serial: tegra: Change lower tolerance baud rate limit for tegra20 and tegra30

commit b40de7469ef135161c80af0e8c462298cc5dac00 upstream.

The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.

This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.

Fixes: d781ec21bae6 ("serial: tegra: report clk rate errors")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Patrik John <patrik.john@u-blox.com>
Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: pl011: Add ACPI SBSA UART match id

commit ac442a077acf9a6bf1db4320ec0c3f303be092b3 upstream.

The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000

Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.

Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.

Cc: <stable@vger.kernel.org>
Signed-off-by: Pierre Gondois <Pierre.Gondois@arm.com>
Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: serial: msm_serial: Deactivate RX DMA for polling support

commit 7492ffc90fa126afb67d4392d56cb4134780194a upstream.

The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.

This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:

* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received

This repeats then for each group of 4 input values.

This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.

RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.

Fixes: 99693945013a ("tty: serial: msm: Add RX DMA support")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/64/mm: Map all kernel memory into trampoline_pgd

commit 51523ed1c26758de1af7e58730a656875f72f783 upstream.

The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.

This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:

  #ifdef CONFIG_X86_32
   load_cr3(initial_page_table);
  #else
   write_cr3(real_mode_header->trampoline_pgd);

   /* Exiting long mode will fail if CR4.PCIDE is set. */
   if (boot_cpu_has(X86_FEATURE_PCID))
   cr4_clear_bits(X86_CR4_PCIDE);
  #endif

   /* Jump to the identity-mapped low memory code */
  #ifdef CONFIG_X86_32
   asm volatile("jmpl *%0" : :
        "rm" (real_mode_header->machine_real_restart_asm),
        "a" (type));
  #else
   asm volatile("ljmpl *%0" : :
        "m" (real_mode_header->machine_real_restart_asm),
        "D" (type));
  #endif

The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.

The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.

Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.

Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/tsc: Disable clocksource watchdog for TSC on qualified platorms

commit b50db7095fe002fa3e16605546cba66bf1b68a3e upstream.

There are cases that the TSC clocksource is wrongly judged as unstable by
the clocksource watchdog mechanism which tries to validate the TSC against
HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to
check the validity of a watchdog, Thomas Gleixner proposed [1]:

"I'm inclined to lift that requirement when the CPU has:

    1) X86_FEATURE_CONSTANT_TSC
    2) X86_FEATURE_NONSTOP_TSC
    3) X86_FEATURE_NONSTOP_TSC_S3
    4) X86_FEATURE_TSC_ADJUST
    5) At max. 4 sockets

 After two decades of horrors we're finally at a point where TSC seems
 to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST
 was really key as we can now detect even small modifications reliably
 and the important point is that we can cure them as well (not pretty
 but better than all other options)."

As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations
of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC
and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive
to use maximal 2 sockets.

The check is done inside tsc_init() before registering 'tsc-early' and
'tsc' clocksources, as there were cases that both of them had been
wrongly judged as unreliable.

For more background of tsc/watchdog, there is a good summary in [2]

[tglx} Update vs. jiffies:

  On systems where the only remaining clocksource aside of TSC is jiffies
  there is no way to make this work because that creates a circular
  dependency. Jiffies accuracy depends on not missing a periodic timer
  interrupt, which is not guaranteed. That could be detected by TSC, but as
  TSC is not trusted this cannot be compensated. The consequence is a
  circulus vitiosus which results in shutting down TSC and falling back to
  the jiffies clocksource which is even more unreliable.

[1]. https://lore.kernel.org/lkml/87eekfk8bd.fsf@nanos.tec.linutronix.de/
[2]. https://lore.kernel.org/lkml/87a6pimt1f.ffs@nanos.tec.linutronix.de/

[ tglx: Refine comment and amend changelog ]

Fixes: 6e3cd95234dc ("x86/hpet: Use another crystalball to evaluate HPET usability")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211117023751.24190-2-feng.tang@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/tsc: Add a timer to make sure TSC_adjust is always checked

commit c7719e79347803b8e3b6b50da8c6db410a3012b5 upstream.

The TSC_ADJUST register is checked every time a CPU enters idle state, but
Thomas Gleixner mentioned there is still a caveat that a system won't enter
idle [1], either because it's too busy or configured purposely to not enter
idle.

Setup a periodic timer (every 10 minutes) to make sure the check is
happening on a regular base.

[1] https://lore.kernel.org/lkml/875z286xtk.fsf@nanos.tec.linutronix.de/

Fixes: 6e3cd95234dc ("x86/hpet: Use another crystalball to evaluate HPET usability")
Requested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "Paul E. McKenney" <paulmck@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20211117023751.24190-1-feng.tang@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdnsp: Fix a NULL pointer dereference in cdnsp_endpoint_init()

commit 37307f7020ab38dde0892a578249bf63d00bca64 upstream.

In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring
and there is a dereference of it in cdnsp_endpoint_init(), which could
lead to a NULL pointer dereference on failure of cdnsp_ring_alloc().

Fix this bug by adding a check of pep->ring.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable <stable@vger.kernel.org>
Acked-by: Pawel Laszczak <pawell@cadence.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130172700.206650-1-zhou1615@umn.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdns3: gadget: fix new urb never complete if ep cancel previous requests

commit 387c2b6ba197c6df28e75359f7d892f7c8dec204 upstream.

This issue was found at android12 MTP.
1. MTP submit many out urb request.
2. Cancel left requests (>20) when enough data get from host
3. Send ACK by IN endpoint.
4. MTP submit new out urb request.
5. 4's urb never complete.

TRACE LOG:

MtpServer-2157    [000] d..3  1287.150391: cdns3_ep_dequeue: ep1out: req: 00000000299e6836, req buff 000000009df42287, length: 0/16384 zsi, status: -115, trb: [start:87, end:87: virt addr 0x80004000ffd50420], flags:1 SID: 0
MtpServer-2157    [000] d..3  1287.150410: cdns3_gadget_giveback: ep1out: req: 00000000299e6836, req buff 000000009df42287, length: 0/16384 zsi, status: -104, trb: [start:87, end:87: virt addr 0x80004000ffd50420], flags:0 SID: 0
MtpServer-2157    [000] d..3  1287.150433: cdns3_ep_dequeue: ep1out: req: 0000000080b7bde6, req buff 000000009ed5c556, length: 0/16384 zsi, status: -115, trb: [start:88, end:88: virt addr 0x80004000ffd5042c], flags:1 SID: 0
MtpServer-2157    [000] d..3  1287.150446: cdns3_gadget_giveback: ep1out: req: 0000000080b7bde6, req buff 000000009ed5c556, length: 0/16384 zsi, status: -104, trb: [start:88, end:88: virt addr 0x80004000ffd5042c], flags:0 SID: 0
....
MtpServer-2157    [000] d..1  1293.630410: cdns3_alloc_request: ep1out: req: 00000000afbccb7d, req buff 0000000000000000, length: 0/0 zsi, status: 0, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0
MtpServer-2157    [000] d..2  1293.630421: cdns3_ep_queue: ep1out: req: 00000000afbccb7d, req buff 00000000871caf90, length: 0/512 zsi, status: -115, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0
MtpServer-2157    [000] d..2  1293.630445: cdns3_wa1: WA1: ep1out set guard
MtpServer-2157    [000] d..2  1293.630450: cdns3_wa1: WA1: ep1out restore cycle bit
MtpServer-2157    [000] d..2  1293.630453: cdns3_prepare_trb: ep1out: trb 000000007317b3ee, dma buf: 0xffd5bc00, size: 512, burst: 128 ctrl: 0x00000424 (C=0, T=0, ISP, IOC, Normal) SID:0 LAST_SID:0
MtpServer-2157    [000] d..2  1293.630460: cdns3_doorbell_epx: ep1out, ep_trbaddr ffd50414
....
irq/241-5b13000-2154    [000] d..1  1293.680849: cdns3_epx_irq: IRQ for ep1out: 01000408 ISP , ep_traddr: ffd508ac ep_last_sid: 00000000 use_streams: 0
irq/241-5b13000-2154    [000] d..1  1293.680858: cdns3_complete_trb: ep1out: trb 0000000021a11b54, dma buf: 0xffd50420, size: 16384, burst: 128 ctrl: 0x00001810 (C=0, T=0, CHAIN, LINK) SID:0 LAST_SID:0
irq/241-5b13000-2154    [000] d..1  1293.680865: cdns3_request_handled: Req: 00000000afbccb7d not handled, DMA pos: 185, ep deq: 88, ep enq: 185, start trb: 184, end trb: 184

Actually DMA pos already bigger than previous submit request afbccb7d's TRB (184-184). The reason of (not handled) is that deq position is wrong.

The TRB link is below when irq happen.

DEQ LINK LINK LINK LINK LINK .... TRB(afbccb7d):START  DMA(EP_TRADDR).

Original code check LINK TRB, but DEQ just move one step.

LINK DEQ LINK LINK LINK LINK .... TRB(afbccb7d):START  DMA(EP_TRADDR).

This patch skip all LINK TRB and sync DEQ to trb's start.

LINK LINK LINK LINK LINK .... DEQ = TRB(afbccb7d):START  DMA(EP_TRADDR).

Acked-by: Peter Chen <peter.chen@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jun Li <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20211130154239.8029-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: tcpm: Wait in SNK_DEBOUNCED until disconnect

commit fbcd13df1e78eb2ba83a3c160eefe2d6f574beaf upstream.

Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."

This change makes TCPM to wait in SNK_DEBOUNCED state until
CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously,
TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON.
This causes TCPM to loop continuously when connected to a
faulty power source that does not present vbus. Waiting in
SNK_DEBOUNCED also ensures that TCPM is adherant to
"4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements.

[ 6169.280751] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 6169.280759] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS]
[ 6169.280771] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS]
[ 6169.282427] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected]
[ 6169.450825] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 6169.450834] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS]
[ 6169.930892] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms]
[ 6169.931296] disable vbus discharge ret:0
[ 6169.931301] Setting usb_comm capable false
[ 6169.932783] Setting voltage/current limit 0 mV 0 mA
[ 6169.932802] polarity 0
[ 6169.933706] Requesting mux state 0, usb-role 0, orientation 0
[ 6169.936689] cc:=0
[ 6169.936812] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS]
[ 6169.937157] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 6170.036880] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 6170.036890] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev2 NONE_AMS]
[ 6170.036896] Start toggling
[ 6170.041412] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 6170.042973] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected]
[ 6170.042976] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS]
[ 6170.042981] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS]
[ 6170.213014] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms]
[ 6170.213019] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS]
[ 6170.693068] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms]
[ 6170.693304] disable vbus discharge ret:0
[ 6170.693308] Setting usb_comm capable false
[ 6170.695193] Setting voltage/current limit 0 mV 0 mA
[ 6170.695210] polarity 0
[ 6170.695990] Requesting mux state 0, usb-role 0, orientation 0
[ 6170.701896] cc:=0
[ 6170.702181] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS]
[ 6170.703343] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected]

Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20211130001825.3142830-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: NO_LPM quirk Lenovo Powered USB-C Travel Hub

commit d2a004037c3c6afd36d40c384d2905f47cd51c57 upstream.

This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71

Disable LPM to resolve the issue.

Signed-off-by: Ole Ernst <olebowle@gmx.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211127090546.52072-1-olebowle@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: Fix commad ring abort, write all 64 bits to CRCR register.

commit 09f736aa95476631227d2dc0e6b9aeee1ad7ed58 upstream.

Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.

The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.

Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.

The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.

Fixes: ff0e50d3564f ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vgacon: Propagate console boot parameters before calling `vc_resize'

commit 3dfac26e2ef29ff2abc2a75aa4cd48fce25a2c4b upstream.

Fix a division by zero in `vgacon_resize' with a backtrace like:

vgacon_resize
vc_do_resize
vgacon_init
do_bind_con_driver
do_unbind_con_driver
fbcon_fb_unbind
do_unregister_framebuffer
do_register_framebuffer
register_framebuffer
__drm_fb_helper_initial_config_and_unlock
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread
kthread

caused by `c->vc_cell_height' not having been initialized.  This has
only started to trigger with commit 860dafa90259 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").

Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on.  Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.

In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon.  Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.

Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then.  Adjust the comment accordingly.

Fixes: 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console")
Cc: stable@vger.kernel.org # v2.6.18+
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Mark cr16 CPU clocksource unstable on all SMP machines

commit afdb4a5b1d340e4afffc65daa21cc71890d7d589 upstream.

In commit c8c3735997a3 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour.  On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.

This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.

Fixes: c8c3735997a3 ("parisc: Enhance detection of synchronous cr16 clocksources")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v5.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix "make install" on newer debian releases

commit 0f9fee4cdebfbe695c297e5b603a275e2557c1cc upstream.

On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

parisc: Fix KBUILD_IMAGE for self-extracting kernel

commit 1d7c29b77725d05faff6754d2f5e7c147aedcf93 upstream.

Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting
(CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built.
This fixes the bindeb-pkg make target.

Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250_bcm7271: UART errors after resuming from S2

[ Upstream commit 9cabe26e65a893afd5846908aa393bd283ab6609 ]

There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.

Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Sync TIR params updates against concurrent create/modify

[ Upstream commit 4cce2ccf08fbc27ae34ce0e72db15166e7b5f6a7 ]

Transport Interface Receive (TIR) objects perform the packet processing and
reassembly and is also responsible for demultiplexing the packets into the
different RQs.

There are certain TIR context attributes that propagate to the pointed RQs
and applied to them (like packet_merge offloads (LRO/SHAMPO) and
tunneled_offload_en).  When TIRs do not agree on attributes values, a "last
one wins" policy is applied.  Hence, if not synced properly, a race between
TIR params update and a concurrent TIR create/modify operation might yield
to a mismatch between the shadow parameters in SW and the actual applied
state of the RQs in HW.

tunneled_offload_en is a fixed attribute per profile, while packet merge
offload state might be toggled and get out-of-sync. When this happens,
packet_merge offload might be working although not requested, or the
opposite.

All updates to packet_merge state and all create/modify operations of
regular redirection/steering TIRs are done under the same priv->state_lock,
so they do not run in parallel, and no race is possible.

However, there are other kind of TIRs (acceleration offloads TIRs, like TLS
TIRs) which are created on demand for each new connection without holding
the coarse priv->state_lock, hence might race.

Fix this by synchronizing all packet_merge state reads and writes against
all TIR create/modify operations. Include the modify operations of the
regular redirection steering TIRs under the new lock, for better code
layering and division of responsibilities.

Fixes: 1182f3659357 ("net/mlx5e: kTLS, Add kTLS RX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Rename TIR lro functions to TIR packet merge functions

[ Upstream commit eaee12f046924eeb1210c7e4f3b326603ff1bd85 ]

This series introduces new packet merge type, therefore rename lro
functions to packet merge to support the new merge type:
- Generalize + rename mlx5e_build_tir_ctx_lro to
  mlx5e_build_tir_ctx_packet_merge.
- Rename mlx5e_modify_tirs_lro to mlx5e_modify_tirs_packet_merge.
- Rename lro bit in mlx5_ifc_modify_tir_bitmask_bits to packet_merge.
- Rename lro_en in mlx5e_params to packet_merge_type type and combine
  packet_merge params into one struct mlx5e_packet_merge_param.

Signed-off-by: Khalid Manaa <khalidm@nvidia.com>
Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Rename lro_timeout to packet_merge_timeout

[ Upstream commit 50f477fe9933193e960785f1192be801d7cd307a ]

TIR stands for transport interface receive, the TIR object is
responsible for performing all transport related operations on
the receive side like packet processing, demultiplexing the packets
to different RQ's, etc.
lro_timeout is a field in the TIR that is used to set the timeout for lro
session, this series introduces new packet merge type, therefore rename
lro_timeout to packet_merge_timeout for all packet merge types.

Signed-off-by: Ben Ben-Ishay <benishay@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/mmu: Remove spurious TLB flushes in TDP MMU zap collapsible path

[ Upstream commit 4b85c921cd393764d22c0cdab6d7d5d120aa0980 ]

Drop the "flush" param and return values to/from the TDP MMU's helper for
zapping collapsible SPTEs.  Because the helper runs with mmu_lock held
for read, not write, it uses tdp_mmu_zap_spte_atomic(), and the atomic
zap handles the necessary remote TLB flush.

Similarly, because mmu_lock is dropped and re-acquired between zapping
legacy MMUs and zapping TDP MMUs, kvm_mmu_zap_collapsible_sptes() must
handle remote TLB flushes from the legacy MMU before calling into the TDP
MMU.

Fixes: e2209710ccc5d ("KVM: x86/mmu: Skip rmap operations if rmaps not allocated")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211120045046.3940942-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/mmu: Rename slot_handle_leaf to slot_handle_level_4k

[ Upstream commit 610265ea3da117db435868bd109f1861534a5634 ]

slot_handle_leaf is a misnomer because it only operates on 4K SPTEs
whereas "leaf" is used to describe any valid terminal SPTE (4K or
large page). Rename slot_handle_leaf to slot_handle_level_4k to
avoid confusion.

Making this change makes it more obvious there is a benign discrepency
between the legacy MMU and the TDP MMU when it comes to dirty logging.
The legacy MMU only iterates through 4K SPTEs when zapping for
collapsing and when clearing D-bits. The TDP MMU, on the other hand,
iterates through SPTEs on all levels.

The TDP MMU behavior of zapping SPTEs at all levels is technically
overkill for its current dirty logging implementation, which always
demotes to 4k SPTES, but both the TDP MMU and legacy MMU zap if and only
if the SPTE can be replaced by a larger page, i.e. will not spuriously
zap 2m (or larger) SPTEs. Opportunistically add comments to explain this
discrepency in the code.

Signed-off-by: David Matlack <dmatlack@google.com>
Message-Id: <20211019162223.3935109-1-dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: SEV: Return appropriate error codes if SEV-ES scratch setup fails

[ Upstream commit 75236f5f2299b502e4b9b267c1ce3bc14a222ceb ]

Return appropriate error codes if setting up the GHCB scratch area for an
SEV-ES guest fails.  In particular, returning -EINVAL instead of -ENOMEM
when allocating the kernel buffer could be confusing as userspace would
likely suspect a guest issue.

Fixes: 8f423a80d299 ("KVM: SVM: Support MMIO for an SEV-ES guest")
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211109222350.2266045-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/uclamp: Fix rq->uclamp_max not set on first enqueue

[ Upstream commit 315c4f884800c45cb6bd8c90422fad554a8b9588 ]

Commit d81ae8aac85c ("sched/uclamp: Fix initialization of struct
uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to
match the woken up task's uclamp_max when the rq is idle.

The code was relying on rq->uclamp_max initialized to zero, so on first
enqueue

static inline void uclamp_rq_inc_id(struct rq *rq, struct task_struct *p,
    enum uclamp_id clamp_id)
{
...

if (uc_se->value > READ_ONCE(uc_rq->value))
WRITE_ONCE(uc_rq->value, uc_se->value);
}

was actually resetting it. But since commit d81ae8aac85c changed the
default to 1024, this no longer works. And since rq->uclamp_flags is
also initialized to 0, neither above code path nor uclamp_idle_reset()
update the rq->uclamp_max on first wake up from idle.

This is only visible from first wake up(s) until the first dequeue to
idle after enabling the static key. And it only matters if the
uclamp_max of this task is < 1024 since only then its uclamp_max will be
effectively ignored.

Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to
ensure uclamp_idle_reset() is called which then will update the rq
uclamp_max value as expected.

Fixes: d81ae8aac85c ("sched/uclamp: Fix initialization of struct uclamp_rq")
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <Valentin.Schneider@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Link: https://lkml.kernel.org/r/20211202112033.1705279-1-qais.yousef@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

preempt/dynamic: Fix setup_preempt_mode() return value

[ Upstream commit 9ed20bafc85806ca6c97c9128cec46c3ef80ae86 ]

__setup() callbacks expect 1 for success and 0 for failure. Correct the
usage here to reflect that.

Fixes: 826bfeb37bb4 ("preempt/dynamic: Support dynamic preempt with preempt= boot option")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211203233203.133581-1-ahalaney@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/xen: Add xenpv_restore_regs_and_return_to_usermode()

[ Upstream commit 5c8f6a2e316efebb3ba93d8c1af258155dcf5632 ]

In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.

In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.

This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.

And, with  XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.

 [ bp: Massage commit message. ]

Fixes: 7f2590a110b8 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/entry: Use the correct fence macro after swapgs in kernel CR3

[ Upstream commit 1367afaa2ee90d1c956dfc224e199fcb3ff3f8cc ]

The commit

  c75890700455 ("x86/entry/64: Remove unneeded kernel CR3 switching")

removed a CR3 write in the faulting path of load_gs_index().

But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().

Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.

 [ bp: Massage commit message and comment. ]

Fixes: c75890700455 ("x86/entry/64: Remove unneeded kernel CR3 switching")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211126101209.8613-3-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/entry: Add a fence for kernel entry SWAPGS in paranoid_entry()

[ Upstream commit c07e45553da1808aa802e9f0ffa8108cfeaf7a17 ]

Commit

  18ec54fdd6d18 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")

added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.

But

  96b2371413e8f ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")

changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.

Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.

  [ bp: Massage, fix typos, remove obsolete comment while at it. ]

Fixes: 96b2371413e8f ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/sev: Fix SEV-ES INS/OUTS instructions for word, dword, and qword

[ Upstream commit 1d5379d0475419085d3575bd9155f2e558e96390 ]

Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.

This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.

Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.

Fixes: f980f9c31a923 (x86/sev-es: Compile early handler code into kernel image)
Signed-off-by: Michael Sterritt <sterritt@google.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Gonda <pgonda@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

io-wq: don't retry task_work creation failure on fatal conditions

[ Upstream commit a226abcd5d427fe9d42efc442818a4a1821e2664 ]

We don't want to be retrying task_work creation failure if there's
an actual signal pending for the parent task. If we do, then we can
enter an infinite loop of perpetually retrying and each retry failing
with -ERESTARTNOINTR because a signal is pending.

Fixes: 3146cba99aa2 ("io-wq: make worker creation resilient against signals")
Reported-by: Florian Fischer <florian.fl.fischer@fau.de>
Link: https://lore.kernel.org/io-uring/20211202165606.mqryio4yzubl7ms5@pasture/
Tested-by: Florian Fischer <florian.fl.fischer@fau.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "drm/i915: Implement Wa_1508744258"

[ Upstream commit 72641d8d60401a5f1e1a0431ceaf928680d34418 ]

This workarounds are causing hangs, because I missed the fact that it
needs to be enabled for all cases and disabled when doing a resolve
pass.

So KMD only needs to whitelist it and UMD will be the one setting it
on per case.

This reverts commit 28ec02c9cbebf3feeaf21a59df9dfbc02bda3362.

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4145
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes: 28ec02c9cbeb ("drm/i915: Implement Wa_1508744258")
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211119140931.32791-1-jose.souza@intel.com
(cherry picked from commit f3799ff16fcfacd44aee55db162830df461b631f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mctp: Don't let RTM_DELROUTE delete local routes

[ Upstream commit 76d001603c509562181f3787a7065b8e163bc7b9 ]

We need to test against the existing route type, not
the rtm_type in the netlink request.

Fixes: 83f0a0b7285b ("mctp: Specify route types, require rtm_type in RTM_*ROUTE messages")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: VMX: Set failure code in prepare_vmcs02()

[ Upstream commit bfbb307c628676929c2d329da0daf9d22afa8ad2 ]

The error paths in the prepare_vmcs02() function are supposed to set
*entry_failure_code but this path does not.  It leads to using an
uninitialized variable in the caller.

Fixes: 71f7347025bf ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20211130125337.GB24578@kili>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/pmu: Fix reserved bits for AMD PerfEvtSeln register

[ Upstream commit cb1d220da0faa5ca0deb93449aff953f0c2cce6d ]

If we run the following perf command in an AMD Milan guest:

  perf stat \
  -e cpu/event=0x1d0/ \
  -e cpu/event=0x1c7/ \
  -e cpu/umask=0x1f,event=0x18e/ \
  -e cpu/umask=0x7,event=0x18e/ \
  -e cpu/umask=0x18,event=0x18e/ \
  ./workload

dmesg will report a #GP warning from an unchecked MSR access
error on MSR_F15H_PERF_CTLx.

This is because according to APM (Revision: 4.03) Figure 13-7,
the bits [35:32] of AMD PerfEvtSeln register is a part of the
event select encoding, which extends the EVENT_SELECT field
from 8 bits to 12 bits.

Opportunistically update pmu->reserved_bits for reserved bit 19.

Reported-by: Jim Mattson <jmattson@google.com>
Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM")
Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211118130320.95997-1-likexu@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: E-Switch, Check group pointer before reading bw_share value

[ Upstream commit 5c4e8ae7aa4875041102406801ee434e6c581aef ]

If log_esw_max_sched_depth is not supported group pointer of the vport
is NULL. Hence, check the pointer before reading bw_share value.

Fixes: 0fe132eac38c ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: E-Switch, fix single FDB creation on BlueField

[ Upstream commit 43a0696f11567278b9412f947e43dd7906c831a8 ]

Always use MLX5_FLOW_TABLE_OTHER_VPORT flag when creating egress ACL
table for single FDB. Not doing so on BlueField will make firmware fail
the command. On BlueField the E-Switch manager is the ECPF (vport 0xFFFE)
which is filled in the flow table creation command but as the
other_vport field wasn't set the firmware complains about a bad parameter.

This is different from a regular HCA where the E-Switch manager vport is
the PF (vport 0x0). Passing MLX5_FLOW_TABLE_OTHER_VPORT will make the
firmware happy both on BlueField and on regular HCAs without special
condition for each.

This fixes the bellow firmware syndrome:
mlx5_cmd_check:819:(pid 571): CREATE_FLOW_TABLE(0x930) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x754a4)

Fixes: db202995f503 ("net/mlx5: E-Switch, add logic to enable shared FDB")
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: E-switch, Respect BW share of the new group

[ Upstream commit 1e59b32e45e47c8ea5455182286ba010bfa87813 ]

To enable transmit schduler on vport FW require non-zero configuration
for vport's TSAR. If vport added to the group which has configured BW
share value and TX rate values of the vport are zero, then scheduler
wouldn't be enabled on this vport.
Fix that by calling BW normalization if BW share of the new group is
configured.

Fixes: 0fe132eac38c ("net/mlx5: E-switch, Allow to add vports to rate groups")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5: Move MODIFY_RQT command to ignore list in internal error state

[ Upstream commit e45c0b34493c24eeeebf89f63a5293aac7728ed7 ]

When the device is in internal error state, command interface isn't
accessible and the driver decides which commands to fail and which
to ignore.

Move the MODIFY_RQT command to the ignore list in order to avoid
the following redundant warning messages in internal error state:

mlx5_core 0000:82:00.1: mlx5e_rss_disable:419:(pid 23754): Failed to redirect RQT 0x0 to drop RQ 0xc00848: err = -5
mlx5_core 0000:82:00.1: mlx5e_rx_res_channels_deactivate:598:(pid 23754): Failed to redirect direct RQT 0x1 to drop RQ 0xc00848 (channel 0): err = -5
mlx5_core 0000:82:00.1: mlx5e_rx_res_channels_deactivate:607:(pid 23754): Failed to redirect XSK RQT 0x19 to drop RQ 0xc00848 (channel 0): err = -5

Fixes: 43ec0f41fa73 ("net/mlx5e: Hide all implementation details of mlx5e_rx_res")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Fix missing IPsec statistics on uplink representor

[ Upstream commit 51ebf5db67f5c6aed79c05f1aa5137bdf5ca6614 ]

The cited patch added the IPsec support to uplink representor, however
as uplink representors have his private statistics where IPsec stats
is not part of it, that effectively makes IPsec stats hidden when uplink
representor stats queried.

Resolve by adding IPsec stats to uplink representor private statistics.

Fixes: 5589b8f1a2c7 ("net/mlx5e: Add IPsec support to uplink representor")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: SEV: initialize regions_list of a mirror VM

[ Upstream commit 2b347a387811cb4aa7bcdb96e9203c5019a6fb41 ]

This was broken before the introduction of KVM_CAP_VM_MOVE_ENC_CONTEXT_FROM,
but technically harmless because the region list was unused for a mirror
VM.  However, it is untidy and it now causes a NULL pointer access when
attempting to move the encryption context of a mirror VM.

Fixes: 54526d1fd593 ("KVM: x86: Support KVM VMs sharing SEV context")
Message-Id: <20211123005036.2954379-7-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: X86: Fix when shadow_root_level=5 && guest root_level<4

[ Upstream commit 12ec33a705749e18d9588b0a0e69e02821371156 ]

If the is an L1 with nNPT in 32bit, the shadow walk starts with
pae_root.

Fixes: a717a780fc4e ("KVM: x86/mmu: Support shadowing NPT when 5-level paging is enabled in host)
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-2-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlwifi: Fix memory leaks in error handling path

[ Upstream commit a571bc28326d9f3e13f5f2d9cda2883e0631b0ce ]

Should an error occur (invalid TLV len or memory allocation failure), the
memory already allocated in 'reduce_power_data' should be freed before
returning, otherwise it is leaking.

Fixes: 9dad325f9d57 ("iwlwifi: support loading the reduced power table from UEFI")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1504cd7d842d13ddb8244e18004523128d5c9523.1636615284.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: rk817: Add module alias for rk817-codec

[ Upstream commit 428ee30a05cd1362c8aa86a4c909b0d1c6bc48a4 ]

Without a module alias, autoloading the driver does not occurr
when it is built as a module.

By adding a module alias, the driver now probes fine automatically
and therefore analog audio output works as it should.

Fixes: 0d6a04da9b25 ("ASoC: Add Rockchip rk817 audio CODEC support")
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20211121150521.159543-1-frattaroli.nicolas@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Restore error return on invalid fence

[ Upstream commit 067ecab9eef620d41040715669e5fcdc2f8ff963 ]

When converting to use an idr to map userspace fence seqno values back
to a dma_fence, we lost the error return when userspace passes seqno
that is larger than the last submitted fence.  Restore this check.

Reported-by: Akhil P Oommen <akhilpo@codeaurora.org>
Fixes: a61acbbe9cf8 ("drm/msm: Track "seqno" fences by idr")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111192457.747899-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Fix wait_fence submitqueue leak

[ Upstream commit ea0006d390a28012f8187717aea61498b2b341e5 ]

We weren't dropping the submitqueue reference in all paths.  In
particular, when the fence has already been signalled. Split out
a helper to simplify handling this in the various different return
paths.

Fixes: a61acbbe9cf8 ("drm/msm: Track "seqno" fences by idr")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211111192457.747899-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm: Fix mmap to include VM_IO and VM_DONTDUMP

[ Upstream commit 3466d9e217b337bf473ee629c608e53f9f3ab786 ]

In commit 510410bfc034 ("drm/msm: Implement mmap as GEM object
function") we switched to a new/cleaner method of doing things. That's
good, but we missed a little bit.

Before that commit, we used to _first_ run through the
drm_gem_mmap_obj() case where `obj->funcs->mmap()` was NULL. That meant
that we ran:

  vma->vm_flags |= VM_IO | VM_PFNMAP | VM_DONTEXPAND | VM_DONTDUMP;
  vma->vm_page_prot = pgprot_writecombine(vm_get_page_prot(vma->vm_flags));
  vma->vm_page_prot = pgprot_decrypted(vma->vm_page_prot);

...and _then_ we modified those mappings with our own. Now that
`obj->funcs->mmap()` is no longer NULL we don't run the default
code. It looks like the fact that the vm_flags got VM_IO / VM_DONTDUMP
was important because we're now getting crashes on Chromebooks that
use ARC++ while logging out. Specifically a crash that looks like this
(this is on a 5.10 kernel w/ relevant backports but also seen on a
5.15 kernel):

  Unable to handle kernel paging request at virtual address ffffffc008000000
  Mem abort info:
    ESR = 0x96000006
    EC = 0x25: DABT (current EL), IL = 32 bits
    SET = 0, FnV = 0
    EA = 0, S1PTW = 0
  Data abort info:
    ISV = 0, ISS = 0x00000006
    CM = 0, WnR = 0
  swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000008293d000
  [ffffffc008000000] pgd=00000001002b3003, p4d=00000001002b3003,
                     pud=00000001002b3003, pmd=0000000000000000
  Internal error: Oops: 96000006 [#1] PREEMPT SMP
  [...]
  CPU: 7 PID: 15734 Comm: crash_dump64 Tainted: G W 5.10.67 #1 [...]
  Hardware name: Qualcomm Technologies, Inc. sc7280 IDP SKU2 platform (DT)
  pstate: 80400009 (Nzcv daif +PAN -UAO -TCO BTYPE=--)
  pc : __arch_copy_to_user+0xc0/0x30c
  lr : copyout+0xac/0x14c
  [...]
  Call trace:
   __arch_copy_to_user+0xc0/0x30c
   copy_page_to_iter+0x1a0/0x294
   process_vm_rw_core+0x240/0x408
   process_vm_rw+0x110/0x16c
   __arm64_sys_process_vm_readv+0x30/0x3c
   el0_svc_common+0xf8/0x250
   do_el0_svc+0x30/0x80
   el0_svc+0x10/0x1c
   el0_sync_handler+0x78/0x108
   el0_sync+0x184/0x1c0
  Code: f8408423 f80008c3 910020c6 36100082 (b8404423)

Let's add the two flags back in.

While we're at it, the fact that we aren't running the default means
that we _don't_ need to clear out VM_PFNMAP, so remove that and save
an instruction.

NOTE: it was confirmed that VM_IO was the important flag to fix the
problem I was seeing, but adding back VM_DONTDUMP seems like a sane
thing to do so I'm doing that too.

Fixes: 510410bfc034 ("drm/msm: Implement mmap as GEM object function")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211110113334.1.I1687e716adb2df746da58b508db3f25423c40b27@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/msm/devfreq: Fix OPP refcnt leak

[ Upstream commit 59ba1b2b4825342676300f66d785764be3fcb093 ]

Reported-by: Douglas Anderson <dianders@chromium.org>
Fixes: 9bc95570175a ("drm/msm: Devfreq tuning")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-By: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105202021.181092-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/mmu: Pass parameter flush as false in kvm_tdp_mmu_zap_collapsible_sptes()

[ Upstream commit 8ed716ca7dc91f058be0ba644a3048667a20db13 ]

Since tlb flush has been done for legacy MMU before
kvm_tdp_mmu_zap_collapsible_sptes(), so the parameter flush
should be false for kvm_tdp_mmu_zap_collapsible_sptes().

Fixes: e2209710ccc5d ("KVM: x86/mmu: Skip rmap operations if rmaps not allocated")
Signed-off-by: Hou Wenlong <houwenlong93@linux.alibaba.com>
Message-Id: <21453a1d2533afb6e59fb6c729af89e771ff2e76.1637140154.git.houwenlong93@linux.alibaba.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: x86/mmu: Skip tlb flush if it has been done in zap_gfn_range()

[ Upstream commit c7785d85b6c6cc9f3d0f1a8cab128f4062b30abb ]

If the parameter flush is set, zap_gfn_range() would flush remote tlb
when yield, then tlb flush is not needed outside. So use the return
value of zap_gfn_range() directly instead of OR on it in
kvm_unmap_gfn_range() and kvm_tdp_mmu_unmap_gfn_range().

Fixes: 3039bcc744980 ("KVM: Move x86's MMU notifier memslot walkers to generic code")
Signed-off-by: Hou Wenlong <houwenlong93@linux.alibaba.com>
Message-Id: <5e16546e228877a4d974f8c0e448a93d52c7a5a9.1637140154.git.houwenlong93@linux.alibaba.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

atlantic: Remove warn trace message.

commit 060a0fb721ec5bbe02ae322e434ec87dc25ed6e9 upstream.

Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state

Fixes: 508f2e3dce454 ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atlantic: Fix statistics logic for production hardware

commit 2087ced0fc3a6d45203925750a2b1bcd5402e639 upstream.

B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.

Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove Half duplex mode speed capabilities.

commit 03fa512189eb9b55ded5f3e81ad638315555b340 upstream.

Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.

Fixes: 071a02046c262 ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atlantic: Add missing DIDs and fix 115c.

commit 413d5e09caa5a11da9c7d72401ba0588466a04c0 upstream.

At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.

Fixes: b3f0c79cba206 ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atlantic: Fix to display FW bundle version instead of FW mac version.

commit 2465c802232bc8d2b5bd83b55b08d05c11808704 upstream.

The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.

Fixes: c1be0bf092bd2 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atlatnic: enable Nbase-t speeds with base-t

commit aa685acd98eae25d5351e30288d6cfb65b9c80a5 upstream.

When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.

Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

atlantic: Increase delay for fw transactions

commit aa1dcb5646fdf34a15763facf4bf5e482a2814ca upstream.

The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.

Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: kms: Fix previous HVS commit wait

commit 6052a3110be208e547a4a8aeb184446199a16e8a upstream.

Our current code is supposed to serialise the commits by waiting for all
the drm_crtc_commits associated to the previous HVS state.

However, assuming we have two CRTCs running and being configured and we
configure each one alternately, we end up in a situation where we're
not waiting at all.

Indeed, starting with a state (state 0) where both CRTCs are running,
and doing a commit (state 1) on the first CRTC (CRTC 0), we'll associate
its commit to its assigned FIFO in vc4_hvs_state.

If we get a new commit (state 2), this time affecting the second CRTC
(CRTC 1), the DRM core will allow both commits to execute in parallel
(assuming they don't have any share resources).

Our code in vc4_atomic_commit_tail is supposed to make sure we only get
one commit at a time and serialised by order of submission. It does so
by using for_each_old_crtc_in_state, making sure that the CRTC has a
FIFO assigned, is used, and has a commit pending. If it does, then we'll
wait for the commit before going forward.

During the transition from state 0 to state 1, as our old CRTC state we
get the CRTC 0 state 0, its commit, we wait for it, everything works fine.

During the transition from state 1 to state 2 though, the use of
for_each_old_crtc_in_state is wrong. Indeed, while the code assumes it's
returning the state of the CRTC in the old state (so CRTC 0 state 1), it
actually returns the old state of the CRTC affected by the current
commit, so CRTC 0 state 0 since it wasn't part of state 1.

Due to this, if we alternate between the configuration of CRTC 0 and
CRTC 1, we never actually wait for anything since we should be waiting
on the other every time, but it never is affected by the previous
commit.

Change the logic to, at every commit, look at every FIFO in the previous
HVS state, and if it's in use and has a commit associated to it, wait
for that commit.

Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-7-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: kms: Don't duplicate pending commit

commit d354699e2292c60f25496d3c31ce4e7b1563b899 upstream.

Our HVS global state, when duplicated, will also copy the pointer to the
drm_crtc_commit (and increase the reference count) for each FIFO if the
pointer is not NULL.

However, our atomic_setup function will overwrite that pointer without
putting the reference back leading to a memory leak.

Since the commit is only relevant during the atomic commit process, it
doesn't make sense to duplicate the reference to the commit anyway.
Let's remove it.

Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-6-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: kms: Clear the HVS FIFO commit pointer once done

commit d134c5ff71c7f2320fc7997f2fbbdedf0c76889a upstream.

Commit 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a
commit") introduced a wait on the previous commit done on a given HVS
FIFO.

However, we never cleared that pointer once done. Since
drm_crtc_commit_put can free the drm_crtc_commit structure directly if
we were the last user, this means that it can lead to a use-after free
if we were to duplicate the state, and that stale pointer would even be
copied to the new state.

Set the pointer to NULL once we're done with the wait so that we don't
carry over a pointer to a free'd structure.

Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-5-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: kms: Add missing drm_crtc_commit_put

commit 049cfff8d53a30cae3349ff71a4c01b7d9981bc2 upstream.

Commit 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a
commit") introduced a global state for the HVS, with each FIFO storing
the current CRTC commit so that we can properly synchronize commits.

However, the refcounting was off and we thus ended up leaking the
drm_crtc_commit structure every commit. Add a drm_crtc_commit_put to
prevent the leakage.

Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-4-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: kms: Fix return code check

commit f927767978d201d4ac023fcd797adbb963a6565d upstream.

The HVS global state functions return an error pointer, but in most
cases we check if it's NULL, possibly resulting in an invalid pointer
dereference.

Fixes: 9ec03d7f1ed3 ("drm/vc4: kms: Wait on previous FIFO users before a commit")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-3-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vc4: kms: Wait for the commit before increasing our clock rate

commit 0c980a006d3fbee86c4d0698f66d6f5381831787 upstream.

Several DRM/KMS atomic commits can run in parallel if they affect
different CRTC. These commits share the global HVS state, so we have
some code to make sure we run commits in sequence. This synchronization
code is one of the first thing that runs in vc4_atomic_commit_tail().

Another constraints we have is that we need to make sure the HVS clock
gets a boost during the commit. That code relies on clk_set_min_rate and
will remove the old minimum and set a new one. We also need another,
temporary, minimum for the duration of the commit.

The algorithm is thus to set a temporary minimum, drop the previous
one, do the commit, and finally set the minimum for the current mode.

However, the part that sets the temporary minimum and drops the older
one runs before the commit synchronization code.

Thus, under the proper conditions, we can end up mixing up the minimums
and ending up with the wrong one for our current step.

To avoid it, let's move the clock setup in the protected section.

Fixes: d7d96c00e585 ("drm/vc4: hvs: Boost the core clock during modeset")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-by: Jian-Hong Pan <jhp@endlessos.org>
Link: https://lore.kernel.org/r/20211117094527.146275-2-maxime@cerno.tech
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm: Do hw_init() before capturing GPU state

commit e4840d537c2c6b1189d4de16ee0f4820e069dcea upstream.

In particular, we need to ensure all the necessary blocks are switched
to 64b mode (a5xx+) otherwise the high bits of the address of the BO to
snapshot state into will be ignored, resulting in:

  *** gpu fault: ttbr0=0000000000000000 iova=0000000000012000 dir=READ type=TRANSLATION source=CP (0,0,0,0)
  platform 506a000.gmu: [drm:a6xx_gmu_set_oob] *ERROR* Timeout waiting for GMU OOB set BOOT_SLUMBER: 0x0

Fixes: 4f776f4511c7 ("drm/msm/gpu: Convert the GPU show function to use the GPU state")
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20211108180122.487859-1-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/msm/a6xx: Allocate enough space for GMU registers

commit b4d25abf9720b69a03465b09d0d62d1998ed6708 upstream.

In commit 142639a52a01 ("drm/msm/a6xx: fix crashstate capture for
A650") we changed a6xx_get_gmu_registers() to read 3 sets of
registers. Unfortunately, we didn't change the memory allocation for
the array. That leads to a KASAN warning (this was on the chromeos-5.4
kernel, which has the problematic commit backported to it):

  BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430
  Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209
  CPU: 5 PID: 209 Comm: A618-worker Tainted: G        W         5.4.156-lockdep #22
  Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT)
  Call trace:
   dump_backtrace+0x0/0x248
   show_stack+0x20/0x2c
   dump_stack+0x128/0x1ec
   print_address_description+0x88/0x4a0
   __kasan_report+0xfc/0x120
   kasan_report+0x10/0x18
   __asan_report_store8_noabort+0x1c/0x24
   _a6xx_get_gmu_registers+0x144/0x430
   a6xx_gpu_state_get+0x330/0x25d4
   msm_gpu_crashstate_capture+0xa0/0x84c
   recover_worker+0x328/0x838
   kthread_worker_fn+0x32c/0x574
   kthread+0x2dc/0x39c
   ret_from_fork+0x10/0x18

  Allocated by task 209:
   __kasan_kmalloc+0xfc/0x1c4
   kasan_kmalloc+0xc/0x14
   kmem_cache_alloc_trace+0x1f0/0x2a0
   a6xx_gpu_state_get+0x164/0x25d4
   msm_gpu_crashstate_capture+0xa0/0x84c
   recover_worker+0x328/0x838
   kthread_worker_fn+0x32c/0x574
   kthread+0x2dc/0x39c
   ret_from_fork+0x10/0x18

Fixes: 142639a52a01 ("drm/msm/a6xx: fix crashstate capture for A650")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20211103153049.1.Idfa574ccb529d17b69db3a1852e49b580132035c@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: Keep smc_close_final rc during active close

commit 00e158fb91dfaff3f94746f260d11f1a4853506e upstream.

When smc_close_final() returns error, the return code overwrites by
kernel_sock_shutdown() in smc_close_active(). The return code of
smc_close_final() is more important than kernel_sock_shutdown(), and it
will pass to userspace directly.

Fix it by keeping both return codes, if smc_close_final() raises an
error, return it or kernel_sock_shutdown()'s.

Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes: 606a63c9783a ("net/smc: Ensure the active closing peer first closes clcsock")
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/rds: correct socket tunable error in rds_tcp_tune()

commit 19f36edf14bcdb783aef3af8217df96f76a8ce34 upstream.

Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.

Fixes: c6a58ffed536 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket")
Signed-off-by: William Kucharski <william.kucharski@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: fix wrong list_del in smc_lgr_cleanup_early

commit 789b6cc2a5f9123b9c549b886fdc47c865cfe0ba upstream.

smc_lgr_cleanup_early() meant to delete the link
group from the link group list, but it deleted
the list head by mistake.

This may cause memory corruption since we didn't
remove the real link group from the list and later
memseted the link group structure.
We got a list corruption panic when testing:

[  231.277259] list_del corruption. prev->next should be ffff8881398a8000, but was 0000000000000000
[  231.278222] ------------[ cut here ]------------
[  231.278726] kernel BUG at lib/list_debug.c:53!
[  231.279326] invalid opcode: 0000 [#1] SMP NOPTI
[  231.279803] CPU: 0 PID: 5 Comm: kworker/0:0 Not tainted 5.10.46+ #435
[  231.280466] Hardware name: Alibaba Cloud ECS, BIOS 8c24b4c 04/01/2014
[  231.281248] Workqueue: events smc_link_down_work
[  231.281732] RIP: 0010:__list_del_entry_valid+0x70/0x90
[  231.282258] Code: 4c 60 82 e8 7d cc 6a 00 0f 0b 48 89 fe 48 c7 c7 88 4c
60 82 e8 6c cc 6a 00 0f 0b 48 89 fe 48 c7 c7 c0 4c 60 82 e8 5b cc 6a 00 <0f>
0b 48 89 fe 48 c7 c7 00 4d 60 82 e8 4a cc 6a 00 0f 0b cc cc cc
[  231.284146] RSP: 0018:ffffc90000033d58 EFLAGS: 00010292
[  231.284685] RAX: 0000000000000054 RBX: ffff8881398a8000 RCX: 0000000000000000
[  231.285415] RDX: 0000000000000001 RSI: ffff88813bc18040 RDI: ffff88813bc18040
[  231.286141] RBP: ffffffff8305ad40 R08: 0000000000000003 R09: 0000000000000001
[  231.286873] R10: ffffffff82803da0 R11: ffffc90000033b90 R12: 0000000000000001
[  231.287606] R13: 0000000000000000 R14: ffff8881398a8000 R15: 0000000000000003
[  231.288337] FS:  0000000000000000(0000) GS:ffff88813bc00000(0000) knlGS:0000000000000000
[  231.289160] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  231.289754] CR2: 0000000000e72058 CR3: 000000010fa96006 CR4: 00000000003706f0
[  231.290485] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  231.291211] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  231.291940] Call Trace:
[  231.292211]  smc_lgr_terminate_sched+0x53/0xa0
[  231.292677]  smc_switch_conns+0x75/0x6b0
[  231.293085]  ? update_load_avg+0x1a6/0x590
[  231.293517]  ? ttwu_do_wakeup+0x17/0x150
[  231.293907]  ? update_load_avg+0x1a6/0x590
[  231.294317]  ? newidle_balance+0xca/0x3d0
[  231.294716]  smcr_link_down+0x50/0x1a0
[  231.295090]  ? __wake_up_common_lock+0x77/0x90
[  231.295534]  smc_link_down_work+0x46/0x60
[  231.295933]  process_one_work+0x18b/0x350

Fixes: a0a62ee15a829 ("net/smc: separate locks for SMCD and SMCR link group lists")
Signed-off-by: Dust Li <dust.li@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: convert fib_num_tclassid_users to atomic_t

commit 213f5f8f31f10aa1e83187ae20fb7fa4e626b724 upstream.

Before commit faa041a40b9f ("ipv4: Create cleanup helper for fib_nh")
changes to net->ipv4.fib_num_tclassid_users were protected by RTNL.

After the change, this is no longer the case, as free_fib_info_rcu()
runs after rcu grace period, without rtnl being held.

Fixes: faa041a40b9f ("ipv4: Create cleanup helper for fib_nh")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: annotate data-races on txq->xmit_lock_owner

commit 7a10d8c810cfad3e79372d7d1c77899d86cd6662 upstream.

syzbot found that __dev_queue_xmit() is reading txq->xmit_lock_owner
without annotations.

No serious issue there, let's document what is happening there.

BUG: KCSAN: data-race in __dev_queue_xmit / __dev_queue_xmit

write to 0xffff888139d09484 of 4 bytes by interrupt on cpu 0:
 __netif_tx_unlock include/linux/netdevice.h:4437 [inline]
 __dev_queue_xmit+0x948/0xf70 net/core/dev.c:4229
 dev_queue_xmit_accel+0x19/0x20 net/core/dev.c:4265
 macvlan_queue_xmit drivers/net/macvlan.c:543 [inline]
 macvlan_start_xmit+0x2b3/0x3d0 drivers/net/macvlan.c:567
 __netdev_start_xmit include/linux/netdevice.h:4987 [inline]
 netdev_start_xmit include/linux/netdevice.h:5001 [inline]
 xmit_one+0x105/0x2f0 net/core/dev.c:3590
 dev_hard_start_xmit+0x72/0x120 net/core/dev.c:3606
 sch_direct_xmit+0x1b2/0x7c0 net/sched/sch_generic.c:342
 __dev_xmit_skb+0x83d/0x1370 net/core/dev.c:3817
 __dev_queue_xmit+0x590/0xf70 net/core/dev.c:4194
 dev_queue_xmit+0x13/0x20 net/core/dev.c:4259
 neigh_hh_output include/net/neighbour.h:511 [inline]
 neigh_output include/net/neighbour.h:525 [inline]
 ip6_finish_output2+0x995/0xbb0 net/ipv6/ip6_output.c:126
 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
 ip6_finish_output+0x444/0x4c0 net/ipv6/ip6_output.c:201
 NF_HOOK_COND include/linux/netfilter.h:296 [inline]
 ip6_output+0x10e/0x210 net/ipv6/ip6_output.c:224
 dst_output include/net/dst.h:450 [inline]
 NF_HOOK include/linux/netfilter.h:307 [inline]
 ndisc_send_skb+0x486/0x610 net/ipv6/ndisc.c:508
 ndisc_send_rs+0x3b0/0x3e0 net/ipv6/ndisc.c:702
 addrconf_rs_timer+0x370/0x540 net/ipv6/addrconf.c:3898
 call_timer_fn+0x2e/0x240 kernel/time/timer.c:1421
 expire_timers+0x116/0x240 kernel/time/timer.c:1466
 __run_timers+0x368/0x410 kernel/time/timer.c:1734
 run_timer_softirq+0x2e/0x60 kernel/time/timer.c:1747
 __do_softirq+0x158/0x2de kernel/softirq.c:558
 __irq_exit_rcu kernel/softirq.c:636 [inline]
 irq_exit_rcu+0x37/0x70 kernel/softirq.c:648
 sysvec_apic_timer_interrupt+0x3e/0xb0 arch/x86/kernel/apic/apic.c:1097
 asm_sysvec_apic_timer_interrupt+0x12/0x20

read to 0xffff888139d09484 of 4 bytes by interrupt on cpu 1:
 __dev_queue_xmit+0x5e3/0xf70 net/core/dev.c:4213
 dev_queue_xmit_accel+0x19/0x20 net/core/dev.c:4265
 macvlan_queue_xmit drivers/net/macvlan.c:543 [inline]
 macvlan_start_xmit+0x2b3/0x3d0 drivers/net/macvlan.c:567
 __netdev_start_xmit include/linux/netdevice.h:4987 [inline]
 netdev_start_xmit include/linux/netdevice.h:5001 [inline]
 xmit_one+0x105/0x2f0 net/core/dev.c:3590
 dev_hard_start_xmit+0x72/0x120 net/core/dev.c:3606
 sch_direct_xmit+0x1b2/0x7c0 net/sched/sch_generic.c:342
 __dev_xmit_skb+0x83d/0x1370 net/core/dev.c:3817
 __dev_queue_xmit+0x590/0xf70 net/core/dev.c:4194
 dev_queue_xmit+0x13/0x20 net/core/dev.c:4259
 neigh_resolve_output+0x3db/0x410 net/core/neighbour.c:1523
 neigh_output include/net/neighbour.h:527 [inline]
 ip6_finish_output2+0x9be/0xbb0 net/ipv6/ip6_output.c:126
 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline]
 ip6_finish_output+0x444/0x4c0 net/ipv6/ip6_output.c:201
 NF_HOOK_COND include/linux/netfilter.h:296 [inline]
 ip6_output+0x10e/0x210 net/ipv6/ip6_output.c:224
 dst_output include/net/dst.h:450 [inline]
 NF_HOOK include/linux/netfilter.h:307 [inline]
 ndisc_send_skb+0x486/0x610 net/ipv6/ndisc.c:508
 ndisc_send_rs+0x3b0/0x3e0 net/ipv6/ndisc.c:702
 addrconf_rs_timer+0x370/0x540 net/ipv6/addrconf.c:3898
 call_timer_fn+0x2e/0x240 kernel/time/timer.c:1421
 expire_timers+0x116/0x240 kernel/time/timer.c:1466
 __run_timers+0x368/0x410 kernel/time/timer.c:1734
 run_timer_softirq+0x2e/0x60 kernel/time/timer.c:1747
 __do_softirq+0x158/0x2de kernel/softirq.c:558
 __irq_exit_rcu kernel/softirq.c:636 [inline]
 irq_exit_rcu+0x37/0x70 kernel/softirq.c:648
 sysvec_apic_timer_interrupt+0x8d/0xb0 arch/x86/kernel/apic/apic.c:1097
 asm_sysvec_apic_timer_interrupt+0x12/0x20
 kcsan_setup_watchpoint+0x94/0x420 kernel/kcsan/core.c:443
 folio_test_anon include/linux/page-flags.h:581 [inline]
 PageAnon include/linux/page-flags.h:586 [inline]
 zap_pte_range+0x5ac/0x10e0 mm/memory.c:1347
 zap_pmd_range mm/memory.c:1467 [inline]
 zap_pud_range mm/memory.c:1496 [inline]
 zap_p4d_range mm/memory.c:1517 [inline]
 unmap_page_range+0x2dc/0x3d0 mm/memory.c:1538
 unmap_single_vma+0x157/0x210 mm/memory.c:1583
 unmap_vmas+0xd0/0x180 mm/memory.c:1615
 exit_mmap+0x23d/0x470 mm/mmap.c:3170
 __mmput+0x27/0x1b0 kernel/fork.c:1113
 mmput+0x3d/0x50 kernel/fork.c:1134
 exit_mm+0xdb/0x170 kernel/exit.c:507
 do_exit+0x608/0x17a0 kernel/exit.c:819
 do_group_exit+0xce/0x180 kernel/exit.c:929
 get_signal+0xfc3/0x1550 kernel/signal.c:2852
 arch_do_signal_or_restart+0x8c/0x2e0 arch/x86/kernel/signal.c:868
 handle_signal_work kernel/entry/common.c:148 [inline]
 exit_to_user_mode_loop kernel/entry/common.c:172 [inline]
 exit_to_user_mode_prepare+0x113/0x190 kernel/entry/common.c:207
 __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
 syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:300
 do_syscall_64+0x50/0xd0 arch/x86/entry/common.c:86
 entry_SYSCALL_64_after_hwframe+0x44/0xae

value changed: 0x00000000 -> 0xffffffff

Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 28712 Comm: syz-executor.0 Tainted: G        W         5.16.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Link: https://lore.kernel.org/r/20211130170155.2331929-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

octeontx2-af: Fix a memleak bug in rvu_mbox_init()

commit e07a097b4986afb8f925d0bb32612e1d3e88ce15 upstream.

In rvu_mbox_init(), mbox_regions is not freed or passed out
under the switch-default region, which could lead to a memory leak.

Fix this bug by changing 'return err' to 'goto free_regions'.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_OCTEONTX2_AF=y show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: 98c561116360 (“octeontx2-af: cn10k: Add mbox support for CN10K platform”)
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130165039.192426-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dpaa2-eth: destroy workqueue at the end of remove function

commit f4a8adbfe4841491b60c14fe610571e1422359f9 upstream.

The commit c55211892f46 ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.

Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.

Fixes: c55211892f46 ("dpaa2-eth: support PTP Sync packet one-step timestamping")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: marvell: mvpp2: Fix the computation of shared CPUs

commit b83f5ac7d922e69a109261f5f940eebbd4e514c4 upstream.

'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.

Use 'bitmap_set()' instead in order not to set unexpected bits.

Fixes: e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: usb: lan78xx: lan78xx_phy_init(): use PHY_POLL instead of "0" if no IRQ is available

commit 817b653160db9852d5a0498a31f047e18ce27e5b upstream.

On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.

Fixes: cc89c323a30e ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: Avoid DMA_CHAN_CONTROL write if no Split Header support

commit f8e7dfd6fdabb831846ab1970a875746559d491b upstream.

The driver assumes that split headers can be enabled/disabled without
stopping/starting the device, so it writes DMA_CHAN_CONTROL from
stmmac_set_features().  However, on my system (IP v5.10a without Split
Header support), simply writing DMA_CHAN_CONTROL when DMA is running
(for example, with the commands below) leads to a TX watchdog timeout.

 host$ socat TCP-LISTEN:1024,fork,reuseaddr - &
 device$ ethtool -K eth0 tso off
 device$ ethtool -K eth0 tso on
 device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024
 <tx watchdog timeout>

Note that since my IP is configured without Split Header support, the
driver always just reads and writes the same value to the
DMA_CHAN_CONTROL register.

I don't have access to any platforms with Split Header support so I
don't know if these writes to the DMA_CHAN_CONTROL while DMA is running
actually work properly on such systems.  I could not find anything in
the databook that says that DMA_CHAN_CONTROL should not be written when
the DMA is running.

But on systems without Split Header support, there is in any case no
need to call enable_sph() in stmmac_set_features() at all since SPH can
never be toggled, so we can avoid the watchdog timeout there by skipping
this call.

Fixes: 8c6fc097a2f4acf ("net: stmmac: gmac4+: Add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: intel-dsp-config: add quirk for CML devices based on ES8336 codec

commit ae26c08e6c8071ba8febb0c7c0829da96c75248c upstream.

We've added quirks for ESS8336 but missed CML, add quirks for both LP
and H versions.

BugLink: https://github.com/thesofproject/linux/issues/3248
Fixes: 9d36ceab9415 ("ALSA: intel-dsp-config: add quirk for APL/GLK/TGL devices based on ES8336 codec")
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20211122232254.23362-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rxrpc: Fix rxrpc_local leak in rxrpc_lookup_peer()

commit beacff50edbd6c9659a6f15fc7f6126909fade29 upstream.

Need to call rxrpc_put_local() for peer candidate before kfree() as it
holds a ref to rxrpc_local.

[DH: v2: Changed to abstract the peer freeing code out into a function]

Fixes: 9ebeddef58c4 ("rxrpc: rxrpc_peer needs to hold a ref on the rxrpc_local record")
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/all/20211121041608.133740-2-eiichi.tsukata@nutanix.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rxrpc: Fix rxrpc_peer leak in rxrpc_look_up_bundle()

commit ca77fba821351190777b236ce749d7c4d353102e upstream.

Need to call rxrpc_put_peer() for bundle candidate before kfree() as it
holds a ref to rxrpc_peer.

[DH: v2: Changed to abstract out the bundle freeing code into a function]

Fixes: 245500d853e9 ("rxrpc: Rewrite the client connection manager")
Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20211121041608.133740-1-eiichi.tsukata@nutanix.com/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix kcontrol put callback in AHUB

commit a4e37950c9e9b126f9cbee79b8ab94a94646dcf1 upstream.

The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the AHUB driver accordingly.

Fixes: 16e1bcc2caf4 ("ASoC: tegra: Add Tegra210 based AHUB driver")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-12-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix kcontrol put callback in DSPK

commit d6202a57e79d102271d38c34481fedc9d4c79694 upstream.

The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the DSPK driver accordingly.

Fixes: 327ef6470266 ("ASoC: tegra: Add Tegra186 based DSPK driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-11-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix kcontrol put callback in DMIC

commit a347dfa10262fa0a10e2b1970ea0194e3d4a3251 upstream.

The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the DMIC driver accordingly.

Fixes: 8c8ff982e9e2 ("ASoC: tegra: Add Tegra210 based DMIC driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-10-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix kcontrol put callback in I2S

commit f21a9df3f7cb0005947679d7b9237c90574e229a upstream.

The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the I2S driver accordingly.

Fixes: c0bfa98349d1 ("ASoC: tegra: Add Tegra210 based I2S driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-9-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix kcontrol put callback in ADMAIF

commit e2b87a18a60c02d0dcd1de801d669587e516cc4d upstream.

The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the ADMAIF driver accordingly.

Fixes: f74028e159bb ("ASoC: tegra: Add Tegra210 based ADMAIF driver")
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-8-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix wrong value type in DSPK

commit 3aa0d5c8bb3f5ef622ec2764823f551a1f630711 upstream.

The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.

Fixes: 327ef6470266 ("ASoC: tegra: Add Tegra186 based DSPK driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-5-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix wrong value type in DMIC

commit 559d234569a998a4004de1bd1f12da5487fb826e upstream.

The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.

Fixes: 8c8ff982e9e2 ("ASoC: tegra: Add Tegra210 based DMIC driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-4-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix wrong value type in I2S

commit 8a2c2fa0c5331445c801e9241f2bb4e0e2a895a8 upstream.

The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.

Fixes: c0bfa98349d1 ("ASoC: tegra: Add Tegra210 based I2S driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-3-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tegra: Fix wrong value type in ADMAIF

commit 884c6cb3b7030f75c46e55b9e625d2372708c306 upstream.

The enum controls are expected to use enumerated value type.
Update relevant references in control get/put callbacks.

Fixes: f74028e159bb ("ASoC: tegra: Add Tegra210 based ADMAIF driver")
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/1637219231-406-2-git-send-email-spujar@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mt76: mt7915: fix NULL pointer dereference in mt7915_get_phy_mode

commit 6e53d6d26920d5221d3f4d4f5ffdd629ea69aa5c upstream.

Fix the following NULL pointer dereference in mt7915_get_phy_mode
routine adding an ibss interface to the mt7915 driver.

[  101.137097] wlan0: Trigger new scan to find an IBSS to join
[  102.827039] wlan0: Creating new IBSS network, BSSID 26:a4:50:1a:6e:69
[  103.064756] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[  103.073670] Mem abort info:
[  103.076520]   ESR = 0x96000005
[  103.079614]   EC = 0x25: DABT (current EL), IL = 32 bits
[  103.084934]   SET = 0, FnV = 0
[  103.088042]   EA = 0, S1PTW = 0
[  103.091215] Data abort info:
[  103.094104]   ISV = 0, ISS = 0x00000005
[  103.098041]   CM = 0, WnR = 0
[  103.101044] user pgtable: 4k pages, 39-bit VAs, pgdp=00000000460b1000
[  103.107565] [0000000000000000] pgd=0000000000000000, p4d=0000000000000000, pud=0000000000000000
[  103.116590] Internal error: Oops: 96000005 [#1] SMP
[  103.189066] CPU: 1 PID: 333 Comm: kworker/u4:3 Not tainted 5.10.75 #0
[  103.195498] Hardware name: MediaTek MT7622 RFB1 board (DT)
[  103.201124] Workqueue: phy0 ieee80211_iface_work [mac80211]
[  103.206695] pstate: 20000005 (nzCv daif -PAN -UAO -TCO BTYPE=--)
[  103.212705] pc : mt7915_get_phy_mode+0x68/0x120 [mt7915e]
[  103.218103] lr : mt7915_mcu_add_bss_info+0x11c/0x760 [mt7915e]
[  103.223927] sp : ffffffc011cdb9e0
[  103.227235] x29: ffffffc011cdb9e0 x28: ffffff8006563098
[  103.232545] x27: ffffff8005f4da22 x26: ffffff800685ac40
[  103.237855] x25: 0000000000000001 x24: 000000000000011f
[  103.243165] x23: ffffff8005f4e260 x22: ffffff8006567918
[  103.248475] x21: ffffff8005f4df80 x20: ffffff800685ac58
[  103.253785] x19: ffffff8006744400 x18: 0000000000000000
[  103.259094] x17: 0000000000000000 x16: 0000000000000001
[  103.264403] x15: 000899c3a2d9d2e4 x14: 000899bdc3c3a1c8
[  103.269713] x13: 0000000000000000 x12: 0000000000000000
[  103.275024] x11: ffffffc010e30c20 x10: 0000000000000000
[  103.280333] x9 : 0000000000000050 x8 : ffffff8006567d88
[  103.285642] x7 : ffffff8006563b5c x6 : ffffff8006563b44
[  103.290952] x5 : 0000000000000002 x4 : 0000000000000001
[  103.296262] x3 : 0000000000000001 x2 : 0000000000000001
[  103.301572] x1 : 0000000000000000 x0 : 0000000000000011
[  103.306882] Call trace:
[  103.309328]  mt7915_get_phy_mode+0x68/0x120 [mt7915e]
[  103.314378]  mt7915_bss_info_changed+0x198/0x200 [mt7915e]
[  103.319941]  ieee80211_bss_info_change_notify+0x128/0x290 [mac80211]
[  103.326360]  __ieee80211_sta_join_ibss+0x308/0x6c4 [mac80211]
[  103.332171]  ieee80211_sta_create_ibss+0x8c/0x10c [mac80211]
[  103.337895]  ieee80211_ibss_work+0x3dc/0x614 [mac80211]
[  103.343185]  ieee80211_iface_work+0x388/0x3f0 [mac80211]
[  103.348495]  process_one_work+0x288/0x690
[  103.352499]  worker_thread+0x70/0x464
[  103.356157]  kthread+0x144/0x150
[  103.359380]  ret_from_fork+0x10/0x18
[  103.362952] Code: 394008c3 52800220 394000e4 7100007f (39400023)

Fixes: 37f4ca907c46 ("mt76: mt7915: register per-phy HE capabilities for each interface")
Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/ddae419a740f1fb9e48afd432035e9f394f512ee.1637239456.git.lorenzo@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: b53: Add SPI ID table

commit 88362ebfd7fb569c78d5cb507aa9d3c8fc203839 upstream.

Currently autoloading for SPI devices does not use the DT ID table, it
uses SPI modalises. Supporting OF modalises is going to be difficult if
not impractical, an attempt was made but has been reverted, so ensure
that module autoloading works for this driver by adding an id_table
listing the SPI IDs for everything.

Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: net: Correct case name

commit a05431b22be819d75db72ca3d44381d18a37b092 upstream.

ipv6_addr_bind/ipv4_addr_bind are function names. Previously, bind test
would not be run by default due to the wrong case names

Fixes: 34d0302ab861 ("selftests: Add ipv6 address bind tests to fcnal-test")
Fixes: 75b2b2b3db4c ("selftests: Add ipv4 address bind tests to fcnal-test")
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx4_en: Fix an use-after-free bug in mlx4_en_try_alloc_resources()

commit addad7643142f500080417dd7272f49b7a185570 upstream.

In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().

Fix this bug by adding a check of mlx4_en_copy_priv()

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.

Fixes: ec25bc04ed8e ("net/mlx4_en: Add resilience in low memory systems")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/mlx5e: IPsec: Fix Software parser inner l3 type setting in case of encapsulation

commit c65d638ab39034cbaa36773b980d28106cfc81fa upstream.

Current code wrongly uses the skb->protocol field which reflects the
outer l3 protocol to set the inner l3 type in Software Parser (SWP)
fields settings in the ethernet segment (eseg) in flows where inner
l3 exists like in Vxlan over ESP flow, the above method wrongly use
the outer protocol type instead of the inner one. thus breaking cases
where inner and outer headers have different protocols.

Fix by setting the inner l3 type in SWP according to the inner l3 ip
header version.

Fixes: 2ac9cfe78223 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Signed-off-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Maor Dickman <maord@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: fix warnings produced by kernel debug options

commit f5cecf1d4c5ff76172928bc32e99ca56a5ca2f56 upstream.

Fix warnings produced by:
- lockdep_assert_wiphy() in function reg_process_self_managed_hint(),
- wiphy_dereference() in function iwl_mvm_init_fw_regd().
Both function are expected to be called in critical section.

The warnings were discovered when running v5.15 kernel
with debug options enabled:

1)
Hardware name: Google Delbin/Delbin
RIP: 0010:reg_process_self_managed_hint+0x254/0x347 [cfg80211]
...
Call Trace:
regulatory_set_wiphy_regd_sync+0x3d/0xb0
iwl_mvm_init_mcc+0x49d/0x5a2
iwl_op_mode_mvm_start+0x1b58/0x2507
? iwl_mvm_reprobe_wk+0x94/0x94
_iwl_op_mode_start+0x146/0x1a3
iwl_opmode_register+0xda/0x13d
init_module+0x28/0x1000

2)
drivers/net/wireless/intel/iwlwifi/mvm/mac80211.c:263 suspicious rcu_dereference_protected() usage!
...
Hardware name: Google Delbin/Delbin, BIOS Google_Delbin
Call Trace:
dump_stack_lvl+0xb1/0xe6
iwl_mvm_init_fw_regd+0x2e7/0x379
iwl_mvm_init_mcc+0x2c6/0x5a2
iwl_op_mode_mvm_start+0x1b58/0x2507
? iwl_mvm_reprobe_wk+0x94/0x94
_iwl_op_mode_start+0x146/0x1a3
iwl_opmode_register+0xda/0x13d
init_module+0x28/0x100

Fixes: a05829a7222e ("cfg80211: avoid holding the RTNL when calling the driver")
Signed-off-by: Łukasz Bartosik <lb@semihalf.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211110215744.5487-1-lukasz.bartosik@semihalf.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: ftrace: add missing BTIs

commit 35b6b28e69985eafb20b3b2c7bd6eca452b56b53 upstream.

When branch target identifiers are in use, code reachable via an
indirect branch requires a BTI landing pad at the branch target site.

When building FTRACE_WITH_REGS atop patchable-function-entry, we miss
BTIs at the start start of the `ftrace_caller` and `ftrace_regs_caller`
trampolines, and when these are called from a module via a PLT (which
will use a `BR X16`), we will encounter a BTI failure, e.g.

| # insmod lkdtm.ko
| lkdtm: No crash points registered, enable through debugfs
| # echo function_graph > /sys/kernel/debug/tracing/current_tracer
| # cat /sys/kernel/debug/provoke-crash/DIRECT
| Unhandled 64-bit el1h sync exception on CPU0, ESR 0x34000001 -- BTI
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| pstate: 60400405 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=jc)
| pc : ftrace_caller+0x0/0x3c
| lr : lkdtm_debugfs_open+0xc/0x20 [lkdtm]
| sp : ffff800012e43b00
| x29: ffff800012e43b00 x28: 0000000000000000 x27: ffff800012e43c88
| x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000c171f200
| x23: ffff0000c27b1e00 x22: ffff0000c2265240 x21: ffff0000c23c8c30
| x20: ffff8000090ba380 x19: 0000000000000000 x18: 0000000000000000
| x17: 0000000000000000 x16: ffff80001002bb4c x15: 0000000000000000
| x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000900ff0
| x11: ffff0000c4166310 x10: ffff800012e43b00 x9 : ffff8000104f2384
| x8 : 0000000000000001 x7 : 0000000000000000 x6 : 000000000000003f
| x5 : 0000000000000040 x4 : ffff800012e43af0 x3 : 0000000000000001
| x2 : ffff8000090b0000 x1 : ffff0000c171f200 x0 : ffff0000c23c8c30
| Kernel panic - not syncing: Unhandled exception
| CPU: 0 PID: 174 Comm: cat Not tainted 5.16.0-rc2-dirty #3
| Hardware name: linux,dummy-virt (DT)
| Call trace:
|  dump_backtrace+0x0/0x1a4
|  show_stack+0x24/0x30
|  dump_stack_lvl+0x68/0x84
|  dump_stack+0x1c/0x38
|  panic+0x168/0x360
|  arm64_exit_nmi.isra.0+0x0/0x80
|  el1h_64_sync_handler+0x68/0xd4
|  el1h_64_sync+0x78/0x7c
|  ftrace_caller+0x0/0x3c
|  do_dentry_open+0x134/0x3b0
|  vfs_open+0x38/0x44
|  path_openat+0x89c/0xe40
|  do_filp_open+0x8c/0x13c
|  do_sys_openat2+0xbc/0x174
|  __arm64_sys_openat+0x6c/0xbc
|  invoke_syscall+0x50/0x120
|  el0_svc_common.constprop.0+0xdc/0x100
|  do_el0_svc+0x84/0xa0
|  el0_svc+0x28/0x80
|  el0t_64_sync_handler+0xa8/0x130
|  el0t_64_sync+0x1a0/0x1a4
| SMP: stopping secondary CPUs
| Kernel Offset: disabled
| CPU features: 0x0,00000f42,da660c5f
| Memory Limit: none
| ---[ end Kernel panic - not syncing: Unhandled exception ]---

Fix this by adding the required `BTI C`, as we only require these to be
reachable via BL for direct calls or BR X16/X17 for PLTs. For now, these
are open-coded in the function prologue, matching the style of the
`__hwasan_tag_mismatch` trampoline.

In future we may wish to consider adding a new SYM_CODE_START_*()
variant which has an implicit BTI.

When ftrace is built atop mcount, the trampolines are marked with
SYM_FUNC_START(), and so get an implicit BTI. We may need to change
these over to SYM_CODE_START() in future for RELIABLE_STACKTRACE, in
case we need to apply special care aroud the return address being
rewritten.

Fixes: 97fed779f2a6 ("arm64: bti: Provide Kconfig for kernel mode BTI")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20211129135709.2274019-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

siphash: use _unaligned version by default

commit f7e5b9bfa6c8820407b64eabc1f29c9a87e8993d upstream.

On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.

Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.

Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.

This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.

Link: https://lore.kernel.org/linux-arm-kernel/20181008211554.5355-4-ard.biesheuvel@linaro.org/
Link: https://lore.kernel.org/linux-crypto/CAK8P3a2KfmmGDbVHULWevB0hv71P2oi2ZCHEAqT=8dQfa0=cqQ@mail.gmail.com/
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2c956a60778c ("siphash: add cryptographically secure PRF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mpls: Fix notifications when deleting a device

commit 7d4741eacdefa5f0475431645b56baf00784df1f upstream.

There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop

All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.

Fixes: f8efb73c97e2 ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qlogic: qlcnic: Fix a NULL pointer dereference in qlcnic_83xx_add_rings()

commit e2dabc4f7e7b60299c20a36d6a7b24ed9bf8e572 upstream.

In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().

Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.

This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.

Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.

Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.

Fixes: 7f9664525f9c ("qlcnic: 83xx memory map and HW access routine")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Link: https://lore.kernel.org/r/20211130110848.109026-1-zhou1615@umn.edu
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: fix page frag corruption on page fault

commit dacb5d8875cc6cd3a553363b4d6f06760fcbe70c upstream.

Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.

The root cause is quite similar to the one addressed by
commit 20eb4f29b602 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.

The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.

The overall relevant stack trace looks like the following:

httpd 78268 [001] 3461630.850950:      probe:tcp_sendmsg_locked:
        ffffffff91461d91 tcp_sendmsg_locked+0x1
        ffffffff91462b57 tcp_sendmsg+0x27
        ffffffff9139814e sock_sendmsg+0x3e
        ffffffffc06dfe1d smb_send_kvec+0x28
        [...]
        ffffffffc06cfaf8 cifs_readpages+0x213
        ffffffff90e83c4b read_pages+0x6b
        ffffffff90e83f31 __do_page_cache_readahead+0x1c1
        ffffffff90e79e98 filemap_fault+0x788
        ffffffff90eb0458 __do_fault+0x38
        ffffffff90eb5280 do_fault+0x1a0
        ffffffff90eb7c84 __handle_mm_fault+0x4d4
        ffffffff90eb8093 handle_mm_fault+0xc3
        ffffffff90c74f6d __do_page_fault+0x1ed
        ffffffff90c75277 do_page_fault+0x37
        ffffffff9160111e page_fault+0x1e
        ffffffff9109e7b5 copyin+0x25
        ffffffff9109eb40 _copy_from_iter_full+0xe0
        ffffffff91462370 tcp_sendmsg_locked+0x5e0
        ffffffff91462370 tcp_sendmsg_locked+0x5e0
        ffffffff91462b57 tcp_sendmsg+0x27
        ffffffff9139815c sock_sendmsg+0x4c
        ffffffff913981f7 sock_write_iter+0x97
        ffffffff90f2cc56 do_iter_readv_writev+0x156
        ffffffff90f2dff0 do_iter_write+0x80
        ffffffff90f2e1c3 vfs_writev+0xa3
        ffffffff90f2e27c do_writev+0x5c
        ffffffff90c042bb do_syscall_64+0x5b
        ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65

The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.

v1 -> v2:
 - use a stricted sk_page_frag() check instead of reordering the
   code (Eric)

Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes: 5640f7685831 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

natsemi: xtensa: fix section mismatch warnings

commit b0f38e15979fa8851e88e8aa371367f264e7b6e9 upstream.

Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.

WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.

WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.

Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: linux-xtensa@linux-xtensa.org
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: cbus-gpio: set atomic transfer callback

commit b12764695c3fcade145890b67f82f8b139174cc7 upstream.

CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.

Fixes the following WARNING seen during Nokia N810 power down:

[  786.570617] reboot: Power down
[  786.573913] ------------[ cut here ]------------
[  786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[  786.587799] No atomic I2C transfer handler for 'i2c-2'

Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: stm32f7: stop dma transfer in case of NACK

commit 31b90a95ccbbb4b628578ac17e3b3cc8eeacfe31 upstream.

In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.

Fixes: 7ecc8cfde553 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i2c: stm32f7: recover the bus on access timeout

commit b933d1faf8fa30d16171bcff404e39c41b2a7c84 upstream.

When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.

Fixes: aeb068c57214 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>