usb: gadget: f_ncm: Always set current gadget in ncm_bind()

[ Upstream commit a04224da1f3424b2c607b12a3bd1f0e302fb8231 ]

Previously, gadget assignment to the net device occurred exclusively
during the initial binding attempt.

Nevertheless, the gadget pointer could change during bind/unbind
cycles due to various conditions, including the unloading/loading
of the UDC device driver or the detachment/reconnection of an
OTG-capable USB hub device.

This patch relocates the gether_set_gadget() function out from
ncm_opts->bound condition check, ensuring that the correct gadget
is assigned during each bind request.

The provided logs demonstrate the consistency of ncm_opts throughout
the power cycle, while the gadget may change.

* OTG hub connected during boot up and assignment of gadget and
  ncm_opts pointer

[    2.366301] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105
[    2.366304] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.366306] usb 2-1.5: Product: H2H Bridge
[    2.366308] usb 2-1.5: Manufacturer: Aptiv
[    2.366309] usb 2-1.5: SerialNumber: 13FEB2021
[    2.427989] usb 2-1.5: New USB device found, VID=2996, PID=0105
[    2.428959] dabridge 2-1.5:1.0: dabridge 2-4 total endpoints=5, 0000000093a8d681
[    2.429710] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[    2.429714] dabridge 2-1.5:1.0: Hub 2-2 P(0151) V(06.87)
[    2.429956] dabridge 2-1.5:1.0: All downstream ports in host mode

[    2.430093] gadget 000000003c414d59 ------> gadget pointer

* NCM opts and associated gadget pointer during First ncm_bind

[   34.763929] NCM opts 00000000aa304ac9
[   34.763930] NCM gadget 000000003c414d59

* OTG capable hub disconnecte or assume driver unload.

[   97.203114] usb 2-1: USB disconnect, device number 2
[   97.203118] usb 2-1.1: USB disconnect, device number 3
[   97.209217] usb 2-1.5: USB disconnect, device number 4
[   97.230990] dabr_udc deleted

* Reconnect the OTG hub or load driver assaign new gadget pointer.

[  111.534035] usb 2-1.1: New USB device found, idVendor=2996, idProduct=0120, bcdDevice= 6.87
[  111.534038] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  111.534040] usb 2-1.1: Product: Vendor
[  111.534041] usb 2-1.1: Manufacturer: Aptiv
[  111.534042] usb 2-1.1: SerialNumber: Superior
[  111.535175] usb 2-1.1: New USB device found, VID=2996, PID=0120
[  111.610995] usb 2-1.5: new high-speed USB device number 8 using xhci-hcd
[  111.630052] usb 2-1.5: New USB device found, idVendor=2996, idProduct=0105, bcdDevice=21.02
[  111.630055] usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  111.630057] usb 2-1.5: Product: H2H Bridge
[  111.630058] usb 2-1.5: Manufacturer: Aptiv
[  111.630059] usb 2-1.5: SerialNumber: 13FEB2021
[  111.687464] usb 2-1.5: New USB device found, VID=2996, PID=0105
[  111.690375] dabridge 2-1.5:1.0: dabridge 2-8 total endpoints=5, 000000000d87c961
[  111.691172] dabridge 2-1.5:1.0: P(0105) D(22.06.22) F(17.3.16) H(1.1) high-speed
[  111.691176] dabridge 2-1.5:1.0: Hub 2-6 P(0151) V(06.87)
[  111.691646] dabridge 2-1.5:1.0: All downstream ports in host mode

[  111.692298] gadget 00000000dc72f7a9 --------> new gadget ptr on connect

* NCM opts and associated gadget pointer during second ncm_bind

[  113.271786] NCM opts 00000000aa304ac9 -----> same opts ptr used during first bind
[  113.271788] NCM gadget 00000000dc72f7a9 ----> however new gaget ptr, that will not set
                                                 in net_device due to ncm_opts->bound = true

Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Link: https://lore.kernel.org/r/20231020153324.82794-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: host: xhci: Avoid XHCI resume delay if SSUSB device is not present

[ Upstream commit 6add6dd345cb754ce18ff992c7264cabf31e59f6 ]

There is a 120ms delay implemented for allowing the XHCI host controller to
detect a U3 wakeup pulse.  The intention is to wait for the device to retry
the wakeup event if the USB3 PORTSC doesn't reflect the RESUME link status
by the time it is checked.  As per the USB3 specification:

  tU3WakeupRetryDelay ("Table 7-12. LTSSM State Transition Timeouts")

This would allow the XHCI resume sequence to determine if the root hub
needs to be also resumed.  However, in case there is no device connected,
or if there is only a HSUSB device connected, this delay would still affect
the overall resume timing.

Since this delay is solely for detecting U3 wake events (USB3 specific)
then ignore this delay for the disconnected case and the HSUSB connected
only case.

[skip helper function, rename usb3_connected variable -Mathias ]

Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231019102924.2797346-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix error handling of __get_node_page

[ Upstream commit 9b4c8dd99fe48721410741651d426015e03a4b7a ]

Use f2fs_handle_error to record inconsistent node block error
and return -EFSCORRUPTED instead of -EINVAL.

Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

f2fs: fix error path of __f2fs_build_free_nids

[ Upstream commit a5e80e18f268ea7c7a36bc4159de0deb3b5a2171 ]

If NAT is corrupted, let scan_nat_page() return EFSCORRUPTED, so that,
caller can set SBI_NEED_FSCK flag into checkpoint for later repair by
fsck.

Also, this patch introduces a new fscorrupted error flag, and in above
scenario, it will persist the error flag into superblock synchronously
to avoid it has no luck to trigger a checkpoint to record SBI_NEED_FSCK

Signed-off-by: Zhiguo Niu <zhiguo.niu@unisoc.com>
Signed-off-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soundwire: dmi-quirks: update HP Omen match

[ Upstream commit 4ea2b6d3128ea4d502c4015df0dc16b7d1070954 ]

New platforms have a slightly different DMI product name, remove
trailing characters/digits to handle all cases

Closes: https://github.com/thesofproject/linux/issues/4611
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20231013010833.114271-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: ucsi: glink: use the connector orientation GPIO to provide switch events

[ Upstream commit c6165ed2f425c273244191930a47c8be23bc51bd ]

On SM8550, the non-altmode orientation is not given anymore within
altmode events, even with USB SVIDs events.

On the other side, the Type-C connector orientation is correctly
reported by a signal from the PMIC.

Take this gpio signal when we detect some Type-C port activity
to notify any Type-C switches tied to the Type-C port connectors.

Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231002-topic-sm8550-upstream-type-c-orientation-v2-2-125410d3ff95@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: dwc3: core: configure TX/RX threshold for DWC3_IP

[ Upstream commit e72fc8d6a12af7ae8dd1b52cf68ed68569d29f80 ]

In Synopsys's dwc3 data book:
To avoid underrun and overrun during the burst, in a high-latency bus
system (like USB), threshold and burst size control is provided through
GTXTHRCFG and GRXTHRCFG registers.

In Realtek DHC SoC, DWC3 USB 3.0 uses AHB system bus. When dwc3 is
connected with USB 2.5G Ethernet, there will be overrun problem.
Therefore, setting TX/RX thresholds can avoid this issue.

Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/20230912041904.30721-1-stanley_chang@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: qualcomm: phy-qcom-eusb2-repeater: Zero out untouched tuning regs

[ Upstream commit 99a517a582fc1272d1d3cf3b9e671a14d7db77b8 ]

The vendor kernel zeroes out all tuning data outside the init sequence
as part of initialization. Follow suit to avoid UB.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230830-topic-eusb2_override-v2-3-7d8c893d93f6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

phy: qualcomm: phy-qcom-eusb2-repeater: Use regmap_fields

[ Upstream commit 4ba2e52718c0ce4ece6a269bec84319c355c030f ]

Switch to regmap_fields, so that the values written into registers are
sanitized by their explicit sizes and the different registers are
structured in an iterable object to make external changes to the init
sequence simpler.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230830-topic-eusb2_override-v2-2-7d8c893d93f6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dt-bindings: phy: qcom,snps-eusb2-repeater: Add magic tuning overrides

[ Upstream commit c20b59b2996c89c4f072c3312e6210528a298330 ]

The EUSB2 repeater requires some alterations to its init sequence,
depending on board design.

Add support for making the necessary changes to that sequence to make USB
functional on SM8550-based Xperia 1 V.

They all have lackluster description due to lack of information.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230830-topic-eusb2_override-v2-1-7d8c893d93f6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tty: vcc: Add check for kstrdup() in vcc_probe()

[ Upstream commit d81ffb87aaa75f842cd7aa57091810353755b3e6 ]

Add check for the return value of kstrdup() and return the error, if it
fails in order to avoid NULL pointer dereference.

Signed-off-by: Yi Yang <yiyang13@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230904035220.48164-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

thunderbolt: Apply USB 3.x bandwidth quirk only in software connection manager

[ Upstream commit 0c35ac18256942e66d8dab6ca049185812e60c69 ]

This is not needed when firmware connection manager is run so limit this
to software connection manager.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: adc: stm32-adc: harden against NULL pointer deref in stm32_adc_probe()

[ Upstream commit 3a23b384e7e3d64d5587ad10729a34d4f761517e ]

of_match_device() may fail and returns a NULL pointer.

In practice there is no known reasonable way to trigger this, but
in case one is added in future, harden the code by adding the check

Signed-off-by: Zhang Shurong <zhang_shurong@foxmail.com>
Link: https://lore.kernel.org/r/tencent_994DA85912C937E3B5405BA960B31ED90A08@qq.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mfd: intel-lpss: Add Intel Lunar Lake-M PCI IDs

[ Upstream commit e53b22b10c6e0de0cf2a03a92b18fdad70f266c7 ]

Add Intel Lunar Lake-M SoC PCI IDs.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20231002083344.75611-1-jarkko.nikula@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

exfat: support handle zero-size directory

[ Upstream commit dab48b8f2fe7264d51ec9eed0adea0fe3c78830a ]

After repairing a corrupted file system with exfatprogs' fsck.exfat,
zero-size directories may result. It is also possible to create
zero-size directories in other exFAT implementation, such as Paragon
ufsd dirver.

As described in the specification, the lower directory size limits
is 0 bytes.

Without this commit, sub-directories and files cannot be created
under a zero-size directory, and it cannot be removed.

Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Andy Wu <Andy.Wu@sony.com>
Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: Add quirk for Dell Pro Wireless Keyboard and Mouse KM5221W

[ Upstream commit 62cc9c3cb3ec1bf31cc116146185ed97b450836a ]

This device needs ALWAYS_POLL quirk, otherwise it keeps reconnecting
indefinitely.

Reported-by: Robert Ayrapetyan <robert.ayrapetyan@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: hisilicon/qm - prevent soft lockup in receive loop

[ Upstream commit 33fc506d2ac514be1072499a263c3bff8c7c95a0 ]

In the scenario where the accelerator business is fully loaded.
When the workqueue receiving messages and performing callback
processing, there are a large number of messages that need to be
received, and there are continuously messages that have been
processed and need to be received.
This will cause the receive loop here to be locked for a long time.
This scenario will cause watchdog timeout problems on OS with kernel
preemption turned off.

The error logs:
watchdog: BUG: soft lockup - CPU#23 stuck for 23s! [kworker/u262:1:1407]
[ 1461.978428][   C23] Call trace:
[ 1461.981890][   C23]  complete+0x8c/0xf0
[ 1461.986031][   C23]  kcryptd_async_done+0x154/0x1f4 [dm_crypt]
[ 1461.992154][   C23]  sec_skcipher_callback+0x7c/0xf4 [hisi_sec2]
[ 1461.998446][   C23]  sec_req_cb+0x104/0x1f4 [hisi_sec2]
[ 1462.003950][   C23]  qm_poll_req_cb+0xcc/0x150 [hisi_qm]
[ 1462.009531][   C23]  qm_work_process+0x60/0xc0 [hisi_qm]
[ 1462.015101][   C23]  process_one_work+0x1c4/0x470
[ 1462.020052][   C23]  worker_thread+0x150/0x3c4
[ 1462.024735][   C23]  kthread+0x108/0x13c
[ 1462.028889][   C23]  ret_from_fork+0x10/0x18

Therefore, it is necessary to add an actively scheduled operation in the
while loop to prevent this problem.
After adding it, no matter whether the OS turns on or off the kernel
preemption function. Neither will cause watchdog timeout issues.

Signed-off-by: Longfang Liu <liulongfang@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: soc-acpi-cht: Add Lenovo Yoga Tab 3 Pro YT3-X90 quirk

[ Upstream commit 2cb54788393134d8174ee594002baae3ce52c61e ]

The Lenovo Yoga Tab 3 Pro YT3-X90 x86 tablet, which ships with Android with
a custom kernel as factory OS, does not list the used WM5102 codec inside
its DSDT.

Workaround this with a new snd_soc_acpi_intel_baytrail_machines[] entry
which matches on the SST id instead of the codec id like nocodec does,
combined with using a machine_quirk callback which returns NULL on
other machines to skip the new entry on other machines.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231021211534.114991-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Use FIELD_GET() in Sapphire RX 5600 XT Pulse quirk

[ Upstream commit 04e82fa5951ca66495d7b05665eff673aa3852b4 ]

Use FIELD_GET() to remove dependences on the field position, i.e., the
shift value.  No functional change intended.

Separate because this isn't as trivial as the other FIELD_GET() changes.

See 907830b0fc9e ("PCI: Add a REBAR size quirk for Sapphire RX 5600 XT
Pulse")

Link: https://lore.kernel.org/r/20231010204436.1000644-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

misc: pci_endpoint_test: Add Device ID for R-Car S4-8 PCIe controller

[ Upstream commit 6c4b39937f4e65688ea294725ae432b2565821ff ]

Add Renesas R8A779F0 in pci_device_id table so that pci-epf-test
can be used for testing PCIe EP on R-Car S4-8.

Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-16-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: dwc: Add missing PCI_EXP_LNKCAP_MLW handling

[ Upstream commit 89db0793c9f2da265ecb6c1681f899d9af157f37 ]

Update dw_pcie_link_set_max_link_width() to set PCI_EXP_LNKCAP_MLW.

In accordance with the DW PCIe RC/EP HW manuals [1,2,3,...] aside with
the PORT_LINK_CTRL_OFF.LINK_CAPABLE and GEN2_CTRL_OFF.NUM_OF_LANES[8:0]
field there is another one which needs to be updated.

It's LINK_CAPABILITIES_REG.PCIE_CAP_MAX_LINK_WIDTH. If it isn't done at
the very least the maximum link-width capability CSR won't expose the
actual maximum capability.

[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
    Version 4.60a, March 2015, p.1032
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
    Version 4.70a, March 2016, p.1065
[3] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
    Version 4.90a, March 2016, p.1057
...
[X] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint,
      Version 5.40a, March 2019, p.1396
[X+1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
      Version 5.40a, March 2019, p.1266

Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-4-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: dwc: Add dw_pcie_link_set_max_link_width()

[ Upstream commit a9a1bcba90254975d4adbcca53f720318cf81c0c ]

This is a preparation before adding the Max-Link-width capability
setup which would in its turn complete the max-link-width setup
procedure defined by Synopsys in the HW-manual.

Seeing there is a max-link-speed setup method defined in the DW PCIe
core driver it would be good to have a similar function for the link
width setup.

That's why we need to define a dedicated function first from already
implemented but incomplete link-width setting up code.

Link: https://lore.kernel.org/linux-pci/20231018085631.1121289-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Disable ATS for specific Intel IPU E2000 devices

[ Upstream commit a18615b1cfc04f00548c60eb9a77e0ce56e848fd ]

Due to a hardware issue in A and B steppings of Intel IPU E2000, it expects
wrong endianness in ATS invalidation message body. This problem can lead to
outdated translations being returned as valid and finally cause system
instability.

To prevent such issues, add quirk_intel_e2000_no_ats() to disable ATS for
vulnerable IPU E2000 devices.

Link: https://lore.kernel.org/r/20230908143606.685930-3-bartosz.pawlowski@intel.com
Signed-off-by: Bartosz Pawlowski <bartosz.pawlowski@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Extract ATS disabling to a helper function

[ Upstream commit f18b1137d38c091cc8c16365219f0a1d4a30b3d1 ]

Introduce quirk_no_ats() helper function to provide a standard way to
disable ATS capability in PCI quirks.

Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230908143606.685930-2-bartosz.pawlowski@intel.com
Signed-off-by: Bartosz Pawlowski <bartosz.pawlowski@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Use FIELD_GET() to extract Link Width

[ Upstream commit d1f9b39da4a5347150246871325190018cda8cb3 ]

Use FIELD_GET() to extract PCIe Negotiated and Maximum Link Width fields
instead of custom masking and shifting.

Link: https://lore.kernel.org/r/20230919125648.1920-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: drop duplicate include of <linux/bitfield.h>]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: libfc: Fix potential NULL pointer dereference in fc_lport_ptp_setup()

[ Upstream commit 4df105f0ce9f6f30cda4e99f577150d23f0c9c5f ]

fc_lport_ptp_setup() did not check the return value of fc_rport_create()
which can return NULL and would cause a NULL pointer dereference. Address
this issue by checking return value of fc_rport_create() and log error
message on fc_rport_create() failed.

Signed-off-by: Wenchao Hao <haowenchao2@huawei.com>
Link: https://lore.kernel.org/r/20231011130350.819571-1-haowenchao2@huawei.com
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Do error check on own line to split long "if" conditions

[ Upstream commit d15f18053e5cc5576af9e7eef0b2a91169b6326d ]

Placing PCI error code check inside "if" condition usually results in need
to split lines. Combined with additional conditions the "if" condition
becomes messy.

Convert to the usual error handling pattern with an additional variable to
improve code readability. In addition, reverse the logic in
pci_find_vsec_capability() to get rid of &&.

No functional changes intended.

Link: https://lore.kernel.org/r/20230911125354.25501-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
[bhelgaas: PCI_POSSIBLE_ERROR()]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

atm: iphase: Do PCI error checks on own line

[ Upstream commit c28742447ca9879b52fbaf022ad844f0ffcd749c ]

In get_esi() PCI errors are checked inside line-split "if" conditions (in
addition to the file not following the coding style). To make the code in
get_esi() more readable, fix the coding style and use the usual error
handling pattern with a separate variable.

In addition, initialization of 'error' variable at declaration is not
needed.

No functional changes intended.

Link: https://lore.kernel.org/r/20230911125354.25501-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: mvebu: Use FIELD_PREP() with Link Width

[ Upstream commit 408599ec561ad5862cda4f107626009f6fa97a74 ]

mvebu_pcie_setup_hw() setups the Maximum Link Width field in the Link
Capabilities registers using an open-coded variant of FIELD_PREP() with
a literal in shift. Improve readability by using
FIELD_PREP(PCI_EXP_LNKCAP_MLW, ...).

Link: https://lore.kernel.org/r/20230919125648.1920-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: tegra194: Use FIELD_GET()/FIELD_PREP() with Link Width fields

[ Upstream commit 759574abd78e3b47ec45bbd31a64e8832cf73f97 ]

Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting.

Similarly, change custom code that misleadingly used
PCI_EXP_LNKSTA_NLW_SHIFT to prepare value for PCI_EXP_LNKCAP write
to use FIELD_PREP() with correct field define (PCI_EXP_LNKCAP_MLW).

Link: https://lore.kernel.org/r/20230919125648.1920-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: of: Add quirk for mt2701-cs42448 ASoC sound

[ Upstream commit 9e189e80dcb68528dea9e061d9704993f98cb84f ]

These gpio names are due to old DT bindings not following the
"-gpio"/"-gpios" conventions. Handle it using a quirk so the
driver can just look up the GPIOs.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231006-descriptors-asoc-mediatek-v1-1-07fe79f337f5@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: hda: Fix possible null-ptr-deref when assigning a stream

[ Upstream commit f93dc90c2e8ed664985e366aa6459ac83cdab236 ]

While AudioDSP drivers assign streams exclusively of HOST or LINK type,
nothing blocks a user to attempt to assign a COUPLED stream. As
supplied substream instance may be a stub, what is the case when
code-loading, such scenario ends with null-ptr-deref.

Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20231006102857.749143-2-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 9320/1: fix stack depot IRQ stack filter

[ Upstream commit b0150014878c32197cfa66e3e2f79e57f66babc0 ]

Place IRQ handlers such as gic_handle_irq() in the irqentry section even
if FUNCTION_GRAPH_TRACER is not enabled.  Without this, the stack
depot's filter_irq_stacks() does not correctly filter out IRQ stacks in
those configurations, which hampers deduplication and eventually leads
to "Stack depot reached limit capacity" splats with KASAN.

A similar fix was done for arm64 in commit f6794950f0e5ba37e3bbed
("arm64: set __exception_irq_entry with __irq_entry as a default").

Link: https://lore.kernel.org/r/20230803-arm-irqentry-v1-1-8aad8e260b1c@axis.com
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: lenovo: Detect quirk-free fw on cptkbd and stop applying workaround

[ Upstream commit 46a0a2c96f0f47628190f122c2e3d879e590bcbe ]

Built-in firmware of cptkbd handles scrolling by itself (when middle
button is pressed) but with issues: it does not support horizontal and
hi-res scrolling and upon middle button release it sends middle button
click even if there was a scrolling event. Commit 3cb5ff0220e3 ("HID:
lenovo: Hide middle-button press until release") workarounds last
issue but it's impossible to workaround scrolling-related issues
without firmware modification.

Likely, Dennis Schneider has reverse engineered the firmware and
provided an instruction on how to patch it [1]. However,
aforementioned workaround prevents userspace (libinput) from knowing
exact moment when middle button has been pressed down and performing
"On-Button scrolling". This commit detects correctly-behaving patched
firmware if cursor movement events has been received during middle
button being pressed and stops applying workaround for this device.

Link: https://hohlerde.org/rauch/en/elektronik/projekte/tpkbd-fix/
Signed-off-by: Mikhail Khvainitski <me@khvoinitsky.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

jfs: fix array-index-out-of-bounds in diAlloc

[ Upstream commit 05d9ea1ceb62a55af6727a69269a4fd310edf483 ]

Currently there is not check against the agno of the iag while
allocating new inodes to avoid fragmentation problem. Added the check
which is required.

Reported-by: syzbot+79d792676d8ac050949f@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=79d792676d8ac050949f
Signed-off-by: Manas Ghandat <ghandatmanas@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

jfs: fix array-index-out-of-bounds in dbFindLeaf

[ Upstream commit 22cad8bc1d36547cdae0eef316c47d917ce3147c ]

Currently while searching for dmtree_t for sufficient free blocks there
is an array out of bounds while getting element in tp->dm_stree. To add
the required check for out of bound we first need to determine the type
of dmtree. Thus added an extra parameter to dbFindLeaf so that the type
of tree can be determined and the required check can be applied.

Reported-by: syzbot+aea1ad91e854d0a83e04@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=aea1ad91e854d0a83e04
Signed-off-by: Manas Ghandat <ghandatmanas@gmail.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs/jfs: Add validity check for db_maxag and db_agpref

[ Upstream commit 64933ab7b04881c6c18b21ff206c12278341c72e ]

Both db_maxag and db_agpref are used as the index of the
db_agfree array, but there is currently no validity check for
db_maxag and db_agpref, which can lead to errors.

The following is related bug reported by Syzbot:

UBSAN: array-index-out-of-bounds in fs/jfs/jfs_dmap.c:639:20
index 7936 is out of range for type 'atomic_t[128]'

Add checking that the values of db_maxag and db_agpref are valid
indexes for the db_agfree array.

Reported-by: syzbot+38e876a8aa44b7115c76@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=38e876a8aa44b7115c76
Signed-off-by: Juntong Deng <juntong.deng@outlook.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs/jfs: Add check for negative db_l2nbperpage

[ Upstream commit 525b861a008143048535011f3816d407940f4bfa ]

l2nbperpage is log2(number of blks per page), and the minimum legal
value should be 0, not negative.

In the case of l2nbperpage being negative, an error will occur
when subsequently used as shift exponent.

Syzbot reported this bug:

UBSAN: shift-out-of-bounds in fs/jfs/jfs_dmap.c:799:12
shift exponent -16777216 is negative

Reported-by: syzbot+debee9ab7ae2b34b0307@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=debee9ab7ae2b34b0307
Signed-off-by: Juntong Deng <juntong.deng@outlook.com>
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ibmvfc: Remove BUG_ON in the case of an empty event pool

[ Upstream commit b39f2d10b86d0af353ea339e5815820026bca48f ]

In practice the driver should never send more commands than are allocated
to a queue's event pool. In the unlikely event that this happens, the code
asserts a BUG_ON, and in the case that the kernel is not configured to
crash on panic returns a junk event pointer from the empty event list
causing things to spiral from there. This BUG_ON is a historical artifact
of the ibmvfc driver first being upstreamed, and it is well known now that
the use of BUG_ON is bad practice except in the most unrecoverable
scenario. There is nothing about this scenario that prevents the driver
from recovering and carrying on.

Remove the BUG_ON in question from ibmvfc_get_event() and return a NULL
pointer in the case of an empty event pool. Update all call sites to
ibmvfc_get_event() to check for a NULL pointer and perfrom the appropriate
failure or recovery action.

Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20230921225435.3537728-2-tyreld@linux.ibm.com
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: hisi_sas: Set debugfs_dir pointer to NULL after removing debugfs

[ Upstream commit 6de426f9276c448e2db7238911c97fb157cb23be ]

If init debugfs failed during device registration due to memory allocation
failure, debugfs_remove_recursive() is called, after which debugfs_dir is
not set to NULL. debugfs_remove_recursive() will be called again during
device removal. As a result, illegal pointer is accessed.

[ 1665.467244] hisi_sas_v3_hw 0000:b4:02.0: failed to init debugfs!
...
[ 1669.836708] Unable to handle kernel NULL pointer dereference at virtual address 00000000000000a0
[ 1669.872669] pc : down_write+0x24/0x70
[ 1669.876315] lr : down_write+0x1c/0x70
[ 1669.879961] sp : ffff000036f53a30
[ 1669.883260] x29: ffff000036f53a30 x28: ffffa027c31549f8
[ 1669.888547] x27: ffffa027c3140000 x26: 0000000000000000
[ 1669.893834] x25: ffffa027bf37c270 x24: ffffa027bf37c270
[ 1669.899122] x23: ffff0000095406b8 x22: ffff0000095406a8
[ 1669.904408] x21: 0000000000000000 x20: ffffa027bf37c310
[ 1669.909695] x19: 00000000000000a0 x18: ffff8027dcd86f10
[ 1669.914982] x17: 0000000000000000 x16: 0000000000000000
[ 1669.920268] x15: 0000000000000000 x14: ffffa0274014f870
[ 1669.925555] x13: 0000000000000040 x12: 0000000000000228
[ 1669.930842] x11: 0000000000000020 x10: 0000000000000bb0
[ 1669.936129] x9 : ffff000036f537f0 x8 : ffff80273088ca10
[ 1669.941416] x7 : 000000000000001d x6 : 00000000ffffffff
[ 1669.946702] x5 : ffff000008a36310 x4 : ffff80273088be00
[ 1669.951989] x3 : ffff000009513e90 x2 : 0000000000000000
[ 1669.957276] x1 : 00000000000000a0 x0 : ffffffff00000001
[ 1669.962563] Call trace:
[ 1669.965000]  down_write+0x24/0x70
[ 1669.968301]  debugfs_remove_recursive+0x5c/0x1b0
[ 1669.972905]  hisi_sas_debugfs_exit+0x24/0x30 [hisi_sas_main]
[ 1669.978541]  hisi_sas_v3_remove+0x130/0x150 [hisi_sas_v3_hw]
[ 1669.984175]  pci_device_remove+0x48/0xd8
[ 1669.988082]  device_release_driver_internal+0x1b4/0x250
[ 1669.993282]  device_release_driver+0x28/0x38
[ 1669.997534]  pci_stop_bus_device+0x84/0xb8
[ 1670.001611]  pci_stop_and_remove_bus_device_locked+0x24/0x40
[ 1670.007244]  remove_store+0xfc/0x140
[ 1670.010802]  dev_attr_store+0x44/0x60
[ 1670.014448]  sysfs_kf_write+0x58/0x80
[ 1670.018095]  kernfs_fop_write+0xe8/0x1f0
[ 1670.022000]  __vfs_write+0x60/0x190
[ 1670.025472]  vfs_write+0xac/0x1c0
[ 1670.028771]  ksys_write+0x6c/0xd8
[ 1670.032071]  __arm64_sys_write+0x24/0x30
[ 1670.035977]  el0_svc_common+0x78/0x130
[ 1670.039710]  el0_svc_handler+0x38/0x78
[ 1670.043442]  el0_svc+0x8/0xc

To fix this, set debugfs_dir to NULL after debugfs_remove_recursive().

Signed-off-by: Yihang Li <liyihang9@huawei.com>
Signed-off-by: Xingui Yang <yangxingui@huawei.com>
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Link: https://lore.kernel.org/r/1694571327-78697-2-git-send-email-chenxiang66@hisilicon.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

RDMA/hfi1: Use FIELD_GET() to extract Link Width

[ Upstream commit 8bf7187d978610b9e327a3d92728c8864a575ebd ]

Use FIELD_GET() to extract PCIe Negotiated Link Width field instead of
custom masking and shifting, and remove extract_width() which only
wraps that FIELD_GET().

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230919125648.1920-2-ilpo.jarvinen@linux.intel.com
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dean Luick <dean.luick@cornelisnetworks.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: SOF: ipc4: handle EXCEPTION_CAUGHT notification from firmware

[ Upstream commit c1c48fd6bbe788458e3685fea74bdb3cb148ff93 ]

Driver will receive exception IPC message and process it by
snd_sof_dsp_panic.

Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230919092416.4137-10-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: pcrypt - Fix hungtask for PADATA_RESET

[ Upstream commit 8f4f68e788c3a7a696546291258bfa5fdb215523 ]

We found a hungtask bug in test_aead_vec_cfg as follows:

INFO: task cryptomgr_test:391009 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
Call trace:
 __switch_to+0x98/0xe0
 __schedule+0x6c4/0xf40
 schedule+0xd8/0x1b4
 schedule_timeout+0x474/0x560
 wait_for_common+0x368/0x4e0
 wait_for_completion+0x20/0x30
 wait_for_completion+0x20/0x30
 test_aead_vec_cfg+0xab4/0xd50
 test_aead+0x144/0x1f0
 alg_test_aead+0xd8/0x1e0
 alg_test+0x634/0x890
 cryptomgr_test+0x40/0x70
 kthread+0x1e0/0x220
 ret_from_fork+0x10/0x18
 Kernel panic - not syncing: hung_task: blocked tasks

For padata_do_parallel, when the return err is 0 or -EBUSY, it will call
wait_for_completion(&wait->completion) in test_aead_vec_cfg. In normal
case, aead_request_complete() will be called in pcrypt_aead_serial and the
return err is 0 for padata_do_parallel. But, when pinst->flags is
PADATA_RESET, the return err is -EBUSY for padata_do_parallel, and it
won't call aead_request_complete(). Therefore, test_aead_vec_cfg will
hung at wait_for_completion(&wait->completion), which will cause
hungtask.

The problem comes as following:
(padata_do_parallel)                 |
    rcu_read_lock_bh();              |
    err = -EINVAL;                   |   (padata_replace)
                                     |     pinst->flags |= PADATA_RESET;
    err = -EBUSY                     |
    if (pinst->flags & PADATA_RESET) |
        rcu_read_unlock_bh()         |
        return err

In order to resolve the problem, we replace the return err -EBUSY with
-EAGAIN, which means parallel_data is changing, and the caller should call
it again.

v3:
remove retry and just change the return err.
v2:
introduce padata_try_do_parallel() in pcrypt_aead_encrypt and
pcrypt_aead_decrypt to solve the hungtask.

Signed-off-by: Lu Jialin <lujialin4@huawei.com>
Signed-off-by: Guo Zihua <guozihua@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: cs35l56: Use PCI SSID as the firmware UID

[ Upstream commit 1a1c3d794ef65ef2978c5e65e1aed3fe6f014e90 ]

If the driver properties do not define a cirrus,firmware-uid try to get the
PCI SSID as the UID.

On PCI-based systems the PCI SSID is used to uniquely identify the specific
sound hardware. This is the standard mechanism for x86 systems and is the
way to get a unique system identifier for systems that use the CS35L56 on
SoundWire.

For non-SoundWire systems there is no Windows equivalent of the ASoC driver
in I2C/SPI mode. These would be:

1. HDA systems, which are handled by the HDA subsystem.
2. Linux-specific systems.
3. Composite devices where the cs35l56 is not present in ACPI and is
   configured using software nodes.

Case 2 can use the firmware-uid property, though the PCI SSID is supported
as an alternative, as it is the standard PCI mechanism.

Case 3 is a SoundWire system where some other codec is the SoundWire bridge
device and CS35L56 is not listed in ACPI. As these are SoundWire systems
they will normally use the PCI SSID.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230912163207.3498161-5-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: Intel: sof_sdw: Copy PCI SSID to struct snd_soc_card

[ Upstream commit d8b387544ff4d02eda1d1839a0c601de4b037c33 ]

If the PCI SSID has been set in the struct snd_soc_acpi_mach_params,
copy this to struct snd_soc_card so that it can be used by other
ASoC components.

This is important for components that must apply system-specific
configuration.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230912163207.3498161-4-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: SOF: Pass PCI SSID to machine driver

[ Upstream commit ba2de401d32625fe538d3f2c00ca73740dd2d516 ]

Pass the PCI SSID of the audio interface through to the machine driver.
This allows the machine driver to use the SSID to uniquely identify the
specific hardware configuration and apply any platform-specific
configuration.

struct snd_sof_pdata is passed around inside the SOF code, but it then
passes configuration information to the machine driver through
struct snd_soc_acpi_mach and struct snd_soc_acpi_mach_params. So SSID
information has been added to both snd_sof_pdata and
snd_soc_acpi_mach_params.

PCI does not define 0x0000 as an invalid value so we can't use zero to
indicate that the struct member was not written. Instead a flag is
included to indicate that a value has been written to the
subsystem_vendor and subsystem_device members.

sof_pci_probe() creates the struct snd_sof_pdata. It is passed a struct
pci_dev so it can fill in the SSID value.

sof_machine_check() finds the appropriate struct snd_soc_acpi_mach. It
copies the SSID information across to the struct snd_soc_acpi_mach_params.
This done before calling any custom set_mach_params() so that it could be
used by the set_mach_params() callback to apply variant params.

The machine driver receives the struct snd_soc_acpi_mach as its
platform_data.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230912163207.3498161-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: soc-card: Add storage for PCI SSID

[ Upstream commit 47f56e38a199bd45514b8e0142399cba4feeaf1a ]

Add members to struct snd_soc_card to store the PCI subsystem ID (SSID)
of the soundcard.

The PCI specification provides two registers to store a vendor-specific
SSID that can be read by drivers to uniquely identify a particular
"soundcard". This is defined in the PCI specification to distinguish
products that use the same silicon (and therefore have the same silicon
ID) so that product-specific differences can be applied.

PCI only defines 0xFFFF as an invalid value. 0x0000 is not defined as
invalid. So the usual pattern of zero-filling the struct and then
assuming a zero value unset will not work. A flag is included to
indicate when the SSID information has been filled in.

Unlike DMI information, which has a free-format entirely up to the vendor,
the PCI SSID has a strictly defined format and a registry of vendor IDs.

It is usual in Windows drivers that the SSID is used as the sole identifier
of the specific end-product and the Windows driver contains tables mapping
that to information about the hardware setup, rather than using ACPI
properties.

This SSID is important information for ASoC components that need to apply
hardware-specific configuration on PCI-based systems.

As the SSID is a generic part of the PCI specification and is treated as
identifying the "soundcard", it is reasonable to include this information
in struct snd_soc_card, instead of components inventing their own custom
ways to pass this information around.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230912163207.3498161-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: mediatek: mt8188-mt6359: support dynamic pinctrl

[ Upstream commit d601bb78f06b9e3cbb52e6b87b88add9920a11b6 ]

To avoid power leakage, it is recommended to replace the default pinctrl
state with dynamic pinctrl since certain audio pinmux functions can
remain in a HIGH state even when audio is disabled. Linking pinctrl with
DAPM using SND_SOC_DAPM_PINCTRL will ensure that audio pins remain in
GPIO mode by default and only switch to an audio function when necessary.

Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230825024935.10878-2-trevor.wu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests/efivarfs: create-read: fix a resource leak

[ Upstream commit 3f6f8a8c5e11a9b384a36df4f40f0c9a653b6975 ]

The opened file should be closed in main(), otherwise resource
leak will occur that this problem was discovered by code reading

Signed-off-by: zhujun2 <zhujun2@cmss.chinamobile.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: ls208xa: use a pseudo-bus to constrain usb dma size

[ Upstream commit b39d5016456871a88f5cd141914a5043591b46f3 ]

Wrap the usb controllers in an intermediate simple-bus and use it to
constrain the dma address size of these usb controllers to the 40b
that they generate toward the interconnect. This is required because
the SoC uses 48b address sizes and this mismatch would lead to smmu
context faults [1] because the usb generates 40b addresses while the
smmu page tables are populated with 48b wide addresses.

[1]
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f66d hci version 0x100 quirks 0x0000000002000010
xhci-hcd xhci-hcd.0.auto: irq 108, io mem 0x03100000
xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xffffffb000, fsynr=0x0, cbfrsynra=0xc01, cb=3

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: rockchip: Add NanoPC T6 PCIe e-key support

[ Upstream commit ac76b786cc370b000c76f3115a5d2ee76ff05c08 ]

before
~~~~
0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0002:20:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0002:21:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)
0004:40:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0004:41:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)

after
~~~
0000:00:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0002:20:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0002:21:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)
0003:30:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0003:31:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8822CE 802.11ac PCIe Wireless Network Adapter
0004:40:00.0 PCI bridge: Rockchip Electronics Co., Ltd RK3588 (rev 01)
0004:41:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)

Signed-off-by: John Clark <inindev@gmail.com>
Link: https://lore.kernel.org/r/20230906012305.7113-1-inindev@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

soc: qcom: pmic: Fix resource leaks in a device_for_each_child_node() loop

[ Upstream commit 5692aeea5bcb9331e956628c3bc8fc9afcc9765d ]

The device_for_each_child_node loop should call fwnode_handle_put()
before return in the error cases, to avoid resource leaks.

Let's fix this bug in pmic_glink_altmode_probe().

Signed-off-by: Lu Hongfei <luhongfei@vivo.com>
Link: https://lore.kernel.org/r/20230612133452.47315-1-luhongfei@vivo.com
[bjorn: Rebased patch, moved fw_handle_put() from jump target into the loop]
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd: check num of link levels when update pcie param

[ Upstream commit 406e8845356d18bdf3d3a23b347faf67706472ec ]

In SR-IOV environment, the value of pcie_table->num_of_link_levels will
be 0, and num_of_levels - 1 will cause array index out of bounds

Signed-off-by: Lin.Cao <lincao12@amd.com>
Acked-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: fix num_ways overflow error

[ Upstream commit 79f3f1b66753b3a3a269d73676bf50987921f267 ]

[Why]
Helper function calculates num_ways using 32-bit.  But is
 returned as 8-bit.  If num_ways exceeds 8-bit, then it
 reports back the incorrect num_ways and erroneously
 uses MALL when it should not

[How]
Make returned value 32-bit and convert after it checks
 against caps.cache_num_ways, which is under 8-bit

Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd: Disable PP_PCIE_DPM_MASK when dynamic speed switching not supported

[ Upstream commit fbf1035b033a51eee48d5f42e781b02fff272ca0 ]

Rather than individual ASICs checking for the quirk, set the quirk at the
driver level.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Fix a null pointer access when the smc_rreg pointer is NULL

[ Upstream commit 5104fdf50d326db2c1a994f8b35dcd46e63ae4ad ]

In certain types of chips, such as VEGA20, reading the amdgpu_regs_smc file could result in an abnormal null pointer access when the smc_rreg pointer is NULL. Below are the steps to reproduce this issue and the corresponding exception log:

1. Navigate to the directory: /sys/kernel/debug/dri/0
2. Execute command: cat amdgpu_regs_smc
3. Exception Log::
[4005007.702554] BUG: kernel NULL pointer dereference, address: 0000000000000000
[4005007.702562] #PF: supervisor instruction fetch in kernel mode
[4005007.702567] #PF: error_code(0x0010) - not-present page
[4005007.702570] PGD 0 P4D 0
[4005007.702576] Oops: 0010 [#1] SMP NOPTI
[4005007.702581] CPU: 4 PID: 62563 Comm: cat Tainted: G           OE     5.15.0-43-generic #46-Ubunt       u
[4005007.702590] RIP: 0010:0x0
[4005007.702598] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6.
[4005007.702600] RSP: 0018:ffffa82b46d27da0 EFLAGS: 00010206
[4005007.702605] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffa82b46d27e68
[4005007.702609] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff9940656e0000
[4005007.702612] RBP: ffffa82b46d27dd8 R08: 0000000000000000 R09: ffff994060c07980
[4005007.702615] R10: 0000000000020000 R11: 0000000000000000 R12: 00007f5e06753000
[4005007.702618] R13: ffff9940656e0000 R14: ffffa82b46d27e68 R15: 00007f5e06753000
[4005007.702622] FS:  00007f5e0755b740(0000) GS:ffff99479d300000(0000) knlGS:0000000000000000
[4005007.702626] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[4005007.702629] CR2: ffffffffffffffd6 CR3: 00000003253fc000 CR4: 00000000003506e0
[4005007.702633] Call Trace:
[4005007.702636]  <TASK>
[4005007.702640]  amdgpu_debugfs_regs_smc_read+0xb0/0x120 [amdgpu]
[4005007.703002]  full_proxy_read+0x5c/0x80
[4005007.703011]  vfs_read+0x9f/0x1a0
[4005007.703019]  ksys_read+0x67/0xe0
[4005007.703023]  __x64_sys_read+0x19/0x20
[4005007.703028]  do_syscall_64+0x5c/0xc0
[4005007.703034]  ? do_user_addr_fault+0x1e3/0x670
[4005007.703040]  ? exit_to_user_mode_prepare+0x37/0xb0
[4005007.703047]  ? irqentry_exit_to_user_mode+0x9/0x20
[4005007.703052]  ? irqentry_exit+0x19/0x30
[4005007.703057]  ? exc_page_fault+0x89/0x160
[4005007.703062]  ? asm_exc_page_fault+0x8/0x30
[4005007.703068]  entry_SYSCALL_64_after_hwframe+0x44/0xae
[4005007.703075] RIP: 0033:0x7f5e07672992
[4005007.703079] Code: c0 e9 b2 fe ff ff 50 48 8d 3d fa b2 0c 00 e8 c5 1d 02 00 0f 1f 44 00 00 f3 0f        1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 0f 05 <48> 3d 00 f0 ff ff 77 56 c3 0f 1f 44 00 00 48 83 e       c 28 48 89 54 24
[4005007.703083] RSP: 002b:00007ffe03097898 EFLAGS: 00000246 ORIG_RAX: 0000000000000000
[4005007.703088] RAX: ffffffffffffffda RBX: 0000000000020000 RCX: 00007f5e07672992
[4005007.703091] RDX: 0000000000020000 RSI: 00007f5e06753000 RDI: 0000000000000003
[4005007.703094] RBP: 00007f5e06753000 R08: 00007f5e06752010 R09: 00007f5e06752010
[4005007.703096] R10: 0000000000000022 R11: 0000000000000246 R12: 0000000000022000
[4005007.703099] R13: 0000000000000003 R14: 0000000000020000 R15: 0000000000020000
[4005007.703105]  </TASK>
[4005007.703107] Modules linked in: nf_tables libcrc32c nfnetlink algif_hash af_alg binfmt_misc nls_       iso8859_1 ipmi_ssif ast intel_rapl_msr intel_rapl_common drm_vram_helper drm_ttm_helper amd64_edac t       tm edac_mce_amd kvm_amd ccp mac_hid k10temp kvm acpi_ipmi ipmi_si rapl sch_fq_codel ipmi_devintf ipm       i_msghandler msr parport_pc ppdev lp parport mtd pstore_blk efi_pstore ramoops pstore_zone reed_solo       mon ip_tables x_tables autofs4 ib_uverbs ib_core amdgpu(OE) amddrm_ttm_helper(OE) amdttm(OE) iommu_v       2 amd_sched(OE) amdkcl(OE) drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core        drm igb ahci xhci_pci libahci i2c_piix4 i2c_algo_bit xhci_pci_renesas dca
[4005007.703184] CR2: 0000000000000000
[4005007.703188] ---[ end trace ac65a538d240da39 ]---
[4005007.800865] RIP: 0010:0x0
[4005007.800871] Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6.
[4005007.800874] RSP: 0018:ffffa82b46d27da0 EFLAGS: 00010206
[4005007.800878] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffa82b46d27e68
[4005007.800881] RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff9940656e0000
[4005007.800883] RBP: ffffa82b46d27dd8 R08: 0000000000000000 R09: ffff994060c07980
[4005007.800886] R10: 0000000000020000 R11: 0000000000000000 R12: 00007f5e06753000
[4005007.800888] R13: ffff9940656e0000 R14: ffffa82b46d27e68 R15: 00007f5e06753000
[4005007.800891] FS:  00007f5e0755b740(0000) GS:ffff99479d300000(0000) knlGS:0000000000000000
[4005007.800895] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[4005007.800898] CR2: ffffffffffffffd6 CR3: 00000003253fc000 CR4: 00000000003506e0

Signed-off-by: Qu Huang <qu.huang@linux.dev>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: Fix shift out-of-bounds issue

[ Upstream commit 282c1d793076c2edac6c3db51b7e8ed2b41d60a5 ]

[  567.613292] shift exponent 255 is too large for 64-bit type 'long unsigned int'
[  567.614498] CPU: 5 PID: 238 Comm: kworker/5:1 Tainted: G           OE      6.2.0-34-generic #34~22.04.1-Ubuntu
[  567.614502] Hardware name: AMD Splinter/Splinter-RPL, BIOS WS43927N_871 09/25/2023
[  567.614504] Workqueue: events send_exception_work_handler [amdgpu]
[  567.614748] Call Trace:
[  567.614750]  <TASK>
[  567.614753]  dump_stack_lvl+0x48/0x70
[  567.614761]  dump_stack+0x10/0x20
[  567.614763]  __ubsan_handle_shift_out_of_bounds+0x156/0x310
[  567.614769]  ? srso_alias_return_thunk+0x5/0x7f
[  567.614773]  ? update_sd_lb_stats.constprop.0+0xf2/0x3c0
[  567.614780]  svm_range_split_by_granularity.cold+0x2b/0x34 [amdgpu]
[  567.615047]  ? srso_alias_return_thunk+0x5/0x7f
[  567.615052]  svm_migrate_to_ram+0x185/0x4d0 [amdgpu]
[  567.615286]  do_swap_page+0x7b6/0xa30
[  567.615291]  ? srso_alias_return_thunk+0x5/0x7f
[  567.615294]  ? __free_pages+0x119/0x130
[  567.615299]  handle_pte_fault+0x227/0x280
[  567.615303]  __handle_mm_fault+0x3c0/0x720
[  567.615311]  handle_mm_fault+0x119/0x330
[  567.615314]  ? lock_mm_and_find_vma+0x44/0x250
[  567.615318]  do_user_addr_fault+0x1a9/0x640
[  567.615323]  exc_page_fault+0x81/0x1b0
[  567.615328]  asm_exc_page_fault+0x27/0x30
[  567.615332] RIP: 0010:__get_user_8+0x1c/0x30

Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Suggested-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/panel: st7703: Pick different reset sequence

[ Upstream commit d12d635bb03c7cb4830acb641eb176ee9ff2aa89 ]

Switching to a different reset sequence, enabling IOVCC before enabling
VCC.

There also needs to be a delay after enabling the supplies and before
deasserting the reset. The datasheet specifies 1ms after the supplies
reach the required voltage. Use 10-20ms to also give the power supplies
some time to reach the required voltage, too.

This fixes intermittent panel initialization failures and screen
corruption during resume from sleep on panel xingbangda,xbd599 (e.g.
used in PinePhone).

Signed-off-by: Ondrej Jirman <megi@xff.cz>
Signed-off-by: Frank Oltmanns <frank@oltmanns.dev>
Reported-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Tested-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230211171748.36692-2-frank@oltmanns.dev
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu/vkms: fix a possible null pointer dereference

[ Upstream commit cd90511557fdfb394bb4ac4c3b539b007383914c ]

In amdgpu_vkms_conn_get_modes(), the return value of drm_cvt_mode()
is assigned to mode, which will lead to a NULL pointer dereference
on failure of drm_cvt_mode(). Add a check to avoid null pointer
dereference.

Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/radeon: fix a possible null pointer dereference

[ Upstream commit 2c1fe3c480f9e1deefd50d4b18be4a046011ee1f ]

In radeon_tv_get_modes(), the return value of drm_cvt_mode()
is assigned to mode, which will lead to a NULL pointer
dereference on failure of drm_cvt_mode(). Add a check to
avoid null point dereference.

Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/panel/panel-tpo-tpg110: fix a possible null pointer dereference

[ Upstream commit f22def5970c423ea7f87d5247bd0ef91416b0658 ]

In tpg110_get_modes(), the return value of drm_mode_duplicate() is
assigned to mode, which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate(). Add a check to avoid npd.

Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231009090446.4043798-1-make_ruc2021@163.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231009090446.4043798-1-make_ruc2021@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/panel: fix a possible null pointer dereference

[ Upstream commit 924e5814d1f84e6fa5cb19c6eceb69f066225229 ]

In versatile_panel_get_modes(), the return value of drm_mode_duplicate()
is assigned to mode, which will lead to a NULL pointer dereference
on failure of drm_mode_duplicate(). Add a check to avoid npd.

Signed-off-by: Ma Ke <make_ruc2021@163.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231007033105.3997998-1-make_ruc2021@163.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20231007033105.3997998-1-make_ruc2021@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Fix potential null pointer derefernce

[ Upstream commit 80285ae1ec8717b597b20de38866c29d84d321a1 ]

The amdgpu_ras_get_context may return NULL if device
not support ras feature, so add check before using.

Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd: Fix UBSAN array-index-out-of-bounds for Polaris and Tonga

[ Upstream commit 0f0e59075b5c22f1e871fbd508d6e4f495048356 ]

For pptable structs that use flexible array sizes, use flexible arrays.

Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2036742
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd: Fix UBSAN array-index-out-of-bounds for SMU7

[ Upstream commit 760efbca74a405dc439a013a5efaa9fadc95a8c3 ]

For pptable structs that use flexible array sizes, use flexible arrays.

Suggested-by: Felix Held <felix.held@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2874
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/dp: skip validity check for DP CTS EDID checksum

[ Upstream commit a251c9d8e30833b260101edb9383b176ee2b7cb1 ]

The DP CTS test for EDID last block checksum expects the checksum for
the last block, invalid or not. Skip the validity check.

For the most part (*), the EDIDs returned by drm_get_edid() will be
valid anyway, and there's the CTS workaround to get the checksum for
completely invalid EDIDs. See commit 7948fe12d47a ("drm/msm/dp: return
correct edid checksum after corrupted edid checksum read").

This lets us remove one user of drm_edid_block_valid() with hopes the
function can be removed altogether in the future.

(*) drm_get_edid() ignores checksum errors on CTA extensions.

Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Kuogee Hsieh <khsieh@codeaurora.org>
Cc: Marijn Suijten <marijn.suijten@somainline.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/555361/
Link: https://lore.kernel.org/r/20230901142034.580802-1-jani.nikula@intel.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm: vmwgfx_surface.c: copy user-array safely

[ Upstream commit 06ab64a0d836ac430c5f94669710a78aa43942cb ]

Currently, there is no overflow-check with memdup_user().

Use the new function memdup_array_user() instead of memdup_user() for
duplicating the user-space array safely.

Suggested-by: David Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920123612.16914-7-pstanner@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm_lease.c: copy user-array safely

[ Upstream commit f37d63e219c39199a59b8b8a211412ff27192830 ]

Currently, there is no overflow-check with memdup_user().

Use the new function memdup_array_user() instead of memdup_user() for
duplicating the user-space array safely.

Suggested-by: David Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920123612.16914-6-pstanner@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel: watch_queue: copy user-array safely

[ Upstream commit ca0776571d3163bd03b3e8c9e3da936abfaecbf6 ]

Currently, there is no overflow-check with memdup_user().

Use the new function memdup_array_user() instead of memdup_user() for
duplicating the user-space array safely.

Suggested-by: David Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920123612.16914-5-pstanner@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

kernel: kexec: copy user-array safely

[ Upstream commit 569c8d82f95eb5993c84fb61a649a9c4ddd208b3 ]

Currently, there is no overflow-check with memdup_user().

Use the new function memdup_array_user() instead of memdup_user() for
duplicating the user-space array safely.

Suggested-by: David Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Acked-by: Baoquan He <bhe@redhat.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920123612.16914-4-pstanner@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

string.h: add array-wrappers for (v)memdup_user()

[ Upstream commit 313ebe47d75558511aa1237b6e35c663b5c0ec6f ]

Currently, user array duplications are sometimes done without an
overflow check. Sometimes the checks are done manually; sometimes the
array size is calculated with array_size() and sometimes by calculating
n * size directly in code.

Introduce wrappers for arrays for memdup_user() and vmemdup_user() to
provide a standardized and safe way for duplicating user arrays.

This is both for new code as well as replacing usage of (v)memdup_user()
in existing code that uses, e.g., n * size to calculate array sizes.

Suggested-by: David Airlie <airlied@redhat.com>
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920123612.16914-3-pstanner@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: use full update for clip size increase of large plane source

[ Upstream commit 05b78277ef0efc1deebc8a22384fffec29a3676e ]

[why]
Clip size increase will increase viewport, which could cause us to
switch  to MPC combine.
If we skip full update, we are not able to change to MPC combine in
fast update. This will cause corruption showing on the video plane.

[how]
treat clip size increase of a surface larger than 5k as a full update.

Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd: Update `update_pcie_parameters` functions to use uint8_t arguments

[ Upstream commit 7752ccf85b929a22e658ec145283e8f31232f4bb ]

The matching values for `pcie_gen_cap` and `pcie_width_cap` when
fetched from powerplay tables are 1 byte, so narrow the arguments
to match to ensure min() and max() comparisons without casts.

Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: update retry times for psp vmbx wait

[ Upstream commit fc598890715669ff794b253fdf387cd02b9396f8 ]

Increase the retry loops and replace the constant number with macro.

Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: Fix a race condition of vram buffer unref in svm code

[ Upstream commit 709c348261618da7ed89d6c303e2ceb9e453ba74 ]

prange->svm_bo unref can happen in both mmu callback and a callback after
migrate to system ram. Both are async call in different tasks. Sync svm_bo
unref operation to avoid random "use-after-free".

Signed-off-by: Xiaogang Chen <xiaogang.chen@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Jesse Zhang <Jesse.Zhang@amd.com>
Tested-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: not to save bo in the case of RAS err_event_athub

[ Upstream commit fa1f1cc09d588a90c8ce3f507c47df257461d148 ]

err_event_athub will corrupt VCPU buffer and not good to
be restored in amdgpu_vcn_resume() and in this case
the VCPU buffer needs to be cleared for VCN firmware to
work properly.

Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

md: don't rely on 'mddev->pers' to be set in mddev_suspend()

[ Upstream commit b721e7885eb242aa2459ee66bb42ceef1bcf0f0c ]

'active_io' used to be initialized while the array is running, and
'mddev->pers' is set while the array is running as well. Hence caller
must hold 'reconfig_mutex' and guarantee 'mddev->pers' is set before
calling mddev_suspend().

Now that 'active_io' is initialized when mddev is allocated, such
restriction doesn't exist anymore. In the meantime, follow up patches
will refactor mddev_suspend(), hence add checking for 'mddev->pers' to
prevent null-ptr-deref.

Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20230825030956.1527023-4-yukuai1@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/edid: Fixup h/vsync_end instead of h/vtotal

[ Upstream commit 2682768bde745b10ae126a322cdcaf532cf88851 ]

There are some weird EDIDs floating around that have the sync
pulse extending beyond the end of the blanking period.

On the currently problemtic machine (HP Omni 120) EDID reports
the following mode:
"1600x900": 60 108000 1600 1780 1860 1800 900 910 913 1000 0x40 0x5
which is then "corrected" to have htotal=1861 by the current drm_edid.c
code.

The fixup code was originally added in commit 7064fef56369 ("drm: work
around EDIDs with bad htotal/vtotal values"). Googling around we end up in
https://bugs.launchpad.net/ubuntu/hardy/+source/xserver-xorg-video-intel/+bug/297245
where we find an EDID for a Dell Studio 15, which reports:
(II) VESA(0): clock: 65.0 MHz   Image Size:  331 x 207 mm
(II) VESA(0): h_active: 1280  h_sync: 1328  h_sync_end 1360 h_blank_end 1337 h_border: 0
(II) VESA(0): v_active: 800  v_sync: 803  v_sync_end 809 v_blanking: 810 v_border: 0

Note that if we use the hblank size (as opposed of the hsync_end)
from the DTD to determine htotal we get exactly 60Hz refresh rate in
both cases, whereas using hsync_end to determine htotal we get a
slightly lower refresh rates. This makes me believe the using the
hblank size is what was intended even in those cases.

Also note that in case of the HP Onmi 120 the VBIOS boots with these:
  crtc timings: 108000 1600 1780 1860 1800 900 910 913 1000, type: 0x40 flags: 0x5
ie. it just blindly stuffs the bogus hsync_end and htotal from the DTD
into the transcoder timing registers, and the display works. I believe
the (at least more modern) hardware will automagically terminate the hsync
pulse when the timing generator reaches htotal, which again points that we
should use the hblank size to determine htotal. Unfortunatley the old bug
reports for the Dell machines are extremely lacking in useful details so
we have no idea what kind of timings the VBIOS programmed into the
hardware :(

Let's just flip this quirk around and reduce the length of the sync
pulse instead of extending the blanking period. This at least seems
to be the correct thing to do on more modern hardware. And if any
issues crop up on older hardware we need to debug them properly.

v2: Add debug message breadcrumbs (Jani)

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8895
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230920211934.14920-1-ville.syrjala@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: add seamless pipe topology transition check

[ Upstream commit 15c6798ae26d5c7a7776f4f7d0c1fa8c462688a2 ]

[why]
We have a few cases where we need to perform update topology update
in dc update interface. However some of the updates are not seamless
This could cause user noticible glitches. To enforce seamless transition
we are adding a checking condition and error logging so the corruption
as result of non seamless transition can be easily spotted.

Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Don't lock phantom pipe on disabling

[ Upstream commit cbb4c9bc55427774ca4d819933e1b5fa38a6fb44 ]

[Description]
- When disabling a phantom pipe, we first enable the phantom
  OTG so the double buffer update can successfully take place
- However, want to avoid locking the phantom otherwise setting
  DPG_EN=1 for the phantom pipe is blocked (without this we could
  hit underflow due to phantom HUBP being blanked by default)

Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Blank phantom OTG before enabling

[ Upstream commit e87a6c5b7780b5f423797351eb586ed96cc6d151 ]

[Description]
Before enabling the phantom OTG for an update we
must enable DPG to avoid underflow.

Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/komeda: drop all currently held locks if deadlock happens

[ Upstream commit 19ecbe8325a2a7ffda5ff4790955b84eaccba49f ]

If komeda_pipeline_unbound_components() returns -EDEADLK,
it means that a deadlock happened in the locking context.
Currently, komeda is not dealing with the deadlock properly,producing the
following output when CONFIG_DEBUG_WW_MUTEX_SLOWPATH is enabled:

 ------------[ cut here ]------------
[   26.103984] WARNING: CPU: 2 PID: 345 at drivers/gpu/drm/arm/display/komeda/komeda_pipeline_state.c:1248
       komeda_release_unclaimed_resources+0x13c/0x170
[   26.117453] Modules linked in:
[   26.120511] CPU: 2 PID: 345 Comm: composer@2.1-se Kdump: loaded Tainted: G   W  5.10.110-SE-SDK1.8-dirty #16
[   26.131374] Hardware name: Siengine Se1000 Evaluation board (DT)
[   26.137379] pstate: 20400009 (nzCv daif +PAN -UAO -TCO BTYPE=--)
[   26.143385] pc : komeda_release_unclaimed_resources+0x13c/0x170
[   26.149301] lr : komeda_release_unclaimed_resources+0xbc/0x170
[   26.155130] sp : ffff800017b8b8d0
[   26.158442] pmr_save: 000000e0
[   26.161493] x29: ffff800017b8b8d0 x28: ffff000cf2f96200
[   26.166805] x27: ffff000c8f5a8800 x26: 0000000000000000
[   26.172116] x25: 0000000000000038 x24: ffff8000116a0140
[   26.177428] x23: 0000000000000038 x22: ffff000cf2f96200
[   26.182739] x21: ffff000cfc300300 x20: ffff000c8ab77080
[   26.188051] x19: 0000000000000003 x18: 0000000000000000
[   26.193362] x17: 0000000000000000 x16: 0000000000000000
[   26.198672] x15: b400e638f738ba38 x14: 0000000000000000
[   26.203983] x13: 0000000106400a00 x12: 0000000000000000
[   26.209294] x11: 0000000000000000 x10: 0000000000000000
[   26.214604] x9 : ffff800012f80000 x8 : ffff000ca3308000
[   26.219915] x7 : 0000000ff3000000 x6 : ffff80001084034c
[   26.225226] x5 : ffff800017b8bc40 x4 : 000000000000000f
[   26.230536] x3 : ffff000ca3308000 x2 : 0000000000000000
[   26.235847] x1 : 0000000000000000 x0 : ffffffffffffffdd
[   26.241158] Call trace:
[   26.243604] komeda_release_unclaimed_resources+0x13c/0x170
[   26.249175] komeda_crtc_atomic_check+0x68/0xf0
[   26.253706] drm_atomic_helper_check_planes+0x138/0x1f4
[   26.258929] komeda_kms_check+0x284/0x36c
[   26.262939] drm_atomic_check_only+0x40c/0x714
[   26.267381] drm_atomic_nonblocking_commit+0x1c/0x60
[   26.272344] drm_mode_atomic_ioctl+0xa3c/0xb8c
[   26.276787] drm_ioctl_kernel+0xc4/0x120
[   26.280708] drm_ioctl+0x268/0x534
[   26.284109] __arm64_sys_ioctl+0xa8/0xf0
[   26.288030] el0_svc_common.constprop.0+0x80/0x240
[   26.292817] do_el0_svc+0x24/0x90
[   26.296132] el0_svc+0x20/0x30
[   26.299185] el0_sync_handler+0xe8/0xf0
[   26.303018] el0_sync+0x1a4/0x1c0
[   26.306330] irq event stamp: 0
[   26.309384] hardirqs last  enabled at (0): [<0000000000000000>] 0x0
[   26.315650] hardirqs last disabled at (0): [<ffff800010056d34>] copy_process+0x5d0/0x183c
[   26.323825] softirqs last  enabled at (0): [<ffff800010056d34>] copy_process+0x5d0/0x183c
[   26.331997] softirqs last disabled at (0): [<0000000000000000>] 0x0
[   26.338261] ---[ end trace 20ae984fa860184a ]---
[   26.343021] ------------[ cut here ]------------
[   26.347646] WARNING: CPU: 3 PID: 345 at drivers/gpu/drm/drm_modeset_lock.c:228 drm_modeset_drop_locks+0x84/0x90
[   26.357727] Modules linked in:
[   26.360783] CPU: 3 PID: 345 Comm: composer@2.1-se Kdump: loaded Tainted: G   W  5.10.110-SE-SDK1.8-dirty #16
[   26.371645] Hardware name: Siengine Se1000 Evaluation board (DT)
[   26.377647] pstate: 20400009 (nzCv daif +PAN -UAO -TCO BTYPE=--)
[   26.383649] pc : drm_modeset_drop_locks+0x84/0x90
[   26.388351] lr : drm_mode_atomic_ioctl+0x860/0xb8c
[   26.393137] sp : ffff800017b8bb10
[   26.396447] pmr_save: 000000e0
[   26.399497] x29: ffff800017b8bb10 x28: 0000000000000001
[   26.404807] x27: 0000000000000038 x26: 0000000000000002
[   26.410115] x25: ffff000cecbefa00 x24: ffff000cf2f96200
[   26.415423] x23: 0000000000000001 x22: 0000000000000018
[   26.420731] x21: 0000000000000001 x20: ffff800017b8bc10
[   26.426039] x19: 0000000000000000 x18: 0000000000000000
[   26.431347] x17: 0000000002e8bf2c x16: 0000000002e94c6b
[   26.436655] x15: 0000000002ea48b9 x14: ffff8000121f0300
[   26.441963] x13: 0000000002ee2ca8 x12: ffff80001129cae0
[   26.447272] x11: ffff800012435000 x10: ffff000ed46b5e88
[   26.452580] x9 : ffff000c9935e600 x8 : 0000000000000000
[   26.457888] x7 : 000000008020001e x6 : 000000008020001f
[   26.463196] x5 : ffff80001085fbe0 x4 : fffffe0033a59f20
[   26.468504] x3 : 000000008020001e x2 : 0000000000000000
[   26.473813] x1 : 0000000000000000 x0 : ffff000c8f596090
[   26.479122] Call trace:
[   26.481566] drm_modeset_drop_locks+0x84/0x90
[   26.485918] drm_mode_atomic_ioctl+0x860/0xb8c
[   26.490359] drm_ioctl_kernel+0xc4/0x120
[   26.494278] drm_ioctl+0x268/0x534
[   26.497677] __arm64_sys_ioctl+0xa8/0xf0
[   26.501598] el0_svc_common.constprop.0+0x80/0x240
[   26.506384] do_el0_svc+0x24/0x90
[   26.509697] el0_svc+0x20/0x30
[   26.512748] el0_sync_handler+0xe8/0xf0
[   26.516580] el0_sync+0x1a4/0x1c0
[   26.519891] irq event stamp: 0
[   26.522943] hardirqs last  enabled at (0): [<0000000000000000>] 0x0
[   26.529207] hardirqs last disabled at (0): [<ffff800010056d34>] copy_process+0x5d0/0x183c
[   26.537379] softirqs last  enabled at (0): [<ffff800010056d34>] copy_process+0x5d0/0x183c
[   26.545550] softirqs last disabled at (0): [<0000000000000000>] 0x0
[   26.551812] ---[ end trace 20ae984fa860184b ]---

According to the call trace information,it can be located to be
WARN_ON(IS_ERR(c_st)) in the komeda_pipeline_unbound_components function;
Then follow the function.
komeda_pipeline_unbound_components
-> komeda_component_get_state_and_set_user
  -> komeda_pipeline_get_state_and_set_crtc
    -> komeda_pipeline_get_state
      ->drm_atomic_get_private_obj_state
        -> drm_atomic_get_private_obj_state
          -> drm_modeset_lock

komeda_pipeline_unbound_components
-> komeda_component_get_state_and_set_user
  -> komeda_component_get_state
    -> drm_atomic_get_private_obj_state
     -> drm_modeset_lock

ret = drm_modeset_lock(&obj->lock, state->acquire_ctx); if (ret)
return ERR_PTR(ret);
Here it return -EDEADLK.

deal with the deadlock as suggested by [1], using the
function drm_modeset_backoff().
[1] https://docs.kernel.org/gpu/drm-kms.html?highlight=kms#kms-locking

Therefore, handling this problem can be solved
by adding return -EDEADLK back to the drm_modeset_backoff processing flow
in the drm_mode_atomic_ioctl function.

Signed-off-by: baozhu.liu <lucas.liu@siengine.com>
Signed-off-by: menghui.huang <menghui.huang@siengine.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230804013117.6870-1-menghui.huang@siengine.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdkfd: ratelimited SQ interrupt messages

[ Upstream commit 37fb87910724f21a1f27a75743d4f9accdee77fb ]

No functional change. Use ratelimited version of pr_ to avoid
overflowing of dmesg buffer

Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Philip Yang <philip.yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/gma500: Fix call trace when psb_gem_mm_init() fails

[ Upstream commit da596080b2b400c50fe9f8f237bcaf09fed06af8 ]

Because the gma_irq_install() is call after psb_gem_mm_init() function,
when psb_gem_mm_init() fails, the interrupt line haven't been allocated.
Yet the gma_irq_uninstall() is called in the psb_driver_unload() function
without checking if checking the irq is registered or not.

The calltrace is appended as following:

[   20.539253] ioremap memtype_reserve failed -16
[   20.543895] gma500 0000:00:02.0: Failure to map stolen base.
[   20.565049] ------------[ cut here ]------------
[   20.565066] Trying to free already-free IRQ 16
[   20.565087] WARNING: CPU: 1 PID: 381 at kernel/irq/manage.c:1893 free_irq+0x209/0x370
[   20.565316] CPU: 1 PID: 381 Comm: systemd-udevd Tainted: G         C         6.5.0-rc1+ #368
[   20.565329] Hardware name: To Be Filled By O.E.M. To Be Filled By O.E.M./IMB-140D Plus, BIOS P1.10 11/18/2013
[   20.565338] RIP: 0010:free_irq+0x209/0x370
[   20.565357] Code: 41 5d 41 5e 41 5f 5d 31 d2 89 d1 89 d6 89 d7 41 89 d1 c3 cc cc cc cc 8b 75 d0 48 c7 c7 e0 77 12 9f 4c 89 4d c8 e8 57 fe f4 ff <0f> 0b 48 8b 75 c8 4c 89 f7 e8 29 f3 f1 00 49 8b 47 40 48 8b 40 78
[   20.565369] RSP: 0018:ffffae3b40733808 EFLAGS: 00010046
[   20.565382] RAX: 0000000000000000 RBX: ffff9f8082bfe000 RCX: 0000000000000000
[   20.565390] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[   20.565397] RBP: ffffae3b40733840 R08: 0000000000000000 R09: 0000000000000000
[   20.565405] R10: 0000000000000000 R11: 0000000000000000 R12: ffff9f80871c3100
[   20.565413] R13: ffff9f80835d3360 R14: ffff9f80835d32a4 R15: ffff9f80835d3200
[   20.565424] FS:  00007f13d36458c0(0000) GS:ffff9f8138880000(0000) knlGS:0000000000000000
[   20.565434] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   20.565441] CR2: 00007f0d046f3f20 CR3: 0000000006c8c000 CR4: 00000000000006e0
[   20.565450] Call Trace:
[   20.565458]  <TASK>
[   20.565470]  ? show_regs+0x72/0x90
[   20.565488]  ? free_irq+0x209/0x370
[   20.565504]  ? __warn+0x8d/0x160
[   20.565520]  ? free_irq+0x209/0x370
[   20.565536]  ? report_bug+0x1bb/0x1d0
[   20.565555]  ? handle_bug+0x46/0x90
[   20.565572]  ? exc_invalid_op+0x19/0x80
[   20.565587]  ? asm_exc_invalid_op+0x1b/0x20
[   20.565607]  ? free_irq+0x209/0x370
[   20.565625]  ? free_irq+0x209/0x370
[   20.565644]  gma_irq_uninstall+0x15b/0x1e0 [gma500_gfx]
[   20.565728]  psb_driver_unload+0x27/0x190 [gma500_gfx]
[   20.565800]  psb_pci_probe+0x5d2/0x790 [gma500_gfx]
[   20.565873]  local_pci_probe+0x48/0xb0
[   20.565892]  pci_device_probe+0xc8/0x280
[   20.565912]  really_probe+0x1d2/0x440
[   20.565929]  __driver_probe_device+0x8a/0x190
[   20.565944]  driver_probe_device+0x23/0xd0
[   20.565957]  __driver_attach+0x10f/0x220
[   20.565971]  ? __pfx___driver_attach+0x10/0x10
[   20.565984]  bus_for_each_dev+0x7a/0xe0
[   20.566002]  driver_attach+0x1e/0x30
[   20.566014]  bus_add_driver+0x127/0x240
[   20.566029]  driver_register+0x64/0x140
[   20.566043]  ? __pfx_psb_init+0x10/0x10 [gma500_gfx]
[   20.566111]  __pci_register_driver+0x68/0x80
[   20.566128]  psb_init+0x2c/0xff0 [gma500_gfx]
[   20.566194]  do_one_initcall+0x46/0x330
[   20.566214]  ? kmalloc_trace+0x2a/0xb0
[   20.566233]  do_init_module+0x6a/0x270
[   20.566250]  load_module+0x207f/0x23a0
[   20.566278]  init_module_from_file+0x9c/0xf0
[   20.566293]  ? init_module_from_file+0x9c/0xf0
[   20.566315]  idempotent_init_module+0x184/0x240
[   20.566335]  __x64_sys_finit_module+0x64/0xd0
[   20.566352]  do_syscall_64+0x59/0x90
[   20.566366]  ? ksys_mmap_pgoff+0x123/0x270
[   20.566378]  ? __secure_computing+0x9b/0x110
[   20.566392]  ? exit_to_user_mode_prepare+0x39/0x190
[   20.566406]  ? syscall_exit_to_user_mode+0x2a/0x50
[   20.566420]  ? do_syscall_64+0x69/0x90
[   20.566433]  ? do_syscall_64+0x69/0x90
[   20.566445]  ? do_syscall_64+0x69/0x90
[   20.566458]  entry_SYSCALL_64_after_hwframe+0x6e/0xd8
[   20.566472] RIP: 0033:0x7f13d351ea3d
[   20.566485] Code: 5b 41 5c c3 66 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d c3 a3 0f 00 f7 d8 64 89 01 48
[   20.566496] RSP: 002b:00007ffe566c1fd8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[   20.566510] RAX: ffffffffffffffda RBX: 000055e66806eec0 RCX: 00007f13d351ea3d
[   20.566519] RDX: 0000000000000000 RSI: 00007f13d36d9441 RDI: 0000000000000010
[   20.566527] RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000002
[   20.566535] R10: 0000000000000010 R11: 0000000000000246 R12: 00007f13d36d9441
[   20.566543] R13: 000055e6681108c0 R14: 000055e66805ba70 R15: 000055e66819a9c0
[   20.566559]  </TASK>
[   20.566566] ---[ end trace 0000000000000000 ]---

Signed-off-by: Sui Jingfeng <suijingfeng@loongson.cn>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727185855.713318-1-suijingfeng@loongson.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: thinkpad_acpi: Add battery quirk for Thinkpad X120e

[ Upstream commit 916646758aea81a143ce89103910f715ed923346 ]

Thinkpad X120e also needs this battery quirk.

Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Link: https://lore.kernel.org/r/20231024190922.2742-1-olli.asikainen@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of: address: Fix address translation when address-size is greater than 2

[ Upstream commit 42604f8eb7ba04b589375049cc76282dad4677d2 ]

With the recent addition of of_pci_prop_ranges() in commit 407d1a51921e
("PCI: Create device tree node for bridge"), the ranges property can
have a 3 cells child address, a 3 cells parent address and a 2 cells
child size.

A range item property for a PCI device is filled as follow:
  <BAR_nbr> 0 0 <phys.hi> <phys.mid> <phys.low> <BAR_sizeh> <BAR_sizel>
  <-- Child --> <-- Parent (PCI definition) --> <- BAR size (64bit) -->

This allow to translate BAR addresses from the DT. For instance:
pci@0,0 {
  #address-cells = <0x03>;
  #size-cells = <0x02>;
  device_type = "pci";
  compatible = "pci11ab,100", "pciclass,060400", "pciclass,0604";
  ranges = <0x82000000 0x00 0xe8000000
            0x82000000 0x00 0xe8000000
    0x00 0x4400000>;
  ...
  dev@0,0 {
    #address-cells = <0x03>;
    #size-cells = <0x02>;
    compatible = "pci1055,9660", "pciclass,020000", "pciclass,0200";
    /* Translations for BAR0 to BAR5 */
    ranges = <0x00 0x00 0x00 0x82010000 0x00 0xe8000000 0x00 0x2000000
              0x01 0x00 0x00 0x82010000 0x00 0xea000000 0x00 0x1000000
              0x02 0x00 0x00 0x82010000 0x00 0xeb000000 0x00 0x800000
              0x03 0x00 0x00 0x82010000 0x00 0xeb800000 0x00 0x800000
              0x04 0x00 0x00 0x82010000 0x00 0xec000000 0x00 0x20000
              0x05 0x00 0x00 0x82010000 0x00 0xec020000 0x00 0x2000>;
    ...
    pci-ep-bus@0 {
      #address-cells = <0x01>;
      #size-cells = <0x01>;
      compatible = "simple-bus";
      /* Translate 0xe2000000 to BAR0 and 0xe0000000 to BAR1 */
      ranges = <0xe2000000 0x00 0x00 0x00 0x2000000
                0xe0000000 0x01 0x00 0x00 0x1000000>;
      ...
    };
  };
};

During the translation process, the "default-flags" map() function is
used to select the matching item in the ranges table and determine the
address offset from this matching item.
This map() function simply calls of_read_number() and when address-size
is greater than 2, the map() function skips the extra high address part
(ie part over 64bit). This lead to a wrong matching item and a wrong
offset computation.
Also during the translation itself, the extra high part related to the
parent address is not present in the translated address.

Fix the "default-flags" map() and translate() in order to take into
account the child extra high address part in map() and the parent extra
high address part in translate() and so having a correct address
translation for ranges patterns such as the one given in the example
above.

Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Link: https://lore.kernel.org/r/20231017110221.189299-2-herve.codina@bootlin.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/chrome: kunit: initialize lock for fake ec_dev

[ Upstream commit e410b4ade83d06a046f6e32b5085997502ba0559 ]

cros_ec_cmd_xfer() uses ec_dev->lock.  Initialize it.

Otherwise, dmesg shows the following:
> DEBUG_LOCKS_WARN_ON(lock->magic != lock)
> ...
> Call Trace:
>  ? __mutex_lock
>  ? __warn
>  ? __mutex_lock
>  ...
>  ? cros_ec_cmd_xfer

Reviewed-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/20231003080504.4011337-1-tzungbi@kernel.org
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: acpi: Add a ignore interrupt quirk for Peaq C1010

[ Upstream commit 6cc64f6173751d212c9833bde39e856b4f585a3e ]

On the Peaq C1010 2-in-1 INT33FC:00 pin 3 is connected to
a "dolby" button. At the ACPI level an _AEI event-handler
is connected which sets an ACPI variable to 1 on both
edges. This variable can be polled + cleared to 0 using WMI.

Since the variable is set on both edges the WMI interface is pretty
useless even when polling. So instead of writing a custom WMI
driver for this the x86-android-tablets code instantiates
a gpio-keys platform device for the "dolby" button.

Add an ignore_interrupt quirk for INT33FC:00 pin 3 on the Peaq C1010,
so that it is not seen as busy when the gpio-keys driver requests it.

Note this replaces a hack in x86-android-tablets where it would
call acpi_gpiochip_free_interrupts() on the INT33FC:00 GPIO
controller. acpi_gpiochip_free_interrupts() is considered private
(internal) gpiolib API so x86-android-tablets should stop using it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20230909141816.58358-3-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

tsnep: Fix tsnep_request_irq() format-overflow warning

[ Upstream commit 00e984cb986b31e9313745e51daceaa1e1eb7351 ]

Compiler warns about a possible format-overflow in tsnep_request_irq():
drivers/net/ethernet/engleder/tsnep_main.c:884:55: warning: 'sprintf' may write a terminating nul past the end of the destination [-Wformat-overflow=]
                         sprintf(queue->name, "%s-rx-%d", name,
                                                       ^
drivers/net/ethernet/engleder/tsnep_main.c:881:55: warning: 'sprintf' may write a terminating nul past the end of the destination [-Wformat-overflow=]
                         sprintf(queue->name, "%s-tx-%d", name,
                                                       ^
drivers/net/ethernet/engleder/tsnep_main.c:878:49: warning: '-txrx-' directive writing 6 bytes into a region of size between 5 and 25 [-Wformat-overflow=]
                         sprintf(queue->name, "%s-txrx-%d", name,
                                                 ^~~~~~

Actually overflow cannot happen. Name is limited to IFNAMSIZ, because
netdev_name() is called during ndo_open(). queue_index is single char,
because less than 10 queues are supported.

Fix warning with snprintf(). Additionally increase buffer to 32 bytes,
because those 7 additional bytes were unused anyway.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310182028.vmDthIUa-lkp@intel.com/
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231023183856.58373-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPI: EC: Add quirk for HP 250 G7 Notebook PC

[ Upstream commit 891ddc03e2f4395e24795596e032f57d5ab37fe7 ]

Add GPE quirk entry for HP 250 G7 Notebook PC.

This change allows the lid switch to be identified as the lid switch
and not a keyboard button. With the lid switch properly identified, the
device triggers suspend correctly on lid close.

Signed-off-by: Jonathan Denose <jdenose@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Fix double free in hci_conn_cleanup

[ Upstream commit a85fb91e3d728bdfc80833167e8162cce8bc7004 ]

syzbot reports a slab use-after-free in hci_conn_hash_flush [1].
After releasing an object using hci_conn_del_sysfs in the
hci_conn_cleanup function, releasing the same object again
using the hci_dev_put and hci_conn_put functions causes a double free.
Here's a simplified flow:

hci_conn_del_sysfs:
  hci_dev_put
    put_device
      kobject_put
        kref_put
          kobject_release
            kobject_cleanup
              kfree_const
                kfree(name)

hci_dev_put:
  ...
    kfree(name)

hci_conn_put:
  put_device
    ...
      kfree(name)

This patch drop the hci_dev_put and hci_conn_put function
call in hci_conn_cleanup function, because the object is
freed in hci_conn_del_sysfs function.

This patch also fixes the refcounting in hci_conn_add_sysfs() and
hci_conn_del_sysfs() to take into account device_add() failures.

This fixes CVE-2023-28464.

Link: https://syzkaller.appspot.com/bug?id=1bb51491ca5df96a5f724899d1dbb87afda61419
Signed-off-by: ZhengHan Wang <wzhmmmmm@gmail.com>
Co-developed-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: btusb: Add date->evt_skb is NULL check

[ Upstream commit 624820f7c8826dd010e8b1963303c145f99816e9 ]

fix crash because of null pointers

[ 6104.969662] BUG: kernel NULL pointer dereference, address: 00000000000000c8
[ 6104.969667] #PF: supervisor read access in kernel mode
[ 6104.969668] #PF: error_code(0x0000) - not-present page
[ 6104.969670] PGD 0 P4D 0
[ 6104.969673] Oops: 0000 [#1] SMP NOPTI
[ 6104.969684] RIP: 0010:btusb_mtk_hci_wmt_sync+0x144/0x220 [btusb]
[ 6104.969688] RSP: 0018:ffffb8d681533d48 EFLAGS: 00010246
[ 6104.969689] RAX: 0000000000000000 RBX: ffff8ad560bb2000 RCX: 0000000000000006
[ 6104.969691] RDX: 0000000000000000 RSI: ffffb8d681533d08 RDI: 0000000000000000
[ 6104.969692] RBP: ffffb8d681533d70 R08: 0000000000000001 R09: 0000000000000001
[ 6104.969694] R10: 0000000000000001 R11: 00000000fa83b2da R12: ffff8ad461d1d7c0
[ 6104.969695] R13: 0000000000000000 R14: ffff8ad459618c18 R15: ffffb8d681533d90
[ 6104.969697] FS:  00007f5a1cab9d40(0000) GS:ffff8ad578200000(0000) knlGS:00000
[ 6104.969699] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 6104.969700] CR2: 00000000000000c8 CR3: 000000018620c001 CR4: 0000000000760ef0
[ 6104.969701] PKRU: 55555554
[ 6104.969702] Call Trace:
[ 6104.969708]  btusb_mtk_shutdown+0x44/0x80 [btusb]
[ 6104.969732]  hci_dev_do_close+0x470/0x5c0 [bluetooth]
[ 6104.969748]  hci_rfkill_set_block+0x56/0xa0 [bluetooth]
[ 6104.969753]  rfkill_set_block+0x92/0x160
[ 6104.969755]  rfkill_fop_write+0x136/0x1e0
[ 6104.969759]  __vfs_write+0x18/0x40
[ 6104.969761]  vfs_write+0xdf/0x1c0
[ 6104.969763]  ksys_write+0xb1/0xe0
[ 6104.969765]  __x64_sys_write+0x1a/0x20
[ 6104.969769]  do_syscall_64+0x51/0x180
[ 6104.969771]  entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 6104.969773] RIP: 0033:0x7f5a21f18fef
[ 6104.9] RSP: 002b:00007ffeefe39010 EFLAGS: 00000293 ORIG_RAX: 0000000000000001
[ 6104.969780] RAX: ffffffffffffffda RBX: 000055c10a7560a0 RCX: 00007f5a21f18fef
[ 6104.969781] RDX: 0000000000000008 RSI: 00007ffeefe39060 RDI: 0000000000000012
[ 6104.969782] RBP: 00007ffeefe39060 R08: 0000000000000000 R09: 0000000000000017
[ 6104.969784] R10: 00007ffeefe38d97 R11: 0000000000000293 R12: 0000000000000002
[ 6104.969785] R13: 00007ffeefe39220 R14: 00007ffeefe391a0 R15: 000055c10a72acf0

Signed-off-by: youwan Wang <wangyouwan@126.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: iwlwifi: mvm: fix size check for fw_link_id

[ Upstream commit e25bd1853cc8308158d97e5b3696ea3689fa0840 ]

Check that fw_link_id does not exceed the size of link_id_to_link_conf
array. There's no any codepath that can cause that, but it's still
safer to verify in case fw_link_id gets corrupted.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231017115047.3385bd11f423.I2d30fdb464f951c648217553c47901857a0046c7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: Ensure proper register state printing for cond jumps

[ Upstream commit 1a8a315f008a58f54fecb012b928aa6a494435b3 ]

Verifier emits relevant register state involved in any given instruction
next to it after `;` to the right, if possible. Or, worst case, on the
separate line repeating instruction index.

E.g., a nice and simple case would be:

  2: (d5) if r0 s<= 0x0 goto pc+1       ; R0_w=0

But if there is some intervening extra output (e.g., precision
backtracking log) involved, we are supposed to see the state after the
precision backtrack log:

  4: (75) if r0 s>= 0x0 goto pc+1
  mark_precise: frame0: last_idx 4 first_idx 0 subseq_idx -1
  mark_precise: frame0: regs=r0 stack= before 2: (d5) if r0 s<= 0x0 goto pc+1
  mark_precise: frame0: regs=r0 stack= before 1: (b7) r0 = 0
  6: R0_w=0

First off, note that in `6: R0_w=0` instruction index corresponds to the
next instruction, not to the conditional jump instruction itself, which
is wrong and we'll get to that.

But besides that, the above is a happy case that does work today. Yet,
if it so happens that precision backtracking had to traverse some of the
parent states, this `6: R0_w=0` state output would be missing.

This is due to a quirk of print_verifier_state() routine, which performs
mark_verifier_state_clean(env) at the end. This marks all registers as
"non-scratched", which means that subsequent logic to print *relevant*
registers (that is, "scratched ones") fails and doesn't see anything
relevant to print and skips the output altogether.

print_verifier_state() is used both to print instruction context, but
also to print an **entire** verifier state indiscriminately, e.g.,
during precision backtracking (and in a few other situations, like
during entering or exiting subprogram).  Which means if we have to print
entire parent state before getting to printing instruction context
state, instruction context is marked as clean and is omitted.

Long story short, this is definitely not intentional. So we fix this
behavior in this patch by teaching print_verifier_state() to clear
scratch state only if it was used to print instruction state, not the
parent/callback state. This is determined by print_all option, so if
it's not set, we don't clear scratch state. This fixes missing
instruction state for these cases.

As for the mismatched instruction index, we fix that by making sure we
call print_insn_state() early inside check_cond_jmp_op() before we
adjusted insn_idx based on jump branch taken logic. And with that we get
desired correct information:

  9: (16) if w4 == 0x1 goto pc+9
  mark_precise: frame0: last_idx 9 first_idx 9 subseq_idx -1
  mark_precise: frame0: parent state regs=r4 stack=: R2_w=1944 R4_rw=P1 R10=fp0
  mark_precise: frame0: last_idx 8 first_idx 0 subseq_idx 9
  mark_precise: frame0: regs=r4 stack= before 8: (66) if w4 s> 0x3 goto pc+5
  mark_precise: frame0: regs=r4 stack= before 7: (b7) r4 = 1
  9: R4=1

Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Eduard Zingerman <eddyz87@gmail.com>
Link: https://lore.kernel.org/bpf/20231011223728.3188086-6-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

vsock: read from socket's error queue

[ Upstream commit 49dbe25adac42d3e06f65d1420946bec65896222 ]

This adds handling of MSG_ERRQUEUE input flag in receive call. This flag
is used to read socket's error queue instead of data queue. Possible
scenario of error queue usage is receiving completions for transmission
with MSG_ZEROCOPY flag. This patch also adds new defines: 'SOL_VSOCK'
and 'VSOCK_RECVERR'.

Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: sfp: add quirk for FS's 2.5G copper SFP

[ Upstream commit e27aca3760c08b7b05aea71068bd609aa93e7b35 ]

Add a quirk for a copper SFP that identifies itself as "FS" "SFP-2.5G-T".
This module's PHY is inaccessible, and can only run at 2500base-X with the
host without negotiation. Add a quirk to enable the 2500base-X interface mode
with 2500base-T support and disable auto negotiation.

Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Link: https://lore.kernel.org/r/20230925080059.266240-1-Raju.Lakkaraju@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: ath10k: Don't touch the CE interrupt registers after power up

[ Upstream commit 170c75d43a77dc937c58f07ecf847ba1b42ab74e ]

As talked about in commit d66d24ac300c ("ath10k: Keep track of which
interrupts fired, don't poll them"), if we access the copy engine
register at a bad time then ath10k can go boom. However, it's not
necessarily easy to know when it's safe to access them.

The ChromeOS test labs saw a crash that looked like this at
shutdown/reboot time (on a chromeos-5.15 kernel, but likely the
problem could also reproduce upstream):

Internal error: synchronous external abort: 96000010 [#1] PREEMPT SMP
...
CPU: 4 PID: 6168 Comm: reboot Not tainted 5.15.111-lockdep-19350-g1d624fe6758f #1 010b9b233ab055c27c6dc88efb0be2f4e9e86f51
Hardware name: Google Kingoftown (DT)
...
pc : ath10k_snoc_read32+0x50/0x74 [ath10k_snoc]
lr : ath10k_snoc_read32+0x24/0x74 [ath10k_snoc]
...
Call trace:
ath10k_snoc_read32+0x50/0x74 [ath10k_snoc ...]
ath10k_ce_disable_interrupt+0x190/0x65c [ath10k_core ...]
ath10k_ce_disable_interrupts+0x8c/0x120 [ath10k_core ...]
ath10k_snoc_hif_stop+0x78/0x660 [ath10k_snoc ...]
ath10k_core_stop+0x13c/0x1ec [ath10k_core ...]
ath10k_halt+0x398/0x5b0 [ath10k_core ...]
ath10k_stop+0xfc/0x1a8 [ath10k_core ...]
drv_stop+0x148/0x6b4 [mac80211 ...]
ieee80211_stop_device+0x70/0x80 [mac80211 ...]
ieee80211_do_stop+0x10d8/0x15b0 [mac80211 ...]
ieee80211_stop+0x144/0x1a0 [mac80211 ...]
__dev_close_many+0x1e8/0x2c0
dev_close_many+0x198/0x33c
dev_close+0x140/0x210
cfg80211_shutdown_all_interfaces+0xc8/0x1e0 [cfg80211 ...]
ieee80211_remove_interfaces+0x118/0x5c4 [mac80211 ...]
ieee80211_unregister_hw+0x64/0x1f4 [mac80211 ...]
ath10k_mac_unregister+0x4c/0xf0 [ath10k_core ...]
ath10k_core_unregister+0x80/0xb0 [ath10k_core ...]
ath10k_snoc_free_resources+0xb8/0x1ec [ath10k_snoc ...]
ath10k_snoc_shutdown+0x98/0xd0 [ath10k_snoc ...]
platform_shutdown+0x7c/0xa0
device_shutdown+0x3e0/0x58c
kernel_restart_prepare+0x68/0xa0
kernel_restart+0x28/0x7c

Though there's no known way to reproduce the problem, it makes sense
that it would be the same issue where we're trying to access copy
engine registers when it's not allowed.

Let's fix this by changing how we "disable" the interrupts. Instead of
tweaking the copy engine registers we'll just use disable_irq() and
enable_irq(). Then we'll configure the interrupts once at power up
time.

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.2.2.c10-00754-QCAHLSWMTPL-1

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230630151842.1.If764ede23c4e09a43a842771c2ddf99608f25f8e@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>

wifi: ath12k: mhi: fix potential memory leak in ath12k_mhi_register()

[ Upstream commit 47c27aa7ded4b8ead19b3487cc42a6185b762903 ]

mhi_alloc_controller() allocates a memory space for mhi_ctrl. When some
errors occur, mhi_ctrl should be freed by mhi_free_controller() and set
ab_pci->mhi_ctrl = NULL.

We can fix it by calling mhi_free_controller() when the failure happens
and set ab_pci->mhi_ctrl = NULL in all of the places where we call
mhi_free_controller().

Signed-off-by: Ma Ke <make_ruc2021@163.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230922021036.3604157-1-make_ruc2021@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: annotate data-races around sk->sk_dst_pending_confirm

[ Upstream commit eb44ad4e635132754bfbcb18103f1dcb7058aedd ]

This field can be read or written without socket lock being held.

Add annotations to avoid load-store tearing.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: annotate data-races around sk->sk_tx_queue_mapping

[ Upstream commit 0bb4d124d34044179b42a769a0c76f389ae973b6 ]

This field can be read or written without socket lock being held.

Add annotations to avoid load-store tearing.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>