Jason Gerecke [Tue, 12 Jun 2018 20:42:46 +0000 (13:42 -0700)]
HID: wacom: Correct logical maximum Y for 2nd-gen Intuos Pro large
commit
d471b6b22d37bf9928c6d0202bdaaf76583b8b61 upstream.
The HID descriptor for the 2nd-gen Intuos Pro large (PTH-860) contains
a typo which defines an incorrect logical maximum Y value. This causes
a small portion of the bottom of the tablet to become unusable (both
because the area is below the "bottom" of the tablet and because
'wacom_wac_event' ignores out-of-range values). It also results in a
skewed aspect ratio.
To fix this, we add a quirk to 'wacom_usage_mapping' which overwrites
the data with the correct value.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
CC: stable@vger.kernel.org # v4.10+
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even Xu [Thu, 11 Feb 2016 20:11:34 +0000 (04:11 +0800)]
HID: intel_ish-hid: ipc: register more pm callbacks to support hibernation
commit
ebeaa367548e9e92dd9374b9464ff6e7d157117b upstream.
Current ISH driver only registers suspend/resume PM callbacks which don't
support hibernation (suspend to disk). Basically after hiberation, the ISH
can't resume properly and user may not see sensor events (for example: screen
rotation may not work).
User will not see a crash or panic or anything except the following message
in log:
hid-sensor-hub 001F:8086:22D8.0001: timeout waiting for response from ISHTP device
So this patch adds support for S4/hiberbation to ISH by using the
SIMPLE_DEV_PM_OPS() MACRO instead of struct dev_pm_ops directly. The suspend
and resume functions will now be used for both suspend to RAM and hibernation.
If power management is disabled, SIMPLE_DEV_PM_OPS will do nothing, the suspend
and resume related functions won't be used, so mark them as __maybe_unused to
clarify that this is the intended behavior, and remove #ifdefs for power
management.
Cc: stable@vger.kernel.org
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Brandenburg [Thu, 31 May 2018 16:37:00 +0000 (16:37 +0000)]
orangefs: report attributes_mask and attributes for statx
commit
7f54910fa8dfe504f2e1563f4f6ddc3294dfbf3a upstream.
OrangeFS formerly failed to set attributes_mask with the result that
software could not see immutable and append flags present in the
filesystem.
Reported-by: Becky Ligon <ligon@clemson.edu>
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Fixes:
68a24a6cc4a6 ("orangefs: implement statx")
Cc: stable@vger.kernel.org
Cc: hubcap@omnibond.com
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Martin Brandenburg [Thu, 31 May 2018 16:36:58 +0000 (16:36 +0000)]
orangefs: set i_size on new symlink
commit
f6a4b4c9d07dda90c7c29dae96d6119ac6425dca upstream.
As long as a symlink inode remains in-core, the destination (and
therefore size) will not be re-fetched from the server, as it cannot
change. The original implementation of the attribute cache assumed that
setting the expiry time in the past was sufficient to cause a re-fetch
of all attributes on the next getattr. That does not work in this case.
The bug manifested itself as follows. When the command sequence
touch foo; ln -s foo bar; ls -l bar
is run, the output was
lrwxrwxrwx. 1 fedora fedora 4906 Apr 24 19:10 bar -> foo
However, after a re-mount, ls -l bar produces
lrwxrwxrwx. 1 fedora fedora 3 Apr 24 19:10 bar -> foo
After this commit, even before a re-mount, the output is
lrwxrwxrwx. 1 fedora fedora 3 Apr 24 19:10 bar -> foo
Reported-by: Becky Ligon <ligon@clemson.edu>
Signed-off-by: Martin Brandenburg <martin@omnibond.com>
Fixes:
71680c18c8f2 ("orangefs: Cache getattr results.")
Cc: stable@vger.kernel.org
Cc: hubcap@omnibond.com
Signed-off-by: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luca Coelho [Tue, 13 Feb 2018 09:09:40 +0000 (11:09 +0200)]
iwlwifi: fw: harden page loading code
commit
9039d985811d5b109b58b202b7594fd24e433fed upstream.
The page loading code trusts the data provided in the firmware images
a bit too much and may cause a buffer overflow or copy unknown data if
the block sizes don't match what we expect.
To prevent potential problems, harden the code by checking if the
sizes we are copying are what we expect.
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Luck [Fri, 8 Jun 2018 16:07:32 +0000 (09:07 -0700)]
x86/intel_rdt: Enable CMT and MBM on new Skylake stepping
commit
1d9f3e20a56d33e55748552aeec597f58542f92d upstream.
New stepping of Skylake has fixes for cache occupancy and memory
bandwidth monitoring.
Update the code to enable these by default on newer steppings.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: stable@vger.kernel.org # v4.14
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Link: https://lkml.kernel.org/r/20180608160732.9842-1-tony.luck@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Potyra [Wed, 2 May 2018 08:55:31 +0000 (10:55 +0200)]
w1: mxc_w1: Enable clock before calling clk_get_rate() on it
commit
955bc61328dc0a297fb3baccd84e9d3aee501ed8 upstream.
According to the API, you may only call clk_get_rate() after actually
enabling it.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes:
a5fd9139f74c ("w1: add 1-wire master driver for i.MX27 / i.MX31")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Thu, 31 May 2018 11:21:07 +0000 (13:21 +0200)]
libata: Drop SanDisk SD7UB3Q*G1001 NOLPM quirk
commit
2cfce3a86b64b53f0a70e92a6a659c720c319b45 upstream.
Commit
184add2ca23c ("libata: Apply NOLPM quirk for SanDisk
SD7UB3Q*G1001 SSDs") disabled LPM for SanDisk SD7UB3Q*G1001 SSDs.
This has lead to several reports of users of that SSD where LPM
was working fine and who know have a significantly increased idle
power consumption on their laptops.
Likely there is another problem on the T450s from the original
reporter which gets exposed by the uncore reaching deeper sleep
states (higher PC-states) due to LPM being enabled. The problem as
reported, a hardfreeze about once a day, already did not sound like
it would be caused by LPM and the reports of the SSD working fine
confirm this. The original reporter is ok with dropping the quirk.
A X250 user has reported the same hard freeze problem and for him
the problem went away after unrelated updates, I suspect some GPU
driver stack changes fixed things.
TL;DR: The original reporters problem were triggered by LPM but not
an LPM issue, so drop the quirk for the SSD in question.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1583207
Cc: stable@vger.kernel.org
Cc: Richard W.M. Jones <rjones@redhat.com>
Cc: Lorenzo Dalrio <lorenzo.dalrio@gmail.com>
Reported-by: Lorenzo Dalrio <lorenzo.dalrio@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "Richard W.M. Jones" <rjones@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 29 May 2018 09:13:24 +0000 (12:13 +0300)]
libata: zpodd: small read overflow in eject_tray()
commit
18c9a99bce2a57dfd7e881658703b5d7469cc7b9 upstream.
We read from the cdb[] buffer in ata_exec_internal_sg(). It has to be
ATAPI_CDB_LEN (16) bytes long, but this buffer is only 12 bytes.
Fixes:
213342053db5 ("libata: handle power transition of ODD")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chen Yu [Fri, 8 Jun 2018 01:07:33 +0000 (09:07 +0800)]
cpufreq: governors: Fix long idle detection logic in load calculation
commit
7592019634f8473f0b0973ce79297183077bdbc2 upstream.
According to current code implementation, detecting the long
idle period is done by checking if the interval between two
adjacent utilization update handlers is long enough. Although
this mechanism can detect if the idle period is long enough
(no utilization hooks invoked during idle period), it might
not cover a corner case: if the task has occupied the CPU
for too long which causes no context switches during that
period, then no utilization handler will be launched until this
high prio task is scheduled out. As a result, the idle_periods
field might be calculated incorrectly because it regards the
100% load as 0% and makes the conservative governor who uses
this field confusing.
Change the detection to compare the idle_time with sampling_rate
directly.
Reported-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tao Wang [Sat, 26 May 2018 07:16:48 +0000 (15:16 +0800)]
cpufreq: Fix new policy initialization during limits updates via sysfs
commit
c7d1f119c48f64bebf0fa1e326af577c6152fe30 upstream.
If the policy limits are updated via cpufreq_update_policy() and
subsequently via sysfs, the limits stored in user_policy may be
set incorrectly.
For example, if both min and max are set via sysfs to the maximum
available frequency, user_policy.min and user_policy.max will also
be the maximum. If a policy notifier triggered by
cpufreq_update_policy() lowers both the min and the max at this
point, that change is not reflected by the user_policy limits, so
if the max is updated again via sysfs to the same lower value,
then user_policy.max will be lower than user_policy.min which
shouldn't happen. In particular, if one of the policy CPUs is
then taken offline and back online, cpufreq_set_policy() will
fail for it due to a failing limits check.
To prevent that from happening, initialize the min and max fields
of the new_policy object to the ones stored in user_policy that
were previously set via sysfs.
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ]
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Wed, 23 May 2018 17:56:32 +0000 (10:56 -0700)]
bdi: Move cgroup bdi_writeback to a dedicated low concurrency workqueue
commit
f183464684190bacbfb14623bd3e4e51b7575b4c upstream.
From
0aa2e9b921d6db71150633ff290199554f0842a8 Mon Sep 17 00:00:00 2001
From: Tejun Heo <tj@kernel.org>
Date: Wed, 23 May 2018 10:29:00 -0700
cgwb_release() punts the actual release to cgwb_release_workfn() on
system_wq. Depending on the number of cgroups or block devices, there
can be a lot of cgwb_release_workfn() in flight at the same time.
We're periodically seeing close to 256 kworkers getting stuck with the
following stack trace and overtime the entire system gets stuck.
[<
ffffffff810ee40c>] _synchronize_rcu_expedited.constprop.72+0x2fc/0x330
[<
ffffffff810ee634>] synchronize_rcu_expedited+0x24/0x30
[<
ffffffff811ccf23>] bdi_unregister+0x53/0x290
[<
ffffffff811cd1e9>] release_bdi+0x89/0xc0
[<
ffffffff811cd645>] wb_exit+0x85/0xa0
[<
ffffffff811cdc84>] cgwb_release_workfn+0x54/0xb0
[<
ffffffff810a68d0>] process_one_work+0x150/0x410
[<
ffffffff810a71fd>] worker_thread+0x6d/0x520
[<
ffffffff810ad3dc>] kthread+0x12c/0x160
[<
ffffffff81969019>] ret_from_fork+0x29/0x40
[<
ffffffffffffffff>] 0xffffffffffffffff
The events leading to the lockup are...
1. A lot of cgwb_release_workfn() is queued at the same time and all
system_wq kworkers are assigned to execute them.
2. They all end up calling synchronize_rcu_expedited(). One of them
wins and tries to perform the expedited synchronization.
3. However, that invovles queueing rcu_exp_work to system_wq and
waiting for it. Because #1 is holding all available kworkers on
system_wq, rcu_exp_work can't be executed. cgwb_release_workfn()
is waiting for synchronize_rcu_expedited() which in turn is waiting
for cgwb_release_workfn() to free up some of the kworkers.
We shouldn't be scheduling hundreds of cgwb_release_workfn() at the
same time. There's nothing to be gained from that. This patch
updates cgwb release path to use a dedicated percpu workqueue with
@max_active of 1.
While this resolves the problem at hand, it might be a good idea to
isolate rcu_exp_work to its own workqueue too as it can be used from
various paths and is prone to this sort of indirect A-A deadlocks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Pen [Sun, 10 Jun 2018 20:38:24 +0000 (22:38 +0200)]
blk-mq: reinit q->tag_set_list entry only after grace period
commit
a347c7ad8edf4c5685154f3fdc3c12fc1db800ba upstream.
It is not allowed to reinit q->tag_set_list list entry while RCU grace
period has not completed yet, otherwise the following soft lockup in
blk_mq_sched_restart() happens:
[ 1064.252652] watchdog: BUG: soft lockup - CPU#12 stuck for 23s! [fio:9270]
[ 1064.254445] task:
ffff99b912e8b900 task.stack:
ffffa6d54c758000
[ 1064.254613] RIP: 0010:blk_mq_sched_restart+0x96/0x150
[ 1064.256510] Call Trace:
[ 1064.256664] <IRQ>
[ 1064.256824] blk_mq_free_request+0xea/0x100
[ 1064.256987] msg_io_conf+0x59/0xd0 [ibnbd_client]
[ 1064.257175] complete_rdma_req+0xf2/0x230 [ibtrs_client]
[ 1064.257340] ? ibtrs_post_recv_empty+0x4d/0x70 [ibtrs_core]
[ 1064.257502] ibtrs_clt_rdma_done+0xd1/0x1e0 [ibtrs_client]
[ 1064.257669] ib_create_qp+0x321/0x380 [ib_core]
[ 1064.257841] ib_process_cq_direct+0xbd/0x120 [ib_core]
[ 1064.258007] irq_poll_softirq+0xb7/0xe0
[ 1064.258165] __do_softirq+0x106/0x2a2
[ 1064.258328] irq_exit+0x92/0xa0
[ 1064.258509] do_IRQ+0x4a/0xd0
[ 1064.258660] common_interrupt+0x7a/0x7a
[ 1064.258818] </IRQ>
Meanwhile another context frees other queue but with the same set of
shared tags:
[ 1288.201183] INFO: task bash:5910 blocked for more than 180 seconds.
[ 1288.201833] bash D 0 5910 5820 0x00000000
[ 1288.202016] Call Trace:
[ 1288.202315] schedule+0x32/0x80
[ 1288.202462] schedule_timeout+0x1e5/0x380
[ 1288.203838] wait_for_completion+0xb0/0x120
[ 1288.204137] __wait_rcu_gp+0x125/0x160
[ 1288.204287] synchronize_sched+0x6e/0x80
[ 1288.204770] blk_mq_free_queue+0x74/0xe0
[ 1288.204922] blk_cleanup_queue+0xc7/0x110
[ 1288.205073] ibnbd_clt_unmap_device+0x1bc/0x280 [ibnbd_client]
[ 1288.205389] ibnbd_clt_unmap_dev_store+0x169/0x1f0 [ibnbd_client]
[ 1288.205548] kernfs_fop_write+0x109/0x180
[ 1288.206328] vfs_write+0xb3/0x1a0
[ 1288.206476] SyS_write+0x52/0xc0
[ 1288.206624] do_syscall_64+0x68/0x1d0
[ 1288.206774] entry_SYSCALL_64_after_hwframe+0x3d/0xa2
What happened is the following:
1. There are several MQ queues with shared tags.
2. One queue is about to be freed and now task is in
blk_mq_del_queue_tag_set().
3. Other CPU is in blk_mq_sched_restart() and loops over all queues in
tag list in order to find hctx to restart.
Because linked list entry was modified in blk_mq_del_queue_tag_set()
without proper waiting for a grace period, blk_mq_sched_restart()
never ends, spining in list_for_each_entry_rcu_rr(), thus soft lockup.
Fix is simple: reinit list entry after an RCU grace period elapsed.
Fixes: Fixes:
705cda97ee3a ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Cc: stable@vger.kernel.org
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: linux-block@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Wed, 16 May 2018 18:51:19 +0000 (14:51 -0400)]
nbd: use bd_set_size when updating disk size
commit
9e2b19675d1338d2a38e99194756f2db44a081df upstream.
When we stopped relying on the bdev everywhere I broke updating the
block device size on the fly, which ceph relies on. We can't just do
set_capacity, we also have to do bd_set_size so things like parted will
notice the device size change.
Fixes: 29eaadc ("nbd: stop using the bdev everywhere")
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Wed, 16 May 2018 18:51:18 +0000 (14:51 -0400)]
nbd: update size when connected
commit
c3f7c9397609705ef848cc98a5fb429b3e90c3c4 upstream.
I messed up changing the size of an NBD device while it was connected by
not actually updating the device or doing the uevent. Fix this by
updating everything if we're connected and we change the size.
cc: stable@vger.kernel.org
Fixes: 639812a ("nbd: don't set the device size until we're connected")
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Josef Bacik [Wed, 16 May 2018 18:51:17 +0000 (14:51 -0400)]
nbd: fix nbd device deletion
commit
8364da4751cf22201d74933d5e634176f44ed407 upstream.
This fixes a use after free bug, we shouldn't be doing disk->queue right
after we do del_gendisk(disk). Save the queue and do the cleanup after
the del_gendisk.
Fixes:
c6a4759ea0c9 ("nbd: add device refcounting")
cc: stable@vger.kernel.org
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shirish Pargaonkar [Mon, 4 Jun 2018 11:46:22 +0000 (06:46 -0500)]
cifs: For SMB2 security informaion query, check for minimum sized security descriptor instead of sizeof FileAllInformation class
commit
ee25c6dd7b05113783ce1f4fab6b30fc00d29b8d upstream.
Validate_buf () function checks for an expected minimum sized response
passed to query_info() function.
For security information, the size of a security descriptor can be
smaller (one subauthority, no ACEs) than the size of the structure
that defines FileInfoClass of FileAllInformation.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199725
Cc: <stable@vger.kernel.org>
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Noah Morrison <noah.morrison@rubrik.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Syms [Thu, 24 May 2018 08:47:31 +0000 (09:47 +0100)]
CIFS:
511c54a2f69195b28afb9dd119f03787b1625bb4 adds a check for session expiry
commit
d81243c697ffc71f983736e7da2db31a8be0001f upstream.
Handle this additional status in the same way as SESSION_EXPIRED.
Signed-off-by: Mark Syms <mark.syms@citrix.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Thu, 31 May 2018 20:19:25 +0000 (15:19 -0500)]
smb3: on reconnect set PreviousSessionId field
commit
b2adf22fdfba85a6701c481faccdbbb3a418ccfc upstream.
The server detects reconnect by the (non-zero) value in PreviousSessionId
of SMB2/SMB3 SessionSetup request, but this behavior regressed due
to commit
166cea4dc3a4f66f020cfb9286225ecd228ab61d
("SMB2: Separate RawNTLMSSP authentication from SMB2_sess_setup")
CC: Stable <stable@vger.kernel.org>
CC: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve French [Sat, 19 May 2018 07:04:55 +0000 (02:04 -0500)]
smb3: fix various xid leaks
commit
cfe89091644c441a1ade6dae6d2e47b715648615 upstream.
Fix a few cases where we were not freeing the xid which led to
active requests being non-zero at unmount time.
Signed-off-by: Steve French <smfrench@gmail.com>
CC: Stable <stable@vger.kernel.org>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Luck [Fri, 27 Apr 2018 16:37:08 +0000 (09:37 -0700)]
x86/MCE: Fix stack out-of-bounds write in mce-inject.c: Flags_read()
commit
985c78d3ff8e9c74450fa2bb08eb55e680d999ca upstream.
Each of the strings that we want to put into the buf[MAX_FLAG_OPT_SIZE]
in flags_read() is two characters long. But the sprintf() adds
a trailing newline and will add a terminating NUL byte. So
MAX_FLAG_OPT_SIZE needs to be 4.
sprintf() calls vsnprintf() and *that* does return:
" * The return value is the number of characters which would
* be generated for the given input, excluding the trailing
* '\0', as per ISO C99."
Note the "excluding".
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20180427163707.ktaiysvbk3yhk4wm@agluck-desk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dennis Wassenberg [Tue, 12 Jun 2018 05:11:11 +0000 (07:11 +0200)]
ALSA: hda: add dock and led support for HP ProBook 640 G4
commit
7eef32c1ef895a3a96463f9cbd04203007cd5555 upstream.
This patch adds missing initialisation for HP 2013 UltraSlim Dock
Line-In/Out PINs and activates keyboard mute/micmute leds
for HP ProBook 640 G4
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dennis Wassenberg [Tue, 12 Jun 2018 05:10:59 +0000 (07:10 +0200)]
ALSA: hda: add dock and led support for HP EliteBook 830 G5
commit
2861751f67b91e1d24e68010ced96614fb3140f4 upstream.
This patch adds missing initialisation for HP 2013 UltraSlim Dock
Line-In/Out PINs and activates keyboard mute/micmute leds
for HP EliteBook 830 G5
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bo Chen [Thu, 31 May 2018 22:35:18 +0000 (15:35 -0700)]
ALSA: hda - Handle kzalloc() failure in snd_hda_attach_pcm_stream()
commit
a3aa60d511746bd6c0d0366d4eb90a7998bcde8b upstream.
When 'kzalloc()' fails in 'snd_hda_attach_pcm_stream()', a new pcm instance is
created without setting its operators via 'snd_pcm_set_ops()'. Following
operations on the new pcm instance can trigger kernel null pointer dereferences
and cause kernel oops.
This bug was found with my work on building a gray-box fault-injection tool for
linux-kernel-module binaries. A kernel null pointer dereference was confirmed
from line 'substream->ops->open()' in function 'snd_pcm_open_substream()' in
file 'sound/core/pcm_native.c'.
This patch fixes the bug by calling 'snd_device_free()' in the error handling
path of 'kzalloc()', which removes the new pcm instance from the snd card before
returns with an error code.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Fri, 18 May 2018 10:14:32 +0000 (12:14 +0200)]
ALSA: hda/conexant - Add fixup for HP Z2 G4 workstation
commit
f16041df4c360eccacfe90f96673b37829e4c959 upstream.
HP Z2 G4 requires the same workaround as other HP machines that have
no mic-pin detection.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hui Wang [Wed, 30 May 2018 04:33:07 +0000 (12:33 +0800)]
ALSA: hda/realtek - Enable mic-mute hotkey for several Lenovo AIOs
commit
986376b68dcc95bb7df60ad30c2353c1f7578fa5 upstream.
We have several Lenovo AIOs like M810z, M820z and M920z, they have
the same design for mic-mute hotkey and led and they use the same
codec with the same pin configuration, so use the pin conf table to
apply fix to all of them.
Fixes:
29693efcea0f ("ALSA: hda - Fix micmute hotkey problem for a lenovo AIO machine")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qu Wenruo [Tue, 5 Jun 2018 04:36:56 +0000 (12:36 +0800)]
btrfs: scrub: Don't use inode pages for device replace
commit
ac0b4145d662a3b9e34085dea460fb06ede9b69b upstream.
[BUG]
Btrfs can create compressed extent without checksum (even though it
shouldn't), and if we then try to replace device containing such extent,
the result device will contain all the uncompressed data instead of the
compressed one.
Test case already submitted to fstests:
https://patchwork.kernel.org/patch/
10442353/
[CAUSE]
When handling compressed extent without checksum, device replace will
goe into copy_nocow_pages() function.
In that function, btrfs will get all inodes referring to this data
extents and then use find_or_create_page() to get pages direct from that
inode.
The problem here is, pages directly from inode are always uncompressed.
And for compressed data extent, they mismatch with on-disk data.
Thus this leads to corrupted compressed data extent written to replace
device.
[FIX]
In this attempt, we could just remove the "optimization" branch, and let
unified scrub_pages() to handle it.
Although scrub_pages() won't bother reusing page cache, it will be a
little slower, but it does the correct csum checking and won't cause
such data corruption caused by "optimization".
Note about the fix: this is the minimal fix that can be backported to
older stable trees without conflicts. The whole callchain from
copy_nocow_pages() can be deleted, and will be in followup patches.
Fixes:
ff023aac3119 ("Btrfs: add code to scrub to copy read data to another disk")
CC: stable@vger.kernel.org # 4.4+
Reported-by: James Harvey <jamespharvey20@gmail.com>
Reviewed-by: James Harvey <jamespharvey20@gmail.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
[ remove code removal, add note why ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Su Yue [Wed, 30 May 2018 08:48:56 +0000 (16:48 +0800)]
btrfs: return error value if create_io_em failed in cow_file_range
commit
090a127afa8f73e9618d4058d6755f7ec7453dd6 upstream.
In cow_file_range(), create_io_em() may fail, but its return value is
not recorded. Then return value may be 0 even it failed which is a
wrong behavior.
Let cow_file_range() return PTR_ERR(em) if create_io_em() failed.
Fixes:
6f9994dbabe5 ("Btrfs: create a helper to create em for IO")
CC: stable@vger.kernel.org # 4.11+
Signed-off-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omar Sandoval [Tue, 22 May 2018 22:44:01 +0000 (15:44 -0700)]
Btrfs: fix memory and mount leak in btrfs_ioctl_rm_dev_v2()
commit
fd4e994bd1f9dc9628e168a7f619bf69f6984635 upstream.
If we have invalid flags set, when we error out we must drop our writer
counter and free the buffer we allocated for the arguments. This bug is
trivially reproduced with the following program on 4.7+:
#include <fcntl.h>
#include <stdint.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <sys/stat.h>
#include <sys/types.h>
#include <linux/btrfs.h>
#include <linux/btrfs_tree.h>
int main(int argc, char **argv)
{
struct btrfs_ioctl_vol_args_v2 vol_args = {
.flags = UINT64_MAX,
};
int ret;
int fd;
if (argc != 2) {
fprintf(stderr, "usage: %s PATH\n", argv[0]);
return EXIT_FAILURE;
}
fd = open(argv[1], O_WRONLY);
if (fd == -1) {
perror("open");
return EXIT_FAILURE;
}
ret = ioctl(fd, BTRFS_IOC_RM_DEV_V2, &vol_args);
if (ret == -1)
perror("ioctl");
close(fd);
return EXIT_SUCCESS;
}
When unmounting the filesystem, we'll hit the
WARN_ON(mnt_get_writers(mnt)) in cleanup_mnt() and also may prevent the
filesystem to be remounted read-only as the writer count will stay
lifted.
Fixes:
6b526ed70cf1 ("btrfs: introduce device delete by devid")
CC: stable@vger.kernel.org # 4.9+
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Su Yue <suy.fnst@cn.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Omar Sandoval [Tue, 22 May 2018 22:02:12 +0000 (15:02 -0700)]
Btrfs: fix clone vs chattr NODATASUM race
commit
b5c40d598f5408bd0ca22dfffa82f03cd9433f23 upstream.
In btrfs_clone_files(), we must check the NODATASUM flag while the
inodes are locked. Otherwise, it's possible that btrfs_ioctl_setflags()
will change the flags after we check and we can end up with a party
checksummed file.
The race window is only a few instructions in size, between the if and
the locks which is:
3834 if (S_ISDIR(src->i_mode) || S_ISDIR(inode->i_mode))
3835 return -EISDIR;
where the setflags must be run and toggle the NODATASUM flag (provided
the file size is 0). The clone will block on the inode lock, segflags
takes the inode lock, changes flags, releases log and clone continues.
Not impossible but still needs a lot of bad luck to hit unintentionally.
Fixes:
0e7b824c4ef9 ("Btrfs: don't make a file partly checksummed through file clone")
CC: stable@vger.kernel.org # 4.4+
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tetsuo Handa [Mon, 7 May 2018 10:10:31 +0000 (19:10 +0900)]
driver core: Don't ignore class_dir_create_and_add() failure.
commit
84d0c27d6233a9ba0578b20f5a09701eb66cee42 upstream.
syzbot is hitting WARN() at kernfs_add_one() [1].
This is because kernfs_create_link() is confused by previous device_add()
call which continued without setting dev->kobj.parent field when
get_device_parent() failed by memory allocation fault injection.
Fix this by propagating the error from class_dir_create_and_add() to
the calllers of get_device_parent().
[1] https://syzkaller.appspot.com/bug?id=
fae0fb607989ea744526d1c082a5b8de6529116f
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+df47f81c226b31d89fb1@syzkaller.appspotmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Fri, 25 May 2018 16:51:25 +0000 (12:51 -0400)]
ext4: fix fencepost error in check for inode count overflow during resize
commit
4f2f76f751433908364ccff82f437a57d0e6e9b7 upstream.
ext4_resize_fs() has an off-by-one bug when checking whether growing of
a filesystem will not overflow inode count. As a result it allows a
filesystem with 8192 inodes per group to grow to 64TB which overflows
inode count to 0 and makes filesystem unusable. Fix it.
Cc: stable@vger.kernel.org
Fixes:
3f8a6411fbada1fa482276591e037f3b1adcf55b
Reported-by: Jaco Kroon <jaco@uls.co.za>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Wed, 23 May 2018 15:31:03 +0000 (11:31 -0400)]
ext4: correctly handle a zero-length xattr with a non-zero e_value_offs
commit
8a2b307c21d4b290e3cbe33f768f194286d07c23 upstream.
Ext4 will always create ext4 extended attributes which do not have a
value (where e_value_size is zero) with e_value_offs set to zero. In
most places e_value_offs will not be used in a substantive way if
e_value_size is zero.
There was one exception to this, which is in ext4_xattr_set_entry(),
where if there is a maliciously crafted file system where there is an
extended attribute with e_value_offs is non-zero and e_value_size is
0, the attempt to remove this xattr will result in a negative value
getting passed to memmove, leading to the following sadness:
[ 41.225365] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
[ 44.538641] BUG: unable to handle kernel paging request at
ffff9ec9a3000000
[ 44.538733] IP: __memmove+0x81/0x1a0
[ 44.538755] PGD
1249bd067 P4D
1249bd067 PUD
1249c1067 PMD
80000001230000e1
[ 44.538793] Oops: 0003 [#1] SMP PTI
[ 44.539074] CPU: 0 PID: 1470 Comm: poc Not tainted 4.16.0-rc1+ #1
...
[ 44.539475] Call Trace:
[ 44.539832] ext4_xattr_set_entry+0x9e7/0xf80
...
[ 44.539972] ext4_xattr_block_set+0x212/0xea0
...
[ 44.540041] ext4_xattr_set_handle+0x514/0x610
[ 44.540065] ext4_xattr_set+0x7f/0x120
[ 44.540090] __vfs_removexattr+0x4d/0x60
[ 44.540112] vfs_removexattr+0x75/0xe0
[ 44.540132] removexattr+0x4d/0x80
...
[ 44.540279] path_removexattr+0x91/0xb0
[ 44.540300] SyS_removexattr+0xf/0x20
[ 44.540322] do_syscall_64+0x71/0x120
[ 44.540344] entry_SYSCALL_64_after_hwframe+0x21/0x86
https://bugzilla.kernel.org/show_bug.cgi?id=199347
This addresses CVE-2018-10840.
Reported-by: "Xu, Wen" <wen.xu@gatech.edu>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@kernel.org
Fixes:
dec214d00e0d7 ("ext4: xattr inode deduplication")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Tue, 22 May 2018 21:14:07 +0000 (17:14 -0400)]
ext4: bubble errors from ext4_find_inline_data_nolock() up to ext4_iget()
commit
eb9b5f01c33adebc31cbc236c02695f605b0e417 upstream.
If ext4_find_inline_data_nolock() returns an error it needs to get
reflected up to ext4_iget(). In order to fix this,
ext4_iget_extra_inode() needs to return an error (and not return
void).
This is related to "ext4: do not allow external inodes for inline
data" (which fixes CVE-2018-11412) in that in the errors=continue
case, it would be useful to for userspace to receive an error
indicating that file system is corrupted.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Theodore Ts'o [Tue, 22 May 2018 20:15:24 +0000 (16:15 -0400)]
ext4: do not allow external inodes for inline data
commit
117166efb1ee8f13c38f9e96b258f16d4923f888 upstream.
The inline data feature was implemented before we added support for
external inodes for xattrs. It makes no sense to support that
combination, but the problem is that there are a number of extended
attribute checks that are skipped if e_value_inum is non-zero.
Unfortunately, the inline data code is completely e_value_inum
unaware, and attempts to interpret the xattr fields as if it were an
inline xattr --- at which point, Hilarty Ensues.
This addresses CVE-2018-11412.
https://bugzilla.kernel.org/show_bug.cgi?id=199803
Reported-by: Jann Horn <jannh@google.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Fixes:
e50e5129f384 ("ext4: xattr-in-inode support")
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lukas Czerner [Sun, 13 May 2018 23:28:35 +0000 (19:28 -0400)]
ext4: update mtime in ext4_punch_hole even if no blocks are released
commit
eee597ac931305eff3d3fd1d61d6aae553bc0984 upstream.
Currently in ext4_punch_hole we're going to skip the mtime update if
there are no actual blocks to release. However we've actually modified
the file by zeroing the partial block so the mtime should be updated.
Moreover the sync and datasync handling is skipped as well, which is
also wrong. Fix it.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Joe Habermann <joe.habermann@quantum.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kara [Sat, 12 May 2018 23:55:00 +0000 (19:55 -0400)]
ext4: fix hole length detection in ext4_ind_map_blocks()
commit
2ee3ee06a8fd792765fa3267ddf928997797eec5 upstream.
When ext4_ind_map_blocks() computes a length of a hole, it doesn't count
with the fact that mapped offset may be somewhere in the middle of the
completely empty subtree. In such case it will return too large length
of the hole which then results in lseek(SEEK_DATA) to end up returning
an incorrect offset beyond the end of the hole.
Fix the problem by correctly taking offset within a subtree into account
when computing a length of a hole.
Fixes:
facab4d9711e7aa3532cb82643803e8f1b9518e8
CC: stable@vger.kernel.org
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trond Myklebust [Thu, 19 Oct 2017 19:46:45 +0000 (15:46 -0400)]
NFSv4.1: Fix up replays of interrupted requests
commit
3be0f80b5fe9c16eca2d538f799b94ca8aa59433 upstream.
If the previous request on a slot was interrupted before it was
processed by the server, then our slot sequence number may be out of whack,
and so we try the next operation using the old sequence number.
The problem with this, is that not all servers check to see that the
client is replaying the same operations as previously when they decide
to go to the replay cache, and so instead of the expected error of
NFS4ERR_SEQ_FALSE_RETRY, we get a replay of the old reply, which could
(if the operations match up) be mistaken by the client for a new reply.
To fix this, we attempt to send a COMPOUND containing only the SEQUENCE op
in order to resync our slot sequence number.
Cc: Olga Kornievskaia <olga.kornievskaia@gmail.com>
[olga.kornievskaia@gmail.com: fix an Oops]
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Borkmann [Fri, 15 Jun 2018 01:07:45 +0000 (03:07 +0200)]
tls: fix use-after-free in tls_push_record
[ Upstream commit
a447da7d00410278c90d3576782a43f8b675d7be ]
syzkaller managed to trigger a use-after-free in tls like the
following:
BUG: KASAN: use-after-free in tls_push_record.constprop.15+0x6a2/0x810 [tls]
Write of size 1 at addr
ffff88037aa08000 by task a.out/2317
CPU: 3 PID: 2317 Comm: a.out Not tainted 4.17.0+ #144
Hardware name: LENOVO 20FBCTO1WW/20FBCTO1WW, BIOS N1FET47W (1.21 ) 11/28/2016
Call Trace:
dump_stack+0x71/0xab
print_address_description+0x6a/0x280
kasan_report+0x258/0x380
? tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_push_record.constprop.15+0x6a2/0x810 [tls]
tls_sw_push_pending_record+0x2e/0x40 [tls]
tls_sk_proto_close+0x3fe/0x710 [tls]
? tcp_check_oom+0x4c0/0x4c0
? tls_write_space+0x260/0x260 [tls]
? kmem_cache_free+0x88/0x1f0
inet_release+0xd6/0x1b0
__sock_release+0xc0/0x240
sock_close+0x11/0x20
__fput+0x22d/0x660
task_work_run+0x114/0x1a0
do_exit+0x71a/0x2780
? mm_update_next_owner+0x650/0x650
? handle_mm_fault+0x2f5/0x5f0
? __do_page_fault+0x44f/0xa50
? mm_fault_error+0x2d0/0x2d0
do_group_exit+0xde/0x300
__x64_sys_exit_group+0x3a/0x50
do_syscall_64+0x9a/0x300
? page_fault+0x8/0x30
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This happened through fault injection where aead_req allocation in
tls_do_encryption() eventually failed and we returned -ENOMEM from
the function. Turns out that the use-after-free is triggered from
tls_sw_sendmsg() in the second tls_push_record(). The error then
triggers a jump to waiting for memory in sk_stream_wait_memory()
resp. returning immediately in case of MSG_DONTWAIT. What follows is
the trim_both_sgl(sk, orig_size), which drops elements from the sg
list added via tls_sw_sendmsg(). Now the use-after-free gets triggered
when the socket is being closed, where tls_sk_proto_close() callback
is invoked. The tls_complete_pending_work() will figure that there's
a pending closed tls record to be flushed and thus calls into the
tls_push_pending_closed_record() from there. ctx->push_pending_record()
is called from the latter, which is the tls_sw_push_pending_record()
from sw path. This again calls into tls_push_record(). And here the
tls_fill_prepend() will panic since the buffer address has been freed
earlier via trim_both_sgl(). One way to fix it is to move the aead
request allocation out of tls_do_encryption() early into tls_push_record().
This means we don't prep the tls header and advance state to the
TLS_PENDING_CLOSED_RECORD before allocation which could potentially
fail happened. That fixes the issue on my side.
Fixes:
3c4d7559159b ("tls: kernel TLS support")
Reported-by: syzbot+5c74af81c547738e1684@syzkaller.appspotmail.com
Reported-by: syzbot+709f2810a6a05f11d4d3@syzkaller.appspotmail.com
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dexuan Cui [Wed, 6 Jun 2018 21:32:51 +0000 (21:32 +0000)]
hv_netvsc: Fix a network regression after ifdown/ifup
[ Upstream commit
52acf73b6e9a6962045feb2ba5a8921da2201915 ]
Recently people reported the NIC stops working after
"ifdown eth0; ifup eth0". It turns out in this case the TX queues are not
enabled, after the refactoring of the common detach logic: when the NIC
has sub-channels, usually we enable all the TX queues after all
sub-channels are set up: see rndis_set_subchannel() ->
netif_device_attach(), but in the case of "ifdown eth0; ifup eth0" where
the number of channels doesn't change, we also must make sure the TX queues
are enabled. The patch fixes the regression.
Fixes:
7b2ee50c0cd5 ("hv_netvsc: common detach logic")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Willem de Bruijn [Wed, 6 Jun 2018 15:23:01 +0000 (11:23 -0400)]
net: in virtio_net_hdr only add VLAN_HLEN to csum_start if payload holds vlan
[ Upstream commit
fd3a88625844907151737fc3b4201676effa6d27 ]
Tun, tap, virtio, packet and uml vector all use struct virtio_net_hdr
to communicate packet metadata to userspace.
For skbuffs with vlan, the first two return the packet as it may have
existed on the wire, inserting the VLAN tag in the user buffer. Then
virtio_net_hdr.csum_start needs to be adjusted by VLAN_HLEN bytes.
Commit
f09e2249c4f5 ("macvtap: restore vlan header on user read")
added this feature to macvtap. Commit
3ce9b20f1971 ("macvtap: Fix
csum_start when VLAN tags are present") then fixed up csum_start.
Virtio, packet and uml do not insert the vlan header in the user
buffer.
When introducing virtio_net_hdr_from_skb to deduplicate filling in
the virtio_net_hdr, the variant from macvtap which adds VLAN_HLEN was
applied uniformly, breaking csum offset for packets with vlan on
virtio and packet.
Make insertion of VLAN_HLEN optional. Convert the callers to pass it
when needed.
Fixes:
e858fae2b0b8f4 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Fixes:
1276f24eeef2 ("packet: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paolo Abeni [Fri, 8 Jun 2018 09:35:40 +0000 (11:35 +0200)]
udp: fix rx queue len reported by diag and proc interface
[ Upstream commit
6c206b20092a3623184cff9470dba75d21507874 ]
After commit
6b229cf77d68 ("udp: add batching to udp_rmem_release()")
the sk_rmem_alloc field does not measure exactly anymore the
receive queue length, because we batch the rmem release. The issue
is really apparent only after commit
0d4a6608f68c ("udp: do rmem bulk
free even if the rx sk queue is empty"): the user space can easily
check for an empty socket with not-0 queue length reported by the 'ss'
tool or the procfs interface.
We need to use a custom UDP helper to report the correct queue length,
taking into account the forward allocation deficit.
Reported-by: trevor.francis@46labs.com
Fixes:
6b229cf77d68 ("UDP: add batching to udp_rmem_release()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cong Wang [Thu, 7 Jun 2018 20:39:49 +0000 (13:39 -0700)]
socket: close race condition between sock_close() and sockfs_setattr()
[ Upstream commit
6d8c50dcb029872b298eea68cc6209c866fd3e14 ]
fchownat() doesn't even hold refcnt of fd until it figures out
fd is really needed (otherwise is ignored) and releases it after
it resolves the path. This means sock_close() could race with
sockfs_setattr(), which leads to a NULL pointer dereference
since typically we set sock->sk to NULL in ->release().
As pointed out by Al, this is unique to sockfs. So we can fix this
in socket layer by acquiring inode_lock in sock_close() and
checking against NULL in sockfs_setattr().
sock_release() is called in many places, only the sock_close()
path matters here. And fortunately, this should not affect normal
sock_close() as it is only called when the last fd refcnt is gone.
It only affects sock_close() with a parallel sockfs_setattr() in
progress, which is not common.
Fixes:
86741ec25462 ("net: core: Add a UID field to struct sock.")
Reported-by: shankarapailoor <shankarapailoor@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frank van der Linden [Tue, 12 Jun 2018 23:09:37 +0000 (23:09 +0000)]
tcp: verify the checksum of the first data segment in a new connection
[ Upstream commit
4fd44a98ffe0d048246efef67ed640fdf2098a62 ]
commit
079096f103fa ("tcp/dccp: install syn_recv requests into ehash
table") introduced an optimization for the handling of child sockets
created for a new TCP connection.
But this optimization passes any data associated with the last ACK of the
connection handshake up the stack without verifying its checksum, because it
calls tcp_child_process(), which in turn calls tcp_rcv_state_process()
directly. These lower-level processing functions do not do any checksum
verification.
Insert a tcp_checksum_complete call in the TCP_NEW_SYN_RECEIVE path to
fix this.
Fixes:
079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Davide Caratti [Fri, 8 Jun 2018 03:02:31 +0000 (05:02 +0200)]
net/sched: act_simple: fix parsing of TCA_DEF_DATA
[ Upstream commit
8d499533e0bc02d44283dbdab03142b599b8ba16 ]
use nla_strlcpy() to avoid copying data beyond the length of TCA_DEF_DATA
netlink attribute, in case it is less than SIMP_MAX_DATA and it does not
end with '\0' character.
v2: fix errors in the commit message, thanks Hangbin Liu
Fixes:
fa1b1cff3d06 ("net_cls_act: Make act_simple use of netlink policy.")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Zhouyang Jia [Mon, 11 Jun 2018 05:26:35 +0000 (13:26 +0800)]
net: dsa: add error handling for pskb_trim_rcsum
[ Upstream commit
349b71d6f427ff8211adf50839dbbff3f27c1805 ]
When pskb_trim_rcsum fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pskb_trim_rcsum.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julian Anastasov [Sun, 10 Jun 2018 23:02:54 +0000 (02:02 +0300)]
ipv6: allow PMTU exceptions to local routes
[ Upstream commit
0975764684487bf3f7a47eef009e750ea41bd514 ]
IPVS setups with local client and remote tunnel server need
to create exception for the local virtual IP. What we do is to
change PMTU from 64KB (on "lo") to 1460 in the common case.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Fixes:
45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception")
Fixes:
7343ff31ebf0 ("ipv6: Don't create clones of host routes.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Fri, 8 Jun 2018 07:15:24 +0000 (09:15 +0200)]
cdc_ncm: avoid padding beyond end of skb
[ Upstream commit
49c2c3f246e2fc3009039e31a826333dcd0283cd ]
Commit
4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end
of NCM frame") added logic to reserve space for the NDP at the
end of the NTB/skb. This reservation did not take the final
alignment of the NDP into account, causing us to reserve too
little space. Additionally the padding prior to NDP addition did
not ensure there was enough space for the NDP.
The NTB/skb with the NDP appended would then exceed the configured
max size. This caused the final padding of the NTB to use a
negative count, padding to almost INT_MAX, and resulting in:
[60103.825970] BUG: unable to handle kernel paging request at
ffff9641f2004000
[60103.825998] IP: __memset+0x24/0x30
[60103.826001] PGD
a6a06067 P4D
a6a06067 PUD
4f65a063 PMD
72003063 PTE 0
[60103.826013] Oops: 0002 [#1] SMP NOPTI
[60103.826018] Modules linked in: (removed(
[60103.826158] CPU: 0 PID: 5990 Comm: Chrome_DevTools Tainted: G O 4.14.0-3-amd64 #1 Debian 4.14.17-1
[60103.826162] Hardware name: LENOVO 20081 BIOS 41CN28WW(V2.04) 05/03/2012
[60103.826166] task:
ffff964193484fc0 task.stack:
ffffb2890137c000
[60103.826171] RIP: 0010:__memset+0x24/0x30
[60103.826174] RSP: 0000:
ffff964316c03b68 EFLAGS:
00010216
[60103.826178] RAX:
0000000000000000 RBX:
00000000fffffffd RCX:
000000001ffa5000
[60103.826181] RDX:
0000000000000005 RSI:
0000000000000000 RDI:
ffff9641f2003ffc
[60103.826184] RBP:
ffff964192f6c800 R08:
00000000304d434e R09:
ffff9641f1d2c004
[60103.826187] R10:
0000000000000002 R11:
00000000000005ae R12:
ffff9642e6957a80
[60103.826190] R13:
ffff964282ff2ee8 R14:
000000000000000d R15:
ffff9642e4843900
[60103.826194] FS:
00007f395aaf6700(0000) GS:
ffff964316c00000(0000) knlGS:
0000000000000000
[60103.826197] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[60103.826200] CR2:
ffff9641f2004000 CR3:
0000000013b0c000 CR4:
00000000000006f0
[60103.826204] Call Trace:
[60103.826212] <IRQ>
[60103.826225] cdc_ncm_fill_tx_frame+0x5e3/0x740 [cdc_ncm]
[60103.826236] cdc_ncm_tx_fixup+0x57/0x70 [cdc_ncm]
[60103.826246] usbnet_start_xmit+0x5d/0x710 [usbnet]
[60103.826254] ? netif_skb_features+0x119/0x250
[60103.826259] dev_hard_start_xmit+0xa1/0x200
[60103.826267] sch_direct_xmit+0xf2/0x1b0
[60103.826273] __dev_queue_xmit+0x5e3/0x7c0
[60103.826280] ? ip_finish_output2+0x263/0x3c0
[60103.826284] ip_finish_output2+0x263/0x3c0
[60103.826289] ? ip_output+0x6c/0xe0
[60103.826293] ip_output+0x6c/0xe0
[60103.826298] ? ip_forward_options+0x1a0/0x1a0
[60103.826303] tcp_transmit_skb+0x516/0x9b0
[60103.826309] tcp_write_xmit+0x1aa/0xee0
[60103.826313] ? sch_direct_xmit+0x71/0x1b0
[60103.826318] tcp_tasklet_func+0x177/0x180
[60103.826325] tasklet_action+0x5f/0x110
[60103.826332] __do_softirq+0xde/0x2b3
[60103.826337] irq_exit+0xae/0xb0
[60103.826342] do_IRQ+0x81/0xd0
[60103.826347] common_interrupt+0x98/0x98
[60103.826351] </IRQ>
[60103.826355] RIP: 0033:0x7f397bdf2282
[60103.826358] RSP: 002b:
00007f395aaf57d8 EFLAGS:
00000206 ORIG_RAX:
ffffffffffffff6e
[60103.826362] RAX:
0000000000000000 RBX:
00002f07bc6d0900 RCX:
00007f39752d7fe7
[60103.826365] RDX:
0000000000000022 RSI:
0000000000000147 RDI:
00002f07baea02c0
[60103.826368] RBP:
0000000000000001 R08:
0000000000000000 R09:
0000000000000000
[60103.826371] R10:
00000000ffffffff R11:
0000000000000000 R12:
00002f07baea02c0
[60103.826373] R13:
00002f07bba227a0 R14:
00002f07bc6d090c R15:
0000000000000000
[60103.826377] Code: 90 90 90 90 90 90 90 0f 1f 44 00 00 49 89 f9 48 89 d1 83
e2 07 48 c1 e9 03 40 0f b6 f6 48 b8 01 01 01 01 01 01 01 01 48 0f af c6 <f3> 48
ab 89 d1 f3 aa 4c 89 c8 c3 90 49 89 f9 40 88 f0 48 89 d1
[60103.826442] RIP: __memset+0x24/0x30 RSP:
ffff964316c03b68
[60103.826444] CR2:
ffff9641f2004000
Commit
e1069bbfcf3b ("net: cdc_ncm: Reduce memory use when kernel
memory low") made this bug much more likely to trigger by reducing
the NTB size under memory pressure.
Link: https://bugs.debian.org/893393
Reported-by: Горбешко Богдан <bodqhrohro@gmail.com>
Reported-and-tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Fixes:
4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xiangning Yu [Thu, 7 Jun 2018 05:39:59 +0000 (13:39 +0800)]
bonding: re-evaluate force_primary when the primary slave name changes
[ Upstream commit
eb55bbf865d9979098c6a7a17cbdb41237ece951 ]
There is a timing issue under active-standy mode, when bond_enslave() is
called, bond->params.primary might not be initialized yet.
Any time the primary slave string changes, bond->force_primary should be
set to true to make sure the primary becomes the active slave.
Signed-off-by: Xiangning Yu <yuxiangning@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Wed, 20 Jun 2018 19:03:02 +0000 (04:03 +0900)]
Linux 4.14.51
Eric Dumazet [Mon, 11 Dec 2017 01:55:02 +0000 (17:55 -0800)]
tcp: do not overshoot window_clamp in tcp_rcv_space_adjust()
commit
02db55718d53f9d426cee504c27fb768e9ed4ffe upstream.
While rcvbuf is properly clamped by tcp_rmem[2], rcvwin
is left to a potentially too big value.
It has no serious effect, since :
1) tcp_grow_window() has very strict checks.
2) window_clamp can be mangled by user space to any value anyway.
tcp_init_buffer_space() and companions use tcp_full_space(),
we use tcp_win_from_space() to avoid reloading sk->sk_rcvbuf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Benjamin Gilbert <benjamin.gilbert@coreos.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Bo [Fri, 15 Jun 2018 02:39:04 +0000 (02:39 +0000)]
Btrfs: make raid6 rebuild retry more
[ Upstream commit
8810f7517a3bc4ca2d41d022446d3f5fd6b77c09 ]
There is a scenario that can end up with rebuild process failing to
return good content, i.e.
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content, and users will think of this as data loss.
More seriouly, if the loss happens on some important internal btree
roots, it could refuse to mount.
This extends btrfs to do more retries and each retry fails only one
stripe. Since raid6 can tolerate 2 disk failures, if there is one
more failure besides the failure on which we're recovering, this can
always work.
The worst case is to retry as many times as the number of raid6 disks,
but given the fact that such a scenario is really rare in practice,
it's still acceptable.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Liu Bo [Fri, 15 Jun 2018 02:39:02 +0000 (02:39 +0000)]
Btrfs: fix scrub to repair raid6 corruption
[ Upstream commit
762221f095e3932669093466aaf4b85ed9ad2ac1 ]
The raid6 corruption is that,
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content.
We've fixed normal reads to rebuild raid6 correctly with more retries
in Patch "Btrfs: make raid6 rebuild retry more"[1], this is to fix
scrub to do the exactly same rebuild process.
[1]: https://patchwork.kernel.org/patch/
10091755/
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sasha Levin [Fri, 15 Jun 2018 02:39:01 +0000 (02:39 +0000)]
Revert "Btrfs: fix scrub to repair raid6 corruption"
This reverts commit
d91bb7c6988bd6450284c762b33f2e1ea3fe7c97.
This commit used an incorrect log message.
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Wed, 11 Apr 2018 17:24:01 +0000 (18:24 +0100)]
ARM: kexec: fix kdump register saving on panic()
[ Upstream commit
2d7b3c64431245c95b05a441669c074da10db943 ]
When a panic() occurs, the kexec code uses smp_send_stop() to stop
the other CPUs, but this results in the CPU register state not being
saved, and gdb is unable to inspect the state of other CPUs.
Commit
0ee59413c967 ("x86/panic: replace smp_send_stop() with kdump
friendly version in panic path") addressed the issue on x86, but
ignored other architectures. Address the issue on ARM by splitting
out the crash stop implementation to crash_smp_send_stop() and
adding the necessary protection.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Łukasz Stelmach [Wed, 4 Apr 2018 07:46:58 +0000 (08:46 +0100)]
ARM: 8758/1: decompressor: restore r1 and r2 just before jumping to the kernel
[ Upstream commit
f2ae9de019e4e2807d812ec4fe1df7c34788a0a0 ]
The hypervisor setup before __enter_kernel destroys the value
sotred in r1. The value needs to be restored just before the jump.
Fixes:
6b52f7bdb888 ("ARM: hyp-stub: Use r1 for the soft-restart address")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Łukasz Stelmach [Tue, 3 Apr 2018 08:04:57 +0000 (09:04 +0100)]
ARM: 8753/1: decompressor: add a missing parameter to the addruart macro
[ Upstream commit
e07e3c33b9c0b5751ade624f44325c9bf2487ea6 ]
In commit
639da5ee374b ("ARM: add an extra temp register to the low
level debugging addruart macro") an additional temporary register was
added to the addruart macro, but the decompressor code wasn't updated.
Fixes:
639da5ee374b ("ARM: add an extra temp register to the low level debugging addruart macro")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Rutland [Fri, 18 May 2018 14:08:41 +0000 (16:08 +0200)]
efi/libstub/arm64: Handle randomized TEXT_OFFSET
[ Upstream commit
4f74d72aa7067e75af92fbab077e6d7d0210be66 ]
When CONFIG_RANDOMIZE_TEXT_OFFSET=y, TEXT_OFFSET is an arbitrary
multiple of PAGE_SIZE in the interval [0, 2MB).
The EFI stub does not account for the potential misalignment of
TEXT_OFFSET relative to EFI_KIMG_ALIGN, and produces a randomized
physical offset which is always a round multiple of EFI_KIMG_ALIGN.
This may result in statically allocated objects whose alignment exceeds
PAGE_SIZE to appear misaligned in memory. This has been observed to
result in spurious stack overflow reports and failure to make use of
the IRQ stacks, and theoretically could result in a number of other
issues.
We can OR in the low bits of TEXT_OFFSET to ensure that we have the
necessary offset (and hence preserve the misalignment of TEXT_OFFSET
relative to EFI_KIMG_ALIGN), so let's do that.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
[ardb: clarify comment and commit log, drop unneeded parens]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes:
6f26b3671184c36d ("arm64: kaslr: increase randomization granularity")
Link: http://lkml.kernel.org/r/20180518140841.9731-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Helge Deller [Fri, 18 May 2018 14:12:12 +0000 (16:12 +0200)]
parisc: Move setup_profiling_timer() out of init section
[ Upstream commit
01f56832cfb6fcc204e7203f46841b6185ebd574 ]
No other architecture has setup_profiling_timer() in the init section,
thus on parisc we face this section mismatch warning:
Reference from the function devm_device_add_group() to the function .init.text:setup_profiling_timer()
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Malaterre [Wed, 16 May 2018 20:09:02 +0000 (22:09 +0200)]
sched/deadline: Make the grub_reclaim() function static
[ Upstream commit
3febfc8a219a036633b57a34c6678e21b6a0580d ]
Since the grub_reclaim() function can be made static, make it so.
Silences the following GCC warning (W=1):
kernel/sched/deadline.c:1120:5: warning: no previous prototype for ‘grub_reclaim’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180516200902.959-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Malaterre [Wed, 16 May 2018 19:53:47 +0000 (21:53 +0200)]
sched/debug: Move the print_rt_rq() and print_dl_rq() declarations to kernel/sched/sched.h
[ Upstream commit
f6a3463063f42d9fb2c78f386437a822e0ad1792 ]
In the following commit:
6b55c9654fcc ("sched/debug: Move print_cfs_rq() declaration to kernel/sched/sched.h")
the print_cfs_rq() prototype was added to <kernel/sched/sched.h>,
right next to the prototypes for print_cfs_stats(), print_rt_stats()
and print_dl_stats().
Finish this previous commit and also move related prototypes for
print_rt_rq() and print_dl_rq().
Remove existing extern declarations now that they not needed anymore.
Silences the following GCC warning, triggered by W=1:
kernel/sched/debug.c:573:6: warning: no previous prototype for ‘print_rt_rq’ [-Wmissing-prototypes]
kernel/sched/debug.c:603:6: warning: no previous prototype for ‘print_dl_rq’ [-Wmissing-prototypes]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20180516195348.30426-1-malat@debian.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Wed, 16 May 2018 14:00:26 +0000 (17:00 +0300)]
drm/dumb-buffers: Integer overflow in drm_mode_create_ioctl()
[ Upstream commit
2b6207291b7b277a5df9d1aab44b56815a292dba ]
There is a comment here which says that DIV_ROUND_UP() and that's where
the problem comes from. Say you pick:
args->bpp = UINT_MAX - 7;
args->width = 4;
args->height = 1;
The integer overflow in DIV_ROUND_UP() means "cpp" is UINT_MAX / 8 and
because of how we picked args->width that means cpp < UINT_MAX / 4.
I've fixed it by preventing the integer overflow in DIV_ROUND_UP(). I
removed the check for !cpp because it's not possible after this change.
I also changed all the 0xffffffffU references to U32_MAX.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180516140026.GA19340@mwanda
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiman Long [Tue, 15 May 2018 21:49:51 +0000 (17:49 -0400)]
locking/percpu-rwsem: Annotate rwsem ownership transfer by setting RWSEM_OWNER_UNKNOWN
[ Upstream commit
5a817641f68a6399a5fac8b7d2da67a73698ffed ]
The filesystem freezing code needs to transfer ownership of a rwsem
embedded in a percpu-rwsem from the task that does the freezing to
another one that does the thawing by calling percpu_rwsem_release()
after freezing and percpu_rwsem_acquire() before thawing.
However, the new rwsem debug code runs afoul with this scheme by warning
that the task that releases the rwsem isn't the one that acquires it,
as reported by Amir Goldstein:
DEBUG_LOCKS_WARN_ON(sem->owner != get_current())
WARNING: CPU: 1 PID: 1401 at /home/amir/build/src/linux/kernel/locking/rwsem.c:133 up_write+0x59/0x79
Call Trace:
percpu_up_write+0x1f/0x28
thaw_super_locked+0xdf/0x120
do_vfs_ioctl+0x270/0x5f1
ksys_ioctl+0x52/0x71
__x64_sys_ioctl+0x16/0x19
do_syscall_64+0x5d/0x167
entry_SYSCALL_64_after_hwframe+0x49/0xbe
To work properly with the rwsem debug code, we need to annotate that the
rwsem ownership is unknown during the tranfer period until a brave soul
comes forward to acquire the ownership. During that period, optimistic
spinning will be disabled.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Tested-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jan Kara <jack@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Theodore Y. Ts'o <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-fsdevel@vger.kernel.org
Link: http://lkml.kernel.org/r/1526420991-21213-3-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiman Long [Tue, 15 May 2018 21:49:50 +0000 (17:49 -0400)]
locking/rwsem: Add a new RWSEM_ANONYMOUSLY_OWNED flag
[ Upstream commit
d7d760efad70c7a030725499bf9f342f04af24dd ]
There are use cases where a rwsem can be acquired by one task, but
released by another task. In thess cases, optimistic spinning may need
to be disabled. One example will be the filesystem freeze/thaw code
where the task that freezes the filesystem will acquire a write lock
on a rwsem and then un-owns it before returning to userspace. Later on,
another task will come along, acquire the ownership, thaw the filesystem
and release the rwsem.
Bit 0 of the owner field was used to designate that it is a reader
owned rwsem. It is now repurposed to mean that the owner of the rwsem
is not known. If only bit 0 is set, the rwsem is reader owned. If bit
0 and other bits are set, it is writer owned with an unknown owner.
One such value for the latter case is (-1L). So we can set owner to 1 for
reader-owned, -1 for writer-owned. The owner is unknown in both cases.
To handle transfer of rwsem ownership, the higher level code should
set the owner field to -1 to indicate a write-locked rwsem with unknown
owner. Optimistic spinning will be disabled in this case.
Once the higher level code figures who the new owner is, it can then
set the owner field accordingly.
Tested-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Jan Kara <jack@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Theodore Y. Ts'o <tytso@mit.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-fsdevel@vger.kernel.org
Link: http://lkml.kernel.org/r/1526420991-21213-2-git-send-email-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefan Agner [Wed, 18 Apr 2018 12:49:08 +0000 (14:49 +0200)]
clk: imx6ull: use OSC clock during AXI rate change
[ Upstream commit
2e5be528ab0182ad4b42b9feea3b80f85f37179b ]
On i.MX6 ULL using PLL3 seems to cause a freeze when setting
the parent to IMX6UL_CLK_PLL3_USB_OTG. This only seems to appear
since commit
6f9575e55632 ("clk: imx: Add CLK_IS_CRITICAL flag
for busy divider and busy mux"), probably because the clock is
now forced to be on.
Fixes:
6f9575e55632("clk: imx: Add CLK_IS_CRITICAL flag for busy divider and busy mux")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sekhar Nori [Fri, 11 May 2018 15:21:36 +0000 (20:51 +0530)]
ARM: davinci: board-dm646x-evm: set VPIF capture card name
[ Upstream commit
bb7298a7e87cf3430eb62be8746e5d7a07ca9d7c ]
VPIF capture driver expects card name to be set since it
uses it without checking for NULL. The commit which
introduced VPIF display and capture support added card
name only for display, not for capture.
Set it in platform data to probe driver successfully.
While at it, also fix the display card name to something more
appropriate.
Fixes:
85609c1ccda6 ("DaVinci: DM646x - platform changes for vpif capture and display drivers")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sekhar Nori [Fri, 11 May 2018 15:21:35 +0000 (20:51 +0530)]
ARM: davinci: board-dm646x-evm: pass correct I2C adapter id for VPIF
[ Upstream commit
7d46899d57f8b61eb28701d9a4043b71e3392c26 ]
commit
a16cb91ad9c4 ("[media] media: vpif: use a configurable
i2c_adapter_id for vpif display") removed hardcoded I2C adaptor
setting in VPIF driver, but missed updating platform data passed
from DM646x board.
Fix it.
Fixes:
a16cb91ad9c4 ("[media] media: vpif: use a configurable i2c_adapter_id for vpif display")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sekhar Nori [Fri, 11 May 2018 15:21:34 +0000 (20:51 +0530)]
ARM: davinci: dm646x: fix timer interrupt generation
[ Upstream commit
73d4337ed9ceddef4b2f0e226634d5f985aa2d1c ]
commit
b38434145b34 ("ARM: davinci: irqs: Correct McASP1 TX interrupt
definition for DM646x") inadvertently removed priority setting for
timer0_12 (bottom half of timer0). This timer is used as clockevent.
When INTPRIn register setting for an interrupt is left at 0, it is
mapped to FIQ by the AINTC causing the timer interrupt to not get
generated.
Fix it by including an entry for timer0_12 in interrupt priority map
array. While at it, move the clockevent comment to the right place.
Fixes:
b38434145b34 ("ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Rosin [Wed, 9 May 2018 19:47:48 +0000 (21:47 +0200)]
i2c: viperboard: return message count on master_xfer success
[ Upstream commit
35cd67a0caf767aba472452865dcb4471fcce2b1 ]
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes:
174a13aa8669 ("i2c: Add viperboard i2c master driver")
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Rosin [Wed, 9 May 2018 19:46:30 +0000 (21:46 +0200)]
i2c: pmcmsp: fix error return from master_xfer
[ Upstream commit
12d9bbc5a7f347eaa65ff2a9d34995cadc05eb1b ]
Returning -1 (-EPERM) is not appropriate here, go with -EIO.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes:
1b144df1d7d6 ("i2c: New PMC MSP71xx TWI bus driver")
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Rosin [Wed, 9 May 2018 19:46:29 +0000 (21:46 +0200)]
i2c: pmcmsp: return message count on master_xfer success
[ Upstream commit
de9a8634f1cb4560a35696d472cc7f1383d9b866 ]
Returning zero is wrong in this case.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes:
1b144df1d7d6 ("i2c: New PMC MSP71xx TWI bus driver")
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russell King [Thu, 10 May 2018 13:24:20 +0000 (14:24 +0100)]
ARM: keystone: fix platform_domain_notifier array overrun
[ Upstream commit
9954b80b8c0e8abc98e17bba0fccd9876211ceaa ]
platform_domain_notifier contains a variable sized array, which the
pm_clk_notify() notifier treats as a NULL terminated array:
for (con_id = clknb->con_ids; *con_id; con_id++)
pm_clk_add(dev, *con_id);
Omitting the initialiser for con_ids means that the array is zero
sized, and there is no NULL terminator. This leads to pm_clk_notify()
overrunning into what ever structure follows, which may not be NULL.
This leads to an oops:
Unable to handle kernel NULL pointer dereference at virtual address
0000008c
pgd =
c0003000
[
0000008c] *pgd=
80000800004003c, *pmd=
00000000c
Internal error: Oops: 206 [#1] PREEMPT SMP ARM
Modules linked in:c
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.16.0+ #9
Hardware name: Keystone
PC is at strlen+0x0/0x34
LR is at kstrdup+0x18/0x54
pc : [<
c0623340>] lr : [<
c0111d6c>] psr:
20000013
sp :
eec73dc0 ip :
eed780c0 fp :
00000001
r10:
00000000 r9 :
00000000 r8 :
eed71e10
r7 :
0000008c r6 :
0000008c r5 :
014000c0 r4 :
c03a6ff4
r3 :
c09445d0 r2 :
00000000 r1 :
014000c0 r0 :
0000008c
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control:
30c5387d Table:
00003000 DAC:
fffffffd
Process swapper/0 (pid: 1, stack limit = 0xeec72210)
Stack: (0xeec73dc0 to 0xeec74000)
...
[<
c0623340>] (strlen) from [<
c0111d6c>] (kstrdup+0x18/0x54)
[<
c0111d6c>] (kstrdup) from [<
c03a6ff4>] (__pm_clk_add+0x58/0x120)
[<
c03a6ff4>] (__pm_clk_add) from [<
c03a731c>] (pm_clk_notify+0x64/0xa8)
[<
c03a731c>] (pm_clk_notify) from [<
c004614c>] (notifier_call_chain+0x44/0x84)
[<
c004614c>] (notifier_call_chain) from [<
c0046320>] (__blocking_notifier_call_chain+0x48/0x60)
[<
c0046320>] (__blocking_notifier_call_chain) from [<
c0046350>] (blocking_notifier_call_chain+0x18/0x20)
[<
c0046350>] (blocking_notifier_call_chain) from [<
c0390234>] (device_add+0x36c/0x534)
[<
c0390234>] (device_add) from [<
c047fc00>] (of_platform_device_create_pdata+0x70/0xa4)
[<
c047fc00>] (of_platform_device_create_pdata) from [<
c047fea0>] (of_platform_bus_create+0xf0/0x1ec)
[<
c047fea0>] (of_platform_bus_create) from [<
c047fff8>] (of_platform_populate+0x5c/0xac)
[<
c047fff8>] (of_platform_populate) from [<
c08b1f04>] (of_platform_default_populate_init+0x8c/0xa8)
[<
c08b1f04>] (of_platform_default_populate_init) from [<
c000a78c>] (do_one_initcall+0x3c/0x164)
[<
c000a78c>] (do_one_initcall) from [<
c087bd9c>] (kernel_init_freeable+0x10c/0x1d0)
[<
c087bd9c>] (kernel_init_freeable) from [<
c0628db0>] (kernel_init+0x8/0xf0)
[<
c0628db0>] (kernel_init) from [<
c00090d8>] (ret_from_fork+0x14/0x3c)
Exception stack(0xeec73fb0 to 0xeec73ff8)
3fa0:
00000000 00000000 00000000 00000000
3fc0:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0:
00000000 00000000 00000000 00000000 00000013 00000000
Code:
e3520000 1afffff7 e12fff1e c0801730 (
e5d02000)
---[ end trace
cafa8f148e262e80 ]---
Fix this by adding the necessary initialiser.
Fixes:
fc20ffe1213b ("ARM: keystone: add PM domain support for clock management")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Glöckner [Mon, 14 May 2018 14:40:05 +0000 (09:40 -0500)]
usb: musb: fix remote wakeup racing with suspend
[ Upstream commit
ebc3dd688cd988754a304147753b13e58de1b5a1 ]
It has been observed that writing 0xF2 to the power register while it
reads as 0xF4 results in the register having the value 0xF0, i.e. clearing
RESUME and setting SUSPENDM in one go does not work. It might also violate
the USB spec to transition directly from resume to suspend, especially
when not taking T_DRSMDN into account. But this is what happens when a
remote wakeup occurs between SetPortFeature USB_PORT_FEAT_SUSPEND on the
root hub and musb_bus_suspend being called.
This commit returns -EBUSY when musb_bus_suspend is called while remote
wakeup is signalled and thus avoids to reset the RESUME bit. Ignoring
this error when musb_port_suspend is called from musb_hub_control is ok.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Thu, 10 May 2018 22:10:40 +0000 (23:10 +0100)]
afs: Fix the non-encryption of calls
[ Upstream commit
4776cab43fd3111618112737a257dc3ef368eddd ]
Some AFS servers refuse to accept unencrypted traffic, so can't be accessed
with kAFS. Set the AF_RXRPC security level to encrypt client calls to deal
with this.
Note that incoming service calls are set by the remote client and so aren't
affected by this.
This requires an AF_RXRPC patch to pass the value set by setsockopt to calls
begun by the kernel.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Thu, 10 May 2018 18:20:54 +0000 (19:20 +0100)]
mtd: Fix comparison in map_word_andequal()
[ Upstream commit
ea739a287f4f16d6250bea779a1026ead79695f2 ]
Commit
9e343e87d2c4 ("mtd: cfi: convert inline functions to macros")
changed map_word_andequal() into a macro, but also changed the right
hand side of the comparison from val3 to val2. Change it back to use
val3 on the right hand side.
Thankfully this did not cause a regression because all callers
currently pass the same argument for val2 and val3.
Fixes:
9e343e87d2c4 ("mtd: cfi: convert inline functions to macros")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:56 +0000 (10:13 -0700)]
x86/pkeys/selftests: Add a test for pkey 0
[ Upstream commit
3488a600d90bcaf061b104dbcfbdc8d99b398312 ]
Protection key 0 is the default key for all memory and will
not normally come back from pkey_alloc(). But, you might
still want pass it to mprotect_pkey().
This check ensures that you can use pkey 0.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171356.9E40B254@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:54 +0000 (10:13 -0700)]
x86/pkeys/selftests: Save off 'prot' for allocations
[ Upstream commit
acb25d761d6f2f64e785ccefc71e54f244f1eda4 ]
This makes it possible to to tell what 'prot' a given allocation
is supposed to have. That way, if we want to change just the
pkey, we know what 'prot' to pass to mprotect_pkey().
Also, keep a record of the most recent allocation so the tests
can easily find it.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171354.AA23E228@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:52 +0000 (10:13 -0700)]
x86/pkeys/selftests: Fix pointer math
[ Upstream commit
3d64f4ed15c3c53dba4c514bf59c334464dee373 ]
We dump out the entire area of the siginfo where the si_pkey_ptr is
supposed to be. But, we do some math on the poitner, which is a u32.
We intended to do byte math, not u32 math on the pointer.
Cast it over to a u8* so it works.
Also, move this block of code to below th si_code check. It doesn't
hurt anything, but the si_pkey field is gibberish for other signal
types.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171352.9BE09819@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:50 +0000 (10:13 -0700)]
x86/pkeys/selftests: Fix pkey exhaustion test off-by-one
[ Upstream commit
f50b4878329ab61d8e05796f655adeb6f5fb57c6 ]
In our "exhaust all pkeys" test, we make sure that there
is the expected number available. Turns out that the
test did not cover the execute-only key, but discussed
it anyway. It did *not* discuss the test-allocated
key.
Now that we have a test for the mprotect(PROT_EXEC) case,
this off-by-one issue showed itself. Correct the off-by-
one and add the explanation for the case we missed.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171350.E1656B95@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:48 +0000 (10:13 -0700)]
x86/pkeys/selftests: Add PROT_EXEC test
[ Upstream commit
6af17cf89e99b64cf1f660bf848755442ab2f047 ]
Under the covers, implement executable-only memory with
protection keys when userspace calls mprotect(PROT_EXEC).
But, we did not have a selftest for that. Now we do.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171348.9EEE4BEF@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:47 +0000 (10:13 -0700)]
x86/pkeys/selftests: Factor out "instruction page"
[ Upstream commit
3fcd2b2d928904cbf30b01e2c5e4f1dd2f9ab262 ]
We currently have an execute-only test, but it is for
the explicit mprotect_pkey() interface. We will soon
add a test for the implicit mprotect(PROT_EXEC)
enterface. We need this code in both tests.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171347.C64AB733@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:46 +0000 (10:13 -0700)]
x86/pkeys/selftests: Allow faults on unknown keys
[ Upstream commit
7e7fd67ca39335a49619729821efb7cbdd674eb0 ]
The exec-only pkey is allocated inside the kernel and userspace
is not told what it is. So, allow PK faults to occur that have
an unknown key.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171345.7FC7DA00@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:42 +0000 (10:13 -0700)]
x86/pkeys/selftests: Remove dead debugging code, fix dprint_in_signal
[ Upstream commit
a50093d60464dd51d1ae0c2267b0abe9e1de77f3 ]
There is some noisy debug code at the end of the signal handler. It was
disabled by an early, unconditional "return". However, that return also
hid a dprint_in_signal=0, which kept dprint_in_signal=1 and effectively
locked us into permanent dprint_in_signal=1 behavior.
Remove the return and the dead code, fixing dprint_in_signal.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171342.846B9B2E@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:40 +0000 (10:13 -0700)]
x86/pkeys/selftests: Stop using assert()
[ Upstream commit
86b9eea230edf4c67d4d4a70fba9b74505867a25 ]
If we use assert(), the program "crashes". That can be scary to users,
so stop doing it. Just exit with a >0 exit code instead.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171340.E63EF7DA@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Hansen [Wed, 9 May 2018 17:13:38 +0000 (10:13 -0700)]
x86/pkeys/selftests: Give better unexpected fault error messages
[ Upstream commit
55556b0b2016806b2e16a20b62d143383983a34a ]
do_not_expect_pk_fault() is a helper that we call when we do not expect
a PK fault to have occurred. But, it is a function, which means that
it obscures the line numbers from pkey_assert(). It also gives no
details.
Replace it with an implementation that gives nice line numbers and
also lets callers pass in a more descriptive message about what
happened that caused the unexpected fault.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Ellermen <mpe@ellerman.id.au>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ram Pai <linuxram@us.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20180509171338.55D13B64@viggo.jf.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andy Lutomirski [Tue, 8 May 2018 17:28:35 +0000 (10:28 -0700)]
x86/selftests: Add mov_to_ss test
[ Upstream commit
59c2a7226fc5130032021c99f05ad5c0a56551cd ]
This exercises a nasty corner case of the x86 ISA.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/67e08b69817171da8026e0eb3af0214b06b4d74f.1525800455.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingo Molnar [Mon, 14 May 2018 08:59:08 +0000 (10:59 +0200)]
x86/mpx/selftests: Adjust the self-test to fresh distros that export the MPX ABI
[ Upstream commit
73bb4d6cd192b8629c5125aaada9892d9fc986b6 ]
Fix this warning:
mpx-mini-test.c:422:0: warning: "SEGV_BNDERR" redefined
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: dave.hansen@intel.com
Cc: linux-mm@kvack.org
Cc: linuxram@us.ibm.com
Cc: mpe@ellerman.id.au
Cc: shakeelb@google.com
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180514085908.GA12798@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingo Molnar [Mon, 14 May 2018 08:56:23 +0000 (10:56 +0200)]
x86/pkeys/selftests: Adjust the self-test to fresh distros that export the pkeys ABI
[ Upstream commit
0fb96620dce351608aa82eed5942e2f58b07beda ]
Ubuntu 18.04 started exporting pkeys details in header files, resulting
in build failures and warnings in the pkeys self-tests:
protection_keys.c:232:0: warning: "SEGV_BNDERR" redefined
protection_keys.c:387:5: error: conflicting types for ‘pkey_get’
protection_keys.c:409:5: error: conflicting types for ‘pkey_set’
...
Fix these namespace conflicts and double definitions, plus also
clean up the ABI definitions to make it all a bit more readable ...
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: dave.hansen@intel.com
Cc: linux-mm@kvack.org
Cc: linuxram@us.ibm.com
Cc: mpe@ellerman.id.au
Cc: shakeelb@google.com
Cc: shuah@kernel.org
Link: http://lkml.kernel.org/r/20180514085623.GB7094@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingo Molnar [Mon, 14 May 2018 08:15:54 +0000 (10:15 +0200)]
objtool, kprobes/x86: Sync the latest <asm/insn.h> header with tools/objtool/arch/x86/include/asm/insn.h
[ Upstream commit
4fe875e4bd3cae85ae6f6eaf77f63fabe613b66e ]
The following commit:
ee6a7354a362: kprobes/x86: Prohibit probing on exception masking instructions
Modified <asm/insn.h>, adding the insn_masking_exception() function.
Sync the tooling version of the header to it, to fix this warning:
Warning: synced file at 'tools/objtool/arch/x86/include/asm/insn.h' differs from latest kernel version at 'arch/x86/include/asm/insn.h'
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Francis Deslauriers <francis.deslauriers@efficios.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "David S . Miller" <davem@davemloft.net>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Wed, 9 May 2018 12:58:45 +0000 (21:58 +0900)]
uprobes/x86: Prohibit probing on MOV SS instruction
[ Upstream commit
13ebe18c94f5b0665c01ae7fad2717ae959f4212 ]
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by uprobes must be
prohibited.
uprobe already rejects probing on POP SS (0x1f), but allows probing on MOV
SS (0x8e and reg == 2). This checks the target instruction and if it is
MOV SS or POP SS, returns -ENOTSUPP to reject probing.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Francis Deslauriers <francis.deslauriers@efficios.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "David S . Miller" <davem@davemloft.net>
Link: https://lkml.kernel.org/r/152587072544.17316.5950935243917346341.stgit@devbox
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masami Hiramatsu [Wed, 9 May 2018 12:58:15 +0000 (21:58 +0900)]
kprobes/x86: Prohibit probing on exception masking instructions
[ Upstream commit
ee6a7354a3629f9b65bc18dbe393503e9440d6f5 ]
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by kprobes must be
prohibited.
However, kprobes usually executes those instructions directly on trampoline
buffer (a.k.a. kprobe-booster), except for the kprobes which has
post_handler. Thus if kprobe user probes MOV SS with post_handler, it will
do single-stepping on the MOV SS.
This means it is safe that if it is used via ftrace or perf/bpf since those
don't use the post_handler.
Anyway, since the stack switching is a rare case, it is safer just
rejecting kprobes on such instructions.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Cc: Francis Deslauriers <francis.deslauriers@efficios.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Yonghong Song <yhs@fb.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "David S . Miller" <davem@davemloft.net>
Link: https://lkml.kernel.org/r/152587069574.17316.3311695234863248641.stgit@devbox
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ashish Samant [Fri, 11 May 2018 23:02:07 +0000 (16:02 -0700)]
ocfs2: take inode cluster lock before moving reflinked inode from orphan dir
[ Upstream commit
e4383029201470523c3ffe339bd7d57e9b4a7d65 ]
While reflinking an inode, we create a new inode in orphan directory,
then take EX lock on it, reflink the original inode to orphan inode and
release EX lock. Once the lock is released another node could request
it in EX mode from ocfs2_recover_orphans() which causes downconvert of
the lock, on this node, to NL mode.
Later we attempt to initialize security acl for the orphan inode and
move it to the reflink destination. However, while doing this we dont
take EX lock on the inode. This could potentially cause problems
because we could be starting transaction, accessing journal and
modifying metadata of the inode while holding NL lock and with another
node holding EX lock on the inode.
Fix this by taking orphan inode cluster lock in EX mode before
initializing security and moving orphan inode to reflink destination.
Use the __tracker variant while taking inode lock to avoid recursive
locking in the ocfs2_init_security_and_acl() call chain.
Link: http://lkml.kernel.org/r/1523475107-7639-1-git-send-email-ashish.samant@oracle.com
Signed-off-by: Ashish Samant <ashish.samant@oracle.com>
Reviewed-by: Joseph Qi <jiangqi903@gmail.com>
Reviewed-by: Junxiao Bi <junxiao.bi@oracle.com>
Acked-by: Jun Piao <piaojun@huawei.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Changwei Ge <ge.changwei@h3c.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laura Abbott [Fri, 11 May 2018 23:01:57 +0000 (16:01 -0700)]
proc/kcore: don't bounds check against address 0
[ Upstream commit
3955333df9a50e8783d115613a397ae55d905080 ]
The existing kcore code checks for bad addresses against __va(0) with
the assumption that this is the lowest address on the system. This may
not hold true on some systems (e.g. arm64) and produce overflows and
crashes. Switch to using other functions to validate the address range.
It's currently only seen on arm64 and it's not clear if anyone wants to
use that particular combination on a stable release. So this is not
urgent for stable.
Link: http://lkml.kernel.org/r/20180501201143.15121-1-labbott@redhat.com
Signed-off-by: Laura Abbott <labbott@redhat.com>
Tested-by: Dave Anderson <anderson@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>a
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeffrey Hugo [Fri, 11 May 2018 23:01:42 +0000 (16:01 -0700)]
init: fix false positives in W+X checking
[ Upstream commit
ae646f0b9ca135b87bc73ff606ef996c3029780a ]
load_module() creates W+X mappings via __vmalloc_node_range() (from
layout_and_allocate()->move_module()->module_alloc()) by using
PAGE_KERNEL_EXEC. These mappings are later cleaned up via
"call_rcu_sched(&freeinit->rcu, do_free_init)" from do_init_module().
This is a problem because call_rcu_sched() queues work, which can be run
after debug_checkwx() is run, resulting in a race condition. If hit,
the race results in a nasty splat about insecure W+X mappings, which
results in a poor user experience as these are not the mappings that
debug_checkwx() is intended to catch.
This issue is observed on multiple arm64 platforms, and has been
artificially triggered on an x86 platform.
Address the race by flushing the queued work before running the
arch-defined mark_rodata_ro() which then calls debug_checkwx().
Link: http://lkml.kernel.org/r/1525103946-29526-1-git-send-email-jhugo@codeaurora.org
Fixes:
e1a58320a38d ("x86/mm: Warn on W^X mappings")
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reported-by: Timur Tabi <timur@codeaurora.org>
Reported-by: Jan Glauber <jan.glauber@caviumnetworks.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Laura Abbott <labbott@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roman Mashak [Fri, 11 May 2018 14:55:09 +0000 (10:55 -0400)]
net sched actions: fix invalid pointer dereferencing if skbedit flags missing
[ Upstream commit
af5d01842fe1fbfb9f5e1c1d957ba02ab6f4569a ]
When application fails to pass flags in netlink TLV for a new skbedit action,
the kernel results in the following oops:
[ 8.307732] BUG: unable to handle kernel paging request at
0000000000021130
[ 8.309167] PGD
80000000193d1067 P4D
80000000193d1067 PUD
180e0067 PMD 0
[ 8.310595] Oops: 0000 [#1] SMP PTI
[ 8.311334] Modules linked in: kvm_intel kvm irqbypass crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd cryptd glue_helper serio_raw
[ 8.314190] CPU: 1 PID: 397 Comm: tc Not tainted 4.17.0-rc3+ #357
[ 8.315252] RIP: 0010:__tcf_idr_release+0x33/0x140
[ 8.316203] RSP: 0018:
ffffa0718038f840 EFLAGS:
00010246
[ 8.317123] RAX:
0000000000000001 RBX:
0000000000021100 RCX:
0000000000000000
[ 8.319831] RDX:
0000000000000000 RSI:
0000000000000000 RDI:
0000000000021100
[ 8.321181] RBP:
0000000000000000 R08:
000000000004adf8 R09:
0000000000000122
[ 8.322645] R10:
0000000000000000 R11:
ffffffff9e5b01ed R12:
0000000000000000
[ 8.324157] R13:
ffffffff9e0d3cc0 R14:
0000000000000000 R15:
0000000000000000
[ 8.325590] FS:
00007f591292e700(0000) GS:
ffff8fcf5bc40000(0000) knlGS:
0000000000000000
[ 8.327001] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
[ 8.327987] CR2:
0000000000021130 CR3:
00000000180e6004 CR4:
00000000001606a0
[ 8.329289] Call Trace:
[ 8.329735] tcf_skbedit_init+0xa7/0xb0
[ 8.330423] tcf_action_init_1+0x362/0x410
[ 8.331139] ? try_to_wake_up+0x44/0x430
[ 8.331817] tcf_action_init+0x103/0x190
[ 8.332511] tc_ctl_action+0x11a/0x220
[ 8.333174] rtnetlink_rcv_msg+0x23d/0x2e0
[ 8.333902] ? _cond_resched+0x16/0x40
[ 8.334569] ? __kmalloc_node_track_caller+0x5b/0x2c0
[ 8.335440] ? rtnl_calcit.isra.31+0xf0/0xf0
[ 8.336178] netlink_rcv_skb+0xdb/0x110
[ 8.336855] netlink_unicast+0x167/0x220
[ 8.337550] netlink_sendmsg+0x2a7/0x390
[ 8.338258] sock_sendmsg+0x30/0x40
[ 8.338865] ___sys_sendmsg+0x2c5/0x2e0
[ 8.339531] ? pagecache_get_page+0x27/0x210
[ 8.340271] ? filemap_fault+0xa2/0x630
[ 8.340943] ? page_add_file_rmap+0x108/0x200
[ 8.341732] ? alloc_set_pte+0x2aa/0x530
[ 8.342573] ? finish_fault+0x4e/0x70
[ 8.343332] ? __handle_mm_fault+0xbc1/0x10d0
[ 8.344337] ? __sys_sendmsg+0x53/0x80
[ 8.345040] __sys_sendmsg+0x53/0x80
[ 8.345678] do_syscall_64+0x4f/0x100
[ 8.346339] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 8.347206] RIP: 0033:0x7f591191da67
[ 8.347831] RSP: 002b:
00007fff745abd48 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
[ 8.349179] RAX:
ffffffffffffffda RBX:
00007fff745abe70 RCX:
00007f591191da67
[ 8.350431] RDX:
0000000000000000 RSI:
00007fff745abdc0 RDI:
0000000000000003
[ 8.351659] RBP:
000000005af35251 R08:
0000000000000001 R09:
0000000000000000
[ 8.352922] R10:
00000000000005f1 R11:
0000000000000246 R12:
0000000000000000
[ 8.354183] R13:
00007fff745afed0 R14:
0000000000000001 R15:
00000000006767c0
[ 8.355400] Code: 41 89 d4 53 89 f5 48 89 fb e8 aa 20 fd ff 85 c0 0f 84 ed 00
00 00 48 85 db 0f 84 cf 00 00 00 40 84 ed 0f 85 cd 00 00 00 45 84 e4 <8b> 53 30
74 0d 85 d2 b8 ff ff ff ff 0f 8f b3 00 00 00 8b 43 2c
[ 8.358699] RIP: __tcf_idr_release+0x33/0x140 RSP:
ffffa0718038f840
[ 8.359770] CR2:
0000000000021130
[ 8.360438] ---[ end trace
60c66be45dfc14f0 ]---
The caller calls action's ->init() and passes pointer to "struct tc_action *a",
which later may be initialized to point at the existing action, otherwise
"struct tc_action *a" is still invalid, and therefore dereferencing it is an
error as happens in tcf_idr_release, where refcnt is decremented.
So in case of missing flags tcf_idr_release must be called only for
existing actions.
v2:
- prepare patch for net tree
Fixes:
5e1567aeb7fe ("net sched: skbedit action fix late binding")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emil Tantilov [Fri, 20 Apr 2018 00:06:57 +0000 (17:06 -0700)]
ixgbe: return error on unsupported SFP module when resetting
[ Upstream commit
bbb2707623f3ccc48695da2433f06d7c38193451 ]
Add check for unsupported module and return the error code.
This fixes a Coverity hit due to unused return status from setup_sfp.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marian Rotariu [Mon, 30 Apr 2018 09:23:01 +0000 (12:23 +0300)]
x86: Delay skip of emulated hypercall instruction
[ Upstream commit
6356ee0c9602004e0a3b4b2dad68ee2ee9385b17 ]
The IP increment should be done after the hypercall emulation, after
calling the various handlers. In this way, these handlers can accurately
identify the the IP of the VMCALL if they need it.
This patch keeps the same functionality for the Hyper-V handler which does
not use the return code of the standard kvm_skip_emulated_instruction()
call.
Signed-off-by: Marian Rotariu <mrotariu@bitdefender.com>
[Hyper-V hypercalls also need kvm_skip_emulated_instruction() - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wanpeng Li [Fri, 27 Apr 2018 00:55:03 +0000 (17:55 -0700)]
KVM: Extend MAX_IRQ_ROUTES to 4096 for all archs
[ Upstream commit
ddc9cfb79c1096a0855839631c091aa7e9602052 ]
Our virtual machines make use of device assignment by configuring
12 NVMe disks for high I/O performance. Each NVMe device has 129
MSI-X Table entries:
Capabilities: [50] MSI-X: Enable+ Count=129 Masked-Vector table: BAR=0 offset=
00002000
The windows virtual machines fail to boot since they will map the number of
MSI-table entries that the NVMe hardware reported to the bus to msi routing
table, this will exceed the 1024. This patch extends MAX_IRQ_ROUTES to 4096
for all archs, in the future this might be extended again if needed.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim KrÄmář <rkrcmar@redhat.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Tonny Lu <tonnylu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Thu, 10 May 2018 22:26:01 +0000 (23:26 +0100)]
rxrpc: Fix the min security level for kernel calls
[ Upstream commit
93864fc3ffcc4bf70e96cfb5cc6e941630419ad0 ]
Fix the kernel call initiation to set the minimum security level for kernel
initiated calls (such as from kAFS) from the sockopt value.
Fixes:
19ffa01c9c45 ("rxrpc: Use structs to hold connection params and protocol info")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Thu, 10 May 2018 22:26:00 +0000 (23:26 +0100)]
rxrpc: Fix error reception on AF_INET6 sockets
[ Upstream commit
f2aeed3a591ff29a82495eeaa92ac4780bad7487 ]
AF_RXRPC tries to turn on IP_RECVERR and IP_MTU_DISCOVER on the UDP socket
it just opened for communications with the outside world, regardless of the
type of socket. Unfortunately, this doesn't work with an AF_INET6 socket.
Fix this by turning on IPV6_RECVERR and IPV6_MTU_DISCOVER instead if the
socket is of the AF_INET6 family.
Without this, kAFS server and address rotation doesn't work correctly
because the algorithm doesn't detect received network errors.
Fixes:
75b54cb57ca3 ("rxrpc: Add IPv6 support")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>