Jonathan Bell [Mon, 16 May 2022 09:28:27 +0000 (10:28 +0100)]
mmc: block: Don't do single-sector reads during recovery
See https://github.com/raspberrypi/linux/issues/5019
If an SD card has degraded performance such that IO operations time out
then the MMC block layer will leak SG DMA mappings in the swiotlb during
recovery. It retries the same SG and this causes the leak, as it is
mapped twice - once in sdhci_pre_req() and again during single-block
reads in sdhci_prepare_data().
Resetting the card (including power-cycling if a regulator for vmmc is
present) ought to be enough to recover a stuck state, so for now don't
try single-block reads in the recovery path.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
gellert [Fri, 15 Aug 2014 15:35:06 +0000 (16:35 +0100)]
MMC: added alternative MMC driver
mmc: Disable CMD23 transfers on all cards
Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.
Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>
mmc: bcm2835-mmc: enable DT support for all architectures
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
mmc: bcm2835-mmc: fix probe error handling
Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Add locks when accessing sdhost registers
bcm2835-mmc: Add range of debug options for slowing things down
bcm2835-mmc: Add option to disable some delays
bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23
bcm2835-mmc: Adding overclocking option
Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.
Use at your own risk.
bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz
Also only warn once for each overclock setting.
mmc: bcm2835-mmc: Make available on ARCH_BCM2835
Make the bcm2835-mmc driver available for use on ARCH_BCM2835.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-mmc entry
Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-mmc: Don't overwrite MMC capabilities from DT
bcm2835-mmc: Don't override bus width capabilities from devicetree
Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.
bcm2835-mmc: Only claim one DMA channel
With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.
See: https://github.com/raspberrypi/linux/issues/1327
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: New timer API
mmc: bcm2835-mmc: Support underclocking
Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.
See: https://github.com/raspberrypi/linux/issues/2350
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mmc/bcm2835: Recover from MMC_SEND_EXT_CSD
If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.
A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.
N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.
See: https://github.com/raspberrypi/linux/issues/2728
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: Fix DMA channel leak
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.
I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix struct mmc_host leak on probe
The BCM2835 MMC host driver requests the bus address of the host's
register map on probe. If that fails, the driver leaks the struct
mmc_host allocated earlier.
Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Fix duplicate free_irq() on remove
The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.
However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.
The interrupt is thus freed twice, leading to a WARN splat in
__free_irq(). Fix by not requesting the interrupt as a device-managed
resource.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Handle mmc_add_host() errors
The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value. Errors occurring in that function are therefore not
handled. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835-mmc: Deduplicate reset of driver data on remove
The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver(). Drop the duplicate assignment.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
bcm2835_mmc: Remove vestigial threaded IRQ
With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.
Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>
mmc: sdhci: Silence MMC warnings
When the MMC isn't plugged in, the driver will spam the console which is
pretty annoying when using NFS.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
mmc: sdhci-iproc: Fix vmmc regulators on iProc
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour. Borrow the implementation
from sdhci_arasan_set_power.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-mmc: uninitialized_var is no more
Revert "mmc: sdhci-iproc: Fix vmmc regulators on iProc"
This reverts commit
aed19399a01733dbad9be8bf026a4f7dd823b04f.
Commit
6c92ae1e452f ("mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()")
introduced a generic helper that does the same thing so use that instead in
the following commit.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
mmc: sdhci-iproc: Fix vmmc regulators (pre-bcm2711)
The Linux support for controlling card power via regulators appears to
be contentious. I would argue that the default behaviour is contrary to
the SDHCI spec - turning off the power writes a reserved value to the
SD Bus Voltage Select field of the Power Control Register, which
seems to kill the Arasan/iProc controller - but fortunately there is a
hook in sdhci_ops to override the behaviour.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-mmc: Honor return value of mmc_of_parse()
bcm2835_mmc_probe() ignores errors returned by mmc_of_parse() and in
particular ignores -EPROBE_DEFER, which may be returned if the power
sequencing driver configured in the devicetree is compiled as a module.
The user-visible result is that access to the SDIO device fails because
its power sequencing requirements have not been observed. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
bcm2835-mmc: Use phys addresses for slave DMA config
Contrary to what struct snd_dmaengine_dai_dma_data suggests, the
configuration of addresses of DMA slave interfaces should be done in
CPU physical addresses.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Florian Meier [Fri, 22 Nov 2013 13:22:53 +0000 (14:22 +0100)]
dmaengine: Add support for BCM2708
Add support for DMA controller of BCM2708 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels
DMA: fix cyclic LITE length overflow bug
dmaengine: bcm2708: Remove chancnt affectations
Mirror bcm2835-dma.c commit
9eba5536a7434c69d8c185d4bd1c70734d92287d:
chancnt is already filled by dma_async_device_register, which uses the channel
list to know how much channels there is.
Since it's already filled, we can safely remove it from the drivers' probe
function.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: overwrite dreq only if it is not set
dreq is set when the DMA channel is fetched from Device Tree.
slave_id is set using dmaengine_slave_config().
Only overwrite dreq with slave_id if it is not set.
dreq/slave_id in the cyclic DMA case is not touched, because I don't
have hardware to test with.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: do device registration in the board file
Don't register the device in the driver. Do it in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835
Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Add Device Tree support to the non ARCH_BCM2835 case.
Use the same driver name regardless of architecture.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: add bcm2835-dma entry
Add Device Tree entry for bcm2835-dma.
The entry doesn't contain any resources since they are handled
by the arch/arm/mach-bcm270x/dma.c driver.
In non-DT mode, don't add the device in the board file.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine: Add debug options
BCM270x: Add memory and irq resources to dmaengine device and DT
Prepare for merging of the legacy DMA API arch driver dma.c
with bcm2708-dmaengine by adding memory and irq resources both
to platform file device and Device Tree node.
Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c
Merge the legacy DMA API driver with bcm2708-dmaengine.
This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox
driver is also needed).
Changes to the dma.c code:
- Use BIT() macro.
- Cutdown some comments to one line.
- Add mutex to vc_dmaman and use this, since the dev lock is locked
during probing of the engine part.
- Add global g_dmaman variable since drvdata is used by the engine part.
- Restructure for readability:
vc_dmaman_chan_alloc()
vc_dmaman_chan_free()
bcm_dma_chan_free()
- Restructure bcm_dma_chan_alloc() to simplify error handling.
- Use device irq resources instead of hardcoded bcm_dma_irqs table.
- Remove dev_dmaman_register() and code it directly.
- Remove dev_dmaman_deregister() and code it directly.
- Simplify bcm_dmaman_probe() using devm_* functions.
- Get dmachans from DT if available.
- Keep 'dma.dmachans' module argument name for backwards compatibility.
Make it available on ARCH_BCM2835 as well.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: set residue_granularity field
bcm2708-dmaengine supports residue reporting at burst level
but didn't report this via the residue_granularity field.
Without this field set properly we get playback issues with I2S cards.
dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer
bcm2708-dmaengine: Use more DMA channels (but not 12)
1) Only the bcm2708_fb drivers uses the legacy DMA API, and
it requires a BULK-capable channel, so all other types
(FAST, NORMAL and LITE) can be made available to the regular
DMA API.
2) DMA channels 11-14 share an interrupt. The driver can't
handle this, so don't use channels 12-14 (12 was used, probably
because it appears to have an interrupt, but in reality that
interrupt is for activity on ANY channel). This may explain
a lockup encountered when running out of DMA channels.
The combined effect of this patch is to leave 7 DMA channels
available + channel 0 for bcm2708_fb via the legacy API.
See: https://github.com/raspberrypi/linux/issues/1110
https://github.com/raspberrypi/linux/issues/1108
dmaengine: bcm2708: Make legacy API available for bcm2835-dma
bcm2708_fb uses the legacy DMA API, so in order to start using
bcm2835-dma, bcm2835-dma has to support the legacy API. Make this
possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove().
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Change DT compatible string
Both bcm2835-dma and bcm2708-dmaengine have the same compatible string.
So change compatible to "brcm,bcm2708-dma".
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dmaengine: bcm2708: Remove driver but keep legacy API
Dropping non-DT support means we don't need this driver,
but we still need the legacy DMA API.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2708-dmaengine - Fix arm64 portability/build issues
dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708
bcm2708-dmaengine.c defines functions like bcm_dma_start which are
defined as well in dma-bcm2708.h as inline versions when
CONFIG_DMA_BCM2708 is not defined. This works fine when
CONFIG_DMA_BCM2708 is built in, but when it is selected as module build
fails with redefinition errors because in the build system when
CONFIG_DMA_BCM2708 is selected as module, the macro becomes
CONFIG_DMA_BCM2708_MODULE.
This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when
available.
Fixes https://github.com/raspberrypi/linux/issues/2056
Signed-off-by: Andrei Gherzan <andrei@gherzan.com>
bcm2708-dmaengine: Use platform_get_irq
The platform driver framework no longer creates IRQ resources for
platform devices because they are expected to use platform_get_irq.
This causes the bcm2808_fb acceleration to fail.
Fix the problem by calling platform_get_irq as intended.
See: https://github.com/raspberrypi/linux/issues/5131
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Siarhei Siamashka [Mon, 17 Jun 2013 10:32:11 +0000 (13:32 +0300)]
fbdev: add FBIOCOPYAREA ioctl
Based on the patch authored by Ali Gholami Rudi at
https://lkml.org/lkml/2009/7/13/153
Provide an ioctl for userspace applications, but only if this operation
is hardware accelerated (otherwide it does not make any sense).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: Add ioctl for reading gpu memory through dma
video: bcm2708_fb: Add compat_ioctl support.
When using a 64 bit kernel with 32 bit userspace we need
compat ioctl handling for FBIODMACOPY as one of the
parameters is a pointer.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
James Hughes [Thu, 14 Mar 2019 13:27:54 +0000 (13:27 +0000)]
Pulled in the multi frame buffer support from the Pi3 repo
popcornmix [Wed, 17 Jun 2015 16:06:34 +0000 (17:06 +0100)]
bcm2708 framebuffer driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
bcm2708_fb : Implement blanking support using the mailbox property interface
bcm2708_fb: Add pan and vsync controls
bcm2708_fb: DMA acceleration for fb_copyarea
Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425
Also used Simon's dmaer_master module as a reference for tweaking DMA
settings for better performance.
For now busylooping only. IRQ support might be added later.
With non-overclocked Raspberry Pi, the performance is ~360 MB/s
for simple copy or ~260 MB/s for two-pass copy (used when dragging
windows to the right).
In the case of using DMA channel 0, the performance improves
to ~440 MB/s.
For comparison, VFP optimized CPU copy can only do ~114 MB/s in
the same conditions (hindered by reading uncached source buffer).
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
bcm2708_fb: report number of dma copies
Add a counter (exported via debugfs) reporting the
number of dma copies that the framebuffer driver
has done, in order to help evaluate different
optimization strategies.
Signed-off-by: Luke Diamand <luked@broadcom.com>
bcm2708_fb: use IRQ for DMA copies
The copyarea ioctl() uses DMA to speed things along. This
was busy-waiting for completion. This change supports using
an interrupt instead for larger transfers. For small
transfers, busy-waiting is still likely to be faster.
Signed-off-by: Luke Diamand <luke@diamand.org>
bcm2708: Make ioctl logging quieter
video: fbdev: bcm2708_fb: Don't panic on error
No need to panic the kernel if the video driver fails.
Just print a message and return an error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
fbdev: bcm2708_fb: Add ARCH_BCM2835 support
Add Device Tree support.
Pass the device to dma_alloc_coherent() in order to get the
correct bus address on ARCH_BCM2835.
Use the new DMA legacy API header file.
Including <mach/platform.h> is not necessary.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270x_DT: Add bcm2708-fb device
Add bcm2708-fb to Device Tree and don't add the
platform device when booting in DT mode.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Cleanup of bcm2708_fb file to kernel coding standards
Some minor change to function - remove a use of
in_atomic, plus replacing various debug messages
that manually specify the function name with
("%s",.__func__)
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
video: bcm2708_fb: Try allocating on the ARM and passing to VPU
Currently the VPU allocates the contiguous buffer for the
framebuffer.
Try an alternate path first where we use dma_alloc_coherent
and pass the buffer to the VPU. Should the VPU firmware not
support that path, then free the buffer and revert to the
old behaviour of using the VPU allocation.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
popcornmix [Wed, 1 May 2013 18:46:17 +0000 (19:46 +0100)]
Add dwc_otg driver
Signed-off-by: popcornmix <popcornmix@gmail.com>
usb: dwc: fix lockdep false positive
Signed-off-by: Kari Suvanto <karis79@gmail.com>
usb: dwc: fix inconsistent lock state
Signed-off-by: Kari Suvanto <karis79@gmail.com>
Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance.
Thanks to Gordon and Costas
Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005.
Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh
Make sure we wait for the reset to finish
dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel
memory corruption, escalating to OOPS under high USB load.
dwc_otg: Fix unsafe access of QTD during URB enqueue
In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the
transaction could complete almost immediately after the qtd was assigned
to a host channel during URB enqueue, which meant the qtd pointer was no
longer valid having been completed and removed. Usually, this resulted in
an OOPS during URB submission. By predetermining whether transactions
need to be queued or not, this unsafe pointer access is avoided.
This bug was only evident on the Pi model A where a device was attached
that had no periodic endpoints (e.g. USB pendrive or some wlan devices).
dwc_otg: Fix incorrect URB allocation error handling
If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS
because for some reason a member of the *unallocated* struct was set to
zero. Error handling changed to fail correctly.
dwc_otg: fix potential use-after-free case in interrupt handler
If a transaction had previously aborted, certain interrupts are
enabled to track error counts and reset where necessary. On IN
endpoints the host generates an ACK interrupt near-simultaneously
with completion of transfer. In the case where this transfer had
previously had an error, this results in a use-after-free on
the QTD memory space with a 1-byte length being overwritten to
0x00.
dwc_otg: add handling of SPLIT transaction data toggle errors
Previously a data toggle error on packets from a USB1.1 device behind
a TT would result in the Pi locking up as the driver never handled
the associated interrupt. Patch adds basic retry mechanism and
interrupt acknowledgement to cater for either a chance toggle error or
for devices that have a broken initial toggle state (FT8U232/FT232BM).
dwc_otg: implement tasklet for returning URBs to usbcore hcd layer
The dwc_otg driver interrupt handler for transfer completion will spend
a very long time with interrupts disabled when a URB is completed -
this is because usb_hcd_giveback_urb is called from within the handler
which for a USB device driver with complicated processing (e.g. webcam)
will take an exorbitant amount of time to complete. This results in
missed completion interrupts for other USB packets which lead to them
being dropped due to microframe overruns.
This patch splits returning the URB to the usb hcd layer into a
high-priority tasklet. This will have most benefit for isochronous IN
transfers but will also have incidental benefit where multiple periodic
devices are active at once.
dwc_otg: fix NAK holdoff and allow on split transactions only
This corrects a bug where if a single active non-periodic endpoint
had at least one transaction in its qh, on frnum == MAX_FRNUM the qh
would get skipped and never get queued again. This would result in
a silent device until error detection (automatic or otherwise) would
either reset the device or flush and requeue the URBs.
Additionally the NAK holdoff was enabled for all transactions - this
would potentially stall a HS endpoint for 1ms if a previous error state
enabled this interrupt and the next response was a NAK. Fix so that
only split transactions get held off.
dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler
usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it
asynchronously in the tasklet was not safe (regression in
c4564d4a1a0a9b10d4419e48239f5d99e88d2667).
This change unlinks it from the endpoint prior to queueing it for handling in
the tasklet, and also adds a check to ensure the urb is OK to be unlinked
before doing so.
NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb
when a USB device was unplugged/replugged during data transfer. This effect
was reproduced using automated USB port power control, hundreds of replug
events were performed during active transfers to confirm that the problem was
eliminated.
USB fix using a FIQ to implement split transactions
This commit adds a FIQ implementaion that schedules
the split transactions using a FIQ so we don't get
held off by the interrupt latency of Linux
dwc_otg: fix device attributes and avoid kernel warnings on boot
dcw_otg: avoid logging function that can cause panics
See: https://github.com/raspberrypi/firmware/issues/21
Thanks to cleverca22 for fix
dwc_otg: mask correct interrupts after transaction error recovery
The dwc_otg driver will unmask certain interrupts on a transaction
that previously halted in the error state in order to reset the
QTD error count. The various fine-grained interrupt handlers do not
consider that other interrupts besides themselves were unmasked.
By disabling the two other interrupts only ever enabled in DMA mode
for this purpose, we can avoid unnecessary function calls in the
IRQ handler. This will also prevent an unneccesary FIQ interrupt
from being generated if the FIQ is enabled.
dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ
In the case of a transaction to a device that had previously aborted
due to an error, several interrupts are enabled to reset the error
count when a device responds. This has the side-effect of making the
FIQ thrash because the hardware will generate multiple instances of
a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK
on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the
associated interrupts.
Additionally, on non-split transactions make sure that only unmasked
interrupts are cleared. This caused a hard-to-trigger but serious
race condition when you had the combination of an endpoint awaiting
error recovery and a transaction completed on an endpoint - due to
the sequencing and timing of interrupts generated by the dwc_otg core,
it was possible to confuse the IRQ handler.
Fix function tracing
dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue
dwc_otg: prevent OOPSes during device disconnects
The dwc_otg_urb_enqueue function is thread-unsafe. In particular the
access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and
friends does not occur within a critical section and so if a device
was unplugged during activity there was a high chance that the
usbcore hub_thread would try to disable the endpoint with partially-
formed entries in the URB queue. This would result in BUG() or null
pointer dereferences.
Fix so that access of urb->hcpriv, enqueuing to the hardware and
adding to usbcore endpoint URB lists is contained within a single
critical section.
dwc_otg: prevent BUG() in TT allocation if hub address is > 16
A fixed-size array is used to track TT allocation. This was
previously set to 16 which caused a crash because
dwc_otg_hcd_allocate_port would read past the end of the array.
This was hit if a hub was plugged in which enumerated as addr > 16,
due to previous device resets or unplugs.
Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows
to a large size if 128 hub addresses are supported. This field is
for debug only for tracking which frame an allocate happened in.
dwc_otg: make channel halts with unknown state less damaging
If the IRQ received a channel halt interrupt through the FIQ
with no other bits set, the IRQ would not release the host
channel and never complete the URB.
Add catchall handling to treat as a transaction error and retry.
dwc_otg: fiq_split: use TTs with more granularity
This fixes certain issues with split transaction scheduling.
- Isochronous multi-packet OUT transactions now hog the TT until
they are completed - this prevents hubs aborting transactions
if they get a periodic start-split out-of-order
- Don't perform TT allocation on non-periodic endpoints - this
allows simultaneous use of the TT's bulk/control and periodic
transaction buffers
This commit will mainly affect USB audio playback.
dwc_otg: fix potential sleep while atomic during urb enqueue
Fixes a regression introduced with
eb1b482a. Kmalloc called from
dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have
the GPF_ATOMIC flag set. Force this flag when inside the larger
critical section.
dwc_otg: make fiq_split_enable imply fiq_fix_enable
Failing to set up the FIQ correctly would result in
"IRQ 32: nobody cared" errors in dmesg.
dwc_otg: prevent crashes on host port disconnects
Fix several issues resulting in crashes or inconsistent state
if a Model A root port was disconnected.
- Clean up queue heads properly in kill_urbs_in_qh_list by
removing the empty QHs from the schedule lists
- Set the halt status properly to prevent IRQ handlers from
using freed memory
- Add fiq_split related cleanup for saved registers
- Make microframe scheduling reclaim host channels if
active during a disconnect
- Abort URBs with -ESHUTDOWN status response, informing
device drivers so they respond in a more correct fashion
and don't try to resubmit URBs
- Prevent IRQ handlers from attempting to handle channel
interrupts if the associated URB was dequeued (and the
driver state was cleared)
dwc_otg: prevent leaking URBs during enqueue
A dwc_otg_urb would get leaked if the HCD enqueue function
failed for any reason. Free the URB at the appropriate points.
dwc_otg: Enable NAK holdoff for control split transactions
Certain low-speed devices take a very long time to complete a
data or status stage of a control transaction, producing NAK
responses until they complete internal processing - the USB2.0
spec limit is up to 500mS. This causes the same type of interrupt
storm as seen with USB-serial dongles prior to
c8edb238.
In certain circumstances, usually while booting, this interrupt
storm could cause SD card timeouts.
dwc_otg: Fix for occasional lockup on boot when doing a USB reset
dwc_otg: Don't issue traffic to LS devices in FS mode
Issuing low-speed packets when the root port is in full-speed mode
causes the root port to stop responding. Explicitly fail when
enqueuing URBs to a LS endpoint on a FS bus.
Fix ARM architecture issue with local_irq_restore()
If local_fiq_enable() is called before a local_irq_restore(flags) where
the flags variable has the F bit set, the FIQ will be erroneously disabled.
Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR.
Also fix some of the hacks previously implemented for previous dwc_otg
incarnations.
dwc_otg: fiq_fsm: Base commit for driver rewrite
This commit removes the previous FIQ fixes entirely and adds fiq_fsm.
This rewrite features much more complete support for split transactions
and takes into account several OTG hardware bugs. High-speed
isochronous transactions are also capable of being performed by fiq_fsm.
All driver options have been removed and replaced with:
- dwc_otg.fiq_enable (bool)
- dwc_otg.fiq_fsm_enable (bool)
- dwc_otg.fiq_fsm_mask (bitmask)
- dwc_otg.nak_holdoff (unsigned int)
Defaults are specified such that fiq_fsm behaves similarly to the
previously implemented FIQ fixes.
fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used
If the transfer associated with a QTD failed due to a bus error, the HCD
would retry the transfer up to 3 times (implementing the USB2.0
three-strikes retry in software).
Due to the masking mechanism used by fiq_fsm, it is only possible to pass
a single interrupt through to the HCD per-transfer.
In this instance host channels would fall off the radar because the error
reset would function, but the subsequent channel halt would be lost.
Push the error count reset into the FIQ handler.
fiq_fsm: Implement timeout mechanism
For full-speed endpoints with a large packet size, interrupt latency
runs the risk of the FIQ starting a transaction too late in a full-speed
frame. If the device is still transmitting data when EOF2 for the
downstream frame occurs, the hub will disable the port. This change is
not reflected in the hub status endpoint and the device becomes
unresponsive.
Prevent high-bandwidth transactions from being started too late in a
frame. The mechanism is not guaranteed: a combination of bit stuffing
and hub latency may still result in a device overrunning.
fiq_fsm: fix bounce buffer utilisation for Isochronous OUT
Multi-packet isochronous OUT transactions were subject to a few bounday
bugs. Fix them.
Audio playback is now much more robust: however, an issue stands with
devices that have adaptive sinks - ALSA plays samples too fast.
dwc_otg: Return full-speed frame numbers in HS mode
The frame counter increments on every *microframe* in high-speed mode.
Most device drivers expect this number to be in full-speed frames - this
caused considerable confusion to e.g. snd_usb_audio which uses the
frame counter to estimate the number of samples played.
fiq_fsm: save PID on completion of interrupt OUT transfers
Also add edge case handling for interrupt transports.
Note that for periodic split IN, data toggles are unimplemented in the
OTG host hardware - it unconditionally accepts any PID.
fiq_fsm: add missing case for fiq_fsm_tt_in_use()
Certain combinations of bitrate and endpoint activity could
result in a periodic transaction erroneously getting started
while the previous Isochronous OUT was still active.
fiq_fsm: clear hcintmsk for aborted transactions
Prevents the FIQ from erroneously handling interrupts
on a timed out channel.
fiq_fsm: enable by default
fiq_fsm: fix dequeues for non-periodic split transactions
If a dequeue happened between the SSPLIT and CSPLIT phases of the
transaction, the HCD would never receive an interrupt.
fiq_fsm: Disable by default
fiq_fsm: Handle HC babble errors
The HCTSIZ transfer size field raises a babble interrupt if
the counter wraps. Handle the resulting interrupt in this case.
dwc_otg: fix interrupt registration for fiq_enable=0
Additionally make the module parameter conditional for wherever
hcd->fiq_state is touched.
fiq_fsm: Enable by default
dwc_otg: Fix various issues with root port and transaction errors
Process the host port interrupts correctly (and don't trample them).
Root port hotplug now functional again.
Fix a few thinkos with the transaction error passthrough for fiq_fsm.
fiq_fsm: Implement hack for Split Interrupt transactions
Hubs aren't too picky about which endpoint we send Control type split
transactions to. By treating Interrupt transfers as Control, it is
possible to use the non-periodic queue in the OTG core as well as the
non-periodic FIFOs in the hub itself. This massively reduces the
microframe exclusivity/contention that periodic split transactions
otherwise have to enforce.
It goes without saying that this is a fairly egregious USB specification
violation, but it works.
Original idea by Hans Petter Selasky @ FreeBSD.org.
dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only.
dwc_otg: introduce fiq_fsm_spin(un|)lock()
SMP safety for the FIQ relies on register read-modify write cycles being
completed in the correct order. Several places in the DWC code modify
registers also touched by the FIQ. Protect these by a bare-bones lock
mechanism.
This also makes it possible to run the FIQ and IRQ handlers on different
cores.
fiq_fsm: fix build on bcm2708 and bcm2709 platforms
dwc_otg: put some barriers back where they should be for UP
bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active
dwc_otg: fixup read-modify-write in critical paths
Be more careful about read-modify-write on registers that the FIQ
also touches.
Guard fiq_fsm_spin_lock with fiq_enable check
fiq_fsm: Falling out of the state machine isn't fatal
This edge case can be hit if the port is disabled while the FIQ is
in the middle of a transaction. Make the effects less severe.
Also get rid of the useless return value.
squash: dwc_otg: Allow to build without SMP
usb: core: make overcurrent messages more prominent
Hub overcurrent messages are more serious than "debug". Increase loglevel.
usb: dwc_otg: Don't use dma_to_virt()
Commit 6ce0d20 changes dma_to_virt() which breaks this driver.
Open code the old dma_to_virt() implementation to work around this.
Limit the use of __bus_to_virt() to cases where transfer_buffer_length
is set and transfer_buffer is not set. This is done to increase the
chance that this driver will also work on ARCH_BCM2835.
transfer_buffer should not be NULL if the length is set, but the
comment in the code indicates that there are situations where this
might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar
comment pointing to a possible: 'usb storage / SCSI bug'.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Fix crash when fiq_enable=0
dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly
Certain low-bandwidth high-speed USB devices (specialist audio devices,
compressed-frame webcams) have packet intervals > 1 microframe.
Stride these transfers in the FIQ by using the start-of-frame interrupt
to restart the channel at the right time.
dwc_otg: Force host mode to fix incorrect compute module boards
dwc_otg: Add ARCH_BCM2835 support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Simplify FIQ irq number code
Dropping ATAGS means we can simplify the FIQ irq number code.
Also add error checking on the returned irq number.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: Remove duplicate gadget probe/unregister function
dwc_otg: Properly set the HFIR
Douglas Anderson reported:
According to the most up to date version of the dwc2 databook, the FRINT
field of the HFIR register should be programmed to:
* 125 us * (PHY clock freq for HS) - 1
* 1000 us * (PHY clock freq for FS/LS) - 1
This is opposed to older versions of the doc that claimed it should be:
* 125 us * (PHY clock freq for HS)
* 1000 us * (PHY clock freq for FS/LS)
and reported lower timing jitter on a USB analyser
dcw_otg: trim xfer length when buffer larger than allocated size is received
dwc_otg: Don't free qh align buffers in atomic context
dwc_otg: Enable the hack for Split Interrupt transactions by default
dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues.
So far we are aware of many success stories but no failure caused by this setting.
Make it a default to learn more.
See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: Use kzalloc when suitable
dwc_otg: Pass struct device to dma_alloc*()
This makes it possible to get the bus address from Device Tree.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
dwc_otg: fix summarize urb->actual_length for isochronous transfers
Kernel does not copy input data of ISO transfers to userspace
if actual_length is set only in ISO transfers and not summarized
in urb->actual_length. Fixes raspberrypi/linux#903
fiq_fsm: Use correct states when starting isoc OUT transfers
In fiq_fsm_start_next_periodic() if an isochronous OUT transfer
was selected, no regard was given as to whether this was a single-packet
transfer or a multi-packet staged transfer.
For single-packet transfers, this had the effect of repeatedly sending
OUT packets with bogus data and lengths.
Eventually if the channel was repeatedly enabled enough times, this
would lock up the OTG core and no further bus transfers would happen.
Set the FSM state up properly if we select a single-packet transfer.
Fixes https://github.com/raspberrypi/linux/issues/1842
dwc_otg: make nak_holdoff work as intended with empty queues
If URBs reading from non-periodic split endpoints were dequeued and
the last transfer from the endpoint was a NAK handshake, the resulting
qh->nak_frame value was stale which would result in unnecessarily long
polling intervals for the first subsequent transfer with a fresh URB.
Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against
a case where a single URB is submitted to the endpoint, a NAK was
received on the transfer immediately prior to receiving data and the
device subsequently resubmits another URB past the qh->nak_frame interval.
Fixes https://github.com/raspberrypi/linux/issues/1709
dwc_otg: fix split transaction data toggle handling around dequeues
See https://github.com/raspberrypi/linux/issues/1709
Fix several issues regarding endpoint state when URBs are dequeued
- If the HCD is disconnected, flush FIQ-enabled channels properly
- Save the data toggle state for bulk endpoints if the last transfer
from an endpoint where URBs were dequeued returned a data packet
- Reset hc->start_pkt_count properly in assign_and_init_hc()
dwc_otg: fix several potential crash sources
On root port disconnect events, the host driver state is cleared and
in-progress host channels are forcibly stopped. This doesn't play
well with the FIQ running in the background, so:
- Guard the disconnect callback with both the host spinlock and FIQ
spinlock
- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out
so we don't dereference a qtd that has gone away
- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings.
dwc_otg: delete hcd->channel_lock
The lock serves no purpose as it is only held while the HCD spinlock
is already being held.
dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt
Host channels are already halted in kill_urbs_in_qh_list() with the
subsequent interrupt processing behaving as if the URB was dequeued
via HCD callback.
There's no need to clobber the host channel registers a second time
as this exposes races between the driver and host channel resulting
in hcd->free_hc_list becoming corrupted.
dwcotg: Allow to build without FIQ on ARM64
Signed-off-by: popcornmix <popcornmix@gmail.com>
dwc_otg: make periodic scheduling behave properly for FS buses
If the root port is in full-speed mode, transfer times at 12mbit/s
would be calculated but matched against high-speed quotas.
Reinitialise hcd->frame_usecs[i] on each port enable event so that
full-speed bandwidth can be tracked sensibly.
Also, don't bother using the FIQ for transfers when in full-speed
mode - at the slower bus speed, interrupt frequency is reduced by
an order of magnitude.
Related issue: https://github.com/raspberrypi/linux/issues/2020
dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly
Get rid of the spammy printk and local pointer mangling.
Also, there is a nominal benefit for using fiq_fsm for isochronous
transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second)
so remove the root port speed check.
dwc_otg: add module parameter int_ep_interval_min
Add a module parameter (defaulting to ignored) that clamps the polling rate
of high-speed Interrupt endpoints to a minimum microframe interval.
The parameter is modifiable at runtime as it is used when activating new
endpoints (such as on device connect).
dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints
Certain hub types do not discriminate between pipe direction (IN or OUT)
when considering non-periodic transfers. Therefore these hubs get confused
if multiple transfers are issued in different directions with the same
device address and endpoint number.
Constrain queuing non-periodic split transactions so they are performed
serially in such cases.
Related: https://github.com/raspberrypi/linux/issues/2024
dwc_otg: Fixup change to DRIVER_ATTR interface
dwc_otg: Fix compilation warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
USB_DWCOTG: Disable building dwc_otg as a module (#2265)
When dwc_otg is built as a module, build will fail with the following
error:
ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined!
scripts/Makefile.modpost:91: recipe for target '__modpost' failed
make[1]: *** [__modpost] Error 1
Makefile:1199: recipe for target 'modules' failed
make: *** [modules] Error 2
Even if the error is solved by including the missing
DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading
dwc_otg.
As a workaround, simply prevent user from building dwc_otg as a module
as the current kernel does not support it.
See: https://github.com/raspberrypi/linux/issues/2258
Signed-off-by: Malik Olivier Boussejra <malik@boussejra.com>
dwc_otg: New timer API
dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE
dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init()
Add the ability to disable force_host_mode for those that want to use
dwc_otg in both device and host modes.
dwc_otg: Fix a regression when dequeueing isochronous transfers
In
282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues)
the dequeue mechanism was changed to leave FIQ-enabled transfers to run
to completion - to avoid leaving hub TT buffers with stale packets lying
around.
This broke FIQ-accelerated isochronous transfers, as this then meant that
dozens of transfers were performed after the dequeue function returned.
Restore the state machine fence for isochronous transfers.
fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288)
See: https://github.com/raspberrypi/linux/issues/2140
dwc_otg: add smp_mb() to prevent driver state corruption on boot
Occasional crashes have been seen where the FIQ code dereferences
invalid/random pointers immediately after being set up, leading to
panic on boot.
The crash occurs as the FIQ code races against hcd_init_fiq() and
the hcd_init_fiq() code races against the outstanding memory stores
from dwc_otg_hcd_init(). Use explicit barriers after touching
driver state.
usb: dwc_otg: fix memory corruption in dwc_otg driver
[Upstream commit
51b1b6491752ac066ee8d32cc66042fcc955fef6]
The move from the staging tree to the main tree exposed a
longstanding memory corruption bug in the dwc2 driver. The
reordering of the driver initialization caused the dwc2 driver
to corrupt the initialization data of the sdhci driver on the
Raspberry Pi platform, which made the bug show up.
The error is in calling to_usb_device(hsotg->dev), since ->dev
is not a member of struct usb_device. The easiest fix is to
just remove the offending code, since it is not really needed.
Thanks to Stephen Warren for tracking down the cause of this.
Reported-by: Andre Heider <a.heider@gmail.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
usb: dwb_otg: Fix unreachable switch statement warning
This warning appears with GCC 7.3.0 from toolchains.bootlin.com:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’:
../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable]
st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps;
~~~~~~~~~~~~~~~~~^~~~
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation
Rationalise the offset and update all call sites.
Fixes https://github.com/raspberrypi/linux/issues/2408
dwc_otg: fix bug with port_addr assignment for single-TT hubs
See https://github.com/raspberrypi/linux/issues/2734
The "Hub Port" field in the split transaction packet was always set
to 1 for single-TT hubs. The majority of single-TT hub products
apparently ignore this field and broadcast to all downstream enabled
ports, which masked the issue. A subset of hub devices apparently
need the port number to be exact or split transactions will fail.
usb: dwc_otg: Clean up build warnings on 64bit kernels
No functional changes. Almost all are changes to logging lines.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
usb: dwc_otg: Use dma allocation for mphi dummy_send buffer
The FIQ driver used a kzalloc'ed buffer for dummy_send,
passing a kernel virtual address to the hardware block.
The buffer is only ever used for a dummy read, so it
should be harmless, but there is the chance that it will
cause exceptions.
Use a dma allocation so that we have a genuine bus address,
and read from that.
Free the allocation when done for good measure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
dwc_otg: only do_split when we actually need to do a split
The previous test would fail if the root port was in fullspeed mode
and there was a hub between the FS device and the root port. While
the transfer worked, the schedule mangling performed for high-speed
split transfers would break leading to an 8ms polling interval.
dwc_otg: fix locking around dequeueing and killing URBs
kill_urbs_in_qh_list() is practically only ever called with the fiq lock
already held, so don't spinlock twice in the case where we need to cancel
an isochronous transfer.
Also fix up a case where the global interrupt register could be read with
the fiq lock not held.
Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907
ARM64/DWC_OTG: Port dwc_otg driver to ARM64
In ARM64, the FIQ mechanism used by this driver is not current
implemented. As a workaround, reqular IRQ is used instead
of FIQ.
In a separate change, the IRQ-CPU mapping is round robined
on ARM64 to increase concurrency and allow multiple interrupts
to be serviced at a time. This reduces the need for FIQ.
Tests Run:
This mechanism is most likely to break when multiple USB devices
are attached at the same time. So the system was tested under
stress.
Devices:
1. USB Speakers playing back a FLAC audio through VLC
at 96KHz.(Higher then typically, but supported on my speakers).
2. sftp transferring large files through the buildin ethernet
connection which is connected through USB.
3. Keyboard and mouse attached and being used.
Although I do occasionally hear some glitches, the music seems to
play quite well.
Signed-off-by: Michael Zoran <mzoran@crowfest.net>
usb: dwc_otg: Clean up interrupt claiming code
The FIQ/IRQ interrupt number identification code is scattered through
the dwc_otg driver. Rationalise it, simplifying the code and solving
an existing issue.
See: https://github.com/raspberrypi/linux/issues/2612
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: Choose appropriate IRQ handover strategy
2711 has no MPHI peripheral, but the ARM Control block can fake
interrupts. Use the size of the DTB "mphi" reg block to determine
which is required.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
usb: host: dwc_otg: fix compiling in separate directory
The dwc_otg Makefile does not respect the O=path argument correctly:
include paths in CFLAGS are given relatively to object path, not source
path. Compiling in a separate directory yields #include errors.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
dwc_otg: use align_buf for small IN control transfers (#3150)
The hardware will do a 4-byte write to memory on any IN packet received
that is between 1 and 3 bytes long. This tramples memory in the uvcvideo
driver, as it uses a sequence of 1- and 2-byte control transfers to
query the min/max/range/step of each individual camera control and
gives us buffers that are offsets into a struct.
Catch small control transfers in the data phase and use the align_buf
to bounce the correct number of bytes into the URB's buffer.
In general, short packets on non-control endpoints should be OK as URBs
should have enough buffer space for a wMaxPacket size transfer.
See: https://github.com/raspberrypi/linux/issues/3148
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: Declare DMA capability with HCD_DMA flag
Following [1], USB controllers have to declare DMA capabilities in
order for them to be used by adding the HCD_DMA flag to their hc_driver
struct.
[1]
7b81cb6bddd2 ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities")
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
dwc_otg: checking the urb->transfer_buffer too early (#3332)
After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't
work well on Pi2/3 boards with 1G physical ram. Users experience
the failure when copying a file of 600M size to the USB stick. And
at the same time, the dmesg shows:
usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg
sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0
When this happens, the sg_buf sent to the driver is located in the
highmem region, the usb_sg_init() in the core/message.c will leave
transfer_buffer to NULL if the sg_buf is in highmem, but in the
dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer
is NULL.
The driver can handle the situation of buffer to be NULL, if it is in
DMA mode, it will convert an address from transfer_dma.
But if the conversion fails or it is in the PIO mode, we should check
buffer and return -EINVAL if it is NULL.
BugLink: https://bugs.launchpad.net/bugs/1852510
Signed-off-by: Hui Wang <hui.wang@canonical.com>
dwc_otg: constrain endpoint max packet and transfer size on split IN
The hcd would unconditionally set the transfer length to the endpoint
packet size for non-isoc IN transfers. If the remaining buffer length
was less than the length of returned data, random memory would get
scribbled over, with bad effects if it crossed a page boundary.
Force a babble error if this happens by limiting the max transfer size
to the available buffer space. DMA will stop writing to memory on a
babble condition.
The hardware expects xfersize to be an integer multiple of maxpacket
size, so override hcchar.b.mps as well.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: pause when cancelling split transactions
Non-periodic splits will DMA to/from the driver-provided transfer_buffer,
which may be freed immediately after the dequeue call returns. Block until
we know the transfer is complete.
A similar delay is needed when cleaning up disconnects, as the FIQ could
have started a periodic transfer in the previous microframe to the one
that triggered a disconnect.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: fiq_fsm: add a barrier on entry into FIQ handler(s)
On BCM2835, there is no hardware guarantee that multiple outstanding
reads to different peripherals will complete in-order. The FIQ code
uses peripheral reads without barriers for performance, so in the case
where a read to a slow peripheral was issued immediately prior to FIQ
entry, the first peripheral read that the FIQ did could end up with
wrong read data returned.
Add dsb(sy) on entry so that all outstanding reads are retired.
The FIQ only issues reads to the dwc_otg core, so per-read barriers
in the handler itself are not required.
On BCM2836 and BCM2837 the barrier is not strictly required due to
differences in how the peripheral bus is implemented, but having
arch-specific handlers that introduce different latencies is risky.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>
dwc_otg: whitelist_table is now productlist_table
dwc_otg: initialise sched_frame for periodic QHs that were parked
If a periodic QH has no remaining QTDs, then it is removed from all
periodic schedules. When re-adding, initialise the sched_frame and
start_split_frame from the current value of the frame counter.
See https://bugs.launchpad.net/raspbian/+bug/1819560
and
https://github.com/raspberrypi/linux/issues/3883
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
dwc_otg: Minimise header and fix build warnings
Delete a large amount of unused declaration from "usb.h", some of which
were causing build warnings, and get the module building cleanly.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc-otg: fix clang -Wignored-attributes warning
warning: attribute declaration must precede definition
dwc-otg: fix clang -Wsometimes-uninitialized warning
warning: variable 'retval' is used uninitialized whenever 'if' condition is false
dwc-otg: fix clang -Wpointer-bool-conversion warning
warning: address of array 'desc->wMaxPacketSize' will always evaluate to 'true'
The wMaxPacketSize field is actually a two element array which content should
be accessed via the UGETW macro.
dwc_otg: fix an undeclared variable
Replace an undeclared variable used by DWC_DEBUGPL with the real endpoint address. DWC_DEBUGPL does nothing with DEBUG undefined so it did not go wrong before.
Signed-off-by: Zixuan Wang <wangzixuan@sjtu.edu.cn>
dwc_otg: Update NetBSD usb.h header licence
NetBSD have changed their licensing requirements such that the 2-clause
licence is preferred. Update usb.h in the downstream dwc_otg code
accordingly.
See https://www.netbsd.org/about/redistribution.html for more
information.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
dwc_otg: pay attention to qh->interval when rescheduling periodic queues
A regression introduced in https://github.com/raspberrypi/linux/pull/3887
meant that if the newly scheduled transfer immediately returned data, and
the driver resubmitted a single URB after every transfer, then the effective
polling interval would end up being approx 1ms.
Use the larger of SCHEDULE_SLOP or the configured endpoint interval.
Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>
drivers: dwc_otg: Fix fallthrough warnings
Signed-off-by: Alexander Winkowski <dereference23@outlook.com>
popcornmix [Sun, 12 May 2013 11:24:19 +0000 (12:24 +0100)]
Main bcm2708/bcm2709 linux port
Signed-off-by: popcornmix <popcornmix@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2709: Drop platform smp and timer init code
irq-bcm2836 handles this through these functions:
bcm2835_init_local_timer_frequency()
bcm2836_arm_irqchip_smp_init()
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm270x: Use watchdog for reboot/poweroff
The watchdog driver already has support for reboot/poweroff.
Make use of this and remove the code from the platform files.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
board_bcm2835: Remove coherent dma pool increase - API has gone
notro [Thu, 10 Jul 2014 11:59:47 +0000 (13:59 +0200)]
pinctrl-bcm2835: Set base to 0 give expected gpio numbering
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
SQUASH: pinctrl: bcm2835: Set base for bcm2711 GPIO to 0
Without this patch GPIOs don't seem to work properly, primarily
noticeable as broken LEDs.
Squash with "pinctrl-bcm2835: Set base to 0 give expected gpio numbering"
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Wed, 29 Jan 2020 09:35:19 +0000 (09:35 +0000)]
tty: amba-pl011: Avoid rare write-when-full error
Under some circumstances on BCM283x processors data loss can be
observed - a single byte missing from the TX output stream. These bytes
are always the last byte of a batch of 8 written from pl011_tx_chars
when from_irq is true, meaning that the FIFO full flag is not checked
before writing.
The transmit optimisation relies on the FIFO being half-empty when the
TX interrupt is raised. Instrumenting the driver further showed that
the failure case correlated with the TX FIFO full flag being set at the
point where the last byte was written to the data register, which
explains the data loss but not how the FIFO appeared to be prematurely
full. A possible explanation is that a FIFO write was in flight at the
time the interrupt was raised, but as yet there is no hypothesis as to
how this might occur.
In the absence of a clear understanding of the failure mechanism, avoid
the problem by checking the FIFO levels before writing the last byte of
the group, which will have minimal performance impact.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 29 Sep 2017 09:32:19 +0000 (10:32 +0100)]
amba_pl011: Add cts-event-workaround DT property
The BCM2835 PL011 implementation seems to have a bug that can lead to a
transmission lockup if CTS changes frequently. A workaround was added to
the driver with a vendor-specific flag to enable it, but this flag is
currently not set for ARM implementations.
Add a "cts-event-workaround" property to Pi DTBs and use the presence
of that property to force the flag to be enabled in the driver.
See: https://github.com/raspberrypi/linux/issues/1280
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 29 Sep 2017 09:32:19 +0000 (10:32 +0100)]
amba_pl011: Insert mb() for correct FIFO handling
The pl011 register accessor functions use the _relaxed versions of the
standard readl() and writel() functions, meaning that there are no
automatic memory barriers. When polling a FIFO status register to check
for fullness, it is necessary to ensure that any outstanding writes have
completed; otherwise the flags are effectively stale, making it possible
that the next write is to a full FIFO.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 17 Oct 2017 14:04:29 +0000 (15:04 +0100)]
lan78xx: Enable LEDs and auto-negotiation
For applications of the LAN78xx that don't have valid programmed
EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default
seems reasonable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Tue, 23 Jan 2018 16:52:45 +0000 (16:52 +0000)]
irqchip: irq-bcm2836: Remove regmap and syscon use
The syscon node defines a register range that duplicates that used by
the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are
built in and always present together (both drivers are enabled by
CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a
global variable that simplifies the code. Doing so does lose the
locking provided by regmap, but as only one side is using the regmap
interface (irq-bcm2835 uses readl and write) there is no loss of
atomicity.
See: https://github.com/raspberrypi/firmware/issues/926
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Noralf Trønnes [Tue, 1 Nov 2016 14:15:41 +0000 (15:15 +0100)]
i2c: bcm2835: Add debug support
This adds a debug module parameter to aid in debugging transfer issues
by printing info to the kernel log. When enabled, status values are
collected in the interrupt routine and msg info in
bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid
affecting timing. Having printk in the isr can mask issues.
debug values (additive):
1: Print info on error
2: Print info on all transfers
3: Print messages before transfer is started
The value can be changed at runtime:
/sys/module/i2c_bcm2835/parameters/debug
Example output, debug=3:
[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1]
[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1]
[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1]
[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1]
[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1]
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Claggy3 [Sat, 11 Feb 2017 14:00:30 +0000 (14:00 +0000)]
Update vfpmodule.c
Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m.
This patch fixes a problem with VFP state save and restore related
to exception handling (panic with message "BUG: unsupported FP
instruction in kernel mode") present on VFP11 floating point units
(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry
Pi boards). This patch was developed and discussed on
https://github.com/raspberrypi/linux/issues/859
A precondition to see the crashes is that floating point exception
traps are enabled. In this case, the VFP11 might determine that a FPU
operation needs to trap at a point in time when it is not possible to
signal this to the ARM11 core any more. The VFP11 will then set the
FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases,
a second opcode might have been accepted by the VFP11 before the
exception was detected and could be reported to the ARM11 - in this
case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in
FPINST2.)
If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued
by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode
trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits
to decide what actions to take, i.e., whether to emulate the opcodes
found in FPINST and FPINST2, and whether to retry the bounced instruction.
If a user space application has left the VFP11 in this "pending trap"
state, the next FPU opcode issued to the VFP11 might actually be the
VSTMIA operation vfp_save_state() uses to store the FPU registers
to memory (in our test cases, when building the signal stack frame).
In this case, the kernel crashes as described above.
This patch fixes the problem by making sure that vfp_save_state() is
always entered with FPEXC.EX cleared. (The current value of FPEXC has
already been saved, so this does not corrupt the context. Clearing
FPEXC.EX has no effects on FPINST or FPINST2. Also note that many
callers already modify FPEXC by setting FPEXC.EN before invoking
vfp_save_state().)
This patch also addresses a second problem related to FPEXC.EX: After
returning from signal handling, the kernel reloads the VFP context
from the user mode stack. However, the current code explicitly clears
both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these
bits to be preserved, this patch disables clearing them for VFP
implementations belonging to architecture 1. There should be no
negative side effects: the user can set both bits by executing FPU
opcodes anyway, and while user code may now place arbitrary values
into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support
code knows which instructions can be emulated, and rejects other
opcodes with "unhandled bounce" messages, so there should be no
security impact from allowing reloading FPEXC.EX and FPEXC.FP2V.
Signed-off-by: Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net>
Phil Elwell [Thu, 9 Feb 2017 14:36:44 +0000 (14:36 +0000)]
sound: Demote deferral errors to INFO level
At present there is no mechanism to specify driver load order,
which can lead to deferrals and repeated retries until successful.
Since this situation is expected, reduce the dmesg level to
INFO and mention that the operation will be retried.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Tue, 6 Dec 2016 17:05:39 +0000 (17:05 +0000)]
bcm2835-rng: Avoid initialising if already enabled
Avoids the 0x40000 cycles of warmup again if firmware has already used it
popcornmix [Wed, 9 Nov 2016 13:02:52 +0000 (13:02 +0000)]
bcm: Make RASPBERRYPI_POWER depend on PM
popcornmix [Tue, 5 Apr 2016 18:40:12 +0000 (19:40 +0100)]
reboot: Use power off rather than busy spinning when halt is requested
reboot: Use power off rather than busy spinning when halt is requested
Busy spinning after halt is dumb
We've previously applied this patch to arch/arm
but it is currenltly missing in arch/arm64
Pi4 after "sudo halt" uses 520mA
Pi4 after "sudo shutdown now" uses 310mA
Make them both use the lower powered option
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Noralf Trønnes [Fri, 7 Oct 2016 14:50:59 +0000 (16:50 +0200)]
watchdog: bcm2835: Support setting reboot partition
The Raspberry Pi firmware looks at the RSTS register to know which
partition to boot from. The reboot syscall command
LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument.
Add support for passing in a partition number 0..63 to boot from.
Partition 63 is a special partiton indicating halt.
If the partition doesn't exist, the firmware falls back to partition 0.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Phil Elwell [Wed, 15 Jun 2016 15:48:41 +0000 (16:48 +0100)]
rtc: Add SPI alias for pcf2123 driver
Without this alias, Device Tree won't cause the driver
to be loaded.
See: https://github.com/raspberrypi/linux/pull/1510
Noralf Trønnes [Sat, 3 Oct 2015 20:22:55 +0000 (22:22 +0200)]
dmaengine: bcm2835: Load driver early and support legacy API
Load driver early since at least bcm2708_fb doesn't support deferred
probing and even if it did, we don't want the video driver deferred.
Support the legacy DMA API which is needed by bcm2708_fb.
Don't mask out channel 2.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
bcm2835-dma: Add support for per-channel flags
Add the ability to interpret the high bits of the dreq specifier as
flags to be included in the DMA_CS register. The motivation for this
change is the ability to set the DISDEBUG flag for SD card transfers
to avoid corruption when using the VPU debugger.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-dma: Add proper 40-bit DMA support
BCM2711 has 4 DMA channels with a 40-bit address range, allowing them
to access the full 4GB of memory on a Pi 4.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
bcm2835-dma: Derive slave DMA addresses correctly
Slave addresses for DMA are meant to be supplied as physical addresses
(contrary to what struct snd_dmaengine_dai_dma_data does). It is up to
the DMA controller driver to perform the translation based on its own
view of the world, as described in Device Tree.
Now that the Pi Device Trees have the correct peripheral mappings,
replace the hacky address munging with phys_to_dma().
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-dma: Add NO_WAIT_RESP flag
Use bit 27 of the dreq value (the second cell of the DT DMA descriptor)
to request that the WAIT_RESP bit is not set.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-dma: Advertise the full DMA range
Unless the DMA mask is set wider than 32 bits, DMA mapping will use a
bounce buffer.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
bcm2835-dma: only reserve channel 0 if legacy dma driver is enabled
If CONFIG_DMA_BCM2708 isn't enabled there's no need to mask out
one of the already scarce DMA channels.
Signed-off-by: Matthias Reichl <hias@horus.com>
bcm2835-dma: Avoid losing CS flags after interrupt
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Add bcm2835-dma: Add DMA_WIDE_SOURCE and DMA_WIDE_DEST flags
Use (reserved) bits 24 and 25 of the dreq value
(the second cell of the DT DMA descriptor) to request
that wide source reads or wide dest writes are required
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
dmaengine: bcm2835: Fix position reporting for 40 bits channels
For 40 bits channels, the position is reported by reading the upper byte
in the SRCI/DESTI registers. However the driver adds that upper byte
with an 8-bits left shift, while it should be 32.
Fixes:
9a52a9918306 ("bcm2835-dma: Add proper 40-bit DMA support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
dmaengine: bcm2835: Use to_bcm2711_cbaddr where relevant
bcm2711_dma40_memcpy has some code strictly equivalent to the
to_bcm2711_cbaddr() function. Let's use it instead.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
dmaengine: bcm2835: Fix descriptors usage for 40-bits channels
The bcm2835_dma_create_cb_chain() function is in charge of building up
the descriptors chain for a given transfer.
It was initially supporting only the BCM2835-style DMA controller, and
was later expanded to support controllers with 40-bits channels that use
a different descriptor layout.
However, some part of the function only use the old style descriptor,
even when building a chain of new-style descriptors, resulting in weird
bugs.
Fixes:
9a52a9918306 ("bcm2835-dma: Add proper 40-bit DMA support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
bcm2835-dma: Fix WAIT_RESP on memcpy
It goes in info not extra
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Fix dma_abort for 40-bit channels
It wasn't aborting the transfer and caused stop/start
of hdmi audio dma to be unreliable.
New sequence approved by Broadcom.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Fix dma_abort for non-40bit channels
The sequence we were doing was not safe.
Clearing CS meant BCM2835_DMA_WAIT_FOR_WRITES was cleared
and so polling BCM2835_DMA_WAITING_FOR_WRITES has no benefit
Broadcom have provided a recommended sequence to abort
a dma lite channel, so switch to that.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Support dma flags for multi-beat burst
Add a control bit to enable a multi-beat burst on a DMA.
This improves DMA performance and is required for HDMI audio.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
bcm2835-dma: Need to keep PROT bits set in CS on 40bit controller
Resetting them to zero puts DMA channel into secure mode
which makes further accesses impossible
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Mon, 24 Jan 2022 13:41:16 +0000 (13:41 +0000)]
spi: spidev: Completely disable the spidev warning
An alternative strategy would be to use "rpi,spidev" instead, but that
would require many Raspberry Pi Device Tree changes.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Noralf Trønnes [Fri, 23 Oct 2015 14:26:55 +0000 (16:26 +0200)]
irqchip: irq-bcm2835: Add 2836 FIQ support
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Noralf Trønnes [Fri, 12 Jun 2015 17:01:05 +0000 (19:01 +0200)]
irqchip: bcm2835: Add FIQ support
Add a duplicate irq range with an offset on the hwirq's so the
driver can detect that enable_fiq() is used.
Tested with downstream dwc_otg USB controller driver.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Phil Elwell [Thu, 9 Feb 2017 14:33:30 +0000 (14:33 +0000)]
irq-bcm2836: Avoid "Invalid trigger warning"
Initialise the level for each IRQ to avoid a warning from the
arm arch timer code.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Fri, 13 Mar 2015 12:43:36 +0000 (12:43 +0000)]
Protect __release_resource against resources without parents
Without this patch, removing a device tree overlay can crash here.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 27 Nov 2017 17:14:54 +0000 (17:14 +0000)]
cgroup: Disable cgroup "memory" by default
Some Raspberry Pis have limited RAM and most users won't use the
cgroup memory support so it is disabled by default. Enable with:
cgroup_enable=memory
See: https://github.com/raspberrypi/linux/issues/1950
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
popcornmix [Tue, 26 Mar 2013 17:26:38 +0000 (17:26 +0000)]
Allow mac address to be set in smsc95xx
Signed-off-by: popcornmix <popcornmix@gmail.com>
SQUASH: smsc95xx: Use dev_mod_addr to set MAC addr
Since
adeef3e32146 ("net: constify netdev->dev_addr") it has been
illegal to write to the dev_addr MAC address field. Later commits
have added explicit checks that it hasn't been modified by nefarious
means. The dev_addr_mod helper function is the accepted way to change
the dev_addr field, so use it.
Squash with
96c1def63ee1 ("Allow mac address to be set in smsc95xx").
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Sam Nazarko [Fri, 1 Apr 2016 16:27:21 +0000 (17:27 +0100)]
smsc95xx: Experimental: Enable turbo_mode and packetsize=2560 by default
See: http://forum.kodi.tv/showthread.php?tid=285288
Steve Glendinning [Thu, 19 Feb 2015 18:47:12 +0000 (18:47 +0000)]
smsx95xx: fix crimes against truesize
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings.
This patch stops smsc95xx from changing truesize.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Dom Cobley [Mon, 31 Jul 2023 12:47:10 +0000 (13:47 +0100)]
Revert "Revert "xhci: add quirk for host controllers that don't update endpoint DCS""
This reverts commit
5bef4b3cb95a5b883dfec8b3ffc0d671323d55bb.
We don't agree with upstream revert so undo it.
Phil Elwell [Mon, 7 Mar 2022 16:18:55 +0000 (16:18 +0000)]
Revert "net: bcmgenet: Request APD, DLL disable and IDDQ-SR"
This reverts commit
c3a4c69360ab43560f212eed326c9d8bde35b14c, which
broke rebooting when network booting.
See: https://github.com/raspberrypi/rpi-eeprom/issues/417
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 1 Mar 2021 09:14:35 +0000 (09:14 +0000)]
Revert "Bluetooth: Always request for user confirmation for Just Works"
This reverts commit
92516cd97fd4d8ad5b1421a0d51771044f453a5f.
Thi commit "Bluetooth: Always request for user confirmation for Just
Works" prevents BLE devices pairing in (at least) the Raspberry Pi OS
GUI. After reverting it, pairing works again.
If another solution to the problem is found then this reversion will
be removed.
See: https://github.com/raspberrypi/linux/issues/4139
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 1 Mar 2021 09:12:44 +0000 (09:12 +0000)]
Revert "Bluetooth: Always request for user confirmation for Just Works (LE SC)"
This reverts commit
ffee202a78c2980688bc5d2f7d56480e69a5e0c9.
The commit "Bluetooth: Always request for user confirmation for Just
Works" prevents BLE devices pairing in (at least) the Raspberry Pi OS
GUI. After reverting it, pairing works again. Although this companion
commit ("... (LE SC)") has not been demonstrated to be problematic,
it follows the same logic and therefore could affect some use cases.
If another solution to the problem is found then this reversion will
be removed.
See: https://github.com/raspberrypi/linux/issues/4139
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Phil Elwell [Mon, 20 Apr 2020 12:41:10 +0000 (13:41 +0100)]
Revert "spi: spidev: Fix CS polarity if GPIO descriptors are used"
This reverts commit
83b2a8fe43bda0c11981ad6afa5dd0104d78be28.
popcornmix [Fri, 25 Aug 2017 18:18:13 +0000 (19:18 +0100)]
cache: export clean and invalidate
hack: cache: Fix linker error
Dan Pasanen [Thu, 21 Sep 2017 14:55:42 +0000 (09:55 -0500)]
arm: partially revert
702b94bff3c50542a6e4ab9a4f4cef093262fe65
* Re-expose some dmi APIs for use in VCSM
Dom Cobley [Tue, 19 Oct 2021 13:14:55 +0000 (14:14 +0100)]
clk-bcm2835: Remove VEC clock support
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Phil Elwell [Thu, 8 Jul 2021 08:37:10 +0000 (09:37 +0100)]
clk: bcm2835: Pass DT node to rpi_firmware_get
The fw_node pointer has already been retrieved, and using it allows
us to remove a downstream patch to the firmware driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
popcornmix [Tue, 3 Sep 2019 19:28:00 +0000 (20:28 +0100)]
clk-bcm2835: Disable v3d clock
This is controlled by firmware, see clk-raspberrypi.c
Signed-off-by: popcornmix <popcornmix@gmail.com>
popcornmix [Tue, 6 Aug 2019 14:23:14 +0000 (15:23 +0100)]
clk-bcm2835: Avoid null pointer exception
clk_desc_array[BCM2835_PLLB] doesn't exist so we dereference null when iterating
Signed-off-by: popcornmix <popcornmix@gmail.com>
Eric Anholt [Thu, 2 May 2019 22:24:04 +0000 (15:24 -0700)]
clk: bcm2835: Allow reparenting leaf clocks while they're running.
This falls under the same "we can reprogram glitch-free as long as we
pause generation" rule as updating the div/frac fields. This can be
used for runtime reclocking of V3D to manage power leakage.
Signed-off-by: Eric Anholt <eric@anholt.net>
Eric Anholt [Thu, 2 May 2019 22:11:05 +0000 (15:11 -0700)]
clk: bcm2835: Add support for setting leaf clock rates while running.
As long as you wait for !BUSY, you can do glitch-free updates of clock
rate while the clock is running.
Signed-off-by: Eric Anholt <eric@anholt.net>
Phil Elwell [Wed, 23 Jan 2019 16:11:50 +0000 (16:11 +0000)]
clk-bcm2835: Don't wait for pllh lock
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Dave Stevenson [Thu, 24 Jan 2019 15:09:28 +0000 (15:09 +0000)]
clk: clk-bcm2835: Use %zd when printing size_t
The debug text for how many clocks have been registered
uses "%d" with a size_t. Correct it to "%zd".
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Phil Elwell [Mon, 6 Mar 2017 09:06:18 +0000 (09:06 +0000)]
clk-bcm2835: Read max core clock from firmware
The VPU is responsible for managing the core clock, usually under
direction from the bcm2835-cpufreq driver but not via the clk-bcm2835
driver. Since the core frequency can change without warning, it is
safer to report the maximum clock rate to users of the core clock -
I2C, SPI and the mini UART - to err on the safe side when calculating
clock divisors.
If the DT node for the clock driver includes a reference to the
firmware node, use the firmware API to query the maximum core clock
instead of reading the divider registers.
Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about
160KHz. In particular, switching to the 4.9 kernel was likely to break
SenseHAT usage on a Pi3.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 13 Feb 2017 17:20:08 +0000 (17:20 +0000)]
clk-bcm2835: Add claim-clocks property
The claim-clocks property can be used to prevent PLLs and dividers
from being marked as critical. It contains a vector of clock IDs,
as defined by dt-bindings/clock/bcm2835.h.
Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and
PLLH_PIX for the vc4_kms_v3d driver.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Phil Elwell [Mon, 13 Feb 2017 17:20:08 +0000 (17:20 +0000)]
clk-bcm2835: Mark used PLLs and dividers CRITICAL
The VPU configures and relies on several PLLs and dividers. Mark all
enabled dividers and their PLLs as CRITICAL to prevent the kernel from
switching them off.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Martin Sperl [Fri, 2 Sep 2016 15:45:27 +0000 (16:45 +0100)]
Register the clocks early during the boot process, so that special/critical clocks can get enabled early on in the boot process avoiding the risk of disabling a clock, pll_divider or pll when a claiming driver fails to install propperly - maybe it needs to defer.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Dom Cobley [Tue, 12 Apr 2022 19:07:20 +0000 (20:07 +0100)]
clk-raspberrypi: Add ISP to exported clocks
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
popcornmix [Mon, 13 Apr 2015 16:16:29 +0000 (17:16 +0100)]
config: Add default configs
notro [Wed, 9 Jul 2014 12:46:08 +0000 (14:46 +0200)]
BCM2708: Add core Device Tree support
Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since
2aefcd576195a739a7a256099571c9c4a401005f,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: DT build rules no longer arch-specific
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Maxime Ripard [Mon, 6 Jun 2022 09:02:16 +0000 (11:02 +0200)]
arm64: setup: Fix build warning
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Mon, 24 Apr 2023 17:32:45 +0000 (18:32 +0100)]
drm/vc4: Limit max_bpc to 8 on Pi0-3
Pi 0-3 have no deep colour support and only 24bpp output,
so max_bpc should remain as 8.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Matthias Reichl [Sat, 11 Mar 2023 21:41:17 +0000 (22:41 +0100)]
drm/vc4: drop unnecessary and harmful HDMI RGB format check
RGB is a mandatory format for all DVI and HDMI monitors so there's
no need to check for presence of the DRM_COLOR_FORMAT_RGB444 bit in
color_formats.
More importantly this checks breaks working around EDID issues with
eg video=HDMI-A-1:1024x768D or drm.edid_firmware=edid/1024x768.bin
as the RGB444 bit is only set when a valid EDID with digital bit set in
the input byte is present - which isn't the case when no EDID can be
read from the display device at all or with the in-built kernel EDIDs,
which mimic analog (VGA) displays without the digital bit set.
So drop the check, if we output video on the HDMI connector we can
assume that the display can accept 8bit RGB.
Signed-off-by: Matthias Reichl <hias@horus.com>
Dave Stevenson [Thu, 11 Aug 2022 12:59:34 +0000 (13:59 +0100)]
drm/vc4: Set AXI panic modes for the HVS
The HVS can change AXI request mode based on how full the COB
FIFOs are.
Until now the vc4 driver has been relying on the firmware to
have set these to sensible values.
With HVS channel 2 now being used for live video, change the
panic mode for all channels to be explicitly set by the driver,
and the same for all channels.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Matthias Reichl [Sat, 14 Jan 2023 15:24:39 +0000 (16:24 +0100)]
drm/vc4: Calculate bpc based on max_requested_bpc
This aligns vc4 with Intel, AMD and Synopsis drivers and fixes max bpc
connector property not working as expected on monitors with YCbCr 4:2:2
support but not deep color support.
max_bpc in connector state is clamped at max_bpc from display info and
the latter only takes deep color modes into account so it will always
be 8, even if the display can do 4:2:2 12-bit output.
Signed-off-by: Matthias Reichl <hias@horus.com>
Dom Cobley [Tue, 31 Jan 2023 15:14:32 +0000 (15:14 +0000)]
drm/vc4_plane: Add support for YUV444 formats
Support displaying DRM_FORMAT_YUV444 and DRM_FORMAT_YVU444 formats.
Tested with kmstest and kodi. e.g.
kmstest -r 1920x1080@60 -f 400x300-YU24
Note: without the shift of width, only half the chroma is fetched,
resulting in correct left half of image and corrupt colours on right half.
The increase in width shouldn't affect fetching of Y data,
as the hardware will clamp at dest width.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Maxime Ripard [Wed, 25 Jan 2023 12:05:26 +0000 (13:05 +0100)]
drm/vc4: hvs: Destroy dlist allocations immediately when running a test
When running a kunit test, the driver runs with a mock device. As such,
any attempt to read or write to a hardware register will fail the
current test immediately.
The dlist allocation management recently introduced will read the
current frame count from the HVS to defer its destruction until a
subsequent frame has been output. This obviously involves a register
read that fails the Kunit tests.
Change the destruction deferral function to destroy the allocation
immediately if we run under kunit. This is essentially harmless since
the main reason for that deferall is to prevent any access to the
hardware dlist while a frame described by that list is rendered. On our
mock driver, we have neither a hardware dlist nor a rendering, so it
doesn't matter.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Wed, 25 Jan 2023 11:54:36 +0000 (12:54 +0100)]
drm/vc4: hvs: Move the dlist allocation destruction to a function
We'll need to destroy a dlist allocation in multiple code paths, so
let's move it to a separate function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Wed, 25 Jan 2023 11:38:37 +0000 (12:38 +0100)]
drm/vc4: hvs: Initialize the dlist allocation list entry
The vc4_hvs_dlist_allocation structure has a list that we don't
initialize when we allocate a new instance.
This makes any call reading the list structure (such as list_empty) fail
with a NULL pointer dereference.
Let's make sure our list is always initialized.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Maxime Ripard [Thu, 16 Dec 2021 13:54:54 +0000 (14:54 +0100)]
drm/vc4: hvs: Defer dlist slots deallocation
During normal operations, the cursor position update is done through an
asynchronous plane update, which on the vc4 driver basically just
modifies the right dlist word to move the plane to the new coordinates.
However, when we have the overscan margins setup, we fall back to a
regular commit when we are next to the edges. And since that commit
happens to be on a cursor plane, it's considered a legacy cursor update
by KMS.
The main difference it makes is that it won't wait for its completion
(ie, next vblank) before returning. This means if we have multiple
commits happening in rapid succession, we can have several of them
happening before the next vblank.
In parallel, our dlist allocation is tied to a CRTC state, and each time
we do a commit we end up with a new CRTC state, with the previous one
being freed. This means that we free our previous dlist entry (but don't
clear it though) every time a new one is being committed.
Now, if we were to have two commits happening before the next vblank, we
could end up freeing reusing the same dlist entries before the next
vblank.
Indeed, we would start from an initial state taking, for example, the
dlist entries 10 to 20, then start a commit taking the entries 20 to 30
and setting the dlist pointer to 20, and freeing the dlist entries 10 to
20. However, since we haven't reach vblank yet, the HVS is still using
the entries 10 to 20.
If we were to make a new commit now, chances are the allocator are going
to give the 10 to 20 entries back, and we would change their content to
match the new state. If vblank hasn't happened yet, we just corrupted
the active dlist entries.
A first attempt to solve this was made by creating an intermediate dlist
buffer to store the current (ie, as of the last commit) dlist content,
that we would update each time the HVS is done with a frame. However, if
the interrupt handler missed the vblank window, we would end up copying
our intermediate dlist to the hardware one during the composition,
essentially creating the same issue.
Since making sure that our interrupt handler runs within a fixed,
constrained, time window would require to make Linux a real-time kernel,
this seems a bit out of scope.
Instead, we can work around our original issue by keeping the dlist
slots allocation longer. That way, we won't reuse a dlist slot while
it's still in flight. In order to achieve this, instead of freeing the
dlist slot when its associated CRTC state is destroyed, we'll queue it
in a list.
A naive implementation would free the buffers in that queue when we get
our end of frame interrupt. However, there's still a race since, just
like in the shadow dlist case, we don't control when the handler for
that interrupt is going to run. Thus, we can end up with a commit adding
an old dlist allocation to our queue during the window between our
actual interrupt and when our handler will run. And since that buffer is
still being used for the composition of the current frame, we can't free
it right away, exposing us to the original bug.
Fortunately for us, the hardware provides a frame counter that is
increased each time the first line of a frame is being generated.
Associating the frame counter the image is supposed to go away to the
allocation, and then only deallocate buffers that have a counter below
or equal to the one we see when the deallocation code should prevent the
above race from occuring.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dom Cobley [Tue, 6 Dec 2022 15:05:56 +0000 (15:05 +0000)]
vc4_hdmi: Avoid log spam for audio start failure
We regularly get dmesg error reports of:
[ 18.184066] hdmi-audio-codec hdmi-audio-codec.3.auto: ASoC: error at snd_soc_dai_startup on i2s-hifi: -19
[ 18.184098] MAI: soc_pcm_open() failed (-19)
Currently I get 30 of these when booting to desktop.
We always say, ignore they are harmless, but removing them would be good.
A bit of investigation shows, for me, the errors are all generated by second, unused hdmi interface.
It shows as an alsa device, and pulseaudio attempts to open it (numerous times), generating a kernel
error message each time.
systemctl --user restart pulseaudio.service generates 6 additional error messages.
The error messages all come through:
https://github.com/raspberrypi/linux/blob/
a009a9c0d79dfec114ee5102ec3d3325a172c952/sound/soc/soc-pcm.c#L39
which suggests returning ENOTSUPP, rather that ENODEV will be quiet. And indeed it is.
Note: earlier kernels do not have the quiet ENOTSUPP, so additional cherry-picks will be needed to backport
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Wed, 1 Jun 2022 14:43:51 +0000 (15:43 +0100)]
drm/vc4_hdmi: Allow hotplug detect to be forced
See: https://forum.libreelec.tv/thread/24783-tv-avr-turns-back-on-right-after-turning-them-off
While the kernel provides a :D flag for assuming device is connected,
it doesn't stop this function from being called and generating a cec_phys_addr_invalidate
message when hotplug is deasserted.
That message provokes a flurry of CEC messages which for many users results in the TV
switching back on again and it's very hard to get it to stay switched off.
It seems to only occur with an AVR and TV connected but has been observed across a
number of manufacturers.
The issue started with https://github.com/raspberrypi/linux/pull/4371
and this provides an optional way of getting back the old behaviour
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Maxime Ripard [Mon, 11 Jul 2022 08:38:25 +0000 (10:38 +0200)]
drm/vc4: hvs: Skip DebugFS Registration for FKMS
FKMS doesn't have an HVS and it's expected. Return from the debugfs init
function immediately if we're running with fkms.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Fri, 1 Apr 2022 16:10:37 +0000 (17:10 +0100)]
drm/atomic: If margins are updated, update all planes.
Margins may be implemented by scaling the planes, but as there
is no way of intercepting the set_property for a standard property,
and all planes are checked in drm_atomic_check_only before the
connectors, there's now way to add the planes into the state
from the driver.
If the margin properties change, add all corresponding planes to
the state.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Daniel Vetter [Fri, 23 Oct 2020 12:39:23 +0000 (14:39 +0200)]
drm/atomic-helpers: remove legacy_cursor_update hacks
The stuff never really worked, and leads to lots of fun because it
out-of-order frees atomic states. Which upsets KASAN, among other
things.
For async updates we now have a more solid solution with the
->atomic_async_check and ->atomic_async_commit hooks. Support for that
for msm and vc4 landed. nouveau and i915 have their own commit
routines, doing something similar.
For everyone else it's probably better to remove the use-after-free
bug, and encourage folks to use the async support instead. The
affected drivers which register a legacy cursor plane and don't either
use the new async stuff or their own commit routine are: amdgpu,
atmel, mediatek, qxl, rockchip, sti, sun4i, tegra, virtio, and vmwgfx.
Inspired by an amdgpu bug report.
v2: Drop RFC, I think with amdgpu converted over to use
atomic_async_check/commit done in
commit
674e78acae0dfb4beb56132e41cbae5b60f7d662
Author: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Date: Wed Dec 5 14:59:07 2018 -0500
drm/amd/display: Add fast path for cursor plane updates
we don't have any driver anymore where we have userspace expecting
solid legacy cursor support _and_ they are using the atomic helpers in
their fully glory. So we can retire this.
v3: Paper over msm and i915 regression. The complete_all is the only
thing missing afaict.
v4: Rebased on recent kernel, added extra link for vc4 bug.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199425
Link: https://lore.kernel.org/all/20220221134155.125447-9-maxime@cerno.tech/
Cc: mikita.lipski@amd.com
Cc: Michel Dänzer <michel@daenzer.net>
Cc: harry.wentland@amd.com
Cc: Rob Clark <robdclark@gmail.com>
Cc: "Kazlauskas, Nicholas" <nicholas.kazlauskas@amd.com>
Tested-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Fri, 1 Apr 2022 10:31:38 +0000 (11:31 +0100)]
drm/vc4: Force trigger of dlist update on margins change
When the margins are changed, the dlist needs to be regenerated
with the changed updated dest regions for each of the planes.
Setting the zpos_changed flag is sufficient to trigger that
without doing a full modeset, therefore set it should the
margins be changed.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dom Cobley [Thu, 27 Jan 2022 15:32:04 +0000 (15:32 +0000)]
vc4/drm:plane: Make use of chroma siting parameter
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Wed, 26 Jan 2022 15:58:13 +0000 (15:58 +0000)]
drm: Add chroma siting properties
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Fri, 9 Apr 2021 14:00:40 +0000 (15:00 +0100)]
vc4/drm: Handle fractional coordinates using the phase field
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dom Cobley [Mon, 14 Mar 2022 17:56:10 +0000 (17:56 +0000)]
vc4/drm: vc4_plane: Keep fractional source coords inside state
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Dave Stevenson [Thu, 20 Jan 2022 17:29:36 +0000 (17:29 +0000)]
drm/bridge: tc358762: Ignore EPROBE_DEFER when logging errors
mipi_dsi_attach can fail due to resources not being available
yet, therefore do not log error messages should they occur.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Fri, 17 Dec 2021 13:36:52 +0000 (13:36 +0000)]
drm/dsi: Document the meaning and spec references for MIPI_DSI_MODE_*
The MIPI_DSI_MODE_* flags have fairly terse descriptions and no reference
to the DSI specification as to their exact meaning. Usage has therefore
been rather fluid.
Extend the descriptions and provide references to the part of the
MIPI DSI specification regarding what they mean.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Thu, 13 Jan 2022 11:30:42 +0000 (11:30 +0000)]
drm/vc4: Disable Gamma control on HVS5 due to issues writing the table
Still under investigation, but the conditions under which the HVS
will accept values written to the gamma PWL are not straightforward.
Disable gamma on HVS5 again until it can be resolved to avoid
gamma being enabled with an incorrect table.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Wed, 10 Nov 2021 16:36:12 +0000 (16:36 +0000)]
drm/vc4: Validate the size of the gamma_lut
Add a check to vc4_hvs_gamma_check to ensure a new non-empty
gamma LUT is of the correct length before accepting it.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Mon, 8 Nov 2021 18:25:49 +0000 (18:25 +0000)]
drm/vc4: Only add gamma properties once.
Two calls were made to drm_crtc_enable_color_mgmt to add gamma
and CTM, however they were both set to add the gamma properties,
so they ended up added twice.
Fixes:
766cc6b1f7fc "drm/vc4: Add CTM support"
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Mon, 8 Nov 2021 17:32:45 +0000 (17:32 +0000)]
drm/vc4: Enable gamma block only when required.
With HVS5 the gamma block is now only reprogrammed with
a disable/enable. Loading the table from vc4_hvs_init_channel
(called from vc4_hvs_atomic_enable) appears to be at an
invalid point in time and so isn't applied.
Switch to enabling and disabling the gamma table instead. This
isn't safe if the pipeline is running, but it isn't now.
For HVS4 it is safe to enable and disable dynamically, so
adopt that approach there too.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 2 Nov 2021 16:01:36 +0000 (16:01 +0000)]
drm: Check whether the gamma lut has changed before updating
drm_crtc_legacy_gamma_set updates the gamma_lut blob unconditionally,
which leads to unnecessary reprogramming of hardware.
Check whether the blob contents has actually changed before
signalling that it has been updated.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Mateusz Kwiatkowski [Wed, 14 Jul 2021 23:08:11 +0000 (01:08 +0200)]
drm/vc4: Make VEC progressive modes readily accessible
Add predefined modelines for the 240p (NTSC) and 288p (PAL) progressive
modes, and report them through vc4_vec_connector_get_modes().
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Mateusz Kwiatkowski [Wed, 14 Jul 2021 23:08:08 +0000 (01:08 +0200)]
drm/vc4: Relax VEC modeline requirements and add progressive mode support
Make vc4_vec_encoder_atomic_check() accept arbitrary modelines, as long
as they result in somewhat sane output from the VEC. The bounds have
been determined empirically. Additionally, add support for the
progressive 262-line and 312-line modes.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Maxime Ripard [Mon, 14 Jun 2021 13:28:30 +0000 (15:28 +0200)]
drm/vc4: hvs: Force modeset on gamma lut change
The HVS Gamma block can only be updated when idle, so we need to disable
the HVS channel when the gamma property is set in an atomic commit.
Since the pixelvalve cannot have its assigned channel halted without
stalling unless it's disabled as well, in our case that means forcing a
full disable / enable cycle on the pipeline.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Wed, 28 Apr 2021 10:32:10 +0000 (12:32 +0200)]
drm/vc4: Add debugfs node that dumps the vc5 gamma PWL entries
This helps with debugging the conversion from a 256 point gamma LUT to
16 point PWL entries as used by the BCM2711.
Co-developed-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Tue, 27 Apr 2021 12:24:21 +0000 (14:24 +0200)]
drm/vc4: Add support for gamma on BCM2711
BCM2711 changes from a 256 entry lookup table to a 16 point
piecewise linear function as the pipeline bitdepth has increased
to make a LUT unwieldy.
Implement a simple conversion from a 256 entry LUT that userspace
is likely to expect to 16 evenly spread points in the PWL. This
could be improved with curve fitting at a later date.
Co-developed-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Dave Stevenson [Mon, 7 Sep 2020 16:32:27 +0000 (17:32 +0100)]
drm/vc4: Add firmware-kms mode
This is a squash of all firmware-kms related patches from previous
branches, up to and including
"drm/vc4: Set the possible crtcs mask correctly for planes with FKMS"
plus a couple of minor fixups for the 5.9 branch.
Please refer to earlier branches for full history.
This patch includes work by Eric Anholt, James Hughes, Phil Elwell,
Dave Stevenson, Dom Cobley, and Jonathon Bell.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup firmware-kms after "drm/atomic: Pass the full state to CRTC atomic enable/disable"
Prototype for those calls changed, so amend fkms (which isn't
upstream) to match.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Fixup fkms for API change
Atomic flush and check changed API, so fix up the downstream-only
FKMS driver.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: Make normalize_zpos conditional on using fkms
Eric's view was that there was no point in having zpos
support on vc4 as all the planes had the same functionality.
Can be later squashed into (and fixes):
drm/vc4: Add firmware-kms mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/vc4: FKMS: Change of Broadcast RGB mode needs a mode change
The Broadcast RGB (aka HDMI limited/full range) property is only
notified to the firmware on mode change, so this needs to be
signalled when set.
https://github.com/raspberrypi/firmware/issues/1580
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
vc4/drv: Only notify firmware of display done with kms
fkms driver still wants firmware display to be active
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
ydrm/vc4: fkms: Fix margin calculations for the right/bottom edges
The calculations clipped the right/bottom edge of the clipped
range based on the left/top margins.
https://github.com/raspberrypi/linux/issues/4447
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
drm/vc4: fkms: Use new devm_rpi_firmware_get api
drm/kms: Add allow_fb_modifiers
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
drm/vc4: Add async update support for cursor planes
Now that cursors are implemented as regular planes, all cursor
movements result in atomic updates. As the firmware-kms driver
doesn't support asynchronous updates, these are synchronous, which
limits the update rate to the screen refresh rate. Xorg seems unaware
of this (or at least of the effect of this), because if the mouse is
configured with a higher update rate than the screen then continuous
mouse movement results in an increasing backlog of mouse events -
cue extreme lag.
Add minimal support for asynchronous updates - limited to cursor
planes - to eliminate the lag.
See: https://github.com/raspberrypi/linux/pull/4971
https://github.com/raspberrypi/linux/issues/4988
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
drivers/gpu/drm/vc4: Add missing 32-bit RGB formats
The missing 32-bit per pixel ABGR and various "RGB with an X value"
formats are added. Change sent by Dave Stevenson.
Signed-off-by: David Plowman <david.plowman@raspberrypi.com>
drm: vc4: Fixup duplicated macro definition in vc4_firmware_kms
Both vc4_drv.h and vc4_firmware_kms.c had definitions for
to_vc4_crtc.
Rename the fkms one to make it unique, and drop the magic
define vc4_crtc vc4_kms_crtc
define to_vc4_crtc to_vc4_kms_crtc
that renamed half the variable and function names in a slightly
unexpected way.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Mateusz Kwiatkowski [Wed, 14 Jul 2021 23:08:01 +0000 (01:08 +0200)]
drm/vc4: Allow setting the TV norm via module parameter
Similar to the ch7006 and nouveau drivers, introduce a "tv_mode" module
parameter that allow setting the TV norm by specifying vc4.tv_norm= on
the kernel command line.
If that is not specified, try inferring one of the most popular norms
(PAL or NTSC) from the video mode specified on the command line. On
Raspberry Pis, this causes the most common cases of the sdtv_mode
setting in config.txt to be respected.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Dave Stevenson [Thu, 7 Jan 2021 16:30:55 +0000 (16:30 +0000)]
drm/atomic: Don't fixup modes that haven't been reset
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dave Stevenson [Tue, 19 May 2020 15:20:30 +0000 (16:20 +0100)]
drm/vc4: Add FKMS as an acceptable node for dma ranges.
Under FKMS, the firmware (via FKMS) also requires the VideoCore cache
aliases for image planes, as defined by the dma-ranges under /soc.
Add rpi-firmware-kms to the list of acceptable nodes to look for
to copy dma config from.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Dom Cobley [Thu, 7 Apr 2022 17:23:07 +0000 (18:23 +0100)]
raspberrypi-firmware: Update mailbox commands
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Andreas Blaesius [Wed, 5 Jan 2022 19:38:39 +0000 (20:38 +0100)]
Use GitHubs issue form for bug reports
Use GitHubs issue form for bug reports.
- modern look
- user don't need to mess with given markdown parts while filling the issue template
Setup config.yml for general questions and problems with the Raspbian distribution packages.
Update issue templates (#2736)
Dave Stevenson [Wed, 8 Mar 2023 15:28:19 +0000 (15:28 +0000)]
workflows: We all love checkpatch, so add it to the CI workflows
This is currently running on defaults, so the --strict desired
for media drivers and similar won't be observed. That may be
possible to add later.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
.github: Add Github Workflow for KUnit
Now that we have some KUnit coverage, let's add a github actions file to
run them on each push or pull request.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
.github/workflows: Add dtoverlaycheck workflow
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
.github/workflows: Create workflow to CI kernel builds
Builds the bcmrpi, bcm2709, bcm2711, and bcm2835 32 bit kernels,
and defconfig and bcm2711 64bit kernels, saving the artifacts for
7 days.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
.github: Skip broken Generic DRM/KMS Unit Tests
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Set warnings-as-errors for builds
To avoid code with build warnings being introduced into the tree, force
CONFIG_WERROR=y in the build workflow.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Correct kernel builds artifacts
Modify the kernel build workflow to create artifacts with the correct
names and structure, both as an example of what we expect and in case
anyone wants to use the output.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Switch to a matrix build
Remove the per-build duplication by putting build parameters in a
matrix.
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
.github/workflows: Retain artifacts for 90 days
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Greg Kroah-Hartman [Fri, 16 Feb 2024 18:10:57 +0000 (19:10 +0100)]
Linux 6.6.17
Link: https://lore.kernel.org/r/20240213171852.948844634@linuxfoundation.org
Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Allen Pais <apais@linux.microsoft.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Link: https://lore.kernel.org/r/20240214142247.920076071@linuxfoundation.org
Tested-by: Allen Pais <apais@linux.microsoft.com>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: kernelci.org bot <bot@kernelci.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso [Wed, 7 Feb 2024 17:49:51 +0000 (18:49 +0100)]
netfilter: nft_set_rbtree: skip end interval element from gc
commit
60c0c230c6f046da536d3df8b39a20b9a9fd6af0 upstream.
rbtree lazy gc on insert might collect an end interval element that has
been just added in this transactions, skip end interval elements that
are not yet active.
Fixes:
f718863aca46 ("netfilter: nft_set_rbtree: fix overlap expiration walk")
Cc: stable@vger.kernel.org
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Furong Xu [Sat, 3 Feb 2024 05:31:33 +0000 (13:31 +0800)]
net: stmmac: xgmac: fix a typo of register name in DPP safety handling
commit
1ce2654d87e2fb91fea83b288bd9b2641045e42a upstream.
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes:
46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 24 Jan 2024 15:53:07 +0000 (16:53 +0100)]
ALSA: usb-audio: Sort quirk table entries
commit
668abe6dc7b61941fa5c724c06797efb0b87f070 upstream.
The quirk table entries should be put in the USB ID order, but some
entries have been put in random places. Re-sort them.
Fixes:
bf990c102319 ("ALSA: usb-audio: add quirk to fix Hamedal C20 disconnect issue")
Fixes:
fd28941cff1c ("ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless")
Fixes:
dfd5fe19db7d ("ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless")
Fixes:
4a63e68a2951 ("ALSA: usb-audio: Fix microphone sound on Nexigo webcam.")
Fixes:
7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Fixes:
4fb7c24f69c4 ("ALSA: usb-audio: Add quirk for Fiero SC-01")
Fixes:
2307a0e1ca0b ("ALSA: usb-audio: Add quirk for Fiero SC-01 (fw v1.0.0)")
Link: https://lore.kernel.org/r/20240124155307.16996-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Horman [Thu, 8 Feb 2024 09:48:27 +0000 (09:48 +0000)]
net: stmmac: xgmac: use #define for string constants
commit
1692b9775e745f84b69dc8ad0075b0855a43db4e upstream.
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes:
46eba193d04f ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/
c25eb595-8d91-40ea-9f52-
efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/
202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jens Axboe [Mon, 29 Jan 2024 19:00:58 +0000 (12:00 -0700)]
io_uring/net: limit inline multishot retries
Commit
76b367a2d83163cf19173d5cb0b562acbabc8eac upstream.
If we have multiple clients and some/all are flooding the receives to
such an extent that we can retry a LOT handling multishot receives, then
we can be starving some clients and hence serving traffic in an
imbalanced fashion.
Limit multishot retry attempts to some arbitrary value, whose only
purpose serves to ensure that we don't keep serving a single connection
for way too long. We default to 32 retries, which should be more than
enough to provide fairness, yet not so small that we'll spend too much
time requeuing rather than handling traffic.
Cc: stable@vger.kernel.org
Depends-on:
704ea888d646 ("io_uring/poll: add requeue return code from poll multishot handling")
Depends-on:
1e5d765a82f ("io_uring/net: un-indent mshot retry path in io_recv_finish()")
Depends-on:
e84b01a880f6 ("io_uring/poll: move poll execution helpers higher up")
Fixes:
b3fdea6ecb55 ("io_uring: multishot recv")
Fixes:
9bb66906f23e ("io_uring: support multishot in recvmsg")
Link: https://github.com/axboe/liburing/issues/1043
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jens Axboe [Mon, 29 Jan 2024 18:57:11 +0000 (11:57 -0700)]
io_uring/poll: add requeue return code from poll multishot handling
Commit
704ea888d646cb9d715662944cf389c823252ee0 upstream.
Since our poll handling is edge triggered, multishot handlers retry
internally until they know that no more data is available. In
preparation for limiting these retries, add an internal return code,
IOU_REQUEUE, which can be used to inform the poll backend about the
handler wanting to retry, but that this should happen through a normal
task_work requeue rather than keep hammering on the issue side for this
one request.
No functional changes in this patch, nobody is using this return code
just yet.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / platform / kernel / linux-rpi.git / log