wifi: iwlwifi: api: remove unused commands

Some commands are no longer used and have broken kernel-doc links,
so just remove them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.3dad4ad9b53e.I018abd02d6925950b8748dfb7a59db87255fc670@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: api: use __le16 instead of u16

Even for reserved values we shouldn't use u16, that's just
error prone. Fix this to __le16.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.29ebf70aa64e.I1263f6724e1c70ff5541f447b9744f143ee736a3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: api: link context action in kernel-doc

This is clearer in kernel-doc than spelling out the prefix.
It also lets us generate better tracing data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.e11ece794f60.I9874c7b0437071a2620d68ca5a16efed60da07a9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: tell firmware about per-STA MFP enablement

Indicate to the firmware for each station whether or not MFP
is used with this station. Note that we indicate MFP for it
before authorized since we don't know yet, and that will make
the firmware not handle should-be-protected management frames
without being able to check them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601095201.b1052f39af4c.I1b46b751d5808e65ea3d0e7b8b38209c5aecf042@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: send time sync only if needed

If there's no peer configured then there's no point in sending
the command down to the firmware with an invalid peer address.

Fixes: cf85123a210f ("wifi: iwlwifi: mvm: support enabling and disabling HW timestamping")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.0fb9f81f1852.Idcc41b67d1fbb421e5ed9bac2177b948b7b4d1c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: remove warning for beacon filtering error

This warning is sometimes happening if we force a FW error
while disconnecting, which is annoying but harmless.

However, it's also pointless to throw a warning here, since
the stack and driver state doesn't really help, so just
remove that so the driver will ignore the error if any.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.29fe6990d372.I00ff5dc7bfb4025a609f380a0a3911d842b72449@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: remove dead code in iwl_dump_ini_imr_get_size()

Remove the check for the IMR debug data size which
leads to dead code.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.58eec8d40729.Ifb7d64706eed45726db804f36e785283dff7adab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Add Dell to ppag approved list

Add 2 new entries for Dell in PPAG approved list.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.a2696f0538ef.I324e4a0cc4696c27830a490b79c42dfeff8ba074@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: FTM initiator MLO support

When checking if the initiator is associated to the responder,
iterate over all active links.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.a0d86655e7d2.I8f140ca55094da1d73c387fc036394fb2c148c85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: pcie: adjust Bz device timings

The 100ms shouldn't be needed, only 10ms. However after
reset we should have 10ms as well for these devices.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.9a5627c1ff18.Ifcfbccd5458bd9ebd496aa834284fb0facfcaaef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: offload BTM response during D3

There are mainly two types of BTM (BSS Transition Management)
requests, recommendations and notifications. For the first type,
a response is needed otherwise, most probably the STA will be
disconnected.
Since we don't want to wake up the host on it, set the BTM to reject
offload flag (if the device supports it) and rely on the FW to take
care of it. The FW will reject the BTM request and in case the AP
sends DEAUTH the FW can wake up the host to let it decide on the
next steps.

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.d95ae6f2804c.I9457acc55bc23ce715c714b5088058f52540c224@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: do not log undefined DRAM buffers unnecessarily

DRAM buffers that are not defined in the TLVs (or are unused in the
preset) would cause a log message. To avoid confusion, skip processing
buffers with an invalid (i.e. uninitialized) DRAM path.

This further reduces the noise of the message in cases where it is
unlikely to be helpful. Also update a related debug log string to better
describe what is happening.

Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.ecae60cf2d7f.Ib44a94d4aeb55dbb2e52edea8b69a09bc0f722c3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: acpi: add other Google OEMs to the ppag approved list

Add two new vendors to the PPAG approved vendor list
as Google OEMs.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.b89a3f9e3ae0.Iab1e13285c58ef1fee2a8bad8429eda4547b0b74@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: clarify EHT RU allocation bits

Calling this IWL_RX_PHY_DATA1_EHT_B0 is just confusing,
it's the RU allocation bit 0. Also then align the name
for B1-B7 accordingly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.824edb28c0eb.Ia9f74573e3ac771911b679558984f1bfb36de674@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: support injection rate control

Supporting controlling the frame rate during injection,
HT/VHT are supported in addition to legacy rates.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.85a662792649.I0847b47dec0dfb0290d7b15ebc6bc0a575eed7b5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Add vendors to TAS approved list

Allows vendors to use the time average sar feature.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.845c205e4def.Iab5c849617ed7e13304e4dfc7def668659439946@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: iwlmei: fix compilation error

The feature is still disabled (depends on BROKEN), but
the code had a compilation error after one of the merges.
Fix that.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531085033.216028-1-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: update response for mcc_update command

Add support for the MCC update response version 8.
Versions 5-6 are already covered by the existing
flags conversion, and 7 isn't used.

The capabilities field in iwl_mcc_update_resp is 32 bits
wide now, and the flags moved, so some more changes are
needed.

While at it, convert the flags to bool (to avoid having
to deal with BIT(16) specially etc.) and use the
struct_size() macro for the memory allocation.

Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.fd9016f8f994.Ibddcb9fbfa74895f742c0ac20968720691c94853@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: support PPAG in China for older FW cmd version

Allows the China bit in the ppag flags to turn on also when
FW cmd version is 1 (if FW has the capability).

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.3cc19e799eeb.I9054b1d63fd7ae2b5f0e416825b4b1dc9f79cc80@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: remove useless code

Setting the station to -EBUSY was originally done under
this lock, and the comment still refers to it. But this
no longer happens because that was removed when DQA was
removed. Remove the leftover code as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.30048b1cd0fd.Ie2c2ff6fd7c6e3ebf5b736de350dc15515970792@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: disable RX STBC when a device doesn't support it

Some devices, like step A0 of GL FM device doesn't support RX STBC
for VHT/HE. Add a workaround to remove it from capabilities in
this case.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.65c3e09813e5.Iadfd8cdb0ea5a8088ae3daa555c780c423951894@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: fw: Add new ODM vendor to ppag approved list

Add new oem/odm pair to ppag approved vendors list
when specified by platform.

Signed-off-by: Ariel Malamud <ariel.malamud@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.549a57a1cf11.I7392b1cd31f4f7ee60aafe2093f4e82b1d6fd3a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: adjust csa notifications and commands to MLO

In the following notifications and commands mac_id was replaced
with link_id:
* CANCEL_CHANNEL_SWITCH_CMD
* CHANNEL_SWITCH_START_NOTIF
* CHANNEL_SWITCH_ERROR_NOTIF

The logic around was not changed, so only adjust handling
mac/link id.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.6aa6e394f5fe.Ie9e78918511ca901f9f3966d774fa74a71a186e3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: update the FW apis for LINK and MAC commands

The firmware added new fields to be able to pass the link_id as the AP
knows it and the esr_transition_timeout.
For now, pass only the link_id since we don't have access to the
esr_transition_timeout yet.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.bf80ce717458.Icd4174911227c00cd12783fe1f517ae8097809b9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: Make iwl_mvm_diversity_iter() MLO aware

This function is MLO related, so it should iterate over all the links,
and not only on deflink.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.56a9c709e987.I9716195ec288cce2c929338c254ee9add8cfcc1f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: don't silently ignore missing suspend or resume ops

In case the driver doesn't implement suspend or resume operations
on the transport layer, notify the driver's upper layer.
Otherwise, we might access d3_status uninitialized.

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.0c55e0ca92f1.I6870fe1683215e65d3d036f9b576b03b7b7257be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: support PASN for MLO

When adding a PASN station, the non MLD API was used. This results
in assert when operating as MLD. Fix it to use the MLD API when
operating as MLD. For now, the default link is used for the added
station.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.7c35dccc8a12.I7bc78cd16d7c750f42fdd60e07e839a860d279d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: dissolve iwl_mvm_mac_add_interface_common()

This wasn't really common anymore, so dissolve it, it has a
pretty strange calling convention that's confusing.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.44320ab2e842.Ie1d6b9c28caca3b541ca383a4c0c8799b0e72fe0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: make internal callback structs const

There's no need for these to be writable, so they can
be const (and static).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.c41eb6687868.I2dac1158e5723187bda1973aa49fde8a794621c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: use link ID in missed beacon notification

This new version of missed beacon notification uses link_id
instead of mac_id. Also add an option to use link id for
retrieving vif.

Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.17fe1cc632f1.Id1fabb532e2174712fe17d4ad86a2c8c64ae84da@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: cfg: freeze 22500 devices FW API

FW version is now frozen for 22500 devices. Don't
allow newer versions in the driver.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.8a25ebf9134c.I3f1454498322ce28cb687d28c091c7ee092cefca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: brcmutil: use helper function pktq_empty() instead of open code

pktq_empty was added in commit 5b435de0d786 ("net: wireless: add brcm80211
drivers") but it is currently not being utilized in some areas. This commit
replaces the open code with the pktq_empty() function.

Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527114954.3281-2-claudiajkang@gmail.com

wifi: rtlwifi: use helper function rtl_get_hdr()

Although rtl_get_hdr was added in commit 3dad618b7b92 ("rtlwifi: Change
wifi.h for rtl8192se and rtl8192de"), it is currently not being utilized
in some areas. This commit replaces the open code with the rtl_get_hdr()
function.

Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527114954.3281-1-claudiajkang@gmail.com

wifi: rtw88: usb: silence log flooding error message

When receiving more rx packets than the kernel can handle the driver
drops the packets and issues an error message. This is bad for two
reasons. The logs are flooded with myriads of messages, but then time
consumed for printing messages in that critical code path brings down
the device. After some time of excessive rx load the driver responds
with:

rtw_8822cu 1-1:1.2: failed to get tx report from firmware
rtw_8822cu 1-1:1.2: firmware failed to report density after scan
rtw_8822cu 1-1:1.2: firmware failed to report density after scan

The device stops working until being replugged.

Fix this by lowering the priority to debug level and also by
ratelimiting it.

Fixes: a82dfd33d1237 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230524103934.1019096-1-s.hauer@pengutronix.de

wifi: ray_cs: add sanity check on local->sram/rmem/amem

The ray_config uses ray_release as its unified error handling function.
However, it does not know if local->sram/rmem/amem succeeds or not.

Fix this by adding sanity check on local->sram/rmem/amem in the
ray_relase.

Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316133236.556198-3-dzm91@hust.edu.cn

wifi: ray_cs: remove one redundant del_timer

In ray_detach, it and its child function ray_release both call
del_timer(_sync) on the same timer.

Fix this by removing the del_timer_sync in the ray_detach, and revising
the del_timer to del_timer_sync.

Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316133236.556198-2-dzm91@hust.edu.cn

wifi: ray_cs: Fix an error handling path in ray_probe()

Should ray_config() fail, some resources need to be released as already
done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
ray_probe(), not ray_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/8c544d18084f8b37dd108e844f7e79e85ff708ff.1684570373.git.christophe.jaillet@wanadoo.fr

wifi: wl3501_cs: Fix an error handling path in wl3501_probe()

Should wl3501_config() fail, some resources need to be released as already
done in the remove function.

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7cc9c9316489b7d69b36aeb0edd3123538500b41.1684569865.git.christophe.jaillet@wanadoo.fr

wifi: atmel: Fix an error handling path in atmel_probe()

Should atmel_config() fail, some resources need to be released as already
done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
atmel_probe(), not atmel_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1e65f174607a83348034197fa7d603bab10ba4a9.1684569156.git.christophe.jaillet@wanadoo.fr

wifi: orinoco: Fix an error handling path in orinoco_cs_probe()

Should orinoco_cs_config() fail, some resources need to be released as
already done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
orinoco_cs_probe(), not orinoco_cs_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e24735ce4d82901d5f7ea08419eea53bfdde3d65.1684568286.git.christophe.jaillet@wanadoo.fr

wifi: orinoco: Fix an error handling path in spectrum_cs_probe()

Should spectrum_cs_config() fail, some resources need to be released as
already done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
spectrum_cs_probe(), not spectrum_cs_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/c0bc0c21c58ca477fc5521607615bafbf2aef8eb.1684567733.git.christophe.jaillet@wanadoo.fr

wifi: rtw89: use flexible array member in rtw89_btc_btf_tlv

struct rtw89_btc_btf_tlv contains a one-byte member that is intended as a
flexible array:

In function 'fortify_memcpy_chk',
    inlined from '_append_tdma' at drivers/net/wireless/realtek/rtw89/coex.c:1579:3:
include/linux/fortify-string.h:583:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
  583 |                         __write_overflow_field(p_size_field, size);
      |                         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Make this actually use a flexible array to let the compiler understand.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230523113241.2772811-1-arnd@kernel.org

wifi: rtw89: 8851b: rfk: Fix spelling mistake KIP_RESOTRE -> KIP_RESTORE

There is a spelling mistake in a literal string. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522085924.913649-1-colin.i.king@gmail.com

wifi: rtw89: use struct to access register-based H2C/C2H

The register-based H2C/C2H are used to exchange commands and events with
firmware. The exchange data is limited, but it is relatively simple,
because it can work before HCI initialization. To make these code clean,
use struct to access them. This patch doesn't change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-6-pkshih@realtek.com

wifi: rtw89: use struct and le32_get_bits() to access RX descriptor

RX descriptor is to provide basic and important information related to
packets, such as packet size, security, MAC ID and so on. Change to use
struct to access these fields, and not change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-5-pkshih@realtek.com

wifi: rtw89: use struct and le32_get_bits() to access received PHY status IEs

PHY status IEs generated by BB hardware is to provide more detail
information related to received packets, such as RSSI and bandwidth.

To avoid type casting, change buf type from u8* to void* as well.

This patch doesn't change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-4-pkshih@realtek.com

wifi: rtw89: use struct and le32_get_bits to access RX info

If received packet type is PPDU status, RX info provides information
attached by MAC hardware, and mention how long BB information attached.

This conversion patch doesn't change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-3-pkshih@realtek.com

wifi: rtw89: add chip_ops::query_rxdesc() and rxd_len as helpers to support newer chips

The next generation chips use different RX descriptor format, so add
a chip_ops to hook suitable handlers. Also, the length of RX descriptor is
different, so add a variable to store the length according to chip and
descriptor content dynamically. Then, the code can be more general.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-2-pkshih@realtek.com

wifi: rtw89: 8851b: add 8851be to Makefile and Kconfig

Since 8851BE is ready, so add 8851BE to Makefile and Kconfig. Currently,
it can support STA, AP and monitor modes with good performance.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-8-pkshih@realtek.com

wifi: rtw89: add tx_wake notify for 8851B

8851B has the same issue: management frames get stuck when WiFi
chip enters low PS mode, so we also add notify wake function to
trigger WiFi chip wake before forwarding management frames.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-7-pkshih@realtek.com

wifi: rtw89: enlarge supported length of read_reg debugfs entry

The register ranges of upcoming chips are different from current, and even
existing chips have different ranges, so support longer length to dump
registers. Then, user space can decide the ranges according to chip.

Since arbitrary length (e.g. 7) would be a little complicated, so simply
make length a multiple of 16. The output looks like

18620000h : 8580801f 82828282 82828282 080800fd

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-6-pkshih@realtek.com

wifi: rtw89: 8851b: add RF configurations

RF configurations include RF calibrations and getting thermal value.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-5-pkshih@realtek.com

wifi: rtw89: 8851b: add MAC configurations to chip_info

These configurations include path control, TX grant, TX scheduler,
register-based H2C/C2H and so on.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-4-pkshih@realtek.com

wifi: rtw89: 8851b: fill BB related capabilities to chip_info

These capabilities include helpers of BT coexistence, RX PPDU status
parser, DIG (dynamic initial gain) and CFO (center frequency offset)
settings.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-3-pkshih@realtek.com

wifi: rtw89: 8851b: add TX power related functions

Get TX power value from tables according to selected country and channel,
and set proper power to registers.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-2-pkshih@realtek.com

wifi: rtw89: refine packet offload handling under SER

H2C of packet offload needs to wait FW ACK by C2H. But, it's possible
that packet offload happens during SER (system error recovery), e.g.
SER L2 which restarts HW. More, packet offload flow isn't deferrable.
So, the H2C wait may get `ret == 1` (unreachable).

However, the logic FW deals with packet offload is simple enough, just
clone content. It means that as long as the H2C is issued successfully,
the thing will succeed sooner or later. Therefore, after we add a debug
log when receiving ACK to packet offload, it would be acceptable that
during SER, packet offload don't really wait for ACK. And, if debugging,
we can still check its debug logs. Besides, we can expect that if we see
SER before receiving ACK to packet offload, those debug logs of the ACK
have a time difference.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-4-pkshih@realtek.com

wifi: rtw89: tweak H2C TX waiting function for SER

Some specific H2C (host to chip command) needs waiting until FW ACK by
C2H (chip to host event). However, during SER (system error recovery),
most interrupts are disabled, so we can't receive C2H immediately. It
causes this kind of H2C TX waits will always time out during SER.

To save time spent by SER, we don't do these redundant waits. And, to
make a difference from -ETIMEDOUT in other cases, we make the function
return 1 for SER case. When some H2C callers really catch `ret == 1` at
runtime, they can determine whether it's reasonable or not, and consider
how to resolve their flow if needed.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-3-pkshih@realtek.com

wifi: rtw89: ser: reset total_sta_assoc and tdls_peer when L2

The total_sta_assoc and the tdls_peer are used for statistics accodring
to stations' information. L2 (Level 2) SER (system error recovery) will
call ieee80211_restart_hw() which re-invokes sta_state ops. And then,
the total_sta_assoc and tdls_peer will be re-increased. In case wrong
statistics results, we reset them in SER L2 handling.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-2-pkshih@realtek.com

wifi: rtw88: Add support for the SDIO based RTL8723DS chipset

Wire up RTL8723DS chipset support using the rtw88 SDIO HCI code as well
as the existing RTL8723D chipset code.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-5-martin.blumenstingl@googlemail.com

mmc: sdio: Add/rename SDIO ID of the RTL8723DS SDIO wifi cards

RTL8723DS comes in two variant and each of them has their own SDIO ID:
- 0xd723 can connect two antennas. The WiFi part is still 1x1 so the
  second antenna can be dedicated to Bluetooth
- 0xd724 can only connect one antenna so it's shared between WiFi and
  Bluetooth

Add a new entry for the single antenna RTL8723DS (0xd724) which can be
found on the MangoPi MQ-Quad. Also rename the existing RTL8723DS entry
(0xd723) so it's name reflects that it's the variant with support for
two antennas.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-4-martin.blumenstingl@googlemail.com

wifi: rtw88: rtw8723d: Implement RTL8723DS (SDIO) efuse parsing

The efuse of the SDIO RTL8723DS chip has only one known member: the mac
address is at offset 0x11a. Add a struct rtw8723ds_efuse describing this
and use it for copying the mac address when the SDIO bus is used.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-3-martin.blumenstingl@googlemail.com

wifi: rtw88: sdio: Check the HISR RX_REQUEST bit in rtw_sdio_rx_isr()

rtw_sdio_rx_isr() is responsible for receiving data from the wifi chip
and is called from the SDIO interrupt handler when the interrupt status
register (HISR) has the RX_REQUEST bit set. After the first batch of
data has been processed by the driver the wifi chip may have more data
ready to be read, which is managed by a loop in rtw_sdio_rx_isr().

It turns out that there are cases where the RX buffer length (from the
REG_SDIO_RX0_REQ_LEN register) does not match the data we receive. The
following two cases were observed with a RTL8723DS card:
- RX length is smaller than the total packet length including overhead
  and actual data bytes (whose length is part of the buffer we read from
  the wifi chip and is stored in rtw_rx_pkt_stat.pkt_len). This can
  result in errors like:
    skbuff: skb_over_panic: text:ffff8000011924ac len:3341 put:3341
  (one case observed was: RX buffer length = 1536 bytes but
   rtw_rx_pkt_stat.pkt_len = 1546 bytes, this is not valid as it means
   we need to read beyond the end of the buffer)
- RX length looks valid but rtw_rx_pkt_stat.pkt_len is zero

Check if the RX_REQUEST is set in the HISR register for each iteration
inside rtw_sdio_rx_isr(). This mimics what the RTL8723DS vendor driver
does and makes the driver only read more data if the RX_REQUEST bit is
set (which seems to be a way for the card's hardware or firmware to
tell the host that data is ready to be processed).

For RTW_WCPU_11AC chips this check is not needed. The RTL8822BS vendor
driver for example states that this check is unnecessary (but still uses
it) and the RTL8822CS drops this check entirely.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-2-martin.blumenstingl@googlemail.com

wifi: add HAS_IOPORT dependencies

In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.

Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522105049.1467313-44-schnelle@linux.ibm.com

Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git

ath.git patches for v6.5. Major changes:

ath11k

* Multiple Basic Service Set Identifier (MBSSID) and Enhanced MBSSID
  Advertisement (EMA) support in AP mode

wifi: ath11k: Send HT fixed rate in WMI peer fixed param

Due to the firmware behavior with HT fixed rate setting,
HT fixed rate MCS with NSS > 1 are treated as NSS = 1
HT rates in the firmware and enables the HT fixed rate of
NSS = 1.

This leads to HT fixed rate is always configured for NSS = 1
even though the user sets NSS = 2 or > 1 HT fixed MCS in the
set bitrate command.

Currently HT fixed MCS is sent via WMI peer assoc command.
Fix this issue, by sending the HT fixed rate MCS in WMI peer
fixed param instead of sending in peer assoc command.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230504092033.3542456-3-quic_mkenna@quicinc.com

wifi: ath11k: Relocate the func ath11k_mac_bitrate_mask_num_ht_rates() and change hweight16 to hweight8

Relocate the function ath11k_mac_bitrate_mask_num_ht_rates() definition
to call this function from other functions which helps to avoid the
compilation error (function not defined).

ht_mcs[] is 1 byte array and it is enough to use hweight8() instead
of hweight16(). Hence, fixed the same.

Tested on: Compile tested only.

Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230504092033.3542456-2-quic_mkenna@quicinc.com

wifi: ath12k: increase vdev setup timeout

When vdev start/stop happens, response from firmware is received with delay
and hence there is a timeout before VDEV can be up/down.
Also, with maximum peers connected and when vdev stop occurs, firmware
will take time to clean up all the peers and vap queues.
In such cases as well, vdev start/stop response is sent by firmware with delay.

Increase the vdev setup timeout as recommended by firmware team.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1

Signed-off-by: Aishwarya R <quic_aisr@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230428091041.20033-1-quic_rgnanase@quicinc.com

wifi: rtw89: 8851b: rfk: add TSSI

TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.

When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.

To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com

wifi: rtw89: 8851b: rfk: add DPK

DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.

Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com

wifi: rtw89: 8851b: rfk: add RX DCK

RX DCK is receiver DC calibration. With this calibration, we have proper
DC offset to reflect correct received signal strength indicator. Do this
calibration when bringing up interface and going to run on AP channel.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-2-pkshih@realtek.com

wifi: rtw89: 8851b: add to parse efuse content

Parse efuse content to recognize MAC address, RFE type, XTAL offset and
so on. And, parse offset of PHY capability to retrieve TX power
calibration data.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-7-pkshih@realtek.com

wifi: rtw89: 8851b: add set channel function

Set MAC/BB/RF registers according to channel we are going to set. In
additional, certain channels or bands need more deals, such as enable CCK
in 2 GHz band, spur elimination at certain frequencies.

The set channel helper is used to save/restore states before/after setting
channel, and does reset BB to prevent hardware getting stuck in abnormal
state during switching channel and receiving data.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-6-pkshih@realtek.com

wifi: rtw89: 8851b: add basic power on function

Add basic functions to power on chip and enable and access BB/RF, as
well as reset and hardware settings of BB.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-5-pkshih@realtek.com

wifi: rtw89: 8851b: add BT coexistence support function

Add 8851B specific parameters of BT coexistence. Since 8851B has special
two antenna hardware module with antenna diversity, BT coexistence needs
to recognize this, so add some fields to store these information for
further use.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-4-pkshih@realtek.com

wifi: rtw89: 8851b: configure GPIO according to RFE type

Though 8851BE is a 1x1 chip, but it has two antenna hardware module that
needs additional configuration to help choose antenna we are going to use.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-3-pkshih@realtek.com

wifi: rtw89: 8851b: add to read efuse version to recognize hardware version B

8851B hardware version A and B use different firmware, but register version
code of these two are the same, so add this helper to read efuse version to
determine which version is installed.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-2-pkshih@realtek.com

wifi: rtl8xxxu: Rename some registers

Give proper names:

RF6052_REG_UNKNOWN_56 -> RF6052_REG_PAD_TXG
RF6052_REG_UNKNOWN_DF -> RF6052_REG_GAIN_CCA

And fix typos:

REG_OFDM0_AGCR_SSI_TABLE -> REG_OFDM0_AGC_RSSI_TABLE
REG_BB_ACCEESS_CTRL -> REG_BB_ACCESS_CTRL

Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/40157253-76bd-8b23-06e0-3365139b5395@gmail.com

wifi: rtl8xxxu: Support new chip RTL8192FU

This is a newer chip, similar to the RTL8710BU in that it uses the same
PHY status structs.

Features: 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps.

It can allegedly have Bluetooth, but that's not implemented here.

This chip can have many RFE (RF front end) types, of which types 1
and 5 are the only ones tested. Many of the other types need different
initialisation tables. They can be added if someone wants them.

The vendor driver v5.8.6.2_35538.20191028_COEX20190910-0d02 from
https://github.com/BrightX/rtl8192fu was used as reference, with
additional device IDs taken from
https://github.com/kelebek333/rtl8192fu-dkms.

The vendor driver also claims to support devices with ID 0bda:a725,
but that is found in some bluetooth-only devices, so it's not supported
here.

Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7dcf9fb9-1c97-ac28-5286-2236e287a18c@gmail.com

wifi: brcmfmac: wcc: Add debug messages

The message is attach and detach function are merly for debugging,
change them from pr_err to pr_debug.

Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230509100420.26094-1-matthias.bgg@kernel.org

net: Remove low_thresh in ip defrag

As low_thresh has no work in fragment reassembles,del it.
And Mark it deprecated in sysctl Document.

Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-next-2023-05-12' of git://git./linux/kernel/git/wireless/wireless-next

Kalle valo says:

====================
wireless-next patches for v6.5

The first pull request for v6.5 and only driver changes this time.
rtl8xxxu has been making lots of progress lately and now has AP mode
support.

Major changes:

rtl8xxxu

* AP mode support, initially only for rtl8188f

rtw89

* provide RSSI, EVN and SNR statistics via debugfs

* support U-NII-4 channels on 5 GHz band
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: fix use-after-free in efx_tc_flower_record_encap_match()

When writing error messages to extack for pseudo collisions, we can't
 use encap->type as encap has already been freed.  Fortunately the
 same value is stored in local variable em_type, so use that instead.

Fixes: 3c9561c0a5b9 ("sfc: support TC decap rules matching on enc_ip_tos")
Reported-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phylink: constify fwnode arguments

Both phylink_create() and phylink_fwnode_phy_connect() do not modify
the fwnode argument that they are passed, so lets constify these.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fec: using the standard return codes when xdp xmit errors

This patch standardizes the inconsistent return values for unsuccessful
XDP transmits by using standardized error codes (-EBUSY or -ENOMEM).

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: macb: Shorten max_tx_len to 4KiB - 56 on mpfs

On mpfs, with SRAM configured for 4 queues, setting max_tx_len
to GEM_TX_MAX_LEN=0x3f0 results multiple AMBA errors.
Setting max_tx_len to (4KiB - 56) removes those errors.

The details are described in erratum 1686 by Cadence

The max jumbo frame size is also reduced for mpfs to (4KiB - 56).

Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ping: Convert hlist_nulls to plain hlist.

Since introduced in commit c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP
socket kind"), ping socket does not use SLAB_TYPESAFE_BY_RCU nor check
nulls marker in loops.

Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'skb_frag_fill_page_desc'

Yunsheng Lin says:

====================
net: introduce skb_frag_fill_page_desc()

Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
It does not make much sense to calling __skb_frag_set_page()
without calling skb_frag_off_set(), as the offset may depend
on whether the page is head page or tail page, so add
skb_frag_fill_page_desc() to fill the page desc for a skb
frag.

In the future, we can make sure the page in the frag is
head page of compound page or a base page, if not, we
may warn about that and convert the tail page to head
page and update the offset accordingly, if we see a warning
about that, we also fix the caller to fill the head page
in the frag. when the fixing is done, we may remove the
warning and converting.

In this way, we can remove the compound_head() or use
page_ref_*() like the below case:
https://elixir.bootlin.com/linux/latest/source/net/core/page_pool.c#L881
https://elixir.bootlin.com/linux/latest/source/include/linux/skbuff.h#L3383

It may also convert net stack to use the folio easier.

V1: repost with all the ack/review tags included.
RFC: remove a local variable as pointed out by Simon.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: remove __skb_frag_set_page()

The remaining users calling __skb_frag_set_page() with
page being NULL seems to be doing defensive programming,
as shinfo->nr_frags is already decremented, so remove
them.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: introduce and use skb_frag_fill_page_desc()

Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.

Introduce skb_frag_fill_page_desc() to do that.

net/bpf/test_run.c does not call skb_frag_off_set() to
set the offset, "copy_from_user(page_address(page), ...)"
and 'shinfo' being part of the 'data' kzalloced in
bpf_test_init() suggest that it is assuming offset to be
initialized as zero, so call skb_frag_fill_page_desc()
with offset being zero for this case.

Also, skb_frag_set_page() is not used anymore, so remove
it.

Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: net: vxlan: Add tests for vxlan nolocalbypass option.

Add test to make sure that the localbypass option is on by default.

Add test to change vxlan localbypass to nolocalbypass and check
that packets are delivered to userspace.

Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: vxlan: Add nolocalbypass option to vxlan.

If a packet needs to be encapsulated towards a local destination IP, the
packet will undergo a "local bypass" and be injected into the Rx path as
if it was received by the target VXLAN device without undergoing
encapsulation. If such a device does not exist, the packet will be
dropped.

There are scenarios where we do not want to perform such a bypass, but
instead want the packet to be encapsulated and locally received by a
user space program for post-processing.

To that end, add a new VXLAN device attribute that controls whether a
"local bypass" is performed or not. Default to performing a bypass to
maintain existing behavior.

Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'broadcom-phy-wol'

Florian Fainelli says:

====================
Support for Wake-on-LAN for Broadcom PHYs

This patch series adds support for Wake-on-LAN to the Broadcom PHY
driver. Specifically the BCM54210E/B50212E are capable of supporting
Wake-on-LAN using an external pin typically wired up to a system's GPIO.

These PHY operate a programmable Ethernet MAC destination address
comparator which will fire up an interrupt whenever a match is received.
Because of that, it was necessary to introduce patch #1 which allows the
PHY driver's ->suspend() routine to be called unconditionally. This is
necessary in our case because we need a hook point into the device
suspend/resume flow to enable the wake-up interrupt as late as possible.

Patch #2 adds support for the Broadcom PHY library and driver for
Wake-on-LAN proper with the WAKE_UCAST, WAKE_MCAST, WAKE_BCAST,
WAKE_MAGIC and WAKE_MAGICSECURE. Note that WAKE_FILTER is supportable,
however this will require further discussions and be submitted as a RFC
series later on.

Patch #3 updates the GENET driver to defer to the PHY for Wake-on-LAN if
the PHY supports it, thus allowing the MAC to be powered down to
conserve power.

Changes in v3:

- collected Reviewed-by tags
- explicitly use return 0 in bcm54xx_phy_probe() (Paolo)

Changes in v2:

- introduce PHY_ALWAYS_CALL_SUSPEND and only have the Broadcom PHY
  driver set this flag to minimize changes to the suspend flow to only
  drivers that need it

- corrected possibly uninitialized variable in bcm54xx_set_wakeup_irq
  (Simon)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: bcmgenet: Add support for PHY-based Wake-on-LAN

If available, interrogate the PHY to find out whether we can use it for
Wake-on-LAN. This can be a more power efficient way of implementing
that feature, especially when the MAC is powered off in low power
states.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: broadcom: Add support for Wake-on-LAN

Add support for WAKE_UCAST, WAKE_MCAST, WAKE_BCAST, WAKE_MAGIC and
WAKE_MAGICSECURE. This is only supported with the BCM54210E and
compatible Ethernet PHYs. Using the in-band interrupt or an out of band
GPIO interrupts are supported.

Broadcom PHYs will generate a Wake-on-LAN level low interrupt on LED4 as
soon as one of the supported patterns is being matched. That includes
generating such an interrupt even if the PHY is operated during normal
modes. If WAKE_UCAST is selected, this could lead to the LED4 interrupt
firing up for every packet being received which is absolutely
undesirable from a performance point of view.

Because the Wake-on-LAN configuration can be set long before the system
is actually put to sleep, we cannot have an interrupt service routine to
clear on read the interrupt status register and ensure that new packet
matches will be detected.

It is desirable to enable the Wake-on-LAN interrupt as late as possible
during the system suspend process such that we limit the number of
interrupts to be handled by the system, but also conversely feed into
the Linux's system suspend way of dealing with interrupts in and around
the points of no return.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: Allow drivers to always call into ->suspend()

A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().

This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.

In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.

If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'sfc-decap'

Edward Cree says:

====================
sfc: more flexible encap matches on TC decap rules

This series extends the TC offload support on EF100 to support optionally
 matching on the IP ToS and UDP source port of the outer header in rules
 performing tunnel decapsulation.  Both of these fields allow masked
 matches if the underlying hardware supports it (current EF100 hardware
 supports masking on ToS, but only exact-match on source port).
Given that the source port is typically populated from a hash of inner
 header entropy, it's not clear whether filtering on it is useful, but
 since we can support it we may as well expose the capability.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: support TC decap rules matching on enc_src_port

Allow efx_tc_encap_match entries to include a udp_sport and a
 udp_sport_mask.  As with enc_ip_tos, use pseudos to enforce that all
 encap matches within a given <src_ip,dst_ip,udp_dport> tuple have
 the same udp_sport_mask.
Note that since we use a single layer of pseudos for both fields, two
 matches that differ in (say) udp_sport value aren't permitted to have
 different ip_tos_mask, even though this would technically be safe.
Current userland TC does not support setting enc_src_port; this patch
 was tested with an iproute2 patched to support it.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: support TC decap rules matching on enc_ip_tos

Allow efx_tc_encap_match entries to include an ip_tos and ip_tos_mask.
To avoid partially-overlapping Outer Rules (which can lead to undefined
 behaviour in the hardware), store extra "pseudo" entries in our
 encap_match hashtable, which are used to enforce that all Outer Rule
 entries within a given <src_ip,dst_ip,udp_dport> tuple (or IPv6
 equivalent) have the same ip_tos_mask.
The "direct" encap_match entry takes a reference on the "pseudo",
 allowing it to be destroyed when all "direct" entries using it are
 removed.
efx_tc_em_pseudo_type is an enum rather than just a bool because in
 future an additional pseudo-type will be added to support Conntrack
 offload.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: populate enc_ip_tos matches in MAE outer rules

Currently tc.c will block them before they get here, but following
 patch will change that.
Use the extack message from efx_mae_check_encap_match_caps() instead
 of writing a new one, since there's now more being fed in than just
 an IP version.

Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: release encap match in efx_tc_flow_free()

When force-freeing leftover entries from our match_action_ht, call
 efx_tc_delete_rule(), which releases all the rule's resources, rather
 than open-coding it.  The open-coded version was missing a call to
 release the rule's encap match (if any).
It probably doesn't matter as everything's being torn down anyway, but
 it's cleaner this way and prevents further error messages potentially
 being logged by efx_tc_encap_match_free() later on.
Move efx_tc_flow_free() further down the file to avoid introducing a
 forward declaration of efx_tc_delete_rule().

Fixes: 17654d84b47c ("sfc: add offloading of 'foreign' TC (decap) rules")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>