Soeren Moch [Thu, 27 Nov 2014 20:21:44 +0000 (21:21 +0100)]
tbs2910: fix lost characters on serial input
With enabled console_mux for serial input and usb keyboard sometimes
characters get lost when typing too fast at the serial input (pasting
strings in serial console window). Fix this by using INT_QUEUE for
polling the usb keyboard.
Signed-off-by: Soeren Moch <smoch@web.de>
Stefan Roese [Thu, 27 Nov 2014 12:46:43 +0000 (13:46 +0100)]
arm: mx6: Change defines ENET_xxMHz to ENET_xxMHZ (no CamelCase)
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Soeren Moch [Thu, 27 Nov 2014 09:11:41 +0000 (10:11 +0100)]
sata: fix reset_sata for dwc_ahsata
- fix crash when sata device is not initialized
- remove disable_sata_clock() since it is not clear which clock for which
device should be disabled here
- call disable_sata_clock() for mx6 in preboot_os instead
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Soeren Moch [Wed, 26 Nov 2014 11:39:24 +0000 (12:39 +0100)]
tbs2910: fix Kconfig
fix Kconfig for tbs2910 board to prevent crash on relocation
Signed-off-by: Soeren Moch <smoch@web.de>
Fabio Estevam [Tue, 25 Nov 2014 15:11:08 +0000 (13:11 -0200)]
mxc_ocotp: Do not disable the OCOTP clock after every access
Leave the OCOTP turned on, so that we subsequent access do not fail.
After enabling the thermal driver on a mx6sxsabresd board:
U-Boot 2015.01-rc1-18267-g99d4189-dirty (Nov 24 2014 - 12:59:01)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 48 C
Reset cause: POR
Board: MX6SX SABRE SDB
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
00:01.0 - 16c3:abcd - Bridge device
01:00.0 - 8086:08b1 - Network controller
In: serial
Out: serial
Err: serial
Net:
(hang)
As the thermal driver accesses the ocotp registers, its clock will be disabled
afterwards.
Then when the MAC address is read (also from ocotp registers) it will cause a
hang.
Do not disable the ocotp clock to prevent this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Fabio Estevam [Tue, 25 Nov 2014 15:11:07 +0000 (13:11 -0200)]
mx6sxsabresd: Add thermal support
Add thermal support so that the temperature of the chip can be displayed on
boot:
U-Boot 2015.01-rc1-18268-g1366c05-dirty (Nov 25 2014 - 13:02:42)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 50 C
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Mon, 24 Nov 2014 14:24:15 +0000 (12:24 -0200)]
thermal: imx_thermal: Do not display calibration data
Printing the calibration data on every boot does not provide really useful
information:
U-Boot 2015.01-rc1-18266-ge7eb277 (Nov 24 2014 - 11:29:51)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
CPU: Thermal calibration data: 0x5d85067d
CPU: Temperature 33 C
Reset cause: POR
Board: MX6-SabreSD
Do not display the calibration data in order to have a cleaner boot log.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Hector Palacios [Fri, 21 Nov 2014 16:54:44 +0000 (17:54 +0100)]
mxs_ocotp: clear the error flag before initiating write operation
A previous operation may have set the error flag, which must be cleared
before a new write operation can be issued.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Hector Palacios [Fri, 21 Nov 2014 16:54:43 +0000 (17:54 +0100)]
mxs_ocotp: check for errors from the OTP controller after writing
The write operation may fail when trying to write to a locked area. In
this case the ERROR bit is set in the CTRL register. Check for that
condition and return an error.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Hector Palacios [Fri, 21 Nov 2014 16:54:42 +0000 (17:54 +0100)]
mxs_ocotp: prevent error path from returning success
The code may goto 'fail' upon error with 'ret' variable set to an error
code, but this variable was being overwritten by a final preparation
function to restore the HCLK, so success was (in general) returned even
after an error was hit previously.
With this change, the function may now return success even if the final
preparation function fails, but it's probably enough to print a message
because (if successful) the real programming of the fuses has already
completed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Guillaume GARDET [Thu, 20 Nov 2014 07:38:31 +0000 (08:38 +0100)]
imx: mx53loco: Add raw initrd support
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Tom Rini [Mon, 24 Nov 2014 22:08:47 +0000 (17:08 -0500)]
Prepare v2015.01-rc2
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 24 Nov 2014 22:05:11 +0000 (17:05 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-arm
Rabin Vincent [Fri, 21 Nov 2014 22:05:22 +0000 (23:05 +0100)]
Revert "hush: fix segfault on syntax error"
128059b92 ("hush: fix segfault on syntax error") attempted to fix a
segfault on syntax errors, but it broke Ctrl-C handling, and the
assumption that it made, that rcode could not be -1, is incorrect.
Revert this change.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reported-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Tom Rini [Mon, 24 Nov 2014 17:02:12 +0000 (12:02 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-imx
Tom Rini [Mon, 24 Nov 2014 17:01:48 +0000 (12:01 -0500)]
Merge git://git.denx.de/u-boot-dm
Conflicts:
drivers/serial/serial-uclass.c
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Mon, 24 Nov 2014 17:00:00 +0000 (12:00 -0500)]
Merge git://git.denx.de/u-boot-x86
Conflicts:
arch/x86/cpu/Makefile
Signed-off-by: Tom Rini <trini@ti.com>
Fabio Estevam [Fri, 21 Nov 2014 18:42:58 +0000 (16:42 -0200)]
mx6boards: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Benard <eric@eukrea.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 21 Nov 2014 18:42:57 +0000 (16:42 -0200)]
nitrogen6x: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Fri, 21 Nov 2014 18:42:56 +0000 (16:42 -0200)]
ot1200: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Nikita Kiryanov [Fri, 21 Nov 2014 10:47:26 +0000 (12:47 +0200)]
arm: imx: stop sata on boot
Ideally, the Linux kernel should get the hardware in its most
untouched state. For the most part, U-Boot does not reset the various
subsystems it touches before boot, and usually Linux deals with it, but
on some boards (cm_fx6) the Linux kernel fails to detect the ssd
correctly if sata is used by U-Boot.
Power off sata on OS boot so that Linux will have a clean state to work
with.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Nikita Kiryanov [Fri, 21 Nov 2014 10:47:25 +0000 (12:47 +0200)]
arm: mx6: cm_fx6: implement board specific sata stop
Provide board specific implementation for sata stop command for
cm_fx6.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Nikita Kiryanov [Fri, 21 Nov 2014 10:47:24 +0000 (12:47 +0200)]
cmd_sata: implement sata stop command
Implement sata stop command.
This introduces the __sata_stop() weak function, which mirrors
the weak __sata_initialize() function, giving users the option of
undoing the custom steps performed in overrides of sata_initialize().
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Nikita Kiryanov [Fri, 21 Nov 2014 10:47:23 +0000 (12:47 +0200)]
sata: implement reset_sata for dwc_ahsata
Add reset_sata() to the sata driver interface and implement it
for dwc_ahsata. This function cleans up after sata_init(), and
therefore accepts a device number like sata_init() does.
A dummy implementation is provided for the rest of the drivers.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Nikita Kiryanov [Fri, 21 Nov 2014 10:47:22 +0000 (12:47 +0200)]
arm: mx6: introduce disable_sata_clock
Implement disable_sata_clock for mx6 SoCs.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Thu, 20 Nov 2014 15:17:56 +0000 (13:17 -0200)]
gw_ventana: Use the generic spl_sd.cfg
gw_ventana can boot from SPI or NAND and both of these interfaces boot from
the same 0x400 offset.
This means that we could simplify the code and replace the custom gw_ventana.cfg
with the generic spl_sd.cfg, as it provides the same boot offset of 0x400.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Hans de Goede [Fri, 14 Nov 2014 08:34:31 +0000 (09:34 +0100)]
ARM: bootm: Allow booting in secure mode on hyp capable systems
Older Linux kernels will not properly boot in hyp mode, add support for a
bootm_boot_mode environment variable, which can be set to "sec" or "nonsec"
to force booting in secure or non-secure mode when build with non-sec support.
The default behavior can be selected through CONFIG_ARMV7_BOOT_SEC_DEFAULT,
when this is set booting in secure mode is the default. The default setting
for this Kconfig option is N, preserving the current behavior of booting in
non-secure mode by default when non-secure mode is supported.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Hans de Goede [Fri, 14 Nov 2014 08:34:30 +0000 (09:34 +0100)]
ARM: Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options
Add arch/arm/cpu/armv7/Kconfig with non-secure and virt options, this is a
preparation patch for adding an env variable to choose between secure /
non-secure boot on non-secure boot capable systems, specifically this
prepares for adding CONFIG_ARMV7_BOOT_SEC_DEFAULT as a proper Kconfig option.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tom Rini [Fri, 14 Nov 2014 08:34:29 +0000 (09:34 +0100)]
Kconfig: Add EXPERT option
For similar reasons to why the Linux Kernel has an EXPERT option, we too
want an option to allow for tweaking of some options that while normally
should remain hidden, may need to be changed in some cases.
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Suriyan Ramasami [Mon, 17 Nov 2014 22:39:39 +0000 (14:39 -0800)]
sandbox: script for testing sandbox/ext4/fat/fs commands
Test size/read/write commands in a sandbox environment.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Suriyan Ramasami [Mon, 17 Nov 2014 22:39:38 +0000 (14:39 -0800)]
fs: API changes enabling extra parameter to return size of type loff_t
The sandbox/ext4/fat/generic fs commands do not gracefully deal with files
greater than 2GB. Negative values are returned in such cases.
To handle this, the fs functions have been modified to take an additional
parameter of type "* loff_t" which is then populated. The return value
of the fs functions are used only for error conditions.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update board/gdsys/p1022/controlcenterd-id.c,
drivers/fpga/zynqpl.c for changes]
Signed-off-by: Tom Rini <trini@ti.com>
Suriyan Ramasami [Mon, 17 Nov 2014 22:39:37 +0000 (14:39 -0800)]
sandbox: Prepare API change for files greater than 2GB
Change the internal sandbox functions to use loff_t for file offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Suriyan Ramasami [Mon, 17 Nov 2014 22:39:36 +0000 (14:39 -0800)]
ext4: Prepare API change for files greater than 2GB
Change the internal EXT4 functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Update common/spl/spl_ext.c]
Signed-off-by: Tom Rini <trini@ti.com>
Suriyan Ramasami [Mon, 17 Nov 2014 22:39:35 +0000 (14:39 -0800)]
fat: Prepare API change for files greater than 2GB
Change the internal FAT functions to use loff_t for offsets.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
[trini: Fix fs/fat/fat.c for min3 updates]
Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Sat, 22 Nov 2014 13:11:08 +0000 (08:11 -0500)]
board/esd/common/auto_update.c: Use <flash.h>
A number of prototypes here are now found in <flash.h>. use.
Signed-off-by: Tom Rini <trini@ti.com>
Suriyan Ramasami [Mon, 17 Nov 2014 22:39:34 +0000 (14:39 -0800)]
sandbox: Use md5sum and fatwrite to enable testing of fs commands
Enable md5sum to obtain the MD5 of the read and written files to check
their contents for validity.
Use map_sysmem() to map buffer in a sandbox environment.
Signed-off-by: Suriyan Ramasami <suriyan.r@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Daniel Schwierzeck [Sat, 15 Nov 2014 22:46:53 +0000 (23:46 +0100)]
common/board_f: fix gcc warning on MIPS64
This fixes following warning when compiled with MIPS64
common/board_f.c: In function 'display_text_info':
common/board_f.c:150:2: warning: format '%X' expects argument i
of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat=]
debug("U-Boot code: %08X -> %08lX BSS: -> %08lX\n",
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Daniel Schwierzeck [Sat, 15 Nov 2014 22:46:52 +0000 (23:46 +0100)]
common/board_f: add setup of initial stack frame for MIPS
The MIPS specific setup of the initial stack frame was not
ported to generic board_f.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Masahiro Yamada [Thu, 13 Nov 2014 10:29:09 +0000 (19:29 +0900)]
spl: fix descending condition to drivers/mtd/nand/
SPL should not reference CONFIG_CMD_NAND to decide whether or not
it should build drivers/mtd/nand. CONFIG_CMD_NAND should be only
used to select the NAND utility command on the command parser.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 13 Nov 2014 10:29:08 +0000 (19:29 +0900)]
commands: add more command entries in Kconfig
This commit adds some of command entries (CONFIG_CMD_*) to
cover include/config_cmd_default.h and a little extra.
Because U-Boot supports lots of commands, they should be categorized
according to their usage.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 13 Nov 2014 10:29:07 +0000 (19:29 +0900)]
hush: add CONFIG_HUSH_PARSER to Kconfig
The README file states that the macros beginning with "CONFIG_SYS_"
depend on the hardware etc. and should not be meddled with if you do
not what you're doing.
We have already screwed up with this policy; we have given the prefix
"CONFIG_SYS_" to many user-selectable configurations.
Here, "CONFIG_SYS_HUSH_PARSER" is one of them. Users can enable it
if they want to use a more powerful command line parser, or disable it
if they only need a simple one.
This commit attempts to rename CONFIG_SYS_HUSH_PARSER to
CONFIG_HUSH_PARSER and move it to Kconfig.
Every board maintainer is expected to enable CONFIG_HUSH_PARSER
(= add "CONFIG_HUSH_PARSER=y" to his defconfig file) and remove
"#define CONFIG_SYS_HUSH_PARSER" from his header file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 13 Nov 2014 10:29:06 +0000 (19:29 +0900)]
FIT: add some FIT configurations to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 13 Nov 2014 09:43:52 +0000 (18:43 +0900)]
config: remove redundant CONFIG_SYS_PROMPT defines
Since commit
0defddc851ed (config: Add a default CONFIG_SYS_PROMPT),
each board header does not need to define CONFIG_SYS_PROMPT
as long as it uses the default prompt "=> ".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 13 Nov 2014 03:28:43 +0000 (12:28 +0900)]
tegra: do not descend into empty directories
Some tegra makefiles only contain a dummy line to generate
a built-in.o. Let's do not descend into such directories.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Thu, 13 Nov 2014 03:28:42 +0000 (12:28 +0900)]
kbuild: use SoC-specific CONFIG to descend into SoC directory
Use "obj-$(CONFIG_FOO) += foo/" where it is possible.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 13 Nov 2014 03:28:41 +0000 (12:28 +0900)]
x86: use CONFIG_SYS_COREBOOT to descend into coreboot/ directory
The references of CONFIG_SYS_COREBOOT in arch/x86/cpu/coreboot/Makefile
are redundant because the build system descends into the directory
only when CONFIG_SYS_COREBOOT is defined.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Thu, 13 Nov 2014 03:28:40 +0000 (12:28 +0900)]
kbuild: Descend into SOC directory from CPU directory
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Thierry Reding [Thu, 13 Nov 2014 01:26:50 +0000 (18:26 -0700)]
Add pr_fmt() macro
This macro can be overridden in source files (before including common.h)
and can be used to specify a prefix for debug and error messages. An
example of how to use this is shown below:
#define pr_fmt(fmt) "foo: " fmt
#include <common.h>
...
debug("bar");
The resulting message will read:
foo: bar
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Thu, 13 Nov 2014 01:26:49 +0000 (18:26 -0700)]
pci: Honour pci_skip_dev()
When enumerating devices, honour the pci_skip_dev() function. This can
be used by PCI controller drivers to restrict which devices will be
probed.
This is required by the NVIDIA Tegra PCIe controller driver, which will
fail with a data abort exception if an access is attempted to a device
number larger than 0 outside of bus 0. pci_skip_dev() is therefore
implemented to prevent any such accesses.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Thu, 13 Nov 2014 01:26:48 +0000 (18:26 -0700)]
pci: Abort early if bus does not exist
When listing the devices on a PCI bus, the current code will blindly try
to access all devices. Internally this causes pci_bus_to_hose() to be
repeatedly called and output an error message every time. Prevent this
by calling pci_bus_to_hose() once and abort early if no bus was found.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Thierry Reding [Thu, 13 Nov 2014 01:26:47 +0000 (18:26 -0700)]
vsprintf: Add modifier for phys_addr_t
Provide a new modifier to vsprintf() to print phys_addr_t variables to
avoid having to cast or #ifdef when printing them out. The %pa modifier
is used for this purpose, so phys_addr_t variables need to be passed by
reference, like so:
phys_addr_t start = 0;
printf("start: %pa\n", &start);
Depending on the size of phys_addr_t this will print out the address
with 8 or 16 hexadecimal digits following a 0x prefix.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Christian Gmeiner [Wed, 12 Nov 2014 13:35:04 +0000 (14:35 +0100)]
fs: make it possible to read the filesystem UUID
Some filesystems have a UUID stored in its superblock. To
allow using root=UUID=... for the kernel command line we
need a way to read-out the filesystem UUID.
changes rfc -> v1:
- make the environment variable an option parameter. If not
given, the UUID is printed out. If given, it is stored in the env
variable.
- corrected typos
- return error codes
changes v1 -> v2:
- fix return code of do_fs_uuid(..)
- document do_fs_uuid(..)
- implement fs_uuid_unsuported(..) be more consistent with the
way other optional functionality works
changes v2 -> v3:
- change ext4fs_uuid(..) to make use of #if .. #else .. #endif
construct to get rid of unreachable code
Hit any key to stop autoboot: 0
=> fsuuid
fsuuid - Look up a filesystem UUID
Usage:
fsuuid <interface> <dev>:<part>
- print filesystem UUID
fsuuid <interface> <dev>:<part> <varname>
- set environment variable to filesystem UUID
=> fsuuid mmc 0:1
d9f9fc05-45ae-4a36-a616-
fccce0e4f887
=> fsuuid mmc 0:2
eb3db83c-7b28-499f-95ce-
9e0bb21cda81
=> fsuuid mmc 0:1 uuid1
=> fsuuid mmc 0:2 uuid2
=> printenv uuid1
uuid1=
d9f9fc05-45ae-4a36-a616-
fccce0e4f887
=> printenv uuid2
uuid2=
eb3db83c-7b28-499f-95ce-
9e0bb21cda81
=>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
li pengbo [Wed, 12 Nov 2014 11:16:40 +0000 (19:16 +0800)]
sata: fix a bug in init_sata() for pci-sata card
Except the first loop, init_sata() should return 0 instead of 1
in the others.
This patch fix the issue of the 2nd sata port not workable on pci-sata card.
Signed-off-by: Pengbo Li <Pengbo.Li@freescale.com>
Steve Rae [Tue, 11 Nov 2014 19:32:19 +0000 (11:32 -0800)]
ARM: bcm: Enable bcm11130 boards
bcm11130
bcm11130_nand
Signed-off-by: Steve Rae <srae@broadcom.com>
Steve Rae [Tue, 11 Nov 2014 19:32:18 +0000 (11:32 -0800)]
ARM: bcm: Enable five Cygnus boards
bcm911360_entphn
bcm911360_entphn-ns
bcm911360k
bcm958300k-ns
bcm958305k
- updates to support Cygnus and NSP board families better
- add functions so CONFIG_ARMV7_NONSEC can be enabled on Cygnus boards
Signed-off-by: Steve Rae <srae@broadcom.com>
Stefan Roese [Tue, 11 Nov 2014 18:03:55 +0000 (19:03 +0100)]
spl: Change debug to printf for "Unsupported boot-device"
We had the problem on an AM33xx platform, that SPL detected an
unsupported boot-device. But since this message is a debug message
it took a bit of time to really know, where the hangup in SPL
resulted from. So let's change this debug message to a printf
and also print the detected boot-device that is not supported.
This makes debugging of such cases much easier.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Thu, 6 Nov 2014 18:03:31 +0000 (03:03 +0900)]
linux/kernel.h: sync min, max, min3, max3 macros with Linux
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Masahiro Yamada [Mon, 17 Nov 2014 08:19:41 +0000 (17:19 +0900)]
dm: core: remove unnecessary return condition in uclass lookup
These conditions never happen.
- There is no real uclass with UCLASS_INVALID id.
- uclass never becomes NULL because ll_entry_start() always returns
a valid pointer.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 17 Nov 2014 08:19:40 +0000 (17:19 +0900)]
dm: core: remove unnecessary return condition in driver lookup
The variable "drv" never becomes NULL because ll_entry_start()
always returns a valid pointer even if there are no entries.
The case "n_ents == 0" is covered by the following "for" loop.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 17 Nov 2014 08:19:39 +0000 (17:19 +0900)]
dm: core: remove meaningless if conditional
If the variable "ret" is equal to "-ENOENT", it is trapped at [1] and
never reaches [2]. At [3], the condition "ret != -ENOENT" is always
true.
if (ret == -ENOENT) { <------------------ [1]
continue;
} else if (ret == -ENODEV) {
dm_dbg("Device '%s' has no compatible string\n", name);
break;
} else if (ret) { <------------------ [2]
dm_warn("Device tree error at offset %d\n", offset);
if (!result || ret != -ENOENT) <------------------ [3]
result = ret;
break;
}
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 17 Nov 2014 08:19:38 +0000 (17:19 +0900)]
dm: core: a trivial clean up
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 12 Nov 2014 01:06:30 +0000 (18:06 -0700)]
cros_ec: Fix uninitialised variable in cros_ec.c
This fixes this cppcheck report:
[drivers/misc/cros_ec.c:704]: (error) Uninitialized variable: req
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Wolfgang Denk <wd@denx.de>
Simon Glass [Tue, 11 Nov 2014 17:46:23 +0000 (10:46 -0700)]
dm: spi: Use device_bind_driver() instead of our own function
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Simon Glass [Tue, 11 Nov 2014 17:46:22 +0000 (10:46 -0700)]
dm: spi: Correct handling of SPI chip selects in sandbox
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Simon Glass [Tue, 11 Nov 2014 17:46:21 +0000 (10:46 -0700)]
dm: Add a function to bind a device by driver name
In some cases we need to manually bind a device to a particular driver.
Add a function to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
Simon Glass [Tue, 11 Nov 2014 17:46:20 +0000 (10:46 -0700)]
dm: fdt: Correct handling of aliases with embedded digits
Since we scan from left to right looking for the first digit, "i2c0" returns
2 instead of 0 for the alias number. Adjust the code to scan from right to
left instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 17:46:19 +0000 (10:46 -0700)]
dm: core: Add functions to find parent and OF data
Add dev_get_parent() as a convenience to obtain the parent of a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Simon Glass [Tue, 11 Nov 2014 17:46:18 +0000 (10:46 -0700)]
dm: core: Allow access to the device's driver_id data
When the device is created from a device tree node, it matches a compatible
string. Allow access to that string and the associated data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Fabio Estevam [Thu, 20 Nov 2014 18:35:20 +0000 (16:35 -0200)]
mx53ard: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Thu, 20 Nov 2014 18:35:19 +0000 (16:35 -0200)]
mx53evk: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Thu, 20 Nov 2014 18:35:18 +0000 (16:35 -0200)]
mx53smd: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Thu, 20 Nov 2014 18:35:17 +0000 (16:35 -0200)]
mx6qarm2: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fabio Estevam [Thu, 20 Nov 2014 18:35:16 +0000 (16:35 -0200)]
mx51evk: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Ye.Li [Thu, 20 Nov 2014 13:14:15 +0000 (21:14 +0800)]
mx6: mx6sabre common: Enable i.MX thermal DM driver
Enable i.MX thermal DM driver to mx6sabre_common.h file. Since the
thermal is used in init_sequence_f, so define the CONFIG_SYS_MALLOC_F_LEN
to support DM driver using in pre relocation phase.
Additional, thermal driver depends on ocotp, make sure to enable
CONFIG_MXC_OCOTP when CONFIG_IMX6_THERMAL is selected.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Ye.Li [Thu, 20 Nov 2014 13:14:14 +0000 (21:14 +0800)]
mx6: thermal: Check cpu temperature via thermal sensor
Add imx6 thermal device to mx6 soc file. Read the cpu temperature
using this device to access onchip thermal sensor.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Ye.Li [Thu, 20 Nov 2014 13:14:13 +0000 (21:14 +0800)]
DM: thermal: Add imx thermal DM driver
Add a new thermal uclass for thermal sensor and implement the imx
thermal driver basing on this uclass.
Signed-off-by: Ye.Li <B37916@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Nitin Garg [Thu, 20 Nov 2014 13:14:12 +0000 (21:14 +0800)]
mx6: clock: Add thermal clock enable function
Add api to check and enable pll3 as required
for thermal sensor driver.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Soeren Moch [Thu, 20 Nov 2014 12:03:32 +0000 (13:03 +0100)]
tbs2910: Fix error handling in board_mmc_init()
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Based on similar patches by Fabio Estevam for mx6sabresd, mx53loco, wandboard
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Simon Glass [Tue, 11 Nov 2014 17:46:17 +0000 (10:46 -0700)]
dm: i2c: Move error reporting into a common function
Factor out the common code to make it easier to adjust it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
Simon Glass [Tue, 11 Nov 2014 00:16:54 +0000 (17:16 -0700)]
dm: Update documentation to include CONFIG_DM... options
Add documentation for the various driver model options that are now
available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:52 +0000 (17:16 -0700)]
dm: arm: spl: Make driver model linker lists available
The linker lists feature is useful in SPL as it holds the driver model
platform data. So don't throw away the lists.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 00:16:51 +0000 (17:16 -0700)]
dm: tegra: Add platform data for the GPIO driver
Add platform data for the GPIO driver. It doesn't need to contain anything
since the GPIO driver will actually use information from the CONFIGs for
now. This merely serves to ensure that the GPIO driver is bound.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:50 +0000 (17:16 -0700)]
dm: tegra: Add platform data for the SPL uart
Since we currently don't have device tree available in SPL, add platform
data so the uart works.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:49 +0000 (17:16 -0700)]
dm: Disable dm_warn() in SPL
Since this function can use up quite a bit of space for its strings, disable
it by default in SPL. Use CONFIG_DM_WARN to re-enable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 00:16:48 +0000 (17:16 -0700)]
dm: Allow stdio registration to be dropped
Provide a CONFIG_DM_STDIO option to enable registering a serial device
with the stdio library. This is seldom useful in SPL, so disable it by
default when building for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 00:16:47 +0000 (17:16 -0700)]
dm: Allow device removal features to be dropped
For SPL we don't expect to need to remove a device. Save some code space
by dropping this feature. The board config can define
CONFIG_DM_DEVICE_REMOVE if this is in fact needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 00:16:46 +0000 (17:16 -0700)]
dm: spl: Allow driver model to be used
When enabled, set up driver model for SPL. This allows SPL to use the same
drivers as the main U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 11 Nov 2014 00:16:45 +0000 (17:16 -0700)]
dm: spl: Make simple malloc() available when enabled
Set up the simple malloc() implementation when requested, in preference to
the full malloc().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:44 +0000 (17:16 -0700)]
dm: arm: spl: Allow simple malloc() in SPL
For SPL it is sometimes useful to have a simple malloc() just to permit
driver model to work, in the cases where the full malloc() is not made
available by the board config.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:43 +0000 (17:16 -0700)]
dm: Split the simple malloc() implementation into its own file
The simple malloc() implementation is used when memory is tight. It provides
a simple buffer with an incrementing pointer.
At present the implementation is inside dlmalloc. Move it into its own file
so that it is easier to find.
Rather than using relocation as a signal that the full malloc() is
available, add a special GD_FLG_FULL_MALLOC_INIT flag. This signals that the
simple malloc() should no longer be used.
In some cases, such as SPL, even the code space used by the full malloc() is
wasteful. Add a CONFIG_SYS_MALLOC_SIMPLE option to provide only the simple
malloc. In this case the full malloc is not available at all. It saves about
1KB of code space and about 0.5KB of data on Thumb 2.
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 11 Nov 2014 00:16:42 +0000 (17:16 -0700)]
dm: tegra: Avoid using arch-specific memcpy() in SPL
The faster functions are not actually available in SPL and the code size
likely isn't worth it. Use the normal memcpy() in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:09:03 +0000 (13:09 -0600)]
dm: serial: Support changing the baud rate
Implement this feature in the uclass so that the baudrate can be changed
with 'setenv baudrate <rate>'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:09:02 +0000 (13:09 -0600)]
dm: at91: Add myself as maintainer for snapper9260
The old maintainer has left, so take this over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:09:01 +0000 (13:09 -0600)]
dm: at91: Convert snapper9260 to use driver model
Convert this at91sam9260-based board to use driver model. This should serve
as an example for other similar boards. Serial and GPIO are supported so
far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Simon Glass [Wed, 29 Oct 2014 19:09:00 +0000 (13:09 -0600)]
dm: at91: Add driver model support for the serial driver
Add driver model support while retaining the existing legacy code. This
allows the driver to support boards that have converted to driver model
as well as those that have not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:59 +0000 (13:08 -0600)]
dm: at91: Refactor serial driver slightly for driver model
Before adding driver model support, split out a few of the functions so
that they can be used by the driver model code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Simon Glass [Wed, 29 Oct 2014 19:08:58 +0000 (13:08 -0600)]
dm: at91: Add platform data for GPIO on at91sam9260-based boards
These boards all have the same GPIO arrangement, so add some common platform
data that can be used by all boards. Remove the configs which are no longer
required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:57 +0000 (13:08 -0600)]
dm: at91: Add driver model support for atmel GPIO driver
Modify this driver to support driver model, with platform data required to
determine the GPIOs that it controls.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:56 +0000 (13:08 -0600)]
dm: at91: Move snapper9260 to generic baord
This works correctly, so switch it over before the deadline.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Wed, 29 Oct 2014 19:08:55 +0000 (13:08 -0600)]
dm: at91: Correct text base for snapper9260
The value should be 0x21f00000. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>