Alexander Duyck [Fri, 29 Dec 2017 13:51:20 +0000 (08:51 -0500)]
i40evf: Correctly populate rxitr_idx and txitr_idx
While testing code for the recent ITR changes I found that updating the Tx
ITR appeared to have no effect with everything defaulting to the Rx ITR. A
bit of digging narrowed it down the fact that we were asking the PF to
associate all causes with ITR 0 as we weren't populating the itr_idx values
for either Rx or Tx.
To correct it I have added the configuration for these values to this
patch. In addition I did some minor clean-up to just add a local pointer
for the vector map instead of dereferencing it based off of the index
repeatedly. In my opinion this makes the resultant code a bit more readable
and saves us a few characters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 29 Dec 2017 13:51:08 +0000 (08:51 -0500)]
i40e/i40evf: Use usec value instead of reg value for ITR defines
Instead of using the register value for the defines when setting up the
ring ITR we can just use the actual values and avoid the use of shifts and
macros to translate between the values we have and the values we want.
This helps to make the code more readable as we can quickly translate from
one value to the other.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 29 Dec 2017 13:50:55 +0000 (08:50 -0500)]
i40e/i40evf: Don't bother setting the CLEARPBA bit
The CLEARPBA bit in the dynamic interrupt control register actually has
no effect either way on the hardware. As per errata 28 in the XL710
specification update the interrupt is actually cleared any time the
register is written with the INTENA_MSK bit set to 0. As such the act of
toggling the enable bit actually will trigger the interrupt being
cleared and could lead to potential lost events if auto-masking is
not enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 29 Dec 2017 13:50:44 +0000 (08:50 -0500)]
i40e/i40evf: Clean-up of bits related to using q_vector->reg_idx
This patch is a further clean-up related to the change over to using
q_vector->reg_idx when accessing the ITR registers. Specifically the code
appears to have several other spots where we were computing the register
offset manually and this resulted in errors in a few spots.
Specifically in the i40evf functions for mapping queues to vectors it
appears we may have had an off by 1 error since (v_idx - 1) for the first
q_vector with an index of 0 would result in us returning -1 if I am not
mistaken.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alan Brady [Fri, 29 Dec 2017 13:50:34 +0000 (08:50 -0500)]
i40e: use changed_flags to check I40E_FLAG_DISABLE_FW_LLDP
Currently in i40e_set_priv_flags we use new_flags to check for the
I40E_FLAG_DISABLE_FW_LLDP flag. This is an issue for a few a reasons.
DISABLE_FW_LLDP is persistent across reboots/driver reloads. This means
we need some way to detect if FW LLDP is enabled on init. We do this by
trying to init_dcb and if it fails with EPERM we know LLDP is disabled
in FW.
This could be a problem on older FW versions or NPAR enabled PFs because
there are situations where the FW could disable LLDP, but they do _not_
support using this flag to change it. If we do end up in this
situation, the flag will be set, then when the user tries to change any
priv flags, the driver thinks the user is trying to disable FW LLDP on a
FW that doesn't support it and essentially forbids any priv flag
changes.
The fix is simple, instead of checking if this flag is set, we should be
checking if the user is trying to _change_ the flag on unsupported FW
versions.
This patch also adds a comment explaining that the cmpxchg is the point
of no return. Once we put the new flags into pf->flags we can't back
out.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Paweł Jabłoński [Fri, 29 Dec 2017 13:50:20 +0000 (08:50 -0500)]
i40e: Warn when setting link-down-on-close while in MFP
This patch adds a warning message when the link-down-on-close flag is
setting on. The warning is printed only on MFP devices
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Filip Sadowski [Fri, 29 Dec 2017 13:50:05 +0000 (08:50 -0500)]
i40e: Add delay after EMP reset for firmware to recover
This patch adds necessary delay for 4.33 firmware to recover after
EMP reset. Without this patch driver occasionally reinitializes
structures too quickly to communicate with firmware after EMP reset
causing AdminQ to timeout.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 29 Dec 2017 13:49:53 +0000 (08:49 -0500)]
i40e/i40evf: Clean up logic for adaptive ITR
The logic for dynamic ITR update is confusing at best as there were odd
paths chosen for how to find the rings associated with a given queue based
on the vector index and other inconsistencies throughout the code.
This patch is an attempt to clean up the logic so that we can more easily
understand what is going on. Specifically if there is a Rx or Tx ring that
is enabled in dynamic mode on the q_vector it is allowed to override the
other side of the interrupt moderation. While it isn't correct all this
patch is doing is cleaning up the logic for now so that when we come
through and fix it we can more easily identify that this is wrong.
The other big change made here is that we replace references to:
vsi->rx_rings[q_vector->v_idx]->itr_setting
with:
q_vector->rx.ring->itr_setting
The general idea is we can avoid the long pointer chase since just
accessing q_vector->rx.ring is a single pointer access versus having to
chase down vsi->rx_rings, and then finding the pointer in the array, and
finally chasing down the itr_setting from there.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Fri, 29 Dec 2017 13:49:28 +0000 (08:49 -0500)]
i40e/i40evf: Only track one ITR setting per ring instead of Tx/Rx
The rings are already split out into Tx and Rx rings so it doesn't make
sense to have any single ring store both a Tx and Rx itr_setting value.
Since that is the case drop the pair in favor of storing just a single ITR
value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alan Brady [Fri, 29 Dec 2017 13:48:33 +0000 (08:48 -0500)]
i40e: fix typo in function description
'bufer' should be 'buffer'
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linus Torvalds [Sat, 10 Feb 2018 03:32:41 +0000 (19:32 -0800)]
Merge tag 'kbuild-v4.16-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
"Makefile changes:
- enable unused-variable warning that was wrongly disabled for clang
Kconfig changes:
- warn about blank 'help' and fix existing instances
- fix 'choice' behavior to not write out invisible symbols
- fix misc weirdness
Coccinell changes:
- fix false positive of free after managed memory alloc detection
- improve performance of NULL dereference detection"
* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
kconfig: remove const qualifier from sym_expand_string_value()
kconfig: add xrealloc() helper
kconfig: send error messages to stderr
kconfig: echo stdin to stdout if either is redirected
kconfig: remove check_stdin()
kconfig: remove 'config*' pattern from .gitignnore
kconfig: show '?' prompt even if no help text is available
kconfig: do not write choice values when their dependency becomes n
coccinelle: deref_null: avoid useless computation
coccinelle: devm_free: reduce false positives
kbuild: clang: disable unused variable warnings only when constant
kconfig: Warn if help text is blank
nios2: kconfig: Remove blank help text
arm: vt8500: kconfig: Remove blank help text
MIPS: kconfig: Remove blank help text
MIPS: BCM63XX: kconfig: Remove blank help text
lib/Kconfig.debug: Remove blank help text
Staging: rtl8192e: kconfig: Remove blank help text
Staging: rtl8192u: kconfig: Remove blank help text
mmc: kconfig: Remove blank help text
...
Al Viro [Sat, 10 Feb 2018 01:35:16 +0000 (01:35 +0000)]
mconsole_proc(): don't mess with file->f_pos
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 10 Feb 2018 03:22:17 +0000 (19:22 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull misc vfs fixes from Al Viro.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
seq_file: fix incomplete reset on read from zero offset
kernfs: fix regression in kernfs_fop_write caused by wrong type
Masahiro Yamada [Thu, 8 Feb 2018 16:19:08 +0000 (01:19 +0900)]
kconfig: remove const qualifier from sym_expand_string_value()
This function returns realloc'ed memory, so the returned pointer
must be passed to free() when done. So, 'const' qualifier is odd.
It is allowed to modify the expanded string.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Thu, 8 Feb 2018 16:19:07 +0000 (01:19 +0900)]
kconfig: add xrealloc() helper
We already have xmalloc(), xcalloc(). Add xrealloc() as well
to save tedious error handling.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linus Torvalds [Fri, 9 Feb 2018 23:34:18 +0000 (15:34 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
Linus Torvalds [Fri, 9 Feb 2018 22:55:30 +0000 (14:55 -0800)]
Merge tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"A few bugfixes and some small sunrpc latency/performance improvements
before the merge window closes:
Stable fixes:
- fix an incorrect calculation of the RDMA send scatter gather
element limit
- fix an Oops when attempting to free resources after RDMA device
removal
Bugfixes:
- SUNRPC: Ensure we always release the TCP socket in a timely fashion
when the connection is shut down.
- SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
Latency/Performance:
- SUNRPC: Queue latency sensitive socket tasks to the less contended
xprtiod queue
- SUNRPC: Make the xprtiod workqueue unbounded.
- SUNRPC: Make the rpciod workqueue unbounded"
* tag 'nfs-for-4.16-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
fix parallelism for rpc tasks
Make the xprtiod workqueue unbounded.
SUNRPC: Queue latency-sensitive socket tasks to xprtiod
SUNRPC: Ensure we always close the socket after a connection shuts down
xprtrdma: Fix BUG after a device removal
xprtrdma: Fix calculation of ri_max_send_sges
Linus Torvalds [Fri, 9 Feb 2018 22:49:46 +0000 (14:49 -0800)]
Merge branch 'for-next' of git://git./linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"The highlights include:
- numerous target-core-user improvements related to queue full and
timeout handling. (MNC)
- prevent target-core-user corruption when invalid data page is
requested. (MNC)
- add target-core device action configfs attributes to allow
user-space to trigger events separate from existing attributes
exposed to end-users. (MNC)
- fix iscsi-target NULL pointer dereference 4.6+ regression in CHAP
error path. (David Disseldorp)
- avoid target-core backend UNMAP callbacks if range is zero. (Andrei
Vagin)
- fix a iscsi-target 4.14+ regression related multiple PDU logins,
that was exposed due to removal of TCP prequeue support. (Florian
Westphal + MNC)
Also, there is a iser-target bug still being worked on for post -rc1
code to address a long standing issue resulting in persistent
ib_post_send() failures, for RNICs with small max_send_sge"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (36 commits)
iscsi-target: make sure to wake up sleeping login worker
tcmu: Fix trailing semicolon
tcmu: fix cmd user after free
target: fix destroy device in target_configure_device
tcmu: allow userspace to reset ring
target core: add device action configfs files
tcmu: fix error return code in tcmu_configure_device()
target_core_user: add cmd id to broken ring message
target: add SAM_STAT_BUSY sense reason
tcmu: prevent corruption when invalid data page requested
target: don't call an unmap callback if a range length is zero
target/iscsi: avoid NULL dereference in CHAP auth error path
cxgbit: call neigh_event_send() to update MAC address
target: tcm_loop: Use seq_puts() in tcm_loop_show_info()
target: tcm_loop: Delete an unnecessary return statement in tcm_loop_submission_work()
target: tcm_loop: Delete two unnecessary variable initialisations in tcm_loop_issue_tmr()
target: tcm_loop: Combine substrings for 26 messages
target: tcm_loop: Improve a size determination in two functions
target: tcm_loop: Delete an error message for a failed memory allocation in four functions
sbp-target: Delete an error message for a failed memory allocation in three functions
...
Linus Torvalds [Fri, 9 Feb 2018 22:47:09 +0000 (14:47 -0800)]
Merge tag 'trace-v4.16-rc1' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Al Viro discovered some breakage with the parsing of the
set_ftrace_filter as well as the removing of function probes.
This fixes the code with Al's suggestions. I also added a few
selftests to test the broken cases such that they wont happen
again"
* tag 'trace-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
selftests/ftrace: Add more tests for removing of function probes
selftests/ftrace: Add some missing glob checks
selftests/ftrace: Have reset_ftrace_filter handle multiple instances
selftests/ftrace: Have reset_ftrace_filter handle modules
tracing: Fix parsing of globs with a wildcard at the beginning
ftrace: Remove incorrect setting of glob search field
Linus Torvalds [Fri, 9 Feb 2018 22:42:57 +0000 (14:42 -0800)]
Merge tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"There are a couple additional security fixes that are still being
tested that are not in this set."
* tag '4.16-minor-rc-SMB3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
Add missing structs and defines from recent SMB3.1.1 documentation
address lock imbalance warnings in smbdirect.c
cifs: silence compiler warnings showing up with gcc-8.0.0
Add some missing debug fields in server and tcon structs
Linus Torvalds [Fri, 9 Feb 2018 22:40:16 +0000 (14:40 -0800)]
Merge tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linux
Pull fbdev fix from Bartlomiej Zolnierkiewicz:
"Fix building of the omapfb driver (Tomi Valkeinen)"
* tag 'fbdev-v4.16-fix' of git://github.com/bzolnier/linux:
video: omapfb: fix missing #includes
John Allen [Fri, 9 Feb 2018 19:19:46 +0000 (13:19 -0600)]
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Fri, 9 Feb 2018 13:49:44 +0000 (14:49 +0100)]
bpf: fix rlimit in reuseport net selftest
Fix two issues in the reuseport_bpf selftests that were
reported by Linaro CI:
[...]
+ ./reuseport_bpf
---- IPv4 UDP ----
Testing EBPF mod 10...
Reprograming, testing mod 5...
./reuseport_bpf: ebpf error. log:
0: (bf) r6 = r1
1: (20) r0 = *(u32 *)skb[0]
2: (97) r0 %= 10
3: (95) exit
processed 4 insns
: Operation not permitted
+ echo FAIL
[...]
---- IPv4 TCP ----
Testing EBPF mod 10...
./reuseport_bpf: failed to bind send socket: Address already in use
+ echo FAIL
[...]
For the former adjust rlimit since this was the cause of
failure for loading the BPF prog, and for the latter add
SO_REUSEADDR.
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://bugs.linaro.org/show_bug.cgi?id=3502
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Fri, 9 Feb 2018 14:35:23 +0000 (17:35 +0300)]
sctp: verify size of a new chunk in _sctp_make_chunk()
When SCTP makes INIT or INIT_ACK packet the total chunk length
can exceed SCTP_MAX_CHUNK_LEN which leads to kernel panic when
transmitting these packets, e.g. the crash on sending INIT_ACK:
[ 597.804948] skbuff: skb_over_panic: text:
00000000ffae06e4 len:120168
put:120156 head:
000000007aa47635 data:
00000000d991c2de
tail:0x1d640 end:0xfec0 dev:<NULL>
...
[ 597.976970] ------------[ cut here ]------------
[ 598.033408] kernel BUG at net/core/skbuff.c:104!
[ 600.314841] Call Trace:
[ 600.345829] <IRQ>
[ 600.371639] ? sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.436934] skb_put+0x16c/0x200
[ 600.477295] sctp_packet_transmit+0x2095/0x26d0 [sctp]
[ 600.540630] ? sctp_packet_config+0x890/0x890 [sctp]
[ 600.601781] ? __sctp_packet_append_chunk+0x3b4/0xd00 [sctp]
[ 600.671356] ? sctp_cmp_addr_exact+0x3f/0x90 [sctp]
[ 600.731482] sctp_outq_flush+0x663/0x30d0 [sctp]
[ 600.788565] ? sctp_make_init+0xbf0/0xbf0 [sctp]
[ 600.845555] ? sctp_check_transmitted+0x18f0/0x18f0 [sctp]
[ 600.912945] ? sctp_outq_tail+0x631/0x9d0 [sctp]
[ 600.969936] sctp_cmd_interpreter.isra.22+0x3be1/0x5cb0 [sctp]
[ 601.041593] ? sctp_sf_do_5_1B_init+0x85f/0xc30 [sctp]
[ 601.104837] ? sctp_generate_t1_cookie_event+0x20/0x20 [sctp]
[ 601.175436] ? sctp_eat_data+0x1710/0x1710 [sctp]
[ 601.233575] sctp_do_sm+0x182/0x560 [sctp]
[ 601.284328] ? sctp_has_association+0x70/0x70 [sctp]
[ 601.345586] ? sctp_rcv+0xef4/0x32f0 [sctp]
[ 601.397478] ? sctp6_rcv+0xa/0x20 [sctp]
...
Here the chunk size for INIT_ACK packet becomes too big, mostly
because of the state cookie (INIT packet has large size with
many address parameters), plus additional server parameters.
Later this chunk causes the panic in skb_put_data():
skb_packet_transmit()
sctp_packet_pack()
skb_put_data(nskb, chunk->skb->data, chunk->skb->len);
'nskb' (head skb) was previously allocated with packet->size
from u16 'chunk->chunk_hdr->length'.
As suggested by Marcelo we should check the chunk's length in
_sctp_make_chunk() before trying to allocate skb for it and
discard a chunk if its size bigger than SCTP_MAX_CHUNK_LEN.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leinter@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Feb 2018 19:30:23 +0000 (14:30 -0500)]
Merge branch 's390-qeth-fixes'
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-02-09
please apply the following two qeth patches for 4.16 and stable.
One restricts a command quirk to the intended commandd type,
while the other fixes an off-by-one during data transmission
that can cause qeth to build malformed buffer descriptors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Fri, 9 Feb 2018 10:03:50 +0000 (11:03 +0100)]
s390/qeth: fix SETIP command handling
send_control_data() applies some special handling to SETIP v4 IPA
commands. But current code parses *all* command types for the SETIP
command code. Limit the command code check to IPA commands.
Fixes:
5b54e16f1a54 ("qeth: do not spin for SETIP ip assist command")
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 9 Feb 2018 10:03:49 +0000 (11:03 +0100)]
s390/qeth: fix underestimated count of buffer elements
For a memory range/skb where the last byte falls onto a page boundary
(ie. 'end' is of the form xxx...xxx001), the PFN_UP() part of the
calculation currently doesn't round up to the next PFN due to an
off-by-one error.
Thus qeth believes that the skb occupies one page less than it
actually does, and may select a IO buffer that doesn't have enough spare
buffer elements to fit all of the skb's data.
HW detects this as a malformed buffer descriptor, and raises an
exception which then triggers device recovery.
Fixes:
2863c61334aa ("qeth: refactor calculation of SBALE count")
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 9 Feb 2018 09:45:50 +0000 (17:45 +0800)]
ptr_ring: try vmalloc() when kmalloc() fails
This patch switch to use kvmalloc_array() for using a vmalloc()
fallback to help in case kmalloc() fails.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes:
2e0ab8ca83c12 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Fri, 9 Feb 2018 09:45:49 +0000 (17:45 +0800)]
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
To avoid slab to warn about exceeded size, fail early if queue
occupies more than KMALLOC_MAX_SIZE.
Reported-by: syzbot+e4d4f9ddd4295539735d@syzkaller.appspotmail.com
Fixes:
2e0ab8ca83c12 ("ptr_ring: array based FIFO for pointers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Feb 2018 19:23:04 +0000 (14:23 -0500)]
Merge branch 'stmmac-irq-fixes-cleanups'
Niklas Cassel says:
====================
stmmac irq fixes/cleanups
A couple of small stmmac irq fixes/cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Fri, 9 Feb 2018 16:22:47 +0000 (17:22 +0100)]
net: stmmac: remove redundant enable of PMT irq
For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.
For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.
Improve code readability by removing this redundant code.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Fri, 9 Feb 2018 16:22:46 +0000 (17:22 +0100)]
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Niklas Cassel [Fri, 9 Feb 2018 16:22:45 +0000 (17:22 +0100)]
net: stmmac: discard disabled flags in interrupt status register
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit
0a764db10337 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit
0a764db10337 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Falcon [Fri, 9 Feb 2018 17:41:09 +0000 (11:41 -0600)]
ibmvnic: Reset long term map ID counter
When allocating RX or TX buffer pools, the driver needs to provide a
unique mapping ID to firmware for each pool. This value is assigned
using a counter which is incremented after a new pool is created. The
ID can be an integer ranging from 1-255. When migrating to a device
that requests a different number of queues, this value was not being
reset properly. As a result, after enough migrations, the counter
exceeded the upper bound and pool creation failed. This is fixed by
resetting the counter to one in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Feb 2018 19:05:10 +0000 (14:05 -0500)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 9 Feb 2018 18:07:39 +0000 (10:07 -0800)]
Merge tag 'for-linus-4.16-rc1-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Only five small fixes for issues when running under Xen"
* tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix {set,clear}_foreign_p2m_mapping on autotranslating guests
pvcalls-back: do not return error on inet_accept EAGAIN
xen-netfront: Fix race between device setup and open
xen/grant-table: Use put_page instead of free_page
x86/xen: init %gs very early to avoid page faults with stack protector
Linus Torvalds [Fri, 9 Feb 2018 17:58:37 +0000 (09:58 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
"The main thing in this merge is the defense for the Spectre
vulnerabilities. But there are other updates as well, the changes in
more detail:
- An s390 specific implementation of the array_index_mask_nospec
function to the defense against spectre v1
- Two patches to utilize the new PPA-12/PPA-13 instructions to run
the kernel and/or user space with reduced branch predicton.
- The s390 variant of the 'retpoline' spectre v2 defense called
'expoline'. There is no return instruction for s390, instead an
indirect branch is used for function return
The s390 defense mechanism for indirect branches works by using an
execute-type instruction with the indirect branch as the target of
the execute. In effect that turns off the prediction for the
indirect branch.
- Scrub registers in entry.S that contain user controlled values to
prevent the speculative use of these values.
- Re-add the second parameter for the s390 specific runtime
instrumentation system call and move the header file to uapi. The
second parameter will continue to do nothing but older kernel
versions only accepted valid real-time signal numbers. The details
will be documented in the man-page for the system call.
- Corrections and improvements for the s390 specific documentation
- Add a line to /proc/sysinfo to display the CPU model dependent
license-internal-code identifier
- A header file include fix for eadm.
- An error message fix in the kprobes code.
- The removal of an outdated ARCH_xxx select statement"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/kconfig: Remove ARCH_WANTS_PROT_NUMA_PROT_NONE select
s390: introduce execute-trampolines for branches
s390: run user space and KVM guests with modified branch prediction
s390: add options to change branch prediction behaviour for the kernel
s390/alternative: use a copy of the facility bit mask
s390: add optimized array_index_mask_nospec
s390: scrub registers on kernel entry and KVM exit
s390/cio: fix kernel-doc usage
s390/runtime_instrumentation: re-add signum system call parameter
s390/cpum_cf: correct counter number of LAST_HOST_TRANSLATIONS
s390/kprobes: Fix %p uses in error messages
s390/runtime instrumentation: provide uapi header file
s390/sysinfo: add and display licensed internal code identifier
s390/docs: reword airq section
s390/docs: mention subchannel types
s390/cmf: fix kerneldoc
s390/eadm: fix CONFIG_BLOCK include dependency
Linus Torvalds [Fri, 9 Feb 2018 17:44:25 +0000 (09:44 -0800)]
Merge tag 'acpi-part2-4.16-rc1' of git://git./linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These are mostly fixes and cleanups, a few new quirks, a couple of
updates related to the handling of ACPI tables and ACPICA copyrights
refreshment.
Specifics:
- Update the ACPICA kernel code to upstream revision
20180105
including:
* Assorted fixes (Jung-uk Kim)
* Support for X32 ABI compilation (Anuj Mittal)
* Update of ACPICA copyrights to 2018 (Bob Moore)
- Prepare for future modifications to avoid executing the _STA
control method too early (Hans de Goede)
- Make the processor performance control library code ignore _PPC
notifications if they cannot be handled and fix up the C1 idle
state definition when it is used as a fallback state (Chen Yu,
Yazen Ghannam)
- Make it possible to use the SPCR table on x86 and to replace the
original IORT table with a new one from initrd (Prarit Bhargava,
Shunyong Yang)
- Add battery-related quirks for Asus UX360UA and UX410UAK and add
quirks for table parsing on Dell XPS 9570 and Precision M5530 (Kai
Heng Feng)
- Address static checker warnings in the CPPC code (Gustavo Silva)
- Avoid printing a raw pointer to the kernel log in the smart battery
driver (Greg Kroah-Hartman)"
* tag 'acpi-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: sbshc: remove raw pointer from printk() message
ACPI: SPCR: Make SPCR available to x86
ACPI / CPPC: Use 64-bit arithmetic instead of 32-bit
ACPI / tables: Add IORT to injectable table list
ACPI / bus: Parse tables as term_list for Dell XPS 9570 and Precision M5530
ACPICA: Update version to
20180105
ACPICA: All acpica: Update copyrights to 2018
ACPI / processor: Set default C1 idle state description
ACPI / battery: Add quirk for Asus UX360UA and UX410UAK
ACPI: processor_perflib: Do not send _PPC change notification if not ready
ACPI / scan: Use acpi_bus_get_status() to initialize ACPI_TYPE_DEVICE devs
ACPI / bus: Do not call _STA on battery devices with unmet dependencies
PCI: acpiphp_ibm: prepare for acpi_get_object_info() no longer returning status
ACPI: export acpi_bus_get_status_handle()
ACPICA: Add a missing pair of parentheses
ACPICA: Prefer ACPI_TO_POINTER() over ACPI_ADD_PTR()
ACPICA: Avoid NULL pointer arithmetic
ACPICA: Linux: add support for X32 ABI compilation
ACPI / video: Use true for boolean value
Linus Torvalds [Fri, 9 Feb 2018 17:40:33 +0000 (09:40 -0800)]
Merge tag 'pm-part2-4.16-rc1' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are mostly fixes and cleanups and removal of the no longer
needed at32ap-cpufreq driver.
Specifics:
- Drop the at32ap-cpufreq driver which is useless after the removal
of the corresponding arch (Corentin LABBE).
- Fix a regression from the 4.14 cycle in the APM idle driver by
making it initialize the polling state properly (Rafael Wysocki).
- Fix a crash on failing system suspend due to a missing check in the
cpufreq core (Bo Yan).
- Make the intel_pstate driver initialize the hardware-managed
P-state control (HWP) feature on CPU0 upon resume from system
suspend if HWP had been enabled before the system was suspended
(Chen Yu).
- Fix up the SCPI cpufreq driver after recent changes (Sudeep Holla,
Wei Yongjun).
- Avoid pointer subtractions during frequency table walks in cpufreq
(Dominik Brodowski).
- Avoid the check for ProcFeedback in ST/CZ in the cpufreq driver for
AMD processors and add a MODULE_ALIAS for cpufreq on ARM IMX (Akshu
Agrawal, Nicolas Chauvet).
- Fix the prototype of swsusp_arch_resume() on x86 (Arnd Bergmann).
- Fix up the parsing of power domains DT data (Ulf Hansson)"
* tag 'pm-part2-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
arm: imx: Add MODULE_ALIAS for cpufreq
cpufreq: Add and use cpufreq_for_each_{valid_,}entry_idx()
cpufreq: intel_pstate: Enable HWP during system resume on CPU0
cpufreq: scpi: fix error return code in scpi_cpufreq_init()
x86: hibernate: fix swsusp_arch_resume() prototype
PM / domains: Fix up domain-idle-states OF parsing
cpufreq: scpi: fix static checker warning cdev isn't an ERR_PTR
cpufreq: remove at32ap-cpufreq
cpufreq: AMD: Ignore the check for ProcFeedback in ST/CZ
x86: PM: Make APM idle driver initialize polling state
cpufreq: Skip cpufreq resume if it's not suspended
Trond Myklebust [Fri, 9 Feb 2018 14:39:42 +0000 (09:39 -0500)]
SUNRPC: Don't call __UDPX_INC_STATS() from a preemptible context
Calling __UDPX_INC_STATS() from a preemptible context leads to a
warning of the form:
BUG: using __this_cpu_add() in preemptible [
00000000] code: kworker/u5:0/31
caller is xs_udp_data_receive_workfn+0x194/0x270
CPU: 1 PID: 31 Comm: kworker/u5:0 Not tainted 4.15.0-rc8-00076-g90ea9f1 #2
Workqueue: xprtiod xs_udp_data_receive_workfn
Call Trace:
dump_stack+0x85/0xc1
check_preemption_disabled+0xce/0xe0
xs_udp_data_receive_workfn+0x194/0x270
process_one_work+0x318/0x620
worker_thread+0x20a/0x390
? process_one_work+0x620/0x620
kthread+0x120/0x130
? __kthread_bind_mask+0x60/0x60
ret_from_fork+0x24/0x30
Since we're taking a spinlock in those functions anyway, let's fix the
issue by moving the call so that it occurs under the spinlock.
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Tomi Valkeinen [Fri, 9 Feb 2018 13:43:49 +0000 (14:43 +0100)]
video: omapfb: fix missing #includes
The omapfb driver fails to build after commit
23c35f48f5fb
("pinctrl: remove include file from <linux/device.h>") because it
relies on the <linux/pinctrl/consumer.h> and <linux/seq_file.h>
being pulled in by the <linux/device.h> header implicitly.
Include these headers explicitly to avoid the build failures.
Fixes:
23c35f48f5fb ("pinctrl: remove include file from <linux/device.h>")
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
[b.zolnierkie: fix include order and patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Daniel Borkmann [Thu, 8 Feb 2018 23:26:18 +0000 (00:26 +0100)]
Merge branch 'bpf-libbpf-relo-fix-and-tests'
Jesper Dangaard Brouer says:
====================
While playing with using libbpf for the Suricata project, we had
issues LLVM >= 4.0.1 generating ELF files that could not be loaded
with libbpf (tools/lib/bpf/).
During the troubleshooting phase, I wrote a test program and improved
the debugging output in libbpf. I turned this into a selftests
program, and it also serves as a code example for libbpf in itself.
I discovered that there are at least three ELF load issues with
libbpf. I left them as TODO comments in (tools/testing/selftests/bpf)
test_libbpf.sh. I've only fixed the load issue with eh_frames, and
other types of relo-section that does not have exec flags. We can
work on the other issues later.
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jesper Dangaard Brouer [Thu, 8 Feb 2018 11:48:32 +0000 (12:48 +0100)]
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
V3: More generic skipping of relo-section (suggested by Daniel)
If clang >= 4.0.1 is missing the option '-target bpf', it will cause
llc/llvm to create two ELF sections for "Exception Frames", with
section names '.eh_frame' and '.rel.eh_frame'.
The BPF ELF loader library libbpf fails when loading files with these
sections. The other in-kernel BPF ELF loader in samples/bpf/bpf_load.c,
handle this gracefully. And iproute2 loader also seems to work with these
"eh" sections.
The issue in libbpf is caused by bpf_object__elf_collect() skipping
some sections, and later when performing relocation it will be
pointing to a skipped section, as these sections cannot be found by
bpf_object__find_prog_by_idx() in bpf_object__collect_reloc().
This is a general issue that also occurs for other sections, like
debug sections which are also skipped and can have relo section.
As suggested by Daniel. To avoid keeping state about all skipped
sections, instead perform a direct qlookup in the ELF object. Lookup
the section that the relo-section points to and check if it contains
executable machine instructions (denoted by the sh_flags
SHF_EXECINSTR). Use this check to also skip irrelevant relo-sections.
Note, for samples/bpf/ the '-target bpf' parameter to clang cannot be used
due to incompatibility with asm embedded headers, that some of the samples
include. This is explained in more details by Yonghong Song in bpf_devel_QA.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jesper Dangaard Brouer [Thu, 8 Feb 2018 11:48:27 +0000 (12:48 +0100)]
selftests/bpf: add selftest that use test_libbpf_open
This script test_libbpf.sh will be part of the 'make run_tests'
invocation, but can also be invoked manually in this directory,
and a verbose mode can be enabled via setting the environment
variable $VERBOSE like:
$ VERBOSE=yes ./test_libbpf.sh
The script contains some tests that are commented out, as they
currently fail. They are reminders about what we need to improve
for the libbpf loader library.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jesper Dangaard Brouer [Thu, 8 Feb 2018 11:48:22 +0000 (12:48 +0100)]
selftests/bpf: add test program for loading BPF ELF files
V2: Moved program into selftests/bpf from tools/libbpf
This program can be used on its own for testing/debugging if a
BPF ELF-object file can be loaded with libbpf (from tools/lib/bpf).
If something is wrong with the ELF object, the program have
a --debug mode that will display the ELF sections and especially
the skipped sections. This allows for quickly identifying the
problematic ELF section number, which can be corrolated with the
readelf tool.
The program signal error via return codes, and also have
a --quiet mode, which is practical for use in scripts like
selftests/bpf.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jesper Dangaard Brouer [Thu, 8 Feb 2018 11:48:17 +0000 (12:48 +0100)]
tools/libbpf: improve the pr_debug statements to contain section numbers
While debugging a bpf ELF loading issue, I needed to correlate the
ELF section number with the failed relocation section reference.
Thus, add section numbers/index to the pr_debug.
In debug mode, also print section that were skipped. This helped
me identify that a section (.eh_frame) was skipped, and this was
the reason the relocation section (.rel.eh_frame) could not find
that section number.
The section numbers corresponds to the readelf tools Section Headers [Nr].
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jesper Dangaard Brouer [Thu, 8 Feb 2018 11:48:12 +0000 (12:48 +0100)]
bpf: Sync kernel ABI header with tooling header for bpf_common.h
I recently fixed up a lot of commits that forgot to keep the tooling
headers in sync. And then I forgot to do the same thing in commit
cb5f7334d479 ("bpf: add comments to BPF ld/ldx sizes"). Let correct
that before people notice ;-).
Lawrence did partly fix/sync this for bpf.h in commit
d6d4f60c3a09
("bpf: add selftest for tcpbpf").
Fixes:
cb5f7334d479 ("bpf: add comments to BPF ld/ldx sizes")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 8 Feb 2018 23:18:32 +0000 (15:18 -0800)]
Merge tag 'nfsd-4.16' of git://linux-nfs.org/~bfields/linux
Pull nfsd update from Bruce Fields:
"A fairly small update this time around. Some cleanup, RDMA fixes,
overlayfs fixes, and a fix for an NFSv4 state bug.
The bigger deal for nfsd this time around was Jeff Layton's
already-merged i_version patches"
* tag 'nfsd-4.16' of git://linux-nfs.org/~bfields/linux:
svcrdma: Fix Read chunk round-up
NFSD: hide unused svcxdr_dupstr()
nfsd: store stat times in fill_pre_wcc() instead of inode times
nfsd: encode stat->mtime for getattr instead of inode->i_mtime
nfsd: return RESOURCE not GARBAGE_ARGS on too many ops
nfsd4: don't set lock stateid's sc_type to CLOSED
nfsd: Detect unhashed stids in nfsd4_verify_open_stid()
sunrpc: remove dead code in svc_sock_setbufsize
svcrdma: Post Receives in the Receive completion handler
nfsd4: permit layoutget of executable-only files
lockd: convert nlm_rqst.a_count from atomic_t to refcount_t
lockd: convert nlm_lockowner.count from atomic_t to refcount_t
lockd: convert nsm_handle.sm_count from atomic_t to refcount_t
Linus Torvalds [Thu, 8 Feb 2018 22:39:29 +0000 (14:39 -0800)]
Merge branch 'idr-2018-02-06' of git://git.infradead.org/users/willy/linux-dax
Pull idr updates from Matthew Wilcox:
- test-suite improvements
- replace the extended API by improving the normal API
- performance improvement for IDRs which are 1-based rather than
0-based
- add documentation
* 'idr-2018-02-06' of git://git.infradead.org/users/willy/linux-dax:
idr: Add documentation
idr: Make 1-based IDRs more efficient
idr: Warn if old iterators see large IDs
idr: Rename idr_for_each_entry_ext
idr: Remove idr_alloc_ext
cls_u32: Convert to idr_alloc_u32
cls_u32: Reinstate cyclic allocation
cls_flower: Convert to idr_alloc_u32
cls_bpf: Convert to use idr_alloc_u32
cls_basic: Convert to use idr_alloc_u32
cls_api: Convert to idr_alloc_u32
net sched actions: Convert to use idr_alloc_u32
idr: Add idr_alloc_u32 helper
idr: Delete idr_find_ext function
idr: Delete idr_replace_ext function
idr: Delete idr_remove_ext function
IDR test suite: Check handling negative end correctly
idr test suite: Fix ida_test_random()
radix tree test suite: Remove ARRAY_SIZE
Linus Torvalds [Thu, 8 Feb 2018 22:37:32 +0000 (14:37 -0800)]
Merge tag 'gcc-plugins-v4.16-rc1' of git://git./linux/kernel/git/kees/linux
Pull gcc plugins updates from Kees Cook:
- update includes for gcc 8 (Valdis Kletnieks)
- update initializers for gcc 8
* tag 'gcc-plugins-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Use dynamic initializers
gcc-plugins: Add include required by GCC release 8
Olga Kornievskaia [Thu, 29 Jun 2017 13:25:36 +0000 (09:25 -0400)]
fix parallelism for rpc tasks
Hi folks,
On a multi-core machine, is it expected that we can have parallel RPCs
handled by each of the per-core workqueue?
In testing a read workload, observing via "top" command that a single
"kworker" thread is running servicing the requests (no parallelism).
It's more prominent while doing these operations over krb5p mount.
What has been suggested by Bruce is to try this and in my testing I
see then the read workload spread among all the kworker threads.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Heiner Kallweit [Thu, 8 Feb 2018 20:01:48 +0000 (21:01 +0100)]
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
This condition wasn't adjusted when PHY_IGNORE_INTERRUPT (-2) was added
long ago. In case of PHY_IGNORE_INTERRUPT the MAC interrupt indicates
also PHY state changes and we should do what the symbol says.
Fixes:
84a527a41f38 ("net: phylib: fix interrupts re-enablement in phy_start")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dean Nelson [Thu, 8 Feb 2018 19:21:05 +0000 (14:21 -0500)]
net: thunder: change q_len's type to handle max ring size
The Cavium thunder nicvf driver supports rx/tx rings of up to 65536 entries per.
The number of entires are stored in the q_len member of struct q_desc_mem. The
problem is that q_len being a u16, results in 65536 becoming 0.
In getting pointers to descriptors in the rings, the driver uses q_len minus 1
as a mask after incrementing the pointer, in order to go back to the beginning
and not go past the end of the ring.
With the q_len set to 0 the mask is no longer correct and the driver does go
beyond the end of the ring, causing various ills. Usually the first thing that
shows up is a "NETDEV WATCHDOG: enP2p1s0f1 (nicvf): transmit queue 7 timed out"
warning.
This patch remedies the problem by changing q_len to a u32.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 8 Feb 2018 20:32:25 +0000 (15:32 -0500)]
Merge tag 'wireless-drivers-next-for-davem-2018-02-08' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hoang Le [Thu, 8 Feb 2018 16:16:25 +0000 (17:16 +0100)]
tipc: fix skb truesize/datasize ratio control
In commit
d618d09a68e4 ("tipc: enforce valid ratio between skb truesize
and contents") we introduced a test for ensuring that the condition
truesize/datasize <= 4 is true for a received buffer. Unfortunately this
test has two problems.
- Because of the integer arithmetics the test
if (skb->truesize / buf_roundup_len(skb) > 4) will miss all
ratios [4 < ratio < 5], which was not the intention.
- The buffer returned by skb_copy() inherits skb->truesize of the
original buffer, which doesn't help the situation at all.
In this commit, we change the ratio condition and replace skb_copy()
with a call to skb_copy_expand() to finally get this right.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera [Thu, 8 Feb 2018 15:10:39 +0000 (16:10 +0100)]
net/sched: cls_u32: fix cls_u32 on filter replace
The following sequence is currently broken:
# tc qdisc add dev foo ingress
# tc filter replace dev foo protocol all ingress \
u32 match u8 0 0 action mirred egress mirror dev bar1
# tc filter replace dev foo protocol all ingress \
handle 800::800 pref 49152 \
u32 match u8 0 0 action mirred egress mirror dev bar2
Error: cls_u32: Key node flags do not match passed flags.
We have an error talking to the kernel, -1
The error comes from u32_change() when comparing new and
existing flags. The existing ones always contains one of
TCA_CLS_FLAGS_{,NOT}_IN_HW flag depending on offloading state.
These flags cannot be passed from userspace so the condition
(n->flags != flags) in u32_change() always fails.
Fix the condition so the flags TCA_CLS_FLAGS_NOT_IN_HW and
TCA_CLS_FLAGS_IN_HW are not taken into account.
Fixes:
24d3dc6d27ea ("net/sched: cls_u32: Reflect HW offload status")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Williams [Thu, 8 Feb 2018 06:34:24 +0000 (22:34 -0800)]
mpls, nospec: Sanitize array index in mpls_label_ok()
mpls_label_ok() validates that the 'platform_label' array index from a
userspace netlink message payload is valid. Under speculation the
mpls_label_ok() result may not resolve in the CPU pipeline until after
the index is used to access an array element. Sanitize the index to zero
to prevent userspace-controlled arbitrary out-of-bounds speculation, a
precursor for a speculative execution side channel vulnerability.
Cc: <stable@vger.kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sowmini Varadhan [Sat, 3 Feb 2018 12:26:51 +0000 (04:26 -0800)]
rds: tcp: use rds_destroy_pending() to synchronize netns/module teardown and rds connection/workq management
An rds_connection can get added during netns deletion between lines 528
and 529 of
506 static void rds_tcp_kill_sock(struct net *net)
:
/* code to pull out all the rds_connections that should be destroyed */
:
528 spin_unlock_irq(&rds_tcp_conn_lock);
529 list_for_each_entry_safe(tc, _tc, &tmp_list, t_tcp_node)
530 rds_conn_destroy(tc->t_cpath->cp_conn);
Such an rds_connection would miss out the rds_conn_destroy()
loop (that cancels all pending work) and (if it was scheduled
after netns deletion) could trigger the use-after-free.
A similar race-window exists for the module unload path
in rds_tcp_exit -> rds_tcp_destroy_conns
Concurrency with netns deletion (rds_tcp_kill_sock()) must be handled
by checking check_net() before enqueuing new work or adding new
connections.
Concurrency with module-unload is handled by maintaining a module
specific flag that is set at the start of the module exit function,
and must be checked before enqueuing new work or adding new connections.
This commit refactors existing RDS_DESTROY_PENDING checks added by
commit
3db6e0d172c9 ("rds: use RCU to synchronize work-enqueue with
connection teardown") and consolidates all the concurrency checks
listed above into the function rds_destroy_pending().
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 8 Feb 2018 20:20:41 +0000 (12:20 -0800)]
Merge tag 'for-linus-4.16' of git://git./linux/kernel/git/hubcap/linux
Pull orangefs updates from Mike Marshall:
"Mostly cleanups, but three bug fixes:
- don't pass garbage return codes back up the call chain (Mike
Marshall)
- fix stale inode test (Martin Brandenburg)
- fix off-by-one errors (Xiongfeng Wang)
Also add Martin as a reviewer in the Maintainers file"
* tag 'for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: reverse sense of is-inode-stale test in d_revalidate
orangefs: simplify orangefs_inode_is_stale
Orangefs: don't propogate whacky error codes
orangefs: use correct string length
orangefs: make orangefs_make_bad_inode static
orangefs: remove ORANGEFS_KERNEL_DEBUG
orangefs: remove gossip_ldebug and gossip_lerr
orangefs: make orangefs_client_debug_init static
MAINTAINERS: update orangefs list and add myself as reviewer
Kees Cook [Thu, 8 Feb 2018 01:44:38 +0000 (17:44 -0800)]
net: Whitelist the skbuff_head_cache "cb" field
Most callers of put_cmsg() use a "sizeof(foo)" for the length argument.
Within put_cmsg(), a copy_to_user() call is made with a dynamic size, as a
result of the cmsg header calculations. This means that hardened usercopy
will examine the copy, even though it was technically a fixed size and
should be implicitly whitelisted. All the put_cmsg() calls being built
from values in skbuff_head_cache are coming out of the protocol-defined
"cb" field, so whitelist this field entirely instead of creating per-use
bounce buffers, for which there are concerns about performance.
Original report was:
Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLAB object 'skbuff_head_cache' (offset 64, size 16)!
WARNING: CPU: 0 PID: 3663 at mm/usercopy.c:81 usercopy_warn+0xdb/0x100 mm/usercopy.c:76
...
__check_heap_object+0x89/0xc0 mm/slab.c:4426
check_heap_object mm/usercopy.c:236 [inline]
__check_object_size+0x272/0x530 mm/usercopy.c:259
check_object_size include/linux/thread_info.h:112 [inline]
check_copy_size include/linux/thread_info.h:143 [inline]
copy_to_user include/linux/uaccess.h:154 [inline]
put_cmsg+0x233/0x3f0 net/core/scm.c:242
sock_recv_errqueue+0x200/0x3e0 net/core/sock.c:2913
packet_recvmsg+0xb2e/0x17a0 net/packet/af_packet.c:3296
sock_recvmsg_nosec net/socket.c:803 [inline]
sock_recvmsg+0xc9/0x110 net/socket.c:810
___sys_recvmsg+0x2a4/0x640 net/socket.c:2179
__sys_recvmmsg+0x2a9/0xaf0 net/socket.c:2287
SYSC_recvmmsg net/socket.c:2368 [inline]
SyS_recvmmsg+0xc4/0x160 net/socket.c:2352
entry_SYSCALL_64_fastpath+0x29/0xa0
Reported-by: syzbot+e2d6cfb305e9f3911dea@syzkaller.appspotmail.com
Fixes:
6d07d1cd300f ("usercopy: Restrict non-usercopy caches to size 0")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mathieu Malaterre [Wed, 7 Feb 2018 19:35:00 +0000 (20:35 +0100)]
net: Extra '_get' in declaration of arch_get_platform_mac_address
In commit
c7f5d105495a ("net: Add eth_platform_get_mac_address() helper."),
two declarations were added:
int eth_platform_get_mac_address(struct device *dev, u8 *mac_addr);
unsigned char *arch_get_platform_get_mac_address(void);
An extra '_get' was introduced in arch_get_platform_get_mac_address, remove
it. Fix compile warning using W=1:
CC net/ethernet/eth.o
net/ethernet/eth.c:523:24: warning: no previous prototype for ‘arch_get_platform_mac_address’ [-Wmissing-prototypes]
unsigned char * __weak arch_get_platform_mac_address(void)
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
AR net/ethernet/built-in.o
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 8 Feb 2018 20:12:04 +0000 (12:12 -0800)]
Merge tag 'afs-next-
20180208' of git://git./linux/kernel/git/dhowells/linux-fs
Pull afs updates from David Howells:
"Four fixes:
- add a missing put
- two fixes to reset the address iteration cursor correctly
- fix setting up the fileserver iteration cursor.
Two cleanups:
- remove some dead code
- rearrange a function to be more logically laid out
And one new feature:
- Support AFS dynamic root.
With this one should be able to do, say:
mkdir /afs
mount -t afs none /afs -o dyn
to create a dynamic root and then, provided you have keyutils
installed, do:
ls /afs/grand.central.org
and:
ls /afs/umich.edu
to list the root volumes of both those organisations' AFS cells
without requiring any other setup (the kernel upcall to a program
in the keyutils package to do DNS access as does NFS)"
* tag 'afs-next-
20180208' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Support the AFS dynamic root
afs: Rearrange afs_select_fileserver() a little
afs: Remove unused code
afs: Fix server list handling
afs: Need to clear responded flag in addr cursor
afs: Fix missing cursor clearance
afs: Add missing afs_put_cell()
Nathan Fontenot [Wed, 7 Feb 2018 19:00:24 +0000 (13:00 -0600)]
ibmvnic: queue reset when CRQ gets closed during reset
While handling a driver reset we get a H_CLOSED return trying
to send a CRQ event. When this occurs we need to queue up another
reset attempt. Without doing this we see instances where the driver
is left in a closed state because the reset failed and there is no
further attempts to reset the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 7 Feb 2018 16:17:29 +0000 (10:17 -0600)]
atm: he: use 64-bit arithmetic instead of 32-bit
Add suffix ULL to constants 272, 204, 136 and 68 in order to give the
compiler complete information about the proper arithmetic to use.
Notice that these constants are used in contexts that expect
expressions of type unsigned long long (64 bits, unsigned).
The following expressions are currently being evaluated using 32-bit
arithmetic:
272 * mult
204 * mult
136 * mult
68 * mult
Addresses-Coverity-ID: 201058
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 8 Feb 2018 20:03:54 +0000 (12:03 -0800)]
Merge tag 'iommu-updates-v4.16' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time there are not a lot of changes coming from the IOMMU side.
That is partly because I returned from my parental leave late in the
development process and probably partly because everyone was busy with
Spectre and Meltdown mitigation work and didn't find the time for
IOMMU work. So here are the few changes that queued up for this merge
window:
- 5-level page-table support for the Intel IOMMU.
- error reporting improvements for the AMD IOMMU driver
- additional DT bindings for ipmmu-vmsa (Renesas)
- small fixes and cleanups"
* tag 'iommu-updates-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Clean up of_iommu_init_fn
iommu/ipmmu-vmsa: Remove redundant of_iommu_init_fn hook
iommu/msm: Claim bus ops on probe
iommu/vt-d: Enable 5-level paging mode in the PASID entry
iommu/vt-d: Add a check for 5-level paging support
iommu/vt-d: Add a check for 1GB page support
iommu/vt-d: Enable upto 57 bits of domain address width
iommu/vt-d: Use domain instead of cache fetching
iommu/exynos: Don't unconditionally steal bus ops
iommu/omap: Fix debugfs_create_*() usage
iommu/vt-d: clean up pr_irq if request_threaded_irq fails
iommu: Check the result of iommu_group_get() for NULL
iommu/ipmmu-vmsa: Add r8a779(70|95) DT bindings
iommu/ipmmu-vmsa: Add r8a7796 DT binding
iommu/amd: Set the device table entry PPR bit for IOMMU V2 devices
iommu/amd - Record more information about unknown events
Linus Torvalds [Thu, 8 Feb 2018 19:48:49 +0000 (11:48 -0800)]
Merge branch 'pcmcia' of git://git./linux/kernel/git/brodo/pcmcia
Pull pcmcia updates from Dominik Brodowski:
"The linux-pcmcia mailing list was shut down, so offer an alternative
path for patches in MAINTAINERS.
Also, throw in two odd fixes for the pcmcia subsystem"
* 'pcmcia' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia:
pcmcia: soc_common: Handle return value of clk_prepare_enable
pcmcia: use proper printk format for resource
pcmcia: remove mailing list, update MAINTAINERS
Linus Torvalds [Thu, 8 Feb 2018 19:42:05 +0000 (11:42 -0800)]
Merge tag 'drm-for-v4.16-part2-fixes' of git://people.freedesktop.org/~airlied/linux
Pull more drm updates from Dave Airlie:
"Ben missed sending his nouveau tree, but he really didn't have much
stuff in it:
- GP108 acceleration support is enabled by "secure boot" support
- some clockgating work on Kepler, and bunch of fixes
- the bulk of the diff is regenerated firmware files, the change to
them really isn't that large.
Otherwise this contains regular Intel and AMDGPU fixes"
* tag 'drm-for-v4.16-part2-fixes' of git://people.freedesktop.org/~airlied/linux: (59 commits)
drm/i915/bios: add DP max link rate to VBT child device struct
drm/i915/cnp: Properly handle VBT ddc pin out of bounds.
drm/i915/cnp: Ignore VBT request for know invalid DDC pin.
drm/i915/cmdparser: Do not check past the cmd length.
drm/i915/cmdparser: Check reg_table_count before derefencing.
drm/i915/bxt, glk: Increase PCODE timeouts during CDCLK freq changing
drm/i915/gvt: Use KVM r/w to access guest opregion
drm/i915/gvt: Fix aperture read/write emulation when enable x-no-mmap=on
drm/i915/gvt: only reset execlist state of one engine during VM engine reset
drm/i915/gvt: refine intel_vgpu_submission_ops as per engine ops
drm/amdgpu: re-enable CGCG on CZ and disable on ST
drm/nouveau/clk: fix gcc-7 -Wint-in-bool-context warning
drm/nouveau/mmu: Fix trailing semicolon
drm/nouveau: Introduce NvPmEnableGating option
drm/nouveau: Add support for SLCG for Kepler2
drm/nouveau: Add support for BLCG on Kepler2
drm/nouveau: Add support for BLCG on Kepler1
drm/nouveau: Add support for basic clockgating on Kepler1
drm/nouveau/kms/nv50: fix handling of gamma since atomic conversion
drm/nouveau/kms/nv50: use INTERPOLATE_257_UNITY_RANGE LUT on newer chipsets
...
Linus Torvalds [Thu, 8 Feb 2018 19:38:59 +0000 (11:38 -0800)]
Merge tag 'ceph-for-4.16-rc1' of git://github.com/ceph/ceph-client
Pull ceph updates from Ilya Dryomov:
"Things have been very quiet on the rbd side, as work continues on the
big ticket items slated for the next merge window.
On the CephFS side we have a large number of cap handling
improvements, a fix for our long-standing abuse of ->journal_info in
ceph_readpages() and yet another dentry pointer management patch"
* tag 'ceph-for-4.16-rc1' of git://github.com/ceph/ceph-client:
ceph: improving efficiency of syncfs
libceph: check kstrndup() return value
ceph: try to allocate enough memory for reserved caps
ceph: fix race of queuing delayed caps
ceph: delete unreachable code in ceph_check_caps()
ceph: limit rate of cap import/export error messages
ceph: fix incorrect snaprealm when adding caps
ceph: fix un-balanced fsc->writeback_count update
ceph: track read contexts in ceph_file_info
ceph: avoid dereferencing invalid pointer during cached readdir
ceph: use atomic_t for ceph_inode_info::i_shared_gen
ceph: cleanup traceless reply handling for rename
ceph: voluntarily drop Fx cap for readdir request
ceph: properly drop caps for setattr request
ceph: voluntarily drop Lx cap for link/rename requests
ceph: voluntarily drop Ax cap for requests that create new inode
rbd: whitelist RBD_FEATURE_OPERATIONS feature bit
rbd: don't NULL out ->obj_request in rbd_img_obj_parent_read_full()
rbd: use kmem_cache_zalloc() in rbd_img_request_create()
rbd: obj_request->completion is unused
Nicolas Pitre [Thu, 8 Feb 2018 03:08:08 +0000 (22:08 -0500)]
cramfs: better MTD dependency expression
Commit
b9f5fb1800d8 ("cramfs: fix MTD dependency") did what it says.
Since commit
9059a3493efe ("kconfig: fix relational operators for bool
and tristate symbols") it is possible to do it slightly better though.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian Brauner [Wed, 7 Feb 2018 12:53:20 +0000 (13:53 +0100)]
rtnetlink: require unique netns identifier
Since we've added support for IFLA_IF_NETNSID for RTM_{DEL,GET,SET,NEW}LINK
it is possible for userspace to send us requests with three different
properties to identify a target network namespace. This affects at least
RTM_{NEW,SET}LINK. Each of them could potentially refer to a different
network namespace which is confusing. For legacy reasons the kernel will
pick the IFLA_NET_NS_PID property first and then look for the
IFLA_NET_NS_FD property but there is no reason to extend this type of
behavior to network namespace ids. The regression potential is quite
minimal since the rtnetlink requests in question either won't allow
IFLA_IF_NETNSID requests before 4.16 is out (RTM_{NEW,SET}LINK) or don't
support IFLA_NET_NS_{PID,FD} (RTM_{DEL,GET}LINK) in the first place.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 7 Feb 2018 09:14:46 +0000 (17:14 +0800)]
tuntap: add missing xdp flush
When using devmap to redirect packets between interfaces,
xdp_do_flush() is usually a must to flush any batched
packets. Unfortunately this is missed in current tuntap
implementation.
Unlike most hardware driver which did XDP inside NAPI loop and call
xdp_do_flush() at then end of each round of poll. TAP did it in the
context of process e.g tun_get_user(). So fix this by count the
pending redirected packets and flush when it exceeds NAPI_POLL_WEIGHT
or MSG_MORE was cleared by sendmsg() caller.
With this fix, xdp_redirect_map works again between two TAPs.
Fixes:
761876c857cb ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Tue, 6 Feb 2018 00:34:41 +0000 (09:34 +0900)]
kconfig: send error messages to stderr
These messages should be directed to stderr.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
Masahiro Yamada [Thu, 8 Feb 2018 05:56:40 +0000 (14:56 +0900)]
kconfig: echo stdin to stdout if either is redirected
If stdio is not tty, conf_askvalue() puts additional new line to
prevent prompts from being concatenated into a single line. This
care is missing in conf_choice(), so a 'choice' prompt and the next
prompt are shown in the same line.
Move the code into xfgets() to cater to all cases. To improve this
more, let's echo stdin to stdout. This clarifies what keys were
input from stdio and the stdout looks like as if it were from tty.
I removed the isatty(2) check since stderr is unrelated here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
Masahiro Yamada [Thu, 8 Feb 2018 05:56:39 +0000 (14:56 +0900)]
kconfig: remove check_stdin()
Except silentoldconfig, valid_stdin is 1, so check_stdin() is no-op.
oldconfig and silentoldconfig work almost in the same way except that
the latter generates additional files under include/. Both ask users
for input for new symbols.
I do not know why only silentoldconfig requires stdio be tty.
$ rm -f .config; touch .config
$ yes "" | make oldconfig > stdout
$ rm -f .config; touch .config
$ yes "" | make silentoldconfig > stdout
make[1]: *** [silentoldconfig] Error 1
make: *** [silentoldconfig] Error 2
$ tail -n 4 stdout
Console input/output is redirected. Run 'make oldconfig' to update configuration.
scripts/kconfig/Makefile:40: recipe for target 'silentoldconfig' failed
Makefile:507: recipe for target 'silentoldconfig' failed
Redirection is useful, for example, for testing where we want to give
particular key inputs from a test file, then check the result.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
Masahiro Yamada [Tue, 6 Feb 2018 00:34:45 +0000 (09:34 +0900)]
kconfig: remove 'config*' pattern from .gitignnore
I could not figure out why this pattern should be ignored.
Checking commit
1e65174a3378 ("Add some basic .gitignore files")
did not help.
Let's remove this pattern, then see if it is really needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
Masahiro Yamada [Tue, 6 Feb 2018 00:34:43 +0000 (09:34 +0900)]
kconfig: show '?' prompt even if no help text is available
'make config', 'make oldconfig', etc. always receive '?' as a valid
input and show useful information even if no help text is available.
------------------------>8------------------------
foo (FOO) [N/y] (NEW) ?
There is no help available for this option.
Symbol: FOO [=n]
Type : bool
Prompt: foo
Defined at Kconfig:1
------------------------>8------------------------
However, '?' is not shown in the prompt if its help text is missing.
Let's show '?' all the time so that the prompt and the behavior match.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
Masahiro Yamada [Tue, 6 Feb 2018 00:34:42 +0000 (09:34 +0900)]
kconfig: do not write choice values when their dependency becomes n
"# CONFIG_... is not set" for choice values are wrongly written into
the .config file if they are once visible, then become invisible later.
Test case
---------
---------------------------(Kconfig)----------------------------
config A
bool "A"
choice
prompt "Choice ?"
depends on A
config CHOICE_B
bool "Choice B"
config CHOICE_C
bool "Choice C"
endchoice
----------------------------------------------------------------
---------------------------(.config)----------------------------
CONFIG_A=y
----------------------------------------------------------------
With the Kconfig and .config above,
$ make config
scripts/kconfig/conf --oldaskconfig Kconfig
*
* Linux Kernel Configuration
*
A (A) [Y/n] n
#
# configuration written to .config
#
$ cat .config
#
# Automatically generated file; DO NOT EDIT.
# Linux Kernel Configuration
#
# CONFIG_A is not set
# CONFIG_CHOICE_B is not set
# CONFIG_CHOICE_C is not set
Here,
# CONFIG_CHOICE_B is not set
# CONFIG_CHOICE_C is not set
should not be written into the .config file because their dependency
"depends on A" is unmet.
Currently, there is no code that clears SYMBOL_WRITE of choice values.
Clear SYMBOL_WRITE for all symbols in sym_calc_value(), then set it
again after calculating visibility. To simplify the logic, set the
flag if they have non-n visibility, regardless of types, and regardless
of whether they are choice values or not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Ulf Magnusson <ulfalizer@gmail.com>
Nicolas Dichtel [Tue, 6 Feb 2018 13:48:32 +0000 (14:48 +0100)]
netlink: ensure to loop over all netns in genlmsg_multicast_allns()
Nowadays, nlmsg_multicast() returns only 0 or -ESRCH but this was not the
case when commit
134e63756d5f was pushed.
However, there was no reason to stop the loop if a netns does not have
listeners.
Returns -ESRCH only if there was no listeners in all netns.
To avoid having the same problem in the future, I didn't take the
assumption that nlmsg_multicast() returns only 0 or -ESRCH.
Fixes:
134e63756d5f ("genetlink: make netns aware")
CC: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Thu, 8 Feb 2018 15:59:07 +0000 (15:59 +0000)]
rxrpc: Don't put crypto buffers on the stack
Don't put buffers of data to be handed to crypto on the stack as this may
cause an assertion failure in the kernel (see below). Fix this by using an
kmalloc'd buffer instead.
kernel BUG at ./include/linux/scatterlist.h:147!
...
RIP: 0010:rxkad_encrypt_response.isra.6+0x191/0x1b0 [rxrpc]
RSP: 0018:
ffffbe2fc06cfca8 EFLAGS:
00010246
RAX:
0000000000000000 RBX:
ffff989277d59900 RCX:
0000000000000028
RDX:
0000259dc06cfd88 RSI:
0000000000000025 RDI:
ffffbe30406cfd88
RBP:
ffffbe2fc06cfd60 R08:
ffffbe2fc06cfd08 R09:
ffffbe2fc06cfd08
R10:
0000000000000000 R11:
0000000000000000 R12:
1ffff7c5f80d9f95
R13:
ffffbe2fc06cfd88 R14:
ffff98927a3f7aa0 R15:
ffffbe2fc06cfd08
FS:
0000000000000000(0000) GS:
ffff98927fc00000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
000055b1ff28f0f8 CR3:
000000001b412003 CR4:
00000000003606f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000fffe0ff0 DR7:
0000000000000400
Call Trace:
rxkad_respond_to_challenge+0x297/0x330 [rxrpc]
rxrpc_process_connection+0xd1/0x690 [rxrpc]
? process_one_work+0x1c3/0x680
? __lock_is_held+0x59/0xa0
process_one_work+0x249/0x680
worker_thread+0x3a/0x390
? process_one_work+0x680/0x680
kthread+0x121/0x140
? kthread_create_worker_on_cpu+0x70/0x70
ret_from_fork+0x3a/0x50
Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 8 Feb 2018 18:44:25 +0000 (10:44 -0800)]
Merge tag 'arm64-upstream' of git://git./linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
"As I mentioned in the last pull request, there's a second batch of
security updates for arm64 with mitigations for Spectre/v1 and an
improved one for Spectre/v2 (via a newly defined firmware interface
API).
Spectre v1 mitigation:
- back-end version of array_index_mask_nospec()
- masking of the syscall number to restrict speculation through the
syscall table
- masking of __user pointers prior to deference in uaccess routines
Spectre v2 mitigation update:
- using the new firmware SMC calling convention specification update
- removing the current PSCI GET_VERSION firmware call mitigation as
vendors are deploying new SMCCC-capable firmware
- additional branch predictor hardening for synchronous exceptions
and interrupts while in user mode
Meltdown v3 mitigation update:
- Cavium Thunder X is unaffected but a hardware erratum gets in the
way. The kernel now starts with the page tables mapped as global
and switches to non-global if kpti needs to be enabled.
Other:
- Theoretical trylock bug fixed"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (38 commits)
arm64: Kill PSCI_GET_VERSION as a variant-2 workaround
arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support
arm/arm64: smccc: Implement SMCCC v1.1 inline primitive
arm/arm64: smccc: Make function identifiers an unsigned quantity
firmware/psci: Expose SMCCC version through psci_ops
firmware/psci: Expose PSCI conduit
arm64: KVM: Add SMCCC_ARCH_WORKAROUND_1 fast handling
arm64: KVM: Report SMCCC_ARCH_WORKAROUND_1 BP hardening support
arm/arm64: KVM: Turn kvm_psci_version into a static inline
arm/arm64: KVM: Advertise SMCCC v1.1
arm/arm64: KVM: Implement PSCI 1.0 support
arm/arm64: KVM: Add smccc accessors to PSCI code
arm/arm64: KVM: Add PSCI_VERSION helper
arm/arm64: KVM: Consolidate the PSCI include files
arm64: KVM: Increment PC after handling an SMC trap
arm: KVM: Fix SMCCC handling of unimplemented SMC/HVC calls
arm64: KVM: Fix SMCCC handling of unimplemented SMC/HVC calls
arm64: entry: Apply BP hardening for suspicious interrupts from EL0
arm64: entry: Apply BP hardening for high-priority synchronous exceptions
arm64: futex: Mask __user pointers prior to dereference
...
Linus Torvalds [Thu, 8 Feb 2018 18:41:00 +0000 (10:41 -0800)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio/vhost updates from Michael Tsirkin:
"virtio, vhost: fixes, cleanups, features
This includes the disk/cache memory stats for for the virtio balloon,
as well as multiple fixes and cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: don't hold onto file pointer for VHOST_SET_LOG_FD
vhost: don't hold onto file pointer for VHOST_SET_VRING_ERR
vhost: don't hold onto file pointer for VHOST_SET_VRING_CALL
ringtest: ring.c malloc & memset to calloc
virtio_vop: don't kfree device on register failure
virtio_pci: don't kfree device on register failure
virtio: split device_register into device_initialize and device_add
vhost: remove unused lock check flag in vhost_dev_cleanup()
vhost: Remove the unused variable.
virtio_blk: print capacity at probe time
virtio: make VIRTIO a menuconfig to ease disabling it all
virtio/ringtest: virtio_ring: fix up need_event math
virtio/ringtest: fix up need_event math
virtio: virtio_mmio: make of_device_ids const.
firmware: Use PTR_ERR_OR_ZERO()
virtio-mmio: Use PTR_ERR_OR_ZERO()
vhost/scsi: Improve a size determination in four functions
virtio_balloon: include disk/file caches memory statistics
Chuck Lever [Fri, 2 Feb 2018 19:28:59 +0000 (14:28 -0500)]
svcrdma: Fix Read chunk round-up
A single NFSv4 WRITE compound can often have three operations:
PUTFH, WRITE, then GETATTR.
When the WRITE payload is sent in a Read chunk, the client places
the GETATTR in the inline part of the RPC/RDMA message, just after
the WRITE operation (sans payload). The position value in the Read
chunk enables the receiver to insert the Read chunk at the correct
place in the received XDR stream; that is between the WRITE and
GETATTR.
According to RFC 8166, an NFS/RDMA client does not have to add XDR
round-up to the Read chunk that carries the WRITE payload. The
receiver adds XDR round-up padding if it is absent and the
receiver's XDR decoder requires it to be present.
Commit
193bcb7b3719 ("svcrdma: Populate tail iovec when receiving")
attempted to add support for receiving such a compound so that just
the WRITE payload appears in rq_arg's page list, and the trailing
GETATTR is placed in rq_arg's tail iovec. (TCP just strings the
whole compound into the head iovec and page list, without regard
to the alignment of the WRITE payload).
The server transport logic also had to accommodate the optional XDR
round-up of the Read chunk, which it did simply by lengthening the
tail iovec when round-up was needed. This approach is adequate for
the NFSv2 and NFSv3 WRITE decoders.
Unfortunately it is not sufficient for nfsd4_decode_write. When the
Read chunk length is a couple of bytes less than PAGE_SIZE, the
computation at the end of nfsd4_decode_write allows argp->pagelen to
go negative, which breaks the logic in read_buf that looks for the
tail iovec.
The result is that a WRITE operation whose payload length is just
less than a multiple of a page succeeds, but the subsequent GETATTR
in the same compound fails with NFS4ERR_OP_ILLEGAL because the XDR
decoder can't find it. Clients ignore the error, but they must
update their attribute cache via a separate round trip.
As nfsd4_decode_write appears to expect the payload itself to always
have appropriate XDR round-up, have svc_rdma_build_normal_read_chunk
add the Read chunk XDR round-up to the page_len rather than
lengthening the tail iovec.
Reported-by: Olga Kornievskaia <kolga@netapp.com>
Fixes:
193bcb7b3719 ("svcrdma: Populate tail iovec when receiving")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Tested-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Arnd Bergmann [Mon, 22 Jan 2018 21:09:12 +0000 (22:09 +0100)]
NFSD: hide unused svcxdr_dupstr()
There is now only one caller left for svcxdr_dupstr() and this is inside
of an #ifdef, so we can get a warning when the option is disabled:
fs/nfsd/nfs4xdr.c:241:1: error: 'svcxdr_dupstr' defined but not used [-Werror=unused-function]
This changes the remaining caller to use a nicer IS_ENABLED() check,
which lets the compiler drop the unused code silently.
Fixes:
e40d99e6183e ("NFSD: Clean up symlink argument XDR decoders")
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Amir Goldstein [Wed, 3 Jan 2018 15:14:35 +0000 (17:14 +0200)]
nfsd: store stat times in fill_pre_wcc() instead of inode times
The time values in stat and inode may differ for overlayfs and stat time
values are the correct ones to use. This is also consistent with the fact
that fill_post_wcc() also stores stat time values.
This means introducing a stat call that could fail, where previously we
were just copying values out of the inode. To be conservative about
changing behavior, we fall back to copying values out of the inode in
the error case. It might be better just to clear fh_pre_saved (though
note the BUG_ON in set_change_info).
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Amir Goldstein [Wed, 3 Jan 2018 15:14:34 +0000 (17:14 +0200)]
nfsd: encode stat->mtime for getattr instead of inode->i_mtime
The values of stat->mtime and inode->i_mtime may differ for overlayfs
and stat->mtime is the correct value to use when encoding getattr.
This is also consistent with the fact that other attr times are also
encoded from stat values.
Both callers of lease_get_mtime() already have the value of stat->mtime,
so the only needed change is that lease_get_mtime() will not overwrite
this value with inode->i_mtime in case the inode does not have an
exclusive lease.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
J. Bruce Fields [Wed, 15 Nov 2017 17:30:27 +0000 (12:30 -0500)]
nfsd: return RESOURCE not GARBAGE_ARGS on too many ops
A client that sends more than a hundred ops in a single compound
currently gets an rpc-level GARBAGE_ARGS error.
It would be more helpful to return NFS4ERR_RESOURCE, since that gives
the client a better idea how to recover (for example by splitting up the
compound into smaller compounds).
This is all a bit academic since we've never actually seen a reason for
clients to send such long compounds, but we may as well fix it.
While we're there, just use NFSD4_MAX_OPS_PER_COMPOUND == 16, the
constant we already use in the 4.1 case, instead of hard-coding 100.
Chances anyone actually uses even 16 ops per compound are small enough
that I think there's a neglible risk or any regression.
This fixes pynfs test COMP6.
Reported-by: "Lu, Xinyu" <luxy.fnst@cn.fujitsu.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Linus Torvalds [Thu, 8 Feb 2018 18:36:05 +0000 (10:36 -0800)]
Merge tags 'cris-for-4.16' and 'cris-for-4.16-urgent' of git://git./linux/kernel/git/jesper/cris
Pull CRIS updates and fixes from Jesper Nilsson:
- a small fix for some conflicting symbols, aligning CRIS with other
platforms.
- fix build breakage regression for all CRIS SoCs. The main Makefile
for the CRIS port was overzealously scrubbed in 4.15-rc3.
* tag 'cris-for-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: Fix conflicting types for _etext, _edata, _end
* tag 'cris-for-4.16-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
CRIS: Restore mistakenly cleared kernel Makefile
Kalle Valo [Thu, 8 Feb 2018 17:28:49 +0000 (19:28 +0200)]
Merge ath-current from git://git./linux/kernel/git/kvalo/ath.git
ath.git fixes for 4.16. Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
Steven Rostedt (VMware) [Tue, 6 Feb 2018 22:28:36 +0000 (17:28 -0500)]
selftests/ftrace: Add more tests for removing of function probes
Al Viro discovered a bug in the removing of function probes where if it had
a '*' at the beginning, it would fail to find any matches. That is, because
it reset the glob search string to the the initial string with a "MATCH_END"
type, instead of skipping the wildcard "*" it included it, where it would
not match any functions because "*" was being treated as a normal character
and not a wildcard one.
Link: http://lkml.kernel.org/r/20180127031706.GE13338@ZenIV.linux.org.uk
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Tue, 6 Feb 2018 22:19:03 +0000 (17:19 -0500)]
selftests/ftrace: Add some missing glob checks
Al Viro discovered a bug in the glob ftrace filtering code where "*a*b" is
treated the same as "a*b", and functions that would be selected by "*a*b"
but not "a*b" are not selected with "*a*b".
Add tests for patterns "*a*b" and "a*b*" to the glob selftest.
Link: http://lkml.kernel.org/r/20180127170748.GF13338@ZenIV.linux.org.uk
Cc: Shuah Khan <shuah@kernel.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Tue, 6 Feb 2018 22:15:02 +0000 (17:15 -0500)]
selftests/ftrace: Have reset_ftrace_filter handle multiple instances
If a probe is attached to a static function that is in multiple files with
the same name, removing it by name will remove all instances:
# grep jump_label_unlock set_ftrace_filter
jump_label_unlock:traceoff:unlimited
jump_label_unlock:traceoff:unlimited
# echo '!jump_label_unlock:traceoff' >> set_ftrace_filter
# grep jump_label_unlock set_ftrace_filter
#
But the loop in reset_ftrace_filter will try to remove multiple instances
multiple times. If this happens the second time will error and cause the
test to fail.
At each iteration of the loop, check to see if the probe being removed still
exists.
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Tue, 6 Feb 2018 22:10:12 +0000 (17:10 -0500)]
selftests/ftrace: Have reset_ftrace_filter handle modules
If a function probe in set_ftrace_filter belongs to a module, it will
contain the module name. Like:
wmi_query_block [wmi]:traceoff:unlimited
But writing:
'!wmi_query_block [wmi]:traceoff' > set_ftrace_filter
will cause an error. We still need to write:
'!wmi_query_block:traceoff' > set_ftrace_filter
Cc: Shuah Khan <shuah@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Tue, 6 Feb 2018 03:18:11 +0000 (22:18 -0500)]
tracing: Fix parsing of globs with a wildcard at the beginning
Al Viro reported:
For substring - sure, but what about something like "*a*b" and "a*b"?
AFAICS, filter_parse_regex() ends up with identical results in both
cases - MATCH_GLOB and *search = "a*b". And no way for the caller
to tell one from another.
Testing this with the following:
# cd /sys/kernel/tracing
# echo '*raw*lock' > set_ftrace_filter
bash: echo: write error: Invalid argument
With this patch:
# echo '*raw*lock' > set_ftrace_filter
# cat set_ftrace_filter
_raw_read_trylock
_raw_write_trylock
_raw_read_unlock
_raw_spin_unlock
_raw_write_unlock
_raw_spin_trylock
_raw_spin_lock
_raw_write_lock
_raw_read_lock
Al recommended not setting the search buffer to skip the first '*' unless we
know we are not using MATCH_GLOB. This implements his suggested logic.
Link: http://lkml.kernel.org/r/20180127170748.GF13338@ZenIV.linux.org.uk
Cc: stable@vger.kernel.org
Fixes:
60f1d5e3bac44 ("ftrace: Support full glob matching")
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Suggsted-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Steven Rostedt (VMware) [Tue, 6 Feb 2018 03:05:31 +0000 (22:05 -0500)]
ftrace: Remove incorrect setting of glob search field
__unregister_ftrace_function_probe() will incorrectly parse the glob filter
because it resets the search variable that was setup by filter_parse_regex().
Al Viro reported this:
After that call of filter_parse_regex() we could have func_g.search not
equal to glob only if glob started with '!' or '*'. In the former case
we would've buggered off with -EINVAL (not = 1). In the latter we
would've set func_g.search equal to glob + 1, calculated the length of
that thing in func_g.len and proceeded to reset func_g.search back to
glob.
Suppose the glob is e.g. *foo*. We end up with
func_g.type = MATCH_MIDDLE_ONLY;
func_g.len = 3;
func_g.search = "*foo";
Feeding that to ftrace_match_record() will not do anything sane - we
will be looking for names containing "*foo" (->len is ignored for that
one).
Link: http://lkml.kernel.org/r/20180127031706.GE13338@ZenIV.linux.org.uk
Cc: stable@vger.kernel.org
Fixes:
3ba009297149f ("ftrace: Introduce ftrace_glob structure")
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
David S. Miller [Thu, 8 Feb 2018 15:01:28 +0000 (10:01 -0500)]
Merge branch 'nfp-fix-disabling-TC-offloads-in-flower-max-TSO-segs-and-module-version'
Jakub Kicinski says:
====================
nfp: fix disabling TC offloads in flower, max TSO segs and module version
This set corrects the way nfp deals with the NETIF_F_HW_TC flag.
It has slipped the review that flower offload does not currently
refuse disabling this flag when filter offload is active.
nfp's flower offload does not actually keep track of how many filters
for each port are offloaded. The accounting of the number of filters
is added to the nfp core structures, and BPF moved to use these
structures as well.
If users are allowed to disable TC offloads while filters are active,
not only is it incorrect behaviour, but actually the NFP will never
be told to remove the flows, leading to use-after-free when stats
arrive.
Fourth patch makes sure we declare the max number of TSO segments.
FW should drop longer packets cleanly (otherwise this would be a
security problem for untrusted VFs) but dropping longer TSO frames
is not nice and driver should prevent them from being generated.
Last small addition populates MODULE_VERSION with kernel version.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 8 Feb 2018 04:55:26 +0000 (20:55 -0800)]
nfp: populate MODULE_VERSION
DKMS and similar out-of-tree module replacement services use
module version to make sure the out-of-tree software is not
older than the module shipped with the kernel. We use the
kernel version in ethtool -i output, put it into MODULE_VERSION
as well.
Reported-by: Jan Gutter <jan.gutter@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 8 Feb 2018 04:55:25 +0000 (20:55 -0800)]
nfp: limit the number of TSO segments
Most FWs limit the number of TSO segments a frame can produce
to 64. This is for fairness and efficiency (of FW datapath)
reasons. If a frame with larger number of segments is submitted
the FW will drop it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 8 Feb 2018 04:55:24 +0000 (20:55 -0800)]
nfp: forbid disabling hw-tc-offload on representors while offload active
All netdevs which can accept TC offloads must implement
.ndo_set_features(). nfp_reprs currently do not do that, which
means hw-tc-offload can be turned on and off even when offloads
are active.
Whether the offloads are active is really a question to nfp_ports,
so remove the per-app tc_busy callback indirection thing, and
simply count the number of offloaded items in nfp_port structure.
Fixes:
8a2768732a4d ("nfp: provide infrastructure for offloading flower based TC filters")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 8 Feb 2018 04:55:23 +0000 (20:55 -0800)]
nfp: don't advertise hw-tc-offload on non-port netdevs
nfp_port is a structure which represents an ASIC port, both
PCIe vNIC (on a PF or a VF) or the external MAC port. vNIC
netdev (struct nfp_net) and pure representor netdev (struct
nfp_repr) both have a pointer to this structure. nfp_reprs
always have a port associated. nfp_nets, however, only represent
a device port in legacy mode, where they are considered the
MAC port. In switchdev mode they are just the CPU's side of
the PCIe link.
By definition TC offloads only apply to device ports. Don't
set the flag on vNICs without a port (i.e. in switchdev mode).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Thu, 8 Feb 2018 04:55:22 +0000 (20:55 -0800)]
nfp: bpf: require ETH table
Upcoming changes will require all netdevs supporting TC offloads
to have a full struct nfp_port. Require those for BPF offload.
The operation without management FW reporting information about
Ethernet ports is something we only support for very old and very
basic NIC firmwares anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>