Madalin Bucur [Mon, 16 Mar 2020 12:05:58 +0000 (14:05 +0200)]
arm64: dts: ls1046ardb: set RGMII interfaces to RGMII_ID mode
The correct setting for the RGMII ports on LS1046ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit
1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1046ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii".
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: 3fa395d2c48a ("arm64: dts: add LS1046A DPAA FMan nodes")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Mon, 16 Mar 2020 12:05:57 +0000 (14:05 +0200)]
arm64: dts: ls1043a-rdb: correct RGMII delay mode to rgmii-id
The correct setting for the RGMII ports on LS1043ARDB is to
enable delay on both Rx and Tx so the interface mode used must
be PHY_INTERFACE_MODE_RGMII_ID.
Since commit
1b3047b5208a80 ("net: phy: realtek: add support for
configuring the RX delay on RTL8211F") the Realtek 8211F PHY driver
has control over the RGMII RX delay and it is disabling it for
RGMII_TXID. The LS1043ARDB uses two such PHYs in RGMII_ID mode but
in the device tree the mode was described as "rgmii_txid".
This issue was not apparent at the time as the PHY driver took the
same action for RGMII_TXID and RGMII_ID back then but it became
visible (RX no longer working) after the above patch.
Changing the phy-connection-type to "rgmii-id" to address the issue.
Fixes: bf02f2ffe59c ("arm64: dts: add LS1043A DPAA FMan support")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin Bucur [Mon, 16 Mar 2020 12:05:56 +0000 (14:05 +0200)]
net: fsl/fman: treat all RGMII modes in memac_adjust_link()
Treat all internal delay variants the same as RGMII.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Mar 2020 09:04:24 +0000 (02:04 -0700)]
Merge branch 'ethtool-fail-with-error-if-request-has-unknown-flags'
Michal Kubecek says:
====================
ethtool: fail with error if request has unknown flags
Jakub Kicinski pointed out that if unrecognized flags are set in netlink
header request, kernel shoud fail with an error rather than silently
ignore them so that we have more freedom in future flags semantics.
To help userspace with handling such errors, inform the client which
flags are supported by kernel. For that purpose, we need to allow
passing cookies as part of extack also in case of error (they can be
only passed on success now).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Sun, 15 Mar 2020 17:17:53 +0000 (18:17 +0100)]
ethtool: reject unrecognized request flags
As pointed out by Jakub Kicinski, we ethtool netlink code should respond
with an error if request head has flags set which are not recognized by
kernel, either as a mistake or because it expects functionality introduced
in later kernel versions.
To avoid unnecessary roundtrips, use extack cookie to provide the
information about supported request flags.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Sun, 15 Mar 2020 17:17:48 +0000 (18:17 +0100)]
netlink: add nl_set_extack_cookie_u32()
Similar to existing nl_set_extack_cookie_u64(), add new helper
nl_set_extack_cookie_u32() which sets extack cookie to a u32 value.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Sun, 15 Mar 2020 17:17:43 +0000 (18:17 +0100)]
netlink: allow extack cookie also for error messages
Commit
ba0dc5f6e0ba ("netlink: allow sending extended ACK with cookie on
success") introduced a cookie which can be sent to userspace as part of
extended ack message in the form of NLMSGERR_ATTR_COOKIE attribute.
Currently the cookie is ignored if error code is non-zero but there is
no technical reason for such limitation and it can be useful to provide
machine parseable information as part of an error message.
Include NLMSGERR_ATTR_COOKIE whenever the cookie has been set,
regardless of error code.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Sat, 14 Mar 2020 05:29:54 +0000 (22:29 -0700)]
net_sched: cls_route: remove the right filter from hashtable
route4_change() allocates a new filter and copies values from
the old one. After the new filter is inserted into the hash
table, the old filter should be removed and freed, as the final
step of the update.
However, the current code mistakenly removes the new one. This
looks apparently wrong to me, and it causes double "free" and
use-after-free too, as reported by syzbot.
Reported-and-tested-by: syzbot+f9b32aaacd60305d9687@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+2f8c233f131943d6056d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+9c2df9fd5e9445b74e01@syzkaller.appspotmail.com
Fixes: 1109c00547fc ("net: sched: RCU cls_route")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Mar 2020 08:46:10 +0000 (01:46 -0700)]
Merge branch 'hsr-fix-several-bugs-in-generic-netlink-callback'
Taehee Yoo says:
====================
hsr: fix several bugs in generic netlink callback
This patchset is to fix several bugs they are related in
generic netlink callback in hsr module.
1. The first patch is to add missing rcu_read_lock() in
hsr_get_node_{list/status}().
The hsr_get_node_{list/status}() are not protected by RTNL because
they are callback functions of generic netlink.
But it calls __dev_get_by_index() without acquiring RTNL.
So, it would use unsafe data.
2. The second patch is to avoid failure of hsr_get_node_list().
hsr_get_node_list() is a callback of generic netlink and
it is used to get node information in userspace.
But, if there are so many nodes, it fails because of buffer size.
So, in this patch, restart routine is added.
3. The third patch is to set .netnsok flag to true.
If .netnsok flag is false, non-init_net namespace is not allowed to
operate generic netlink operations.
So, currently, non-init_net namespace has no way to get node information
because .netnsok is false in the current hsr code.
Change log:
v1->v2:
- Preserve reverse christmas tree variable ordering in the second patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Fri, 13 Mar 2020 06:50:33 +0000 (06:50 +0000)]
hsr: set .netnsok flag
The hsr module has been supporting the list and status command.
(HSR_C_GET_NODE_LIST and HSR_C_GET_NODE_STATUS)
These commands send node information to the user-space via generic netlink.
But, in the non-init_net namespace, these commands are not allowed
because .netnsok flag is false.
So, there is no way to get node information in the non-init_net namespace.
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Fri, 13 Mar 2020 06:50:24 +0000 (06:50 +0000)]
hsr: add restart routine into hsr_get_node_list()
The hsr_get_node_list() is to send node addresses to the userspace.
If there are so many nodes, it could fail because of buffer size.
In order to avoid this failure, the restart routine is added.
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taehee Yoo [Fri, 13 Mar 2020 06:50:14 +0000 (06:50 +0000)]
hsr: use rcu_read_lock() in hsr_get_node_{list/status}()
hsr_get_node_{list/status}() are not under rtnl_lock() because
they are callback functions of generic netlink.
But they use __dev_get_by_index() without rtnl_lock().
So, it would use unsafe data.
In order to fix it, rcu_read_lock() and dev_get_by_index_rcu()
are used instead of __dev_get_by_index().
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 16 Mar 2020 00:06:22 +0000 (17:06 -0700)]
Merge branch 'net-Use-scnprintf-for-avoiding-potential-buffer-overflow'
Takashi Iwai says:
====================
net: Use scnprintf() for avoiding potential buffer overflow
here is a respin of trivial patch series just to convert suspicious
snprintf() usages with the more safer one, scnprintf().
v1->v2: Align the remaining lines to the open parenthesis
Excluded i40e patch that was already queued
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sun, 15 Mar 2020 09:35:03 +0000 (10:35 +0100)]
net: netdevsim: Use scnprintf() for avoiding potential buffer overflow
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sun, 15 Mar 2020 09:35:02 +0000 (10:35 +0100)]
net: sfc: Use scnprintf() for avoiding potential buffer overflow
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Martin Habets <mhabets@solarflare.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sun, 15 Mar 2020 09:35:01 +0000 (10:35 +0100)]
net: ionic: Use scnprintf() for avoiding potential buffer overflow
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sun, 15 Mar 2020 09:35:00 +0000 (10:35 +0100)]
net: nfp: Use scnprintf() for avoiding potential buffer overflow
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: oss-drivers@netronome.com
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sun, 15 Mar 2020 09:34:59 +0000 (10:34 +0100)]
net: mlx4: Use scnprintf() for avoiding potential buffer overflow
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: Tariq Toukan <tariqt@mellanox.com>
To: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Sun, 15 Mar 2020 09:34:58 +0000 (10:34 +0100)]
net: caif: Use scnprintf() for avoiding potential buffer overflow
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: "David S . Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 15 Mar 2020 08:07:35 +0000 (10:07 +0200)]
mlxsw: reg: Increase register field length to 31 bits
The cited commit set a value of 2^31-1 in order to "disable" the shaper
on a given a port. However, the length of the maximum shaper rate field
was not updated from 28 bits to 31 bits, which means ports are still
limited to ~268Gbps despite supporting speeds of 400Gbps.
Fix this by increasing the field's length.
Fixes: 92afbfedb77d ("mlxsw: reg: Increase MLXSW_REG_QEEC_MAS_DIS")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Westphal [Sat, 14 Mar 2020 07:18:42 +0000 (08:18 +0100)]
geneve: move debug check after netdev unregister
The debug check must be done after unregister_netdevice_many() call --
the list_del() for this is done inside .ndo_stop.
Fixes: 2843a25348f8 ("geneve: speedup geneve tunnels dismantle")
Reported-and-tested-by: <syzbot+68a8ed58e3d17c700de5@syzkaller.appspotmail.com>
Cc: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 13 Mar 2020 16:18:09 +0000 (12:18 -0400)]
net/packet: tpacket_rcv: avoid a producer race condition
PACKET_RX_RING can cause multiple writers to access the same slot if a
fast writer wraps the ring while a slow writer is still copying. This
is particularly likely with few, large, slots (e.g., GSO packets).
Synchronize kernel thread ownership of rx ring slots with a bitmap.
Writers acquire a slot race-free by testing tp_status TP_STATUS_KERNEL
while holding the sk receive queue lock. They release this lock before
copying and set tp_status to TP_STATUS_USER to release to userspace
when done. During copying, another writer may take the lock, also see
TP_STATUS_KERNEL, and start writing to the same slot.
Introduce a new rx_owner_map bitmap with a bit per slot. To acquire a
slot, test and set with the lock held. To release race-free, update
tp_status and owner bit as a transaction, so take the lock again.
This is the one of a variety of discussed options (see Link below):
* instead of a shadow ring, embed the data in the slot itself, such as
in tp_padding. But any test for this field may match a value left by
userspace, causing deadlock.
* avoid the lock on release. This leaves a small race if releasing the
shadow slot before setting TP_STATUS_USER. The below reproducer showed
that this race is not academic. If releasing the slot after tp_status,
the race is more subtle. See the first link for details.
* add a new tp_status TP_KERNEL_OWNED to avoid the transactional store
of two fields. But, legacy applications may interpret all non-zero
tp_status as owned by the user. As libpcap does. So this is possible
only opt-in by newer processes. It can be added as an optional mode.
* embed the struct at the tail of pg_vec to avoid extra allocation.
The implementation proved no less complex than a separate field.
The additional locking cost on release adds contention, no different
than scaling on multicore or multiqueue h/w. In practice, below
reproducer nor small packet tcpdump showed a noticeable change in
perf report in cycles spent in spinlock. Where contention is
problematic, packet sockets support mitigation through PACKET_FANOUT.
And we can consider adding opt-in state TP_KERNEL_OWNED.
Easy to reproduce by running multiple netperf or similar TCP_STREAM
flows concurrently with `tcpdump -B 129 -n greater 60000`.
Based on an earlier patchset by Jon Rosen. See links below.
I believe this issue goes back to the introduction of tpacket_rcv,
which predates git history.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg237222.html
Suggested-by: Jon Rosen <jrosen@cisco.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jon Rosen <jrosen@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata [Fri, 13 Mar 2020 11:39:36 +0000 (13:39 +0200)]
net: ip_gre: Separate ERSPAN newlink / changelink callbacks
ERSPAN shares most of the code path with GRE and gretap code. While that
helps keep the code compact, it is also error prone. Currently a broken
userspace can turn a gretap tunnel into a de facto ERSPAN one by passing
IFLA_GRE_ERSPAN_VER. There has been a similar issue in ip6gretap in the
past.
To prevent these problems in future, split the newlink and changelink code
paths. Split the ERSPAN code out of ipgre_netlink_parms() into a new
function erspan_netlink_parms(). Extract a piece of common logic from
ipgre_newlink() and ipgre_changelink() into ipgre_newlink_encap_setup().
Add erspan_newlink() and erspan_changelink().
Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shahjada Abul Husain [Fri, 13 Mar 2020 09:02:57 +0000 (14:32 +0530)]
cxgb4: fix delete filter entry fail in unload path
Currently, the hardware TID index is assumed to start from index 0.
However, with the following changeset,
commit
c21939998802 ("cxgb4: add support for high priority filters")
hardware TID index can start after the high priority region, which
has introduced a regression resulting in remove filters entry
failure for cxgb4 unload path. This patch fix that.
Fixes: c21939998802 ("cxgb4: add support for high priority filters")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Markus Fuchs [Fri, 6 Mar 2020 16:38:48 +0000 (17:38 +0100)]
net: stmmac: platform: Fix misleading interrupt error msg
Not every stmmac based platform makes use of the eth_wake_irq or eth_lpi
interrupts. Use the platform_get_irq_byname_optional variant for these
interrupts, so no error message is displayed, if they can't be found.
Rather print an information to hint something might be wrong to assist
debugging on platforms which use these interrupts.
Signed-off-by: Markus Fuchs <mklntf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bruno Meneguele [Thu, 12 Mar 2020 23:08:20 +0000 (20:08 -0300)]
net/bpfilter: fix dprintf usage for /dev/kmsg
The bpfilter UMH code was recently changed to log its informative messages to
/dev/kmsg, however this interface doesn't support SEEK_CUR yet, used by
dprintf(). As result dprintf() returns -EINVAL and doesn't log anything.
However there already had some discussions about supporting SEEK_CUR into
/dev/kmsg interface in the past it wasn't concluded. Since the only user of
that from userspace perspective inside the kernel is the bpfilter UMH
(userspace) module it's better to correct it here instead waiting a conclusion
on the interface.
Fixes: 36c4357c63f3 ("net: bpfilter: print umh messages to /dev/kmsg")
Signed-off-by: Bruno Meneguele <bmeneg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 12 Mar 2020 05:42:28 +0000 (22:42 -0700)]
net_sched: keep alloc_hash updated after hash allocation
In commit
599be01ee567 ("net_sched: fix an OOB access in cls_tcindex")
I moved cp->hash calculation before the first
tcindex_alloc_perfect_hash(), but cp->alloc_hash is left untouched.
This difference could lead to another out of bound access.
cp->alloc_hash should always be the size allocated, we should
update it after this tcindex_alloc_perfect_hash().
Reported-and-tested-by: syzbot+dcc34d54d68ef7d2d53d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+c72da7b9ed57cde6fca2@syzkaller.appspotmail.com
Fixes: 599be01ee567 ("net_sched: fix an OOB access in cls_tcindex")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 12 Mar 2020 05:42:27 +0000 (22:42 -0700)]
net_sched: hold rtnl lock in tcindex_partial_destroy_work()
syzbot reported a use-after-free in tcindex_dump(). This is due to
the lack of RTNL in the deferred rcu work. We queue this work with
RTNL in tcindex_change(), later, tcindex_dump() is called:
fh = tp->ops->get(tp, t->tcm_handle);
...
err = tp->ops->change(..., &fh, ...);
tfilter_notify(..., fh, ...);
but there is nothing to serialize the pending
tcindex_partial_destroy_work() with tcindex_dump().
Fix this by simply holding RTNL in tcindex_partial_destroy_work(),
so that it won't be called until RTNL is released after
tc_new_tfilter() is completed.
Reported-and-tested-by: syzbot+653090db2562495901dc@syzkaller.appspotmail.com
Fixes: 3d210534cc93 ("net_sched: fix a race condition in tcindex_destroy()")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 13 Mar 2020 18:21:25 +0000 (11:21 -0700)]
Merge tag 'wireless-drivers-2020-03-13' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.6
Third, and hopefully last, set of fixes for v5.6.
iwlwifi
* fix a locking issue in time events handling
* a fix in rate-scaling
* fix for a potential NULL pointer deref
* enable antenna diversity in some devices that were erroneously not doing it
* allow FW dumps to continue when the FW is stuck
* a fix in the HE capabilities handling
* another fix for FW dumps where we were reading wrong addresses
* fix link in MAINTAINERS file
rtlwifi
* fix regression causing connect issues in v5.4
wlcore
* remove merge damage which luckily didn't have any impact on functionality
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 13 Mar 2020 18:13:45 +0000 (11:13 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Alexei Starovoitov says:
====================
pull-request: bpf 2020-03-12
The following pull-request contains BPF updates for your *net* tree.
We've added 12 non-merge commits during the last 8 day(s) which contain
a total of 12 files changed, 161 insertions(+), 15 deletions(-).
The main changes are:
1) Andrii fixed two bugs in cgroup-bpf.
2) John fixed sockmap.
3) Luke fixed x32 jit.
4) Martin fixed two issues in struct_ops.
5) Yonghong fixed bpf_send_signal.
6) Yoshiki fixed BTF enum.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 13 Mar 2020 01:05:19 +0000 (18:05 -0700)]
Merge tag 'drm-fixes-2020-03-13' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"It's a bit quieter, probably not as much as it could be.
There is on large regression fix in here from Lyude for displayport
bandwidth calculations, there've been reports of multi-monitor in
docks not working since -rc1 and this has been tested to fix those.
Otherwise it's a bunch of i915 (with some GVT fixes), a set of amdgpu
watermark + bios fixes, and an exynos iommu cleanup fix.
core:
- DP MST bandwidth regression fix.
i915:
- hard lockup fix
- GVT fixes
- 32-bit alignment issue fix
- timeline wait fixes
- cacheline_retire and free
amdgpu:
- Update the display watermark bounding box for navi14
- Fix fetching vbios directly from rom on vega20/arcturus
- Navi and renoir watermark fixes
exynos:
- iommu object cleanup fix"
`
* tag 'drm-fixes-2020-03-13' of git://anongit.freedesktop.org/drm/drm:
drm/dp_mst: Rewrite and fix bandwidth limit checks
drm/dp_mst: Reprobe path resources in CSN handler
drm/dp_mst: Use full_pbn instead of available_pbn for bandwidth checks
drm/dp_mst: Rename drm_dp_mst_is_dp_mst_end_device() to be less redundant
drm/i915: Defer semaphore priority bumping to a workqueue
drm/i915/gt: Close race between cacheline_retire and free
drm/i915/execlists: Enable timeslice on partial virtual engine dequeue
drm/i915: be more solid in checking the alignment
drm/i915/gvt: Fix dma-buf display blur issue on CFL
drm/i915: Return early for await_start on same timeline
drm/i915: Actually emit the await_start
drm/amdgpu/powerplay: nv1x, renior copy dcn clock settings of watermark to smu during boot up
drm/exynos: Fix cleanup of IOMMU related objects
drm/amdgpu: correct ROM_INDEX/DATA offset for VEGA20
drm/amd/display: update soc bb for nv14
drm/i915/gvt: Fix emulated vbt size issue
drm/i915/gvt: Fix unnecessary schedule timer when no vGPU exits
Dave Airlie [Fri, 13 Mar 2020 00:38:24 +0000 (10:38 +1000)]
Merge tag 'topic/mst-bw-check-fixes-for-airlied-2020-03-12-2' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
UAPI Changes: None
Cross-subsystem Changes: None
Core Changes: Fixed regressions introduced by commit
cd82d82cbc04
("drm/dp_mst: Add branch bandwidth validation to MST atomic check"),
which would cause us to:
* Calculate the available bandwidth on an MST topology incorrectly, and
as a result reject most display configurations that would try to enable
more then one sink on a topology
* Occasionally expose MST connectors to userspace before finishing
probing their PBN capabilities, resulting in us rejecting display
configurations because we assumed briefly that no bandwidth was
available
Driver Changes: None
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/bf16ee577567beed91c86b7d9cda3ec2e8c50a71.camel@redhat.com
Dave Airlie [Thu, 12 Mar 2020 23:41:15 +0000 (09:41 +1000)]
Merge tag 'drm-intel-fixes-2020-03-12' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.6-rc6:
- hard lockup fix
- GVT fixes
- 32-bit alignment issue fix
- timeline wait fixes
- cacheline_retire and free
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lfo6ksvw.fsf@intel.com
Dave Airlie [Thu, 12 Mar 2020 23:22:25 +0000 (09:22 +1000)]
Merge tag 'amd-drm-fixes-5.6-2020-03-11' of git://people.freedesktop.org/~agd5f/linux into drm-fixes
amd-drm-fixes-5.6-2020-03-11:
amdgpu:
- Update the display watermark bounding box for navi14
- Fix fetching vbios directly from rom on vega20/arcturus
- Navi and renoir watermark fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200312020924.4161-1-alexander.deucher@amd.com
Linus Torvalds [Thu, 12 Mar 2020 23:19:19 +0000 (16:19 -0700)]
Merge git://git./linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
"It looks like a decent sized set of fixes, but a lot of these are one
liner off-by-one and similar type changes:
1) Fix netlink header pointer to calcular bad attribute offset
reported to user. From Pablo Neira Ayuso.
2) Don't double clear PHY interrupts when ->did_interrupt is set,
from Heiner Kallweit.
3) Add missing validation of various (devlink, nl802154, fib, etc.)
attributes, from Jakub Kicinski.
4) Missing *pos increments in various netfilter seq_next ops, from
Vasily Averin.
5) Missing break in of_mdiobus_register() loop, from Dajun Jin.
6) Don't double bump tx_dropped in veth driver, from Jiang Lidong.
7) Work around FMAN erratum
A050385, from Madalin Bucur.
8) Make sure ARP header is pulled early enough in bonding driver,
from Eric Dumazet.
9) Do a cond_resched() during multicast processing of ipvlan and
macvlan, from Mahesh Bandewar.
10) Don't attach cgroups to unrelated sockets when in interrupt
context, from Shakeel Butt.
11) Fix tpacket ring state management when encountering unknown GSO
types. From Willem de Bruijn.
12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend()
only in the suspend context. From Heiner Kallweit"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits)
net: systemport: fix index check to avoid an array out of bounds access
tc-testing: add ETS scheduler to tdc build configuration
net: phy: fix MDIO bus PM PHY resuming
net: hns3: clear port base VLAN when unload PF
net: hns3: fix RMW issue for VLAN filter switch
net: hns3: fix VF VLAN table entries inconsistent issue
net: hns3: fix "tc qdisc del" failed issue
taprio: Fix sending packets without dequeueing them
net: mvmdio: avoid error message for optional IRQ
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
net: memcg: fix lockdep splat in inet_csk_accept()
s390/qeth: implement smarter resizing of the RX buffer pool
s390/qeth: refactor buffer pool code
s390/qeth: use page pointers to manage RX buffer pool
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
net/packet: tpacket_rcv: do not increment ring index on drop
sxgbe: Fix off by one in samsung driver strncpy size arg
net: caif: Add lockdep expression to RCU traversal primitive
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
...
Lyude Paul [Mon, 9 Mar 2020 21:01:31 +0000 (17:01 -0400)]
drm/dp_mst: Rewrite and fix bandwidth limit checks
Sigh, this is mostly my fault for not giving commit
cd82d82cbc04
("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
enough scrutiny during review. The way we're checking bandwidth
limitations here is mostly wrong:
For starters, drm_dp_mst_atomic_check_bw_limit() determines the
pbn_limit of a branch by simply scanning each port on the current branch
device, then uses the last non-zero full_pbn value that it finds. It
then counts the sum of the PBN used on each branch device for that
level, and compares against the full_pbn value it found before.
This is wrong because ports can and will have different PBN limitations
on many hubs, especially since a number of DisplayPort hubs out there
will be clever and only use the smallest link rate required for each
downstream sink - potentially giving every port a different full_pbn
value depending on what link rate it's trained at. This means with our
current code, which max PBN value we end up with is not well defined.
Additionally, we also need to remember when checking bandwidth
limitations that the top-most device in any MST topology is a branch
device, not a port. This means that the first level of a topology
doesn't technically have a full_pbn value that needs to be checked.
Instead, we should assume that so long as our VCPI allocations fit we're
within the bandwidth limitations of the primary MSTB.
We do however, want to check full_pbn on every port including those of
the primary MSTB. However, it's important to keep in mind that this
value represents the minimum link rate /between a port's sink or mstb,
and the mstb itself/. A quick diagram to explain:
MSTB #1
/ \
/ \
Port #1 Port #2
full_pbn for Port #1 → | | ← full_pbn for Port #2
Sink #1 MSTB #2
|
etc...
Note that in the above diagram, the combined PBN from all VCPI
allocations on said hub should not exceed the full_pbn value of port #2,
and the display configuration on sink #1 should not exceed the full_pbn
value of port #1. However, port #1 and port #2 can otherwise consume as
much bandwidth as they want so long as their VCPI allocations still fit.
And finally - our current bandwidth checking code also makes the mistake
of not checking whether something is an end device or not before trying
to traverse down it.
So, let's fix it by rewriting our bandwidth checking helpers. We split
the function into one part for handling branches which simply adds up
the total PBN on each branch and returns it, and one for checking each
port to ensure we're not going over its PBN limit. Phew.
This should fix regressions seen, where we erroneously reject display
configurations due to thinking they're going over our bandwidth limits
when they're not.
Changes since v1:
* Took an even closer look at how PBN limitations are supposed to be
handled, and did some experimenting with Sean Paul. Ended up rewriting
these helpers again, but this time they should actually be correct!
Changes since v2:
* Small indenting fix
* Fix pbn_used check in drm_dp_mst_atomic_check_port_bw_limit()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc04 ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Sean Paul <seanpaul@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200309210131.1497545-1-lyude@redhat.com
Lyude Paul [Fri, 6 Mar 2020 23:46:21 +0000 (18:46 -0500)]
drm/dp_mst: Reprobe path resources in CSN handler
We used to punt off reprobing path resources to the link address probe
work, but now that we handle CSNs asynchronously from the driver's HPD
handling we can do whatever the heck we want from the CSN!
So, reprobe the path resources from drm_dp_mst_handle_conn_stat(). Also,
get rid of the path resource reprobing code in
drm_dp_check_and_send_link_address() since it's needlessly complicated
when we already reprobe path resources from
drm_dp_handle_link_address_port(). And finally, teach
drm_dp_send_enum_path_resources() to return 1 on PBN changes so we know
if we need to send another hotplug or not.
This fixes issues where we've indicated to userspace that a port has
just been connected, before we actually probed it's available PBN -
something that results in unexpected atomic check failures.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc04 ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-4-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Lyude Paul [Fri, 6 Mar 2020 23:46:20 +0000 (18:46 -0500)]
drm/dp_mst: Use full_pbn instead of available_pbn for bandwidth checks
DisplayPort specifications are fun. For a while, it's been really
unclear to us what available_pbn actually does. There's a somewhat vague
explanation in the DisplayPort spec (starting from 1.2) that partially
explains it:
The minimum payload bandwidth number supported by the path. Each node
updates this number with its available payload bandwidth number if its
payload bandwidth number is less than that in the Message Transaction
reply.
So, it sounds like available_pbn represents the smallest link rate in
use between the source and the branch device. Cool, so full_pbn is just
the highest possible PBN that the branch device supports right?
Well, we assumed that for quite a while until Sean Paul noticed that on
some MST hubs, available_pbn will actually get set to 0 whenever there's
any active payloads on the respective branch device. This caused quite a
bit of confusion since clearing the payload ID table would end up fixing
the available_pbn value.
So, we just went with that until commit
cd82d82cbc04 ("drm/dp_mst: Add
branch bandwidth validation to MST atomic check") started breaking
people's setups due to us getting erroneous available_pbn values. So, we
did some more digging and got confused until we finally looked at the
definition for full_pbn:
The bandwidth of the link at the trained link rate and lane count
between the DP Source device and the DP Sink device with no time slots
allocated to VC Payloads, represented as a Payload Bandwidth Number. As
with the Available_Payload_Bandwidth_Number, this number is determined
by the link with the lowest lane count and link rate.
That's what we get for not reading specs closely enough, hehe. So, since
full_pbn is definitely what we want for doing bandwidth restriction
checks - let's start using that instead and ignore available_pbn
entirely.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: cd82d82cbc04 ("drm/dp_mst: Add branch bandwidth validation to MST atomic check")
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-3-lyude@redhat.com
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Lyude Paul [Fri, 6 Mar 2020 23:46:19 +0000 (18:46 -0500)]
drm/dp_mst: Rename drm_dp_mst_is_dp_mst_end_device() to be less redundant
It's already prefixed by dp_mst, so we don't really need to repeat
ourselves here. One of the changes I should have picked up originally
when reviewing MST DSC support.
There should be no functional changes here
Cc: Mikita Lipski <mikita.lipski@amd.com>
Cc: Sean Paul <seanpaul@google.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306234623.547525-2-lyude@redhat.com
Linus Torvalds [Thu, 12 Mar 2020 22:51:26 +0000 (15:51 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes for old crap in ->atomic_open() instances"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
cifs_atomic_open(): fix double-put on late allocation failure
gfs2_atomic_open(): fix O_EXCL|O_CREAT handling on cold dcache
Colin Ian King [Thu, 12 Mar 2020 15:04:30 +0000 (15:04 +0000)]
net: systemport: fix index check to avoid an array out of bounds access
Currently the bounds check on index is off by one and can lead to
an out of bounds access on array priv->filters_loc when index is
RXCHK_BRCM_TAG_MAX.
Fixes: bb9051a2b230 ("net: systemport: Add support for WAKE_FILTER")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide Caratti [Thu, 12 Mar 2020 16:51:45 +0000 (17:51 +0100)]
tc-testing: add ETS scheduler to tdc build configuration
add CONFIG_NET_SCH_ETS to 'config', otherwise test suites using this file
to perform a full tdc run will encounter the following warning:
ok 645 e90e - Add ETS qdisc using bands # skipped - "-----> teardown stage" did not complete successfully
Fixes: 82c664b69c8b ("selftests: qdiscs: Add test coverage for ETS Qdisc")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 12 Mar 2020 21:25:20 +0000 (22:25 +0100)]
net: phy: fix MDIO bus PM PHY resuming
So far we have the unfortunate situation that mdio_bus_phy_may_suspend()
is called in suspend AND resume path, assuming that function result is
the same. After the original change this is no longer the case,
resulting in broken resume as reported by Geert.
To fix this call mdio_bus_phy_may_suspend() in the suspend path only,
and let the phy_device store the info whether it was suspended by
MDIO bus PM.
Fixes: 503ba7c69610 ("net: phy: Avoid multiple suspends")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Thu, 12 Mar 2020 22:25:20 +0000 (18:25 -0400)]
cifs_atomic_open(): fix double-put on late allocation failure
several iterations of ->atomic_open() calling conventions ago, we
used to need fput() if ->atomic_open() failed at some point after
successful finish_open(). Now (since 2016) it's not needed -
struct file carries enough state to make fput() work regardless
of the point in struct file lifecycle and discarding it on
failure exits in open() got unified. Unfortunately, I'd missed
the fact that we had an instance of ->atomic_open() (cifs one)
that used to need that fput(), as well as the stale comment in
finish_open() demanding such late failure handling. Trivially
fixed...
Fixes: fe9ec8291fca "do_last(): take fput() on error after opening to out:"
Cc: stable@kernel.org # v4.7+
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Tue, 10 Mar 2020 13:31:41 +0000 (09:31 -0400)]
gfs2_atomic_open(): fix O_EXCL|O_CREAT handling on cold dcache
with the way fs/namei.c:do_last() had been done, ->atomic_open()
instances needed to recognize the case when existing file got
found with O_EXCL|O_CREAT, either by falling back to finish_no_open()
or failing themselves. gfs2 one didn't.
Fixes: 6d4ade986f9c (GFS2: Add atomic_open support)
Cc: stable@kernel.org # v3.11
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
David S. Miller [Thu, 12 Mar 2020 18:38:27 +0000 (11:38 -0700)]
Merge branch 'hns3-fixes'
Huazhong Tan says:
====================
net: hns3: fixes for -net
This series includes several bugfixes for the HNS3 ethernet driver.
[patch 1] fixes an "tc qdisc del" failure.
[patch 2] fixes SW & HW VLAN table not consistent issue.
[patch 3] fixes a RMW issue related to VLAN filter switch.
[patch 4] clears port based VLAN when uploading PF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 12 Mar 2020 07:11:06 +0000 (15:11 +0800)]
net: hns3: clear port base VLAN when unload PF
Currently, PF missed to clear the port base VLAN for VF when
unload. In this case, the VLAN id will remain in the VLAN
table. This patch fixes it.
Fixes: 92f11ea177cd ("net: hns3: fix set port based VLAN issue for VF")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 12 Mar 2020 07:11:05 +0000 (15:11 +0800)]
net: hns3: fix RMW issue for VLAN filter switch
According to the user manual, the ingress and egress VLAN filter
are configured at the same time. Currently, hclge_init_vlan_config()
and hclge_set_vlan_spoofchk() will both change the VLAN filter
switch. So it's necessary to read the old configuration before
modifying it.
Fixes: 22044f95faa0 ("net: hns3: add support for spoof check setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 12 Mar 2020 07:11:04 +0000 (15:11 +0800)]
net: hns3: fix VF VLAN table entries inconsistent issue
Currently, if VF is loaded on the host side, the host doesn't
clear the VF's VLAN table entries when VF removing. In this
case, when doing reset and disabling sriov at the same time the
VLAN device over VF will be removed, but the VLAN table entries
in hardware are remained.
This patch fixes it by asking PF to clear the VLAN table entries for
VF when VF is removing. It also clears the VLAN table full bit
after VF VLAN table entries being cleared.
Fixes: c6075b193462 ("net: hns3: Record VF vlan tables")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonglong Liu [Thu, 12 Mar 2020 07:11:03 +0000 (15:11 +0800)]
net: hns3: fix "tc qdisc del" failed issue
The HNS3 driver supports to configure TC numbers and TC to priority
map via "tc" tool. But when delete the rule, will fail, because
the HNS3 driver needs at least one TC, but the "tc" tool sets TC
number to zero when delete.
This patch makes sure that the TC number is at least one.
Fixes: 30d240dfa2e8 ("net: hns3: Add mqprio hardware offload support in hns3 driver")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vinicius Costa Gomes [Mon, 9 Mar 2020 17:39:53 +0000 (10:39 -0700)]
taprio: Fix sending packets without dequeueing them
There was a bug that was causing packets to be sent to the driver
without first calling dequeue() on the "child" qdisc. And the KASAN
report below shows that sending a packet without calling dequeue()
leads to bad results.
The problem is that when checking the last qdisc "child" we do not set
the returned skb to NULL, which can cause it to be sent to the driver,
and so after the skb is sent, it may be freed, and in some situations a
reference to it may still be in the child qdisc, because it was never
dequeued.
The crash log looks like this:
[ 19.937538] ==================================================================
[ 19.938300] BUG: KASAN: use-after-free in taprio_dequeue_soft+0x620/0x780
[ 19.938968] Read of size 4 at addr
ffff8881128628cc by task swapper/1/0
[ 19.939612]
[ 19.939772] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.6.0-rc3+ #97
[ 19.940397] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.0-59-gc9ba5276e321-prebuilt.qe4
[ 19.941523] Call Trace:
[ 19.941774] <IRQ>
[ 19.941985] dump_stack+0x97/0xe0
[ 19.942323] print_address_description.constprop.0+0x3b/0x60
[ 19.942884] ? taprio_dequeue_soft+0x620/0x780
[ 19.943325] ? taprio_dequeue_soft+0x620/0x780
[ 19.943767] __kasan_report.cold+0x1a/0x32
[ 19.944173] ? taprio_dequeue_soft+0x620/0x780
[ 19.944612] kasan_report+0xe/0x20
[ 19.944954] taprio_dequeue_soft+0x620/0x780
[ 19.945380] __qdisc_run+0x164/0x18d0
[ 19.945749] net_tx_action+0x2c4/0x730
[ 19.946124] __do_softirq+0x268/0x7bc
[ 19.946491] irq_exit+0x17d/0x1b0
[ 19.946824] smp_apic_timer_interrupt+0xeb/0x380
[ 19.947280] apic_timer_interrupt+0xf/0x20
[ 19.947687] </IRQ>
[ 19.947912] RIP: 0010:default_idle+0x2d/0x2d0
[ 19.948345] Code: 00 00 41 56 41 55 65 44 8b 2d 3f 8d 7c 7c 41 54 55 53 0f 1f 44 00 00 e8 b1 b2 c5 fd e9 07 00 3
[ 19.950166] RSP: 0018:
ffff88811a3efda0 EFLAGS:
00000282 ORIG_RAX:
ffffffffffffff13
[ 19.950909] RAX:
0000000080000000 RBX:
ffff88811a3a9600 RCX:
ffffffff8385327e
[ 19.951608] RDX:
1ffff110234752c0 RSI:
0000000000000000 RDI:
ffffffff8385262f
[ 19.952309] RBP:
ffffed10234752c0 R08:
0000000000000001 R09:
ffffed10234752c1
[ 19.953009] R10:
ffffed10234752c0 R11:
ffff88811a3a9607 R12:
0000000000000001
[ 19.953709] R13:
0000000000000001 R14:
0000000000000000 R15:
0000000000000000
[ 19.954408] ? default_idle_call+0x2e/0x70
[ 19.954816] ? default_idle+0x1f/0x2d0
[ 19.955192] default_idle_call+0x5e/0x70
[ 19.955584] do_idle+0x3d4/0x500
[ 19.955909] ? arch_cpu_idle_exit+0x40/0x40
[ 19.956325] ? _raw_spin_unlock_irqrestore+0x23/0x30
[ 19.956829] ? trace_hardirqs_on+0x30/0x160
[ 19.957242] cpu_startup_entry+0x19/0x20
[ 19.957633] start_secondary+0x2a6/0x380
[ 19.958026] ? set_cpu_sibling_map+0x18b0/0x18b0
[ 19.958486] secondary_startup_64+0xa4/0xb0
[ 19.958921]
[ 19.959078] Allocated by task 33:
[ 19.959412] save_stack+0x1b/0x80
[ 19.959747] __kasan_kmalloc.constprop.0+0xc2/0xd0
[ 19.960222] kmem_cache_alloc+0xe4/0x230
[ 19.960617] __alloc_skb+0x91/0x510
[ 19.960967] ndisc_alloc_skb+0x133/0x330
[ 19.961358] ndisc_send_ns+0x134/0x810
[ 19.961735] addrconf_dad_work+0xad5/0xf80
[ 19.962144] process_one_work+0x78e/0x13a0
[ 19.962551] worker_thread+0x8f/0xfa0
[ 19.962919] kthread+0x2ba/0x3b0
[ 19.963242] ret_from_fork+0x3a/0x50
[ 19.963596]
[ 19.963753] Freed by task 33:
[ 19.964055] save_stack+0x1b/0x80
[ 19.964386] __kasan_slab_free+0x12f/0x180
[ 19.964830] kmem_cache_free+0x80/0x290
[ 19.965231] ip6_mc_input+0x38a/0x4d0
[ 19.965617] ipv6_rcv+0x1a4/0x1d0
[ 19.965948] __netif_receive_skb_one_core+0xf2/0x180
[ 19.966437] netif_receive_skb+0x8c/0x3c0
[ 19.966846] br_handle_frame_finish+0x779/0x1310
[ 19.967302] br_handle_frame+0x42a/0x830
[ 19.967694] __netif_receive_skb_core+0xf0e/0x2a90
[ 19.968167] __netif_receive_skb_one_core+0x96/0x180
[ 19.968658] process_backlog+0x198/0x650
[ 19.969047] net_rx_action+0x2fa/0xaa0
[ 19.969420] __do_softirq+0x268/0x7bc
[ 19.969785]
[ 19.969940] The buggy address belongs to the object at
ffff888112862840
[ 19.969940] which belongs to the cache skbuff_head_cache of size 224
[ 19.971202] The buggy address is located 140 bytes inside of
[ 19.971202] 224-byte region [
ffff888112862840,
ffff888112862920)
[ 19.972344] The buggy address belongs to the page:
[ 19.972820] page:
ffffea00044a1800 refcount:1 mapcount:0 mapping:
ffff88811a2bd1c0 index:0xffff8881128625c0 compo0
[ 19.973930] flags: 0x8000000000010200(slab|head)
[ 19.974388] raw:
8000000000010200 ffff88811a2ed650 ffff88811a2ed650 ffff88811a2bd1c0
[ 19.975151] raw:
ffff8881128625c0 0000000000190013 00000001ffffffff 0000000000000000
[ 19.975915] page dumped because: kasan: bad access detected
[ 19.976461] page_owner tracks the page as allocated
[ 19.976946] page last allocated via order 2, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NO)
[ 19.978332] prep_new_page+0x24b/0x330
[ 19.978707] get_page_from_freelist+0x2057/0x2c90
[ 19.979170] __alloc_pages_nodemask+0x218/0x590
[ 19.979619] new_slab+0x9d/0x300
[ 19.979948] ___slab_alloc.constprop.0+0x2f9/0x6f0
[ 19.980421] __slab_alloc.constprop.0+0x30/0x60
[ 19.980870] kmem_cache_alloc+0x201/0x230
[ 19.981269] __alloc_skb+0x91/0x510
[ 19.981620] alloc_skb_with_frags+0x78/0x4a0
[ 19.982043] sock_alloc_send_pskb+0x5eb/0x750
[ 19.982476] unix_stream_sendmsg+0x399/0x7f0
[ 19.982904] sock_sendmsg+0xe2/0x110
[ 19.983262] ____sys_sendmsg+0x4de/0x6d0
[ 19.983660] ___sys_sendmsg+0xe4/0x160
[ 19.984032] __sys_sendmsg+0xab/0x130
[ 19.984396] do_syscall_64+0xe7/0xae0
[ 19.984761] page last free stack trace:
[ 19.985142] __free_pages_ok+0x432/0xbc0
[ 19.985533] qlist_free_all+0x56/0xc0
[ 19.985907] quarantine_reduce+0x149/0x170
[ 19.986315] __kasan_kmalloc.constprop.0+0x9e/0xd0
[ 19.986791] kmem_cache_alloc+0xe4/0x230
[ 19.987182] prepare_creds+0x24/0x440
[ 19.987548] do_faccessat+0x80/0x590
[ 19.987906] do_syscall_64+0xe7/0xae0
[ 19.988276] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 19.988775]
[ 19.988930] Memory state around the buggy address:
[ 19.989402]
ffff888112862780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 19.990111]
ffff888112862800: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
[ 19.990822] >
ffff888112862880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 19.991529] ^
[ 19.992081]
ffff888112862900: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
[ 19.992796]
ffff888112862980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 5a781ccbd19e ("tc: Add support for configuring the taprio scheduler")
Reported-by: Michael Schmidt <michael.schmidt@eti.uni-siegen.de>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 12 Mar 2020 16:59:36 +0000 (09:59 -0700)]
Merge tag 'for-linus-5.6-2' of git://github.com/cminyard/linux-ipmi
Pull IPMI fix from Corey Minyard:
"Fix a message spew on some system
The call to platform_get_irq() was changed to print a log if the
interrupt was not available, and that was causing bogus messages to
spew out for the IPMI driver. People have requested that this get in
to 5.6 so I'm sending it along"
* tag 'for-linus-5.6-2' of git://github.com/cminyard/linux-ipmi:
ipmi_si: Avoid spurious errors for optional IRQs
Johannes Berg [Thu, 12 Mar 2020 08:04:08 +0000 (09:04 +0100)]
wlcore: remove stray plus sign
The commit mentioned below added a stray plus sign, likely
due to some conflict resolution (i.e. as a leftover from a
unified diff), which was harmless since it was just used as
an integer constant modifier. Remove it anyway, now that I
stumbled across it.
Fixes: cf33a7728bf2 ("wlcore: mesh: Add support for RX Broadcast Key")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Linus Torvalds [Thu, 12 Mar 2020 16:25:55 +0000 (09:25 -0700)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a build problem with x86/curve25519"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: x86/curve25519 - support assemblers with no adx support
Larry Finger [Wed, 19 Feb 2020 20:00:41 +0000 (14:00 -0600)]
rtlwifi: rtl8188ee: Fix regression due to commit
d1d1a96bdb44
For some unexplained reason, commit
d1d1a96bdb44 ("rtlwifi: rtl8188ee:
Remove local configuration variable") broke at least one system. As
the only net effect of the change was to remove 2 bytes from the start
of struct phy_status_rpt, this patch adds 2 bytes of padding at the
beginning of the struct.
Fixes: d1d1a96bdb44 ("rtlwifi: rtl8188ee: Remove local configuration variable")
Cc: Stable <stable@vger.kernel.org> # V5.4+
Reported-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Tested-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chris Packham [Wed, 11 Mar 2020 20:05:46 +0000 (09:05 +1300)]
net: mvmdio: avoid error message for optional IRQ
Per the dt-binding the interrupt is optional so use
platform_get_irq_optional() instead of platform_get_irq(). Since
commit
7723f4c5ecdb ("driver core: platform: Add an error message to
platform_get_irq*()") platform_get_irq() produces an error message
orion-mdio
f1072004.mdio: IRQ index 0 not found
which is perfectly normal if one hasn't specified the optional property
in the device tree.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 11 Mar 2020 20:02:31 +0000 (21:02 +0100)]
net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register
Only the bottom 12 bits contain the ATU bin occupancy statistics. The
upper bits need masking off.
Fixes: e0c69ca7dfbb ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 11 Mar 2020 18:44:26 +0000 (11:44 -0700)]
net: memcg: fix lockdep splat in inet_csk_accept()
Locking newsk while still holding the listener lock triggered
a lockdep splat [1]
We can simply move the memcg code after we release the listener lock,
as this can also help if multiple threads are sharing a common listener.
Also fix a typo while reading socket sk_rmem_alloc.
[1]
WARNING: possible recursive locking detected
5.6.0-rc3-syzkaller #0 Not tainted
--------------------------------------------
syz-executor598/9524 is trying to acquire lock:
ffff88808b5b8b90 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline]
ffff88808b5b8b90 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x69f/0xd30 net/ipv4/inet_connection_sock.c:492
but task is already holding lock:
ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline]
ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x8d/0xd30 net/ipv4/inet_connection_sock.c:445
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(sk_lock-AF_INET6);
lock(sk_lock-AF_INET6);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by syz-executor598/9524:
#0:
ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline]
#0:
ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x8d/0xd30 net/ipv4/inet_connection_sock.c:445
stack backtrace:
CPU: 0 PID: 9524 Comm: syz-executor598 Not tainted 5.6.0-rc3-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x188/0x20d lib/dump_stack.c:118
print_deadlock_bug kernel/locking/lockdep.c:2370 [inline]
check_deadlock kernel/locking/lockdep.c:2411 [inline]
validate_chain kernel/locking/lockdep.c:2954 [inline]
__lock_acquire.cold+0x114/0x288 kernel/locking/lockdep.c:3954
lock_acquire+0x197/0x420 kernel/locking/lockdep.c:4484
lock_sock_nested+0xc5/0x110 net/core/sock.c:2947
lock_sock include/net/sock.h:1541 [inline]
inet_csk_accept+0x69f/0xd30 net/ipv4/inet_connection_sock.c:492
inet_accept+0xe9/0x7c0 net/ipv4/af_inet.c:734
__sys_accept4_file+0x3ac/0x5b0 net/socket.c:1758
__sys_accept4+0x53/0x90 net/socket.c:1809
__do_sys_accept4 net/socket.c:1821 [inline]
__se_sys_accept4 net/socket.c:1818 [inline]
__x64_sys_accept4+0x93/0xf0 net/socket.c:1818
do_syscall_64+0xf6/0x790 arch/x86/entry/common.c:294
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x4445c9
Code: e8 0c 0d 03 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007ffc35b37608 EFLAGS:
00000246 ORIG_RAX:
0000000000000120
RAX:
ffffffffffffffda RBX:
0000000000000003 RCX:
00000000004445c9
RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000000000000003
RBP:
0000000000000000 R08:
0000000000306777 R09:
0000000000306777
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00000000004053d0 R14:
0000000000000000 R15:
0000000000000000
Fixes: d752a4986532 ("net: memcg: late association of sock to memcg")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Shakeel Butt <shakeelb@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 12 Mar 2020 06:52:32 +0000 (23:52 -0700)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2020-03-11
please apply the following patch series for qeth to netdev's net tree.
Just one fix to get the RX buffer pool resizing right, with two
preparatory cleanups.
This is on the larger side given where we are in the -rc cycle, but a
big chunk of the delta is just refactoring to make the fix look nice.
I intentionally split these off from yesterday's series. No objections
if you'd rather punt them to net-next, the series should apply cleanly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 11 Mar 2020 17:07:11 +0000 (18:07 +0100)]
s390/qeth: implement smarter resizing of the RX buffer pool
The RX buffer pool is allocated in qeth_alloc_qdio_queues().
A subsequent pool resizing is then handled in a very simple way:
first free the current pool, then allocate a new pool of the requested
size.
There's two ways where this can go wrong:
1. if the resize action happens _before_ the initial pool was allocated,
then a subsequent initialization will call qeth_alloc_qdio_queues()
and fill the pool with a second(!) set of pages. We consume twice the
planned amount of memory.
This is easy to fix - just skip the resizing if the queues haven't
been allocated yet.
2. if the initial pool was created by qeth_alloc_qdio_queues() but a
subsequent resizing fails, then the device has no(!) RX buffer pool.
The next initialization will _not_ call qeth_alloc_qdio_queues(), and
attempting to back the RX buffers with pages in
qeth_init_qdio_queues() will fail.
Not very difficult to fix either - instead of re-allocating the whole
pool, just allocate/free as many entries to match the desired size.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 11 Mar 2020 17:07:10 +0000 (18:07 +0100)]
s390/qeth: refactor buffer pool code
In preparation for a subsequent fix, split out helpers to allocate/free
individual pool entries.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Wed, 11 Mar 2020 17:07:09 +0000 (18:07 +0100)]
s390/qeth: use page pointers to manage RX buffer pool
The RX buffer elements are always backed with full pages, reflect this
in the pointer type.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Lungaroni [Wed, 11 Mar 2020 16:54:06 +0000 (17:54 +0100)]
seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number
The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Wed, 11 Mar 2020 15:24:24 +0000 (16:24 +0100)]
net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed
By default, DSA drivers should configure CPU and DSA ports to their
maximum speed. In many configurations this is sufficient to make the
link work.
In some cases it is necessary to configure the link to run slower,
e.g. because of limitations of the SoC it is connected to. Or back to
back PHYs are used and the PHY needs to be driven in order to
establish link. In this case, phylink is used.
Only instantiate phylink if it is required. If there is no PHY, or no
fixed link properties, phylink can upset a link which works in the
default configuration.
Fixes: 0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 9 Mar 2020 15:34:35 +0000 (11:34 -0400)]
net/packet: tpacket_rcv: do not increment ring index on drop
In one error case, tpacket_rcv drops packets after incrementing the
ring producer index.
If this happens, it does not update tp_status to TP_STATUS_USER and
thus the reader is stalled for an iteration of the ring, causing out
of order arrival.
The only such error path is when virtio_net_hdr_from_skb fails due
to encountering an unknown GSO type.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dominik Czarnota [Mon, 9 Mar 2020 15:22:50 +0000 (16:22 +0100)]
sxgbe: Fix off by one in samsung driver strncpy size arg
This patch fixes an off-by-one error in strncpy size argument in
drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c. The issue is that in:
strncmp(opt, "eee_timer:", 6)
the passed string literal: "eee_timer:" has 10 bytes (without the NULL
byte) and the passed size argument is 6. As a result, the logic will
also accept other, malformed strings, e.g. "eee_tiXXX:".
This bug doesn't seem to have any security impact since its present in
module's cmdline parsing code.
Signed-off-by: Dominik Czarnota <dominik.b.czarnota@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amol Grover [Thu, 12 Mar 2020 05:34:20 +0000 (11:04 +0530)]
net: caif: Add lockdep expression to RCU traversal primitive
caifdevs->list is traversed using list_for_each_entry_rcu()
outside an RCU read-side critical section but under the
protection of rtnl_mutex. Hence, add the corresponding lockdep
expression to silence the following false-positive warning:
[ 10.868467] =============================
[ 10.869082] WARNING: suspicious RCU usage
[ 10.869817]
5.6.0-rc1-00177-g06ec0a154aae4 #1 Not tainted
[ 10.870804] -----------------------------
[ 10.871557] net/caif/caif_dev.c:115 RCU-list traversed in non-reader section!!
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amol Grover <frextrite@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 11 Mar 2020 23:37:02 +0000 (16:37 -0700)]
MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer
Remove Sathya Perla, sathya.perla@broadcom.com is bouncing.
The driver has 3 more maintainers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 11 Mar 2020 03:36:16 +0000 (20:36 -0700)]
net: fec: validate the new settings in fec_enet_set_coalesce()
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22fc ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai [Wed, 5 Feb 2020 09:31:46 +0000 (10:31 +0100)]
ipmi_si: Avoid spurious errors for optional IRQs
Although the IRQ assignment in ipmi_si driver is optional,
platform_get_irq() spews error messages unnecessarily:
ipmi_si dmi-ipmi-si.0: IRQ index 0 not found
Fix this by switching to platform_get_irq_optional().
Cc: stable@vger.kernel.org # 5.4.x
Cc: John Donnelly <john.p.donnelly@oracle.com>
Fixes: 7723f4c5ecdb ("driver core: platform: Add an error message to platform_get_irq*()")
Reported-and-tested-by: Patrick Vo <patrick.vo@hpe.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-Id: <
20200205093146.1352-1-tiwai@suse.de>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Dave Airlie [Thu, 12 Mar 2020 01:02:46 +0000 (11:02 +1000)]
Merge tag 'exynos-drm-fixes-for-v5.6-rc5-v2' of git://git./linux/kernel/git/daeinki/drm-exynos into drm-fixes
Fix IOMMU initialization failure when Exynos DRM driver is rebound,
and also fix memory leak to iommu mapping object, which was
detected by kmemleak detector.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1583887109-4148-1-git-send-email-inki.dae@samsung.com
Chris Wilson [Tue, 10 Mar 2020 10:17:20 +0000 (10:17 +0000)]
drm/i915: Defer semaphore priority bumping to a workqueue
Since the semaphore fence may be signaled from inside an interrupt
handler from inside a request holding its request->lock, we cannot then
enter into the engine->active.lock for processing the semaphore priority
bump as we may traverse our call tree and end up on another held
request.
CPU 0:
[ 2243.218864] _raw_spin_lock_irqsave+0x9a/0xb0
[ 2243.218867] i915_schedule_bump_priority+0x49/0x80 [i915]
[ 2243.218869] semaphore_notify+0x6d/0x98 [i915]
[ 2243.218871] __i915_sw_fence_complete+0x61/0x420 [i915]
[ 2243.218874] ? kmem_cache_free+0x211/0x290
[ 2243.218876] i915_sw_fence_complete+0x58/0x80 [i915]
[ 2243.218879] dma_i915_sw_fence_wake+0x3e/0x80 [i915]
[ 2243.218881] signal_irq_work+0x571/0x690 [i915]
[ 2243.218883] irq_work_run_list+0xd7/0x120
[ 2243.218885] irq_work_run+0x1d/0x50
[ 2243.218887] smp_irq_work_interrupt+0x21/0x30
[ 2243.218889] irq_work_interrupt+0xf/0x20
CPU 1:
[ 2242.173107] _raw_spin_lock+0x8f/0xa0
[ 2242.173110] __i915_request_submit+0x64/0x4a0 [i915]
[ 2242.173112] __execlists_submission_tasklet+0x8ee/0x2120 [i915]
[ 2242.173114] ? i915_sched_lookup_priolist+0x1e3/0x2b0 [i915]
[ 2242.173117] execlists_submit_request+0x2e8/0x2f0 [i915]
[ 2242.173119] submit_notify+0x8f/0xc0 [i915]
[ 2242.173121] __i915_sw_fence_complete+0x61/0x420 [i915]
[ 2242.173124] ? _raw_spin_unlock_irqrestore+0x39/0x40
[ 2242.173137] i915_sw_fence_complete+0x58/0x80 [i915]
[ 2242.173140] i915_sw_fence_commit+0x16/0x20 [i915]
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1318
Fixes: b7404c7ecb38 ("drm/i915: Bump ready tasks ahead of busywaits")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310101720.9944-1-chris@chris-wilson.co.uk
(cherry picked from commit
209df10bb4536c81c2540df96c02cd079435357f)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Fri, 6 Mar 2020 15:46:47 +0000 (15:46 +0000)]
drm/i915/gt: Close race between cacheline_retire and free
If the cacheline may still be busy, atomically mark it for future
release, and only if we can determine that it will never be used again,
immediately free it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1392
Fixes: ebece7539242 ("drm/i915: Keep timeline HWSP allocated until idle across the system")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Link: https://patchwork.freedesktop.org/patch/msgid/20200306154647.3528345-1-chris@chris-wilson.co.uk
(cherry picked from commit
2d4bd971f5baa51418625f379a69f5d58b5a0450)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Fri, 6 Mar 2020 11:30:10 +0000 (11:30 +0000)]
drm/i915/execlists: Enable timeslice on partial virtual engine dequeue
If we stop filling the ELSP due to an incompatible virtual engine
request, check if we should enable the timeslice on behalf of the queue.
This fixes the case where we are inspecting the last->next element when
we know that the last element is the last request in the execution queue,
and so decided we did not need to enable timeslicing despite the intent
to do so!
Fixes: 8ee36e048c98 ("drm/i915/execlists: Minimalistic timeslicing")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200306113012.3184606-1-chris@chris-wilson.co.uk
(cherry picked from commit
3df2deed411e0f1b7312baf0139aab8bba4c0410)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Matthew Auld [Thu, 5 Mar 2020 20:35:34 +0000 (20:35 +0000)]
drm/i915: be more solid in checking the alignment
The alignment is u64, and yet is_power_of_2() assumes unsigned long,
which might give different results between 32b and 64b kernel.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305203534.210466-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit
2920516b2f719546f55079bc39a7fe409d9e80ab)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tina Zhang [Thu, 27 Feb 2020 01:00:41 +0000 (09:00 +0800)]
drm/i915/gvt: Fix dma-buf display blur issue on CFL
Commit
c3b5a8430daad ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
added the support on CFL. The vgpu emulation hotplug support on CFL was
supposed to be included in that patch. Without the vgpu emulation
hotplug support, the dma-buf based display gives us a blur face.
So fix this issue by adding the vgpu emulation hotplug support on CFL.
Fixes: c3b5a8430daad ("drm/i915/gvt: Enable gfx virtualiztion for CFL")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20200227010041.32248-1-tina.zhang@intel.com
(cherry picked from commit
135dde8853c7e00f6002e710f7e4787ed8585c0e)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Thu, 5 Mar 2020 13:48:22 +0000 (13:48 +0000)]
drm/i915: Return early for await_start on same timeline
Requests within a timeline are ordered by that timeline, so awaiting for
the start of a request within the timeline is a no-op. This used to work
by falling out of the mutex_trylock() as the signaler and waiter had the
same timeline and not returning an error.
Fixes: 6a79d848403d ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305134822.2750496-1-chris@chris-wilson.co.uk
(cherry picked from commit
ab7a69020fb5d5c7ba19fba60f62fd6f9ca9f779)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Chris Wilson [Thu, 5 Mar 2020 10:42:10 +0000 (10:42 +0000)]
drm/i915: Actually emit the await_start
Fix the inverted test to emit the wait on the end of the previous
request if we /haven't/ already.
Fixes: 6a79d848403d ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.5+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305104210.2619967-1-chris@chris-wilson.co.uk
(cherry picked from commit
07e9c59d63df6a1c44c1975c01827ba18b69270a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Nathan Chancellor [Tue, 10 Mar 2020 22:06:54 +0000 (15:06 -0700)]
dpaa_eth: Remove unnecessary boolean expression in dpaa_get_headroom
Clang warns:
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:2860:9: warning:
converting the result of '?:' with integer constants to a boolean always
evaluates to 'true' [-Wtautological-constant-compare]
return DPAA_FD_DATA_ALIGNMENT ? ALIGN(headroom,
^
drivers/net/ethernet/freescale/dpaa/dpaa_eth.c:131:34: note: expanded
from macro 'DPAA_FD_DATA_ALIGNMENT'
\#define DPAA_FD_DATA_ALIGNMENT (fman_has_errata_a050385() ? 64 : 16)
^
1 warning generated.
This was exposed by commit
3c68b8fffb48 ("dpaa_eth: FMan erratum
A050385
workaround") even though it appears to have been an issue since the
introductory commit
9ad1a3749333 ("dpaa_eth: add support for DPAA
Ethernet") since DPAA_FD_DATA_ALIGNMENT has never been able to be zero.
Just replace the whole boolean expression with the true branch, as it is
always been true.
Link: https://github.com/ClangBuiltLinux/linux/issues/928
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 11 Mar 2020 20:35:34 +0000 (13:35 -0700)]
Merge tag 'fscrypt-for-linus' of git://git./fs/fscrypt/fscrypt
Pull fscrypt fix from Eric Biggers:
"Fix a bug where if userspace is writing to encrypted files while the
FS_IOC_REMOVE_ENCRYPTION_KEY ioctl (introduced in v5.4) is running,
dirty inodes could be evicted, causing writes could be lost or the
filesystem to hang due to a use-after-free. This was encountered
during real-world use, not just theoretical.
Tested with the existing fscrypt xfstests, and with a new xfstest I
wrote to reproduce this bug. This fix does expose an existing bug with
'-o lazytime' that Ted is working on fixing, but this fix is more
critical and needed anyway regardless of the lazytime fix"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
fscrypt: don't evict dirty inodes after removing key
David S. Miller [Wed, 11 Mar 2020 19:29:03 +0000 (12:29 -0700)]
Merge tag 'mac80211-for-net-2020-03-11' of git://git./linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A couple of fixes:
* three netlink validation fixes
* a mesh path selection fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 11 Mar 2020 17:00:41 +0000 (10:00 -0700)]
Merge tag 'for-linus-2020-03-10' of git://git./linux/kernel/git/brauner/linux
Pull thread fix from Christian Brauner:
"This contains a single fix for a regression which was introduced when
we introduced the ability to select a specific pid at process creation
time.
When this feature is requested, the error value will be set to -EPERM
after exiting the pid allocation loop. This caused EPERM to be
returned when e.g. the init process/child subreaper of the pid
namespace has already died where we used to return ENOMEM before.
The first patch here simply fixes the regression by unconditionally
setting the return value back to ENOMEM again once we've successfully
allocated the requested pid number. This should be easy to backport to
v5.5.
The second patch adds a comment explaining that we must keep returning
ENOMEM since we've been doing it for a long time and have explicitly
documented this behavior for userspace. This seemed worthwhile because
we now have at least two separate example where people tried to change
the return value to something other than ENOMEM (The first version of
the regression fix did that too and the commit message links to an
earlier patch that tried to do the same.).
I have a simple regression test to make sure we catch this regression
in the future but since that introduces a whole new selftest subdir
and test files I'll keep this for v5.7"
* tag 'for-linus-2020-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
pid: make ENOMEM return value more obvious
pid: Fix error return value in some cases
Linus Torvalds [Wed, 11 Mar 2020 16:54:59 +0000 (09:54 -0700)]
Merge tag 'trace-v5.6-rc4' of git://git./linux/kernel/git/rostedt/linux-trace
Pull ftrace fix from Steven Rostedt:
"Have ftrace lookup_rec() return a consistent record otherwise it can
break live patching"
* tag 'trace-v5.6-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Return the first found result in lookup_rec()
Linus Torvalds [Wed, 11 Mar 2020 16:49:47 +0000 (09:49 -0700)]
Merge tag 'mips_fixes_5.6.1' of git://git./linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
"A few MIPS fixes:
- DT fixes for CI20
- Fix command line handling
- Correct patchwork URL"
* tag 'mips_fixes_5.6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MAINTAINERS: Correct MIPS patchwork URL
MIPS: DTS: CI20: fix interrupt for pcf8563 RTC
MIPS: DTS: CI20: fix PMU definitions for ACT8600
MIPS: Fix CONFIG_MIPS_CMDLINE_DTB_EXTEND handling
Linus Torvalds [Wed, 11 Mar 2020 16:45:38 +0000 (09:45 -0700)]
Merge tag 'pinctrl-v5.6-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some pin control fixes for the v5.6 series.
It comes down to memory leaks in the core and driver fixes. Some
should have been sent earlier but they kept piling up and the world is
just so full of distractions these days.
- Fix some inverted pins in the Meson GLX driver.
- Align the i.MX SC message structs causing warnings from KASan.
- Balance the kref in pinctrl hogs so they are actually free:d when
removing a pin control module. We haven't seen it before as people
don't use modules for pin control that much, I think.
- Add a missing call to pinctrl_unregister_mappings() another memory
leak when using modules.
- Fix the fwspec parsing in the Qualcomm driver.
- Fix a syntax error in the Falcon driver.
- Assign .irq_eoi conditionally in the Qualcomm driver, fixing a bug
affecting elder Qualcomm platforms"
* tag 'pinctrl-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: Assign irq_eoi conditionally
pinctrl: falcon: fix syntax error
pinctrl: qcom: ssbi-gpio: Fix fwspec parsing bug
pinctrl: madera: Add missing call to pinctrl_unregister_mappings
pinctrl: core: Remove extra kref_get which blocks hogs being freed
pinctrl: imx: scu: Align imx sc msg structs to 4
pinctrl: meson-gxl: fix GPIOX sdio pins
Christoph Hellwig [Wed, 11 Mar 2020 16:07:10 +0000 (17:07 +0100)]
driver code: clarify and fix platform device DMA mask allocation
This does three inter-related things to clarify the usage of the
platform device dma_mask field. In the process, fix the bug introduced
by
cdfee5623290 ("driver core: initialize a default DMA mask for
platform device") that caused Artem Tashkinov's laptop to not boot with
newer Fedora kernels.
This does:
- First off, rename the field to "platform_dma_mask" to make it
greppable.
We have way too many different random fields called "dma_mask" in
various data structures, where some of them are actual masks, and
some of them are just pointers to the mask. And the structures all
have pointers to each other, or embed each other inside themselves,
and "pdev" sometimes means "platform device" and sometimes it means
"PCI device".
So to make it clear in the code when you actually use this new field,
give it a unique name (it really should be something even more unique
like "platform_device_dma_mask", since it's per platform device, not
per platform, but that gets old really fast, and this is unique
enough in context).
To further clarify when the field gets used, initialize it when we
actually start using it with the default value.
- Then, use this field instead of the random one-off allocation in
platform_device_register_full() that is now unnecessary since we now
already have a perfectly fine allocation for it in the platform
device structure.
- The above then allows us to fix the actual bug, where the error path
of platform_device_register_full() would unconditionally free the
platform device DMA allocation with 'kfree()'.
That kfree() was dont regardless of whether the allocation had been
done earlier with the (now removed) kmalloc, or whether
setup_pdev_dma_masks() had already been used and the dma_mask pointer
pointed to the mask that was part of the platform device.
It seems most people never triggered the error path, or only triggered
it from a call chain that set an explicit pdevinfo->dma_mask value (and
thus caused the unnecessary allocation that was "cleaned up" in the
error path) before calling platform_device_register_full().
Robin Murphy points out that in Artem's case the wdat_wdt driver failed
in platform_device_add(), and that was the one that had called
platform_device_register_full() with pdevinfo.dma_mask = 0, and would
have caused that kfree() of pdev.dma_mask corrupting the heap.
A later unrelated kmalloc() then oopsed due to the heap corruption.
Fixes: cdfee5623290 ("driver core: initialize a default DMA mask for platform device")
Reported-bisected-and-tested-by: Artem S. Tashkinov <aros@gmx.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Artem Savkov [Fri, 6 Mar 2020 17:43:17 +0000 (18:43 +0100)]
ftrace: Return the first found result in lookup_rec()
It appears that ip ranges can overlap so. In that case lookup_rec()
returns whatever results it got last even if it found nothing in last
searched page.
This breaks an obscure livepatch late module patching usecase:
- load livepatch
- load the patched module
- unload livepatch
- try to load livepatch again
To fix this return from lookup_rec() as soon as it found the record
containing searched-for ip. This used to be this way prior lookup_rec()
introduction.
Link: http://lkml.kernel.org/r/20200306174317.21699-1-asavkov@redhat.com
Cc: stable@vger.kernel.org
Fixes: 7e16f581a817 ("ftrace: Separate out functionality from ftrace_location_range()")
Signed-off-by: Artem Savkov <asavkov@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
John Fastabend [Tue, 10 Mar 2020 16:41:48 +0000 (09:41 -0700)]
bpf, sockmap: Remove bucket->lock from sock_{hash|map}_free
The bucket->lock is not needed in the sock_hash_free and sock_map_free
calls, in fact it is causing a splat due to being inside rcu block.
| BUG: sleeping function called from invalid context at net/core/sock.c:2935
| in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 62, name: kworker/0:1
| 3 locks held by kworker/0:1/62:
| #0:
ffff88813b019748 ((wq_completion)events){+.+.}, at: process_one_work+0x1d7/0x5e0
| #1:
ffffc900000abe50 ((work_completion)(&map->work)){+.+.}, at: process_one_work+0x1d7/0x5e0
| #2:
ffff8881381f6df8 (&stab->lock){+...}, at: sock_map_free+0x26/0x180
| CPU: 0 PID: 62 Comm: kworker/0:1 Not tainted
5.5.0-04008-g7b083332376e #454
| Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20190727_073836-buildvm-ppc64le-16.ppc.fedoraproject.org-3.fc31 04/01/2014
| Workqueue: events bpf_map_free_deferred
| Call Trace:
| dump_stack+0x71/0xa0
| ___might_sleep.cold+0xa6/0xb6
| lock_sock_nested+0x28/0x90
| sock_map_free+0x5f/0x180
| bpf_map_free_deferred+0x58/0x80
| process_one_work+0x260/0x5e0
| worker_thread+0x4d/0x3e0
| kthread+0x108/0x140
| ? process_one_work+0x5e0/0x5e0
| ? kthread_park+0x90/0x90
| ret_from_fork+0x3a/0x50
The reason we have stab->lock and bucket->locks in sockmap code is to
handle checking EEXIST in update/delete cases. We need to be careful during
an update operation that we check for EEXIST and we need to ensure that the
psock object is not in some partial state of removal/insertion while we do
this. So both map_update_common and sock_map_delete need to guard from being
run together potentially deleting an entry we are checking, etc. But by the
time we get to the tear-down code in sock_{ma[|hash}_free we have already
disconnected the map and we just did synchronize_rcu() in the line above so
no updates/deletes should be in flight. Because of this we can drop the
bucket locks from the map free'ing code, noting no update/deletes can be
in-flight.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: Jakub Sitnicki <jakub@cloudflare.com>
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/158385850787.30597.8346421465837046618.stgit@john-Precision-5820-Tower
Nicolas Cavallari [Thu, 5 Mar 2020 14:04:09 +0000 (15:04 +0100)]
mac80211: Do not send mesh HWMP PREQ if HWMP is disabled
When trying to transmit to an unknown destination, the mesh code would
unconditionally transmit a HWMP PREQ even if HWMP is not the current
path selection algorithm.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20200305140409.12204-1-cavallar@lri.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jakub Kicinski [Tue, 3 Mar 2020 05:10:58 +0000 (21:10 -0800)]
nl80211: add missing attribute validation for channel switch
Add missing attribute validation for NL80211_ATTR_OPER_CLASS
to the netlink policy.
Fixes: 1057d35ede5d ("cfg80211: introduce TDLS channel switch commands")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20200303051058.4089398-4-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jakub Kicinski [Tue, 3 Mar 2020 05:10:57 +0000 (21:10 -0800)]
nl80211: add missing attribute validation for beacon report scanning
Add missing attribute validation for beacon report scanning
to the netlink policy.
Fixes: 1d76250bd34a ("nl80211: support beacon report scanning")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20200303051058.4089398-3-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jakub Kicinski [Tue, 3 Mar 2020 05:10:56 +0000 (21:10 -0800)]
nl80211: add missing attribute validation for critical protocol indication
Add missing attribute validation for critical protocol fields
to the netlink policy.
Fixes: 5de17984898c ("cfg80211: introduce critical protocol indication from user-space")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20200303051058.4089398-2-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
David S. Miller [Tue, 10 Mar 2020 23:07:49 +0000 (16:07 -0700)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2020-03-10
This fixes three minor issues:
1) a setup parameter gets cleared unnecessarily when the HW config
changes,
2) insufficient error handling when initially filling the RX ring, and
3) a rarely used worker that needs to be cancelled during tear down.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 10 Mar 2020 17:38:03 +0000 (18:38 +0100)]
s390/qeth: cancel RX reclaim work earlier
When qeth's napi poll code fails to refill an entirely empty RX ring, it
kicks off buffer_reclaim_work to try again later.
Make sure that this worker is cancelled when setting the qeth device
offline. Otherwise a RX refill action can unexpectedly end up running
concurrently to bigger re-configurations (eg. resizing the buffer pool),
without any locking.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 10 Mar 2020 17:38:02 +0000 (18:38 +0100)]
s390/qeth: handle error when backing RX buffer
qeth_init_qdio_queues() fills the RX ring with an initial set of
RX buffers. If qeth_init_input_buffer() fails to back one of the RX
buffers with memory, we need to bail out and report the error.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 10 Mar 2020 17:38:01 +0000 (18:38 +0100)]
s390/qeth: don't reset default_out_queue
When an OSA device in prio-queue setup is reduced to 1 TX queue due to
HW restrictions, we reset its the default_out_queue to 0.
In the old code this was needed so that qeth_get_priority_queue() gets
the queue selection right. But with proper multiqueue support we already
reduced dev->real_num_tx_queues to 1, and so the stack puts all traffic
on txq 0 without even calling .ndo_select_queue.
Thus we can preserve the user's configuration, and apply it if the OSA
device later re-gains support for multiple TX queues.
Fixes: 73dc2daf110f ("s390/qeth: add TX multiqueue support for OSA devices")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 10 Mar 2020 22:59:32 +0000 (15:59 -0700)]
Merge branch 'MACSec-bugfixes-related-to-MAC-address-change'
Igor Russkikh says:
====================
MACSec bugfixes related to MAC address change
We found out that there's an issue in MACSec code when the MAC address
is changed.
Both s/w and offloaded implementations don't update SCI when the MAC
address changes at the moment, but they should do so, because SCI contains
MAC in its first 6 octets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Tue, 10 Mar 2020 15:22:25 +0000 (18:22 +0300)]
net: macsec: invoke mdo_upd_secy callback when mac address changed
Notify the offload engine about MAC address change to reconfigure it
accordingly.
Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Tue, 10 Mar 2020 15:22:24 +0000 (18:22 +0300)]
net: macsec: update SCI upon MAC address change.
SCI should be updated, because it contains MAC in its first 6 octets.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Juliet Kim [Tue, 10 Mar 2020 14:23:58 +0000 (09:23 -0500)]
ibmvnic: Do not process device remove during device reset
The ibmvnic driver does not check the device state when the device
is removed. If the device is removed while a device reset is being
processed, the remove may free structures needed by the reset,
causing an oops.
Fix this by checking the device state before processing device remove.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>