Ido Schimmel [Wed, 15 Jul 2020 08:27:27 +0000 (11:27 +0300)]
mlxsw: core_acl_flex_actions: Work around hardware limitation
In the policy engine, each ACL rule points to an action block where the
ACL actions are stored. Each action block consists of one or more action
sets. Each action set holds one or more individual actions, up to a
maximum queried from the device. For example:
Action set #1 Action set #2
+----------+ +--------------+ +--------------+
| ACL rule +----------> Action #1 | +-----> Action #4 |
+----------+ +--------------+ | +--------------+
| Action #2 | | | Action #5 |
+--------------+ | +--------------+
| Action #3 +------+ | |
+--------------+ +--------------+
<---------+ Action block +----------------->
The hardware has a limitation that prevents a policing action
(MLXSW_AFA_POLCNT_CODE when used with a policer, not a counter) from
being configured in the same action set with a trap action (i.e.,
MLXSW_AFA_TRAP_CODE or MLXSW_AFA_TRAPWU_CODE). Note that the latter used
to implement multiple actions: 'trap', 'mirred', 'drop'.
Work around this limitation by teaching mlxsw_afa_block_append_action()
to create a new action set not only when there is no more room left in
the current set, but also when there is a conflict between previously
mentioned actions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Wed, 15 Jul 2020 08:27:26 +0000 (11:27 +0300)]
mlxsw: spectrum_policer: Add devlink resource support
Expose via devlink-resource the maximum number of single-rate policers
and their current occupancy. Example:
$ devlink resource show pci/0000:01:00.0
...
name global_policers size 1000 unit entry dpipe_tables none
resources:
name single_rate_policers size 968 occ 0 unit entry dpipe_tables none
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Wed, 15 Jul 2020 08:27:25 +0000 (11:27 +0300)]
mlxsw: spectrum_policer: Add policer core
Add common code to handle all policer-related functionality in mlxsw.
Currently, only policer for policy engines are supported, but it in the
future more policer families will be added such as CPU (trap) policers
and storm control policers.
The API allows different modules to add / delete policers and read their
drop counter.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Wed, 15 Jul 2020 08:27:24 +0000 (11:27 +0300)]
mlxsw: resources: Add resource identifier for global policers
Add a resource identifier for maximum global policers so that it could
be later used to query the information from firmware.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Wed, 15 Jul 2020 08:27:23 +0000 (11:27 +0300)]
mlxsw: reg: Add policer bandwidth limits
Add policer bandwidth limits for both rate and burst size so that they
could be enforced by a later patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Luo bin [Wed, 15 Jul 2020 07:30:23 +0000 (15:30 +0800)]
hinic: add firmware update support
add support to update firmware by the devlink flashing API
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Suraj Upadhyay [Tue, 14 Jul 2020 14:23:28 +0000 (19:53 +0530)]
decnet: dn_dev: Remove an unnecessary label.
Remove the unnecessary label from dn_dev_ioctl() and make its error
handling simpler to read.
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Thu, 9 Jul 2020 20:17:33 +0000 (23:17 +0300)]
docs: networking: timestamping: add section for stacked PHC devices
The concept of timestamping DSA switches / Ethernet PHYs is becoming
more and more popular, however the Linux kernel timestamping code has
evolved quite organically and there's layers upon layers of new and old
code that need to work together for things to behave as expected.
Add this chapter to explain what the overall goals are.
Loosely based upon this email discussion plus some more info:
https://lkml.org/lkml/2020/7/6/481
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander A. Klimov [Thu, 9 Jul 2020 20:49:25 +0000 (22:49 +0200)]
net: sundance: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
YueHaibing [Wed, 15 Jul 2020 02:52:03 +0000 (10:52 +0800)]
netpoll: Remove unused inline function netpoll_netdev_init()
commit
d565b0a1a9b6 ("net: Add Generic Receive Offload infrastructure")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 15 Jul 2020 02:36:13 +0000 (10:36 +0800)]
mptcp: Remove unused inline function mptcp_rcv_synsent()
commit
263e1201a2c3 ("mptcp: consolidate synack processing.")
left behind this, remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 15 Jul 2020 02:31:19 +0000 (10:31 +0800)]
net: flow: Remove unused inline function
It is not used since commit
09c7570480f7 ("xfrm: remove flow cache")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Wed, 15 Jul 2020 02:18:46 +0000 (10:18 +0800)]
cipso: Remove unused inline functions
They are not used any more since commit
b1edeb102397 ("netlabel: Replace
protocol/NetLabel linking with refrerence counts")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jul 2020 00:04:28 +0000 (17:04 -0700)]
Merge branch 'udp_tunnel-NIC-RX-port-offload-infrastructure'
Jakub Kicinski says:
====================
udp_tunnel: NIC RX port offload infrastructure
This set of patches converts further drivers to use the new
infrastructure to UDP tunnel port offload merged in
commit
0ea460474d70 ("Merge branch 'udp_tunnel-add-NIC-RX-port-offload-infrastructure'").
v3:
- fix a W=1 build warning in qede.
v2:
- fix a W=1 build warning in xgbe,
- expand the size of tables for lio.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:30 +0000 (12:18 -0700)]
qlcnic: convert to new udp_tunnel_nic infra
Straightforward conversion to new infra, 1 VxLAN port, handler
may sleep.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:29 +0000 (12:18 -0700)]
qede: convert to new udp_tunnel_nic infra
Covert to new infra. Looks like this driver was not doing
ref counting, and sleeping in the callback.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:28 +0000 (12:18 -0700)]
fm10k: convert to new udp_tunnel_nic infra
Straightforward conversion to new infra. Driver restores info
after close/open cycle by calling its internal restore function
so just use that, no need for udp_tunnel_nic_reset_ntf() here.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:27 +0000 (12:18 -0700)]
liquidio_vf: convert to new udp_tunnel_nic infra
Carbon copy of the previous change.
This driver is just a super thin FW interface, but Derek let us
know the table has 1024 entries.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:26 +0000 (12:18 -0700)]
liquidio: convert to new udp_tunnel_nic infra
This driver is just a super thin FW interface, but Derek let us
know the table has 1024 entries.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:25 +0000 (12:18 -0700)]
enic: convert to new udp_tunnel_nic infra
Convert to new infra, now the refcounting will be correct,
and driver gets port replay of other ports when offloaded
port gets removed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:24 +0000 (12:18 -0700)]
cxgb4: convert to new udp_tunnel_nic infra
Convert to new infra, this driver is very simple. The check of
adapter->rawf_cnt in cxgb_udp_tunnel_unset_port() is kept from
the old port deletion function but it's dodgy since nothing ever
updates that member once its set during init. Also .set_port
callback always adds the raw mac filter..
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:23 +0000 (12:18 -0700)]
bnx2x: convert to new udp_tunnel_nic infra
Fairly straightforward conversion - no need to keep track
of the use count, and replay when ports get removed, also
callbacks can just sleep.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:22 +0000 (12:18 -0700)]
xgbe: convert to new udp_tunnel_nic infra
Make use of the new udp_tunnel_nic infra. Don't clear the features
when VxLAN port is not present to make all drivers behave the same.
Driver will now (until we address the problem in the core) leave
the RX UDP tunnel feature always on, since this is what most drivers
do.
Remove the list of VxLAN ports, just program the one core told us to.
The driver seem to want to clear the VxLAN ports on close but it
doesn't seem to flush the port list properly so it'd get wrong
use counts after close/open. Again since it calls its own open
handler we need the reset notification hack.
v2:
- fix kbuild warning
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:21 +0000 (12:18 -0700)]
xgbe: switch to more generic VxLAN detection
Instead of looping though the list of ports just check
if the geometry of the packet is correct for VxLAN.
HW most likely doesn't care about the exact port, anyway,
since only first port is actually offloaded, and this way
we won't have to maintain the port list at all.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:20 +0000 (12:18 -0700)]
be2net: convert to new udp_tunnel_nic infra
Convert be2net to new udp_tunnel_nic infra. NIC only takes one VxLAN
port. Remove the port tracking using a list. The warning in
be_work_del_vxlan_port() looked suspicious - like the driver expected
ports to be removed in order of addition.
be2net unregisters ports when going down and re-registers them (for
skyhawk) when coming up, but it never checks if the device is up
in the add_port / del_port callbacks. Make it use
UDP_TUNNEL_NIC_INFO_OPEN_ONLY. Sadly this driver calls its own
open/close functions directly so the udp_tunnel_nic_reset_ntf()
workaround is needed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 14 Jul 2020 19:18:19 +0000 (12:18 -0700)]
nfp: convert to new udp_tunnel_nic infra
NFP conversion is pretty straightforward. We want to be able
to sleep, and only get callbacks when the device is open.
NFP did not ask for port replay when ports were removed, now
new infra will provide this feature for free.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 15 Jul 2020 00:00:52 +0000 (17:00 -0700)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-14
The following pull-request contains BPF updates for your *net-next* tree.
We've added 21 non-merge commits during the last 1 day(s) which contain
a total of 20 files changed, 308 insertions(+), 279 deletions(-).
The main changes are:
1) Fix selftests/bpf build, from Alexei.
2) Fix resolve_btfids build issues, from Jiri.
3) Pull usermode-driver-cleanup set, from Eric.
4) Two minor fixes to bpfilter, from Alexei and Masahiro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 18:35:01 +0000 (20:35 +0200)]
ksz884x: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.
When memory is allocated in 'ksz_alloc_desc()', GFP_KERNEL can be used
because a few lines below, GFP_KERNEL is also used in the
'ksz_alloc_soft_desc()' calls.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 22:07:17 +0000 (15:07 -0700)]
Merge branch 'r8169-add-support-for-RTL8125B'
Heiner Kallweit says:
====================
r8169: add support for RTL8125B
This series adds support for RTL8125B rev.b.
Tested with a Delock 89564 PCIe card.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 14 Jul 2020 15:46:03 +0000 (17:46 +0200)]
r8169: add support for RTL8125B
Add support for RTL8125B rev.b. In my tests 2.5Gbps worked well
w/o firmware, however for a stable link at 1Gbps firmware revision
0.0.2 is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 14 Jul 2020 15:45:03 +0000 (17:45 +0200)]
net: phy: realtek: add support for RTL8125B-internal PHY
Realtek assigned a new PHY ID for the RTL8125B-internal PHY.
It's however compatible with the RTL8125A-internal PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 21:53:45 +0000 (14:53 -0700)]
Merge branch 's390-qeth-next'
Julian Wiedmann says:
====================
s390/qeth: updates 2020-07-14
please apply the following patch series for qeth to netdev's net-next tree.
This brings a mix of cleanups for various parts of the control code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:23:05 +0000 (16:23 +0200)]
s390/qeth: constify the MPC initialization data
We're not modifying these data blobs, so mark them as constant.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:23:04 +0000 (16:23 +0200)]
s390/qeth: unify RX-mode hashtables
To keep track of the addresses programmed from an RX modeset, we have
two separate hashtables (L2: mac_htable, L3: ip_mc_htable).
These are never used at the same time, so unify them into a single
rx_mode_addrs hashtable.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:23:03 +0000 (16:23 +0200)]
s390/qeth: cleanup OAT code
While initially just trying to fix up the indentation, condense a few
lines and get rid of a goto label.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:23:02 +0000 (16:23 +0200)]
s390/qeth: clean up a magic number in the OAT callback
Use the correct struct member instead of hardcoding its offset.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:23:01 +0000 (16:23 +0200)]
s390/qeth: use u64_to_user_ptr() in the OAT code
Use the correct helper for casting to a user pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:23:00 +0000 (16:23 +0200)]
s390/qeth: clean up error handling for isolation mode cmds
As the cmd IO path has learned to propagate errnos back to its callers,
let them deal with errors instead of trying to restore their previous
configuration from within the IO error path.
Also translate the HW error to a meaningful errno, instead of returning
-EIO for all cases (and don't map this to -EOPNOTSUPP later on...).
While at it, add a READ_ONCE() / WRITE_ONCE() pair to ensure that the
data path always sees a valid isolation mode during reconfiguration.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:22:59 +0000 (16:22 +0200)]
s390/qeth: don't clear the configured isolation mode
When qeth_set_access_ctrl_online() is called during the device's
initialization and discovers that isolation mode isn't supported, don't
clear the user's currently configured mode.
They intentionally choose to operate the device in this specific mode,
and degrading the isolation is not an option.
Only adjust the configuration when called via sysfs (ie. fallback = 1),
and here follow the common pattern and restore it from prev_isolation.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:22:58 +0000 (16:22 +0200)]
s390/qeth: only init the isolation mode when necessary
A newly initialized device defaults to ISOLATION_MODE_NONE, don't bother
with programming this a second time.
Then remove the OSD/OSX check, it's already done in the sysfs path
whenever the user actually changes the configuration.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:22:57 +0000 (16:22 +0200)]
s390/qeth: fine-tune errno when cmds are cancelled
If we cancel all pending cmds (eg. when tearing down the device), don't
blame it on an IO error.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julian Wiedmann [Tue, 14 Jul 2020 14:22:56 +0000 (16:22 +0200)]
s390/qeth: reject unsupported link type earlier
Rather than delaying the decision until netdev setup, immediately reject
a device when we discover that it has an unsupported link type
(ie. Token Ring).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 21:50:50 +0000 (14:50 -0700)]
Merge branch 'mlxsw-Mirror-to-CPU-preparations'
Ido Schimmel says:
====================
mlxsw: Mirror to CPU preparations
A future patch set will add the ability to trap packets that were
dropped due to buffer related reasons (e.g., early drop). Internally
this is implemented by mirroring these packets towards the CPU port.
This patch set adds the required infrastructure to enable such
mirroring.
Patches #1-#2 extend two registers needed for above mentioned
functionality.
Patches #3-#6 gradually add support for setting the mirroring target of
a SPAN (mirroring) agent as the CPU port. This is only supported from
Spectrum-2 onwards, so an error is returned for Spectrum-1.
Patches #7-#8 add the ability to set a policer on a SPAN agent. This is
required because unlike regularly trapped packets, a policer cannot be
set on the trap group with which the mirroring trap is associated.
Patches #9-#12 parse the mirror reason field from the Completion Queue
Element (CQE). Unlike other trapped packets, the trap identifier of
mirrored packets only indicates that the packet was mirrored, but not
why. The reason (e.g., tail drop) is encoded in the mirror reason field.
Patch #13 utilizes the mirror reason field in order to lookup the
matching Rx listener. This allows us to maintain the abstraction that an
Rx listener is mapped to a single trap reason. Without taking the mirror
reason into account we would need to register a single Rx listener for
all mirrored packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:06 +0000 (17:21 +0300)]
mlxsw: core: Use mirror reason during Rx listener lookup
The Rx listener abstraction allows the switch driver (e.g.,
mlxsw_spectrum) to register a function that is called when a packet is
received (trapped) for a specific reason.
Up until now, the Rx listener lookup was solely based on the trap
identifier. However, when a packet is mirrored to the CPU the trap
identifier merely indicates that the packet was mirrored, but not why it
was mirrored. This makes it impossible for the switch driver to register
different Rx listeners for different mirror reasons.
Solve this by allowing the switch driver to register a Rx listener with
a mirror reason and by extending the Rx listener lookup to take the
mirror reason into account.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:05 +0000 (17:21 +0300)]
mlxsw: pci: Retrieve mirror reason from CQE during receive
In case the mirror reason is valid, retrieve it into the Rx information
so that it could be used during listener lookup in a later patch.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:04 +0000 (17:21 +0300)]
mlxsw: pci: Add mirror reason field to CQEv2
The Completion Queue Element version 2 (CQEv2) includes a field called
'mirror_reason' which indicates why the packet was mirrored to the CPU.
Add the field so that it can be used by a later patch.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:03 +0000 (17:21 +0300)]
mlxsw: trap: Add trap identifiers for mirrored packets
Packets that are mirrored to the CPU port are trapped with one of eight
trap identifiers. Add them.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 14 Jul 2020 14:21:02 +0000 (17:21 +0300)]
mlxsw: reg: Increase trap identifier to 10 bits
The trap identifier was increased to 10 bits in new versions of the
Programmer's Reference Manual (PRM).
Increase it accordingly in the Host PacKet Trap (HPKT) register and in
the Completion Queue Element (CQE).
This is significant for subsequent patches that will introduce trap
identifiers which utilize the extended range.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:01 +0000 (17:21 +0300)]
mlxsw: spectrum_span: Allow setting policer on a SPAN agent
When mirroring packets to the CPU port the mirrored packets are trapped
to the CPU. However, unlike other traps, it is not possible to set a
policer on the associated trap group. Instead, the policer needs to be
set on the SPAN agent.
Moreover, the policer ID must be within a specified range: From a
configurable (even) base ID to this base plus the maximum number of SPAN
agents.
While the immediate use case is to set the policer on a SPAN agent that
mirrors to the CPU port, a policer can be set on any SPAN agent.
Therefore, the operation is implemented for all SPAN agent types.
Extend the SPAN agent request API to allow passing the desired policer
ID that should be bound to the SPAN agent. Return an error for
Spectrum-1, as it does not support policer setting on a SPAN agent.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:21:00 +0000 (17:21 +0300)]
mlxsw: spectrum_span: Allow passing parameters to SPAN agents
Currently, the only parameter of a SPAN agent is the netdev which
the SPAN agent should mirror to.
The next patch will add the ability to request a SPAN agent that mirrors
to a specific netdev and has a specific policer ID bound to it. This is
required when mirroring packets to the CPU port.
Therefore, encapsulate the sole parameter to mlxsw_sp_span_agent_get()
in a structure, so that it could later be extended with policer
information.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:59 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Add support for mirroring towards CPU port
The Spectrum-2 and Spectrum-3 ASICs are able to mirror packets towards
the CPU. These packets are then trapped like any other packet, but with
a special packet trap and additional metadata such as why the packet was
mirrored.
The ability to mirror packets towards the CPU will be utilized by a
subsequent patch set that will mirror packets that were dropped by the
ASIC for various buffer-related reasons, such as tail-drop and
early-drop.
Add mirroring towards the CPU as a new SPAN agent type and re-use the
functions that mirror to a physical port where possible.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:58 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Do not dereference destination netdev
Currently, the destination netdev to which we mirror must be a valid
netdev. However, this is going to change with the introduction of
mirroring towards the CPU port, as the CPU port does not have a backing
netdev.
Avoid dereferencing the destination netdev when it is not clear if it is
valid or not.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:57 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Add driver private info to parms_set() callback
The parms_set() callback is supposed to fill in the parameters for the
SPAN agent, such as the destination port and encapsulation info, if any.
When mirroring to the CPU port we cannot resolve the destination port
(the CPU port) without access to the driver private info.
Pass the driver private info to parms_set() callback so that it could be
used later on to resolve the CPU port.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Tue, 14 Jul 2020 14:20:56 +0000 (17:20 +0300)]
mlxsw: spectrum_span: Add per-ASIC SPAN agent operations
The various SPAN agent types differ in their mirror targets (i.e.,
physical port netdev vs. VLAN netdev) and the encapsulation headers that
they need to encapsulate the mirrored packets with.
The Spectrum-2 and Spectrum-3 ASICs support a SPAN agent type that is
able to mirror towards the CPU, whereas the Spectrum-1 ASIC does not.
Prepare for the addition of this new SPAN agent type by splitting the
SPAN agent operations to be per-ASIC.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 14 Jul 2020 14:20:55 +0000 (17:20 +0300)]
mlxsw: reg: add mirroring_pid_base to MOGCR register
Allow setting mirroring_pid_base using MOGCR register.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amit Cohen [Tue, 14 Jul 2020 14:20:54 +0000 (17:20 +0300)]
mlxsw: reg: Add session_id and pid to MPAT register
Allow setting session_id and pid as part of port analyzer
configurations.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 09:14:12 +0000 (11:14 +0200)]
net: neterion: vxge: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below. No GFP_
flag needs to be corrected.
It has been compile tested.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 09:06:20 +0000 (11:06 +0200)]
net: neterion: s2io: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'init_shared_mem()' GFP_KERNEL can be used
because this flag is already used to allocate some memory in this function.
While at it, update some debug message to match the new function names.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Tue, 14 Jul 2020 07:52:24 +0000 (09:52 +0200)]
lan743x: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'lan743x_tx_ring_cleanup()' and
'lan743x_rx_ring_init()', GFP_KERNEL can be used because this flag is
already used to allocate some memory in these functions.
While at it, remove a useless (void *) casting in the first hunk in so that
the code is more consistent.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 20:46:43 +0000 (13:46 -0700)]
Merge branch 'bridge-mrp-Add-support-for-interconnect-ring'
Horatiu Vultur says:
====================
bridge: mrp: Add support for interconnect ring
This patch series extends existing MRP to add support for interconnect ring. An
interconnect ring is a ring that connects 2 rings. In this way is possible to
connect multiple rings. Each interconnect ring is form of 4 nodes, in which 3
have the role MIC(Media Redundancy Interconnect Client) and one has the role
MIM(Media Redundancy Interconnect Manager). All these nodes need to have the
same ID and the ID needs to be unique between multiple interconnect rings. And 2
nodes needs to be part of one ring and the other 2 nodes needs to be part of the
other ring that is connected.
+---------+
| |
+----------| MRM |---------------+
| | | |
| +---------+ |
| |
| |
| |
+--------------+ +-----------------+
| | | |
| MRC/MIC |------------------| MRC/MIM |
| | | |
+--------------+ +-----------------+
| |
|Interconnect port |Interconnect port
| |
| |
+--------------+ +-----------------+
| | | |
| MRC/MIC |----------------- | MRC/MIC |
| | | |
+--------------+ +-----------------+
| |
| |
| +---------+ |
| | | |
+----------| MRM |----------------+
| |
+---------+
Each node in a ring needs to have one of the following ring roles, MRM or MRC.
And it can also have an interconnect role like MIM or MIC if it is part of an
interconnect ring. In the figure above the MRM doesn't have any interconnect
role but the MRC from the top ring have the interconnect roles MIC respectively
MIM. Therefore it is not possible for a node to have only an interconnect role.
There are 2 ways for interconnect ring to detect when is open or closed:
1. To use CCM frames on the interconnect port to detect when the interconnect
link goes down/up. This mode is called LC-mode.
2. To send InTest frames on all 3 ports(2 ring ports and 1 interconnect port)
and detect when these frames are received back. This mode is called RC-mode.
This patch series adds support only for RC-mode. Where MIM sends InTest frames
on all 3 ports and detects when it receives back the InTest. When it receives
the InTest it means that the ring is closed so it would set the interconnect
port in blocking state. If it stops receiving the InTest frames then it would
set the port in forwarding state and it would send InTopo frames. These InTopo
frames will be received by MRM nodes and process them. And then the MRM will
send Topo frames in the rings so each client will clear its FDB.
v4:
- always cancel delay work if the MRP instance is deleted or interconnect role
is disabled but allow only to start to send InTest frames only if the role
is MIM.
v3:
- update 'br_mrp_set_in_role' to stop sending test if the role is disabled
and don't allow to set a different interconnect port if there is already
one.
v2:
- rearrange structures not to contain holes
- stop sending MRP_InTest frames when the MRP instance is deleted
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:58 +0000 (09:34 +0200)]
net: bridge: Add port attribute IFLA_BRPORT_MRP_IN_OPEN
This patch adds a new port attribute, IFLA_BRPORT_MRP_IN_OPEN, which
allows to notify the userspace when the node lost the contiuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:57 +0000 (09:34 +0200)]
bridge: mrp: Extend br_mrp_fill_info
This patch extends the function br_mrp_fill_info to return also the
status for the interconnect ring.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:56 +0000 (09:34 +0200)]
bridge: uapi: mrp: Extend MRP_INFO attributes for interconnect status
Extend the existing MRP_INFO to return status of MRP interconnect. In
case there is no MRP interconnect on the node then the role will be
disabled so the other attributes can be ignored.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:55 +0000 (09:34 +0200)]
bridge: mrp: Extend MRP netlink interface for configuring MRP interconnect
This patch extends the existing MRP netlink interface with the following
attributes: IFLA_BRIDGE_MRP_IN_ROLE, IFLA_BRIDGE_MRP_IN_STATE and
IFLA_BRIDGE_MRP_START_IN_TEST. These attributes are similar with their
ring attributes but they apply to the interconnect port.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:54 +0000 (09:34 +0200)]
bridge: mrp: Implement the MRP Interconnect API
Thie patch adds support for MRP Interconnect. Similar with the MRP ring,
if the HW can't generate MRP_InTest frames, then the SW will try to
generate them. And if also the SW fails to generate the frames then an
error is return to userspace.
The forwarding/termination of MRP_In frames is happening in the kernel
and is done by MRP instances.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:53 +0000 (09:34 +0200)]
bridge: switchdev: mrp: Extend MRP API for switchdev for MRP Interconnect
Implement the MRP API for interconnect switchdev. Similar with the other
br_mrp_switchdev function, these function will just eventually call the
switchdev functions: switchdev_port_obj_add/del.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:52 +0000 (09:34 +0200)]
bridge: mrp: Add br_mrp_in_port_open function
This function notifies the userspace when the node lost the continuity
of MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:51 +0000 (09:34 +0200)]
bridge: mrp: Rename br_mrp_port_open to br_mrp_ring_port_open
This patch renames the function br_mrp_port_open to
br_mrp_ring_port_open. In this way is more clear that a ring port lost
the continuity because there will be also a br_mrp_in_port_open.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:50 +0000 (09:34 +0200)]
bridge: mrp: Extend br_mrp for MRP interconnect
This patch extends the 'struct br_mrp' to contain information regarding
the MRP interconnect. It contains the following:
- the interconnect port 'i_port', which is NULL if the node doesn't have
a interconnect role
- the interconnect id, which is similar with the ring id, but this field
is also part of the MRP_InTest frames.
- the interconnect role, which can be MIM or MIC.
- the interconnect state, which can be open or closed.
- the interconnect delayed_work for sending MRP_InTest frames and check
for lost of continuity.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:49 +0000 (09:34 +0200)]
bridge: mrp: Extend bridge interface
This patch adds a new flag(BR_MRP_LOST_IN_CONT) to the net bridge
ports. This bit will be set when the port lost the continuity of
MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:48 +0000 (09:34 +0200)]
bridge: uapi: mrp: Extend MRP attributes for MRP interconnect
Extend the existing MRP netlink attributes to allow to configure MRP
Interconnect:
IFLA_BRIDGE_MRP_IN_ROLE - the parameter type is br_mrp_in_role which
contains the interconnect id, the ring id, the interconnect role(MIM
or MIC) and the port ifindex that represents the interconnect port.
IFLA_BRIDGE_MRP_IN_STATE - the parameter type is br_mrp_in_state which
contains the interconnect id and the interconnect state.
IFLA_BRIDGE_MRP_IN_TEST - the parameter type is br_mrp_start_in_test
which contains the interconnect id, the interval at which to send
MRP_InTest frames, how many test frames can be missed before declaring
the interconnect ring open and the period which represents for how long
to send MRP_InTest frames.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur [Tue, 14 Jul 2020 07:34:47 +0000 (09:34 +0200)]
switchdev: mrp: Extend switchdev API for MRP Interconnect
Extend switchdev API to add support for MRP interconnect. The HW is
notified in the following cases:
SWITCHDEV_OBJ_ID_IN_ROLE_MRP: This is used when the interconnect role
of the node changes. The supported roles are MIM and MIC.
SWITCHDEV_OBJ_ID_IN_STATE_MRP: This is used when the interconnect ring
changes it states to open or closed.
SWITCHDEV_OBJ_ID_IN_TEST_MRP: This is used to start/stop sending
MRP_InTest frames on all MRP ports. This is called only on nodes that
have the interconnect role MIM.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Masahiro Yamada [Wed, 1 Jul 2020 09:26:44 +0000 (18:26 +0900)]
bpfilter: Allow to build bpfilter_umh as a module without static library
Originally, bpfilter_umh was linked with -static only when
CONFIG_BPFILTER_UMH=y.
Commit
8a2cc0505cc4 ("bpfilter: use 'userprogs' syntax to build
bpfilter_umh") silently, accidentally dropped the CONFIG_BPFILTER_UMH=y
test in the Makefile. Revive it in order to link it dynamically when
CONFIG_BPFILTER_UMH=m.
Since commit
b1183b6dca3e ("bpfilter: check if $(CC) can link static
libc in Kconfig"), the compiler must be capable of static linking to
enable CONFIG_BPFILTER_UMH, but it requires more than needed.
To loosen the compiler requirement, I changed the dependency as follows:
depends on CC_CAN_LINK
depends on m || CC_CAN_LINK_STATIC
If CONFIG_CC_CAN_LINK_STATIC in unset, CONFIG_BPFILTER_UMH is restricted
to 'm' or 'n'.
In theory, CONFIG_CC_CAN_LINK is not required for CONFIG_BPFILTER_UMH=y,
but I did not come up with a good way to describe it.
Fixes:
8a2cc0505cc4 ("bpfilter: use 'userprogs' syntax to build bpfilter_umh")
Reported-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Michal Kubecek <mkubecek@suse.cz>
Link: https://lore.kernel.org/bpf/20200701092644.762234-1-masahiroy@kernel.org
Alexei Starovoitov [Tue, 14 Jul 2020 19:31:45 +0000 (12:31 -0700)]
bpfilter: Initialize pos variable
Make sure 'pos' is initialized to zero before calling kernel_write().
Fixes:
d2ba09c17a06 ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Alexei Starovoitov [Tue, 14 Jul 2020 19:18:01 +0000 (12:18 -0700)]
Merge branch 'usermode-driver-cleanup' of git://git./linux/kernel/git/ebiederm/user-namespace into bpf-next
Jiri Olsa [Tue, 14 Jul 2020 10:25:34 +0000 (12:25 +0200)]
bpf: Fix cross build for CONFIG_DEBUG_INFO_BTF option
Stephen and 0-DAY CI Kernel Test Service reported broken cross build
for arm (arm-linux-gnueabi-gcc (GCC) 9.3.0), with following output:
/tmp/ccMS5uth.s: Assembler messages:
/tmp/ccMS5uth.s:69: Error: unrecognized symbol type ""
/tmp/ccMS5uth.s:82: Error: unrecognized symbol type ""
Having '@object' for .type diretive is wrong because '@' is comment
character for some architectures. Using STT_OBJECT instead that should
work everywhere.
Also using HOST* variables to build resolve_btfids so it's properly
build in crossbuilds (stolen from objtool's Makefile).
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/bpf/20200714102534.299280-2-jolsa@kernel.org
Jiri Olsa [Tue, 14 Jul 2020 10:25:33 +0000 (12:25 +0200)]
bpf: Fix build for disabled CONFIG_DEBUG_INFO_BTF option
Stephen reported following linker warnings on powerpc build:
ld: warning: orphan section `.BTF_ids' from `kernel/trace/bpf_trace.o' being placed in section `.BTF_ids'
ld: warning: orphan section `.BTF_ids' from `kernel/bpf/btf.o' being placed in section `.BTF_ids'
ld: warning: orphan section `.BTF_ids' from `kernel/bpf/stackmap.o' being placed in section `.BTF_ids'
ld: warning: orphan section `.BTF_ids' from `net/core/filter.o' being placed in section `.BTF_ids'
ld: warning: orphan section `.BTF_ids' from `kernel/trace/bpf_trace.o' being placed in section `.BTF_ids'
It's because we generated .BTF_ids section even when
CONFIG_DEBUG_INFO_BTF is not enabled. Fixing this by
generating empty btf_id arrays for this case.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/bpf/20200714102534.299280-1-jolsa@kernel.org
Alexei Starovoitov [Tue, 14 Jul 2020 03:55:48 +0000 (20:55 -0700)]
selftests/bpf: Fix merge conflict resolution
Remove double definition of structs.
Fixes:
71930d61025e ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
David S. Miller [Tue, 14 Jul 2020 01:04:05 +0000 (18:04 -0700)]
Merge git://git./linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-07-13
The following pull-request contains BPF updates for your *net-next* tree.
We've added 36 non-merge commits during the last 7 day(s) which contain
a total of 62 files changed, 2242 insertions(+), 468 deletions(-).
The main changes are:
1) Avoid trace_printk warning banner by switching bpf_trace_printk to use
its own tracing event, from Alan.
2) Better libbpf support on older kernels, from Andrii.
3) Additional AF_XDP stats, from Ciara.
4) build time resolution of BTF IDs, from Jiri.
5) BPF_CGROUP_INET_SOCK_RELEASE hook, from Stanislav.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 20:48:12 +0000 (22:48 +0200)]
wan: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 13 Jul 2020 20:18:45 +0000 (22:18 +0200)]
pcnet32: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'pcnet32_realloc_tx_ring()' and
'pcnet32_realloc_rx_ring()', GFP_ATOMIC must be used because a spin_lock is
hold.
The call chain is:
pcnet32_set_ringparam
** spin_lock_irqsave(&lp->lock, flags);
--> pcnet32_realloc_tx_ring
--> pcnet32_realloc_rx_ring
** spin_unlock_irqrestore(&lp->lock, flags);
When memory is in 'pcnet32_probe1()' and 'pcnet32_alloc_ring()', GFP_KERNEL
can be used.
While at it, update a few comments and pr_err messages to be more in line
with the new function names.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christophe JAILLET [Mon, 13 Jul 2020 19:55:03 +0000 (21:55 +0200)]
amd8111e: switch from 'pci_' to 'dma_' API
The wrappers in include/linux/pci-dma-compat.h should go away.
The patch has been generated with the coccinelle script below and has been
hand modified to replace GPF_ with a correct flag.
It has been compile tested.
When memory is allocated in 'amd8111e_init_ring()', GFP_ATOMIC must be used
because a spin_lock is hold.
One of the call chains is:
amd8111e_open
** spin_lock_irq(&lp->lock);
--> amd8111e_restart
--> amd8111e_init_ring
** spin_unlock_irq(&lp->lock);
The rest of the patch is produced by coccinelle with a few adjustments to
please checkpatch.pl.
@@
@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@
@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@
@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
@@
- PCI_DMA_NONE
+ DMA_NONE
@@
expression e1, e2, e3;
@@
- pci_alloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3;
@@
- pci_zalloc_consistent(e1, e2, e3)
+ dma_alloc_coherent(&e1->dev, e2, e3, GFP_)
@@
expression e1, e2, e3, e4;
@@
- pci_free_consistent(e1, e2, e3, e4)
+ dma_free_coherent(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4, e5;
@@
- pci_map_page(e1, e2, e3, e4, e5)
+ dma_map_page(&e1->dev, e2, e3, e4, e5)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_page(e1, e2, e3, e4)
+ dma_unmap_page(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_map_sg(e1, e2, e3, e4)
+ dma_map_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_sg(e1, e2, e3, e4)
+ dma_unmap_sg(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+ dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_single_for_device(e1, e2, e3, e4)
+ dma_sync_single_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+ dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+ dma_sync_sg_for_device(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 17:34:47 +0000 (19:34 +0200)]
net: wan: cosa: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 17:24:39 +0000 (19:24 +0200)]
net: jme: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 17:14:29 +0000 (19:14 +0200)]
net: ethernet: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 14 Jul 2020 00:40:02 +0000 (17:40 -0700)]
Merge branch 'New-DSA-driver-for-VSC9953-Seville-switch'
Vladimir Oltean says:
====================
New DSA driver for VSC9953 Seville switch
Looking at the Felix and Ocelot drivers, Maxim asked if it would be
possible to use them as a base for a new driver for the Seville switch
inside NXP T1040. Turns out, it is! The result is that the mscc_felix
driver was extended to probe on Seville.
The biggest challenge seems to be getting register read/write API
generic enough to cover such wild bitfield variations between hardware
generations.
Currently, both felix and seville are built under the same kernel config
option (NET_DSA_MSCC_FELIX). This has both some advantages (no need to
duplicate the Lynx PCS code from felix_vsc9959.c) and some disadvantages
(Seville needs to depend on PCI and on ENETC_MDIO). This will be further
refined as time progresses.
The driver has been completely reviewed. Previous submission was here,
it wasn't accepted due to a conflict with Mark Brown's tree, very late
in the release cycle:
https://patchwork.ozlabs.org/project/netdev/cover/
20200531122640.1375715-1-olteanv@gmail.com/
So this is more of a repost, with the only changes being related to
rebasing on top of the cleanup I had to do in Ocelot.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:11 +0000 (19:57 +0300)]
docs: devicetree: add bindings for Seville DSA switch inside Felix driver
There are no non-standard bindings being used. However Felix is a PCI
device and Seville is a platform device. So give an example of device
tree for this switch and document its compatible string.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:10 +0000 (19:57 +0300)]
net: dsa: felix: introduce support for Seville VSC9953 switch
This is another switch from Vitesse / Microsemi / Microchip, that has
10 ports (8 external, 2 internal) and is integrated into the Freescale /
NXP T1040 PowerPC SoC. It is very similar to Felix from NXP LS1028A,
except that this is a platform device and Felix is a PCI device, and it
doesn't support IEEE 1588 and TSN.
Like Felix, this driver configures its own PCS on the internal MDIO bus
using a phy_device abstraction for it (yes, it will be refactored to use
a raw mdio_device, like other phylink drivers do, but let's keep it like
that for now). But unlike Felix, the MDIO bus and the PCS are not from
the same vendor. The PCS is the same QorIQ/Layerscape PCS as found in
Felix/ENETC/DPAA*, but the internal MDIO bus that is used to access it
is actually an instantiation of drivers/net/phy/mdio-mscc-miim.c. But it
would be difficult to reuse that driver (it doesn't even use regmap, and
it's less than 200 lines of code), so we hand-roll here some internal
MDIO bus accessors within seville_vsc9953.c, which serves the purpose of
driving the PCS absolutely fine.
Also, same as Felix, the PCS doesn't support dynamic reconfiguration of
SerDes protocol, so we need to do pre-validation of PHY mode from device
tree and not let phylink change it.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:09 +0000 (19:57 +0300)]
net: dsa: felix: move probing to felix_vsc9959.c
Felix is not actually meant to be a DSA driver only for the switch
inside NXP LS1028A, but an umbrella for all Vitesse / Microsemi /
Microchip switches that are register-compatible with Ocelot and that are
using in DSA mode (with an NPI Ethernet port).
For the dsa_switch_ops exported by the felix driver to be generic enough
to be used by other non-PCI switches, we need to move the PCI-specific
probing to the low-level translation module felix_vsc9959.c. This way,
other switches can have their own probing functions, as platform devices
or otherwise.
This patch also removes the "Felix instance table", which did not stand
the test of time and is unnecessary at this point.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:08 +0000 (19:57 +0300)]
net: mscc: ocelot: extend watermark encoding function
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:07 +0000 (19:57 +0300)]
net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield
Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:06 +0000 (19:57 +0300)]
net: mscc: ocelot: disable flow control on NPI interface
The Ocelot switches do not support flow control on Ethernet interfaces
where a DSA tag must be added. If pause frames are enabled, they will be
encapsulated in the DSA tag just like regular frames, and the DSA master
will not recognize them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:05 +0000 (19:57 +0300)]
net: mscc: ocelot: split writes to pause frame enable bit and to thresholds
We don't want ocelot_port_set_maxlen to enable pause frame TX, just to
adjust the pause thresholds.
Move the unconditional enabling of pause TX to ocelot_init_port. There
is no good place to put such setting because it shouldn't be
unconditional. But at the moment it is, we're not changing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:04 +0000 (19:57 +0300)]
net: dsa: felix: create a template for the DSA tags on xmit
With this patch we try to kill 2 birds with 1 stone.
First of all, some switches that use tag_ocelot.c don't have the exact
same bitfield layout for the DSA tags. The destination ports field is
different for Seville VSC9953 for example. So the choices are to either
duplicate tag_ocelot.c into a new tag_seville.c (sub-optimal) or somehow
take into account a supposed ocelot->dest_ports_offset when packing this
field into the DSA injection header (again not ideal).
Secondly, tag_ocelot.c already needs to memset a 128-bit area to zero
and call some packing() functions of dubious performance in the
fastpath. And most of the values it needs to pack are pretty much
constant (BYPASS=1, SRC_PORT=CPU, DEST=port index). So it would be good
if we could improve that.
The proposed solution is to allocate a memory area per port at probe
time, initialize that with the statically defined bits as per chip
hardware revision, and just perform a simpler memcpy in the fastpath.
Other alternatives have been analyzed, such as:
- Create a separate tag_seville.c: too much code duplication for just 1
bit field difference.
- Create a separate DSA_TAG_PROTO_SEVILLE under tag_ocelot.c, just like
tag_brcm.c, which would have a separate .xmit function. Again, too
much code duplication for just 1 bit field difference.
- Allocate the template from the init function of the tag_ocelot.c
module, instead of from the driver: couldn't figure out a method of
accessing the correct port template corresponding to the correct
tagger in the .xmit function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:03 +0000 (19:57 +0300)]
net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields
Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.
Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.
There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
Felix and Ocelot, which was their hardware-default value, and which
there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
register field at all, and therefore, if we want to have common code
we would be required to not write to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maxim Kochetkov [Mon, 13 Jul 2020 16:57:02 +0000 (19:57 +0300)]
soc: mscc: ocelot: add MII registers description
Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.
Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Mon, 13 Jul 2020 16:57:01 +0000 (19:57 +0300)]
net: mscc: ocelot: convert port registers to regmap
At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.
But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced. The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 13 Jul 2020 15:20:14 +0000 (18:20 +0300)]
devlink: Fix use-after-free when destroying health reporters
Dereferencing the reporter after it was destroyed in order to unlock the
reporters lock results in a use-after-free [1].
Fix this by storing a pointer to the lock in a local variable before
destroying the reporter.
[1]
==================================================================
BUG: KASAN: use-after-free in devlink_health_reporter_destroy+0x15c/0x1b0 net/core/devlink.c:5476
Read of size 8 at addr
ffff8880650fd020 by task syz-executor.1/904
CPU: 0 PID: 904 Comm: syz-executor.1 Not tainted 5.8.0-rc2+ #35
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
print_address_description.constprop.0+0x1c/0x250 mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
devlink_health_reporter_destroy+0x15c/0x1b0 net/core/devlink.c:5476
nsim_dev_health_exit+0x8b/0xe0 drivers/net/netdevsim/health.c:317
nsim_dev_reload_destroy+0x7f/0x110 drivers/net/netdevsim/dev.c:1134
nsim_dev_reload_down+0x6e/0xd0 drivers/net/netdevsim/dev.c:712
devlink_reload+0xc6/0x3b0 net/core/devlink.c:2952
devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987
genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:736 [inline]
genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:672
____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
___sys_sendmsg+0xff/0x170 net/socket.c:2417
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x4748ad
Code: Bad RIP value.
RSP: 002b:
00007fd0358adc38 EFLAGS:
00000246 ORIG_RAX:
000000000000002e
RAX:
ffffffffffffffda RBX:
000000000056bf00 RCX:
00000000004748ad
RDX:
0000000000000000 RSI:
00000000200000c0 RDI:
0000000000000003
RBP:
00000000ffffffff R08:
0000000000000000 R09:
0000000000000000
R10:
0000000000000000 R11:
0000000000000246 R12:
0000000000000000
R13:
00000000004d1a4b R14:
00007fd0358ae6b4 R15:
00007fd0358add80
Allocated by task 539:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
kmalloc include/linux/slab.h:555 [inline]
kzalloc include/linux/slab.h:669 [inline]
__devlink_health_reporter_create+0x91/0x2f0 net/core/devlink.c:5359
devlink_health_reporter_create+0xa1/0x170 net/core/devlink.c:5431
nsim_dev_health_init+0x95/0x3a0 drivers/net/netdevsim/health.c:279
nsim_dev_probe+0xb1e/0xeb0 drivers/net/netdevsim/dev.c:1086
really_probe+0x287/0x6d0 drivers/base/dd.c:525
driver_probe_device+0xfe/0x1d0 drivers/base/dd.c:701
__device_attach_driver+0x21e/0x290 drivers/base/dd.c:807
bus_for_each_drv+0x161/0x1e0 drivers/base/bus.c:431
__device_attach+0x21a/0x360 drivers/base/dd.c:873
bus_probe_device+0x1e6/0x290 drivers/base/bus.c:491
device_add+0xaf2/0x1b00 drivers/base/core.c:2680
nsim_bus_dev_new drivers/net/netdevsim/bus.c:336 [inline]
new_device_store+0x374/0x590 drivers/net/netdevsim/bus.c:215
bus_attr_store+0x75/0xa0 drivers/base/bus.c:122
sysfs_kf_write+0x113/0x170 fs/sysfs/file.c:138
kernfs_fop_write+0x25d/0x480 fs/kernfs/file.c:315
__vfs_write+0x7c/0x100 fs/read_write.c:495
vfs_write+0x265/0x5e0 fs/read_write.c:559
ksys_write+0x12d/0x250 fs/read_write.c:612
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 904:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
slab_free_hook mm/slub.c:1474 [inline]
slab_free_freelist_hook mm/slub.c:1507 [inline]
slab_free mm/slub.c:3072 [inline]
kfree+0xe6/0x320 mm/slub.c:4063
devlink_health_reporter_free net/core/devlink.c:5449 [inline]
devlink_health_reporter_put+0xb7/0xf0 net/core/devlink.c:5456
__devlink_health_reporter_destroy net/core/devlink.c:5463 [inline]
devlink_health_reporter_destroy+0x11b/0x1b0 net/core/devlink.c:5475
nsim_dev_health_exit+0x8b/0xe0 drivers/net/netdevsim/health.c:317
nsim_dev_reload_destroy+0x7f/0x110 drivers/net/netdevsim/dev.c:1134
nsim_dev_reload_down+0x6e/0xd0 drivers/net/netdevsim/dev.c:712
devlink_reload+0xc6/0x3b0 net/core/devlink.c:2952
devlink_nl_cmd_reload+0x2f1/0x7c0 net/core/devlink.c:2987
genl_family_rcv_msg_doit net/netlink/genetlink.c:691 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:736 [inline]
genl_rcv_msg+0x611/0x9d0 net/netlink/genetlink.c:753
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2469
genl_rcv+0x24/0x40 net/netlink/genetlink.c:764
netlink_unicast_kernel net/netlink/af_netlink.c:1303 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1329
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1918
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:672
____sys_sendmsg+0x6d8/0x840 net/socket.c:2363
___sys_sendmsg+0xff/0x170 net/socket.c:2417
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2450
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:359
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The buggy address belongs to the object at
ffff8880650fd000
which belongs to the cache kmalloc-512 of size 512
The buggy address is located 32 bytes inside of
512-byte region [
ffff8880650fd000,
ffff8880650fd200)
The buggy address belongs to the page:
page:
ffffea0001943f00 refcount:1 mapcount:0 mapping:
0000000000000000 index:0xffff8880650ff800 head:
ffffea0001943f00 order:2 compound_mapcount:0 compound_pincount:0
flags: 0x100000000010200(slab|head)
raw:
0100000000010200 ffffea0001a06a08 ffffea00010ad308 ffff88806c402500
raw:
ffff8880650ff800 0000000000100009 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880650fcf00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff8880650fcf80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff8880650fd000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^
ffff8880650fd080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff8880650fd100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Fixes:
3c5584bf0a04 ("devlink: Rework devlink health reporter destructor")
Fixes:
15c724b997a8 ("devlink: Add devlink health port reporters API")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski [Mon, 13 Jul 2020 15:12:07 +0000 (17:12 +0200)]
net: phy: fix mdio-mscc-miim build
PHYLIB is not selected by mdio-mscc-miim but it uses mdio devres helpers.
Explicitly select MDIO_DEVRES in this driver's Kconfig entry.
Reported-by: kernel test robot <lkp@intel.com>
Fixes:
1814cff26739 ("net: phy: add a Kconfig option for mdio_devres")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander A. Klimov [Mon, 13 Jul 2020 14:30:54 +0000 (16:30 +0200)]
isdn/capi: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: David S. Miller <davem@davemloft.net>