Frieder Schrempf [Tue, 15 Nov 2022 18:10:00 +0000 (19:10 +0100)]
spi: spi-imx: Fix spi_bus_clk if requested clock is higher than input clock
In case the requested bus clock is higher than the input clock, the correct
dividers (pre = 0, post = 0) are returned from mx51_ecspi_clkdiv(), but
*fres is left uninitialized and therefore contains an arbitrary value.
This causes trouble for the recently introduced PIO polling feature as the
value in spi_imx->spi_bus_clk is used there to calculate for which
transfers to enable PIO polling.
Fix this by setting *fres even if no clock dividers are in use.
This issue was observed on Kontron BL i.MX8MM with an SPI peripheral clock set
to 50 MHz by default and a requested SPI bus clock of 80 MHz for the SPI NOR
flash.
With the fix applied the debug message from mx51_ecspi_clkdiv() now prints the
following:
spi_imx
30820000.spi: mx51_ecspi_clkdiv: fin:
50000000, fspi:
50000000,
post: 0, pre: 0
Fixes:
6fd8b8503a0d ("spi: spi-imx: Fix out-of-order CS/SCLK operation at low speeds")
Fixes:
07e759387788 ("spi: spi-imx: add PIO polling support")
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Jander <david@protonic.nl>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221115181002.2068270-1-frieder@fris.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhichao Liu [Thu, 10 Nov 2022 07:28:39 +0000 (15:28 +0800)]
spi: mediatek: Fix DEVAPC Violation at KO Remove
A DEVAPC violation occurs when removing the module
due to accessing HW registers without base clock.
To fix this bug, the correct method is:
1. Call the runtime resume function to enable the
clock;
2. Operate the registers to reset the HW;
3. Turn off the clocks and disable the device
RPM mechanism.
Signed-off-by: Zhichao Liu <zhichao.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221110072839.30961-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vitaly Rodionov [Fri, 4 Nov 2022 10:06:37 +0000 (10:06 +0000)]
spi: amd: Fix SPI_SPD7 value
According to data sheet SPI_SPD7 should be set to 7.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221104100637.13376-1-vitalyr@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sean Nyekjaer [Thu, 3 Nov 2022 08:00:42 +0000 (09:00 +0100)]
spi: stm32: fix stm32_spi_prepare_mbr() that halves spi clk for every run
When this driver is used with a driver that uses preallocated spi_transfer
structs. The speed_hz is halved by every run. This results in:
spi_stm32
44004000.spi: SPI transfer setup failed
ads7846 spi0.0: SPI transfer failed: -22
Example when running with DIV_ROUND_UP():
- First run; speed_hz = 1000000, spi->clk_rate
125000000
div 125 -> mbrdiv = 7, cur_speed = 976562
- Second run; speed_hz = 976562
div 128,00007 (roundup to 129) -> mbrdiv = 8, cur_speed = 488281
- Third run; speed_hz = 488281
div 256,
000131072067109 (roundup to 257) and then -EINVAL is returned.
Use DIV_ROUND_CLOSEST to allow to round down and allow us to keep the
set speed.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20221103080043.3033414-1-sean@geanix.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Wed, 2 Nov 2022 08:46:01 +0000 (09:46 +0100)]
spi: meson-spicc: fix do_div build error on non-arm64
This fixes :
error: passing argument 1 of '__div64_32' from incompatible pointer type
By passing an uint64_t as first variable to do_div().
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
04694e50020b ("spi: meson-spicc: move wait completion in driver to take bursts delay in account")
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221027-b4-spicc-burst-delay-fix-v2-0-8cc2bab3417a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mika Westerberg [Tue, 25 Oct 2022 06:28:00 +0000 (09:28 +0300)]
spi: intel: Use correct mask for flash and protected regions
The flash and protected region mask is actually 0x7fff (30:16 and 14:0)
and not 0x3fff so fix this accordingly. While there use GENMASK() instead.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221025062800.22357-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
zhichao.liu [Fri, 21 Oct 2022 09:16:53 +0000 (17:16 +0800)]
spi: mediatek: Fix package division error
Commit
7e963fb2a33ce ("spi: mediatek: add ipm design support
for MT7986") makes a mistake on package dividing operation
(one change is missing), need to fix it.
Background:
Ipm design is expanding the HW capability of dma (adjust package
length from 1KB to 64KB), and using "dev_comp->ipm_support" flag
to indicate it.
Issue description:
Ipm support patch (said above) is missing to handle remainder at
package dividing operation.
One case, a transmission length is 65KB, is will divide to 1K
(package length) * 65(package loop) in non-ipm desgin case, and
will divide to 64K(package length) * 1(package loop) + 1K(remainder)
in ipm design case. And the 1K remainder will be lost with the
current SW flow, and the transmission will be failure.
So, it should be fixed.
Solution:
Add "ipm_design" flag in function "mtk_spi_get_mult_delta()" to
indicate HW capability, and modify the parameters corespondingly.
fixes:
7e963fb2a33ce ("spi: mediatek: add ipm design support for MT7986")
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20221021091653.18297-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jon Hunter [Wed, 26 Oct 2022 15:56:33 +0000 (16:56 +0100)]
spi: tegra210-quad: Don't initialise DMA if not supported
The following error messages are observed on boot for Tegra234 ...
ERR KERN tegra-qspi 3270000.spi: cannot use DMA: -19
ERR KERN tegra-qspi 3270000.spi: falling back to PIO
Tegra234 does not support DMA for the QSPI and so initialising the DMA
is expected to fail. The above error messages are misleading for devices
that don't support DMA and so fix this by skipping the DMA
initialisation for devices that don't support DMA.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221026155633.141792-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jay Fang [Fri, 28 Oct 2022 02:37:39 +0000 (10:37 +0800)]
MAINTAINERS: Update HiSilicon SFC Driver maintainer
Add Jay Fang as the maintainer of the HiSilicon SFC Driver, replacing
John Garry.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Acked-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20221028023739.4113998-1-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Wed, 26 Oct 2022 07:58:28 +0000 (09:58 +0200)]
spi: meson-spicc: move wait completion in driver to take bursts delay in account
Some delay occurs between each bursts, thus the default delay is wrong
and a timeout will occur with big enough transfers.
The solution is to handle the timeout management in the driver and
add some delay for each bursts in the timeout calculation.
Reported-by: Da Xue <da@libre.computer>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221026-spicc-burst-delay-v1-0-1be5ffb7051a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Marek Vasut [Tue, 18 Oct 2022 18:35:13 +0000 (20:35 +0200)]
spi: stm32: Print summary 'callbacks suppressed' message
The original fix "spi: stm32: Rate-limit the 'Communication suspended' message"
still leads to "stm32h7_spi_irq_thread: 1696 callbacks suppressed" spew in the
kernel log. Since this 'Communication suspended' message is a debug print, add
RATELIMIT_MSG_ON_RELEASE flag to inhibit the "callbacks suspended" part during
normal operation and only print summary at the end.
Fixes:
ea8be08cc9358 ("spi: stm32: Rate-limit the 'Communication suspended' message")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20221018183513.206706-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Cédric Le Goater [Sun, 16 Oct 2022 15:57:22 +0000 (17:57 +0200)]
spi: aspeed: Fix window offset of CE1
The offset value of the mapping window in the kernel structure is
calculated using the value of the previous window offset. This doesn't
reflect how the HW is configured and can lead to erroneous setting of
the second flash device (CE1).
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Fixes:
e3228ed92893 ("spi: spi-mem: Convert Aspeed SMC driver to spi-mem")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20221016155722.3520802-1-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Robert Marko [Thu, 6 Oct 2022 19:48:19 +0000 (21:48 +0200)]
spi: qup: support using GPIO as chip select line
Most of the device with QUP SPI adapter are actually using GPIO-s for
chip select.
However, this stopped working after ("spi: Retire legacy GPIO handling")
as it introduced a check on ->use_gpio_descriptors flag and since spi-qup
driver does not set the flag it meant that all of boards using GPIO-s and
with QUP adapter SPI devices stopped working.
So, to enable using GPIO-s again set ->use_gpio_descriptors to true and
populate ->max_native_cs.
Fixes:
f48dc6b96649 ("spi: Retire legacy GPIO handling")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: luka.perkov@sartura.hr
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20221006194819.1536932-1-robert.marko@sartura.hr
Signed-off-by: Mark Brown <broonie@kernel.org>
Mauro Lima [Wed, 12 Oct 2022 15:21:35 +0000 (12:21 -0300)]
spi: intel: Fix the offset to get the 64K erase opcode
According to documentation, the 64K erase opcode is located in VSCC
range [16:23] instead of [8:15].
Use the proper value to shift the mask over the correct range.
Signed-off-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20221012152135.28353-1-mauro.lima@eclypsium.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chin-Ting Kuo [Wed, 5 Oct 2022 08:32:09 +0000 (16:32 +0800)]
spi: aspeed: Fix typo in mode_bits field for AST2600 platform
Both quad SPI TX and RX modes can be supported on AST2600.
Correct typo in mode_bits field in both ast2600_fmc_data
and ast2600_spi_data structs.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20221005083209.222272-1-chin-ting_kuo@aspeedtech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe Leroy [Thu, 6 Oct 2022 05:35:12 +0000 (07:35 +0200)]
spi: mpc52xx: Replace NO_IRQ by 0
NO_IRQ is used to check the return of irq_of_parse_and_map().
On some architecture NO_IRQ is 0, on other architectures it is -1.
irq_of_parse_and_map() returns 0 on error, independent of NO_IRQ.
So use 0 instead of using NO_IRQ.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f41e09d710879726eacb98daedf16d0847303b9b.1665034444.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Jonathan Neuschäfer [Sat, 8 Oct 2022 15:14:59 +0000 (17:14 +0200)]
spi: spi-mem: Fix typo (of -> or)
In this instance, "or" makes more sense than "of", so I guess that "or"
was intended and "of" was a typo.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221008151459.1421406-1-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Bird, Tim [Mon, 3 Oct 2022 19:05:18 +0000 (19:05 +0000)]
spi: spi-gxp: fix typo in SPDX identifier line
Use '-' instead of '=' in identifier: "GPL-2.0-or-later"
Signed-off-by: Tim Bird <tim.bird@sony.com>
Link: https://lore.kernel.org/r/BYAPR13MB2503FF6412666D29FEAC8DCDFD5B9@BYAPR13MB2503.namprd13.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Krishna Yarlagadda [Sat, 1 Oct 2022 12:21:44 +0000 (17:51 +0530)]
spi: tegra210-quad: Fix combined sequence
Return value should be updated to zero in combined sequence routine
if transfer is completed successfully. Currently it holds timeout value
resulting in errors.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Link: https://lore.kernel.org/r/20221001122148.9158-1-kyarlagadda@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Marek Szyprowski [Fri, 30 Sep 2022 11:34:08 +0000 (13:34 +0200)]
spi: Ensure that sg_table won't be used after being freed
SPI code checks for non-zero sgt->orig_nents to determine if the buffer
has been DMA-mapped. Ensure that sg_table is really zeroed after free to
avoid potential NULL pointer dereference if the given SPI xfer object is
reused again without being DMA-mapped.
Fixes:
0c17ba73c08f ("spi: Fix cache corruption due to DMA/PIO overlap")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220930113408.19720-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Wed, 28 Sep 2022 14:52:56 +0000 (22:52 +0800)]
spi: spi-gxp: Use devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220928145256.1879256-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vincent Whitchurch [Tue, 27 Sep 2022 11:21:17 +0000 (13:21 +0200)]
spi: s3c64xx: Fix large transfers with DMA
The COUNT_VALUE in the PACKET_CNT register is 16-bit so the maximum
value is 65535. Asking the driver to transfer a larger size currently
leads to the DMA transfer timing out. Implement ->max_transfer_size()
and have the core split the transfer as needed.
Fixes:
230d42d422e7 ("spi: Add s3c64xx SPI Controller driver")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-5-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vincent Whitchurch [Tue, 27 Sep 2022 11:21:16 +0000 (13:21 +0200)]
spi: Split transfers larger than max size
A couple of drivers call spi_split_transfers_maxsize() from their
->prepare_message() callbacks to split transfers which are too big for
them to handle. Add support in the core to do this based on
->max_transfer_size() to avoid code duplication.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-4-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vincent Whitchurch [Tue, 27 Sep 2022 11:21:15 +0000 (13:21 +0200)]
spi: Fix cache corruption due to DMA/PIO overlap
The SPI core DMA mapping support performs cache management once for the
entire message and not between transfers, and this leads to cache
corruption if a message has two or more RX transfers with both
transfers targeting the same cache line, and the controller driver
decides to handle one using DMA and the other using PIO (for example,
because one is much larger than the other).
Fix it by syncing before/after the actual transfers. This also means
that we can skip the sync during the map/unmap of the message.
Fixes:
99adef310f68 ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-3-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vincent Whitchurch [Tue, 27 Sep 2022 11:21:14 +0000 (13:21 +0200)]
spi: Save current RX and TX DMA devices
Save the current RX and TX DMA devices to avoid having to duplicate the
logic to pick them, since we'll need access to them in some more
functions to fix a bug in the cache handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
zhichao.liu [Tue, 27 Sep 2022 08:32:48 +0000 (16:32 +0800)]
spi: mt65xx: Add dma max segment size declaration
Add spi dma max segment size declaration according to spi
hardware capability, instead of 64KB by system default
setting, to improve bus bandwidth for mass data transmission.
Signed-off-by: zhichao.liu <zhichao.liu@mediatek.com>
Link: https://lore.kernel.org/r/20220927083248.25404-1-zhichao.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sergio Paracuellos [Tue, 27 Sep 2022 03:19:29 +0000 (05:19 +0200)]
spi: migrate mt7621 text bindings to YAML
SoC MT7621 SPI bindings used text format, so migrate them to YAML.
There are some additions to the binding that were not in the original
file. This binding is used in MT7621 and MT7628a Ralink SoCs. To
properly match both dts nodes in tree we need to add to the schema
'clocks', 'clock-names' and 'reset-names'. Both 'clock-names' and
'reset-names' use 'spi' as string so maintain that as const in
the schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20220927031929.807070-1-sergio.paracuellos@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Mon, 26 Sep 2022 15:05:42 +0000 (17:05 +0200)]
spi: renesas,sh-msiof: Add r8a779g0 support
Document support for the Clock-Synchronized Serial Interface with FIFO
(MSIOF) in the Renesas R-Car V4H (R8A779G0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/a840ca8487cfd612fae2b20c98e93ae7c7f50ef4.1664204638.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Tue, 27 Sep 2022 10:33:19 +0000 (11:33 +0100)]
Fix PM disable depth imbalance in probe
Merge series from Zhang Qilong <zhangqilong3@huawei.com>:
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed when error returns to keep it
balanced. This series of patches fixed it in spi probe.
Yang Yingliang [Sat, 24 Sep 2022 13:18:54 +0000 (21:18 +0800)]
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-3-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Sat, 24 Sep 2022 13:18:53 +0000 (21:18 +0800)]
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-2-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Sat, 24 Sep 2022 13:18:52 +0000 (21:18 +0800)]
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
Use the devm_platform_get_and_ioremap_resource() helper instead of calling
platform_get_resource() and devm_ioremap_resource() separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220924131854.964923-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhang Qilong [Sat, 24 Sep 2022 12:13:09 +0000 (20:13 +0800)]
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:
db91841b58f9a ("spi/omap100k: Convert to runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-4-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhang Qilong [Sat, 24 Sep 2022 12:13:08 +0000 (20:13 +0800)]
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:
abf00907538e2 ("spi: dw: Add Baikal-T1 SPI Controller glue driver")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-3-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhang Qilong [Sat, 24 Sep 2022 12:13:07 +0000 (20:13 +0800)]
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:
73d5fe0462702 ("spi: cadence-quadspi: Remove spi_master_put() in probe failure path")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220924121310.78331-2-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Tue, 20 Sep 2022 14:22:16 +0000 (22:22 +0800)]
spi: s3c24xx: Switch to use devm_spi_alloc_master()
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220920142216.3002291-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Tue, 20 Sep 2022 11:46:15 +0000 (19:46 +0800)]
spi: xilinx: Switch to use devm_spi_alloc_master()
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20220920114615.2681751-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zhang Qilong [Thu, 22 Sep 2022 15:02:32 +0000 (23:02 +0800)]
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using the newest pm_runtime_resume_and_get is more appropriate
for simplifing code here.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20220922150232.115843-1-zhangqilong3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shang XiaoJing [Fri, 23 Sep 2022 10:16:32 +0000 (18:16 +0800)]
spi: aspeed: Remove redundant dev_err call
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220923101632.19170-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Torokhov [Fri, 23 Sep 2022 04:51:37 +0000 (21:51 -0700)]
spi: spi-mpc52xx: switch to using gpiod API
This switches the driver to use gpiod API instead of legacy gpio API,
which will brings us close to removing of_get_gpio() and other
OF-specific old APIs.
No functional change intended beyond some differences in error messages.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/Yy07WbMAG4bPgYNd@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Shang XiaoJing [Fri, 23 Sep 2022 10:17:26 +0000 (18:17 +0800)]
spi: cadence: Remove redundant dev_err call
devm_ioremap_resource() prints error message in itself. Remove the
dev_err call to avoid redundant error message.
Signed-off-by: Shang XiaoJing <shangxiaojing@huawei.com>
Link: https://lore.kernel.org/r/20220923101726.19420-1-shangxiaojing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Tue, 20 Sep 2022 11:44:48 +0000 (19:44 +0800)]
spi: xtensa-xtfpga: Switch to use devm_spi_alloc_master()
Switch to use devm_spi_alloc_master() to simpify error path.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20220920114448.2681053-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Wei Yongjun [Thu, 22 Sep 2022 04:08:07 +0000 (04:08 +0000)]
spi: meson-spicc: make symbol 'meson_spicc_pow2_clk_ops' static
The sparse tool complains as follows:
drivers/spi/spi-meson-spicc.c:570:22: warning:
symbol 'meson_spicc_pow2_clk_ops' was not declared. Should it be static?
This symbol is not used outside of spi-meson-spicc.c, so marks it static.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220922040807.1409540-1-weiyongjun@huaweicloud.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dan Carpenter [Wed, 21 Sep 2022 07:24:51 +0000 (10:24 +0300)]
spi: omap2-mcspi: Fix probe so driver works again
This condition was accidentally changed from "if (status < 0)" to
"if (status)". The platform_get_irq() function returns non-zero
positive values on success so, unfortunately, the driver could not be
used. Change the condition back to how it was.
Fixes:
f4ca8c88c2c7 ("spi: omap2-mcspi: Switch to use dev_err_probe() helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/Yyq8Q/kd301wVzg8@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Vincent Whitchurch [Fri, 16 Sep 2022 11:39:48 +0000 (13:39 +0200)]
spi: spi-loopback-test: Add test to trigger DMA/PIO mixing
Add a test where a small and a large transfer in a message hit the same
cache line. This test currently fails on spi-s3c64xx on in DMA mode
since it ends up mixing DMA and PIO without proper cache maintenance.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220916113951.228398-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Sat, 17 Sep 2022 12:25:04 +0000 (20:25 +0800)]
spi: omap2-mcspi: Switch to use dev_err_probe() helper
In the probe path, dev_err() can be replace with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220917122504.1896302-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 14 Sep 2022 15:33:33 +0000 (18:33 +0300)]
spi: mpc52xx: Replace of_gpio_count() by gpiod_count()
As a preparation to unexport of_gpio_named_count(), convert the
driver to use gpiod_count() instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220914153333.37701-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe Leroy [Thu, 18 Aug 2022 13:38:37 +0000 (15:38 +0200)]
spi: fsl_spi: Convert to transfer_one
Let the core handle all the chipselect bakery and replace
transfer_one_message() by transfer_one() and prepare_message().
At the time being, there is fsl_spi_cs_control() to handle
chipselects. That function handles both GPIO and non-GPIO
chipselects. The GPIO chipselects will now be handled by
the core directly, so only handle non-GPIO chipselects and
hook it to ->set_cs
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/753266abafe81722d86c3ddb8bac8ef1cb00fe8c.1660829841.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Jonker [Sun, 11 Sep 2022 17:58:39 +0000 (19:58 +0200)]
spi: rockchip: add power-domains property
The Rockchip rk3399 TRM mentions that pd_sdioaudio includes
sdio, spi, i2s and spdif. Add a power-domains property to
to match reality with spi-rockchip.yaml.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/12af4fe6-4d35-cb4a-f5f6-06e3aba990cb@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Jonker [Fri, 9 Sep 2022 22:02:07 +0000 (00:02 +0200)]
rockchip: add rockchip,rk3128-spi
Add rockchip,rk3128-spi compatible string.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/c05fb9a3-ebf7-adec-e8ca-bd137d157f50@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Sat, 10 Sep 2022 15:39:51 +0000 (16:39 +0100)]
spi: Merge tag 'v6.0-rc4' into spi-6.1
Linux 6.0-rc4 so we can test on BeagleBone again.
Andy Shevchenko [Thu, 8 Sep 2022 13:05:18 +0000 (16:05 +0300)]
spi: Group cs_change and cs_off flags together in struct spi_transfer
The commit
5e0531f6b90a ("spi: Add capability to perform some transfer
with chipselect off") added a new flag but squeezed it into a wrong
group of struct spi_transfer members (note that SPI_NBITS_* are macros
for easier interpretation of the tx_nbits and rx_nbits bitfields).
Group cs_change and cs_off flags together and their doc strings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220908130518.32186-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Neil Armstrong [Thu, 8 Sep 2022 12:18:03 +0000 (14:18 +0200)]
spi: meson-spicc: do not rely on busy flag in pow2 clk ops
Since [1], controller's busy flag isn't set anymore when the
__spi_transfer_message_noqueue() is used instead of the
__spi_pump_transfer_message() logic for spi_sync transfers.
Since the pow2 clock ops were limited to only be available when a
transfer is ongoing (between prepare_transfer_hardware and
unprepare_transfer_hardware callbacks), the only way to track this
down is to check for the controller cur_msg.
[1]
ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Fixes:
09992025dacd ("spi: meson-spicc: add local pow2 clock ops to preserve rate between messages")
Fixes:
ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Markus Schneider-Pargmann <msp@baylibre.com>
Link: https://lore.kernel.org/r/20220908121803.919943-1-narmstrong@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ye xingchen [Thu, 8 Sep 2022 01:04:29 +0000 (01:04 +0000)]
spi: lpspi: Remove the unneeded result variable
Return the value pm_runtime_force_suspend() directly instead of storing
it in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/20220908010429.342875-1-ye.xingchen@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe Leroy [Wed, 7 Sep 2022 14:11:25 +0000 (16:11 +0200)]
spi: Add capability to perform some transfer with chipselect off
Some components require a few clock cycles with chipselect off before
or/and after the data transfer done with CS on.
Typically IDT 801034 QUAD PCM CODEC datasheet states "Note *: CCLK
should have one cycle before CS goes low, and two cycles after
CS goes high".
The cycles "before" are implicitely provided by all previous activity
on the SPI bus. But the cycles "after" must be provided in order to
terminate the SPI transfer.
In order to use that kind of component, add a cs_off flag to
spi_transfer struct. When this flag is set, the transfer is performed
with chipselect off. This allows consummer to add a dummy transfer
at the end of the transfer list which is performed with chipselect
OFF, providing the required additional clock cycles.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/434165c46f06d802690208a11e7ea2500e8da4c7.1662558898.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Tue, 6 Sep 2022 16:10:48 +0000 (19:10 +0300)]
spi: nxp-fspi: Do not dereference fwnode in struct device
In order to make the underneath API easier to change in the future,
prevent users from dereferencing fwnode from struct device. Instead,
use the specific dev_fwnode() API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220906161048.39953-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Xu Qiang [Thu, 25 Aug 2022 06:53:24 +0000 (06:53 +0000)]
spi: qup: add missing clk_disable_unprepare on error in spi_qup_pm_resume_runtime()
Add the missing clk_disable_unprepare() before return
from spi_qup_pm_resume_runtime() in the error handling case.
Fixes:
dae1a7700b34 (“spi: qup: Handle clocks in pm_runtime suspend and resume”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
Link: https://lore.kernel.org/r/20220825065324.68446-2-xuqiang36@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Xu Qiang [Thu, 25 Aug 2022 06:53:23 +0000 (06:53 +0000)]
spi: qup: add missing clk_disable_unprepare on error in spi_qup_resume()
Add the missing clk_disable_unprepare() before return
from spi_qup_resume() in the error handling case.
Fixes:
64ff247a978f (“spi: Add Qualcomm QUP SPI controller support”)
Signed-off-by: Xu Qiang <xuqiang36@huawei.com>
Link: https://lore.kernel.org/r/20220825065324.68446-1-xuqiang36@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Sun, 4 Sep 2022 20:10:01 +0000 (13:10 -0700)]
Linux 6.0-rc4
Linus Torvalds [Sun, 4 Sep 2022 18:33:22 +0000 (11:33 -0700)]
Merge tag 'powerpc-6.0-4' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix handling of PCI domains in /proc on 32-bit systems using the
recently added support for numbering buses from zero for each domain.
- A fix and a revert for some changes to use READ/WRITE_ONCE() which
caused problems with KASAN enabled due to sanitisation calls being
introduced in low-level paths that can't cope with it.
- Fix build errors on 32-bit caused by the syscall table being
misaligned sometimes.
- Two fixes to get IBM Cell native machines booting again, which had
bit-rotted while my QS22 was temporarily out of action.
- Fix the papr_scm driver to not assume the order of events returned by
the hypervisor is stable, and a related compile fix.
Thanks to Aneesh Kumar K.V, Christophe Leroy, Jordan Niethe, Kajol Jain,
Masahiro Yamada, Nathan Chancellor, Pali Rohár, Vaibhav Jain, and Zhouyi
Zhou.
* tag 'powerpc-6.0-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register()
Revert "powerpc/irq: Don't open code irq_soft_mask helpers"
powerpc: Fix hard_irq_disable() with sanitizer
powerpc/rtas: Fix RTAS MSR[HV] handling for Cell
Revert "powerpc: Remove unused FW_FEATURE_NATIVE references"
powerpc: align syscall table for ppc32
powerpc/pci: Enable PCI domains in /proc when PCI bus numbers are not unique
powerpc/papr_scm: Fix nvdimm event mappings
Linus Torvalds [Sun, 4 Sep 2022 18:27:14 +0000 (11:27 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"s390:
- PCI interpretation compile fixes
RISC-V:
- fix unused variable warnings in vcpu_timer.c
- move extern sbi_ext declarations to a header
x86:
- check validity of argument to KVM_SET_MP_STATE
- use guest's global_ctrl to completely disable guest PEBS
- fix a memory leak on memory allocation failure
- mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
- fix build failure with Clang integrated assembler
- fix MSR interception
- always flush TLBs when enabling dirty logging"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: check validity of argument to KVM_SET_MP_STATE
perf/x86/core: Completely disable guest PEBS via guest's global_ctrl
KVM: x86: fix memoryleak in kvm_arch_vcpu_create()
KVM: x86: Mask off unsupported and unknown bits of IA32_ARCH_CAPABILITIES
KVM: s390: pci: Hook to access KVM lowlevel from VFIO
riscv: kvm: move extern sbi_ext declarations to a header
riscv: kvm: vcpu_timer: fix unused variable warnings
KVM: selftests: Fix ambiguous mov in KVM_ASM_SAFE()
KVM: selftests: Fix KVM_EXCEPTION_MAGIC build with Clang
KVM: VMX: Heed the 'msr' argument in msr_write_intercepted()
kvm: x86: mmu: Always flush TLBs when enabling dirty logging
kvm: x86: mmu: Drop the need_remote_flush() function
Nick Desaulniers [Thu, 1 Sep 2022 17:59:13 +0000 (10:59 -0700)]
Makefile.extrawarn: re-enable -Wformat for clang; take 2
-Wformat was recently re-enabled for builds with clang, then quickly
re-disabled, due to concerns stemming from the frequency of default
argument promotion related warning instances.
commit
258fafcd0683 ("Makefile.extrawarn: re-enable -Wformat for clang")
commit
21f9c8a13bb2 ("Revert "Makefile.extrawarn: re-enable -Wformat for clang"")
ISO WG14 has ratified N2562 to address default argument promotion
explicitly for printf, as part of the upcoming ISO C2X standard.
The behavior of clang was changed in clang-16 to not warn for the cited
cases in all language modes.
Add a version check, so that users of clang-16 now get the full effect
of -Wformat. For older clang versions, re-enable flags under the
-Wformat group that way users still get some useful checks related to
format strings, without noisy default argument promotion warnings. I
intentionally omitted -Wformat-y2k and -Wformat-security from being
re-enabled, which are also part of -Wformat in clang-16.
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Link: https://github.com/llvm/llvm-project/issues/57102
Link: https://www.open-std.org/jtc1/sc22/wg14/www/docs/n2562.pdf
Suggested-by: Justin Stitt <jstitt007@gmail.com>
Suggested-by: Nathan Chancellor <nathan@kernel.org>
Suggested-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 4 Sep 2022 04:27:27 +0000 (21:27 -0700)]
Merge tag 'gpio-fixes-for-v6.0-rc4' of git://git./linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A a set of fixes from the GPIO subsystem.
Most are small driver fixes except the realtek-otto driver patch which
is pretty big but addresses a significant flaw that can cause the CPU
to stay infinitely busy on uncleared ISR on some platforms.
Summary:
- MAINTAINERS update
- fix resource leaks in gpio-mockup and gpio-pxa
- add missing locking in gpio-pca953x
- use 32-bit I/O in gpio-realtek-otto
- make irq_chip structures immutable in four more drivers"
* tag 'gpio-fixes-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: ws16c48: Make irq_chip immutable
gpio: 104-idio-16: Make irq_chip immutable
gpio: 104-idi-48: Make irq_chip immutable
gpio: 104-dio-48e: Make irq_chip immutable
gpio: realtek-otto: switch to 32-bit I/O
gpio: pca953x: Add mutex_lock for regcache sync in PM
gpio: mockup: remove gpio debugfs when remove device
gpio: pxa: use devres for the clock struct
MAINTAINERS: rectify entry for XILINX GPIO DRIVER
William Breathitt Gray [Fri, 2 Sep 2022 17:45:26 +0000 (13:45 -0400)]
gpio: ws16c48: Make irq_chip immutable
Kernel warns about mutable irq_chips:
"not an immutable chip, please consider fixing!"
Make the struct irq_chip const, flag it as IRQCHIP_IMMUTABLE, add the
new helper functions, and call the appropriate gpiolib functions.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
William Breathitt Gray [Fri, 2 Sep 2022 17:45:25 +0000 (13:45 -0400)]
gpio: 104-idio-16: Make irq_chip immutable
Kernel warns about mutable irq_chips:
"not an immutable chip, please consider fixing!"
Make the struct irq_chip const, flag it as IRQCHIP_IMMUTABLE, add the
new helper functions, and call the appropriate gpiolib functions.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
William Breathitt Gray [Fri, 2 Sep 2022 17:45:24 +0000 (13:45 -0400)]
gpio: 104-idi-48: Make irq_chip immutable
Kernel warns about mutable irq_chips:
"not an immutable chip, please consider fixing!"
Make the struct irq_chip const, flag it as IRQCHIP_IMMUTABLE, add the
new helper functions, and call the appropriate gpiolib functions.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
William Breathitt Gray [Fri, 2 Sep 2022 17:45:23 +0000 (13:45 -0400)]
gpio: 104-dio-48e: Make irq_chip immutable
Kernel warns about mutable irq_chips:
"not an immutable chip, please consider fixing!"
Make the struct irq_chip const, flag it as IRQCHIP_IMMUTABLE, add the
new helper functions, and call the appropriate gpiolib functions.
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Linus Torvalds [Sat, 3 Sep 2022 20:23:11 +0000 (13:23 -0700)]
Merge tag 'for-linus-6.0-rc4-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- a minor fix for the Xen grant driver
- a small series fixing a recently introduced problem in the Xen
blkfront/blkback drivers with negotiation of feature usage
* tag 'for-linus-6.0-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
xen-blkfront: Cache feature_persistent value before advertisement
xen-blkfront: Advertise feature-persistent as user requested
xen-blkback: Advertise feature-persistent as user requested
Linus Torvalds [Sat, 3 Sep 2022 20:21:01 +0000 (13:21 -0700)]
Merge tag 'loongarch-fixes-6.0-2' of git://git./linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix several build errors or warnings, cleanup some code, and adjust
arch_do_signal_or_restart() to adapt generic entry"
* tag 'loongarch-fixes-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: mm: Remove the unneeded result variable
LoongArch: Fix arch_remove_memory() undefined build error
LoongArch: Fix section mismatch due to acpi_os_ioremap()
LoongArch: Improve dump_tlb() output messages
LoongArch: Adjust arch_do_signal_or_restart() to adapt generic entry
LoongArch: Avoid orphan input sections
Linus Torvalds [Sat, 3 Sep 2022 20:17:33 +0000 (13:17 -0700)]
Merge tag 's390-6.0-3' of git://git./linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Update defconfigs
- Fix linker script to align nospec tables correctly to avoid
potentially unbootable kernel with some config options
- Fix alignment check in prepare_hugepage_range() for 2GB hugepages to
avoid BUG in __unmap_hugepage_range() for unaligned mappings later
- Remove useless hugepage address alignment in hugetlb fault handling
* tag 's390-6.0-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/hugetlb: fix prepare_hugepage_range() check for 2 GB hugepages
s390: update defconfigs
s390: fix nospec table alignments
s390/mm: remove useless hugepage address alignment
Linus Torvalds [Sat, 3 Sep 2022 20:09:46 +0000 (13:09 -0700)]
Merge tag 'input-for-v6.0-rc3' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- GT1158 ID added to Goodix touchscreen driver
- Boeder Force Feedback Wheel USB added to iforce joystick driver
- fixup for iforce driver to avoid hangups
- fix autoloading of rk805-pwrkey driver.
* tag 'input-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: iforce - add support for Boeder Force Feedback Wheel
Input: iforce - wake up after clearing IFORCE_XMIT_RUNNING flag
Input: goodix - add compatible string for GT1158
MAINTAINERS: add include/dt-bindings/input to INPUT DRIVERS
Input: rk805-pwrkey - fix module autoloading
Input: goodix - add support for GT1158
dt-bindings: input: touchscreen: add compatible string for Goodix GT1158
Linus Torvalds [Sat, 3 Sep 2022 17:34:02 +0000 (10:34 -0700)]
Merge tag 'tty-6.0-rc4' of git://git./linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial/vt driver fixes for 6.0-rc4 that
resolve a number of reported issues:
- n_gsm fixups for previous changes that caused problems
- much-reported serdev crash fix that showed up in 6.0-rc1
- vt font selection bugfix
- kerneldoc build warning fixes
- other tiny serial core fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: n_gsm: avoid call of sleeping functions from atomic context
tty: n_gsm: replace kicktimer with delayed_work
tty: n_gsm: initialize more members at gsm_alloc_mux()
tty: n_gsm: add sanity check for gsm->receive in gsm_receive_buf()
tty: serial: atmel: Preserve previous USART mode if RS485 disabled
tty: serial: lpuart: disable flow control while waiting for the transmit engine to complete
tty: Fix lookahead_buf crash with serdev
serial: fsl_lpuart: RS485 RTS polariy is inverse
vt: Clear selection before changing the font
serial: document start_rx member at struct uart_ops
Linus Torvalds [Sat, 3 Sep 2022 17:32:17 +0000 (10:32 -0700)]
Merge tag 'staging-6.0-rc4' of git://git./linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are three small staging driver fixes for 6.0-rc4 that resolve
some reported problems and add some a device id:
- new device id for r8188eu driver
- use-after-free bugfixes for the rtl8712 driver
- fix up firmware dependency problem for the r8188eu driver
All of these have been in linux-next for a while with no reported
problems"
* tag 'staging-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8712: fix use after free bugs
staging: r8188eu: Add Rosewill USB-N150 Nano to device tables
staging: r8188eu: add firmware dependency
Linus Torvalds [Sat, 3 Sep 2022 17:27:25 +0000 (10:27 -0700)]
Merge tag 'clk-fixes-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Here's a collection of primarily clk driver fixes, with a couple fixes
to the core framework.
We had to revert out a commit that affected boot on some devices that
have the CLK_OPS_PARENT_ENABLE flag set. It isn't critical to have
that fix so we'll try again next time.
Driver side fixes include:
- Plug an OF-node refcount bug in the TI clk driver
- Fix the error handling in the raspberry pi firmware get_rate so
that errors don't look like valid frequencies
- Avoid going out of bounds in the raspberry pi driver too if the
video firmware returns something we're not expecting"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops"
clk: bcm: rpi: Show clock id limit in error case
clk: bcm: rpi: Add missing newline
clk: bcm: rpi: Prevent out-of-bounds access
clk: bcm: rpi: Fix error handling of raspberrypi_fw_get_rate
clk: core: Fix runtime PM sequence in clk_core_unprepare()
clk: core: Honor CLK_OPS_PARENT_ENABLE for clk gate ops
clk: ti: Fix missing of_node_get() ti_find_clock_provider()
Linus Torvalds [Sat, 3 Sep 2022 17:24:30 +0000 (10:24 -0700)]
Merge tag 'hwmon-for-v6.0-rc4' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
- Fix out of bounds access in gpio-fan driver
- Fix VOUT margin caching in PMBus core
- Avoid error message after -EPROBE_DEFER from devm_regulator_register()
* tag 'hwmon-for-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (gpio-fan) Fix array out of bounds access
hwmon: (pmbus) Fix vout margin caching
hwmon: (pmbus) Use dev_err_probe() to filter -EPROBE_DEFER error messages
Steven Price [Fri, 2 Sep 2022 11:26:12 +0000 (12:26 +0100)]
mm: pagewalk: Fix race between unmap and page walker
The mmap lock protects the page walker from changes to the page tables
during the walk. However a read lock is insufficient to protect those
areas which don't have a VMA as munmap() detaches the VMAs before
downgrading to a read lock and actually tearing down PTEs/page tables.
For users of walk_page_range() the solution is to simply call pte_hole()
immediately without checking the actual page tables when a VMA is not
present. We now never call __walk_page_range() without a valid vma.
For walk_page_range_novma() the locking requirements are tightened to
require the mmap write lock to be taken, and then walking the pgd
directly with 'no_vma' set.
This in turn means that all page walkers either have a valid vma, or
it's that special 'novma' case for page table debugging. As a result,
all the odd '(!walk->vma && !walk->no_vma)' tests can be removed.
Fixes:
dd2283f2605e ("mm: mmap: zap pages with read mmap_sem in munmap")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ye xingchen [Fri, 26 Aug 2022 07:29:03 +0000 (07:29 +0000)]
LoongArch: mm: Remove the unneeded result variable
Return the value pa_to_nid() directly instead of storing it in another
redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Yupeng Li [Wed, 31 Aug 2022 05:40:17 +0000 (13:40 +0800)]
LoongArch: Fix arch_remove_memory() undefined build error
The kernel build error when unslected CONFIG_MEMORY_HOTREMOVE because
arch_remove_memory() is needed by mm/memory_hotplug.c but undefined.
Some build error messages like:
LD vmlinux.o
MODPOST vmlinux.symvers
MODINFO modules.builtin.modinfo
GEN modules.builtin
LD .tmp_vmlinux.kallsyms1
loongarch64-linux-gnu-ld: mm/memory_hotplug.o: in function `.L242':
memory_hotplug.c:(.ref.text+0x930): undefined reference to `arch_remove_memory'
make: *** [Makefile:1169:vmlinux] 错误 1
Removed CONFIG_MEMORY_HOTREMOVE requirement and rearrange the file refer
to the definitions of other platform architectures.
Signed-off-by: Yupeng Li <liyupeng@zbhlos.com>
Signed-off-by: Caicai <caizp2008@163.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Huacai Chen [Fri, 2 Sep 2022 14:33:42 +0000 (22:33 +0800)]
LoongArch: Fix section mismatch due to acpi_os_ioremap()
Now acpi_os_ioremap() is marked with __init because it calls memblock_
is_memory() which is also marked with __init in the !ARCH_KEEP_MEMBLOCK
case. However, acpi_os_ioremap() is called by ordinary functions such
as acpi_os_{read, write}_memory() and causes section mismatch warnings:
WARNING: modpost: vmlinux.o: section mismatch in reference: acpi_os_read_memory (section: .text) -> acpi_os_ioremap (section: .init.text)
WARNING: modpost: vmlinux.o: section mismatch in reference: acpi_os_write_memory (section: .text) -> acpi_os_ioremap (section: .init.text)
Fix these warnings by selecting ARCH_KEEP_MEMBLOCK unconditionally and
removing the __init modifier of acpi_os_ioremap(). This can also give a
chance to track "memory" and "reserved" memblocks after early boot.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Huacai Chen [Wed, 31 Aug 2022 06:22:43 +0000 (14:22 +0800)]
LoongArch: Improve dump_tlb() output messages
1, Use nr/nx to replace ri/xi;
2, Add 0x prefix for hexadecimal data.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Huacai Chen [Wed, 31 Aug 2022 03:19:27 +0000 (11:19 +0800)]
LoongArch: Adjust arch_do_signal_or_restart() to adapt generic entry
Commit
8ba62d37949e248c69 ("task_work: Call tracehook_notify_signal from
get_signal on all architectures") adjust arch_do_signal_or_restart() for
all architectures. LoongArch hasn't been upstream yet at that time and
can be still built successfully without adjustment because this function
has a weak version with the correct prototype. It is obviously that we
should convert LoongArch to use new API, otherwise some signal handlings
will be lost.
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Ard Biesheuvel [Wed, 24 Aug 2022 15:31:10 +0000 (17:31 +0200)]
LoongArch: Avoid orphan input sections
Ensure that all input sections are listed explicitly in the linker
script, and issue a warning otherwise. This ensures that the binary
image matches the PE/COFF and other image metadata exactly, which is
important for things like code signing.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Linus Torvalds [Fri, 2 Sep 2022 23:44:30 +0000 (16:44 -0700)]
Merge tag 'block-6.0-2022-09-02' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- error handling fix for the new auth code (Hannes Reinecke)
- fix unhandled tcp states in nvmet_tcp_state_change (Maurizio
Lombardi)
- add NVME_QUIRK_BOGUS_NID for Lexar NM610 (Shyamin Ayesh)
- Add documentation for the ublk driver merged in this merge window
(Ming)
* tag 'block-6.0-2022-09-02' of git://git.kernel.dk/linux-block:
Documentation: document ublk
nvmet-tcp: fix unhandled tcp states in nvmet_tcp_state_change()
nvmet-auth: add missing goto in nvmet_setup_auth()
nvme-pci: add NVME_QUIRK_BOGUS_NID for Lexar NM610
Linus Torvalds [Fri, 2 Sep 2022 23:37:01 +0000 (16:37 -0700)]
Merge tag 'io_uring-6.0-2022-09-02' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- A single fix for over-eager retries for networking (Pavel)
- Revert the notification slot support for zerocopy sends.
It turns out that even after more than a year or development and
testing, there's not full agreement on whether just using plain
ordered notifications is Good Enough to avoid the complexity of using
the notifications slots. Because of that, we decided that it's best
left to a future final decision.
We can always bring back this feature, but we can't really change it
or remove it once we've released 6.0 with it enabled. The reverts
leave the usual CQE notifications as the primary interface for
knowing when data was sent, and when it was acked. (Pavel)
* tag 'io_uring-6.0-2022-09-02' of git://git.kernel.dk/linux-block:
selftests/net: return back io_uring zc send tests
io_uring/net: simplify zerocopy send user API
io_uring/notif: remove notif registration
Revert "io_uring: rename IORING_OP_FILES_UPDATE"
Revert "io_uring: add zc notification flush requests"
selftests/net: temporarily disable io_uring zc test
io_uring/net: fix overexcessive retries
Linus Torvalds [Fri, 2 Sep 2022 23:20:24 +0000 (16:20 -0700)]
Merge tag '6.0-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Five fixes, all also marked for stable:
- fixes for collapse range and insert range (also fixes xfstest
generic/031)
- memory leak fix"
* tag '6.0-rc3-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix small mempool leak in SMB2_negotiate()
smb3: use filemap_write_and_wait_range instead of filemap_write_and_wait
smb3: fix temporary data corruption in insert range
smb3: fix temporary data corruption in collapse range
smb3: Move the flush out of smb2_copychunk_range() into its callers
Linus Torvalds [Fri, 2 Sep 2022 22:24:08 +0000 (15:24 -0700)]
Merge tag 'landlock-6.0-rc4' of git://git./linux/kernel/git/mic/linux
Pull landlock fix from Mickaël Salaün:
"This fixes a mis-handling of the LANDLOCK_ACCESS_FS_REFER right when
multiple rulesets/domains are stacked.
The expected behaviour was that an additional ruleset can only
restrict the set of permitted operations, but in this particular case,
it was potentially possible to re-gain the LANDLOCK_ACCESS_FS_REFER
right"
* tag 'landlock-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/mic/linux:
landlock: Fix file reparenting without explicit LANDLOCK_ACCESS_FS_REFER
Linus Torvalds [Fri, 2 Sep 2022 22:03:12 +0000 (15:03 -0700)]
Merge tag 'mmc-v6.0-rc2' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix workaround for SD UHS-I voltage switch
* tag 'mmc-v6.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: core: Fix inconsistent sd3_bus_mode at UHS-I SD voltage switch failure
mmc: core: Fix UHS-I SD 1.8V workaround branch
Linus Torvalds [Fri, 2 Sep 2022 21:56:09 +0000 (14:56 -0700)]
Merge tag 'drm-fixes-2022-09-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Regular fixes pull. One core dma-buf fix, then two weeks of i915
fixes, a lot of amdgpu fixes mostly for new IP, and a bunch of msm
fixes, mostly modesetting ones.
Nothing seems too bad at this point.
dma-buf/dma-resv:
- Fence-handling fix
i915:
- GVT fixes including fix for a CommetLake regression in mmio table
and misc doc and typo fixes
- Fix CCS handling
- Fix for guc requests after reset
- Display DSI related fixes
- Display backlight related fixes
- Fix for a null pointer dereference
- HDMI related quirk for ECS Liva Q2 with GLK graphics
- Skip wm/ddb readout for disabled pipes
amdgpu:
- FRU error message fix
- MES 11 updates
- DCN 3.2.x fixes
- DCN 3.1.4 fixes
- Fix possible use after free in CS IOCTL
- SMU 13.0.x fixes
- Fix iolink reporting on devices with direct connections to CPU
- GFX10 tap delay firmware fixes
msm:
- Fix for inconsistent indenting in msm_dsi_dphy_timing_calc_v3().
- Fix to make eDP the first connector in the connected list.
- Fix to populate intf_cfg correctly before calling reset_intf_cfg().
- Specify the correct number of DSI regulators for SDM660.
- Specify the correct number of DSI regulators for MSM8996.
- Fix for removing DP_RECOVERED_CLOCK_OUT_EN bit for tps4 link training
- Fix probe-deferral crash in gpu devfreq
- Fix gpu debugfs deadlock"
* tag 'drm-fixes-2022-09-02' of git://anongit.freedesktop.org/drm/drm: (51 commits)
drm/amd/amdgpu: skip ucode loading if ucode_size == 0
drm/amdgpu: only init tap_delay ucode when it's included in ucode binary
drm/amd/display: Fix black flash when switching from ODM2to1 to ODMBypass
drm/amd/display: Fix check for stream and plane
drm/amd/display: Re-initialize viewport after pipe merge
drm/amd/display: Use correct plane for CAB cursor size allocation
drm/amdgpu: ensure no PCIe peer access for CPU XGMI iolinks
drm/amd/pm: bump SMU 13.0.0 driver_if header version
drm/amd/pm: use vbios carried pptable for all SMU13.0.7 SKUs
drm/amd/pm: use vbios carried pptable for those supported SKUs
drm/amd/display: fix wrong register access
drm/amd/display: use actual cursor size instead of max for CAB allocation
drm/amd/display: disable display fresh from MALL on an edge case for DCN321
drm/amd/display: Fix CAB cursor size allocation for DCN32/321
drm/amd/display: Missing HPO instance added
drm/amd/display: set dig fifo read start level to 7 before dig fifo reset
drm/amdgpu: Fix use-after-free in amdgpu_cs_ioctl
drm/amd/display: Fix OTG H timing reset for dcn314
drm/amd/display: Fix DCN32 DPSTREAMCLK_CNTL programming
drm/amdgpu: Update mes_v11_api_def.h
...
Linus Torvalds [Fri, 2 Sep 2022 17:55:23 +0000 (10:55 -0700)]
Merge tag 'driver-core-6.0-rc4' of git://git./linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core fixes for some oft-reported problems
in 6.0-rc1. They include:
- a bunch of reverts to handle driver_deferred_probe_check_state()
problems that were part of the 6.0-rc1 merge.
- firmware_loader bugfixes now that the code is being properly tested
and used by others
- arch_topology fix
- deferred driver probe bugfix to solve a long-suffering amba bus
problem that many people have reported.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
firmware_loader: Fix memory leak in firmware upload
firmware_loader: Fix use-after-free during unregister
arch_topology: Silence early cacheinfo errors when non-existent
driver core: Don't probe devices after bus_type.match() probe deferral
Revert "iommu/of: Delete usage of driver_deferred_probe_check_state()"
Revert "PM: domains: Delete usage of driver_deferred_probe_check_state()"
Revert "net: mdio: Delete usage of driver_deferred_probe_check_state()"
Revert "driver core: Delete driver_deferred_probe_check_state()"
Linus Torvalds [Fri, 2 Sep 2022 17:50:08 +0000 (10:50 -0700)]
Merge tag 'char-misc-6.0-rc4' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc and other driver fixes for 6.0-rc4.
Included in here are:
- binder fixes for previous fixes, and a few more fixes uncovered by
them.
- iio driver fixes
- soundwire driver fixes
- fastrpc driver fixes for memory corruption on some hardware
- peci driver fix
- mhi driver fix
All of these have been in linux-next with no reported problems"
* tag 'char-misc-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix alloc->vma_vm_mm null-ptr dereference
misc: fastrpc: increase maximum session count
misc: fastrpc: fix memory corruption on open
misc: fastrpc: fix memory corruption on probe
soundwire: qcom: fix device status array range
bus: mhi: host: Fix up null pointer access in mhi_irq_handler
soundwire: qcom: remove duplicate reset control get
iio: light: cm32181: make cm32181_pm_ops static
iio: ad7292: Prevent regulator double disable
dt-bindings: iio: gyroscope: bosch,bmg160: correct number of pins
iio: adc: mcp3911: use correct formula for AD conversion
iio: adc: mcp3911: correct "microchip,device-addr" property
Revert "binder_alloc: Add missing mmap_lock calls when using the VMA"
binder_alloc: Add missing mmap_lock calls when using the VMA
binder: fix UAF of ref->proc caused by race condition
iio: light: cm3605: Fix an error handling path in cm3605_probe()
iio: adc: mcp3911: make use of the sign bit
peci: cpu: Fix use-after-free in adev_release()
peci: aspeed: fix error check return value of platform_get_irq()
Linus Torvalds [Fri, 2 Sep 2022 17:43:46 +0000 (10:43 -0700)]
Merge tag 'usb-6.0-rc4' of git://git./linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt driver fixes from Greg KH:
"Here are a lot of small USB and Thunderbolt driver fixes for 6.0-rc4
for reported problems. Included in here are:
- new usb-serial driver ids
- dwc3 driver bugfixes for reported problems with 6.0-rc1
- new device quirks, and reverts of some quirks that were incorrect
- gadget driver bugfixes for reported problems
- USB host controller bugfixes (xhci and others)
- other small USB fixes, details in the shortlog
- small thunderbolt driver fixes
All of these have been in linux-next with no reported issues"
* tag 'usb-6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (51 commits)
Revert "usb: gadget: udc-xilinx: replace memcpy with memcpy_toio"
usb: storage: Add ASUS <0x0b05:0x1932> to IGNORE_UAS
USB: serial: ch341: fix disabled rx timer on older devices
USB: serial: ch341: fix lost character on LCR updates
USB: serial: cp210x: add Decagon UCA device id
Revert "usb: add quirks for Lenovo OneLink+ Dock"
usb: cdns3: fix issue with rearming ISO OUT endpoint
usb: cdns3: fix incorrect handling TRB_SMM flag for ISOC transfer
usb: gadget: mass_storage: Fix cdrom data transfers on MAC-OS
media: mceusb: Use new usb_control_msg_*() routines
USB: core: Prevent nested device-reset calls
USB: gadget: Fix obscure lockdep violation for udc_mutex
usb: dwc2: fix wrong order of phy_power_on and phy_init
usb: gadget: udc-xilinx: replace memcpy with memcpy_toio
usb: typec: Remove retimers properly
usb: dwc3: disable USB core PHY management
usb: add quirks for Lenovo OneLink+ Dock
USB: serial: option: add support for Cinterion MV32-WA/WB RmNet mode
USB: serial: ftdi_sio: add Omron CS1W-CIF31 device id
USB: serial: option: add Quectel EM060K modem
...
Linus Torvalds [Fri, 2 Sep 2022 17:35:51 +0000 (10:35 -0700)]
Merge tag 'platform-drivers-x86-v6.0-2' of git://git./linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"Various small fixes and hardware-id additions"
* tag 'platform-drivers-x86-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: p2sb: Fix UAF when caller uses resource name
platform/x86: asus-wmi: Increase FAN_CURVE_BUF_LEN to 32
platform/mellanox: Remove redundant 'NULL' check
platform/mellanox: Remove unnecessary code
platform/mellanox: mlxreg-lc: Fix locking issue
platform/mellanox: mlxreg-lc: Fix coverity warning
platform/x86: acer-wmi: Acer Aspire One AOD270/Packard Bell Dot keymap fixes
platform/x86: thinkpad_acpi: Explicitly set to balanced mode on startup
platform/x86: asus-wmi: Fix the name of the mic-mute LED classdev
platform/surface: aggregator_registry: Add HID devices for sensors and UCSI client to SP8
platform/surface: aggregator_registry: Rename HID device nodes based on new findings
platform/surface: aggregator_registry: Rename HID device nodes based on their function
platform/surface: aggregator_registry: Add support for Surface Laptop Go 2
platform/x86: x86-android-tablets: Fix broken touchscreen on Chuwi Hi8 with Windows BIOS
platform/x86: pmc_atom: Fix SLP_TYPx bitfield mask
Linus Torvalds [Fri, 2 Sep 2022 17:32:30 +0000 (10:32 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"It's a lot smaller than last week, with the star of the show being a
couple of fixes to head.S addressing a boot regression introduced by
the recent overhaul of that code in non-default configurations (i.e.
KASLR disabled).
The first of those two resolves the issue reported (and bisected) by
Mikulus in the wait_on_bit() thread.
Summary:
- Fix two boot issues caused by the recent head.S rework when !KASLR
- Fix calculation of crashkernel memory reservation
- Fix bogus error check in PMU IRQ probing code"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Reserve enough pages for the initial ID map
perf/arm_pmu_platform: fix tests for platform_get_irq() failure
arm64: head: Ignore bogus KASLR displacement on non-relocatable kernels
arm64/kexec: Fix missing extra range for crashkres_low.
Ming Lei [Fri, 2 Sep 2022 15:23:02 +0000 (23:23 +0800)]
Documentation: document ublk
Add documentation for ublk subsystem. It was supposed to be documented when
merging the driver, but missing at that time.
Cc: Bagas Sanjaya <bagasdotme@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Xiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: ZiyangZhang <ZiyangZhang@linux.alibaba.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[axboe: correct MAINTAINERS addition]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mickaël Salaün [Wed, 31 Aug 2022 20:38:40 +0000 (22:38 +0200)]
landlock: Fix file reparenting without explicit LANDLOCK_ACCESS_FS_REFER
This change fixes a mis-handling of the LANDLOCK_ACCESS_FS_REFER right
when multiple rulesets/domains are stacked. The expected behaviour was
that an additional ruleset can only restrict the set of permitted
operations, but in this particular case, it was potentially possible to
re-gain the LANDLOCK_ACCESS_FS_REFER right.
With the introduction of LANDLOCK_ACCESS_FS_REFER, we added the first
globally denied-by-default access right. Indeed, this lifted an initial
Landlock limitation to rename and link files, which was initially always
denied when the source or the destination were different directories.
This led to an inconsistent backward compatibility behavior which was
only taken into account if no domain layer were using the new
LANDLOCK_ACCESS_FS_REFER right. However, when restricting a thread with
a new ruleset handling LANDLOCK_ACCESS_FS_REFER, all inherited parent
rulesets/layers not explicitly handling LANDLOCK_ACCESS_FS_REFER would
behave as if they were handling this access right and with all their
rules allowing it. This means that renaming and linking files could
became allowed by these parent layers, but all the other required
accesses must also be granted: all layers must allow file removal or
creation, and renaming and linking operations cannot lead to privilege
escalation according to the Landlock policy. See detailed explanation
in commit
b91c3e4ea756 ("landlock: Add support for file reparenting with
LANDLOCK_ACCESS_FS_REFER").
To say it another way, this bug may lift the renaming and linking
limitations of the initial Landlock version, and a same ruleset can
enforce different restrictions depending on previous or next enforced
ruleset (i.e. inconsistent behavior). The LANDLOCK_ACCESS_FS_REFER right
cannot give access to data not already allowed, but this doesn't follow
the contract of the first Landlock ABI. This fix puts back the
limitation for sandboxes that didn't opt-in for this additional right.
For instance, if a first ruleset allows LANDLOCK_ACCESS_FS_MAKE_REG on
/dst and LANDLOCK_ACCESS_FS_REMOVE_FILE on /src, renaming /src/file to
/dst/file is denied. However, without this fix, stacking a new ruleset
which allows LANDLOCK_ACCESS_FS_REFER on / would now permit the
sandboxed thread to rename /src/file to /dst/file .
This change fixes the (absolute) rule access rights, which now always
forbid LANDLOCK_ACCESS_FS_REFER except when it is explicitly allowed
when creating a rule.
Making all domain handle LANDLOCK_ACCESS_FS_REFER was an initial
approach but there is two downsides:
* it makes the code more complex because we still want to check that a
rule allowing LANDLOCK_ACCESS_FS_REFER is legitimate according to the
ruleset's handled access rights (i.e. ABI v1 != ABI v2);
* it would not allow to identify if the user created a ruleset
explicitly handling LANDLOCK_ACCESS_FS_REFER or not, which will be an
issue to audit Landlock.
Instead, this change adds an ACCESS_INITIALLY_DENIED list of
denied-by-default rights, which (only) contains
LANDLOCK_ACCESS_FS_REFER. All domains are treated as if they are also
handling this list, but without modifying their fs_access_masks field.
A side effect is that the errno code returned by rename(2) or link(2)
*may* be changed from EXDEV to EACCES according to the enforced
restrictions. Indeed, we now have the mechanic to identify if an access
is denied because of a required right (e.g. LANDLOCK_ACCESS_FS_MAKE_REG,
LANDLOCK_ACCESS_FS_REMOVE_FILE) or if it is denied because of missing
LANDLOCK_ACCESS_FS_REFER rights. This may result in different errno
codes than for the initial Landlock version, but this approach is more
consistent and better for rename/link compatibility reasons, and it
wasn't possible before (hence no backport to ABI v1). The
layout1.rename_file test reflects this change.
Add 4 layout1.refer_denied_by_default* test suites to check that the
behavior of a ruleset not handling LANDLOCK_ACCESS_FS_REFER (ABI v1) is
unchanged even if another layer handles LANDLOCK_ACCESS_FS_REFER (i.e.
ABI v1 precedence). Make sure rule's absolute access rights are correct
by testing with and without a matching path. Add test_rename() and
test_exchange() helpers.
Extend layout1.inval tests to check that a denied-by-default access
right is not necessarily part of a domain's handled access rights.
Test coverage for security/landlock is 95.3% of 599 lines according to
gcc/gcov-11.
Fixes:
b91c3e4ea756 ("landlock: Add support for file reparenting with LANDLOCK_ACCESS_FS_REFER")
Reviewed-by: Paul Moore <paul@paul-moore.com>
Reviewed-by: Günther Noack <gnoack3000@gmail.com>
Link: https://lore.kernel.org/r/20220831203840.1370732-1-mic@digikod.net
Cc: stable@vger.kernel.org
[mic: Constify and slightly simplify test helpers]
Signed-off-by: Mickaël Salaün <mic@digikod.net>
Dan Carpenter [Thu, 1 Sep 2022 15:35:20 +0000 (18:35 +0300)]
xen/grants: prevent integer overflow in gnttab_dma_alloc_pages()
The change from kcalloc() to kvmalloc() means that arg->nr_pages
might now be large enough that the "args->nr_pages << PAGE_SHIFT" can
result in an integer overflow.
Fixes:
b3f7931f5c61 ("xen/gntdev: switch from kcalloc() to kvcalloc()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/YxDROJqu/RPvR0bi@kili
Signed-off-by: Juergen Gross <jgross@suse.com>
SeongJae Park [Wed, 31 Aug 2022 16:58:24 +0000 (16:58 +0000)]
xen-blkfront: Cache feature_persistent value before advertisement
Xen blkfront advertises its support of the persistent grants feature
when it first setting up and when resuming in 'talk_to_blkback()'.
Then, blkback reads the advertised value when it connects with blkfront
and decides if it will use the persistent grants feature or not, and
advertises its decision to blkfront. Blkfront reads the blkback's
decision and it also makes the decision for the use of the feature.
Commit
402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter
when connect"), however, made the blkfront's read of the parameter for
disabling the advertisement, namely 'feature_persistent', to be done
when it negotiate, not when advertise. Therefore blkfront advertises
without reading the parameter. As the field for caching the parameter
value is zero-initialized, it always advertises as the feature is
disabled, so that the persistent grants feature becomes always disabled.
This commit fixes the issue by making the blkfront does parmeter caching
just before the advertisement.
Fixes:
402c43ea6b34 ("xen-blkfront: Apply 'feature_persistent' parameter when connect")
Cc: <stable@vger.kernel.org> # 5.10.x
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220831165824.94815-4-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
SeongJae Park [Wed, 31 Aug 2022 16:58:23 +0000 (16:58 +0000)]
xen-blkfront: Advertise feature-persistent as user requested
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit
74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent
grants") made a field of blkfront, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkfront saves
the parameter value in a separate place and advertises the support based
on only the saved value.
Fixes:
74a852479c68 ("xen-blkfront: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220831165824.94815-3-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
SeongJae Park [Wed, 31 Aug 2022 16:58:22 +0000 (16:58 +0000)]
xen-blkback: Advertise feature-persistent as user requested
The advertisement of the persistent grants feature (writing
'feature-persistent' to xenbus) should mean not the decision for using
the feature but only the availability of the feature. However, commit
aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent
grants") made a field of blkback, which was a place for saving only the
negotiation result, to be used for yet another purpose: caching of the
'feature_persistent' parameter value. As a result, the advertisement,
which should follow only the parameter value, becomes inconsistent.
This commit fixes the misuse of the semantic by making blkback saves the
parameter value in a separate place and advertises the support based on
only the saved value.
Fixes:
aac8a70db24b ("xen-blkback: add a parameter for disabling of persistent grants")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Juergen Gross <jgross@suse.com>
Signed-off-by: SeongJae Park <sj@kernel.org>
Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220831165824.94815-2-sj@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Nathan Chancellor [Tue, 30 Aug 2022 15:12:56 +0000 (08:12 -0700)]
powerpc/papr_scm: Ensure rc is always initialized in papr_scm_pmu_register()
Clang warns:
arch/powerpc/platforms/pseries/papr_scm.c:492:6: warning: variable 'rc' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!p->stat_buffer_len)
^~~~~~~~~~~~~~~~~~~
arch/powerpc/platforms/pseries/papr_scm.c:523:64: note: uninitialized use occurs here
dev_info(&p->pdev->dev, "nvdimm pmu didn't register rc=%d\n", rc);
^~
include/linux/dev_printk.h:150:67: note: expanded from macro 'dev_info'
dev_printk_index_wrap(_dev_info, KERN_INFO, dev, dev_fmt(fmt), ##__VA_ARGS__)
^~~~~~~~~~~
include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
^~~~~~~~~~~
arch/powerpc/platforms/pseries/papr_scm.c:492:2: note: remove the 'if' if its condition is always false
if (!p->stat_buffer_len)
^~~~~~~~~~~~~~~~~~~~~~~~
arch/powerpc/platforms/pseries/papr_scm.c:484:8: note: initialize the variable 'rc' to silence this warning
int rc, nodeid;
^
= 0
1 warning generated.
The call to papr_scm_pmu_check_events() was eliminated but a return code
was not added to the if statement. Add the same return code from
papr_scm_pmu_check_events() for this condition so there is no more
warning.
Fixes:
9b1ac04698a4 ("powerpc/papr_scm: Fix nvdimm event mappings")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://github.com/ClangBuiltLinux/linux/issues/1701
Link: https://lore.kernel.org/r/20220830151256.1473169-1-nathan@kernel.org