Michal Simek [Tue, 25 Sep 2018 06:32:50 +0000 (08:32 +0200)]
net: macb: Clean 64b dma addresses if they are not detected
[ Upstream commit
e1e5d8a9fe737d94ccc0ccbaf0c97f69a8f3e000 ]
Clear ADDR64 dma bit in DMACFG register in case that HW_DMA_CAP_64B is
not detected on 64bit system.
The issue was observed when bootloader(u-boot) does not check macb
feature at DCFG6 register (DAW64_OFFSET) and enabling 64bit dma support
by default. Then macb driver is reading DMACFG register back and only
adding 64bit dma configuration but not cleaning it out.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Florian Fainelli [Thu, 20 Sep 2018 00:14:01 +0000 (17:14 -0700)]
ARM: dts: BCM63xx: Fix incorrect interrupt specifiers
[ Upstream commit
3ab97942d0213b6583a5408630a8cbbfbf54730f ]
A number of our interrupts were incorrectly specified, fix both the PPI
and SPI interrupts to be correct.
Fixes:
b5762cacc411 ("ARM: bcm63138: add NAND DT support")
Fixes:
46d4bca0445a ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steve Capper [Fri, 21 Sep 2018 15:34:04 +0000 (16:34 +0100)]
arm64: hugetlb: Fix handling of young ptes
[ Upstream commit
469ed9d823b7d240d6b9574f061ded7c3834c167 ]
In the contiguous bit hugetlb break-before-make code we assume that all
hugetlb pages are young.
In fact, remove_migration_pte is able to place an old hugetlb pte so
this assumption is not valid.
This patch fixes the contiguous hugetlb scanning code to preserve young
ptes.
Fixes:
d8bdcff28764 ("arm64: hugetlb: Add break-before-make logic for contiguous entries")
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
David Ahern [Mon, 17 Sep 2018 15:20:36 +0000 (08:20 -0700)]
netfilter: bridge: Don't sabotage nf_hook calls from an l3mdev
[ Upstream commit
a173f066c7cfc031acb8f541708041e009fc9812 ]
For starters, the bridge netfilter code registers operations that
are invoked any time nh_hook is called. Specifically, ip_sabotage_in
watches for nested calls for NF_INET_PRE_ROUTING when a bridge is in
the stack.
Packet wise, the bridge netfilter hook runs first. br_nf_pre_routing
allocates nf_bridge, sets in_prerouting to 1 and calls NF_HOOK for
NF_INET_PRE_ROUTING. It's finish function, br_nf_pre_routing_finish,
then resets in_prerouting flag to 0 and the packet continues up the
stack. The packet eventually makes it to the VRF driver and it invokes
nf_hook for NF_INET_PRE_ROUTING in case any rules have been added against
the vrf device.
Because of the registered operations the call to nf_hook causes
ip_sabotage_in to be invoked. That function sees the nf_bridge on the
skb and that in_prerouting is not set. Thinking it is an invalid nested
call it steals (drops) the packet.
Update ip_sabotage_in to recognize that the bridge or one of its upper
devices (e.g., vlan) can be enslaved to a VRF (L3 master device) and
allow the packet to go through the nf_hook a second time.
Fixes:
73e20b761acf ("net: vrf: Add support for PREROUTING rules on vrf device")
Reported-by: D'Souza, Nelson <ndsouza@ciena.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sean Tranchetti [Wed, 19 Sep 2018 19:54:56 +0000 (13:54 -0600)]
xfrm: validate template mode
[ Upstream commit
32bf94fb5c2ec4ec842152d0e5937cd4bb6738fa ]
XFRM mode parameters passed as part of the user templates
in the IP_XFRM_POLICY are never properly validated. Passing
values other than valid XFRM modes can cause stack-out-of-bounds
reads to occur later in the XFRM processing:
[ 140.535608] ================================================================
[ 140.543058] BUG: KASAN: stack-out-of-bounds in xfrm_state_find+0x17e4/0x1cc4
[ 140.550306] Read of size 4 at addr
ffffffc0238a7a58 by task repro/5148
[ 140.557369]
[ 140.558927] Call trace:
[ 140.558936] dump_backtrace+0x0/0x388
[ 140.558940] show_stack+0x24/0x30
[ 140.558946] __dump_stack+0x24/0x2c
[ 140.558949] dump_stack+0x8c/0xd0
[ 140.558956] print_address_description+0x74/0x234
[ 140.558960] kasan_report+0x240/0x264
[ 140.558963] __asan_report_load4_noabort+0x2c/0x38
[ 140.558967] xfrm_state_find+0x17e4/0x1cc4
[ 140.558971] xfrm_resolve_and_create_bundle+0x40c/0x1fb8
[ 140.558975] xfrm_lookup+0x238/0x1444
[ 140.558977] xfrm_lookup_route+0x48/0x11c
[ 140.558984] ip_route_output_flow+0x88/0xc4
[ 140.558991] raw_sendmsg+0xa74/0x266c
[ 140.558996] inet_sendmsg+0x258/0x3b0
[ 140.559002] sock_sendmsg+0xbc/0xec
[ 140.559005] SyS_sendto+0x3a8/0x5a8
[ 140.559008] el0_svc_naked+0x34/0x38
[ 140.559009]
[ 140.592245] page dumped because: kasan: bad access detected
[ 140.597981] page_owner info is not active (free page?)
[ 140.603267]
[ 140.653503] ================================================================
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas Petazzoni [Thu, 13 Sep 2018 15:48:08 +0000 (16:48 +0100)]
ARM: 8799/1: mm: fix pci_ioremap_io() offset check
[ Upstream commit
3a58ac65e2d7969bcdf1b6acb70fa4d12a88e53e ]
IO_SPACE_LIMIT is the ending address of the PCI IO space, i.e
something like 0xfffff (and not 0x100000).
Therefore, when offset = 0xf0000 is passed as argument, this function
fails even though the offset + SZ_64K fits below the
IO_SPACE_LIMIT. This makes the last chunk of 64 KB of the I/O space
not usable as it cannot be mapped.
This patch fixes that by substracing 1 to offset + SZ_64K, so that we
compare the addrss of the last byte of the I/O space against
IO_SPACE_LIMIT instead of the address of the first byte of what is
after the I/O space.
Fixes:
c2794437091a4 ("ARM: Add fixed PCI i/o mapping")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steffen Klassert [Tue, 11 Sep 2018 08:31:15 +0000 (10:31 +0200)]
xfrm: Fix NULL pointer dereference when skb_dst_force clears the dst_entry.
[ Upstream commit
9e1437937807b0122e8da1ca8765be2adca9aee6 ]
Since commit
222d7dbd258d ("net: prevent dst uses after free")
skb_dst_force() might clear the dst_entry attached to the skb.
The xfrm code don't expect this to happen, so we crash with
a NULL pointer dereference in this case. Fix it by checking
skb_dst(skb) for NULL after skb_dst_force() and drop the packet
in cast the dst_entry was cleared.
Fixes:
222d7dbd258d ("net: prevent dst uses after free")
Reported-by: Tobias Hommel <netdev-list@genoetigt.de>
Reported-by: Kristian Evensen <kristian.evensen@gmail.com>
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Yuan-Chi Pang [Thu, 6 Sep 2018 08:57:48 +0000 (16:57 +0800)]
mac80211: fix TX status reporting for ieee80211s
[ Upstream commit
c42055105785580563535e6d3143cad95c7ac7ee ]
TX status reporting to ieee80211s is through ieee80211s_update_metric.
There are two problems about ieee80211s_update_metric:
1. The purpose is to estimate the fail probability
to a specific link. No need to restrict to data frame.
2. Current implementation does not work if wireless driver does not
pass tx_status with skb.
Fix this by removing ieee80211_is_data condition, passing
ieee80211_tx_status directly to ieee80211s_update_metric, and
putting it in both __ieee80211_tx_status and ieee80211_tx_status_ext.
Signed-off-by: Yuan-Chi Pang <fu3mo6goo@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Johannes Berg [Wed, 5 Sep 2018 11:34:02 +0000 (13:34 +0200)]
mac80211: TDLS: fix skb queue/priority assignment
[ Upstream commit
cb59bc14e830028d2244861216df038165d7625d ]
If the TDLS setup happens over a connection to an AP that
doesn't have QoS, we nevertheless assign a non-zero TID
(skb->priority) and queue mapping, which may confuse us or
drivers later.
Fix it by just assigning the special skb->priority and then
using ieee80211_select_queue() just like other data frames
would go through.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Jouni Malinen [Wed, 5 Sep 2018 15:52:22 +0000 (18:52 +0300)]
cfg80211: Address some corner cases in scan result channel updating
[ Upstream commit
119f94a6fefcc76d47075b83d2b73d04c895df78 ]
cfg80211_get_bss_channel() is used to update the RX channel based on the
available frame payload information (channel number from DSSS Parameter
Set element or HT Operation element). This is needed on 2.4 GHz channels
where frames may be received on neighboring channels due to overlapping
frequency range.
This might of some use on the 5 GHz band in some corner cases, but
things are more complex there since there is no n:1 or 1:n mapping
between channel numbers and frequencies due to multiple different
starting frequencies in different operating classes. This could result
in ieee80211_channel_to_frequency() returning incorrect frequency and
ieee80211_get_channel() returning incorrect channel information (or
indication of no match). In the previous implementation, this could
result in some scan results being dropped completely, e.g., for the 4.9
GHz channels. That prevented connection to such BSSs.
Fix this by using the driver-provided channel pointer if
ieee80211_get_channel() does not find matching channel data for the
channel number in the frame payload and if the scan is done with 5 MHz
or 10 MHz channel bandwidth. While doing this, also add comments
describing what the function is trying to achieve to make it easier to
understand what happens here and why.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Bob Copeland [Wed, 5 Sep 2018 10:22:59 +0000 (06:22 -0400)]
mac80211: fix pending queue hang due to TX_DROP
[ Upstream commit
6eae4a6c2be387fec41b0d2782c4fffb57159498 ]
In our environment running lots of mesh nodes, we are seeing the
pending queue hang periodically, with the debugfs queues file showing
lines such as:
00: 0x00000000/348
i.e. there are a large number of frames but no stop reason set.
One way this could happen is if queue processing from the pending
tasklet exited early without processing all frames, and without having
some future event (incoming frame, stop reason flag, ...) to reschedule
it.
Exactly this can occur today if ieee80211_tx() returns false due to
packet drops or power-save buffering in the tx handlers. In the
past, this function would return true in such cases, and the change
to false doesn't seem to be intentional. Fix this case by reverting
to the previous behavior.
Fixes:
bb42f2d13ffc ("mac80211: Move reorder-sensitive TX handlers to after TXQ dequeue")
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrei Otcheretianski [Wed, 5 Sep 2018 05:06:12 +0000 (08:06 +0300)]
cfg80211: reg: Init wiphy_idx in regulatory_hint_core()
[ Upstream commit
24f33e64fcd0d50a4b1a8e5b41bd0257aa66b0e8 ]
Core regulatory hints didn't set wiphy_idx to WIPHY_IDX_INVALID. Since
the regulatory request is zeroed, wiphy_idx was always implicitly set to
0. This resulted in updating only phy #0.
Fix that.
Fixes:
806a9e39670b ("cfg80211: make regulatory_request use wiphy_idx instead of wiphy")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[add fixes tag]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Andrei Otcheretianski [Wed, 5 Sep 2018 05:06:13 +0000 (08:06 +0300)]
mac80211: Always report TX status
[ Upstream commit
8682250b3c1b75a45feb7452bc413d004cfe3778 ]
If a frame is dropped for any reason, mac80211 wouldn't report the TX
status back to user space.
As the user space may rely on the TX_STATUS to kick its state
machines, resends etc, it's better to just report this frame as not
acked instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sowmini Varadhan [Mon, 3 Sep 2018 11:36:53 +0000 (04:36 -0700)]
xfrm: reset crypto_done when iterating over multiple input xfrms
[ Upstream commit
782710e333a526780d65918d669cb96646983ba2 ]
We only support one offloaded xfrm (we do not have devices that
can handle more than one offload), so reset crypto_done in
xfrm_input() when iterating over multiple transforms in xfrm_input,
so that we can invoke the appropriate x->type->input for the
non-offloaded transforms
Fixes:
d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Sowmini Varadhan [Mon, 3 Sep 2018 11:36:52 +0000 (04:36 -0700)]
xfrm: reset transport header back to network header after all input transforms ahave been applied
[ Upstream commit
bfc0698bebcb16d19ecfc89574ad4d696955e5d3 ]
A policy may have been set up with multiple transforms (e.g., ESP
and ipcomp). In this situation, the ingress IPsec processing
iterates in xfrm_input() and applies each transform in turn,
processing the nexthdr to find any additional xfrm that may apply.
This patch resets the transport header back to network header
only after the last transformation so that subsequent xfrms
can find the correct transport header.
Fixes:
7785bba299a8 ("esp: Add a software GRO codepath")
Suggested-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Thadeu Lima de Souza Cascardo [Fri, 31 Aug 2018 11:38:49 +0000 (08:38 -0300)]
xfrm6: call kfree_skb when skb is toobig
[ Upstream commit
215ab0f021c9fea3c18b75e7d522400ee6a49990 ]
After commit
d6990976af7c5d8f55903bfb4289b6fb030bf754 ("vti6: fix PMTU caching
and reporting on xmit"), some too big skbs might be potentially passed down to
__xfrm6_output, causing it to fail to transmit but not free the skb, causing a
leak of skb, and consequentially a leak of dst references.
After running pmtu.sh, that shows as failure to unregister devices in a namespace:
[ 311.397671] unregister_netdevice: waiting for veth_b to become free. Usage count = 1
The fix is to call kfree_skb in case of transmit failures.
Fixes:
dd767856a36e ("xfrm6: Don't call icmpv6_send on local error")
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Steffen Klassert [Wed, 1 Aug 2018 11:45:11 +0000 (13:45 +0200)]
xfrm: Validate address prefix lengths in the xfrm selector.
[ Upstream commit
07bf7908950a8b14e81aa1807e3c667eab39287a ]
We don't validate the address prefix lengths in the xfrm
selector we got from userspace. This can lead to undefined
behaviour in the address matching functions if the prefix
is too big for the given address family. Fix this by checking
the prefixes and refuse SA/policy insertation when a prefix
is invalid.
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Air Icy <icytxw@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Greg Kroah-Hartman [Sat, 20 Oct 2018 07:48:54 +0000 (09:48 +0200)]
Linux 4.14.78
Michael J. Ruhl [Thu, 20 Sep 2018 19:59:14 +0000 (12:59 -0700)]
IB/hfi1: Fix destroy_qp hang after a link down
commit
b4a4957d3d1c328b733fce783b7264996f866ad2 upstream.
rvt_destroy_qp() cannot complete until all in process packets have
been released from the underlying hardware. If a link down event
occurs, an application can hang with a kernel stack similar to:
cat /proc/<app PID>/stack
quiesce_qp+0x178/0x250 [hfi1]
rvt_reset_qp+0x23d/0x400 [rdmavt]
rvt_destroy_qp+0x69/0x210 [rdmavt]
ib_destroy_qp+0xba/0x1c0 [ib_core]
nvme_rdma_destroy_queue_ib+0x46/0x80 [nvme_rdma]
nvme_rdma_free_queue+0x3c/0xd0 [nvme_rdma]
nvme_rdma_destroy_io_queues+0x88/0xd0 [nvme_rdma]
nvme_rdma_error_recovery_work+0x52/0xf0 [nvme_rdma]
process_one_work+0x17a/0x440
worker_thread+0x126/0x3c0
kthread+0xcf/0xe0
ret_from_fork+0x58/0x90
0xffffffffffffffff
quiesce_qp() waits until all outstanding packets have been freed.
This wait should be momentary. During a link down event, the cleanup
handling does not ensure that all packets caught by the link down are
flushed properly.
This is caused by the fact that the freeze path and the link down
event is handled the same. This is not correct. The freeze path
waits until the HFI is unfrozen and then restarts PIO. A link down
is not a freeze event. The link down path cannot restart the PIO
until link is restored. If the PIO path is restarted before the link
comes up, the application (QP) using the PIO path will hang (until
link is restored).
Fix by separating the linkdown path from the freeze path and use the
link down path for link down events.
Close a race condition sc_disable() by acquiring both the progress
and release locks.
Close a race condition in sc_stop() by moving the setting of the flag
bits under the alloc lock.
Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes:
7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Thu, 28 Jun 2018 20:45:38 +0000 (22:45 +0200)]
i2c: rcar: handle RXDMA HW behaviour on Gen3
commit
2b16fd63059ab9a46d473620749672dc342e1d21 upstream.
On Gen3, we can only do RXDMA once per transfer reliably. For that, we
must reset the device, then we can have RXDMA once. This patch
implements this. When there is no reset controller or the reset fails,
RXDMA will be blocked completely. Otherwise, it will be disabled after
the first RXDMA transfer. Based on a commit from the BSP by Hiromitsu
Yamasaki, yet completely refactored to handle multiple read messages
within one transfer.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clint Taylor [Tue, 10 Jul 2018 20:02:05 +0000 (13:02 -0700)]
drm/i915/glk: Add Quirk for GLK NUC HDMI port issues.
commit
0ca9488193e61ec5f31a631d8147f74525629e8a upstream.
On GLK NUC platforms the HDMI retiming buffer needs additional disabled
time to correctly sync to a faster incoming signal.
When measured on a scope the highspeed lines of the HDMI clock turn off
for ~400uS during a normal resolution change. The HDMI retimer on the
GLK NUC appears to require at least a full frame of quiet time before a
new faster clock can be correctly sync'd. Wait 100ms due to msleep
inaccuracies while waiting for a completed frame. Add a quirk to the
driver for GLK boards that use ITE66317 HDMI retimers.
V2: Add more devices to the quirk list
V3: Delay increased to 100ms, check to confirm crtc type is HDMI.
V4: crtc type check extended to include _DDI and whitespace fixes
v5: Fix white spaces, remove the macro for delay. Revert the crtc type
check introduced in v4.
Cc: Imre Deak <imre.deak@intel.com>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105887
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Tested-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710200205.1478-1-radhakrishna.sripada@intel.com
(cherry picked from commit
90c3e2198777aaa355b6994a31a79c636c8d4306)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Jiang [Thu, 26 Jul 2018 23:37:15 +0000 (16:37 -0700)]
mm: disallow mappings that conflict for devm_memremap_pages()
commit
15d36fecd0bdc7510b70a0e5ec6671140b3fce0c upstream.
When pmem namespaces created are smaller than section size, this can
cause an issue during removal and gpf was observed:
general protection fault: 0000 1 SMP PTI
CPU: 36 PID: 3941 Comm: ndctl Tainted: G W 4.14.28-1.el7uek.x86_64 #2
task:
ffff88acda150000 task.stack:
ffffc900233a4000
RIP: 0010:__put_page+0x56/0x79
Call Trace:
devm_memremap_pages_release+0x155/0x23a
release_nodes+0x21e/0x260
devres_release_all+0x3c/0x48
device_release_driver_internal+0x15c/0x207
device_release_driver+0x12/0x14
unbind_store+0xba/0xd8
drv_attr_store+0x27/0x31
sysfs_kf_write+0x3f/0x46
kernfs_fop_write+0x10f/0x18b
__vfs_write+0x3a/0x16d
vfs_write+0xb2/0x1a1
SyS_write+0x55/0xb9
do_syscall_64+0x79/0x1ae
entry_SYSCALL_64_after_hwframe+0x3d/0x0
Add code to check whether we have a mapping already in the same section
and prevent additional mappings from being created if that is the case.
Link: http://lkml.kernel.org/r/152909478401.50143.312364396244072931.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Robert Elliott <elliott@hpe.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gilad Ben-Yossef [Sun, 7 Jan 2018 12:14:24 +0000 (12:14 +0000)]
staging: ccree: check DMA pool buf !NULL before free
commit
2f7caf6b02145bd9cd9d0b56204f51a5fefe7790 upstream.
If we ran out of DMA pool buffers, we get into the unmap
code path with a NULL before. Deal with this by checking
the virtual mapping is not NULL.
Cc: stable@vger.kernel.org
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ville Syrjälä [Tue, 17 Jul 2018 17:42:14 +0000 (20:42 +0300)]
drm/i915: Nuke the LVDS lid notifier
commit
05c72e77ccda89ff624108b1b59a0fc43843f343 upstream.
We broke the LVDS notifier resume thing in (presumably) commit
e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.") as
we no longer duplicate the current state in the LVDS notifier and
thus we never resume it properly either.
Instead of trying to fix it again let's just kill off the lid
notifier entirely. None of the machines tested thus far have
apparently needed it. Originally the lid notifier was added to
work around cases where the VBIOS was clobbering some of the
hardware state behind the driver's back, mostly on Thinkpads.
We now have a few report of Thinkpads working just fine without
the notifier. So maybe it was misdiagnosed originally, or
something else has changed (ACPI video stuff perhaps?).
If we do end up finding a machine where the VBIOS is still causing
problems I would suggest that we first try setting various bits in
the VBIOS scratch registers. There are several to choose from that
may instruct the VBIOS to steer clear.
With the notifier gone we'll also stop looking at the panel status
in ->detect().
v2: Nuke enum modeset_restore (Rodrigo)
Cc: stable@vger.kernel.org
Cc: Wolfgang Draxinger <wdraxinger.maillist@draxit.de>
Cc: Vito Caputo <vcaputo@pengaru.com>
Cc: kitsunyan <kitsunyan@airmail.cc>
Cc: Joonas Saarinen <jza@saunalahti.fi>
Tested-by: Vito Caputo <vcaputo@pengaru.com> # Thinkapd X61s
Tested-by: kitsunyan <kitsunyan@airmail.cc> # ThinkPad X200
Tested-by: Joonas Saarinen <jza@saunalahti.fi> # Fujitsu Siemens U9210
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105902
References: https://lists.freedesktop.org/archives/intel-gfx/2018-June/169315.html
References: https://bugs.freedesktop.org/show_bug.cgi?id=21230
Fixes:
e2c8b8701e2d ("drm/i915: Use atomic helpers for suspend, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717174216.22252-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Natanael Copa [Thu, 18 Oct 2018 15:04:17 +0000 (17:04 +0200)]
HID: quirks: fix support for Apple Magic Keyboards
Commit
b6cc0ba2cbf4 (HID: add support for Apple Magic Keyboards)
backported support for the Magic Keyboard over Bluetooth, but did not
add the BT_VENDOR_ID_APPLE to hid_have_special_driver[] so the hid-apple
driver is never loaded and Fn key does not work at all.
Adding BT_VENDOR_ID_APPLE to hid_have_special_driver[] is not needed
after commit
e04a0442d33b (HID: core: remove the absolute need of
hid_have_special_driver[]), so 4.16 kernels and newer does not need it.
Fixes:
b6cc0ba2cbf4 (HID: add support for Apple Magic Keyboards)
Bugzilla-id: https://bugzilla.kernel.org/show_bug.cgi?id=99881
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Brodkin [Sun, 16 Sep 2018 20:47:57 +0000 (23:47 +0300)]
ARC: build: Don't set CROSS_COMPILE in arch's Makefile
commit
40660f1fcee8d524a60b5101538e42b1f39f106d upstream.
There's not much sense in doing that because if user or
his build-system didn't set CROSS_COMPILE we still may
very well make incorrect guess.
But as it turned out setting CROSS_COMPILE is not as harmless
as one may think: with recent changes that implemented automatic
discovery of __host__ gcc features unconditional setup of
CROSS_COMPILE leads to failures on execution of "make xxx_defconfig"
with absent cross-compiler, for more info see [1].
Set CROSS_COMPILE as well gets in the way if we want only to build
.dtb's (again with absent cross-compiler which is not really needed
for building .dtb's), see [2].
Note, we had to change LIBGCC assignment type from ":=" to "="
so that is is resolved on its usage, otherwise if it is resolved
at declaration time with missing CROSS_COMPILE we're getting this
error message from host GCC:
| gcc: error: unrecognized command line option -mmedium-calls
| gcc: error: unrecognized command line option -mno-sdata
[1] http://lists.infradead.org/pipermail/linux-snps-arc/2018-September/004308.html
[2] http://lists.infradead.org/pipermail/linux-snps-arc/2018-September/004320.html
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexey Brodkin [Thu, 13 Sep 2018 20:24:28 +0000 (23:24 +0300)]
ARC: build: Get rid of toolchain check
commit
615f64458ad890ef94abc879a66d8b27236e733a upstream.
This check is very naive: we simply test if GCC invoked without
"-mcpu=XXX" has ARC700 define set. In that case we think that GCC
was built with "--with-cpu=arc700" and has libgcc built for ARC700.
Otherwise if ARC700 is not defined we think that everythng was built
for ARCv2.
But in reality our life is much more interesting.
1. Regardless of GCC configuration (i.e. what we pass in "--with-cpu"
it may generate code for any ARC core).
2. libgcc might be built with explicitly specified "--mcpu=YYY"
That's exactly what happens in case of multilibbed toolchains:
- GCC is configured with default settings
- All the libs built for many different CPU flavors
I.e. that check gets in the way of usage of multilibbed
toolchains. And even non-multilibbed toolchains are affected.
OpenEmbedded also builds GCC without "--with-cpu" because
each and every target component later is compiled with explicitly
set "-mcpu=ZZZ".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 12 Oct 2018 22:22:59 +0000 (15:22 -0700)]
mremap: properly flush TLB before releasing the page
commit
eb66ae030829605d61fbef1909ce310e29f78821 upstream.
Jann Horn points out that our TLB flushing was subtly wrong for the
mremap() case. What makes mremap() special is that we don't follow the
usual "add page to list of pages to be freed, then flush tlb, and then
free pages". No, mremap() obviously just _moves_ the page from one page
table location to another.
That matters, because mremap() thus doesn't directly control the
lifetime of the moved page with a freelist: instead, the lifetime of the
page is controlled by the page table locking, that serializes access to
the entry.
As a result, we need to flush the TLB not just before releasing the lock
for the source location (to avoid any concurrent accesses to the entry),
but also before we release the destination page table lock (to avoid the
TLB being flushed after somebody else has already done something to that
page).
This also makes the whole "need_flush" logic unnecessary, since we now
always end up flushing the TLB for every valid entry.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 18 Oct 2018 12:22:54 +0000 (14:22 +0200)]
Revert "vfs: fix freeze protection in mnt_want_write_file() for overlayfs"
This reverts commit
4f4374a9bd25b333971e6f2656b642d29e2efe7b which was
commit
a6795a585929d94ca3e931bc8518f8deb8bbe627 upstream.
Turns out this causes problems and was to fix a patch only in the 4.19
and newer tree.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Cc: Miklos Szeredi <mszeredi@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christophe Leroy [Fri, 24 Nov 2017 07:31:09 +0000 (08:31 +0100)]
powerpc/lib/feature-fixups: use raw_patch_instruction()
commit
8183d99f4a22c2abbc543847a588df3666ef0c0c upstream.
feature fixups need to use patch_instruction() early in the boot,
even before the code is relocated to its final address, requiring
patch_instruction() to use PTRRELOC() in order to address data.
But feature fixups applies on code before it is set to read only,
even for modules. Therefore, feature fixups can use
raw_patch_instruction() instead.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: David Gounaris <david.gounaris@infinera.com>
Tested-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arindam Nath [Tue, 18 Sep 2018 10:10:58 +0000 (15:40 +0530)]
iommu/amd: Return devid as alias for ACPI HID devices
[ Upstream commit
5ebb1bc2d63d90dd204169e21fd7a0b4bb8c776e ]
ACPI HID devices do not actually have an alias for
them in the IVRS. But dev_data->alias is still used
for indexing into the IOMMU device table for devices
being handled by the IOMMU. So for ACPI HID devices,
we simply return the corresponding devid as an alias,
as parsed from IVRS table.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Fixes:
2bf9a0a12749 ('iommu/amd: Add iommu support for ACPI HID devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Neuling [Tue, 25 Sep 2018 09:36:47 +0000 (19:36 +1000)]
powerpc/tm: Avoid possible userspace r1 corruption on reclaim
[ Upstream commit
96dc89d526ef77604376f06220e3d2931a0bfd58 ]
Current we store the userspace r1 to PACATMSCRATCH before finally
saving it to the thread struct.
In theory an exception could be taken here (like a machine check or
SLB miss) that could write PACATMSCRATCH and hence corrupt the
userspace r1. The SLB fault currently doesn't touch PACATMSCRATCH, but
others do.
We've never actually seen this happen but it's theoretically
possible. Either way, the code is fragile as it is.
This patch saves r1 to the kernel stack (which can't fault) before we
turn MSR[RI] back on. PACATMSCRATCH is still used but only with
MSR[RI] off. We then copy r1 from the kernel stack to the thread
struct once we have MSR[RI] back on.
Suggested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Neuling [Mon, 24 Sep 2018 07:27:04 +0000 (17:27 +1000)]
powerpc/tm: Fix userspace r13 corruption
[ Upstream commit
cf13435b730a502e814c63c84d93db131e563f5f ]
When we treclaim we store the userspace checkpointed r13 to a scratch
SPR and then later save the scratch SPR to the user thread struct.
Unfortunately, this doesn't work as accessing the user thread struct
can take an SLB fault and the SLB fault handler will write the same
scratch SPRG that now contains the userspace r13.
To fix this, we store r13 to the kernel stack (which can't fault)
before we access the user thread struct.
Found by running P8 guest + powervm + disable_1tb_segments + TM. Seen
as a random userspace segfault with r13 looking like a kernel address.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tao Ren [Wed, 19 Sep 2018 22:13:31 +0000 (15:13 -0700)]
clocksource/drivers/fttmr010: Fix set_next_event handler
[ Upstream commit
4451d3f59f2a6f95e5d205c2d04ea072955d080d ]
Currently, the aspeed MATCH1 register is updated to <current_count -
cycles> in set_next_event handler, with the assumption that COUNT
register value is preserved when the timer is disabled and it continues
decrementing after the timer is enabled. But the assumption is wrong:
RELOAD register is loaded into COUNT register when the aspeed timer is
enabled, which means the next event may be delayed because timer
interrupt won't be generated until <0xFFFFFFFF - current_count +
cycles>.
The problem can be fixed by updating RELOAD register to <cycles>, and
COUNT register will be re-loaded when the timer is enabled and interrupt
is generated when COUNT register overflows.
The test result on Facebook Backpack-CMM BMC hardware (AST2500) shows
the issue is fixed: without the patch, usleep(100) suspends the process
for several milliseconds (and sometimes even over 40 milliseconds);
after applying the fix, usleep(100) takes averagely 240 microseconds to
return under the same workload level.
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nathan Chancellor [Fri, 21 Sep 2018 09:44:12 +0000 (02:44 -0700)]
net/mlx4: Use cpumask_available for eq->affinity_mask
[ Upstream commit
8ac1ee6f4d62e781e3b3fd8b9c42b70371427669 ]
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/net/ethernet/mellanox/mlx4/eq.c:243:11: warning: address of
array 'eq->affinity_mask' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (!eq->affinity_mask || cpumask_empty(eq->affinity_mask))
~~~~~^~~~~~~~~~~~~
1 warning generated.
Use cpumask_available, introduced in commit
f7e30f01a9e2 ("cpumask: Add
helper cpumask_available()"), which does the proper checking and avoids
this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/86
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johannes Thumshirn [Fri, 21 Sep 2018 07:01:01 +0000 (09:01 +0200)]
scsi: sd: don't crash the host on invalid commands
[ Upstream commit
f1f1fadacaf08b7cf11714c0c29f8fa4d4ef68a9 ]
When sd_init_command() get's a command with a unknown req_op() it crashes the
system via BUG().
This makes debugging the actual reason for the broken request cmd_flags pretty
hard as the system is down before it's able to write out debugging data on the
serial console or the trace buffer.
Change the BUG() to a WARN_ON() and return BLKPREP_KILL to fail gracefully and
return an I/O error to the producer of the request.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wen Xiong [Fri, 21 Sep 2018 00:32:12 +0000 (19:32 -0500)]
scsi: ipr: System hung while dlpar adding primary ipr adapter back
[ Upstream commit
318ddb34b2052f838aa243d07173e2badf3e630e ]
While dlpar adding primary ipr adapter back, driver goes through adapter
initialization then schedule ipr_worker_thread to start te disk scan by
dropping the host lock, calling scsi_add_device. Then get the adapter reset
request again, so driver does scsi_block_requests, this will cause the
scsi_add_device get hung until we unblock. But we can't run ipr_worker_thread
to do the unblock because its stuck in scsi_add_device.
This patch fixes the issue.
[mkp: typo and whitespace fixes]
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexandru Gheorghe [Mon, 16 Jul 2018 10:07:07 +0000 (11:07 +0100)]
drm: mali-dp: Call drm_crtc_vblank_reset on device init
[ Upstream commit
69be1984ded00a11b1ed0888c6d8e4f35370372f ]
Currently, if userspace calls drm_wait_vblank before the crtc is
activated the crtc vblank_enable hook is called, which in case of
malidp driver triggers some warninngs. This happens because on
device init we don't inform the drm core about the vblank state
by calling drm_crtc_vblank_on/off/reset which together with
drm_vblank_get have some magic that prevents calling drm_vblank_enable
when crtc is off.
Signed-off-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jisheng Zhang [Thu, 20 Sep 2018 21:32:52 +0000 (16:32 -0500)]
PCI: dwc: Fix scheduling while atomic issues
[ Upstream commit
9024143e700f89d74b8cdaf316a3499d74fc56fe ]
When programming the inbound/outbound ATUs, we call usleep_range() after
each checking PCIE_ATU_ENABLE bit. Unfortunately, the ATU programming
can be executed in atomic context:
inbound ATU programming could be called through
pci_epc_write_header()
=>dw_pcie_ep_write_header()
=>dw_pcie_prog_inbound_atu()
outbound ATU programming could be called through
pci_bus_read_config_dword()
=>dw_pcie_rd_conf()
=>dw_pcie_prog_outbound_atu()
Fix this issue by calling mdelay() instead.
Fixes:
f8aed6ec624f ("PCI: dwc: designware: Add EP mode support")
Fixes:
d8bbeb39fbf3 ("PCI: designware: Wait for iATU enable")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
[lorenzo.pieralisi@arm.com: commit log update]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kazuya Mizuguchi [Tue, 18 Sep 2018 10:22:26 +0000 (12:22 +0200)]
ravb: do not write 1 to reserved bits
[ Upstream commit
2fe397a3959de8a472f165e6d152f64cb77fa2cc ]
EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Lamparter [Mon, 17 Sep 2018 15:22:40 +0000 (17:22 +0200)]
net: emac: fix fixed-link setup for the RTL8363SB switch
[ Upstream commit
08e39982ef64f800fd1f9b9b92968d14d5fafa82 ]
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Schmitz [Mon, 17 Sep 2018 22:27:49 +0000 (15:27 -0700)]
Input: atakbd - fix Atari CapsLock behaviour
[ Upstream commit
52d2c7bf7c90217fbe875d2d76f310979c48eb83 ]
The CapsLock key on Atari keyboards is not a toggle, it does send the
normal make and break scancodes.
Drop the CapsLock toggle handling code, which did cause the CapsLock
key to merely act as a Shift key.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Schwab [Mon, 17 Sep 2018 19:43:34 +0000 (12:43 -0700)]
Input: atakbd - fix Atari keymap
[ Upstream commit
9e62df51be993035c577371ffee5477697a56aad ]
Fix errors in Atari keymap (mostly in keypad, help and undo keys).
Patch provided on debian-68k ML by Andreas Schwab <schwab@linux-m68k.org>,
keymap array size and unhandled scancode limit adjusted to 0x73 by me.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander Shishkin [Tue, 18 Sep 2018 13:10:49 +0000 (16:10 +0300)]
intel_th: pci: Add Ice Lake PCH support
[ Upstream commit
59d08d00d43c644ee2011d7ff1807bdd69f31fe0 ]
This adds Intel(R) Trace Hub PCI ID for Ice Lake PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laura Abbott [Tue, 11 Sep 2018 19:22:26 +0000 (12:22 -0700)]
scsi: ibmvscsis: Ensure partition name is properly NUL terminated
[ Upstream commit
adad633af7b970bfa5dd1b624a4afc83cac9b235 ]
While reviewing another part of the code, Kees noticed that the strncpy of the
partition name might not always be NUL terminated. Switch to using strscpy
which does this safely.
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laura Abbott [Tue, 11 Sep 2018 19:22:25 +0000 (12:22 -0700)]
scsi: ibmvscsis: Fix a stringop-overflow warning
[ Upstream commit
d792d4c4fc866ae224b0b0ca2aabd87d23b4d6cc ]
There's currently a warning about string overflow with strncat:
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c: In function 'ibmvscsis_probe':
drivers/scsi/ibmvscsi_tgt/ibmvscsi_tgt.c:3479:2: error: 'strncat' specified
bound 64 equals destination size [-Werror=stringop-overflow=]
strncat(vscsi->eye, vdev->name, MAX_EYE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Switch to a single snprintf instead of a strcpy + strcat to handle this
cleanly.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Suggested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keerthy [Wed, 8 Aug 2018 13:14:59 +0000 (18:44 +0530)]
clocksource/drivers/ti-32k: Add CLOCK_SOURCE_SUSPEND_NONSTOP flag for non-am43 SoCs
[ Upstream commit
3b7d96a0dbb6b630878597a1838fc39f808b761b ]
The 32k clocksource is NONSTOP for non-am43 SoCs. Hence
add the flag for all the other SoCs.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Lindner [Thu, 6 Sep 2018 21:45:55 +0000 (05:45 +0800)]
batman-adv: fix hardif_neigh refcount on queue_work() failure
[ Upstream commit
4c4af6900844ab04c9434c972021d7b48610e06a ]
The hardif_neigh refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Lindner [Thu, 6 Sep 2018 21:45:54 +0000 (05:45 +0800)]
batman-adv: fix backbone_gw refcount on queue_work() failure
[ Upstream commit
5af96b9c59c72fb2af2d19c5cc2f3cdcee391dff ]
The backbone_gw refcounter is to be decreased by the queued work and
currently is never decreased if the queue_work() call fails.
Fix by checking the queue_work() return value and decrease refcount
if necessary.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Sun, 12 Aug 2018 19:04:45 +0000 (21:04 +0200)]
batman-adv: Prevent duplicated tvlv handler
[ Upstream commit
ae3cdc97dc10c7a3b31f297dab429bfb774c9ccb ]
The function batadv_tvlv_handler_register is responsible for adding new
tvlv_handler to the handler_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes:
ef26157747d4 ("batman-adv: tvlv - basic infrastructure")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Sun, 12 Aug 2018 19:04:44 +0000 (21:04 +0200)]
batman-adv: Prevent duplicated global TT entry
[ Upstream commit
e7136e48ffdfb9f37b0820f619380485eb407361 ]
The function batadv_tt_global_orig_entry_add is responsible for adding new
tt_orig_list_entry to the orig_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes:
d657e621a0f5 ("batman-adv: add reference counting for type batadv_tt_orig_list_entry")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Sun, 12 Aug 2018 19:04:43 +0000 (21:04 +0200)]
batman-adv: Prevent duplicated softif_vlan entry
[ Upstream commit
94cb82f594ed86be303398d6dfc7640a6f1d45d4 ]
The function batadv_softif_vlan_get is responsible for adding new
softif_vlan to the softif_vlan_list. It first checks whether the entry
already is in the list or not. If it is, then the creation of a new entry
is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes:
5d2c05b21337 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Sun, 12 Aug 2018 19:04:42 +0000 (21:04 +0200)]
batman-adv: Prevent duplicated nc_node entry
[ Upstream commit
fa122fec8640eb7186ce5a41b83a4c1744ceef8f ]
The function batadv_nc_get_nc_node is responsible for adding new nc_nodes
to the in_coding_list and out_coding_list. It first checks whether the
entry already is in the list or not. If it is, then the creation of a new
entry is aborted.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes:
d56b1705e28c ("batman-adv: network coding - detect coding nodes and remove these after timeout")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Sun, 12 Aug 2018 19:04:41 +0000 (21:04 +0200)]
batman-adv: Prevent duplicated gateway_node entry
[ Upstream commit
dff9bc42ab0b2d38c5e90ddd79b238fed5b4c7ad ]
The function batadv_gw_node_add is responsible for adding new gw_node to
the gateway_list. It is expecting that the caller already checked that
there is not already an entry with the same key or not.
But the lock for the list is only held when the list is really modified.
This could lead to duplicated entries because another context could create
an entry with the same key between the check and the list manipulation.
The check and the manipulation of the list must therefore be in the same
locked code section.
Fixes:
c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Fri, 31 Aug 2018 14:56:29 +0000 (16:56 +0200)]
batman-adv: Fix segfault when writing to sysfs elp_interval
[ Upstream commit
a25bab9d723a08bd0bdafb1529faf9094c690b70 ]
The per hardif sysfs file "batman_adv/elp_interval" is using the generic
functions to store/show uint values. The helper __batadv_store_uint_attr
requires the softif net_device as parameter to print the resulting change
as info text when the users writes to this file. It uses the helper
function batadv_info to add it at the same time to the kernel ring buffer
and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes:
0744ff8fa8fa ("batman-adv: Add hard_iface specific sysfs wrapper macros for UINT")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Fri, 31 Aug 2018 14:46:47 +0000 (16:46 +0200)]
batman-adv: Fix segfault when writing to throughput_override
[ Upstream commit
b9fd14c20871e6189f635e49b32d7789e430b3c8 ]
The per hardif sysfs file "batman_adv/throughput_override" prints the
resulting change as info text when the users writes to this file. It uses
the helper function batadv_info to add it at the same time to the kernel
ring buffer and to the batman-adv debug log (when CONFIG_BATMAN_ADV_DEBUG
is enabled).
The function batadv_info requires as first parameter the batman-adv softif
net_device. This parameter is then used to find the private buffer which
contains the debug log for this batman-adv interface. But
batadv_store_throughput_override used as first argument the slave
net_device. This slave device doesn't have the batadv_priv private data
which is access by batadv_info.
Writing to this file with CONFIG_BATMAN_ADV_DEBUG enabled can either lead
to a segfault or to memory corruption.
Fixes:
0b5ecc6811bd ("batman-adv: add throughput override attribute to hard_ifaces")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sven Eckelmann [Fri, 31 Aug 2018 13:08:44 +0000 (15:08 +0200)]
batman-adv: Avoid probe ELP information leak
[ Upstream commit
88d0895d0ea9d4431507d576c963f2ff9918144d ]
The probe ELPs for WiFi interfaces are expanded to contain at least
BATADV_ELP_MIN_PROBE_SIZE bytes. This is usually a lot more than the
number of bytes which the template ELP packet requires.
These extra padding bytes were not initialized and thus could contain data
which were previously stored at the same location. It is therefore required
to set it to some predefined or random values to avoid leaking private
information from the system transmitting these kind of packets.
Fixes:
e4623c913508 ("batman-adv: Avoid probe ELP information leak")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jozef Balga [Tue, 21 Aug 2018 09:01:04 +0000 (05:01 -0400)]
media: af9035: prevent buffer overflow on write
[ Upstream commit
312f73b648626a0526a3aceebb0a3192aaba05ce ]
When less than 3 bytes are written to the device, memcpy is called with
negative array size which leads to buffer overflow and kernel panic. This
patch adds a condition and returns -EOPNOTSUPP instead.
Fixes bugzilla issue 64871
[mchehab+samsung@kernel.org: fix a merge conflict and changed the
condition to match the patch's comment, e. g. len == 3 could
also be valid]
Signed-off-by: Jozef Balga <jozef.balga@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 18 Oct 2018 07:16:28 +0000 (09:16 +0200)]
Linux 4.14.77
Jiri Olsa [Mon, 19 Mar 2018 08:29:01 +0000 (09:29 +0100)]
perf tools: Fix snprint warnings for gcc 8
commit
77f18153c080855e1c3fb520ca31a4e61530121d upstream.
With gcc 8 we get new set of snprintf() warnings that breaks the
compilation, one example:
tests/mem.c: In function ‘check’:
tests/mem.c:19:48: error: ‘%s’ directive output may be truncated writing \
up to 99 bytes into a region of size 89 [-Werror=format-truncation=]
snprintf(failure, sizeof failure, "unexpected %s", out);
The gcc docs says:
To avoid the warning either use a bigger buffer or handle the
function's return value which indicates whether or not its output
has been truncated.
Given that all these warnings are harmless, because the code either
properly fails due to uncomplete file path or we don't care for
truncated output at all, I'm changing all those snprintf() calls to
scnprintf(), which actually 'checks' for the snprint return value so the
gcc stays silent.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Link: http://lkml.kernel.org/r/20180319082902.4518-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Ignat Korchagin <ignat@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:18 +0000 (11:32 -0400)]
ARM: spectre-v1: mitigate user accesses
Commit
a3c0f84765bb429ba0fd23de1c57b5e1591c9389 upstream.
Spectre variant 1 attacks are about this sequence of pseudo-code:
index = load(user-manipulated pointer);
access(base + index * stride);
In order for the cache side-channel to work, the access() must me made
to memory which userspace can detect whether cache lines have been
loaded. On 32-bit ARM, this must be either user accessible memory, or
a kernel mapping of that same user accessible memory.
The problem occurs when the load() speculatively loads privileged data,
and the subsequent access() is made to user accessible memory.
Any load() which makes use of a user-maniplated pointer is a potential
problem if the data it has loaded is used in a subsequent access. This
also applies for the access() if the data loaded by that access is used
by a subsequent access.
Harden the get_user() accessors against Spectre attacks by forcing out
of bounds addresses to a NULL pointer. This prevents get_user() being
used as the load() step above. As a side effect, put_user() will also
be affected even though it isn't implicated.
Also harden copy_from_user() by redoing the bounds check within the
arm_copy_from_user() code, and NULLing the pointer if out of bounds.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:17 +0000 (11:32 -0400)]
ARM: spectre-v1: use get_user() for __get_user()
Commit
b1cd0a14806321721aae45f5446ed83a3647c914 upstream.
Fixing __get_user() for spectre variant 1 is not sane: we would have to
add address space bounds checking in order to validate that the location
should be accessed, and then zero the address if found to be invalid.
Since __get_user() is supposed to avoid the bounds check, and this is
exactly what get_user() does, there's no point having two different
implementations that are doing the same thing. So, when the Spectre
workarounds are required, make __get_user() an alias of get_user().
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:16 +0000 (11:32 -0400)]
ARM: use __inttype() in get_user()
Commit
d09fbb327d670737ab40fd8bbb0765ae06b8b739 upstream.
Borrow the x86 implementation of __inttype() to use in get_user() to
select an integer type suitable to temporarily hold the result value.
This is necessary to avoid propagating the volatile nature of the
result argument, which can cause the following warning:
lib/iov_iter.c:413:5: warning: optimization may eliminate reads and/or writes to register variables [-Wvolatile-register-var]
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:15 +0000 (11:32 -0400)]
ARM: oabi-compat: copy semops using __copy_from_user()
Commit
8c8484a1c18e3231648f5ba7cc5ffb7fd70b3ca4 upstream.
__get_user_error() is used as a fast accessor to make copying structure
members as efficient as possible. However, with software PAN and the
recent Spectre variant 1, the efficiency is reduced as these are no
longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
Rather than using __get_user_error() to copy each semops element member,
copy each semops element in full using __copy_from_user().
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:14 +0000 (11:32 -0400)]
ARM: vfp: use __copy_from_user() when restoring VFP state
Commit
42019fc50dfadb219f9e6ddf4c354f3837057d80 upstream.
__get_user_error() is used as a fast accessor to make copying structure
members in the signal handling path as efficient as possible. However,
with software PAN and the recent Spectre variant 1, the efficiency is
reduced as these are no longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
Use __copy_from_user() rather than __get_user_err() for individual
members when restoring VFP state.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:13 +0000 (11:32 -0400)]
ARM: signal: copy registers using __copy_from_user()
Commit
c32cd419d6650e42b9cdebb83c672ec945e6bd7e upstream.
__get_user_error() is used as a fast accessor to make copying structure
members in the signal handling path as efficient as possible. However,
with software PAN and the recent Spectre variant 1, the efficiency is
reduced as these are no longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
It becomes much more efficient to use __copy_from_user() instead, so
let's use this for the ARM integer registers.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:12 +0000 (11:32 -0400)]
ARM: spectre-v1: fix syscall entry
Commit
10573ae547c85b2c61417ff1a106cffbfceada35 upstream.
Prevent speculation at the syscall table decoding by clamping the index
used to zero on invalid system call numbers, and using the csdb
speculative barrier.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:11 +0000 (11:32 -0400)]
ARM: spectre-v1: add array_index_mask_nospec() implementation
Commit
1d4238c56f9816ce0f9c8dbe42d7f2ad81cb6613 upstream.
Add an implementation of the array_index_mask_nospec() function for
mitigating Spectre variant 1 throughout the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:10 +0000 (11:32 -0400)]
ARM: spectre-v1: add speculation barrier (csdb) macros
Commit
a78d156587931a2c3b354534aa772febf6c9e855 upstream.
Add assembly and C macros for the new CSDB instruction.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:09 +0000 (11:32 -0400)]
ARM: KVM: report support for SMCCC_ARCH_WORKAROUND_1
Commit
add5609877c6785cc002c6ed7e008b1d61064439 upstream.
Report support for SMCCC_ARCH_WORKAROUND_1 to KVM guests for affected
CPUs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:08 +0000 (11:32 -0400)]
ARM: KVM: Add SMCCC_ARCH_WORKAROUND_1 fast handling
Commit
b800acfc70d9fb81fbd6df70f2cf5e20f70023d0 upstream.
We want SMCCC_ARCH_WORKAROUND_1 to be fast. As fast as possible.
So let's intercept it as early as we can by testing for the
function call number as soon as we've identified a HVC call
coming from the guest.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:07 +0000 (11:32 -0400)]
ARM: spectre-v2: KVM: invalidate icache on guest exit for Brahma B15
Commit
3c908e16396d130608e831b7fac4b167a2ede6ba upstream.
Include Brahma B15 in the Spectre v2 KVM workarounds.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Zyngier [Mon, 15 Oct 2018 15:32:06 +0000 (11:32 -0400)]
ARM: KVM: invalidate icache on guest exit for Cortex-A15
Commit
0c47ac8cd157727e7a532d665d6fb1b5fd333977 upstream.
In order to avoid aliasing attacks against the branch predictor
on Cortex-A15, let's invalidate the BTB on guest exit, which can
only be done by invalidating the icache (with ACTLR[0] being set).
We use the same hack as for A12/A17 to perform the vector decoding.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marc Zyngier [Mon, 15 Oct 2018 15:32:05 +0000 (11:32 -0400)]
ARM: KVM: invalidate BTB on guest exit for Cortex-A12/A17
Commit
3f7e8e2e1ebda787f156ce46e3f0a9ce2833fa4f upstream.
In order to avoid aliasing attacks against the branch predictor,
let's invalidate the BTB on guest exit. This is made complicated
by the fact that we cannot take a branch before invalidating the
BTB.
We only apply this to A12 and A17, which are the only two ARM
cores on which this useful.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:04 +0000 (11:32 -0400)]
ARM: spectre-v2: warn about incorrect context switching functions
Commit
c44f366ea7c85e1be27d08f2f0880f4120698125 upstream.
Warn at error level if the context switching function is not what we
are expecting. This can happen with big.Little systems, which we
currently do not support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:03 +0000 (11:32 -0400)]
ARM: spectre-v2: add firmware based hardening
Commit
10115105cb3aa17b5da1cb726ae8dd5f6854bd93 upstream.
Add firmware based hardening for cores that require more complex
handling in firmware.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:02 +0000 (11:32 -0400)]
ARM: spectre-v2: harden user aborts in kernel space
Commit
f5fe12b1eaee220ce62ff9afb8b90929c396595f upstream.
In order to prevent aliasing attacks on the branch predictor,
invalidate the BTB or instruction cache on CPUs that are known to be
affected when taking an abort on a address that is outside of a user
task limit:
Cortex A8, A9, A12, A17, A73, A75: flush BTB.
Cortex A15, Brahma B15: invalidate icache.
If the IBE bit is not set, then there is little point to enabling the
workaround.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:01 +0000 (11:32 -0400)]
ARM: spectre-v2: add Cortex A8 and A15 validation of the IBE bit
Commit
e388b80288aade31135aca23d32eee93dd106795 upstream.
When the branch predictor hardening is enabled, firmware must have set
the IBE bit in the auxiliary control register. If this bit has not
been set, the Spectre workarounds will not be functional.
Add validation that this bit is set, and print a warning at alert level
if this is not the case.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:32:00 +0000 (11:32 -0400)]
ARM: spectre-v2: harden branch predictor on context switches
Commit
06c23f5ffe7ad45b908d0fff604dae08a7e334b9 upstream.
Required manual merge of arch/arm/mm/proc-v7.S.
Harden the branch predictor against Spectre v2 attacks on context
switches for ARMv7 and later CPUs. We do this by:
Cortex A9, A12, A17, A73, A75: invalidating the BTB.
Cortex A15, Brahma B15: invalidating the instruction cache.
Cortex A57 and Cortex A72 are not addressed in this patch.
Cortex R7 and Cortex R8 are also not addressed as we do not enforce
memory protection on these cores.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:31:59 +0000 (11:31 -0400)]
ARM: spectre: add Kconfig symbol for CPUs vulnerable to Spectre
Commit
c58d237d0852a57fde9bc2c310972e8f4e3d155d upstream.
Add a Kconfig symbol for CPUs which are vulnerable to the Spectre
attacks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:31:58 +0000 (11:31 -0400)]
ARM: bugs: add support for per-processor bug checking
Commit
9d3a04925deeabb97c8e26d940b501a2873e8af3 upstream.
Add support for per-processor bug checking - each processor function
descriptor gains a function pointer for this check, which must not be
an __init function. If non-NULL, this will be called whenever a CPU
enters the kernel via which ever path (boot CPU, secondary CPU startup,
CPU resuming, etc.)
This allows processor specific bug checks to validate that workaround
bits are properly enabled by firmware via all entry paths to the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:31:57 +0000 (11:31 -0400)]
ARM: bugs: hook processor bug checking into SMP and suspend paths
Commit
26602161b5ba795928a5a719fe1d5d9f2ab5c3ef upstream.
Check for CPU bugs when secondary processors are being brought online,
and also when CPUs are resuming from a low power mode. This gives an
opportunity to check that processor specific bug workarounds are
correctly enabled for all paths that a CPU re-enters the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:31:56 +0000 (11:31 -0400)]
ARM: bugs: prepare processor bug infrastructure
Commit
a5b9177f69329314721aa7022b7e69dab23fa1f0 upstream.
Prepare the processor bug infrastructure so that it can be expanded to
check for per-processor bugs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Mon, 15 Oct 2018 15:31:55 +0000 (11:31 -0400)]
ARM: add more CPU part numbers for Cortex and Brahma B15 CPUs
Commit
f5683e76f35b4ec5891031b6a29036efe0a1ff84 upstream.
Add CPU part numbers for Cortex A53, A57, A72, A73, A75 and the
Broadcom Brahma B15 CPU.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Boot-tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Fri, 11 May 2018 23:01:53 +0000 (16:01 -0700)]
mm: don't show nr_indirectly_reclaimable in /proc/vmstat
commit
7aaf7727235870f497eb928f728f7773d6df3b40 upstream.
Don't show nr_indirectly_reclaimable in /proc/vmstat, because there is
no need to export this vm counter to userspace, and some changes are
expected in reclaimable object accounting, which can alter this counter.
Link: http://lkml.kernel.org/r/20180425191422.9159-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Tue, 10 Apr 2018 23:27:47 +0000 (16:27 -0700)]
mm: treat indirectly reclaimable memory as free in overcommit logic
commit
d79f7aa496fc94d763f67b833a1f36f4c171176f upstream.
Indirectly reclaimable memory can consume a significant part of total
memory and it's actually reclaimable (it will be released under actual
memory pressure).
So, the overcommit logic should treat it as free.
Otherwise, it's possible to cause random system-wide memory allocation
failures by consuming a significant amount of memory by indirectly
reclaimable memory, e.g. dentry external names.
If overcommit policy GUESS is used, it might be used for denial of
service attack under some conditions.
The following program illustrates the approach. It causes the kernel to
allocate an unreclaimable kmalloc-256 chunk for each stat() call, so
that at some point the overcommit logic may start blocking large
allocation system-wide.
int main()
{
char buf[256];
unsigned long i;
struct stat statbuf;
buf[0] = '/';
for (i = 1; i < sizeof(buf); i++)
buf[i] = '_';
for (i = 0; 1; i++) {
sprintf(&buf[248], "%8lu", i);
stat(buf, &statbuf);
}
return 0;
}
This patch in combination with related indirectly reclaimable memory
patches closes this issue.
Link: http://lkml.kernel.org/r/20180313130041.8078-1-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Tue, 10 Apr 2018 23:27:44 +0000 (16:27 -0700)]
dcache: account external names as indirectly reclaimable memory
commit
f1782c9bc547754f4bd3043fe8cfda53db85f13f upstream.
I received a report about suspicious growth of unreclaimable slabs on
some machines. I've found that it happens on machines with low memory
pressure, and these unreclaimable slabs are external names attached to
dentries.
External names are allocated using generic kmalloc() function, so they
are accounted as unreclaimable. But they are held by dentries, which
are reclaimable, and they will be reclaimed under the memory pressure.
In particular, this breaks MemAvailable calculation, as it doesn't take
unreclaimable slabs into account. This leads to a silly situation, when
a machine is almost idle, has no memory pressure and therefore has a big
dentry cache. And the resulting MemAvailable is too low to start a new
workload.
To address the issue, the NR_INDIRECTLY_RECLAIMABLE_BYTES counter is
used to track the amount of memory, consumed by external names. The
counter is increased in the dentry allocation path, if an external name
structure is allocated; and it's decreased in the dentry freeing path.
To reproduce the problem I've used the following Python script:
import os
for iter in range (0,
10000000):
try:
name = ("/some_long_name_%d" % iter) + "_" * 220
os.stat(name)
except Exception:
pass
Without this patch:
$ cat /proc/meminfo | grep MemAvailable
MemAvailable: 7811688 kB
$ python indirect.py
$ cat /proc/meminfo | grep MemAvailable
MemAvailable: 2753052 kB
With the patch:
$ cat /proc/meminfo | grep MemAvailable
MemAvailable: 7809516 kB
$ python indirect.py
$ cat /proc/meminfo | grep MemAvailable
MemAvailable: 7749144 kB
[guro@fb.com: fix indirectly reclaimable memory accounting for CONFIG_SLOB]
Link: http://lkml.kernel.org/r/20180312194140.19517-1-guro@fb.com
[guro@fb.com: fix indirectly reclaimable memory accounting]
Link: http://lkml.kernel.org/r/20180313125701.7955-1-guro@fb.com
Link: http://lkml.kernel.org/r/20180305133743.12746-5-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Tue, 10 Apr 2018 23:27:40 +0000 (16:27 -0700)]
mm: treat indirectly reclaimable memory as available in MemAvailable
commit
034ebf65c3c21d85b963d39f992258a64a85e3a9 upstream.
Adjust /proc/meminfo MemAvailable calculation by adding the amount of
indirectly reclaimable memory (rounded to the PAGE_SIZE).
Link: http://lkml.kernel.org/r/20180305133743.12746-4-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Gushchin [Tue, 10 Apr 2018 23:27:36 +0000 (16:27 -0700)]
mm: introduce NR_INDIRECTLY_RECLAIMABLE_BYTES
commit
eb59254608bc1d42c4c6afdcdce9c0d3ce02b318 upstream.
Patch series "indirectly reclaimable memory", v2.
This patchset introduces the concept of indirectly reclaimable memory
and applies it to fix the issue of when a big number of dentries with
external names can significantly affect the MemAvailable value.
This patch (of 3):
Introduce a concept of indirectly reclaimable memory and adds the
corresponding memory counter and /proc/vmstat item.
Indirectly reclaimable memory is any sort of memory, used by the kernel
(except of reclaimable slabs), which is actually reclaimable, i.e. will
be released under memory pressure.
The counter is in bytes, as it's not always possible to count such
objects in pages. The name contains BYTES by analogy to
NR_KERNEL_STACK_KB.
Link: http://lkml.kernel.org/r/20180305133743.12746-2-guro@fb.com
Signed-off-by: Roman Gushchin <guro@fb.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathias Nyman [Mon, 12 Feb 2018 12:24:47 +0000 (14:24 +0200)]
xhci: Don't print a warning when setting link state for disabled ports
commit
1208d8a84fdcae6b395c57911cdf907450d30e70 upstream.
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd
ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ross Zwisler <zwisler@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Edgar Cherkasov [Thu, 27 Sep 2018 08:56:03 +0000 (11:56 +0300)]
i2c: i2c-scmi: fix for i2c_smbus_write_block_data
commit
08d9db00fe0e300d6df976e6c294f974988226dd upstream.
The i2c-scmi driver crashes when the SMBus Write Block transaction is
executed:
WARNING: CPU: 9 PID: 2194 at mm/page_alloc.c:3931 __alloc_pages_slowpath+0x9db/0xec0
Call Trace:
? get_page_from_freelist+0x49d/0x11f0
? alloc_pages_current+0x6a/0xe0
? new_slab+0x499/0x690
__alloc_pages_nodemask+0x265/0x280
alloc_pages_current+0x6a/0xe0
kmalloc_order+0x18/0x40
kmalloc_order_trace+0x24/0xb0
? acpi_ut_allocate_object_desc_dbg+0x62/0x10c
__kmalloc+0x203/0x220
acpi_os_allocate_zeroed+0x34/0x36
acpi_ut_copy_eobject_to_iobject+0x266/0x31e
acpi_evaluate_object+0x166/0x3b2
acpi_smbus_cmi_access+0x144/0x530 [i2c_scmi]
i2c_smbus_xfer+0xda/0x370
i2cdev_ioctl_smbus+0x1bd/0x270
i2cdev_ioctl+0xaa/0x250
do_vfs_ioctl+0xa4/0x600
SyS_ioctl+0x79/0x90
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
ACPI Error: Evaluating _SBW: 4 (
20170831/smbus_cmi-185)
This problem occurs because the length of ACPI Buffer object is not
defined/initialized in the code before a corresponding ACPI method is
called. The obvious patch below fixes this issue.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Acked-by: Michael Brunner <Michael.Brunner@kontron.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Tue, 9 Oct 2018 10:19:17 +0000 (12:19 +0200)]
mm: Preserve _PAGE_DEVMAP across mprotect() calls
commit
4628a64591e6cee181237060961e98c615c33966 upstream.
Currently _PAGE_DEVMAP bit is not preserved in mprotect(2) calls. As a
result we will see warnings such as:
BUG: Bad page map in process JobWrk0013 pte:
800001803875ea25 pmd:
7624381067
addr:
00007f0930720000 vm_flags:
280000f9 anon_vma: (null) mapping:
ffff97f2384056f0 index:0
file:457-
000000fe00000030-
00000009-
000000ca-00000001_2001.fileblock fault:xfs_filemap_fault [xfs] mmap:xfs_file_mmap [xfs] readpage: (null)
CPU: 3 PID: 15848 Comm: JobWrk0013 Tainted: G W 4.12.14-2.g7573215-default #1 SLE12-SP4 (unreleased)
Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.01.00.0833.
051120182255 05/11/2018
Call Trace:
dump_stack+0x5a/0x75
print_bad_pte+0x217/0x2c0
? enqueue_task_fair+0x76/0x9f0
_vm_normal_page+0xe5/0x100
zap_pte_range+0x148/0x740
unmap_page_range+0x39a/0x4b0
unmap_vmas+0x42/0x90
unmap_region+0x99/0xf0
? vma_gap_callbacks_rotate+0x1a/0x20
do_munmap+0x255/0x3a0
vm_munmap+0x54/0x80
SyS_munmap+0x1d/0x30
do_syscall_64+0x74/0x150
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
...
when mprotect(2) gets used on DAX mappings. Also there is a wide variety
of other failures that can result from the missing _PAGE_DEVMAP flag
when the area gets used by get_user_pages() later.
Fix the problem by including _PAGE_DEVMAP in a set of flags that get
preserved by mprotect(2).
Fixes:
69660fd797c3 ("x86, mm: introduce _PAGE_DEVMAP")
Fixes:
ebd31197931d ("powerpc/mm: Add devmap support for ppc64")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jérôme Glisse [Sat, 13 Oct 2018 04:34:36 +0000 (21:34 -0700)]
mm/thp: fix call to mmu_notifier in set_pmd_migration_entry() v2
commit
bfba8e5cf28f413aa05571af493871d74438979f upstream.
Inside set_pmd_migration_entry() we are holding page table locks and thus
we can not sleep so we can not call invalidate_range_start/end()
So remove call to mmu_notifier_invalidate_range_start/end() because they
are call inside the function calling set_pmd_migration_entry() (see
try_to_unmap_one()).
Link: http://lkml.kernel.org/r/20181012181056.7864-1-jglisse@redhat.com
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Zi Yan <zi.yan@cs.rutgers.edu>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Nellans <dnellans@nvidia.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Will Deacon [Fri, 5 Oct 2018 12:24:36 +0000 (13:24 +0100)]
arm64: perf: Reject stand-alone CHAIN events for PMUv3
commit
ca2b497253ad01c80061a1f3ee9eb91b5d54a849 upstream.
It doesn't make sense for a perf event to be configured as a CHAIN event
in isolation, so extend the arm_pmu structure with a ->filter_match()
function to allow the backend PMU implementation to reject CHAIN events
early.
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marco Felsch [Tue, 2 Oct 2018 08:06:46 +0000 (10:06 +0200)]
pinctrl: mcp23s08: fix irq and irqchip setup order
commit
f259f896f2348f0302f6f88d4382378cf9d23a7e upstream.
Since 'commit
02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")' the
irq request isn't the last devm_* allocation. Without a deeper look at
the irq and testing this isn't a good solution. Since this driver relies
on the devm mechanism, requesting a interrupt should be the last thing
to avoid memory corruptions during unbinding.
'Commit
02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")' fixed the
order for the interrupt-controller use case only. The
mcp23s08_irq_setup() must be split into two to fix it for the
interrupt-controller use case and to register the irq at last. So the
irq will be freed first during unbind.
Cc: stable@vger.kernel.org
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Dmitry Mastykin <mastichi@gmail.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fixes:
82039d244f87 ("pinctrl: mcp23s08: add pinconf support")
Fixes:
02e389e63e35 ("pinctrl: mcp23s08: fix irq setup order")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Boot [Mon, 8 Oct 2018 15:07:30 +0000 (17:07 +0200)]
mmc: block: avoid multiblock reads for the last sector in SPI mode
commit
41591b38f5f8f78344954b68582b5f00e56ffe61 upstream.
On some SD cards over SPI, reading with the multiblock read command the last
sector will leave the card in a bad state.
Remove last sectors from the multiblock reading cmd.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Thu, 4 Oct 2018 20:28:08 +0000 (13:28 -0700)]
cgroup: Fix dom_cgrp propagation when enabling threaded mode
commit
479adb89a97b0a33e5a9d702119872cc82ca21aa upstream.
A cgroup which is already a threaded domain may be converted into a
threaded cgroup if the prerequisite conditions are met. When this
happens, all threaded descendant should also have their ->dom_cgrp
updated to the new threaded domain cgroup. Unfortunately, this
propagation was missing leading to the following failure.
# cd /sys/fs/cgroup/unified
# cat cgroup.subtree_control # show that no controllers are enabled
# mkdir -p mycgrp/a/b/c
# echo threaded > mycgrp/a/b/cgroup.type
At this point, the hierarchy looks as follows:
mycgrp [d]
a [dt]
b [t]
c [inv]
Now let's make node "a" threaded (and thus "mycgrp" s made "domain threaded"):
# echo threaded > mycgrp/a/cgroup.type
By this point, we now have a hierarchy that looks as follows:
mycgrp [dt]
a [t]
b [t]
c [inv]
But, when we try to convert the node "c" from "domain invalid" to
"threaded", we get ENOTSUP on the write():
# echo threaded > mycgrp/a/b/c/cgroup.type
sh: echo: write error: Operation not supported
This patch fixes the problem by
* Moving the opencoded ->dom_cgrp save and restoration in
cgroup_enable_threaded() into cgroup_{save|restore}_control() so
that mulitple cgroups can be handled.
* Updating all threaded descendants' ->dom_cgrp to point to the new
dom_cgrp when enabling threaded mode.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: "Michael Kerrisk (man-pages)" <mtk.manpages@gmail.com>
Reported-by: Amin Jamali <ajamali@pivotal.io>
Reported-by: Joao De Almeida Pereira <jpereira@pivotal.io>
Link: https://lore.kernel.org/r/CAKgNAkhHYCMn74TCNiMJ=ccLd7DcmXSbvw3CbZ1YREeG7iJM5g@mail.gmail.com
Fixes:
454000adaa2a ("cgroup: introduce cgroup->dom_cgrp and threaded css_set handling")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Damien Le Moal [Thu, 11 Oct 2018 02:45:30 +0000 (11:45 +0900)]
dm linear: fix linear_end_io conditional definition
commit
118aa47c7072bce05fc39bd40a1c0a90caed72ab upstream.
The dm-linear target is independent of the dm-zoned target. For code
requiring support for zoned block devices, use CONFIG_BLK_DEV_ZONED
instead of CONFIG_DM_ZONED.
While at it, similarly to dm linear, also enable the DM_TARGET_ZONED_HM
feature in dm-flakey only if CONFIG_BLK_DEV_ZONED is defined.
Fixes:
beb9caac211c1 ("dm linear: eliminate linear_end_io call if CONFIG_DM_ZONED disabled")
Fixes:
0be12c1c7fce7 ("dm linear: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mike Snitzer [Wed, 10 Oct 2018 16:01:55 +0000 (12:01 -0400)]
dm linear: eliminate linear_end_io call if CONFIG_DM_ZONED disabled
commit
beb9caac211c1be1bc118bb62d5cf09c4107e6a5 upstream.
It is best to avoid any extra overhead associated with bio completion.
DM core will indirectly call a DM target's .end_io if it is defined.
In the case of DM linear, there is no need to do so (for every bio that
completes) if CONFIG_DM_ZONED is not enabled.
Avoiding an extra indirect call for every bio completion is very
important for ensuring DM linear doesn't incur more overhead that
further widens the performance gap between dm-linear and raw block
devices.
Fixes:
0be12c1c7fce7 ("dm linear: add support for zoned block devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Damien Le Moal [Tue, 9 Oct 2018 05:24:31 +0000 (14:24 +0900)]
dm: fix report zone remapping to account for partition offset
commit
9864cd5dc54cade89fd4b0954c2e522841aa247c upstream.
If dm-linear or dm-flakey are layered on top of a partition of a zoned
block device, remapping of the start sector and write pointer position
of the zones reported by a report zones BIO must be modified to account
for the target table entry mapping (start offset within the device and
entry mapping with the dm device). If the target's backing device is a
partition of a whole disk, the start sector on the physical device of
the partition must also be accounted for when modifying the zone
information. However, dm_remap_zone_report() was not considering this
last case, resulting in incorrect zone information remapping with
targets using disk partitions.
Fix this by calculating the target backing device start sector using
the position of the completed report zones BIO and the unchanged
position and size of the original report zone BIO. With this value
calculated, the start sector and write pointer position of the target
zones can be correctly remapped.
Fixes:
10999307c14e ("dm: introduce dm_remap_zone_report()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-rpi.git / log