Lennert Buytenhek [Mon, 30 Nov 2009 17:13:42 +0000 (18:13 +0100)]
mwl8k: struct ieee80211_rx_status::qual is deprecated
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:13:34 +0000 (18:13 +0100)]
mwl8k: don't forget to call pci_disable_device()
Don't forget to call pci_disable_device() if pci_request_regions()
fails during probe.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:13:20 +0000 (18:13 +0100)]
mwl8k: increase firmware loading timeouts
The time between loading the helper image and starting to upload the
main firmware image should be at least 5 ms or so. We were doing an
msleep(1) before, and 1 ms appears to not be enough in almost all
cases, but building with HZ=100 has always masked this so far. Bumping
the msleep argument to 5 fixes firmware loading e.g. when HZ=1000.
Some firmware images need more than 200ms to initialize. Bump the
ready code timeout to 500ms to accommodate for this.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:13:04 +0000 (18:13 +0100)]
mwl8k: allow more time for transmit rings to drain
Before issuing any firmware commands, we wait for the transmit rings
to drain, to prevent control versus data path synchronization issues.
In some cases, this can end up taking longer than the current hardcoded
limit of 5 seconds, for example if the transmit rings are filled with
packets for a host that has dropped off the air and we end up
retransmitting every pending packet at the lowest rate a couple of
times.
This patch changes mwl8k_tx_wait_empty() to only bail out on timeout
expiry if there was no change in the number of packets pending in the
transmit rings during the waiting period. If at least one transmit
ring entry was reclaimed while we were waiting, we are apparently still
making progress, and we'll allow waiting for another timeout period.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:12:49 +0000 (18:12 +0100)]
mwl8k: allow more time for firmware commands to complete
Some firmware commands can under some circumstances take more than 2
seconds to complete. This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:12:35 +0000 (18:12 +0100)]
mwl8k: properly report rate on received 40MHz packets
On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index. Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:12:20 +0000 (18:12 +0100)]
mwl8k: fix addr4 zeroing and payload overwrite on DMA header creation
When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.
Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.
This fixes both of these issues.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:12:08 +0000 (18:12 +0100)]
mwl8k: prevent corruption of QoS field on receive
Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field. For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.
We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).
Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.
This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet. It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:11:44 +0000 (18:11 +0100)]
mwl8k: fix UPDATE_STADB command struct legacy_rates array length
There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.
Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.
To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.
In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lennert Buytenhek [Mon, 30 Nov 2009 17:11:18 +0000 (18:11 +0100)]
mwl8k: fix MCS bitmap size in SET_RATE command
The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length. Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vivek Natarajan [Mon, 30 Nov 2009 11:20:53 +0000 (16:50 +0530)]
mac80211: Fix dynamic power save for scanning.
Not only ps_sdata but also IEEE80211_CONF_PS is to be considered
before restoring PS in scan_ps_disable(). For instance, when ps_sdata
is set but CONF_PS is not set just because the dynamic timer is still
running, a sw scan leads to setting of CONF_PS in scan_ps_disable
instead of restarting the dynamic PS timer.
Also for the above case, a null data frame is to be sent after
returning to operating channel which was not happening with the
current implementation. This patch fixes this too.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 29 Nov 2009 11:19:06 +0000 (12:19 +0100)]
mac80211: recalculate idle later in MLME
hwsim testing has revealed that when the MLME
recalculates the idle state of the device, it
sometimes does so before sending the final
deauthentication or disassociation frame. This
patch changes the place where the idle state
is recalculated, but of course driver transmit
is typically asynchronous while configuration
is expected to be synchronous, so it doesn't
fix all possible cases yet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 26 Nov 2009 08:56:13 +0000 (10:56 +0200)]
wl1251: don't build null data template in wl1251_op_config()
The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 26 Nov 2009 08:56:06 +0000 (10:56 +0200)]
wl1251: fix bssid handling
bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise
templates will have incorrect bssid and power save will not work
correctly.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Thu, 26 Nov 2009 08:55:55 +0000 (10:55 +0200)]
wl1251: remove false warning messages
There was a warning from wl1251_op_bss_info_changed():
wl1251: WARNING Set ctsprotect failed 0
It was printed always, it's completely false and can be removed.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 7 Dec 2009 21:37:42 +0000 (16:37 -0500)]
iwlwifi: fix warning from ieee80211_stop_tx_ba_cb_irqsafe argument change
CC [M] drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller [Sat, 5 Dec 2009 23:22:26 +0000 (15:22 -0800)]
Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Conflicts:
drivers/net/pcmcia/fmvj18x_cs.c
drivers/net/pcmcia/nmclan_cs.c
drivers/net/pcmcia/xirc2ps_cs.c
drivers/net/wireless/ray_cs.c
Linus Torvalds [Sat, 5 Dec 2009 17:53:36 +0000 (09:53 -0800)]
Merge branch 'tracing-core-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
tracing: Separate raw syscall from syscall tracer
ring-buffer-benchmark: Add parameters to set produce/consumer priorities
tracing, function tracer: Clean up strstrip() usage
ring-buffer benchmark: Run producer/consumer threads at nice +19
tracing: Remove the stale include/trace/power.h
tracing: Only print objcopy version warning once from recordmcount
tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
ring-buffer: Move access to commit_page up into function used
tracing: do not disable interrupts for trace_clock_local
ring-buffer: Add multiple iterations between benchmark timestamps
kprobes: Sanitize struct kretprobe_instance allocations
tracing: Fix to use __always_unused attribute
compiler: Introduce __always_unused
tracing: Exit with error if a weak function is used in recordmcount.pl
tracing: Move conditional into update_funcs() in recordmcount.pl
tracing: Add regex for weak functions in recordmcount.pl
tracing: Move mcount section search to front of loop in recordmcount.pl
tracing: Fix objcopy revision check in recordmcount.pl
tracing: Check absolute path of input file in recordmcount.pl
tracing: Correct the check for number of arguments in recordmcount.pl
...
Linus Torvalds [Sat, 5 Dec 2009 17:53:21 +0000 (09:53 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Fix trace_marker output
tracing: Fix event format export
tracing: Fix return value of tracing_stats_read()
Linus Torvalds [Sat, 5 Dec 2009 17:53:08 +0000 (09:53 -0800)]
Merge branch 'irq-core-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix spurious irq seqfile conversion
genirq: switch /proc/irq/*/spurious to seq_file
irq: Do not attempt to create subdirectories if /proc/irq/<irq> failed
irq: Remove unused debug_poll_all_shared_irqs()
irq: Fix docbook comments
irq: trivial: Fix typo in comment for #endif
Linus Torvalds [Sat, 5 Dec 2009 17:52:46 +0000 (09:52 -0800)]
Merge branch 'core-softlockup-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: Fix hung_task_check_count sysctl
Linus Torvalds [Sat, 5 Dec 2009 17:52:33 +0000 (09:52 -0800)]
Merge branch 'core-signal-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
signal: Print warning message when dropping signals
signal: Fix alternate signal stack check
Linus Torvalds [Sat, 5 Dec 2009 17:52:14 +0000 (09:52 -0800)]
Merge branch 'core-rcu-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
rcu: Make RCU's CPU-stall detector be default
rcu: Add expedited grace-period support for preemptible RCU
rcu: Enable fourth level of TREE_RCU hierarchy
rcu: Rename "quiet" functions
rcu: Re-arrange code to reduce #ifdef pain
rcu: Eliminate unneeded function wrapping
rcu: Fix grace-period-stall bug on large systems with CPU hotplug
rcu: Eliminate __rcu_pending() false positives
rcu: Further cleanups of use of lastcomp
rcu: Simplify association of forced quiescent states with grace periods
rcu: Accelerate callback processing on CPUs not detecting GP end
rcu: Mark init-time-only rcu_bootup_announce() as __init
rcu: Simplify association of quiescent states with grace periods
rcu: Rename dynticks_completed to completed_fqs
rcu: Enable synchronize_sched_expedited() fastpath
rcu: Remove inline from forward-referenced functions
rcu: Fix note_new_gpnum() uses of ->gpnum
rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter
rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter
rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls
...
Linus Torvalds [Sat, 5 Dec 2009 17:50:22 +0000 (09:50 -0800)]
Merge branch 'core-printk-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ratelimit: Make suppressed output messages more useful
printk: Remove ratelimit.h from kernel.h
ratelimit: Fix/allow use in atomic contexts
ratelimit: Use per ratelimit context locking
Linus Torvalds [Sat, 5 Dec 2009 17:49:59 +0000 (09:49 -0800)]
Merge branch 'core-locking-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mutex: Fix missing conditions to build mutex_spin_on_owner()
mutex: Better control mutex adaptive spinning config
locking, task_struct: Reduce size on TRACE_IRQFLAGS and 64bit
locking: Use __[SPIN|RW]_LOCK_UNLOCKED in [spin|rw]_lock_init()
locking: Remove unused prototype
locking: Reduce ifdefs in kernel/spinlock.c
locking: Make inlining decision Kconfig based
Linus Torvalds [Sat, 5 Dec 2009 17:49:46 +0000 (09:49 -0800)]
Merge branch 'core-ipi-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
generic-ipi: Add smp_call_function_any()
generic-ipi: Fix misleading smp_call_function*() description
Linus Torvalds [Sat, 5 Dec 2009 17:49:07 +0000 (09:49 -0800)]
Merge branch 'core-iommu-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
Linus Torvalds [Sat, 5 Dec 2009 17:47:17 +0000 (09:47 -0800)]
Merge git://git./linux/kernel/git/steve/gfs2-2.6-nmw
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (31 commits)
GFS2: Fix glock refcount issues
writeback: remove unused nonblocking and congestion checks (gfs2)
GFS2: drop rindex glock to refresh rindex list
GFS2: Tag all metadata with jid
GFS2: Locking order fix in gfs2_check_blk_state
GFS2: Remove dirent_first() function
GFS2: Display nobarrier option in /proc/mounts
GFS2: add barrier/nobarrier mount options
GFS2: remove division from new statfs code
GFS2: Improve statfs and quota usability
GFS2: Use dquot_send_warning()
VFS: Export dquot_send_warning
GFS2: Add set_xquota support
GFS2: Add get_xquota support
GFS2: Clean up gfs2_adjust_quota() and do_glock()
GFS2: Remove constant argument from qd_get()
GFS2: Remove constant argument from qdsb_get()
GFS2: Add proper error reporting to quota sync via sysfs
GFS2: Add get_xstate quota function
GFS2: Remove obsolete code in quota.c
...
Linus Torvalds [Sat, 5 Dec 2009 17:44:57 +0000 (09:44 -0800)]
Merge branch 'next' of git://git./linux/kernel/git/jmorris/security-testing-2.6
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
TOMOYO: Add recursive directory matching operator support.
remove CONFIG_SECURITY_FILE_CAPABILITIES compile option
SELinux: print denials for buggy kernel with unknown perms
Silence the existing API for capability version compatibility check.
LSM: Move security_path_chmod()/security_path_chown() to after mutex_lock().
SELinux: header generation may hit infinite loop
selinux: Fix warnings
security: report the module name to security_module_request
Config option to set a default LSM
sysctl: require CAP_SYS_RAWIO to set mmap_min_addr
tpm: autoload tpm_tis based on system PnP IDs
tpm_tis: TPM_STS_DATA_EXPECT workaround
define convenient securebits masks for prctl users (v2)
tpm: fix header for modular build
tomoyo: improve hash bucket dispersion
tpm add default function definitions
LSM: imbed ima calls in the security hooks
SELinux: add .gitignore files for dynamic classes
security: remove root_plug
SELinux: fix locking issue introduced with
c6d3aaa4e35c71a3
...
Linus Torvalds [Sat, 5 Dec 2009 17:42:59 +0000 (09:42 -0800)]
Merge git://git./linux/kernel/git/brodo/pcmcia-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
pcmcia: rework the irq_req_t typedef
pcmcia: remove deprecated handle_to_dev() macro
pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
pcmcia: remove unused "window_t" typedef
pcmcia: move some window-related code to pcmcia_ioctl.c
pcmcia: Change window_handle_t logic to unsigned long
pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
drivers/pcmcia: remove unnecessary kzalloc
pcmcia: correct handling for Zoomed Video registers in topic.h
pcmcia: fix printk formats
pcmcia: autoload module pcmcia
pcmcia/staging: update comedi drivers
PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
PCMCIA: ss: allow PCI IRQs > 255
PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
PCMCIA: soc_common: constify soc_pcmcia_socket ops member
PCMCIA: sa1111: remove duplicated initializers
PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
...
David Daney [Sat, 5 Dec 2009 01:44:54 +0000 (17:44 -0800)]
avr32: Convert BUG() to use unreachable()
Use the new unreachable() macro instead of for(;;);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Daney [Sat, 5 Dec 2009 01:44:53 +0000 (17:44 -0800)]
s390: Convert BUG() to use unreachable()
Use the new unreachable() macro instead of for(;;);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux390@de.ibm.com
CC: linux-s390@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Daney [Sat, 5 Dec 2009 01:44:52 +0000 (17:44 -0800)]
MIPS: Convert BUG() to use unreachable()
Use the new unreachable() macro instead of while(1);
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Daney [Sat, 5 Dec 2009 01:44:51 +0000 (17:44 -0800)]
x86: Convert BUG() to use unreachable()
Use the new unreachable() macro instead of for(;;);. When
allyesconfig is built with a GCC-4.5 snapshot on i686 the size of the
text segment is reduced by 3987 bytes (from 6827019 to 6823032).
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: x86@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Daney [Sat, 5 Dec 2009 01:44:50 +0000 (17:44 -0800)]
Add support for GCC-4.5's __builtin_unreachable() to compiler.h (v2)
Starting with version 4.5, GCC has a new built-in function
__builtin_unreachable() that can be used in places like the kernel's
BUG() where inline assembly is used to transfer control flow. This
eliminated the need for an endless loop in these places.
The patch adds a new macro 'unreachable()' that will expand to either
__builtin_unreachable() or an endless loop depending on the compiler
version.
Change from v1: Simplify unreachable() for non-GCC 4.5 case.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Berg [Fri, 4 Dec 2009 22:25:43 +0000 (14:25 -0800)]
mac80211: fix reorder buffer release
My patch "mac80211: correctly place aMPDU RX reorder code"
uses an skb queue for MPDUs that were released from the
buffer. I intentially didn't initialise and use the skb
queue's spinlock, but in this place forgot that the code
variant that doesn't touch the spinlock is needed.
Thanks to Christian Lamparter for quickly spotting the
bug in the backtrace Reinette reported.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Bug-identified-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 4 Dec 2009 21:25:15 +0000 (13:25 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6
Samuel Ortiz [Thu, 3 Dec 2009 10:40:18 +0000 (11:40 +0100)]
iwmc3200wifi: Enable wimax core through module parameter
When debugging the wifi firmware, we need to disable the wimax core to gain
some memory space. The default value will keep the wimax core enabled.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Thu, 3 Dec 2009 10:40:17 +0000 (11:40 +0100)]
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
Wifi and wimax coexistence mode is set by wifi at boot time. There can be
several modes, defined by priority tables. User space components can decide
which one to select by writing to /sys/module/iwmc3200wifi/parameters/wiwi
with this patch, before bringing the interface up.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Thu, 3 Dec 2009 10:40:16 +0000 (11:40 +0100)]
iwmc3200wifi: Coex table command does not expect a response
When sending the wiwi coexistence priority table, we should not tell the LMAC
that we want a response.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Samuel Ortiz [Thu, 3 Dec 2009 10:40:15 +0000 (11:40 +0100)]
iwmc3200wifi: Update wiwi priority table
This update follows the firmware engineers recommendations.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reinette Chatre [Wed, 2 Dec 2009 20:53:01 +0000 (12:53 -0800)]
iwlwifi: driver version track kernel version
The driver version number is a remnant from when there was an out-of-tree
iwlwifi driver. Now that the driver forms part of kernel source we do not
need a separate driver version. Instead, we now use the kernel version as
driver version. We maintain the previous tags used to indicate which
components the driver has been compiled with.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 2 Dec 2009 20:53:00 +0000 (12:53 -0800)]
iwlwifi: indicate uCode type when fail dump error/event log
error_event_table_ptr is only set upon receipt of REPLY_ALIVE. Until
then both event log and error log will fail. Add information to indicate
which uCode encounter the failure case.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Wed, 2 Dec 2009 20:52:59 +0000 (12:52 -0800)]
iwl3945: remove duplicated event logging code
In the process of improving uCode event logging capability, the new
implementation was introduced without removing the existing
implementation. The event log will be dumped to dmesg twice.
Remove the old implementation to only log the event once upon sys
assert or request by user.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 2 Dec 2009 10:20:36 +0000 (11:20 +0100)]
b43: fix two warnings
My gcc appears to be able to see past the function
boundary and notices that the variable 'behaviour'
could be used uninitialised:
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_register’:
drivers/net/wireless/b43/leds.c:339: warning: ‘behaviour’ may be used uninitialized in this function
drivers/net/wireless/b43/leds.c: In function ‘b43_leds_init’:
drivers/net/wireless/b43/leds.c:262: warning: ‘behaviour’ may be used uninitialized in this function
because b43_led_get_sprominfo() didn't initialise
it in all cases.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Wed, 2 Dec 2009 06:24:37 +0000 (14:24 +0800)]
ipw2100: fix rebooting hang with driver loaded
Add PCI .shutdown method so that we can disable the device during
shutdown or reboot. Without this, the reboot doesn't work well on
some platforms.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2124
Tested-by: pablo <pablolm2005@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo [Tue, 1 Dec 2009 08:47:15 +0000 (10:47 +0200)]
cfg80211: indent regulatory messages with spaces
The regulatory messages in syslog look weird:
kernel: cfg80211: Regulatory domain: US
kernel: ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
kernel: ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
kernel: ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
kernel: ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
Indent them with four spaces instead of the tab character to get prettier
output.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Tue, 1 Dec 2009 03:48:50 +0000 (11:48 +0800)]
iwmc3200wifi: fix NULL pointer dereference in pmkid update
When handling IWM_CMD_PMKID_FLUSH command, the bssid and
pmkid in pmksa are all NULL. Check it before memcpy.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni Malinen [Sun, 29 Nov 2009 12:29:42 +0000 (14:29 +0200)]
mac80211: Fix TX status reporting for injected data frames
An earlier optimization on removing unnecessary traffic on cooked
monitor interfaces ("mac80211: reduce the amount of unnecessary traffic
on cooked monitor interfaces ") ended up removing quite a bit more
than just unnecessary traffic. It was not supposed to remove TX status
reporting for injected frames, but ended up doing it by checking the
injected flag in skb->cb only after that field had been cleared with
memset.. Fix this by taking a local copy of the injected flag before
skb->cb is cleared.
This broke user space applications that depend on getting TX status
notifications for injected data frames. For example, STA inactivity
poll from hostapd did not work and ended up kicking out stations even
if they were still present.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gabor Juhos [Fri, 27 Nov 2009 11:01:35 +0000 (12:01 +0100)]
ath9k: enable 2GHz band only if the device supports it
Currently, the 2GHz band is enabled unconditionally, even if the device
does not support it.
Changes-licensed-under: ISC
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 25 Nov 2009 21:55:11 +0000 (22:55 +0100)]
airo: Fix integer overflow warning
On BigEndian gcc complains:
drivers/net/wireless/airo.c: In function ‘sniffing_mode’:
drivers/net/wireless/airo.c:4809: warning: integer overflow in expression
Fix this by doing the bitwise AND on the host-endian value.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 24 Nov 2009 22:11:32 +0000 (23:11 +0100)]
rt2x00: Fix padding bug on L2PAD devices.
While reviewing the l2pad function to align both the header and the payload
on a DMA-capable boundary a bug was discovered where the payload would not
be properly aligned. The header_align value was used where the payload_align
value should have been used.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jean Tourrilhes [Tue, 24 Nov 2009 18:47:08 +0000 (10:47 -0800)]
WE: Fix set events not propagated
I've just noticed that some events are no longer propagated
for some wireless drivers. Basically, SET request with a extra payload
for driver without commit handler. The fix is pretty simple, see
attached.
Actually, a few lines below this line, you will see that the
event generation for simple SET (iwpoint-less ?) is done properly,
and this other event generation does not need fixing.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 24 Nov 2009 00:42:36 +0000 (18:42 -0600)]
b43legacy: avoid PPC fault during resume
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43legacy_status()
returns a value of 2 (B43legacy_STAT_STARTED); however, one finds that
the driver is unable to associate after resuming from hibernation unless
this routine returns 1. To satisfy both conditions, the routine is rewritten
to return TRUE whenever b43legacy_status() returns a value < 2.
This patch fixes the second problem listed in the postings for Red Hat
Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 24 Nov 2009 00:40:45 +0000 (18:40 -0600)]
b43: avoid PPC fault during resume
The routine b43_is_hw_radio_enabled() has long been a problem.
For PPC architecture with PHY Revision < 3, a read of the register
B43_MMIO_HWENABLED_LO will cause a CPU fault unless b43_status()
returns a value of 2 (B43_STAT_STARTED) (BUG 14181). Fixing that
results in Bug 14538 in which the driver is unable to reassociate
after resuming from hibernation because b43_status() returns 0.
The correct fix would be to determine why the status is 0; however,
I have not yet found why that happens. The correct value is found for
my device, which has PHY revision >= 3.
Returning TRUE when the PHY revision < 3 and b43_status() returns 0 fixes
the regression for 2.6.32.
This patch fixes the problem in Red Hat Bugzilla #538523.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eric Dumazet [Thu, 3 Dec 2009 00:49:01 +0000 (00:49 +0000)]
tcp: fix a timewait refcnt race
After TCP RCU conversion, tw->tw_refcnt should not be set to 1 in
inet_twsk_alloc(). It allows a RCU reader to get this timewait socket,
while we not yet stabilized it.
Only choice we have is to set tw_refcnt to 0 in inet_twsk_alloc(),
then atomic_add() it later, once everything is done.
Location of this atomic_add() is tricky, because we dont want another
writer to find this timewait in ehash, while tw_refcnt is still zero !
Thanks to Kapil Dakhane tests and reports.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 2 Dec 2009 22:31:19 +0000 (22:31 +0000)]
tcp: connect() race with timewait reuse
Its currently possible that several threads issuing a connect() find
the same timewait socket and try to reuse it, leading to list
corruptions.
Condition for bug is that these threads bound their socket on same
address/port of to-be-find timewait socket, and connected to same
target. (SO_REUSEADDR needed)
To fix this problem, we could unhash timewait socket while holding
ehash lock, to make sure lookups/changes will be serialized. Only
first thread finds the timewait socket, other ones find the
established socket and return an EADDRNOTAVAIL error.
This second version takes into account Evgeniy's review and makes sure
inet_twsk_put() is called outside of locked sections.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suresh R [Fri, 4 Dec 2009 00:15:52 +0000 (16:15 -0800)]
be2net: Add support for ethtool self test
This patch adds support for ethtool selftest.
From: Suresh R <sureshr@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 4 Dec 2009 00:06:13 +0000 (16:06 -0800)]
tcp: diag: Dont report negative values for rx queue
Both netlink and /proc/net/tcp interfaces can report transient
negative values for rx queue.
ss ->
State Recv-Q Send-Q Local Address:Port Peer Address:Port
ESTAB -6 6 127.0.0.1:45956 127.0.0.1:3333
netstat ->
tcp
4294967290 6 127.0.0.1:37784 127.0.0.1:3333 ESTABLISHED
This is because we dont lock socket while computing
tp->rcv_nxt - tp->copied_seq,
and another CPU can update copied_seq before rcv_next in RX path.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tristram Ha [Thu, 3 Dec 2009 11:06:42 +0000 (11:06 +0000)]
net: Fix ks8851 snl NULL pointer dereference Oops
This fixes the NULL pointer dereference Oops in the ks8851 snl network
driver during transmission. All socket buffers from the queue are
processed inside the loop, but new workqueues have been scheduled to
run.
Signed-off-by: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick Mullaney [Thu, 3 Dec 2009 23:59:22 +0000 (15:59 -0800)]
netdevice: provide common routine for macvlan and vlan operstate management
Provide common routine for the transition of operational state for a leaf
device during a root device transition.
Signed-off-by: Patrick Mullaney <pmullaney@novell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 3 Dec 2009 23:58:00 +0000 (15:58 -0800)]
bnx2: Refine VPD logic.
- Replace magic values with constants
- Simplify length calculation and fix a bug
Based on valuable feedback from Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Thu, 3 Dec 2009 11:33:54 +0000 (11:33 +0000)]
ixgbe: use EIAM to automask MSI-X
when disabling interrupts, driver was writing with IO, this is no
necessary because on ixgbe parts the hardware can "oneshot"
disable and clear the interrupt. So on 82598/82599 use of EIAM
should avoid one posted write per interrupt when in MSI-X mode.
This should improve performance and seems to in my limited
testing, reduce CPU utilization VERY slightly.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Thu, 3 Dec 2009 11:33:29 +0000 (11:33 +0000)]
ixgbe: performance tweaks
drop variables that had cache lines modified in simultaneous hot paths.
keep some variables modified on hot paths but make their storage per queue.
cache align DMA data buffer start addresses.
cache align (padding) some structures that end within a cacheline.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Thu, 3 Dec 2009 11:33:07 +0000 (11:33 +0000)]
ixgbe: change default ring size
decrease the memory utilization of the tx / rx queue allocation
by changing the default ring size to 512 (from 1024). At
1024 rx entries of 2KB each (from 4kB slab) with 16 queues
ixgbe was using 64 MB of memory per port, which is not
necessary.
Users can still change queue lengths with ethtool -k.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Thu, 3 Dec 2009 11:32:44 +0000 (11:32 +0000)]
ixgbe: select FCoE Tx queue in ndo_select_queue
This removes the Tx queue selection for FCoE traffic from ixgbe_xmit_frame()
and does it in the ndo_select_queue() call, moving all Tx queue selection
into a single routine.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yi Zou [Thu, 3 Dec 2009 11:32:22 +0000 (11:32 +0000)]
ixgbe: use known user priority for FCoE when DCB is enabled
Store the user priority for FCoE and use it directly for outgoing
FCoE traffic when DCB is enabled.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Thu, 3 Dec 2009 23:31:18 +0000 (15:31 -0800)]
usbnet & cdc-ether: Autosuspend for online devices
Using remote wakeup and delayed transmission to allow
online device to go into usb autosuspend.
Minimal alternate support for devices that don't support
remote wakeup.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oliver Neukum [Thu, 3 Dec 2009 11:41:07 +0000 (11:41 +0000)]
cdc-ether: Implement reset_resume()
Normal resume can do double duty as reset_resume() for this driver
as it keeps no state in the device
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 3 Dec 2009 21:51:02 +0000 (13:51 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-next-2.6
David S. Miller [Thu, 3 Dec 2009 21:23:12 +0000 (13:23 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-next-2.6
Michael Chan [Thu, 3 Dec 2009 09:46:35 +0000 (09:46 +0000)]
bnx2: Update version to 2.0.3.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 3 Dec 2009 09:46:34 +0000 (09:46 +0000)]
bnx2: Read firmware version from VPD.
And display it through ethtool -i.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 3 Dec 2009 09:46:33 +0000 (09:46 +0000)]
bnx2: Print warning when unable to allocate the full SKB/page ring.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 3 Dec 2009 09:46:32 +0000 (09:46 +0000)]
bnx2: Dump some state during tx timeout.
To help debug the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Thu, 3 Dec 2009 09:46:31 +0000 (09:46 +0000)]
bnx2: Protect tx timeout reset with rtnl_lock().
To prevent race conditions with other reset events.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:25 +0000 (08:36 +0000)]
tg3: Update version to 3.105
This patch updates the tg3 version to 3.105.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:24 +0000 (08:36 +0000)]
tg3: Clean tg3_init_one()
Tg3's firmware is no longer loaded from tg3_init_one(). Remove the
error path that releases the firmware back to the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:23 +0000 (08:36 +0000)]
tg3: Use pci_read_vpd() instead of private method
If the driver needs to use PCI configuration space to read the VPD data,
the accesses could collide with the pci_read_vpd() function. This patch
converts the driver to use pci_read_vpd() to avoid any potential
collisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:22 +0000 (08:36 +0000)]
tg3: Add some VPD preprocessor constants
This patch cleans up the VPD code by creating preprocessor definitions
and using them in the place of hardcoded constants.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:21 +0000 (08:36 +0000)]
tg3: Add 57765 asic rev
This patch adds the 57765 asic revision.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Thu, 3 Dec 2009 08:36:20 +0000 (08:36 +0000)]
tg3: Make TSS enable independent of MSI-X enable
The 57765 asic rev has MSI-X capability, but does not support TSS. This
patch changes the tx paths so that TSS is explicitly mentioned, rather
than implied through the ENABLE_MSIX flag.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches [Thu, 3 Dec 2009 07:58:21 +0000 (07:58 +0000)]
drivers/net: Move && and || to end of previous line
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Thu, 3 Dec 2009 06:19:08 +0000 (06:19 +0000)]
be2net: Bump up the driver version number
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Thu, 3 Dec 2009 06:16:59 +0000 (06:16 +0000)]
be2net: Support for WoL using magic packet after suspend.
Add support for WOL using Magic Packet after suspend is done.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Thu, 3 Dec 2009 06:12:06 +0000 (06:12 +0000)]
be2net: Changes to print fw command opcode when command is failed by controller.
When a firmware command fails, only the failure codes are printed.
It is difficult to co-relate this to the actual command that has failed.
These changes will now print the command code that has failed.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 02:29:09 +0000 (02:29 +0000)]
net: Batch inet_twsk_purge
This function walks the whole hashtable so there is no point in
passing it a network namespace. Instead I purge all timewait
sockets from dead network namespaces that I find. If the namespace
is one of the once I am trying to purge I am guaranteed no new timewait
sockets can be formed so this will get them all. If the namespace
is one I am not acting for it might form a few more but I will
call inet_twsk_purge again and shortly to get rid of them. In
any even if the network namespace is dead timewait sockets are
useless.
Move the calls of inet_twsk_purge into batch_exit routines so
that if I am killing a bunch of namespaces at once I will just
call inet_twsk_purge once and save a lot of redundant unnecessary
work.
My simple 4k network namespace exit test the cleanup time dropped from
roughly 8.2s to 1.6s. While the time spent running inet_twsk_purge fell
to about 2ms. 1ms for ipv4 and 1ms for ipv6.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 02:29:08 +0000 (02:29 +0000)]
net: Use rcu lookups in inet_twsk_purge.
While we are looking up entries to free there is no reason to take
the lock in inet_twsk_purge. We have to drop locks and restart
occassionally anyway so adding a few more in case we get on the
wrong list because of a timewait move is no big deal. At the
same time not taking the lock for long periods of time is much
more polite to the rest of the users of the hash table.
In my test configuration of killing 4k network namespaces
this change causes 4k back to back runs of inet_twsk_purge on an
empty hash table to go from roughly 20.7s to 3.3s, and the total
time to destroy 4k network namespaces goes from roughly 44s to
3.3s.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 20:22:55 +0000 (12:22 -0800)]
net: Allow fib_rule_unregister to batch
Refactor the code so fib_rules_register always takes a template instead
of the actual fib_rules_ops structure that will be used. This is
required for network namespace support so 2 out of the 3 callers already
do this, it allows the error handling to be made common, and it allows
fib_rules_unregister to free the template for hte caller.
Modify fib_rules_unregister to use call_rcu instead of syncrhonize_rcu
to allw multiple namespaces to be cleaned up in the same rcu grace
period.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 02:29:06 +0000 (02:29 +0000)]
netns: Add an explicit rcu_barrier to unregister_pernet_{device|subsys}
This allows namespace exit methods to batch work that comes requires an
rcu barrier using call_rcu without having to treat the
unregister_pernet_operations cases specially.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 02:29:05 +0000 (02:29 +0000)]
net: Allow xfrm_user_net_exit to batch efficiently.
xfrm.nlsk is provided by the xfrm_user module and is access via rcu from
other parts of the xfrm code. Add xfrm.nlsk_stash a copy of xfrm.nlsk that
will never be set to NULL. This allows the synchronize_net and
netlink_kernel_release to be deferred until a whole batch of xfrm.nlsk sockets
have been set to NULL.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 02:29:04 +0000 (02:29 +0000)]
net: Move network device exit batching
Move network device exit batching from a special case in
net_namespace.c to using common mechanisms in dev.c
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Thu, 3 Dec 2009 02:29:03 +0000 (02:29 +0000)]
net: Add support for batching network namespace cleanups
- Add exit_list to struct net to support building lists of network
namespaces to cleanup.
- Add exit_batch to pernet_operations to allow running operations only
once during a network namespace exit. Instead of once per network
namespace.
- Factor opt ops_exit_list and ops_exit_free so the logic with cleanup
up a network namespace does not need to be duplicated.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 3 Dec 2009 01:25:58 +0000 (01:25 +0000)]
ipv4 05/05: add sysctl to accept packets with local source addresses
commit
8ec1e0ebe26087bfc5c0394ada5feb5758014fc8
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:16:35 2009 +0100
ipv4: add sysctl to accept packets with local source addresses
Change fib_validate_source() to accept packets with a local source address when
the "accept_local" sysctl is set for the incoming inet device. Combined with the
previous patches, this allows to communicate between multiple local interfaces
over the wire.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 3 Dec 2009 01:25:57 +0000 (01:25 +0000)]
net 04/05: fib_rules: allow to delete local rule
commit
d124356ce314fff22a047ea334379d5105b2d834
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:16:35 2009 +0100
net: fib_rules: allow to delete local rule
Allow to delete the local rule and recreate it with a higher priority. This
can be used to force packets with a local destination out on the wire instead
of routing them to loopback. Additionally this patch allows to recreate rules
with a priority of 0.
Combined with the previous patch to allow oif classification, a socket can
be bound to the desired interface and packets routed to the wire like this:
# move local rule to lower priority
ip rule add pref 1000 lookup local
ip rule del pref 0
# route packets of sockets bound to eth0 to the wire independant
# of the destination address
ip rule add pref 100 oif eth0 lookup 100
ip route add default dev eth0 table 100
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 3 Dec 2009 01:25:56 +0000 (01:25 +0000)]
net 03/05: fib_rules: add oif classification
commit
68144d350f4f6c348659c825cde6a82b34c27a91
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:05:25 2009 +0100
net: fib_rules: add oif classification
Support routing table lookup based on the flow's oif. This is useful to
classify packets originating from sockets bound to interfaces differently.
The route cache already includes the oif and needs no changes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 3 Dec 2009 01:25:54 +0000 (01:25 +0000)]
net 02/05: fib_rules: rename ifindex/ifname/FRA_IFNAME to iifindex/iifname/FRA_IIFNAME
commit
229e77eec406ad68662f18e49fda8b5d366768c5
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:05:23 2009 +0100
net: fib_rules: rename ifindex/ifname/FRA_IFNAME to iifindex/iifname/FRA_IIFNAME
The next patch will add oif classification, rename interface related members
and attributes to reflect that they're used for iif classification.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 3 Dec 2009 01:25:53 +0000 (01:25 +0000)]
net 01/05: fib_rules: rearrange struct fib_rule
commit
b8952893d5d86f69c4e499d191b98c6658f64b0f
Author: Patrick McHardy <kaber@trash.net>
Date: Thu Dec 3 12:05:22 2009 +0100
net: fib_rules: rearrange struct fib_rule
The ifname member is only used to resolve interface names and is not needed
during rule lookups. The target and ctarget members however are used during
rule lookups and are currently located in a second cacheline.
Move ifname further to the end to make sure both target and ctarget are
located in the same cacheline as other members used during rule lookups.
The layout on 64 bit changes from:
struct fib_rule {
...
u32 table; /* 56 4 */
u8 action; /* 60 1 */
/* XXX 3 bytes hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
u32 target; /* 64 4 */
/* XXX 4 bytes hole, try to pack */
struct fib_rule * ctarget; /* 72 8 */
struct rcu_head rcu; /* 80 16 */
struct net * fr_net; /* 96 8 */
};
to:
struct fib_rule {
...
u32 table; /* 40 4 */
u8 action; /* 44 1 */
/* XXX 3 bytes hole, try to pack */
u32 target; /* 48 4 */
/* XXX 4 bytes hole, try to pack */
struct fib_rule * ctarget; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
char ifname[16]; /* 64 16 */
struct rcu_head rcu; /* 80 16 */
struct net * fr_net; /* 96 8 */
};
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Sat, 7 Nov 2009 21:41:18 +0000 (21:41 +0000)]
Bluetooth: Declare MODULE_FIRMWARE for Marvell SDIO driver
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Mon, 5 Oct 2009 10:23:48 +0000 (12:23 +0200)]
Bluetooth: Add RFCOMM option to use L2CAP ERTM mode
By default the RFCOMM layer would still use L2CAP basic mode. For testing
purposes this option enables RFCOMM to select enhanced retransmission
mode.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
projects / profile / common / kernel-common.git / log