Add support for CTS-1000 GPIO controlled system poweroff
CTS-1000 is based on P4080. GPIO 27 is used to signal the FPGA to
switch off power, and also associates IRQ 8 with front-panel button
press (which we use to call orderly_poweroff()).
The relevant device-tree looks like this:
gpio0: gpio@130000 {
compatible = "fsl,qoriq-gpio";
reg = <0x130000 0x1000>;
interrupts = <55 2 0 0>;
#gpio-cells = <2>;
gpio-controller;
/* Allows powering off the system via GPIO signal. */
gpio-halt@27 {
compatible = "sgy,gpio-halt";
gpios = <&gpio0 27 0>;
interrupts = <8 1 0 0>;
};
};
Because the driver cannot match on sgy,gpio-halt (because the node is never
processed through of_platform), it matches on fsl,qoriq-gpio and then
checks child nodes for the matching sgy,gpio-halt. This also ensures that
the GPIO controller is detected prior to sgy_cts1000's probe callback,
since that node wont match via of_platform until the controller is
registered.
Also, because the GPIO handler for triggering system poweroff might sleep,
the IRQ uses a workqueue to call orderly_poweroff().
As a final note, this driver may be expanded for other features specific to
the CTS-1000.
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Jack Smith <jack.s@servergy.com>
Cc: Vihar Rai <vihar.r@servergy.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Fri, 11 Jan 2013 13:38:41 +0000 (13:38 +0000)]
powerpc/fsl: Remove CONFIG_IRQ_ALL_CPUS from mpc85xx/mpc86xx defconfig
While this should be harmless now that distribute_irqs
obeys MPIC_SINGLE_DEST_CPU, there's no reason to enable this
on mpc85xx/mpc86xx since MPIC_SINGLE_DEST_CPU will always be set.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Scott Wood [Fri, 11 Jan 2013 13:38:40 +0000 (13:38 +0000)]
powerpc/mpic: Make distribute_irqs obey MPIC_SINGLE_DEST_CPU
Previously we were setting an illegal configuration on mpc85xx
MPICs if CONFIG_IRQ_ALL_CPUS is enabled (which for some reason it is
in mpc85xx_smp_defconfig).
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Michael Neuling [Tue, 8 Jan 2013 18:45:36 +0000 (18:45 +0000)]
powerpc/ptrace: Make #defines for all request numbers hex
We have a mix of decimal and hex here, so lets make them consistently
hex. Also, strace will print them in hex if it can't decode them, so
having them in hex here makes it easier to match up.
No functional change.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cody P Schafer [Wed, 9 Jan 2013 12:40:18 +0000 (12:40 +0000)]
powerpc/mm: Eliminate unneeded for_each_memblock
The only persistent change made by this loop is calling
memblock_set_node() once for each memblock, which is not useful (and has
no effect) as memblock_set_node() is not called with any
memblock-specific parameters.
Subsistute a single memblock_set_node().
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Benjamin Herrenschmidt [Tue, 29 Jan 2013 00:33:37 +0000 (11:33 +1100)]
Merge branch 'merge' into next
Merge "merge" branch to bring in various bug fixes that are
going into 3.8
Tiejun Chen [Tue, 15 Jan 2013 17:01:19 +0000 (17:01 +0000)]
powerpc: Max next_tb to prevent from replaying timer interrupt
With lazy interrupt, we always call __check_irq_replaysome with
decrementers_next_tb to check if we need to replay timer interrupt.
So in hotplug case we also need to set decrementers_next_tb as MAX
to make sure __check_irq_replay don't replay timer interrupt
when return as we expect, otherwise we'll trap here infinitely.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cong Ding [Mon, 14 Jan 2013 07:26:32 +0000 (07:26 +0000)]
powerpc: kernel/kgdb.c: Fix memory leakage
the variable backup_current_thread_info isn't freed before existing the
function.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tiejun Chen [Sun, 6 Jan 2013 00:49:34 +0000 (00:49 +0000)]
powerpc/book3e: Disable interrupt after preempt_schedule_irq
In preempt case current arch_local_irq_restore() from
preempt_schedule_irq() may enable hard interrupt but we really
should disable interrupts when we return from the interrupt,
and so that we don't get interrupted after loading SRR0/1.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Carl E. Love [Thu, 29 Nov 2012 06:42:03 +0000 (06:42 +0000)]
powerpc/oprofile: Fix error in oprofile power7_marked_instr_event() function
The calculation for the left shift of the mask OPROFILE_PM_PMCSEL_MSK has an
error. The calculation is should be to shift left by (max_cntrs - cntr) times
the width of the pmsel field width. However, the #define OPROFILE_MAX_PMC_NUM
was used instead of OPROFILE_PMSEL_FIELD_WIDTH. This patch fixes the
calculation.
Signed-off-by: Carl Love <cel@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Steven Rostedt [Mon, 21 Jan 2013 17:23:26 +0000 (17:23 +0000)]
powerpc/pasemi: Fix crash on reboot
commit
f96972f2dc "kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()"
added a call to disable_nonboot_cpus() on kernel_restart(), which tries
to shutdown all the CPUs except the first one. The issue with the PA
Semi, is that it does not support CPU hotplug.
When the call is made to __cpu_down(), it calls the notifiers
CPU_DOWN_PREPARE, and then tries to take the CPU down.
One of the notifiers to the CPU hotplug code, is the cpufreq. The
DOWN_PREPARE will call __cpufreq_remove_dev() which calls
cpufreq_driver->exit. The PA Semi exit handler unmaps regions of I/O
that is used by an interrupt that goes off constantly
(system_reset_common, but it goes off during normal system operations
too). I'm not sure exactly what this interrupt does.
Running a simple function trace, you can see it goes off quite a bit:
# tracer: function
#
# TASK-PID CPU# TIMESTAMP FUNCTION
# | | | | |
<idle>-0 [001] 1558.859363: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.860112: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861109: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [001] 1558.861361: .pasemi_system_reset_exception <-.system_reset_exception
<idle>-0 [000] 1558.861437: .pasemi_system_reset_exception <-.system_reset_exception
When the region is unmapped, the system crashes with:
Disabling non-boot CPUs ...
Error taking CPU1 down: -38
Unable to handle kernel paging request for data at address 0xd0000800903a0100
Faulting instruction address: 0xc000000000055fcc
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=64 NUMA PA Semi PWRficient
Modules linked in: shpchp
NIP:
c000000000055fcc LR:
c000000000055fb4 CTR:
c0000000000df1fc
REGS:
c0000000012175d0 TRAP: 0300 Not tainted (3.8.0-rc4-test-dirty)
MSR:
9000000000009032 <SF,HV,EE,ME,IR,DR,RI> CR:
24000088 XER:
00000000
SOFTE: 0
DAR:
d0000800903a0100, DSISR:
42000000
TASK =
c0000000010e9008[0] 'swapper/0' THREAD:
c000000001214000 CPU: 0
GPR00:
d0000800903a0000 c000000001217850 c0000000012167e0 0000000000000000
GPR04:
0000000000000000 0000000000000724 0000000000000724 0000000000000000
GPR08:
0000000000000000 0000000000000000 0000000000000001 0000000000a70000
GPR12:
0000000024000080 c00000000fff0000 ffffffffffffffff 000000003ffffae0
GPR16:
ffffffffffffffff 0000000000a21198 0000000000000060 0000000000000000
GPR20:
00000000008fdd35 0000000000a21258 000000003ffffaf0 0000000000000417
GPR24:
0000000000a226d0 c000000000000000 0000000000000000 0000000000000000
GPR28:
c00000000138b358 0000000000000000 c000000001144818 d0000800903a0100
NIP [
c000000000055fcc] .set_astate+0x5c/0xa4
LR [
c000000000055fb4] .set_astate+0x44/0xa4
Call Trace:
[
c000000001217850] [
c000000000055fb4] .set_astate+0x44/0xa4 (unreliable)
[
c0000000012178f0] [
c00000000005647c] .restore_astate+0x2c/0x34
[
c000000001217980] [
c000000000054668] .pasemi_system_reset_exception+0x6c/0x88
[
c000000001217a00] [
c000000000019ef0] .system_reset_exception+0x48/0x84
[
c000000001217a80] [
c000000000001e40] system_reset_common+0x140/0x180
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Li Zhong [Sun, 2 Dec 2012 20:19:22 +0000 (20:19 +0000)]
powerpc: Fix MAX_STACK_TRACE_ENTRIES too low warning for ppc32
This patch fixes MAX_STACK_TRACE_ENTRIES too low warning for ppc32,
which is similar to commit
12660b17.
Reported-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Linus Torvalds [Mon, 28 Jan 2013 19:53:49 +0000 (11:53 -0800)]
Merge git://git./linux/kernel/git/steve/gfs2-3.0-fixes
Pull GFS2 fix from Steven Whitehouse.
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: fix skip unlock condition
Linus Torvalds [Mon, 28 Jan 2013 19:52:56 +0000 (11:52 -0800)]
Merge tag 'iommu-fixes-v3.8-rc5' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"One fix for the AMD IOMMU driver to work around broken BIOSes found in
the field. Some BIOSes forget to enable a workaround for a hardware
problem which might cause the IOMMU to stop working under high load
conditions. The fix makes sure this workaround is enabled."
* tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
Linus Torvalds [Mon, 28 Jan 2013 19:51:57 +0000 (11:51 -0800)]
Merge tag 'mfd-for-linus-3.8-1' of git://git./linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
Linus Torvalds [Mon, 28 Jan 2013 19:41:37 +0000 (11:41 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking updates from David Miller:
"Much more accumulated than I would have liked due to an unexpected
bout with a nasty flu:
1) AH and ESP input don't set ECN field correctly because the
transport head of the SKB isn't set correctly, fix from Li
RongQing.
2) If netfilter conntrack zones are disabled, we can return an
uninitialized variable instead of the proper error code. Fix from
Borislav Petkov.
3) Fix double SKB free in ath9k driver beacon handling, from Felix
Feitkau.
4) Remove bogus assumption about netns cleanup ordering in
nf_conntrack, from Pablo Neira Ayuso.
5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
Dumazet. It uses spin_is_locked() in it's test and is therefore
unsuitable for UP.
6) Fix SELINUX labelling regressions added by the tuntap multiqueue
changes, from Paul Moore.
7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
Nayak Sujir.
8) CXGB4 driver sets interrupt coalescing parameters only on first
queue, rather than all of them. Fix from Thadeu Lima de Souza
Cascardo.
9) Fix regression in the dispatch of read/write registers in dm9601
driver, from Tushar Behera.
10) ipv6_append_data miscalculates header length, from Romain KUNTZ.
11) Fix PMTU handling regressions on ipv4 routes, from Steffen
Klassert, Timo Teräs, and Julian Anastasov.
12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
expression. From Nickolai Zeldovich.
13) macvlan_get_size() causes underallocation netlink message space,
fix from Eric Dumazet.
14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
Zeldovich. Amusingly the zero check was already there, we were
just performing it after the modulus :-)
15) Some more splice bug fixes from Eric Dumazet, which fix things
mostly eminating from how we now more aggressively use high-order
pages in SKBs.
16) Fix size calculation bug when freeing hash tables in the IPSEC
xfrm code, from Michal Kubecek.
17) Fix PMTU event propagation into socket cached routes, from Steffen
Klassert.
18) Fix off by one in TX buffer release in netxen driver, from Eric
Dumazet.
19) Fix rediculous memory allocation requirements introduced by the
tuntap multiqueue changes, from Jason Wang.
20) Remove bogus AMD platform workaround in r8169 driver that causes
major problems in normal operation, from Timo Teräs.
21) virtio-net set affinity and select queue don't handle
discontiguous cpu numbers properly, fix from Wanlong Gao.
22) Fix a route refcounting issue in loopback driver, from Eric
Dumazet. There's a similar fix coming that we might add to the
macvlan driver as well.
23) Fix SKB leaks in batman-adv's distributed arp table code, from
Matthias Schiffer.
24) r8169 driver gives descriptor ownership back the hardware before
we're done reading the VLAN tag out of it, fix from Francois
Romieu.
25) Checksums not calculated properly in GRE tunnel driver fix from
Pravin B Shelar.
26) Fix SCTP memory leak on namespace exit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
dm9601: support dm9620 variant
SCTP: Free the per-net sysctl table on net exit. v2
net: phy: icplus: fix broken INTR pin settings
net: phy: icplus: Use the RGMII interface mode to configure clock delays
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
sctp: set association state to established in dupcook_a handler
ip6mr: limit IPv6 MRT_TABLE identifiers
r8169: fix vlan tag read ordering.
net: cdc_ncm: use IAD provided by the USB core
batman-adv: filter ARP packets with invalid MAC addresses in DAT
batman-adv: check for more types of invalid IP addresses in DAT
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
net: loopback: fix a dst refcounting issue
virtio-net: reset virtqueue affinity when doing cpu hotplug
virtio-net: split out clean affinity function
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
can: pch_can: fix invalid error codes
can: ti_hecc: fix invalid error codes
can: c_can: fix invalid error codes
r8169: remove the obsolete and incorrect AMD workaround
...
Suravee Suthikulpanit [Thu, 24 Jan 2013 19:17:53 +0000 (13:17 -0600)]
IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.
BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
David Teigland [Thu, 3 Jan 2013 22:52:07 +0000 (17:52 -0500)]
GFS2: fix skip unlock condition
The recent commit
fb6791d100d1bba20b5cdbc4912e1f7086ec60f8
included the wrong logic. The lvbptr check was incorrectly
added after the patch was tested.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Peter Korsgaard [Sun, 27 Jan 2013 12:34:22 +0000 (12:34 +0000)]
dm9601: support dm9620 variant
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to SÅ‚awek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 24 Jan 2013 16:02:47 +0000 (11:02 -0500)]
SCTP: Free the per-net sysctl table on net exit. v2
Per-net sysctl table needs to be explicitly freed at
net exit. Otherwise we see the following with kmemleak:
unreferenced object 0xffff880402d08000 (size 2048):
comm "chrome_sandbox", pid 18437, jiffies
4310887172 (age 9097.630s)
hex dump (first 32 bytes):
b2 68 89 81 ff ff ff ff 20 04 04 f8 01 88 ff ff .h...... .......
04 00 00 00 a4 01 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff815b4aad>] kmemleak_alloc+0x21/0x3e
[<
ffffffff81110352>] slab_post_alloc_hook+0x28/0x2a
[<
ffffffff81113fad>] __kmalloc_track_caller+0xf1/0x104
[<
ffffffff810f10c2>] kmemdup+0x1b/0x30
[<
ffffffff81571e9f>] sctp_sysctl_net_register+0x1f/0x72
[<
ffffffff8155d305>] sctp_net_init+0x100/0x39f
[<
ffffffff814ad53c>] ops_init+0xc6/0xf5
[<
ffffffff814ad5b7>] setup_net+0x4c/0xd0
[<
ffffffff814ada5e>] copy_net_ns+0x6d/0xd6
[<
ffffffff810938b1>] create_new_namespaces+0xd7/0x147
[<
ffffffff810939f4>] copy_namespaces+0x63/0x99
[<
ffffffff81076733>] copy_process+0xa65/0x1233
[<
ffffffff81077030>] do_fork+0x10b/0x271
[<
ffffffff8100a0e9>] sys_clone+0x23/0x25
[<
ffffffff815dda73>] stub_clone+0x13/0x20
[<
ffffffffffffffff>] 0xffffffffffffffff
I fixed the spelling of sysctl_header so the code actually
compiles. -- EWB.
Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Wed, 23 Jan 2013 00:22:37 +0000 (00:22 +0000)]
net: phy: icplus: fix broken INTR pin settings
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stuart Menefy [Wed, 23 Jan 2013 00:22:36 +0000 (00:22 +0000)]
net: phy: icplus: Use the RGMII interface mode to configure clock delays
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Wed, 23 Jan 2013 11:45:42 +0000 (11:45 +0000)]
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM. Following patch fixes it by
using correct csum API.
Bug introduced in commit
6b78f16e4bdde3936b (gre: add GSO support)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xufeng Zhang [Wed, 23 Jan 2013 16:44:34 +0000 (16:44 +0000)]
sctp: set association state to established in dupcook_a handler
While sctp handling a duplicate COOKIE-ECHO and the action is
'Association restart', sctp_sf_do_dupcook_a() will processing
the unexpected COOKIE-ECHO for peer restart, but it does not set
the association state to SCTP_STATE_ESTABLISHED, so the association
could stuck in SCTP_STATE_SHUTDOWN_PENDING state forever.
This violates the sctp specification:
RFC 4960 5.2.4. Handle a COOKIE ECHO when a TCB Exists
Action
A) In this case, the peer may have restarted. .....
After this, the endpoint shall enter the ESTABLISHED state.
To resolve this problem, adding a SCTP_CMD_NEW_STATE cmd to the
command list before SCTP_CMD_REPLY cmd, this will set the restart
association to SCTP_STATE_ESTABLISHED state properly and also avoid
I-bit being set in the DATA chunk header when COOKIE_ACK is bundled
with DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 23 Jan 2013 20:38:34 +0000 (20:38 +0000)]
ip6mr: limit IPv6 MRT_TABLE identifiers
We did this for IPv4 in
b49d3c1e1c "net: ipmr: limit MRT_TABLE
identifiers" but we need to do it for IPv6 as well. On IPv6 the name
is "pim6reg" instead of "pimreg" so there is one less digit allowed.
The strcpy() is in ip6mr_reg_vif().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Thu, 24 Jan 2013 13:30:06 +0000 (13:30 +0000)]
r8169: fix vlan tag read ordering.
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 25 Jan 2013 23:36:59 +0000 (23:36 +0000)]
net: cdc_ncm: use IAD provided by the USB core
commit 9992c2e (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant. The USB core has already done the lookup
and saved the result in the USB interface struct. Use that
instead.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Jan 2013 00:10:36 +0000 (19:10 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes ares:
- fix an skb memleak in DAT
- fix the ARP filtering routine in DAT by preventing bogus entries to overwrite
already existing ones in the local cache.
- fix the ARP filtering routine in DAT by preventing it to parse and add to the
cache bogus entries
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Schiffer [Thu, 24 Jan 2013 17:18:27 +0000 (18:18 +0100)]
batman-adv: filter ARP packets with invalid MAC addresses in DAT
We never want multicast MAC addresses in the Distributed ARP Table, so it's
best to completely ignore ARP packets containing them where we expect unicast
addresses.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Matthias Schiffer [Thu, 24 Jan 2013 17:18:26 +0000 (18:18 +0100)]
batman-adv: check for more types of invalid IP addresses in DAT
There are more types of IP addresses that may appear in ARP packets that we
don't want to process. While some of these should never appear in sane ARP
packets, a 0.0.0.0 source is used for duplicate address detection and thus seen
quite often.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Matthias Schiffer [Wed, 23 Jan 2013 17:11:53 +0000 (18:11 +0100)]
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
The callers of batadv_dat_snoop_incoming_arp_reply() assume the skb has been
freed when it returns true; fix this by calling kfree_skb before returning as
it is done in batadv_dat_snoop_incoming_arp_request().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
David S. Miller [Sun, 27 Jan 2013 06:37:22 +0000 (01:37 -0500)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
This is a batch of fixes intende for the 3.8 stream.
Regarding the iwlwifi bits, Johannes says this:
"Please pull to get a single fix from Emmanuel for a bug I introduced due
to misunderstanding the code."
Regarding the mac80211 bits, Johannes says this:
"I have a few small fixes for you:
* some mesh frames would cause encryption warnings -- fixes from Bob
* scanning would pretty much break an association if we transmitted
anything to the AP while scanning -- fix from Stanislaw
* mode injection was broken by channel contexts -- fix from Felix
* FT roaming was broken: hardware crypto would get disabled by it"
Along with that, a handful of other fixes confined to specific drivers.
Avinash Patil fixes a typo in a NULL check in mwifiex.
Larry Finger fixes a build warning in rtlwifi. Seems safe...
Stanislaw Gruszka fixes iwlegacy to prevent microcode errors when
switching from IBSS mode to STA mode.
Felix Fietkau provides a trio of ath9k fixes related to proper tuning.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 25 Jan 2013 07:44:41 +0000 (07:44 +0000)]
net: loopback: fix a dst refcounting issue
Ben Greear reported crashes in ip_rcv_finish() on a stress
test involving many macvlans.
We tracked the bug to a dst use after free. ip_rcv_finish()
was calling dst->input() and got garbage for dst->input value.
It appears the bug is in loopback driver, lacking
a skb_dst_force() before calling netif_rx().
As a result, a non refcounted dst, normally protected by a
RCU read_lock section, was escaping this section and could
be freed before the packet being processed.
[<
ffffffff813a3c4d>] loopback_xmit+0x64/0x83
[<
ffffffff81477364>] dev_hard_start_xmit+0x26c/0x35e
[<
ffffffff8147771a>] dev_queue_xmit+0x2c4/0x37c
[<
ffffffff81477456>] ? dev_hard_start_xmit+0x35e/0x35e
[<
ffffffff8148cfa6>] ? eth_header+0x28/0xb6
[<
ffffffff81480f09>] neigh_resolve_output+0x176/0x1a7
[<
ffffffff814ad835>] ip_finish_output2+0x297/0x30d
[<
ffffffff814ad6d5>] ? ip_finish_output2+0x137/0x30d
[<
ffffffff814ad90e>] ip_finish_output+0x63/0x68
[<
ffffffff814ae412>] ip_output+0x61/0x67
[<
ffffffff814ab904>] dst_output+0x17/0x1b
[<
ffffffff814adb6d>] ip_local_out+0x1e/0x23
[<
ffffffff814ae1c4>] ip_queue_xmit+0x315/0x353
[<
ffffffff814adeaf>] ? ip_send_unicast_reply+0x2cc/0x2cc
[<
ffffffff814c018f>] tcp_transmit_skb+0x7ca/0x80b
[<
ffffffff814c3571>] tcp_connect+0x53c/0x587
[<
ffffffff810c2f0c>] ? getnstimeofday+0x44/0x7d
[<
ffffffff810c2f56>] ? ktime_get_real+0x11/0x3e
[<
ffffffff814c6f9b>] tcp_v4_connect+0x3c2/0x431
[<
ffffffff814d6913>] __inet_stream_connect+0x84/0x287
[<
ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
[<
ffffffff8108d695>] ? _local_bh_enable_ip+0x84/0x9f
[<
ffffffff8108d6c8>] ? local_bh_enable+0xd/0x11
[<
ffffffff8146763c>] ? lock_sock_nested+0x6e/0x79
[<
ffffffff814d6b38>] ? inet_stream_connect+0x22/0x49
[<
ffffffff814d6b49>] inet_stream_connect+0x33/0x49
[<
ffffffff814632c6>] sys_connect+0x75/0x98
This bug was introduced in linux-2.6.35, in commit
7fee226ad2397b (net: add a noref bit on skb dst)
skb_dst_force() is enforced in dev_queue_xmit() for devices having a
qdisc.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wanlong Gao [Thu, 24 Jan 2013 23:51:31 +0000 (23:51 +0000)]
virtio-net: reset virtqueue affinity when doing cpu hotplug
Add a cpu notifier to virtio-net, so that we can reset the
virtqueue affinity if the cpu hotplug happens. It improve
the performance through enabling or disabling the virtqueue
affinity after doing cpu hotplug.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wanlong Gao [Thu, 24 Jan 2013 23:51:30 +0000 (23:51 +0000)]
virtio-net: split out clean affinity function
Split out the clean affinity function to virtnet_clean_affinity().
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wanlong Gao [Thu, 24 Jan 2013 23:51:29 +0000 (23:51 +0000)]
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
As Michael mentioned, set affinity and select queue will not work very
well when CPU IDs are not consecutive, this can happen with hot unplug.
Fix this bug by traversal the online CPUs, and create a per cpu variable
to find the mapping from CPU to the preferable virtual-queue.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Dumazet <erdnetdev@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei WANG [Sun, 27 Jan 2013 00:55:16 +0000 (01:55 +0100)]
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
If rtsx_pci_sdmmc is not probed, function pointer pcr->slots[].card_event
will point to NULL, and thus rtsx_pci_card_detect will reference a NULL
pointer.
Check card_event pointer before referencing it can avoid kernel panic.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Mark Brown [Fri, 25 Jan 2013 15:53:51 +0000 (23:53 +0800)]
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
Updated in latest datasheet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Arnd Bergmann [Fri, 25 Jan 2013 14:14:26 +0000 (14:14 +0000)]
mfd: twl4030: Don't warn about uninitialized return code
If the twl4030_write_script function gets called with
a zero length argument, its return value does not
get set. We know that all scripts have a nonzero
length, but returning an error in case they ever
do is probably appropriate.
Without this patch, building omap2plus_defconfig results in:
drivers/mfd/twl4030-power.c: In function 'load_twl4030_script':
drivers/mfd/twl4030-power.c:414:5: error: 'err' may be used uninitialized in this function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: "Kristo, Tero" <t-kristo@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ashish Jangam [Fri, 25 Jan 2013 08:33:49 +0000 (14:03 +0530)]
mfd: da9052/53 lockup fix
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Wei WANG [Wed, 23 Jan 2013 01:51:06 +0000 (09:51 +0800)]
mfd: rtsx: Add clock divider hook
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Wei WANG [Wed, 23 Jan 2013 01:51:05 +0000 (09:51 +0800)]
mmc: rtsx: Call MFD hook to switch output voltage
Different card reader has different method to switch output voltage, so
we have to use the callback function provided by MFD driver to switch
output pad voltage.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Wei WANG [Wed, 23 Jan 2013 01:51:04 +0000 (09:51 +0800)]
mfd: rtsx: Add output voltage switch hook
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Olivier Sobrie [Fri, 18 Jan 2013 08:32:41 +0000 (09:32 +0100)]
can: pch_can: fix invalid error codes
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Olivier Sobrie [Fri, 18 Jan 2013 08:32:40 +0000 (09:32 +0100)]
can: ti_hecc: fix invalid error codes
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Anant Gole <anantgole@ti.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Olivier Sobrie [Fri, 18 Jan 2013 08:32:39 +0000 (09:32 +0100)]
can: c_can: fix invalid error codes
Errors in CAN protocol (location) are reported in data[3] of the can
frame instead of data[2].
Cc: linux-stable <stable@vger.kernel.org>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Olivier Sobrie <olivier@sobrie.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Linus Torvalds [Fri, 25 Jan 2013 19:57:28 +0000 (11:57 -0800)]
Linux 3.8-rc5
Linus Torvalds [Fri, 25 Jan 2013 18:55:21 +0000 (10:55 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"It turns out that we had two crc bugs when running fsx-linux in a
loop. Many thanks to Josef, Miao Xie, and Dave Sterba for nailing it
all down. Miao also has a new OOM fix in this v2 pull as well.
Ilya fixed a regression Liu Bo found in the balance ioctls for pausing
and resuming a running balance across drives.
Josef's orphan truncate patch fixes an obscure corruption we'd see
during xfstests.
Arne's patches address problems with subvolume quotas. If the user
destroys quota groups incorrectly the FS will refuse to mount.
The rest are smaller fixes and plugs for memory leaks."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (30 commits)
Btrfs: fix repeated delalloc work allocation
Btrfs: fix wrong max device number for single profile
Btrfs: fix missed transaction->aborted check
Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
Btrfs: put csums on the right ordered extent
Btrfs: use right range to find checksum for compressed extents
Btrfs: fix panic when recovering tree log
Btrfs: do not allow logged extents to be merged or removed
Btrfs: fix a regression in balance usage filter
Btrfs: prevent qgroup destroy when there are still relations
Btrfs: ignore orphan qgroup relations
Btrfs: reorder locks and sanity checks in btrfs_ioctl_defrag
Btrfs: fix unlock order in btrfs_ioctl_rm_dev
Btrfs: fix unlock order in btrfs_ioctl_resize
Btrfs: fix "mutually exclusive op is running" error code
Btrfs: bring back balance pause/resume logic
btrfs: update timestamps on truncate()
btrfs: fix btrfs_cont_expand() freeing IS_ERR em
Btrfs: fix a bug when llseek for delalloc bytes behind prealloc extents
Btrfs: fix off-by-one in lseek
...
Linus Torvalds [Fri, 25 Jan 2013 03:15:43 +0000 (19:15 -0800)]
Merge branch 'for-next' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two small cifs fixes"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
fs/cifs/cifs_dfs_ref.c: fix potential memory leakage
cifs: fix srcip_matches() for ipv6
Linus Torvalds [Fri, 25 Jan 2013 03:14:22 +0000 (19:14 -0800)]
Merge git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixlet from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Emulate dcbf
Linus Torvalds [Thu, 24 Jan 2013 20:44:57 +0000 (12:44 -0800)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"A number of fixes:
Patrik found a problem with preempt counting in the VFP assembly
functions which can cause the preempt count to be upset.
Nicolas fixed a problem with the parsing of the DT when it straddles a
1MB boundary.
Subhash Jadavani reported a problem with sparsemem and our highmem
support for cache maintanence for DMA areas, and TI found a bug in
their strongly ordered memory mapping type.
Also, three fixes by way of Will Deacon's tree from Dave Martin for
instruction compatibility and Marc Zyngier to fix hypervisor boot mode
issues."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7629/1: mm: Fix missing XN flag for for MT_MEMORY_SO
ARM: DMA: Fix struct page iterator in dma_cache_maint() to work with sparsemem
ARM: 7628/1: head.S: map one extra section for the ATAG/DTB area
ARM: 7627/1: Predicate preempt logic on PREEMP_COUNT not PREEMPT alone
ARM: virt: simplify __hyp_stub_install epilog
ARM: virt: boot secondary CPUs through the right entry point
ARM: virt: Avoid bx instruction for compatibility with <=ARMv4
Linus Torvalds [Thu, 24 Jan 2013 20:42:50 +0000 (12:42 -0800)]
Merge tag 'fixes-for-linus2' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
Linus Torvalds [Thu, 24 Jan 2013 18:19:13 +0000 (10:19 -0800)]
Merge tag 'pm+acpi-for-3.8-rc5' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- Two cpuidle initialization fixes from Konrad Rzeszutek Wilk.
- cpufreq regression fixes for AMD processors from Borislav Petkov,
Stefan Bader, and Matthew Garrett.
- ACPI cpufreq fix from Thomas Schlichter.
- cpufreq and devfreq fixes related to incorrect usage of operating
performance points (OPP) framework and RCU from Nishanth Menon.
- APEI workaround for incorrect BIOS information from Lans Zhang.
* tag 'pm+acpi-for-3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Add module aliases for acpi-cpufreq
ACPI: Check MSR valid bit before using P-state frequencies
PM / devfreq: exynos4_bus: honor RCU lock usage
PM / devfreq: add locking documentation for recommended_opp
cpufreq: cpufreq-cpu0: use RCU locks around usage of OPP
cpufreq: OMAP: use RCU locks around usage of OPP
ACPI, APEI: Fixup incorrect 64-bit access width firmware bug
ACPI / processor: Get power info before updating the C-states
powernow-k8: Add a kconfig dependency on acpi-cpufreq
ACPI / cpuidle: Fix NULL pointer issues when cpuidle is disabled
intel_idle: Don't register CPU notifier if we are not running.
Linus Torvalds [Thu, 24 Jan 2013 18:18:37 +0000 (10:18 -0800)]
Merge tag 'regmap-fix-3.8-rc4' of git://git./linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"One more oversight in the debugfs code was reported and fixed, plus a
documentation fix."
* tag 'regmap-fix-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix small typo in regmap_bulk_write comment
regmap: debugfs: Fix seeking from the cache
Linus Torvalds [Thu, 24 Jan 2013 18:17:49 +0000 (10:17 -0800)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes on slave dmanengine. There are trivial fixes in imx-dma,
tegra-dma & ioat driver"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: implement flags parameters for cyclic transfer
dmaengine: imx-dma: Disable use of hw_chain to fix sg_dma transfers.
ioat: Fix DMA memory sync direction correct flag
Linus Torvalds [Thu, 24 Jan 2013 18:17:03 +0000 (10:17 -0800)]
Merge branch 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux
Pill i2c fixes from Wolfram Sang:
"Here are a few, typical driver fixes for the I2C subsystem"
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c-designware: add missing MODULE_LICENSE
i2c: omap: fix draining irq handling
i2c: omap: errata i462: fix incorrect ack for arbitration lost interrupt
i2c: muxes: fix wrong use of sizeof(ptr)
i2c: sirf: register i2c_client from dt child-nodes in probe entry
i2c: mxs: Fix type of error code
i2c: mxs: Fix misuse init_completion
Miao Xie [Tue, 22 Jan 2013 10:49:00 +0000 (10:49 +0000)]
Btrfs: fix repeated delalloc work allocation
btrfs_start_delalloc_inodes() locks the delalloc_inodes list, fetches the
first inode, unlocks the list, triggers btrfs_alloc_delalloc_work/
btrfs_queue_worker for this inode, and then it locks the list, checks the
head of the list again. But because we don't delete the first inode that it
deals with before, it will fetch the same inode. As a result, this function
allocates a huge amount of btrfs_delalloc_work structures, and OOM happens.
Fix this problem by splice this delalloc list.
Reported-by: Alex Lyakas <alex.btrfs@zadarastorage.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Miao Xie [Wed, 16 Jan 2013 11:27:17 +0000 (11:27 +0000)]
Btrfs: fix wrong max device number for single profile
The max device number of single profile is 1, not 0 (0 means 'as many as
possible'). Fix it.
Cc: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Miao Xie [Tue, 15 Jan 2013 06:29:12 +0000 (06:29 +0000)]
Btrfs: fix missed transaction->aborted check
First, though the current transaction->aborted check can stop the commit early
and avoid unnecessary operations, it is too early, and some transaction handles
don't end, those handles may set transaction->aborted after the check.
Second, when we commit the transaction, we will wake up some worker threads to
flush the space cache and inode cache. Those threads also allocate some transaction
handles and may set transaction->aborted if some serious error happens.
So we need more check for ->aborted when committing the transaction. Fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Miao Xie [Tue, 15 Jan 2013 06:27:25 +0000 (06:27 +0000)]
Btrfs: Add ACCESS_ONCE() to transaction->abort accesses
We may access and update transaction->aborted on the different CPUs without
lock, so we need ACCESS_ONCE() wrapper to prevent the compiler from creating
unsolicited accesses and make sure we can get the right value.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Tue, 22 Jan 2013 20:43:09 +0000 (15:43 -0500)]
Btrfs: put csums on the right ordered extent
I noticed a WARN_ON going off when adding csums because we were going over
the amount of csum bytes that should have been allowed for an ordered
extent. This is a leftover from when we used to hold the csums privately
for direct io, but now we use the normal ordered sum stuff so we need to
make sure and check if we've moved on to another extent so that the csums
are added to the right extent. Without this we could end up with csums for
bytenrs that don't have extents to cover them yet. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Liu Bo [Sun, 6 Jan 2013 03:38:22 +0000 (03:38 +0000)]
Btrfs: use right range to find checksum for compressed extents
For compressed extents, the range of checksum is covered by disk length,
and the disk length is different with ram length, so we need to use disk
length instead to get us the right checksum.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Tue, 18 Dec 2012 16:39:19 +0000 (11:39 -0500)]
Btrfs: fix panic when recovering tree log
A user reported a BUG_ON(ret) that occured during tree log replay. Ret was
-EAGAIN, so what I think happened is that we removed an extent that covered
a bitmap entry and an extent entry. We remove the part from the bitmap and
return -EAGAIN and then search for the next piece we want to remove, which
happens to be an entire extent entry, so we just free the sucker and return.
The problem is ret is still set to -EAGAIN so we trip the BUG_ON(). The
user used btrfs-zero-log so I'm not 100% sure this is what happened so I've
added a WARN_ON() to catch the other possibility. Thanks,
Reported-by: Jan Steffens <jan.steffens@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Josef Bacik [Thu, 24 Jan 2013 17:02:07 +0000 (12:02 -0500)]
Btrfs: do not allow logged extents to be merged or removed
We drop the extent map tree lock while we're logging extents, so somebody
could come in and merge another extent into this one and screw up our
logging, or they could even remove us from the list which would keep us from
logging the extent or freeing our ref on it, so we need to make sure to not
clear LOGGING until after the extent is logged, and then we can merge it to
adjacent extents. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Olof Johansson [Thu, 24 Jan 2013 16:12:24 +0000 (08:12 -0800)]
Merge branch 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux into fixes
From Pawel Moll:
- makes the V2P-CA15_A7 (a.k.a. TC2) work with 3.8 kernels
- improves vexpress-sysreg.c behaviour on arm64 platforms
* 'vexpress/fixes' of git://git.linaro.org/people/pawelmoll/linux:
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
Olof Johansson [Thu, 24 Jan 2013 15:49:49 +0000 (07:49 -0800)]
Merge tag 'at91-fixes' of git://github.com/at91linux/linux-at91 into fixes
From Nicolas Ferre:
Here are fixes for AT91 that are mainly related to device tree.
One RM9200 setup option is the only C code change.
Some documentation changes can clarify the pinctrl use.
Then, some defconfig modifications are allowing the affected platforms
to boot.
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
Pawel Moll [Tue, 27 Nov 2012 16:48:50 +0000 (16:48 +0000)]
mfd: vexpress-sysreg: Don't skip initialization on probe
The vexpress-sysreg driver does not have to be initialized
early, when the platform doesn't require this. Unfortunately
in such case it wasn't initialized correctly - master site
lookup and config bridge registration were missing. Fixed now.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Pawel Moll [Thu, 24 Jan 2013 11:48:54 +0000 (11:48 +0000)]
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
As the kernel is able to cope with multiple clusters,
uncomment the A7 cores in the Device Tree for V2P-CA15_A7
tile, making all 5 cores available to the user.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Lorenzo Pieralisi [Tue, 22 Jan 2013 10:56:40 +0000 (10:56 +0000)]
ARM: vexpress: extend the MPIDR range used for pen release check
In ARM multi-cluster systems the MPIDR affinity level 0 cannot be used as a
single cpu identifier, affinity levels 1 and 2 must be taken into account as
well.
This patch extends the MPIDR usage to affinity levels 1 and 2 in versatile
secondary cores start up code in order to compare the passed pen_release
value with the full-blown affinity mask.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Mark Brown [Thu, 24 Jan 2013 11:04:16 +0000 (19:04 +0800)]
Merge remote-tracking branch 'regmap/fix/debugfs' into tmp
Olof Johansson [Thu, 24 Jan 2013 04:35:02 +0000 (20:35 -0800)]
Merge tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
This is yet another critical imxfb fixes held off by absence of FB
maintainer for some time.
* tag 'imx-fixes-3.8-3' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: imxfb: Do not crash on reboot
Olof Johansson [Thu, 24 Jan 2013 04:30:52 +0000 (20:30 -0800)]
Merge tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc5
- fix memory leak in mvebu/clk-cpu.c
- use devm_ to correct/simplify error paths in mvsdio
- add missing #interrupt-cells property in kirkwood
* tag 'mvebu_fixes_for_v3.8-rc5' of git://git.infradead.org/users/jcooper/linux:
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
Linus Torvalds [Thu, 24 Jan 2013 04:11:35 +0000 (20:11 -0800)]
Merge tag 'usb-3.8-rc4' of git://git./linux/kernel/git/gregkh/usb
Pull more USB fixes from Greg Kroah-Hartman:
"Here are some more USB fixes for the 3.8-rc4 tree.
Some gadget driver fixes, and finally resolved the ehci-mxc driver
build issues (it's just some code moving around and being deleted)."
* tag 'usb-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: EHCI: fix build error in ehci-mxc
USB: EHCI: add a name for the platform-private field
USB: EHCI: fix incorrect configuration test
USB: EHCI: Move definition of EHCI_STATS to ehci.h
USB: UHCI: fix IRQ race during initialization
usb: gadget: FunctionFS: Fix missing braces in parse_opts
usb: dwc3: gadget: fix ep->maxburst for ep0
ARM: i.MX clock: Change the connection-id for fsl-usb2-udc
usb: gadget: fsl_mxc_udc: replace MX35_IO_ADDRESS to ioremap
usb: gadget: fsl-mxc-udc: replace cpu_is_xxx() with platform_device_id
usb: musb: cppi_dma: drop '__init' annotation
Linus Torvalds [Thu, 24 Jan 2013 04:10:48 +0000 (20:10 -0800)]
Merge tag 'char-misc-3.8-rc4' of git://git./linux/kernel/git/gregkh/char-misc
Pull drivers/misc fix from Greg Kroah-Hartman:
"Here is a single revert for the ti-st misc driver, fixing problem that
was introduced in 3.7-rc1 that has been bothering people."
* tag 'char-misc-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "drivers/misc/ti-st: remove gpio handling"
Linus Torvalds [Thu, 24 Jan 2013 04:09:58 +0000 (20:09 -0800)]
Merge tag 'tty-3.8-rc4' of git://git./linux/kernel/git/gregkh/tty
Pull a TTY maintainer patch from Greg Kroah-Hartman:
"Just a MAINTAINERS update, now that Alan has left for a bit, I'll
continue to watch over the serial drivers."
* tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
MAINTAINERS: Someone needs to watch over the serial drivers
Linus Torvalds [Thu, 24 Jan 2013 04:07:12 +0000 (20:07 -0800)]
Merge branch 'v4l_for_linus' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- gspca: add needed delay for I2C traffic for sonixb/sonixj cameras
- gspca: add one missing Kinect USB ID
- usbvideo: some regression fixes
- omap3isp: fix some build issues
- videobuf2: fix video output handling
- exynos s5p/m5mols: a few regression fixes.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
[media] omap3isp: Don't include <plat/cpu.h>
[media] s5p-mfc: Fix interrupt error handling routine
[media] s5p-fimc: Fix return value of __fimc_md_create_flite_source_links()
[media] m5mols: Fix typo in get_fmt callback
[media] v4l: vb2: Set data_offset to 0 for single-plane output buffers
[media] [FOR,v3.8] omap3isp: Don't include deleted OMAP plat/ header files
[media] gspca_sonixj: Add a small delay after i2c_w1
[media] gspca_sonixb: Properly wait between i2c writes
[media] gspca_kinect: add Kinect for Windows USB id
Greg Kroah-Hartman [Wed, 23 Jan 2013 23:45:23 +0000 (15:45 -0800)]
MAINTAINERS: Someone needs to watch over the serial drivers
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Wed, 23 Jan 2013 21:31:15 +0000 (13:31 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"The asm-generic changeset has been ack'ed by Arnd."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up finit_module
asm-generic/dma-mapping-broken.h: Provide dma_alloc_attrs()/dma_free_attrs()
m68k: Provide dma_alloc_attrs()/dma_free_attrs()
Linus Torvalds [Wed, 23 Jan 2013 21:28:17 +0000 (13:28 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/cmarinas/linux-aarch64
Pull arm64 fixes from Catalin Marinas:
- ELF coredump fix (more registers dumped than what user space expects)
- SUBARCH name generation (s/aarch64/arm64/)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: makefile: fix uname munging when setting ARCH on native machine
arm64: elf: fix core dumping to match what glibc expects
John W. Linville [Wed, 23 Jan 2013 19:34:00 +0000 (14:34 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless into for-davem
Alan Stern [Wed, 23 Jan 2013 18:26:15 +0000 (13:26 -0500)]
USB: EHCI: fix build error in ehci-mxc
This patch (as1643b) fixes a build error in ehci-hcd when compiling for
ARM with allmodconfig:
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
drivers/usb/host/ehci-mxc.c:280:31: warning: 'ehci_mxc_driver' defined but not used [-Wunused-variable]
drivers/usb/host/ehci-hcd.c:1285:0: warning: "PLATFORM_DRIVER" redefined [enabled by default]
drivers/usb/host/ehci-hcd.c:1255:0: note: this is the location of the previous definition
The fix is to convert ehci-mxc over to the new "ehci-hcd is a library"
scheme so that it can coexist peacefully with the ehci-platform
driver. As part of the conversion the ehci_mxc_priv data structure,
which was allocated dynamically, is now placed where it belongs: in
the private area at the end of struct ehci_hcd.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>