Tom Rini [Sat, 1 Jun 2019 18:20:25 +0000 (14:20 -0400)]
configs: Migrate the various SPL_BOOT_xxx choices for PowerPC
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
Andy Shevchenko [Wed, 12 Jun 2019 12:35:24 +0000 (15:35 +0300)]
common: Fix a typo abnove -> above
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Simon Goldschmidt [Tue, 11 Jun 2019 20:18:51 +0000 (22:18 +0200)]
tools: add tools/spl_size_limit to ignore list
This tool has just been added but it seems I forgot to add it to
the ignore list. So to prevent the built binary being marked as
unversioned, add it to the ignore list.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Marek Vasut [Tue, 11 Jun 2019 02:51:15 +0000 (04:51 +0200)]
net: Convert CONFIG_TFTP_BLOCKSIZE to Kconfig
Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs,
headers and whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Tue, 11 Jun 2019 02:51:14 +0000 (04:51 +0200)]
net: Convert CONFIG_IP_DEFRAG to Kconfig
Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers
and whitelist. This patch is a follow-up on a patch by Christian
Gmeiner with the added config/header/whitelist updates.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Ramon Fried [Thu, 6 Jun 2019 18:35:05 +0000 (21:35 +0300)]
MAINTAINERS: change Ramon Fried email address
Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Tom Rini [Wed, 12 Jun 2019 19:28:34 +0000 (15:28 -0400)]
Merge tag 'u-boot-amlogic-
20190612' of git://git.denx.de/u-boot-amlogic
- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
Tom Rini [Wed, 12 Jun 2019 11:15:38 +0000 (07:15 -0400)]
Merge tag 'efi-2019-07-rc5' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc5
This pull request provides fixes for event services.
Maxime Jourdan [Tue, 4 Jun 2019 20:26:37 +0000 (22:26 +0200)]
pinctrl: meson-gxbb: add hdmi related pins
The GXBB pinctrl is missing pins related to HDMI, namely hot plug
detection (hpd) and I2C (sda + scl).
This fixes HDMI support for GXBB in u-boot.
Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Guillaume La Roque [Tue, 4 Jun 2019 11:53:08 +0000 (13:53 +0200)]
pinctrl: meson: g12a: add DS bank value
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Guillaume La Roque [Tue, 4 Jun 2019 11:53:07 +0000 (13:53 +0200)]
pinctrl: meson: add support of drive-strength-microamp
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Guillaume La Roque [Tue, 4 Jun 2019 11:53:06 +0000 (13:53 +0200)]
dm: pinctrl: Add driver-strength-microamp property
Add drive-strength-microamp property support to allow drive strength in uA
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 4 Jun 2019 09:04:54 +0000 (11:04 +0200)]
pinctrl: meson-axg: add support for getting pinmux status
In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the AXG specific function to get
the current function from registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 4 Jun 2019 09:04:53 +0000 (11:04 +0200)]
pinctrl: meson-gx: add support for getting pinmux status
In order to support the "pinmux status" command, use the common functions
to get the pins count and names, and add the GX specific function to get
the current function from registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Neil Armstrong [Tue, 4 Jun 2019 09:04:52 +0000 (11:04 +0200)]
pinctrl: meson: add common function to get pins name
In order to support the "pinmux status" command, add common function
to get pins count and pin name.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 4 Jun 2019 09:04:51 +0000 (11:04 +0200)]
pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
The GPIO_TEST_N was in the wrong pmx group table, move it back with the AO
groups, GPIODV_18 was missing, add it back, and finally the GPIOCLK_*
group names were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tom Rini [Tue, 11 Jun 2019 21:22:22 +0000 (17:22 -0400)]
Merge tag 'u-boot-stm32-
20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
Tom Rini [Tue, 11 Jun 2019 17:41:24 +0000 (13:41 -0400)]
Merge tag 'u-boot-imx-
20190612' of git://git.denx.de/u-boot-imx
u-boot-imx-
20190612
--------------------
- Board fixes:
- imx6logic
- wandboard
- mx6sabre boots again
- imx8qm_mek
- pico-* boards
- Toradex apalis / colibri
- engicam imx6 (environment)
- KP MX53
- opos6ul
- Switch to DM:
- vining2000
- dh MX6
- Toradex colibri i.MX7
- Novena
- Security : fix CSF size for HAB
- Other:
- imx: fix building for i.mx8 without spl
- pcie and switch to DM
mx6sabreauto: Enable SPL SDP support
Heinrich Schuchardt [Wed, 27 Feb 2019 19:05:43 +0000 (20:05 +0100)]
configs: tinker-rk3288 disable CONFIG_SPL_I2C_SUPPORT
The SPL for the Tinker Board has to fit into 32 KiB. Currently this limit
is exceeded.
CONFIG_SPL_I2C_SUPPORT is not needed to move to main U-Boot. So let's
disable it.
Suggested-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fabio Estevam [Sat, 8 Jun 2019 17:56:44 +0000 (14:56 -0300)]
spl: imx6: Provide a SPL_SIZE_LIMIT default
As explained in include/configs/imx6_spl.h. the i.MX6 SPL
size limit is 68KB (4KB header + 64KB max size).
Provide such limit for all i.MX6 boards that use SPL
to detect SPL size overflow in build time.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Sjoerd Simons [Tue, 4 Jun 2019 19:56:28 +0000 (21:56 +0200)]
mx6sabreauto: Enable SPL SDP support
To allow loading u-boot over USB enable SDP support in the SPL.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sjoerd Simons [Tue, 4 Jun 2019 19:56:27 +0000 (21:56 +0200)]
mx6sabreauto: Remove CONFIG_SPL_DM to decrease the SPL size
The i.mx6 SPL binary cannot be bigger then 68K, while with the current
defconfig for sabreauto it's only about 56K as soon as USB support gets
added the size will overflows.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sjoerd Simons [Tue, 4 Jun 2019 13:49:58 +0000 (15:49 +0200)]
arm: dts: imx6qdl-u-boot: Alias usb0 to usbotg
All i.mx6 boards seems to have moved to DM_USB, however gadget support
for mx6 is still pre-DM as CI_UDC isn't converted yet. To make this work
the usb otg controller used for gadgets needs to be usb number 0.
Add an alias for this directly in the main u-boot mx6qdl dtsi so it
doesn't need to be done for each board separately.
This fixes regressions wrt. usb gadget functionality in several boards
that have gadget functions enabled in their config, but no usb0 alias in
their device-tree.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Sjoerd Simons [Tue, 4 Jun 2019 13:49:57 +0000 (15:49 +0200)]
mx6sabreauto: set SYS_MALLOC_F for video
Sabre Auto boards currently hang with:
```
U-Boot 2019.07-rc3-00057-gc41940c406 (Jun 03 2019 - 14:42:41 +0200)
CPU: Freescale i.MX6QP rev1.0 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C)Reset cause: WDOG
Model: Freescale i.MX6 Quad Plus SABRE Automotive Board
Board: MX6Q-Sabreauto revA
I2C: ready
DRAM: 2 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence
8ffe00b8 failed at call
1780e93b (err=-28)
```
Set SYS_MALLOC_F_LEN to reserve_video to work.
This is similar to the change Peng Fan did for mx6sabresd (
9002e735e717)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Sjoerd Simons [Tue, 4 Jun 2019 13:49:56 +0000 (15:49 +0200)]
mx6sabreauto: Select pinctrl driver
With the conversion to DM we should select the pinctrl driver.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Sat, 18 May 2019 16:18:45 +0000 (13:18 -0300)]
imx8mq_evk: Staticize when appropriate
Staticize 'spl_dram_init' and 'i2c_pad_info1' to fix the
following sparse warnings:
board/freescale/imx8mq_evk/spl.c:30:6: warning: symbol 'spl_dram_init' was not declared. Should it be static?
board/freescale/imx8mq_evk/spl.c:41:22: warning: symbol 'i2c_pad_info1' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Thu, 9 May 2019 08:33:55 +0000 (08:33 +0000)]
imx: define ARCH_MXC for i.MX8/8M/7ULP
Without this definition, fsl_esdhc will access reserved registers
on i.MX chips, so define ARCH_MXC to fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Thu, 9 May 2019 08:33:52 +0000 (08:33 +0000)]
imx: drop imx-regs.h
imx-regs.h under arch-imx has no user, drop it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Peng Fan [Fri, 26 Apr 2019 01:44:27 +0000 (01:44 +0000)]
imx8: cpu: get temperature when print cpu desc
Read the temperature when print cpu inforation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Lukasz Majewski [Tue, 23 Apr 2019 14:44:51 +0000 (16:44 +0200)]
pinctrl: imx: Define imx6_pinctrl_soc_info in .data section
This commit is necessary to be able to re-use the pinctrl code in early
SPL to properly configure pins.
The problem is that those "static" structures (without explicit
initialization) are placed in the SDRAM area, which corresponds to
u-boot proper (not even SPL).
Hence, when one wants to configure pins before relocation via DTS/DM,
the board hangs (imx6q SoC powered one) as only OCRAM area is available
(0x009xxxxx).
This commit prevents from this issue by moving the imx6_pinctrl_soc_info
structure to data section (from BSS).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Mon, 15 Apr 2019 05:18:33 +0000 (05:18 +0000)]
net: fec_mxc: not access reserved register on i.MX8
We should not access reserved register on i.MX8, otherwise met SERROR
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Fri, 17 May 2019 20:25:28 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM Serial
Enable DM Serial support on iMX6SX VINING|2000.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:27 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM PCI
Enable DM PCI support on iMX6SX VINING|2000.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:26 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM GPIO
Enable DM GPIO support on iMX6SX VINING|2000 and fix up
board code where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:25 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM USB
Enable DM USB support on iMX6SX VINING|2000.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:24 +0000 (22:25 +0200)]
ARM: imx: vining2000: Convert MMC and block to DM
Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:23 +0000 (22:25 +0200)]
ARM: imx: vining2000: Enable DM pin control
Enable DM pin control support on iMX6SX VINING|2000.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:22 +0000 (22:25 +0200)]
ARM: dts: imx: vining2000: Import VINING|2000 DT from Linux
Import iMX6SX VINING|2000 device tree from Linux 5.1.1
b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 20:25:21 +0000 (22:25 +0200)]
ARM: imx: Rename VINING|2000
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Christoph Fritz [Fri, 17 May 2019 19:19:31 +0000 (21:19 +0200)]
mx6sx: vining2000: pinmux usdhc4 reset
This patch configures pinmux for pin usdhc4 reset.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Fabio Estevam [Fri, 10 May 2019 12:23:53 +0000 (09:23 -0300)]
MAINTAINERS: Add imx dts files to i.MX maintainers list
Add imx dts files to the MAINTAINERS file list, so that i.MX
devicetree related patches can be properly sent to the i.MX folks.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Fri, 17 May 2019 19:56:40 +0000 (21:56 +0200)]
serial: mxc: Add iMX6SX compatible string
Add compatible string for iMX6SX.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 18:32:19 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM PCI
Enable DM PCI support on iMX6Q Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Sun, 9 Jun 2019 01:50:55 +0000 (03:50 +0200)]
pci: imx: Add DM and DT support
Add DM support and support for probing the iMX PCI driver from DT.
The legacy non-DM support is retained, however shall be removed once
DM PCI is the only option remaining.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 9 Jun 2019 01:50:54 +0000 (03:50 +0200)]
pci: imx: Pass driver private data around
Pass the driver private data around the driver as much as possible, instead
of having it as a static global variable. This is done in preparation for
the DM conversion, no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 9 Jun 2019 01:50:53 +0000 (03:50 +0200)]
pci: imx: Fix potential 64bit memory access clamping
The driver limits the config space base to 32bit, however it can be
64bit on 64bit iMX hardware too. Remove that limitation. This patch
has no impact on the iMX6, which is the only SoC currently supported
by this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 9 Jun 2019 01:50:52 +0000 (03:50 +0200)]
pci: imx: Factor out hard-coded register base addresses
Pull out hard-coded register base addresses into driver private
structure in preparation for DM conversion. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Marek Vasut [Sun, 9 Jun 2019 01:50:51 +0000 (03:50 +0200)]
ARM: imx: Call imx_pcie_remove() only for non-DM PCI driver
The DM iMX PCI driver has DM_FLAG_OS_PREPARE set and will call
imx_pcie_remove() from the .remove callback. Do not call it from
the architecture code again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fabio Estevam [Tue, 21 May 2019 13:37:54 +0000 (10:37 -0300)]
mx6sabresd: Remove U-Boot proper mmc initialization
After the conversion to DM there is no need to have mmc initialization
code inside U-Boot proper.
Remove the unneeded code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Tue, 21 May 2019 13:37:53 +0000 (10:37 -0300)]
mx6sabresd: Select pinctrl driver
With the conversion to DM we should select the pinctrl driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Tue, 21 May 2019 13:37:52 +0000 (10:37 -0300)]
mx6sabresd: Remove CONFIG_SPL_DM to decrease the SPL size
Currently the mx6qsabresd board does not boot:
U-Boot SPL 2019.07-rc2 (May 16 2019 - 14:28:55 -0300)
Trying to boot from MMC1
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The reason for the boot failure is that that the SPL
size got greater than the 68KB limit (4KB header + 64KB max
size) as explained in include/configs/imx6_spl.h.
Remove the CONFIG_SPL_DM option, so that the SPL binary could
fit into the allowed size and the board can boot again.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Wed, 8 May 2019 12:02:08 +0000 (09:02 -0300)]
imx8qxp_mek: Remove unneeded config options settings
Remove such unneeded custom config options because the
provided default values are good enough.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fabio Estevam [Wed, 8 May 2019 12:02:07 +0000 (09:02 -0300)]
imx8qm_mek: Remove unneeded config options settings
Remove such unneeded custom config options because the
provided default values are good enough.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Parthiban Nallathambi [Wed, 10 Apr 2019 14:35:32 +0000 (16:35 +0200)]
imx: Extend PCL063 support for phyCORE-i.MX6ULL SOM
Extend PHYTEC phyBOARD-i.MX6UL for phyCORE-i.MX6UL SoM (PCL063)
with eMMC on SoM.
CPU: Freescale i.MX6ULL rev1.0 792 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 38C
Reset cause: POR
Model: Phytec phyBOARD-i.MX6ULL-Segin SBC
Board: PHYTEC phyCORE-i.MX6ULL
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
In: serial@
02020000
Out: serial@
02020000
Err: serial@
02020000
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- eMMC
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Parthiban Nallathambi <parthitce@gmail.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:43 +0000 (13:00 +0300)]
apalis-tk1: use UUID for rootfs
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:42 +0000 (13:00 +0300)]
apalis_imx6: use UUID for rootfs
1. Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
2. Fix legacy USB command (both sdboot and usbboot can be used now).
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:41 +0000 (13:00 +0300)]
colibri_vf: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:40 +0000 (13:00 +0300)]
colibri-imx6ull: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Igor Opaniuk [Wed, 29 May 2019 10:00:39 +0000 (13:00 +0300)]
colibri_imx7: use UUID for rootfs
Replace usage of "/dev/mmcblk*p*" with a proper UUID of rootfs
partition. This fixes the issue, when MMC controllers are probed in
a different order in U-boot and Linux kernel.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:20 +0000 (19:00 +0300)]
board: toradex: add apalis imx8qm 4gb wb it v1.0b module support
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:19 +0000 (19:00 +0300)]
imx8: fuse: fix fuse driver
This fixes the i.MX 8 fuse driver to actually build for i.MX 8QM as
well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:18 +0000 (19:00 +0300)]
imx8qm: fix cpu frequency reporting
CPU frequency reporting failed with the following error message being
printed:
sc_pm_get_clock_rate: resource:507 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QM RevB A53 at 0 MHz
Fix this by differentiating between the A35 as found on the i.MX 8QXP
and the A53 as found on the i.MX 8QM SoCs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:17 +0000 (19:00 +0300)]
clk: imx8qm: fix usdhc2 clocks
Trying to bring up uSDHC2 the following error message was observed:
MMC: imx8_clk_set_rate(Invalid clk ID #60)
imx8_clk_set_rate(Invalid clk ID #60)
usdhc@
5b030000 - probe failed: -22
This commit fixes this by properly setting resp. clocks.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:16 +0000 (19:00 +0300)]
arm: dts: imx8qm: add support for i2c0, i2c1, i2c2, i2c3 and i2c4
Add support for i2c0, i2c1, i2c2, i2c3 and i2c4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Marcel Ziswiler [Fri, 31 May 2019 16:00:15 +0000 (19:00 +0300)]
arm: dts: imx8qm: add lpuart1, lpuart2, lpuart3, lpuart4
Add support for lpuart1, lpuart2, lpuart3 and lpuart4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Fabio Estevam [Fri, 26 Apr 2019 16:56:34 +0000 (13:56 -0300)]
pico-imx6ul: MAINTAINERS: Add pico-dwarf entry
pico-dwarf-imx6ul_defconfig does not have an entry in MAINTAINERS file,
so add it to avoid a build warning.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Fri, 26 Apr 2019 16:56:33 +0000 (13:56 -0300)]
pico-imx6ul: MAINTAINERS: Unify all board entries
It is easier to consolidate all boards into a single entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Fri, 26 Apr 2019 16:56:32 +0000 (13:56 -0300)]
pico-imx7d: MAINTAINERS: Unify all board entries
It is easier to consolidate all boards into a single entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Igor Opaniuk [Fri, 31 May 2019 10:19:35 +0000 (13:19 +0300)]
colibri_imx7: fastboot support
Enable fastboot support (including "fastboot oem" subset of commands).
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Marek Vasut [Fri, 17 May 2019 18:32:20 +0000 (20:32 +0200)]
ARM: imx: novena: Convert to DM VIDEO
Enable DM Video support on iMX6Q Novena and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:18 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM USB
Enable DM USB support on iMX6Q Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:17 +0000 (20:32 +0200)]
ARM: imx: novena: Convert block devices to DM
Enable DM block, DM MMC and DM SATA support on iMX6Q Novena
convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:16 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM GPIO
Enable DM GPIO support on iMX6Q Novena and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:15 +0000 (20:32 +0200)]
ARM: imx: novena: Enable DM pin control
Enable DM pin control support on iMX6Q Novena.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Marek Vasut [Fri, 17 May 2019 18:32:14 +0000 (20:32 +0200)]
ARM: dts: imx: novena: Import Novena DT from Linux
Import iMX6Q Novena device tree from Linux 5.1-rc7
37624b58542f .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Jun Nie [Wed, 8 May 2019 06:38:36 +0000 (14:38 +0800)]
pico-imx7d: enable boot without PMIC
If PMIC is not probed successfully, it is still OK to boot
with default configuration although power is not optimized.
Default voltage of SW1A/SW1B is 1.1V/1.0V for PC32PF3000A1EP
on pico according to table 42 of spec of PF3000 ver 9.0.
Default mode of SW1A/SW1B is APS as expected(table 47).
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:35 +0000 (14:38 +0800)]
pico-imx7d: README: Add BL33 usage case
Add Documentation of BL33 usage case. U-boot is in
non-secure world in this case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:34 +0000 (14:38 +0800)]
pico-imx7d: Add bl33 config
Add default configuration to run u-boot as BL33 in the boot flow case
of ATF(ARM Trusted Firmware) -> OPTEE -> U-boot.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Jun Nie [Wed, 8 May 2019 06:38:33 +0000 (14:38 +0800)]
pico-imx7d: Add boot option for verified boot
Add boot option to boot from fitimage to support verified boot.
The boot script plain text file should be packed into fit blob as
image with name of bootscr.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:32 +0000 (14:38 +0800)]
pico-imx7d: Reserve region of memory to OPTEE
Subtracts CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size so that
the OPTEE memory is not override during u-boot relocation.
Note the OPTEE live in the end part of DRAM and OPTEE boot process will
itself subtract the DRAM region it lives in from the memory map passed
to Linux.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Jun Nie [Wed, 8 May 2019 06:38:31 +0000 (14:38 +0800)]
pico-imx7d: Correct uart clock root
Correct uart clock root ID. Incorrect ID may result the
clock is gated because rate value 0 is returned in
imx_get_uartclk()
The ID can be ignored if CONFIG_SKIP_LOWLEVEL_INIT is not enabled
because init_clk_uart() will enable all uart clocks in that case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:30 +0000 (14:38 +0800)]
imx: mx7: Skip secure init in arch_cpu_init
Skip secure related initialization in arch_cpu_init if low level
init is skipped. Because these should be done in early stage
firmware, such as ARM trusted firmware.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Jun Nie [Wed, 8 May 2019 06:38:29 +0000 (14:38 +0800)]
mx7_common: Share configs to skip low level init
Share configs in mx7 to skip low level init if we are in the case where
OPTEE is loaded already (maybe by ARM Trusted Firmware) and that most of
the low level initialization is already done and that we may/should skip
it doing them here.
Fix the definition detection with size detection to decide whether to skip
it.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Heiko Schocher [Sun, 26 May 2019 10:15:47 +0000 (12:15 +0200)]
spi: imx: work with cs greater 0
currently spi mxc driver can only handle cs 0.
Allow it to handle also cs > 0.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Sun, 26 May 2019 10:15:46 +0000 (12:15 +0200)]
spi: imx: remove doubled pointer from mxc_spi_probe
in mxc_spi_probe() plat and mxcs pointer are created:
struct mxc_spi_slave *plat = bus->platdata;
struct mxc_spi_slave *mxcs = dev_get_platdata(bus);
which have the same value. Remove plat pointer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Heiko Schocher [Tue, 28 May 2019 11:44:31 +0000 (13:44 +0200)]
arm, imx, Makefile: fix u-boot-dtb.imx build in CONFIG_MULTI_DTB_FIT case
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
Ezequiel Garcia [Sat, 25 May 2019 22:19:41 +0000 (19:19 -0300)]
wandboard: Rework Makefile to prevent spl.o from being built
The spl.c source was entirely conditioned by CONFIG_SPL_BUILD.
Change this moving CONFIG_SPL_BUILD to be used in the Makefile,
which is slightly cleaner and more readable.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Marek Vasut [Fri, 17 May 2019 14:58:54 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert SPI support to DM
Enable DM SPI and SF support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:53 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert USB support to DM
Enable DM USB host support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:52 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert SATA support to DM
Enable DM SATA support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:51 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Convert SD/MMC support to DM
Enable DM block and DM MMC support on DHCOM iMX6 PDK2.
Convert board code to match the DM support.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:50 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Enable DM GPIO
Enable DM GPIO support on DHCOM iMX6 PDK2 and fix up board code
where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:49 +0000 (16:58 +0200)]
ARM: imx: dh-imx6: Enable DM pin control
Enable DM pin control support on DHCOM iMX6 PDK2.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:48 +0000 (16:58 +0200)]
ARM: dts: imx: dh-imx6: Fix SPI CS polarity on DHCOM iMX6 PDK2
The SPI nCS signal is active low, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Marek Vasut [Fri, 17 May 2019 14:58:47 +0000 (16:58 +0200)]
ARM: dts: imx: dh-imx6: Import DHCOM iMX6 PDK2 DTs from Linux
Import DHCOM iMX6 PDK2 device tree from Linux 5.1.1
b724e9356404 .
Enable DT control in full U-Boot .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Stefano Babic <sbabic@denx.de>
Breno Matheus Lima [Tue, 4 Jun 2019 02:54:44 +0000 (02:54 +0000)]
Revert "drivers/crypto/fsl: assign job-rings to non-TrustZone"
Commit
22191ac35344 ("drivers/crypto/fsl: assign job-rings to
non-TrustZone") breaks HABv4 encrypted boot support in the
following i.MX devices:
- i.MX6UL
- i.MX7S
- i.MX7D
- i.MX7ULP
For preparing a HABv4 encrypted boot image it's necessary to
encapsulate the generated DEK in a blob. In devices listed
above the blob generation function takes into consideration
the Job Ring TrustZone ownership configuration (JROWN_NS)
and can be only decapsulated by the same configuration.
The ROM code expects DEK blobs encapsulated by the Secure World
environments which commonly have JROWN_NS = 0.
As U-Boot is running in Secure World we must have JROWN_NS = 0
so the blobs generated by dek_blob tool can be decapsulated
by the ROM code.
Job-rings assignment is now handled in OP-TEE OS, this commit can
be safely reverted.
https://github.com/OP-TEE/optee_os/pull/2986
This reverts commit
22191ac353445ad8fafc5a78aefcd94e78963041.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Lukasz Majewski [Wed, 8 May 2019 14:26:23 +0000 (16:26 +0200)]
config: Update KP's imx53 HSC config to pass key pressed information
The information about pressed key is relevant in performing correct
update and recovery scenarios via USB pendrive.
This commit modifies envs to provide it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Lukasz Majewski [Wed, 8 May 2019 14:26:22 +0000 (16:26 +0200)]
config: Update KP's imx53 HSC config to support SWUpdate
This commit updates envs responsible for using USB pendrive as a
SWUpdate based tool for recovery and update.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Fabio Estevam [Fri, 3 May 2019 17:05:04 +0000 (14:05 -0300)]
imx: Use a convenient default value for SYS_MALLOC_F_LEN
Commit
3a7c45f6a772 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.
As explained by Lukas Auer:
"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x400) leaves U-Boot with not enough memory to
do this, causing it to hang."
Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.
Reported-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Sébastien Szymanski [Tue, 14 May 2019 11:46:20 +0000 (13:46 +0200)]
opos6uldev: don't call enable_lcdif_clock
The mxsfb driver already calls enable_lcdif_clock.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>