platform/kernel/linux-rpi.git
2 years agoath9k: Remove unnecessary print function dev_err()
Yang Li [Fri, 8 Apr 2022 00:01:13 +0000 (08:01 +0800)]
ath9k: Remove unnecessary print function dev_err()

The print function dev_err() is redundant because
platform_get_irq_byname() already prints an error.

Eliminate the follow coccicheck warning:
./drivers/net/wireless/ath/ath9k/ahb.c:103:2-9: line 103 is redundant
because platform_get_irq() already prints an error

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220408000113.129906-2-yang.lee@linux.alibaba.com
2 years agowcn36xx: clean up some inconsistent indenting
Yang Li [Fri, 8 Apr 2022 00:01:12 +0000 (08:01 +0800)]
wcn36xx: clean up some inconsistent indenting

Eliminate the follow smatch warning:
drivers/net/wireless/ath/wcn36xx/smd.c:3151
wcn36xx_smd_gtk_offload_get_info_rsp() warn: inconsistent indenting

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220408000113.129906-1-yang.lee@linux.alibaba.com
2 years agoath11k: Fix spelling mistake "reseting" -> "resetting"
Colin Ian King [Thu, 7 Apr 2022 10:28:20 +0000 (11:28 +0100)]
ath11k: Fix spelling mistake "reseting" -> "resetting"

There is a spelling mistake in an ath11k_warn message. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220407102820.613881-1-colin.i.king@gmail.com
2 years agoath9k: fix ath_get_rate_txpower() to respect the rate list end tag
Peter Seiderer [Sat, 2 Apr 2022 15:30:13 +0000 (17:30 +0200)]
ath9k: fix ath_get_rate_txpower() to respect the rate list end tag

Stop reading (and copying) from ieee80211_tx_rate to ath_tx_info.rates
after list end tag (count == 0, idx < 0), prevents copying of garbage
to card registers.

Note: no need to write to the remaining ath_tx_info.rates entries
as the complete ath_tx_info struct is already initialized to zero from
both call sites.

Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220402153014.31332-1-ps.report@gmx.net
2 years agoMerge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
Kalle Valo [Wed, 6 Apr 2022 08:37:55 +0000 (11:37 +0300)]
Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git

ath.git patches for v5.19. Major changes:

ath11k

* Wake-on-WLAN support for QCA6390 and WCN6855

* device recovery (firmware restart) support for QCA6390 and WCN6855

wcn36xx

* support for transmit rate reporting to user space

2 years agoath11k: mhi: remove unnecessary goto from ath11k_mhi_start()
Kalle Valo [Tue, 5 Apr 2022 08:26:44 +0000 (11:26 +0300)]
ath11k: mhi: remove unnecessary goto from ath11k_mhi_start()

No need to have goto for a return statement, so simplify the code. While at it,
print warning messages if power up calls fail.

No functional changes.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-4-kvalo@kernel.org
2 years agoath11k: mhi: add error handling for suspend and resume
Kalle Valo [Tue, 5 Apr 2022 08:26:39 +0000 (11:26 +0300)]
ath11k: mhi: add error handling for suspend and resume

While reviewing the mhi.c I noticed we were just ignoring the errors coming
from MHI subsystem during suspend and resume. Add proper checks and warning
messages. Also pass the error value to callers.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-3-kvalo@kernel.org
2 years agoath11k: mhi: remove state machine
Kalle Valo [Fri, 1 Apr 2022 17:30:40 +0000 (20:30 +0300)]
ath11k: mhi: remove state machine

State machines are difficult to understand and in this case it's just useless,
which is shown by the diffstat. So remove it entirely to make the code simpler.

No functional changes.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2

Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401173042.17467-2-kvalo@kernel.org
2 years agortw89: handle potential uninitialized variable
Ping-Ke Shih [Fri, 18 Mar 2022 03:52:02 +0000 (11:52 +0800)]
rtw89: handle potential uninitialized variable

The smatch reports:
 rtw8852a.c:1857 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.
 rtw8852a.c:1858 rtw8852a_btc_set_wl_txpwr_ctrl() error: uninitialized symbol '_cur'.

This is because rtw89_mac_txpwr_read32() can possibly return before setting
argument _cur, and the caller will use the uninitialized value. To fix this
problem, check the return value of rtw89_mac_txpwr_read32().

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318035202.42437-1-pkshih@realtek.com
2 years agortw89: read RX bandwidth from v1 type RX descriptor
Ping-Ke Shih [Fri, 18 Mar 2022 02:32:14 +0000 (10:32 +0800)]
rtw89: read RX bandwidth from v1 type RX descriptor

8852C uses different fields to represent RX bandwidth. Since other fields
are the same, I check chip_id to get bandwidth instead of creating another
v1 function.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-12-pkshih@realtek.com
2 years agortw89: support hardware generate security header
Ping-Ke Shih [Fri, 18 Mar 2022 02:32:13 +0000 (10:32 +0800)]
rtw89: support hardware generate security header

The newer chip will generate security header itself, so don't set
IEEE80211_KEY_FLAG_GENERATE_IV in this kind of chip. But, it needs to fill
key_index, PN and 802.11 header length to TX descriptor, and then hardware
uses these to generate security header.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-11-pkshih@realtek.com
2 years agortw89: support variant of fill_txdesc
Ping-Ke Shih [Fri, 18 Mar 2022 02:32:12 +0000 (10:32 +0800)]
rtw89: support variant of fill_txdesc

The txdesc is descriptor related to skb->data. The v1 version contains
8 dwords txwd_body and 6 dwords txwd_info, and the format is also different
from original one.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-10-pkshih@realtek.com
2 years agortw89: pci: support variant of fill_txaddr_info
Ping-Ke Shih [Fri, 18 Mar 2022 02:32:11 +0000 (10:32 +0800)]
rtw89: pci: support variant of fill_txaddr_info

The txaddr_info is used to fill the DMA address of skb->data. The v1
version can support up to 10 entries, but the maximum size of each entry
is 2047, so it fill more than one entry for large packet, like 3000 bytes.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-9-pkshih@realtek.com
2 years agortw89: add chip_info::h2c_desc_size/fill_txdesc_fwcmd to support new chips
Ping-Ke Shih [Fri, 18 Mar 2022 02:32:10 +0000 (10:32 +0800)]
rtw89: add chip_info::h2c_desc_size/fill_txdesc_fwcmd to support new chips

8852A and 8852C use different H2C header and size, so add h2c_desc_size
to allocate different header size and fill content by fill_txdesc_fwcmd.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-8-pkshih@realtek.com
2 years agortw89: disabled IGI configuration for unsupported hardware
Johnson Lin [Fri, 18 Mar 2022 02:32:09 +0000 (10:32 +0800)]
rtw89: disabled IGI configuration for unsupported hardware

Bypass IGI, known as Rx gain, adjustment flow for incompatible hardware
architectures.

Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-7-pkshih@realtek.com
2 years agortw89: packed IGI configuration flow into function for DIG feature
Johnson Lin [Fri, 18 Mar 2022 02:32:08 +0000 (10:32 +0800)]
rtw89: packed IGI configuration flow into function for DIG feature

Refinement of DIG flow, a mechanism to adjust Rx gain for better Rx
performance, by packing IGI(initial gain index) configuration flow into
one function.

Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-6-pkshih@realtek.com
2 years agortw89: regd: update mapping table to R59-R32
Zong-Zhe Yang [Fri, 18 Mar 2022 02:32:07 +0000 (10:32 +0800)]
rtw89: regd: update mapping table to R59-R32

Update notes:
Configure rtw89_regulatory for 6G band according to country.
Adjust country GB to use RTW89_UK entry on all bands.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-5-pkshih@realtek.com
2 years agortw89: regd: consider 6G band
Zong-Zhe Yang [Fri, 18 Mar 2022 02:32:06 +0000 (10:32 +0800)]
rtw89: regd: consider 6G band

Wrap regd debug dump into a macro and add dump for 6G band field.
Extend the macro used to configure regd table to account for multiple
bands beyond 2G and 5G.

And the follow-up commit will configure the corresponding values for
6G band into regd table.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-4-pkshih@realtek.com
2 years agortw89: 8852a: update txpwr tables to HALRF_027_00_038
Zong-Zhe Yang [Fri, 18 Mar 2022 02:32:05 +0000 (10:32 +0800)]
rtw89: 8852a: update txpwr tables to HALRF_027_00_038

Update notes:
TX power by rate table is not changed.
TX power limit table configures values for UK.
TX power limit RU table configures values for UK.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-3-pkshih@realtek.com
2 years agortw89: add UK to regulation type
Zong-Zhe Yang [Fri, 18 Mar 2022 02:32:04 +0000 (10:32 +0800)]
rtw89: add UK to regulation type

Add RTW89_UK to enum rtw89_regulation_type.
The follow-up commit will configure the corresponding values for it
to TX power tables.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318023214.32411-2-pkshih@realtek.com
2 years agortw89: reduce export symbol number of mac size and quota
Ping-Ke Shih [Tue, 15 Mar 2022 01:55:22 +0000 (09:55 +0800)]
rtw89: reduce export symbol number of mac size and quota

An export symbol costs about 40 bytes (in x86 with gcc), so use a structure
containing these small arrays to reduce code size.

   text    data     bss     dec     hex filename
  34932    1410       0   36342    8df6 mac.o (before)
  34276    1258       0   35534    8ace mac.o (after)

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220315015522.11366-1-pkshih@realtek.com
2 years agortw89: support FW crash simulation
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:50 +0000 (15:12 +0800)]
rtw89: support FW crash simulation

Originally, there is already a mechanism, SER (system error recover),
to deal with HW/FW recovery. After FW v0.13.36.0, FW supports a H2C
(host to chip) command to make a CPU exception. Then, SER is supposed
to catch this FW crash and do L2 reset. This feature is a simulation
to verify if flow of recovering from FW crash works.

Usage of fw_crash debugfs is as the following.
$ echo 1 > fw_crash // trigger FW crash and wait SER handling
$ cat fw_crash // return 0 if restart has been done

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-9-pkshih@realtek.com
2 years agortw89: reconstruct fw feature
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:49 +0000 (15:12 +0800)]
rtw89: reconstruct fw feature

As the fw features gradually increase, it would be better that
we have a set of methods to maintain fw features instead of using
scattered bool variables.

We reconstruct the way fw recognize features, and introduce
RTW89_CHK_FW_FEATURE() / RTW89_SET_FW_FEATURE() to check / set
fw features for uses.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-8-pkshih@realtek.com
2 years agortw89: ser: dump fw backtrace while L2 reset
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:48 +0000 (15:12 +0800)]
rtw89: ser: dump fw backtrace while L2 reset

Read FW backtrace entry through FW reserved payload engine, and then
add FW backtrace dump during SER (system error recover) L2 reset process.
It contains a list of RA (return address) and SP (stack pointer) which
gives us a chance to trace back the call stack of FW.

Moreover, if core dump might have wrong content due to error during
dumping, we won't invoke device core dump framework. For this case,
rtw89_ser_cd_free() is added to free buffer by ourselves.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-7-pkshih@realtek.com
2 years agortw89: ser: dump memory for fw payload engine while L2 reset
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:47 +0000 (15:12 +0800)]
rtw89: ser: dump memory for fw payload engine while L2 reset

When FW encounters exception or assertion, SER L2 reset process will start.
It will dump some error information and re-download FW eventually. Since
such errors are usually critical, we would like to keep more information
about error to increase possibility of analysis and debugging FW. We first
add FW payload engine (fw reserved playoad engine, fw_rsvd_ple) memory
dump. FW will record things like CPU registers, backtrace entry, etc. in it
for debugging.

Moreover, device core dump framework is used and wrapped to collect kinds
of dumps during SER L2 reset process.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-6-pkshih@realtek.com
2 years agortw89: ser: control hci interrupts on/off by state
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:46 +0000 (15:12 +0800)]
rtw89: ser: control hci interrupts on/off by state

While SER (system error recover) is processing, it's supposed to mean
something is under recovery. So, disable interrupts (excluding the one
of halt which could be used during SER) to avoid unexpected behavior.
And then, enable interrupts after SER is done.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-5-pkshih@realtek.com
2 years agortw89: mac: correct decision on error status by scenario
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:45 +0000 (15:12 +0800)]
rtw89: mac: correct decision on error status by scenario

The raw error code might combine error scenario and error status.
But, the error scenario isn't parsed previously. It makes us mishandle
cpu exception and assertion. Now, we correct the error status for them.

Besides, a few uses of error status are refined.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-4-pkshih@realtek.com
2 years agortw89: mac: move table of mem base addr to common
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:44 +0000 (15:12 +0800)]
rtw89: mac: move table of mem base addr to common

Previously, mac_mem_base_addr_table was declared in debug.c locally
because it's only used via debugfs to dump mac memory. Now, we plan to
refine SER (system error recover) flow which will also need to dump mac
memory to somewhere as information for error which is catched. So, we
move mac_mem_base_addr_table to mac.c rtw89_mac_mem_base_addrs earlier
as common code.

(no logic is changed)

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-3-pkshih@realtek.com
2 years agortw89: ser: fix CAM leaks occurring in L2 reset
Zong-Zhe Yang [Mon, 14 Mar 2022 07:12:43 +0000 (15:12 +0800)]
rtw89: ser: fix CAM leaks occurring in L2 reset

The CAM, meaning address CAM and bssid CAM here, will get leaks during
SER (system error recover) L2 reset process and ieee80211_restart_hw()
which is called by L2 reset process eventually.

The normal flow would be like
-> add interface (acquire 1)
-> enter ips (release 1)
-> leave ips (acquire 1)
-> connection (occupy 1) <(A) 1 leak after L2 reset if non-sec connection>

The ieee80211_restart_hw() flow (under connection)
-> ieee80211 reconfig
-> add interface (acquire 1)
-> leave ips (acquire 1)
-> connection (occupy (A) + 2) <(B) 1 more leak>

Originally, CAM is released before HW restart only if connection is under
security. Now, release CAM whatever connection it is to fix leak in (A).
OTOH, check if CAM is already valid to avoid acquiring multiple times to
fix (B).

Besides, if AP mode, release address CAM of all stations before HW restart.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220314071250.40292-2-pkshih@realtek.com
2 years agortw88: change idle mode condition during hw_scan
Po-Hao Huang [Fri, 18 Mar 2022 03:43:16 +0000 (11:43 +0800)]
rtw88: change idle mode condition during hw_scan

Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.

Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318034316.40720-1-pkshih@realtek.com
2 years agoiwlwifi: mei: Replace zero-length array with flexible-array member
Gustavo A. R. Silva [Wed, 16 Feb 2022 19:50:30 +0000 (13:50 -0600)]
iwlwifi: mei: Replace zero-length array with flexible-array member

There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/78
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220216195030.GA904170@embeddedor
2 years agoiwlwifi: fw: Replace zero-length arrays with flexible-array members
Gustavo A. R. Silva [Wed, 16 Feb 2022 19:50:15 +0000 (13:50 -0600)]
iwlwifi: fw: Replace zero-length arrays with flexible-array members

There is a regular need in the kernel to provide a way to declare
having a dynamically sized set of trailing elements in a structure.
Kernel code should always use “flexible array members”[1] for these
cases. The older style of one-element or zero-length arrays should
no longer be used[2].

[1] https://en.wikipedia.org/wiki/Flexible_array_member
[2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays

Link: https://github.com/KSPP/linux/issues/78
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220216195015.GA904148@embeddedor
2 years agonet: ensure net_todo_list is processed quickly
Johannes Berg [Mon, 4 Apr 2022 09:38:47 +0000 (11:38 +0200)]
net: ensure net_todo_list is processed quickly

In [1], Will raised a potential issue that the cfg80211 code,
which does (from a locking perspective)

  rtnl_lock()
  wiphy_lock()
  rtnl_unlock()

might be suspectible to ABBA deadlocks, because rtnl_unlock()
calls netdev_run_todo(), which might end up calling rtnl_lock()
again, which could then deadlock (see the comment in the code
added here for the scenario).

Some back and forth and thinking ensued, but clearly this can't
happen if the net_todo_list is empty at the rtnl_unlock() here.
Clearly, the code here cannot actually put an entry on it, and
all other users of rtnl_unlock() will empty it since that will
always go through netdev_run_todo(), emptying the list.

So the only other way to get there would be to add to the list
and then unlock the RTNL without going through rtnl_unlock(),
which is only possible through __rtnl_unlock(). However, this
isn't exported and not used in many places, and none of them
seem to be able to unregister before using it.

Therefore, add a WARN_ON() in the code to ensure this invariant
won't be broken, so that the cfg80211 (or any similar) code
stays safe.

[1] https://lore.kernel.org/r/Yjzpo3TfZxtKPMAG@google.com

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20220404113847.0ee02e4a70da.Ic73d206e217db20fd22dcec14fe5442ca732804b@changeid
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2 years agomlxsw: spectrum_router: simplify list unwinding
Tom Rix [Sat, 2 Apr 2022 12:15:16 +0000 (08:15 -0400)]
mlxsw: spectrum_router: simplify list unwinding

The setting of i here
err_nexthop6_group_get:
i = nrt6;
Is redundant, i is already nrt6.  So remove
this statement.

The for loop for the unwinding
err_rt6_create:
for (i--; i >= 0; i--) {
Is equivelent to
for (; i > 0; i--) {

Two consecutive labels can be reduced to one.

Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220402121516.2750284-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2 years agoath11k: fix driver initialization failure with WoW unsupported hw
Nagarajan Maran [Fri, 1 Apr 2022 11:53:10 +0000 (14:53 +0300)]
ath11k: fix driver initialization failure with WoW unsupported hw

In the "ath11k_wow_init", error value "EINVAL" is returned
when the check for firmware support of WoW feature fails,
which in turn stops the driver initialization.

Warning message:
[   31.040144] ------------[ cut here ]------------
[   31.040185] WARNING: CPU: 1 PID: 51 at drivers/net/wireless/ath/ath11k/wow.c:813 ath11k_wow_init+0xc8/0x13a8 [ath11k]
[   31.043846] Modules linked in: ath11k_pci ath11k qmi_helpers
[   31.054341] CPU: 1 PID: 51 Comm: kworker/u8:1 Tainted: G        W 5.17.0-wt-ath-594817-ga7f6aa925cf8-dirty #17
[   31.060078] Hardware name: Qualcomm Technologies, Inc. IPQ8074/AP-HK10-C2 (DT)
[   31.070578] Workqueue: ath11k_qmi_driver_event ath11k_qmi_driver_event_work [ath11k]
[   31.077782] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   31.085676] pc : ath11k_wow_init+0xc8/0x13a8 [ath11k]
[   31.092359] lr : ath11k_mac_register+0x548/0xb98 [ath11k]
[   31.097567] sp : ffff80000aa13c40
[   31.102944] x29: ffff80000aa13c40 x28: ffff800009184390 x27: ffff000002959f20
[   31.106251] x26: ffff000002828000 x25: ffff000002830000 x24: ffff000002830000
[   31.113369] x23: ffff000002820000 x22: ffff00000282854c x21: 0000000000000000
[   31.120487] x20: ffff00000295cf20 x19: ffff000002828540 x18: 0000000000000031
[   31.127605] x17: 0000000000000004 x16: ffff0000028285fc x15: ffff00000295b040
[   31.134723] x14: 0000000000000067 x13: ffff00000282859c x12: 000000000000000d
[   31.141840] x11: 0000000000000018 x10: 0000000000000004 x9 : 0000000000000000
[   31.148959] x8 : ffff00000289d680 x7 : 0000000000000000 x6 : 000000000000003f
[   31.156077] x5 : 0000000000000040 x4 : 0000000000000000 x3 : ffff000002820968
[   31.163196] x2 : 0000000000000080 x1 : 0080008af9981779 x0 : ffff000002959f20
[   31.170314] Call trace:
[   31.177421]  ath11k_wow_init+0xc8/0x13a8 [ath11k]
[   31.179684]  ath11k_core_qmi_firmware_ready+0x430/0x5e0 [ath11k]
[   31.184548]  ath11k_qmi_driver_event_work+0x16c/0x4f8 [ath11k]
[   31.190623]  process_one_work+0x134/0x350
[   31.196262]  worker_thread+0x12c/0x450
[   31.200340]  kthread+0xf4/0x110
[   31.203986]  ret_from_fork+0x10/0x20
[   31.207026] ---[ end trace 0000000000000000 ]---
[   31.210894] ath11k_pci 0000:01:00.0: failed to init wow: -22
[   31.215467] ath11k_pci 0000:01:00.0: failed register the radio with mac80211: -22
[   31.221117] ath11k_pci 0000:01:00.0: failed to create pdev core: -22

Fix this by returning value "0" when FW doesn't support WoW
to allow driver to proceed with initialize sequence and also
remove the unnecessary "WARN_ON".

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

Fixes: ba9177fcef21 ("ath11k: Add basic WoW functionalities")
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331073110.3846-1-quic_nmaran@quicinc.com
2 years agoath11k: Remove unnecessary delay in ath11k_core_suspend
Baochen Qiang [Fri, 1 Apr 2022 11:53:10 +0000 (14:53 +0300)]
ath11k: Remove unnecessary delay in ath11k_core_suspend

The intended delay in ath11k_core_suspend is introduced in commit
d1b0c33850d2 ("ath11k: implement suspend for QCA6390 PCI devices"),
now with ath11k_mac_wait_tx_complete added in commit ba9177fcef21
("ath11k: Add basic WoW functionalities"), that delay is not
necessary now, so remove it.

This is found in code review.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331002105.1162099-1-quic_bqiang@quicinc.com
2 years agoath11k: Change max no of active probe SSID and BSSID to fw capability
Karthikeyan Kathirvel [Fri, 1 Apr 2022 11:53:09 +0000 (14:53 +0300)]
ath11k: Change max no of active probe SSID and BSSID to fw capability

The maximum number of SSIDs in a for active probe requests is currently
reported as 16 (WLAN_SCAN_PARAMS_MAX_SSID) when registering the driver.
The scan_req_params structure only has the capacity to hold 10 SSIDs.
This leads to a buffer overflow which can be triggered from
wpa_supplicant in userspace. When copying the SSIDs into the
scan_req_params structure in the ath11k_mac_op_hw_scan route, it can
overwrite the extraie pointer.

Firmware supports 16 ssid * 4 bssid, for each ssid 4 bssid combo probe
request will be sent, so totally 64 probe requests supported. So
set both max ssid and bssid to 16 and 4 respectively. Remove the
redundant macros of ssid and bssid.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01300-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220329150221.21907-1-quic_kathirve@quicinc.com
2 years agoath11k: Remove core PCI references from PCI common code
Manikanta Pubbisetty [Fri, 1 Apr 2022 11:53:08 +0000 (14:53 +0300)]
ath11k: Remove core PCI references from PCI common code

Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.

Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com
2 years agoath11k: Refactor MSI logic to support WCN6750
Manikanta Pubbisetty [Fri, 1 Apr 2022 11:53:08 +0000 (14:53 +0300)]
ath11k: Refactor MSI logic to support WCN6750

Refactor MSI logic in order to support hybrid bus devices
like WCN6750.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-5-quic_mpubbise@quicinc.com
2 years agoath11k: Choose MSI config based on HW revision
Manikanta Pubbisetty [Fri, 1 Apr 2022 11:53:08 +0000 (14:53 +0300)]
ath11k: Choose MSI config based on HW revision

Instead of selecting MSI config based on magic numbers, make
the assignment based on HW revision. The logic is similar to
the selection of HW params. This improves readability of the
code and also simplifies new additions.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-4-quic_mpubbise@quicinc.com
2 years agoath11k: Refactor PCI code to support WCN6750
Manikanta Pubbisetty [Fri, 1 Apr 2022 11:53:08 +0000 (14:53 +0300)]
ath11k: Refactor PCI code to support WCN6750

Unlike other ATH11K PCIe devices which are enumerated by APSS
processor (Application Processor SubSystem), WCN6750 gets
enumerated by the WPSS Q6 processor (Wireless Processor SubSystem);
In simple terms, though WCN6750 is PCIe device, it is not attached
to the APSS processor, APSS will not know of such a device being
present in the system and therefore WCN6750 will be registered as
a platform device to the kernel core like other supported AHB
devices.

WCN6750 needs both AHB and PCI APIs for it's operation, it uses
AHB APIs for device probe/boot and PCI APIs for device setup and
register accesses. Because of this nature, it is referred as a
hybrid bus device.

Refactor PCI code to support hybrid bus devices like WCN6750.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-3-quic_mpubbise@quicinc.com
2 years agoath11k: PCI changes to support WCN6750
Manikanta Pubbisetty [Fri, 1 Apr 2022 11:53:08 +0000 (14:53 +0300)]
ath11k: PCI changes to support WCN6750

In order to add the support for WCN6750 in ATH11K , it is
required to move certain PCI definitions to the header file.
As a result, add ATH11K_PCI_* prefix to these definitions.

Also, change the scope of certain PCI APIs that are required
to enable WCN6750 from static to global.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1

Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-2-quic_mpubbise@quicinc.com
2 years agoLinux 5.18-rc1
Linus Torvalds [Sun, 3 Apr 2022 21:08:21 +0000 (14:08 -0700)]
Linux 5.18-rc1

2 years agoMerge tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt...
Linus Torvalds [Sun, 3 Apr 2022 19:26:01 +0000 (12:26 -0700)]
Merge tag 'trace-v5.18-2' of git://git./linux/kernel/git/rostedt/linux-trace

Pull more tracing updates from Steven Rostedt:

 - Rename the staging files to give them some meaning. Just
   stage1,stag2,etc, does not show what they are for

 - Check for NULL from allocation in bootconfig

 - Hold event mutex for dyn_event call in user events

 - Mark user events to broken (to work on the API)

 - Remove eBPF updates from user events

 - Remove user events from uapi header to keep it from being installed.

 - Move ftrace_graph_is_dead() into inline as it is called from hot
   paths and also convert it into a static branch.

* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Move user_events.h temporarily out of include/uapi
  ftrace: Make ftrace_graph_is_dead() a static branch
  tracing: Set user_events to BROKEN
  tracing/user_events: Remove eBPF interfaces
  tracing/user_events: Hold event_mutex during dyn_event_add
  proc: bootconfig: Add null pointer check
  tracing: Rename the staging files for trace_events

2 years agoMerge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Linus Torvalds [Sun, 3 Apr 2022 19:21:14 +0000 (12:21 -0700)]
Merge tag 'clk-for-linus' of git://git./linux/kernel/git/clk/linux

Pull clk fix from Stephen Boyd:
 "A single revert to fix a boot regression seen when clk_put() started
  dropping rate range requests. It's best to keep various systems
  booting so we'll kick this out and try again next time"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  Revert "clk: Drop the rate range on clk_put()"

2 years agoMerge tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sun, 3 Apr 2022 19:15:47 +0000 (12:15 -0700)]
Merge tag 'x86-urgent-2022-04-03' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Thomas Gleixner:
 "A set of x86 fixes and updates:

   - Make the prctl() for enabling dynamic XSTATE components correct so
     it adds the newly requested feature to the permission bitmap
     instead of overwriting it. Add a selftest which validates that.

   - Unroll string MMIO for encrypted SEV guests as the hypervisor
     cannot emulate it.

   - Handle supervisor states correctly in the FPU/XSTATE code so it
     takes the feature set of the fpstate buffer into account. The
     feature sets can differ between host and guest buffers. Guest
     buffers do not contain supervisor states. So far this was not an
     issue, but with enabling PASID it needs to be handled in the buffer
     offset calculation and in the permission bitmaps.

   - Avoid a gazillion of repeated CPUID invocations in by caching the
     values early in the FPU/XSTATE code.

   - Enable CONFIG_WERROR in x86 defconfig.

   - Make the X86 defconfigs more useful by adapting them to Y2022
     reality"

* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/fpu/xstate: Consolidate size calculations
  x86/fpu/xstate: Handle supervisor states in XSTATE permissions
  x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
  x86/fpu: Cache xfeature flags from CPUID
  x86/fpu/xsave: Initialize offset/size cache early
  x86/fpu: Remove unused supervisor only offsets
  x86/fpu: Remove redundant XCOMP_BV initialization
  x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
  x86/config: Make the x86 defconfigs a bit more usable
  x86/defconfig: Enable WERROR
  selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
  x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation

2 years agoMerge tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sun, 3 Apr 2022 19:08:26 +0000 (12:08 -0700)]
Merge tag 'core-urgent-2022-04-03' of git://git./linux/kernel/git/tip/tip

Pull RT signal fix from Thomas Gleixner:
 "Revert the RT related signal changes. They need to be reworked and
  generalized"

* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"

2 years agoMerge tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping
Linus Torvalds [Sun, 3 Apr 2022 17:31:00 +0000 (10:31 -0700)]
Merge tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping

Pull more dma-mapping updates from Christoph Hellwig:

 - fix a regression in dma remap handling vs AMD memory encryption (me)

 - finally kill off the legacy PCI DMA API (Christophe JAILLET)

* tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping:
  dma-mapping: move pgprot_decrypted out of dma_pgprot
  PCI/doc: cleanup references to the legacy PCI DMA API
  PCI: Remove the deprecated "pci-dma-compat.h" API

2 years agoMerge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Linus Torvalds [Sun, 3 Apr 2022 17:17:48 +0000 (10:17 -0700)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm

Pull ARM fixes from Russell King:

 - avoid unnecessary rebuilds for library objects

 - fix return value of __setup handlers

 - fix invalid input check for "crashkernel=" kernel option

 - silence KASAN warnings in unwind_frame

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
  ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0'
  ARM: 9187/1: JIVE: fix return value of __setup handler
  ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects

2 years agoRevert "clk: Drop the rate range on clk_put()"
Stephen Boyd [Sun, 3 Apr 2022 02:28:18 +0000 (19:28 -0700)]
Revert "clk: Drop the rate range on clk_put()"

This reverts commit 7dabfa2bc4803eed83d6f22bd6f045495f40636b. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.

Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org
2 years agoMerge tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux...
Linus Torvalds [Sat, 2 Apr 2022 19:57:17 +0000 (12:57 -0700)]
Merge tag 'perf-tools-for-v5.18-2022-04-02' of git://git./linux/kernel/git/acme/linux

Pull more perf tools updates from Arnaldo Carvalho de Melo:

 - Avoid SEGV if core.cpus isn't set in 'perf stat'.

 - Stop depending on .git files for building PERF-VERSION-FILE, used in
   'perf --version', fixing some perf tools build scenarios.

 - Convert tracepoint.py example to python3.

 - Update UAPI header copies from the kernel sources: socket,
   mman-common, msr-index, KVM, i915 and cpufeatures.

 - Update copy of libbpf's hashmap.c.

 - Directly return instead of using local ret variable in
   evlist__create_syswide_maps(), found by coccinelle.

* tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf python: Convert tracepoint.py example to python3
  perf evlist: Directly return instead of using local ret variable
  perf cpumap: More cpu map reuse by merge.
  perf cpumap: Add is_subset function
  perf evlist: Rename cpus to user_requested_cpus
  perf tools: Stop depending on .git files for building PERF-VERSION-FILE
  tools headers cpufeatures: Sync with the kernel sources
  tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
  tools headers UAPI: Sync linux/kvm.h with the kernel sources
  tools kvm headers arm64: Update KVM headers from the kernel sources
  tools arch x86: Sync the msr-index.h copy with the kernel sources
  tools headers UAPI: Sync asm-generic/mman-common.h with the kernel
  perf beauty: Update copy of linux/socket.h with the kernel sources
  perf tools: Update copy of libbpf's hashmap.c
  perf stat: Avoid SEGV if core.cpus isn't set

2 years agoMerge tag 'kbuild-fixes-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masah...
Linus Torvalds [Sat, 2 Apr 2022 19:33:31 +0000 (12:33 -0700)]
Merge tag 'kbuild-fixes-v5.18' of git://git./linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix empty $(PYTHON) expansion.

 - Fix UML, which got broken by the attempt to suppress Clang warnings.

 - Fix warning message in modpost.

* tag 'kbuild-fixes-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  modpost: restore the warning message for missing symbol versions
  Revert "um: clang: Strip out -mno-global-merge from USER_CFLAGS"
  kbuild: Remove '-mno-global-merge'
  kbuild: fix empty ${PYTHON} in scripts/link-vmlinux.sh
  kconfig: remove stale comment about removed kconfig_print_symbol()

2 years agoMerge tag 'mips_5.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Linus Torvalds [Sat, 2 Apr 2022 19:14:38 +0000 (12:14 -0700)]
Merge tag 'mips_5.18_1' of git://git./linux/kernel/git/mips/linux

Pull MIPS fixes from Thomas Bogendoerfer:

 - build fix for gpio

 - fix crc32 build problems

 - check for failed memory allocations

* tag 'mips_5.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: crypto: Fix CRC32 code
  MIPS: rb532: move GPIOD definition into C-files
  MIPS: lantiq: check the return value of kzalloc()
  mips: sgi-ip22: add a check for the return of kzalloc()

2 years agoMerge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Linus Torvalds [Sat, 2 Apr 2022 19:09:02 +0000 (12:09 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull kvm fixes from Paolo Bonzini:

 - Only do MSR filtering for MSRs accessed by rdmsr/wrmsr

 - Documentation improvements

 - Prevent module exit until all VMs are freed

 - PMU Virtualization fixes

 - Fix for kvm_irq_delivery_to_apic_fast() NULL-pointer dereferences

 - Other miscellaneous bugfixes

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (42 commits)
  KVM: x86: fix sending PV IPI
  KVM: x86/mmu: do compare-and-exchange of gPTE via the user address
  KVM: x86: Remove redundant vm_entry_controls_clearbit() call
  KVM: x86: cleanup enter_rmode()
  KVM: x86: SVM: fix tsc scaling when the host doesn't support it
  kvm: x86: SVM: remove unused defines
  KVM: x86: SVM: move tsc ratio definitions to svm.h
  KVM: x86: SVM: fix avic spec based definitions again
  KVM: MIPS: remove reference to trap&emulate virtualization
  KVM: x86: document limitations of MSR filtering
  KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
  KVM: x86/emulator: Emulate RDPID only if it is enabled in guest
  KVM: x86/pmu: Fix and isolate TSX-specific performance event logic
  KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
  KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
  KVM: x86: Trace all APICv inhibit changes and capture overall status
  KVM: x86: Add wrappers for setting/clearing APICv inhibits
  KVM: x86: Make APICv inhibit reasons an enum and cleanup naming
  KVM: X86: Handle implicit supervisor access with SMAP
  KVM: X86: Rename variable smap to not_smap in permission_fault()
  ...

2 years agomodpost: restore the warning message for missing symbol versions
Masahiro Yamada [Fri, 1 Apr 2022 15:56:10 +0000 (00:56 +0900)]
modpost: restore the warning message for missing symbol versions

This log message was accidentally chopped off.

I was wondering why this happened, but checking the ML log, Mark
precisely followed my suggestion [1].

I just used "..." because I was too lazy to type the sentence fully.
Sorry for the confusion.

[1]: https://lore.kernel.org/all/CAK7LNAR6bXXk9-ZzZYpTqzFqdYbQsZHmiWspu27rtsFxvfRuVA@mail.gmail.com/

Fixes: 4a6795933a89 ("kbuild: modpost: Explicitly warn about unprototyped symbols")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
2 years agoMerge tag 'for-5.18/drivers-2022-04-02' of git://git.kernel.dk/linux-block
Linus Torvalds [Sat, 2 Apr 2022 18:03:03 +0000 (11:03 -0700)]
Merge tag 'for-5.18/drivers-2022-04-02' of git://git.kernel.dk/linux-block

Pull block driver fix from Jens Axboe:
 "Got two reports on nbd spewing warnings on load now, which is a
  regression from a commit that went into your tree yesterday.

  Revert the problematic change for now"

* tag 'for-5.18/drivers-2022-04-02' of git://git.kernel.dk/linux-block:
  Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"

2 years agoMerge tag 'pci-v5.18-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git...
Linus Torvalds [Sat, 2 Apr 2022 17:54:52 +0000 (10:54 -0700)]
Merge tag 'pci-v5.18-changes-2' of git://git./linux/kernel/git/helgaas/pci

Pull pci fix from Bjorn Helgaas:

 - Fix Hyper-V "defined but not used" build issue added during merge
   window (YueHaibing)

* tag 'pci-v5.18-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: hv: Remove unused hv_set_msi_entry_from_desc()

2 years agoMerge tag 'tag-chrome-platform-for-v5.18' of git://git.kernel.org/pub/scm/linux/kerne...
Linus Torvalds [Sat, 2 Apr 2022 17:44:18 +0000 (10:44 -0700)]
Merge tag 'tag-chrome-platform-for-v5.18' of git://git./linux/kernel/git/chrome-platform/linux

Pull chrome platform updates from Benson Leung:
 "cros_ec_typec:

   - Check for EC device - Fix a crash when using the cros_ec_typec
     driver on older hardware not capable of typec commands

   - Make try power role optional

   - Mux configuration reorganization series from Prashant

  cros_ec_debugfs:

   - Fix use after free. Thanks Tzung-bi

  sensorhub:

   - cros_ec_sensorhub fixup - Split trace include file

  misc:

   - Add new mailing list for chrome-platform development:

chrome-platform@lists.linux.dev

     Now with patchwork!"

* tag 'tag-chrome-platform-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
  platform/chrome: cros_ec_debugfs: detach log reader wq from devm
  platform: chrome: Split trace include file
  platform/chrome: cros_ec_typec: Update mux flags during partner removal
  platform/chrome: cros_ec_typec: Configure muxes at start of port update
  platform/chrome: cros_ec_typec: Get mux state inside configure_mux
  platform/chrome: cros_ec_typec: Move mux flag checks
  platform/chrome: cros_ec_typec: Check for EC device
  platform/chrome: cros_ec_typec: Make try power role optional
  MAINTAINERS: platform-chrome: Add new chrome-platform@lists.linux.dev list

2 years agoRevert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"
Jens Axboe [Sat, 2 Apr 2022 17:40:23 +0000 (11:40 -0600)]
Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"

This reverts commit 6d35d04a9e18990040e87d2bbf72689252669d54.

Both Gabriel and Borislav report that this commit casues a regression
with nbd:

sysfs: cannot create duplicate filename '/dev/block/43:0'

Revert it before 5.18-rc1 and we'll investigage this separately in
due time.

Link: https://lore.kernel.org/all/YkiJTnFOt9bTv6A2@zn.tnic/
Reported-by: Gabriel L. Somlo <somlo@cmu.edu>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
2 years agowatch_queue: Free the page array when watch_queue is dismantled
Eric Dumazet [Mon, 28 Mar 2022 17:07:04 +0000 (18:07 +0100)]
watch_queue: Free the page array when watch_queue is dismantled

Commit 7ea1a0124b6d ("watch_queue: Free the alloc bitmap when the
watch_queue is torn down") took care of the bitmap, but not the page
array.

  BUG: memory leak
  unreferenced object 0xffff88810d9bc140 (size 32):
  comm "syz-executor335", pid 3603, jiffies 4294946994 (age 12.840s)
  hex dump (first 32 bytes):
    40 a7 40 04 00 ea ff ff 00 00 00 00 00 00 00 00  @.@.............
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
     kmalloc_array include/linux/slab.h:621 [inline]
     kcalloc include/linux/slab.h:652 [inline]
     watch_queue_set_size+0x12f/0x2e0 kernel/watch_queue.c:251
     pipe_ioctl+0x82/0x140 fs/pipe.c:632
     vfs_ioctl fs/ioctl.c:51 [inline]
     __do_sys_ioctl fs/ioctl.c:874 [inline]
     __se_sys_ioctl fs/ioctl.c:860 [inline]
     __x64_sys_ioctl+0xfc/0x140 fs/ioctl.c:860
     do_syscall_x64 arch/x86/entry/common.c:50 [inline]

Reported-by: syzbot+25ea042ae28f3888727a@syzkaller.appspotmail.com
Fixes: c73be61cede5 ("pipe: Add general notification queue support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20220322004654.618274-1-eric.dumazet@gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2 years agotracing: mark user_events as BROKEN
Steven Rostedt (Google) [Fri, 1 Apr 2022 18:39:03 +0000 (14:39 -0400)]
tracing: mark user_events as BROKEN

After being merged, user_events become more visible to a wider audience
that have concerns with the current API.

It is too late to fix this for this release, but instead of a full
revert, just mark it as BROKEN (which prevents it from being selected in
make config).  Then we can work finding a better API.  If that fails,
then it will need to be completely reverted.

To not have the code silently bitrot, still allow building it with
COMPILE_TEST.

And to prevent the uapi header from being installed, then later changed,
and then have an old distro user space see the old version, move the
header file out of the uapi directory.

Surround the include with CONFIG_COMPILE_TEST to the current location,
but when the BROKEN tag is taken off, it will use the uapi directory,
and fail to compile.  This is a good way to remind us to move the header
back.

Link: https://lore.kernel.org/all/20220330155835.5e1f6669@gandalf.local.home
Link: https://lkml.kernel.org/r/20220330201755.29319-1-mathieu.desnoyers@efficios.com
Suggested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2 years agotracing: Move user_events.h temporarily out of include/uapi
Steven Rostedt (Google) [Fri, 1 Apr 2022 18:39:03 +0000 (14:39 -0400)]
tracing: Move user_events.h temporarily out of include/uapi

While user_events API is under development and has been marked for broken
to not let the API become fixed, move the header file out of the uapi
directory. This is to prevent it from being installed, then later changed,
and then have an old distro user space update with a new kernel, where
applications see the user_events being available, but the old header is in
place, and then they get compiled incorrectly.

Also, surround the include with CONFIG_COMPILE_TEST to the current
location, but when the BROKEN tag is taken off, it will use the uapi
directory, and fail to compile. This is a good way to remind us to move
the header back.

Link: https://lore.kernel.org/all/20220330155835.5e1f6669@gandalf.local.home
Link: https://lkml.kernel.org/r/20220330201755.29319-1-mathieu.desnoyers@efficios.com
Link: https://lkml.kernel.org/r/20220401143903.188384f3@gandalf.local.home
Suggested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agoftrace: Make ftrace_graph_is_dead() a static branch
Christophe Leroy [Wed, 30 Mar 2022 07:00:19 +0000 (09:00 +0200)]
ftrace: Make ftrace_graph_is_dead() a static branch

ftrace_graph_is_dead() is used on hot paths, it just reads a variable
in memory and is not worth suffering function call constraints.

For instance, at entry of prepare_ftrace_return(), inlining it avoids
saving prepare_ftrace_return() parameters to stack and restoring them
after calling ftrace_graph_is_dead().

While at it using a static branch is even more performant and is
rather well adapted considering that the returned value will almost
never change.

Inline ftrace_graph_is_dead() and replace 'kill_ftrace_graph' bool
by a static branch.

The performance improvement is noticeable.

Link: https://lkml.kernel.org/r/e0411a6a0ed3eafff0ad2bc9cd4b0e202b4617df.1648623570.git.christophe.leroy@csgroup.eu
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agotracing: Set user_events to BROKEN
Steven Rostedt (Google) [Wed, 30 Mar 2022 19:58:35 +0000 (15:58 -0400)]
tracing: Set user_events to BROKEN

After being merged, user_events become more visible to a wider audience
that have concerns with the current API. It is too late to fix this for
this release, but instead of a full revert, just mark it as BROKEN (which
prevents it from being selected in make config). Then we can work finding
a better API. If that fails, then it will need to be completely reverted.

Link: https://lore.kernel.org/all/2059213643.196683.1648499088753.JavaMail.zimbra@efficios.com/
Link: https://lkml.kernel.org/r/20220330155835.5e1f6669@gandalf.local.home
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agotracing/user_events: Remove eBPF interfaces
Beau Belgrave [Tue, 29 Mar 2022 17:30:51 +0000 (10:30 -0700)]
tracing/user_events: Remove eBPF interfaces

Remove eBPF interfaces within user_events to ensure they are fully
reviewed.

Link: https://lore.kernel.org/all/20220329165718.GA10381@kbox/
Link: https://lkml.kernel.org/r/20220329173051.10087-1-beaub@linux.microsoft.com
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agotracing/user_events: Hold event_mutex during dyn_event_add
Beau Belgrave [Mon, 28 Mar 2022 22:32:25 +0000 (15:32 -0700)]
tracing/user_events: Hold event_mutex during dyn_event_add

Make sure the event_mutex is properly held during dyn_event_add call.
This is required when adding dynamic events.

Link: https://lkml.kernel.org/r/20220328223225.1992-1-beaub@linux.microsoft.com
Reported-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Beau Belgrave <beaub@linux.microsoft.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agoproc: bootconfig: Add null pointer check
Lv Ruyi [Tue, 29 Mar 2022 10:40:04 +0000 (10:40 +0000)]
proc: bootconfig: Add null pointer check

kzalloc is a memory allocation function which can return NULL when some
internal memory errors happen. It is safer to add null pointer check.

Link: https://lkml.kernel.org/r/20220329104004.2376879-1-lv.ruyi@zte.com.cn
Cc: stable@vger.kernel.org
Fixes: c1a3c36017d4 ("proc: bootconfig: Add /proc/bootconfig to show boot config list")
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agotracing: Rename the staging files for trace_events
Steven Rostedt (Google) [Tue, 29 Mar 2022 20:50:44 +0000 (16:50 -0400)]
tracing: Rename the staging files for trace_events

When looking for implementation of different phases of the creation of the
TRACE_EVENT() macro, it is pretty useless when all helper macro
redefinitions are in files labeled "stageX_defines.h". Rename them to
state which phase the files are for. For instance, when looking for the
defines that are used to create the event fields, seeing
"stage4_event_fields.h" gives the developer a good idea that the defines
are in that file.

Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
2 years agoKVM: x86: fix sending PV IPI
Li RongQing [Wed, 9 Mar 2022 08:35:44 +0000 (16:35 +0800)]
KVM: x86: fix sending PV IPI

If apic_id is less than min, and (max - apic_id) is greater than
KVM_IPI_CLUSTER_SIZE, then the third check condition is satisfied but
the new apic_id does not fit the bitmask.  In this case __send_ipi_mask
should send the IPI.

This is mostly theoretical, but it can happen if the apic_ids on three
iterations of the loop are for example 1, KVM_IPI_CLUSTER_SIZE, 0.

Fixes: aaffcfd1e82 ("KVM: X86: Implement PV IPIs in linux guest")
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Message-Id: <1646814944-51801-1-git-send-email-lirongqing@baidu.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86/mmu: do compare-and-exchange of gPTE via the user address
Paolo Bonzini [Tue, 29 Mar 2022 16:56:24 +0000 (12:56 -0400)]
KVM: x86/mmu: do compare-and-exchange of gPTE via the user address

FNAME(cmpxchg_gpte) is an inefficient mess.  It is at least decent if it
can go through get_user_pages_fast(), but if it cannot then it tries to
use memremap(); that is not just terribly slow, it is also wrong because
it assumes that the VM_PFNMAP VMA is contiguous.

The right way to do it would be to do the same thing as
hva_to_pfn_remapped() does since commit add6a0cd1c5b ("KVM: MMU: try to
fix up page faults before giving up", 2016-07-05), using follow_pte()
and fixup_user_fault() to determine the correct address to use for
memremap().  To do this, one could for example extract hva_to_pfn()
for use outside virt/kvm/kvm_main.c.  But really there is no reason to
do that either, because there is already a perfectly valid address to
do the cmpxchg() on, only it is a userspace address.  That means doing
user_access_begin()/user_access_end() and writing the code in assembly
to handle exceptions correctly.  Worse, the guest PTE can be 8-byte
even on i686 so there is the extra complication of using cmpxchg8b to
account for.  But at least it is an efficient mess.

(Thanks to Linus for suggesting improvement on the inline assembly).

Reported-by: Qiuhao Li <qiuhao@sysec.org>
Reported-by: Gaoning Pan <pgn@zju.edu.cn>
Reported-by: Yongkang Jia <kangel@zju.edu.cn>
Reported-by: syzbot+6cde2282daa792c49ab8@syzkaller.appspotmail.com
Debugged-by: Tadeusz Struk <tadeusz.struk@linaro.org>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Cc: stable@vger.kernel.org
Fixes: bd53cb35a3e9 ("X86/KVM: Handle PFNs outside of kernel reach when touching GPTEs")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: Remove redundant vm_entry_controls_clearbit() call
Zhenzhong Duan [Fri, 11 Mar 2022 10:26:43 +0000 (18:26 +0800)]
KVM: x86: Remove redundant vm_entry_controls_clearbit() call

When emulating exit from long mode, EFER_LMA is cleared with
vmx_set_efer().  This will already unset the VM_ENTRY_IA32E_MODE control
bit as requested by SDM, so there is no need to unset VM_ENTRY_IA32E_MODE
again in exit_lmode() explicitly.  In case EFER isn't supported by
hardware, long mode isn't supported, so exit_lmode() cannot be reached.

Note that, thanks to the shadow controls mechanism, this change doesn't
eliminate vmread or vmwrite.

Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220311102643.807507-3-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: cleanup enter_rmode()
Zhenzhong Duan [Fri, 11 Mar 2022 10:26:42 +0000 (18:26 +0800)]
KVM: x86: cleanup enter_rmode()

vmx_set_efer() sets uret->data but, in fact if the value of uret->data
will be used vmx_setup_uret_msrs() will have rewritten it with the value
returned by update_transition_efer().  uret->data is consumed if and only
if uret->load_into_hardware is true, and vmx_setup_uret_msrs() takes care
of (a) updating uret->data before setting uret->load_into_hardware to true
(b) setting uret->load_into_hardware to false if uret->data isn't updated.

Opportunistically use "vmx" directly instead of redoing to_vmx().

Signed-off-by: Zhenzhong Duan <zhenzhong.duan@intel.com>
Message-Id: <20220311102643.807507-2-zhenzhong.duan@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: SVM: fix tsc scaling when the host doesn't support it
Maxim Levitsky [Tue, 22 Mar 2022 17:24:48 +0000 (19:24 +0200)]
KVM: x86: SVM: fix tsc scaling when the host doesn't support it

It was decided that when TSC scaling is not supported,
the virtual MSR_AMD64_TSC_RATIO should still have the default '1.0'
value.

However in this case kvm_max_tsc_scaling_ratio is not set,
which breaks various assumptions.

Fix this by always calculating kvm_max_tsc_scaling_ratio regardless of
host support.  For consistency, do the same for VMX.

Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-8-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agokvm: x86: SVM: remove unused defines
Maxim Levitsky [Tue, 22 Mar 2022 17:24:47 +0000 (19:24 +0200)]
kvm: x86: SVM: remove unused defines

Remove some unused #defines from svm.c

Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-7-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: SVM: move tsc ratio definitions to svm.h
Maxim Levitsky [Tue, 22 Mar 2022 17:24:46 +0000 (19:24 +0200)]
KVM: x86: SVM: move tsc ratio definitions to svm.h

Another piece of SVM spec which should be in the header file

Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-6-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: SVM: fix avic spec based definitions again
Maxim Levitsky [Tue, 22 Mar 2022 17:24:45 +0000 (19:24 +0200)]
KVM: x86: SVM: fix avic spec based definitions again

Due to wrong rebase, commit
4a204f7895878 ("KVM: SVM: Allow AVIC support on system w/ physical APIC ID > 255")

moved avic spec #defines back to avic.c.

Move them back, and while at it extend AVIC_DOORBELL_PHYSICAL_ID_MASK to 12
bits as well (it will be used in nested avic)

Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20220322172449.235575-5-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: MIPS: remove reference to trap&emulate virtualization
Paolo Bonzini [Sun, 13 Mar 2022 14:05:22 +0000 (15:05 +0100)]
KVM: MIPS: remove reference to trap&emulate virtualization

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220313140522.1307751-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: document limitations of MSR filtering
Paolo Bonzini [Tue, 15 Mar 2022 22:17:15 +0000 (18:17 -0400)]
KVM: x86: document limitations of MSR filtering

MSR filtering requires an exit to userspace that is hard to implement and
would be very slow in the case of nested VMX vmexit and vmentry MSR
accesses.  Document the limitation.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr
Hou Wenlong [Mon, 7 Mar 2022 12:26:33 +0000 (20:26 +0800)]
KVM: x86: Only do MSR filtering when access MSR by rdmsr/wrmsr

If MSR access is rejected by MSR filtering,
kvm_set_msr()/kvm_get_msr() would return KVM_MSR_RET_FILTERED,
and the return value is only handled well for rdmsr/wrmsr.
However, some instruction emulation and state transition also
use kvm_set_msr()/kvm_get_msr() to do msr access but may trigger
some unexpected results if MSR access is rejected, E.g. RDPID
emulation would inject a #UD but RDPID wouldn't cause a exit
when RDPID is supported in hardware and ENABLE_RDTSCP is set.
And it would also cause failure when load MSR at nested entry/exit.
Since msr filtering is based on MSR bitmap, it is better to only
do MSR filtering for rdmsr/wrmsr.

Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <2b2774154f7532c96a6f04d71c82a8bec7d9e80b.1646655860.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86/emulator: Emulate RDPID only if it is enabled in guest
Hou Wenlong [Wed, 2 Mar 2022 13:15:14 +0000 (21:15 +0800)]
KVM: x86/emulator: Emulate RDPID only if it is enabled in guest

When RDTSCP is supported but RDPID is not supported in host,
RDPID emulation is available. However, __kvm_get_msr() would
only fail when RDTSCP/RDPID both are disabled in guest, so
the emulator wouldn't inject a #UD when RDPID is disabled but
RDTSCP is enabled in guest.

Fixes: fb6d4d340e05 ("KVM: x86: emulate RDPID")
Signed-off-by: Hou Wenlong <houwenlong.hwl@antgroup.com>
Message-Id: <1dfd46ae5b76d3ed87bde3154d51c64ea64c99c1.1646226788.git.houwenlong.hwl@antgroup.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86/pmu: Fix and isolate TSX-specific performance event logic
Like Xu [Wed, 9 Mar 2022 08:42:57 +0000 (16:42 +0800)]
KVM: x86/pmu: Fix and isolate TSX-specific performance event logic

HSW_IN_TX* bits are used in generic code which are not supported on
AMD. Worse, these bits overlap with AMD EventSelect[11:8] and hence
using HSW_IN_TX* bits unconditionally in generic code is resulting in
unintentional pmu behavior on AMD. For example, if EventSelect[11:8]
is 0x2, pmc_reprogram_counter() wrongly assumes that
HSW_IN_TX_CHECKPOINTED is set and thus forces sampling period to be 0.

Also per the SDM, both bits 32 and 33 "may only be set if the processor
supports HLE or RTM" and for "IN_TXCP (bit 33): this bit may only be set
for IA32_PERFEVTSEL2."

Opportunistically eliminate code redundancy, because if the HSW_IN_TX*
bit is set in pmc->eventsel, it is already set in attr.config.

Reported-by: Ravi Bangoria <ravi.bangoria@amd.com>
Reported-by: Jim Mattson <jmattson@google.com>
Fixes: 103af0a98788 ("perf, kvm: Support the in_tx/in_tx_cp modifiers in KVM arch perfmon emulation v5")
Co-developed-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@amd.com>
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20220309084257.88931-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set
Maxim Levitsky [Wed, 2 Mar 2022 10:24:57 +0000 (12:24 +0200)]
KVM: x86: mmu: trace kvm_mmu_set_spte after the new SPTE was set

It makes more sense to print new SPTE value than the
old value.

Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220302102457.588450-1-mlevitsk@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs
Jim Mattson [Sat, 26 Feb 2022 23:41:31 +0000 (15:41 -0800)]
KVM: x86/svm: Clear reserved bits written to PerfEvtSeln MSRs

AMD EPYC CPUs never raise a #GP for a WRMSR to a PerfEvtSeln MSR. Some
reserved bits are cleared, and some are not. Specifically, on
Zen3/Milan, bits 19 and 42 are not cleared.

When emulating such a WRMSR, KVM should not synthesize a #GP,
regardless of which bits are set. However, undocumented bits should
not be passed through to the hardware MSR. So, rather than checking
for reserved bits and synthesizing a #GP, just clear the reserved
bits.

This may seem pedantic, but since KVM currently does not support the
"Host/Guest Only" bits (41:40), it is necessary to clear these bits
rather than synthesizing #GP, because some popular guests (e.g Linux)
will set the "Host Only" bit even on CPUs that don't support
EFER.SVME, and they don't expect a #GP.

For example,

root@Ubuntu1804:~# perf stat -e r26 -a sleep 1

 Performance counter stats for 'system wide':

                 0      r26

       1.001070977 seconds time elapsed

Feb 23 03:59:58 Ubuntu1804 kernel: [  405.379957] unchecked MSR access error: WRMSR to 0xc0010200 (tried to write 0x0000020000130026) at rIP: 0xffffffff9b276a28 (native_write_msr+0x8/0x30)
Feb 23 03:59:58 Ubuntu1804 kernel: [  405.379958] Call Trace:
Feb 23 03:59:58 Ubuntu1804 kernel: [  405.379963]  amd_pmu_disable_event+0x27/0x90

Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Reported-by: Lotus Fenn <lotusf@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Like Xu <likexu@tencent.com>
Reviewed-by: David Dunn <daviddunn@google.com>
Message-Id: <20220226234131.2167175-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: Trace all APICv inhibit changes and capture overall status
Sean Christopherson [Fri, 11 Mar 2022 04:35:17 +0000 (04:35 +0000)]
KVM: x86: Trace all APICv inhibit changes and capture overall status

Trace all APICv inhibit changes instead of just those that result in
APICv being (un)inhibited, and log the current state.  Debugging why
APICv isn't working is frustrating as it's hard to see why APICv is still
inhibited, and logging only the first inhibition means unnecessary onion
peeling.

Opportunistically drop the export of the tracepoint, it is not and should
not be used by vendor code due to the need to serialize toggling via
apicv_update_lock.

Note, using the common flow means kvm_apicv_init() switched from atomic
to non-atomic bitwise operations.  The VM is unreachable at init, so
non-atomic is perfectly ok.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: Add wrappers for setting/clearing APICv inhibits
Sean Christopherson [Fri, 11 Mar 2022 04:35:16 +0000 (04:35 +0000)]
KVM: x86: Add wrappers for setting/clearing APICv inhibits

Add set/clear wrappers for toggling APICv inhibits to make the call sites
more readable, and opportunistically rename the inner helpers to align
with the new wrappers and to make them more readable as well.  Invert the
flag from "activate" to "set"; activate is painfully ambiguous as it's
not obvious if the inhibit is being activated, or if APICv is being
activated, in which case the inhibit is being deactivated.

For the functions that take @set, swap the order of the inhibit reason
and @set so that the call sites are visually similar to those that bounce
through the wrapper.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86: Make APICv inhibit reasons an enum and cleanup naming
Sean Christopherson [Fri, 11 Mar 2022 04:35:15 +0000 (04:35 +0000)]
KVM: x86: Make APICv inhibit reasons an enum and cleanup naming

Use an enum for the APICv inhibit reasons, there is no meaning behind
their values and they most definitely are not "unsigned longs".  Rename
the various params to "reason" for consistency and clarity (inhibit may
be confused as a command, i.e. inhibit APICv, instead of the reason that
is getting toggled/checked).

No functional change intended.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220311043517.17027-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: X86: Handle implicit supervisor access with SMAP
Lai Jiangshan [Fri, 11 Mar 2022 07:03:44 +0000 (15:03 +0800)]
KVM: X86: Handle implicit supervisor access with SMAP

There are two kinds of implicit supervisor access
implicit supervisor access when CPL = 3
implicit supervisor access when CPL < 3

Current permission_fault() handles only the first kind for SMAP.

But if the access is implicit when SMAP is on, data may not be read
nor write from any user-mode address regardless the current CPL.

So the second kind should be also supported.

The first kind can be detect via CPL and access mode: if it is
supervisor access and CPL = 3, it must be implicit supervisor access.

But it is not possible to detect the second kind without extra
information, so this patch adds an artificial PFERR_EXPLICIT_ACCESS
into @access. This extra information also works for the first kind, so
the logic is changed to use this information for both cases.

The value of PFERR_EXPLICIT_ACCESS is deliberately chosen to be bit 48
which is in the most significant 16 bits of u64 and less likely to be
forced to change due to future hardware uses it.

This patch removes the call to ->get_cpl() for access mode is determined
by @access.  Not only does it reduce a function call, but also remove
confusions when the permission is checked for nested TDP.  The nested
TDP shouldn't have SMAP checking nor even the L2's CPL have any bearing
on it.  The original code works just because it is always user walk for
NPT and SMAP fault is not set for EPT in update_permission_bitmask.

Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-5-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: X86: Rename variable smap to not_smap in permission_fault()
Lai Jiangshan [Fri, 11 Mar 2022 07:03:43 +0000 (15:03 +0800)]
KVM: X86: Rename variable smap to not_smap in permission_fault()

Comments above the variable says the bit is set when SMAP is overridden
or the same meaning in update_permission_bitmask(): it is not subjected
to SMAP restriction.

Renaming it to reflect the negative implication and make the code better
readability.

Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-4-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: X86: Fix comments in update_permission_bitmask
Lai Jiangshan [Fri, 11 Mar 2022 07:03:42 +0000 (15:03 +0800)]
KVM: X86: Fix comments in update_permission_bitmask

The commit 09f037aa48f3 ("KVM: MMU: speedup update_permission_bitmask")
refactored the code of update_permission_bitmask() and change the
comments.  It added a condition into a list to match the new code,
so the number/order for conditions in the comments should be updated
too.

Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-3-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: X86: Change the type of access u32 to u64
Lai Jiangshan [Fri, 11 Mar 2022 07:03:41 +0000 (15:03 +0800)]
KVM: X86: Change the type of access u32 to u64

Change the type of access u32 to u64 for FNAME(walk_addr) and
->gva_to_gpa().

The kinds of accesses are usually combinations of UWX, and VMX/SVM's
nested paging adds a new factor of access: is it an access for a guest
page table or for a final guest physical address.

And SMAP relies a factor for supervisor access: explicit or implicit.

So @access in FNAME(walk_addr) and ->gva_to_gpa() is better to include
all these information to do the walk.

Although @access(u32) has enough bits to encode all the kinds, this
patch extends it to u64:
o Extra bits will be in the higher 32 bits, so that we can
  easily obtain the traditional access mode (UWX) by converting
  it to u32.
o Reuse the value for the access kind defined by SVM's nested
  paging (PFERR_GUEST_FINAL_MASK and PFERR_GUEST_PAGE_MASK) as
  @error_code in kvm_handle_page_fault().

Signed-off-by: Lai Jiangshan <jiangshan.ljs@antgroup.com>
Message-Id: <20220311070346.45023-2-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: Remove dirty handling from gfn_to_pfn_cache completely
David Woodhouse [Thu, 3 Mar 2022 15:41:12 +0000 (15:41 +0000)]
KVM: Remove dirty handling from gfn_to_pfn_cache completely

It isn't OK to cache the dirty status of a page in internal structures
for an indefinite period of time.

Any time a vCPU exits the run loop to userspace might be its last; the
VMM might do its final check of the dirty log, flush the last remaining
dirty pages to the destination and complete a live migration. If we
have internal 'dirty' state which doesn't get flushed until the vCPU
is finally destroyed on the source after migration is complete, then
we have lost data because that will escape the final copy.

This problem already exists with the use of kvm_vcpu_unmap() to mark
pages dirty in e.g. VMX nesting.

Note that the actual Linux MM already considers the page to be dirty
since we have a writeable mapping of it. This is just about the KVM
dirty logging.

For the nesting-style use cases (KVM_GUEST_USES_PFN) we will need to
track which gfn_to_pfn_caches have been used and explicitly mark the
corresponding pages dirty before returning to userspace. But we would
have needed external tracking of that anyway, rather than walking the
full list of GPCs to find those belonging to this vCPU which are dirty.

So let's rely *solely* on that external tracking, and keep it simple
rather than laying a tempting trap for callers to fall into.

Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220303154127.202856-3-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: Use enum to track if cached PFN will be used in guest and/or host
Sean Christopherson [Thu, 3 Mar 2022 15:41:11 +0000 (15:41 +0000)]
KVM: Use enum to track if cached PFN will be used in guest and/or host

Replace the guest_uses_pa and kernel_map booleans in the PFN cache code
with a unified enum/bitmask. Using explicit names makes it easier to
review and audit call sites.

Opportunistically add a WARN to prevent passing garbage; instantating a
cache without declaring its usage is either buggy or pointless.

Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220303154127.202856-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: SVM: Fix kvm_cache_regs.h inclusions for is_guest_mode()
Peter Gonda [Fri, 4 Mar 2022 16:10:32 +0000 (08:10 -0800)]
KVM: SVM: Fix kvm_cache_regs.h inclusions for is_guest_mode()

Include kvm_cache_regs.h to pick up the definition of is_guest_mode(),
which is referenced by nested_svm_virtualize_tpr() in svm.h. Remove
include from svm_onhpyerv.c which was done only because of lack of
include in svm.h.

Fixes: 883b0a91f41ab ("KVM: SVM: Move Nested SVM Implementation to nested.c")
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: kvm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Gonda <pgonda@google.com>
Message-Id: <20220304161032.2270688-1-pgonda@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86/pmu: Use different raw event masks for AMD and Intel
Jim Mattson [Tue, 8 Mar 2022 01:24:52 +0000 (17:24 -0800)]
KVM: x86/pmu: Use different raw event masks for AMD and Intel

The third nybble of AMD's event select overlaps with Intel's IN_TX and
IN_TXCP bits. Therefore, we can't use AMD64_RAW_EVENT_MASK on Intel
platforms that support TSX.

Declare a raw_event_mask in the kvm_pmu structure, initialize it in
the vendor-specific pmu_refresh() functions, and use that mask for
PERF_TYPE_RAW configurations in reprogram_gp_counter().

Fixes: 710c47651431 ("KVM: x86/pmu: Use AMD64_RAW_EVENT_MASK for PERF_TYPE_RAW")
Signed-off-by: Jim Mattson <jmattson@google.com>
Message-Id: <20220308012452.3468611-1-jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: Don't actually set a request when evicting vCPUs for GFN cache invd
Sean Christopherson [Wed, 23 Feb 2022 16:53:02 +0000 (16:53 +0000)]
KVM: Don't actually set a request when evicting vCPUs for GFN cache invd

Don't actually set a request bit in vcpu->requests when making a request
purely to force a vCPU to exit the guest.  Logging a request but not
actually consuming it would cause the vCPU to get stuck in an infinite
loop during KVM_RUN because KVM would see the pending request and bail
from VM-Enter to service the request.

Note, it's currently impossible for KVM to set KVM_REQ_GPC_INVALIDATE as
nothing in KVM is wired up to set guest_uses_pa=true.  But, it'd be all
too easy for arch code to introduce use of kvm_gfn_to_pfn_cache_init()
without implementing handling of the request, especially since getting
test coverage of MMU notifier interaction with specific KVM features
usually requires a directed test.

Opportunistically rename gfn_to_pfn_cache_invalidate_start()'s wake_vcpus
to evict_vcpus.  The purpose of the request is to get vCPUs out of guest
mode, it's supposed to _avoid_ waking vCPUs that are blocking.

Opportunistically rename KVM_REQ_GPC_INVALIDATE to be more specific as to
what it wants to accomplish, and to genericize the name so that it can
used for similar but unrelated scenarios, should they arise in the future.
Add a comment and documentation to explain why the "no action" request
exists.

Add compile-time assertions to help detect improper usage.  Use the inner
assertless helper in the one s390 path that makes requests without a
hardcoded request.

Cc: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220223165302.3205276-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: avoid double put_page with gfn-to-pfn cache
David Woodhouse [Tue, 29 Mar 2022 17:11:47 +0000 (13:11 -0400)]
KVM: avoid double put_page with gfn-to-pfn cache

If the cache's user host virtual address becomes invalid, there
is still a path from kvm_gfn_to_pfn_cache_refresh() where __release_gpc()
could release the pfn but the gpc->pfn field has not been overwritten
with an error value.  If this happens, kvm_gfn_to_pfn_cache_unmap will
call put_page again on the same page.

Cc: stable@vger.kernel.org
Fixes: 982ed0de4753 ("KVM: Reinstate gfn_to_pfn_cache with invalidation support")
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: x86/mmu: Zap only TDP MMU leafs in zap range and mmu_notifier unmap
Sean Christopherson [Fri, 25 Mar 2022 23:03:48 +0000 (23:03 +0000)]
KVM: x86/mmu: Zap only TDP MMU leafs in zap range and mmu_notifier unmap

Re-introduce zapping only leaf SPTEs in kvm_zap_gfn_range() and
kvm_tdp_mmu_unmap_gfn_range(), this time without losing a pending TLB
flush when processing multiple roots (including nested TDP shadow roots).
Dropping the TLB flush resulted in random crashes when running Hyper-V
Server 2019 in a guest with KSM enabled in the host (or any source of
mmu_notifier invalidations, KSM is just the easiest to force).

This effectively revert commits 873dd122172f8cce329113cfb0dfe3d2344d80c0
and fcb93eb6d09dd302cbef22bd95a5858af75e4156, and thus restores commit
cf3e26427c08ad9015956293ab389004ac6a338e, plus this delta on top:

bool kvm_tdp_mmu_zap_leafs(struct kvm *kvm, int as_id, gfn_t start, gfn_t end,
        struct kvm_mmu_page *root;

        for_each_tdp_mmu_root_yield_safe(kvm, root, as_id)
-               flush = tdp_mmu_zap_leafs(kvm, root, start, end, can_yield, false);
+               flush = tdp_mmu_zap_leafs(kvm, root, start, end, can_yield, flush);

        return flush;
 }

Cc: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Tested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20220325230348.2587437-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: SVM: fix panic on out-of-bounds guest IRQ
Yi Wang [Wed, 9 Mar 2022 11:30:25 +0000 (19:30 +0800)]
KVM: SVM: fix panic on out-of-bounds guest IRQ

As guest_irq is coming from KVM_IRQFD API call, it may trigger
crash in svm_update_pi_irte() due to out-of-bounds:

crash> bt
PID: 22218  TASK: ffff951a6ad74980  CPU: 73  COMMAND: "vcpu8"
 #0 [ffffb1ba6707fa40] machine_kexec at ffffffff8565b397
 #1 [ffffb1ba6707fa90] __crash_kexec at ffffffff85788a6d
 #2 [ffffb1ba6707fb58] crash_kexec at ffffffff8578995d
 #3 [ffffb1ba6707fb70] oops_end at ffffffff85623c0d
 #4 [ffffb1ba6707fb90] no_context at ffffffff856692c9
 #5 [ffffb1ba6707fbf8] exc_page_fault at ffffffff85f95b51
 #6 [ffffb1ba6707fc50] asm_exc_page_fault at ffffffff86000ace
    [exception RIP: svm_update_pi_irte+227]
    RIP: ffffffffc0761b53  RSP: ffffb1ba6707fd08  RFLAGS: 00010086
    RAX: ffffb1ba6707fd78  RBX: ffffb1ba66d91000  RCX: 0000000000000001
    RDX: 00003c803f63f1c0  RSI: 000000000000019a  RDI: ffffb1ba66db2ab8
    RBP: 000000000000019a   R8: 0000000000000040   R9: ffff94ca41b82200
    R10: ffffffffffffffcf  R11: 0000000000000001  R12: 0000000000000001
    R13: 0000000000000001  R14: ffffffffffffffcf  R15: 000000000000005f
    ORIG_RAX: ffffffffffffffff  CS: 0010  SS: 0018
 #7 [ffffb1ba6707fdb8] kvm_irq_routing_update at ffffffffc09f19a1 [kvm]
 #8 [ffffb1ba6707fde0] kvm_set_irq_routing at ffffffffc09f2133 [kvm]
 #9 [ffffb1ba6707fe18] kvm_vm_ioctl at ffffffffc09ef544 [kvm]
    RIP: 00007f143c36488b  RSP: 00007f143a4e04b8  RFLAGS: 00000246
    RAX: ffffffffffffffda  RBX: 00007f05780041d0  RCX: 00007f143c36488b
    RDX: 00007f05780041d0  RSI: 000000004008ae6a  RDI: 0000000000000020
    RBP: 00000000000004e8   R8: 0000000000000008   R9: 00007f05780041e0
    R10: 00007f0578004560  R11: 0000000000000246  R12: 00000000000004e0
    R13: 000000000000001a  R14: 00007f1424001c60  R15: 00007f0578003bc0
    ORIG_RAX: 0000000000000010  CS: 0033  SS: 002b

Vmx have been fix this in commit 3a8b0677fc61 (KVM: VMX: Do not BUG() on
out-of-bounds guest IRQ), so we can just copy source from that to fix
this.

Co-developed-by: Yi Liu <liu.yi24@zte.com.cn>
Signed-off-by: Yi Liu <liu.yi24@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Message-Id: <20220309113025.44469-1-wang.yi59@zte.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoKVM: MMU: propagate alloc_workqueue failure
Paolo Bonzini [Fri, 25 Mar 2022 16:42:52 +0000 (12:42 -0400)]
KVM: MMU: propagate alloc_workqueue failure

If kvm->arch.tdp_mmu_zap_wq cannot be created, the failure has
to be propagated up to kvm_mmu_init_vm and kvm_arch_init_vm.
kvm_arch_init_vm also has to undo all the initialization, so
group all the MMU initialization code at the beginning and
handle cleaning up of kvm_page_track_init.

Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2 years agoMerge branch 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Linus Torvalds [Sat, 2 Apr 2022 02:57:03 +0000 (19:57 -0700)]
Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs

Pull vfs updates from Al Viro:
 "Assorted bits and pieces"

* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  aio: drop needless assignment in aio_read()
  clean overflow checks in count_mounts() a bit
  seq_file: fix NULL pointer arithmetic warning
  uml/x86: use x86 load_unaligned_zeropad()
  asm/user.h: killed unused macros
  constify struct path argument of finish_automount()/do_add_mount()
  fs: Remove FIXME comment in generic_write_checks()