[media] af9035: correct TS mode handling

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: minor log writing changes

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: make checkpatch.pl happy!

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] af9035: implement I2C adapter read operation

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Add support for 'Digital Dual TV Receiver CTVDIGDUAL v2

Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value      :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value      :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested

Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: sign of CRL_FREQ doesn't depend on inversion

Contrary to CFR (derotator frequency), which changes signedness
depending on inversion, CRL_FREQ does not.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: use autodetected inversion instead of configured inversion

For consistency, it is necessary to use the autodetected inversion
instead of the configured one.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: store autodetected inversion while tuning in non S2 mode

In non S2 mode, the device is able to autodetect inversion. So
let's store it for tuning to S2 transponders.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: store successful inversion for next run

Usually, inversion doesn't change in a system. Storing the last
successful inversion value speeds up tuning of DVB-S2 transponders.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: allow minimum symbol rate of 2000000

Looks like product datasheets for tuners containing STB0899 are
suggesting specification for min. symbol rate of 2MS/s.
Some specs found here, all suggesting 2MS/s for min. symbol rate:
    Comtech DVBS2-6899
      http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
    TechniSat SkyStar HD2
      http://www.scaistar.com/skystar2/skystarhd2.htm
    Azurewave AD-SP400
      http://www.pulsat.com/products/AzureWave-AD%252dSP400-High-Definition-PC-Card.html
New patch:
This makes minimum symbol rate driver capabilities on par with some
accessible datasheet specifications*, and allows tuning on linux to
transponders that have symbol rate between 2000000-5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (2000000 < symbol rate < 5000000):
      * DVB/S  12507050 V  2532000 3/4
      * DVB/S2 12574000 V  4355000 3/4 8PSK
      * DVB/S  12593000 V  2500000 2/3
      * DVB/S  12596940 V  2848000 2/3
      * DVB/S  12600750 V  2500000 1/2
      * DVB/S  12675590 H  4248000 3/4
(*) Datasheet: http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
        Maximum Symbol Rate
        QPSK/LDPC/PCH: 20-30Mbps
        8PSK/LDPC/BCH: 10-30Mbps
        DVB: 2-45Mbps
             ^--------- min. symbol rate

Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: fix inversion enum values to match usage with CFR

Throughout the zig-zag-implementations, inversion is taken into
account when reading and writing the CFR register, which contains
the derotator frequency. As swapping IQ signals changes the sign
of that register for example, the idea is to compensate that sign
change by multiplying the register value with the inversion enum
value.
The current enum values 0 and 1 for IQ_SWAP_OFF and IQ_SWAP_ON
don't work in the case IQ_SWAP_OFF, due to the multiplication by
zero (I've only found a single device which actually uses
IQ_SWAP_OFF in it's config).
I've changed the enum values to +1 and -1 to accommodate to the
intended usage.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: enable auto inversion handling unconditionally

It seems that current inversion handling addresses only the signal
routing on the PCB, i. e. IQ signals are either swapped or not.
But when the device is operated in a Satellite Channel Router (SCR)
environment, an additional inversion is required due to the way how
the SCR works. Therefore it makes sense to me to always enable auto
inversion handling and drop the enum value IQ_SWAP_AUTO.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: allow minimum symbol rate of 1000000

This makes minimum symbol rate driver capabilities on par with
windows driver, and allows tuning on linux to transponders that
have symbol rate below 5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (1000000 < symbol rate < 5000000):
      * DVB/S  12507050 V  2532000 3/4
      * DVB/S2 12574000 V  4355000 3/4 8PSK
      * DVB/S  12593000 V  2500000 2/3
      * DVB/S  12596940 V  2848000 2/3
      * DVB/S  12600750 V  2500000 1/2
      * DVB/S  12675590 H  4248000 3/4

Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: sign extend raw CRL_FREQ value

Contrary to the chip's specs, the register's value is signed, so we
need to sign extend the value before using it in calculations like
when determining the offset frequency.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dma-buf: Cocci spatch "ptr_ret.spatch"

Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] r820t: do not double-free fe->tuner_priv in r820t_release()

fe->tuner_priv is already freed by hybrid_tuner_release_state().

Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib8000: Fix dib8000_set_frontend() never setting ret

drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’:
drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function
Remove the variable and return zero instead.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] uvcvideo: Fix open/close race condition

Maintaining the users count using an atomic variable makes sure that
access to the counter won't be racy, but doesn't serialize access to the
operations protected by the counter. This creates a race condition that
could result in the status URB being submitted multiple times.
Use a mutex to protect the users count and serialize access to the
status start and stop operations.

Reported-by: Shawn Nematbakhsh <shawnn@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] uvcvideo: quirk PROBE_DEF for Alienware X51 OmniVision webcam

BugLink: http://bugs.launchpad.net/bugs/1180409
OminiVision webcam 0x05a9:0x2643 needs the same UVC_QUIRK_PROBE_DEF
as other OmniVision models to work properly.

Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] uvcvideo: quirk PROBE_DEF for Dell Studio / OmniVision webcam

BugLink: https://bugs.launchpad.net/bugs/1168430
OminiVision webcam 0x05a9:0x264a (in Dell Studio Hybrid 140g) needs the
same UVC_QUIRK_PROBE_DEF as other OmniVision model to be recognized
consistently.

Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: do not call v4l2_m2m_job_finish from .job_abort

If we just declare the job finished here while the CODA is still
running, the call to v4l2_m2m_ctx_release in coda_release, which
is supposed to wait for a running job to finish, will return
immediately and free memory that the CODA is still using.
Just set the 'aborting' flag and let coda_irq_handler deal with it.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: replace completion with mutex

Not only do we need to wait for job completion when we want to
call a command on the CODA in start/stop_streaming, we also need
to make sure that a new job doesn't start before the command
finished.
Use a mutex to lock the coda command handling. On timeout, the
device_run job must be marked as finished and the mutex released,
as otherwise coda_release will block.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: add coda_encode_header helper function

In preparation for CODA7541 and CODA960 multi-stream support and for
replacement of the completion with a mutex lock, consolidate the
header encoding in a helper function.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: per-product list of codecs instead of list of formats

This patch adds a list of supported codecs per device type which is used to
determine the allowed pixel formats and maximum frame sizes depending on the
possible codecs. It allows frame sizes larger than 720 x 576 on CODA7 and adds
support for the YVU420 (planar YUV 4:2:0 with switched Cb and Cr) format.
Other uncompressed formats that could be added in the future are the chroma
interleaved NV12 and NV21 formats and the multiplanar variants YUV420M,
YVU420M, NV12M, and NV21M.
Further, rawstreamon is renamed to streamon_out and compstreamon is renamed
to streamon_cap in preparation for decoding support. The maximum encoded
frame buffer size is increased to 1 MiB.
Instead of tracking inst_type and codec across S_FMT calls, set the codec
and inst_type in start_streaming.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: simplify parameter buffer setup code

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: clear registers in coda_hw_init

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: stop setting bytesused in buf_prepare

The application must have filled the bytesused field,
don't overwrite it here.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: frame stride must be a multiple of 8

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: fix ENC_SEQ_OPTION for CODA7

GAMMA_OFFSET is different between CodaDx6 and CODA7.
Also, this is a bitfield.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: pci: remove duplicate checks for EPERM

This patch removes check for EPERM in dbg_g/s_register and
vidioc_g/s_register as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: usb: remove duplicate checks for EPERM in vidioc_g/s_register

This patch removes check for EPERM in vidioc_g/s_register
as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: dvb-frontends: remove duplicate checks for EPERM in dbg_g/s_register

This patch removes check for EPERM in dbg_g/s_register
as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: remove duplicate checks for EPERM in dbg_g/s_register

This patch removes check for EPERM in dbg_g/s_register of subdevice
drivers as this check is already performed by core.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: do not use v4l2_dev in coda_timeout

The timeout delayed work might be scheduled even after the v4l2 device is
released.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: fix error return value if v4l2_m2m_ctx_init fails

Use ret from the outer scope, instead of redefining it in the
conditional clause. That way the error value reaches the end of
the function as intended.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: set umask 0644 on debug module param

Otherwise module/coda/parameters/coda_debug won't show up in sysfs.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: enable dmabuf support

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: use devm_ioremap_resource

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] coda: v4l2-compliance fix: add bus_info prefix 'platform'

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: gpio-ir-recv: Remove redundant platform_set_drvdata()

Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] timblogiw: Remove redundant platform_set_drvdata()

Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bw-qcam: fix timestamp handling

bw-qcam didn't set the timestamp and it didn't set q->timestamp_type.

Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: tvp7002: rearrange description of structure members

This patch rearranges the description of field members of
struct tvp7002_config. Also as the all the fields where accepting
a value either 0/1, made the members as bool.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: tvp7002: remove duplicate define

this patch removes duplicate #define TVP7002_MODULE_NAME
form the driver file, which was also defined in media/tvp7002.h

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] hdpvr: Removed unnecessary use of kzalloc() in get_video_info()

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videodev2.h: fix typos

This patch fixes several typos in videodev2.h file

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sony-btf-mpx: Drop needless newline in param description

Module parameter descriptions need not be terminated with a newline.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] sta2x11_vip: fix error return code in sta2x11_vip_init_one()

The orig code will release all the resources if v4l2_device_register()
failed and return 0. But what we need in this case is to return an
negative error code to let the caller known we are failed.
So the patch save the return value of v4l2_device_register() to 'ret'
and return it when error.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] blackfin: fix error return code in bcap_probe()

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] ad9389b: fix error return code in ad9389b_probe()

Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vpif_capture: fix error return code in vpif_probe()

Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] vpif_display: fix error return code in vpif_probe()

Fix to return -ENODEV in the subdevice register error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: vb2: fix error return code in __vb2_init_fileio()

Fix to return -EINVAL in the get kernel address error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: fix hdpvr kconfig/build errors

Fix hdpvr build errors when CONFIG_I2C=m and VIDEO_V4L2=m and
VIDEO_HDPVR=y.
drivers/built-in.o: In function `hdpvr_disconnect':
hdpvr-core.c:(.text+0xef542): undefined reference to `v4l2_device_disconnect'
hdpvr-core.c:(.text+0xef57e): undefined reference to `i2c_del_adapter'
hdpvr-core.c:(.text+0xef58a): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `hdpvr_delete':
(.text+0xef5b9): undefined reference to `video_device_release'
drivers/built-in.o: In function `hdpvr_probe':
hdpvr-core.c:(.text+0xef63a): undefined reference to `v4l2_device_register'
hdpvr-core.c:(.text+0xefd97): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_s_ctrl':
hdpvr-video.c:(.text+0xf03c0): undefined reference to `v4l2_ctrl_activate'
drivers/built-in.o: In function `hdpvr_device_release':
hdpvr-video.c:(.text+0xf0470): undefined reference to `v4l2_device_unregister'
hdpvr-video.c:(.text+0xf0479): undefined reference to `v4l2_ctrl_handler_free'
hdpvr-video.c:(.text+0xf048f): undefined reference to `i2c_del_adapter'
drivers/built-in.o: In function `hdpvr_open':
hdpvr-video.c:(.text+0xf0570): undefined reference to `video_devdata'
hdpvr-video.c:(.text+0xf057b): undefined reference to `v4l2_fh_init'
hdpvr-video.c:(.text+0xf0583): undefined reference to `v4l2_fh_add'
drivers/built-in.o: In function `video_drvdata':
hdpvr-video.c:(.text+0xf08a0): undefined reference to `video_devdata'
drivers/built-in.o: In function `vidioc_s_dv_timings':
hdpvr-video.c:(.text+0xf0d34): undefined reference to `v4l_match_dv_timings'
drivers/built-in.o: In function `hdpvr_poll':
hdpvr-video.c:(.text+0xf1455): undefined reference to `v4l2_ctrl_poll'
drivers/built-in.o: In function `hdpvr_release':
hdpvr-video.c:(.text+0xf18f6): undefined reference to `v4l2_fh_release'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1be3): undefined reference to `v4l2_ctrl_handler_init_class'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c19): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c42): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1c6b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cac): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1cd5): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o:(.text+0xf1cfe): more undefined references to `v4l2_ctrl_new_std' follow
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d75): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1d9e): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1dc3): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1de5): undefined reference to `v4l2_ctrl_new_std_menu'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e18): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e4b): undefined reference to `v4l2_ctrl_new_std'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e90): undefined reference to `v4l2_ctrl_cluster'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1e98): undefined reference to `v4l2_ctrl_handler_setup'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1ec1): undefined reference to `video_device_alloc'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1f85): undefined reference to `__video_register_device'
drivers/built-in.o: In function `hdpvr_register_videodev':
(.text+0xf1fac): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `hdpvr_register_ir_tx_i2c':
(.text+0xf238f): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_ir_rx_i2c':
(.text+0xf2434): undefined reference to `i2c_new_device'
drivers/built-in.o: In function `hdpvr_register_i2c_adapter':
(.text+0xf2514): undefined reference to `i2c_add_adapter'
drivers/built-in.o:(.rodata+0x1b368): undefined reference to `video_ioctl2'
drivers/built-in.o:(.rodata+0x1b690): undefined reference to `v4l2_ctrl_log_status'
drivers/built-in.o:(.rodata+0x1b6f8): undefined reference to `v4l2_ctrl_subscribe_event'
drivers/built-in.o:(.rodata+0x1b700): undefined reference to `v4l2_event_unsubscribe'

Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Missing break statement added in smsdvb-main.c

Fix missing break that so that n_layers are not accidentally incorrect
Kernel version: v3.10-rc1

Signed-off-by: Jakob Normark <jakobnormark@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7115: Don't use a dynamic array

At least on s390, gcc complains about that:
    drivers/media/i2c/saa7115.c: In function 'saa711x_detect_chip.constprop.2':
    drivers/media/i2c/saa7115.c:1647:1: warning: 'saa711x_detect_chip.constprop.2' uses dynamic stack allocation [enabled by default]

While for me the above report seems utterly bogus, as the
compiler should be optimizing saa711x_detect_chip, merging
it with saa711x_detect_chip and changing:
char chip_ver[size - 1];
to
char chip_ver[16];

because this function is only called on this code snippet:
char name[17];
...
ident = saa711x_detect_chip(client, id, name, sizeof(name));

It seems that gcc is not optimizing it, at least on s390.

As getting rid of it is easy, let's do it.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videobuf-dma-contig: use vm_iomap_memory()

vm_iomap_memory() provides a better end user interface than
remap_pfn_range(), as it does the needed tests before doing
mmap.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] smscoreapi: Make Siano firmware load more verbose

If firmware load fails, report it as an error.

Signed-off-by: Roberto Alcantara <roberto@eletronica.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videobuf_vm_{open,close} race fixes

just use videobuf_queue_lock(map->q) to protect map->count; vm_area_operations
->open() and ->close() are called just under vma->vm_mm->mmap_sem, which
doesn't help the drivers at all, since clonal VMAs are normally in different
address spaces...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] stb0899: remove commented value from IQ_SWAP_ON/OFF usages

As the enum values have changed recently, the comments are void.

Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media/usb: fix kconfig dependencies

(a.k.a. Kconfig bool depending on a tristate considered harmful)
Fix various build errors when CONFIG_USB=m and media USB drivers
are builtin.  In this case, CONFIG_USB_ZR364XX=y,
CONFIG_VIDEO_PVRUSB2=y, and CONFIG_VIDEO_STK1160=y.
This is caused by (from drivers/media/usb/Kconfig):
menuconfig MEDIA_USB_SUPPORT
bool "Media USB Adapters"
depends on USB && MEDIA_SUPPORT
           =m     =y
so MEDIA_USB_SUPPORT=y and all following Kconfig 'source' lines
are included.  By adding an "if USB" guard around most of this file,
the needed dependencies are enforced.
drivers/built-in.o: In function `zr364xx_start_readpipe':
zr364xx.c:(.text+0xc726a): undefined reference to `usb_alloc_urb'
zr364xx.c:(.text+0xc72bb): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `zr364xx_stop_readpipe':
zr364xx.c:(.text+0xc72fd): undefined reference to `usb_kill_urb'
zr364xx.c:(.text+0xc7309): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `read_pipe_completion':
zr364xx.c:(.text+0xc7acc): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `send_control_msg.constprop.12':
zr364xx.c:(.text+0xc7d2f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_ctl_timeout':
pvrusb2-hdw.c:(.text+0xcadb6): undefined reference to `usb_unlink_urb'
pvrusb2-hdw.c:(.text+0xcadcb): undefined reference to `usb_unlink_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc42c): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc448): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc5f9): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc65a): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_create':
(.text+0xcc666): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_send_request_ex.part.22':
pvrusb2-hdw.c:(.text+0xccbe3): undefined reference to `usb_submit_urb'
pvrusb2-hdw.c:(.text+0xccc83): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `pvr2_hdw_remove_usb_stuff.part.25':
pvrusb2-hdw.c:(.text+0xcd3f9): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd405): undefined reference to `usb_free_urb'
pvrusb2-hdw.c:(.text+0xcd421): undefined reference to `usb_kill_urb'
pvrusb2-hdw.c:(.text+0xcd42d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd658): undefined reference to `usb_lock_device_for_reset'
drivers/built-in.o: In function `pvr2_hdw_device_reset':
(.text+0xcd664): undefined reference to `usb_reset_device'
drivers/built-in.o: In function `pvr2_hdw_cpureset_assert':
(.text+0xcd6f9): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_hdw_cpufw_set_enabled':
(.text+0xcd84e): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware1':
pvrusb2-hdw.c:(.text+0xcda47): undefined reference to `usb_clear_halt'
pvrusb2-hdw.c:(.text+0xcdb04): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `pvr2_upload_firmware2':
(.text+0xce7dc): undefined reference to `usb_bulk_msg'
drivers/built-in.o: In function `pvr2_stream_buffer_count':
pvrusb2-io.c:(.text+0xd2e05): undefined reference to `usb_alloc_urb'
pvrusb2-io.c:(.text+0xd2e5b): undefined reference to `usb_kill_urb'
pvrusb2-io.c:(.text+0xd2e9f): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `pvr2_stream_internal_flush':
pvrusb2-io.c:(.text+0xd2f9b): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd3328): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `pvr2_buffer_queue':
(.text+0xd33ea): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_read_reg':
(.text+0xd3efa): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stk1160_write_reg':
(.text+0xd3f4f): undefined reference to `usb_control_msg'
drivers/built-in.o: In function `stop_streaming':
stk1160-v4l.c:(.text+0xd4997): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `start_streaming':
stk1160-v4l.c:(.text+0xd4a9f): undefined reference to `usb_set_interface'
stk1160-v4l.c:(.text+0xd4afa): undefined reference to `usb_submit_urb'
stk1160-v4l.c:(.text+0xd4ba3): undefined reference to `usb_set_interface'
drivers/built-in.o: In function `stk1160_isoc_irq':
stk1160-video.c:(.text+0xd509b): undefined reference to `usb_submit_urb'
drivers/built-in.o: In function `stk1160_cancel_isoc':
(.text+0xd50ef): undefined reference to `usb_kill_urb'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd5155): undefined reference to `usb_free_coherent'
drivers/built-in.o: In function `stk1160_free_isoc':
(.text+0xd515d): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd5278): undefined reference to `usb_alloc_urb'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd52c2): undefined reference to `usb_alloc_coherent'
drivers/built-in.o: In function `stk1160_alloc_isoc':
(.text+0xd53c4): undefined reference to `usb_free_urb'
drivers/built-in.o: In function `zr364xx_driver_init':
zr364xx.c:(.init.text+0x463e): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `pvr_init':
pvrusb2-main.c:(.init.text+0x4662): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `stk1160_usb_driver_init':
stk1160-core.c:(.init.text+0x467d): undefined reference to `usb_register_driver'
drivers/built-in.o: In function `zr364xx_driver_exit':
zr364xx.c:(.exit.text+0x1377): undefined reference to `usb_deregister'
drivers/built-in.o: In function `pvr_exit':
pvrusb2-main.c:(.exit.text+0x1389): undefined reference to `usb_deregister'
drivers/built-in.o: In function `stk1160_usb_driver_exit':
stk1160-core.c:(.exit.text+0x13a0): undefined reference to `usb_deregister'

Suggested-by: "Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7115: Add register setup and config for gm7113c

The gm7113c chip is similar to the original saa7113 chip, so I try to
re-use most of the saa7113 specific setup-/configuration registers.
According to the datasheet, the gm7113c chip has not implemented
any register-addresses after 0x1f, so I add a new entry to for the chip
to the saa711x_has_reg function.
The devices I've seen using this chip will fail to get stable video-sync
if these registers are not zeroed:
R_14_ANAL_ADC_COMPAT_CNTL
R_15_VGATE_START_FID_CHG
R_16_VGATE_STOP
R_17_MISC_VGATE_CONF_AND_MSB
The saa711x_set_v4lstd is updated to send a simpler configuration-table
to avoid setting these registers.

Signed-off-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7115: add detection code for gm7113c

Adds a code that (auto)detects gm7113c clones. The auto-detection
here is not perfect, as, on contrary to what it would be expected
by looking into its datasheets some devices would return, instead:
saa7115 0-0025: chip 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 @ 0x4a is unknown
(found on a device labeled as GM7113C 1145 by Ezequiel Garcia)

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7115: move the autodetection code out of the probe function

As we're now seeing other variants from chinese clones, like
gm1113c, we'll need to add more bits at the detection code.
So, move it into a separate function.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested-by: Jon Arne Jørgensen <jonarne@jonarne.no>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] wl128x: do not call copy_to_user() while holding spinlocks

copy_to_user() must not be called with spinlocks held, but it is in
fmc_transfer_rds_from_internal_buff().
The patch copies data to tmpbuf, releases spinlock and then passes it to userspace.
By the way there is a small unification: replace a couple of hardcoded constants by a macro.
Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] solo6x10: Approximate frame intervals with non-standard denominator

Instead of falling back to 1/25 (PAL) or 1/30 (NTSC).

Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: tvp7002: enable TVP7002 decoder for media controller based usage

This patch enables tvp7002 decoder driver for media controller
based usage by adding v4l2_subdev_pad_ops  operations support
for enum_mbus_code, set_pad_format, get_pad_format and media_entity_init()
on probe and media_entity_cleanup() on remove.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] hdpvr: Added some error handling in hdpvr_start_streaming()

Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] hdpvr: Removed unnecessary get_video_info() call from hdpvr_device_init()

Signed-off-by: Leonid Kegulskiy <leo@lumanate.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpbe: fix checkpatch warning for CamelCase

This patch fixes checkpatch warning to avoid CamelCase.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: Add support for 1b80:e1cc Delock 61959

Hardware is the same as MaxMedia UB425-TC but ships with a different
remote.

Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: Add rc-delock-61959

This adds the keytable for the remote that comes with the Delock 61959.
NEC protocol with address 0x866b.

Signed-off-by: Jakob Haufe <sur5r@sur5r.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] update saa7134 and tuner cardlists

Those are automatically updated using the cardlist script.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] CARDLIST.bttv: add new cards

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpif_display: move displaying of error to approppraite place

this patch moves the displaying out error case  "VPIF IRQ request failed\n"
when there is actual request_irq() fail.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: davinci: vpif: remove unwanted header file inclusion

this patch removes unwanted header file inclusion and sorts
header alphabetically.

Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videodev2.h: Make V4L2_PIX_FMT_MPEG4 comment more specific about its usage

Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: Add CyberVision CV06

Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: Add noname Bt848 capture card with 14MHz xtal

Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.

[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media:adv7180: Use dev_pm_ops

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bfin_capture: add query_dv_timings/enum_dv_timings support

More dv_timings ioctl ops are introduced in video core.
Add query_dv_timings/enum_dv_timings accordingly.

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] blackfin: add display support in ppi driver

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] bttv: Add Adlink MPG24 entry to the bttv cardlist

Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
Hans

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5k6aa: Convert to devm_gpio_request_one()

Use the devm_gpio_request_one() managed function to simplify cleanup
code paths.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] s5c73m3: Convert to devm_gpio_request_one()

Use the devm_gpio_request_one() managed function to simplify cleanup
code paths.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] m5mols: Convert to devm_request_irq()

Using the managed function the free_irq() calls can be removed from the
probe error path and the remove handler.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: Convert to devm_regulator_bulk_get()

Using the managed function the regulator_bulk_put() calls can be removed
from the probe error path and the remove handler.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: Convert to devm_gpio_request_one()

Using the managed function the gpio_free() calls can be removed from the
probe error path and the remove handler.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: Convert to devm_kzalloc()

Using the managed function the kfree() calls can be removed from the
probe error path and the remove handler.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: i2c: Convert to gpio_request_one()

Replace gpio_request() with gpio_request_one() and remove the associated
gpio_direction_output() calls.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tvp514x: Fix double free

The tvp514x data structure is allocated using devm_kzalloc(). Freeing it
explictly would result in a double free. Fix it.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v032: Free control handler in cleanup paths

The control handler must be freed in the probe error path and in the
remove handler.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Use gpio_is_valid()

Replace the manual validity checks for the reset GPIO with the
gpio_is_valid() function.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9p031: Power down the sensor if no supported device has been detected

The mt9p031 driver first accesses the I2C device in its .registered()
method. While doing that it first powers the device up, but if probing
fails, it doesn't power the chip back down. This patch fixes that bug.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Merge tag 'v3.10-rc1' into patchwork

Linux 3.10-rc1

* tag 'v3.10-rc1': (11697 commits)
  Linux 3.10-rc1
  [SCSI] qla2xxx: Update firmware link in Kconfig file.
  [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
  [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
  [SCSI] pm80xx: thermal, sas controller config and error handling update
  [SCSI] pm80xx: NCQ error handling changes
  [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
  [SCSI] pm80xx: Changed module name and debug messages update
  [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
  [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
  [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
  [SCSI] pm80xx: MSI-X implementation for using 64 interrupts
  [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
  [SCSI] pm80xx: Multiple inbound/outbound queue configuration
  [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
  [SCSI] lpfc: fix up Kconfig dependencies
  [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
  dm cache: set config value
  dm cache: move config fns
  dm thin: generate event when metadata threshold passed
  ...

Linux 3.10-rc1

Merge tag 'trace-fixes-v3.10' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing/kprobes update from Steven Rostedt:
 "The majority of these changes are from Masami Hiramatsu bringing
  kprobes up to par with the latest changes to ftrace (multi buffering
  and the new function probes).

  He also discovered and fixed some bugs in doing so.  When pulling in
  his patches, I also found a few minor bugs as well and fixed them.

  This also includes a compile fix for some archs that select the ring
  buffer but not tracing.

  I based this off of the last patch you took from me that fixed the
  merge conflict error, as that was the commit that had all the changes
  I needed for this set of changes."

* tag 'trace-fixes-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing/kprobes: Support soft-mode disabling
  tracing/kprobes: Support ftrace_event_file base multibuffer
  tracing/kprobes: Pass trace_probe directly from dispatcher
  tracing/kprobes: Increment probe hit-count even if it is used by perf
  tracing/kprobes: Use bool for retprobe checker
  ftrace: Fix function probe when more than one probe is added
  ftrace: Fix the output of enabled_functions debug file
  ftrace: Fix locking in register_ftrace_function_probe()
  tracing: Add helper function trace_create_new_event() to remove duplicate code
  tracing: Modify soft-mode only if there's no other referrer
  tracing: Indicate enabled soft-mode in enable file
  tracing/kprobes: Fix to increment return event probe hit-count
  ftrace: Cleanup regex_lock and ftrace_lock around hash updating
  ftrace, kprobes: Fix a deadlock on ftrace_regex_lock
  ftrace: Have ftrace_regex_write() return either read or error
  tracing: Return error if register_ftrace_function_probe() fails for event_enable_func()
  tracing: Don't succeed if event_enable_func did not register anything
  ring-buffer: Select IRQ_WORK

Merge tag 'stable/for-linus-3.10-rc0-tag-two' of git://git./linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 - More fixes in the vCPU PVHVM hotplug path.
 - Add more documentation.
 - Fix various ARM related issues in the Xen generic drivers.
 - Updates in the xen-pciback driver per Bjorn's updates.
 - Mask the x2APIC feature for PV guests.

* tag 'stable/for-linus-3.10-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/pci: Used cached MSI-X capability offset
  xen/pci: Use PCI_MSIX_TABLE_BIR, not PCI_MSIX_FLAGS_BIRMASK
  xen: clear IRQ_NOAUTOEN and IRQ_NOREQUEST
  xen: mask x2APIC feature in PV
  xen: SWIOTLB is only used on x86
  xen/spinlock: Fix check from greater than to be also be greater or equal to.
  xen/smp/pvhvm: Don't point per_cpu(xen_vpcu, 33 and larger) to shared_info
  xen/vcpu: Document the xen_vcpu_info and xen_vcpu
  xen/vcpu/pvhvm: Fix vcpu hotplugging hanging.

Merge tag 'scsi-for-linus' of git://git./linux/kernel/git/jejb/scsi

Pull second SCSI update from James "Jaj B" Bottomley:
 "This is the final round of SCSI patches for the merge window.  It
  consists mostly of driver updates (bnx2fc, ibmfc, fnic, lpfc,
  be2iscsi, pm80xx, qla4x and ipr).

  There's also the power management updates that complete the patches in
  Jens' tree, an iscsi refcounting problem fix from the last pull, some
  dif handling in scsi_debug fixes, a few nice code cleanups and an
  error handling busy bug fix."

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (92 commits)
  [SCSI] qla2xxx: Update firmware link in Kconfig file.
  [SCSI] iscsi class, qla4xxx: fix sess/conn refcounting when find fns are used
  [SCSI] sas: unify the pointlessly separated enums sas_dev_type and sas_device_type
  [SCSI] pm80xx: thermal, sas controller config and error handling update
  [SCSI] pm80xx: NCQ error handling changes
  [SCSI] pm80xx: WWN Modification for PM8081/88/89 controllers
  [SCSI] pm80xx: Changed module name and debug messages update
  [SCSI] pm80xx: Firmware flash memory free fix, with addition of new memory region for it
  [SCSI] pm80xx: SPC new firmware changes for device id 0x8081 alone
  [SCSI] pm80xx: Added SPCv/ve specific hardware functionalities and relevant changes in common files
  [SCSI] pm80xx: MSI-X implementation for using 64 interrupts
  [SCSI] pm80xx: Updated common functions common for SPC and SPCv/ve
  [SCSI] pm80xx: Multiple inbound/outbound queue configuration
  [SCSI] pm80xx: Added SPCv/ve specific ids, variables and modify for SPC
  [SCSI] lpfc: fix up Kconfig dependencies
  [SCSI] Handle MLQUEUE busy response in scsi_send_eh_cmnd
  [SCSI] sd: change to auto suspend mode
  [SCSI] sd: use REQ_PM in sd's runtime suspend operation
  [SCSI] qla4xxx: Fix iocb_cnt calculation in qla4xxx_send_mbox_iocb()
  [SCSI] ufs: Correct the expected data transfersize
  ...

Merge branch 'release' of git://git./linux/kernel/git/lenb/linux

Pull idle update from Len Brown:
 "Add support for new Haswell-ULT CPU idle power states"

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  intel_idle: initial C8, C9, C10 support
  tools/power turbostat: display C8, C9, C10 residency