Jaehoon Chung [Mon, 15 Oct 2012 19:10:31 +0000 (19:10 +0000)]
EXYNOS: mmc: support DesignWare Controller for Samsung-SoC
Support DesignWare MMC Controller for Samsung Specific.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rajeshawari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Pantelis Antoniou [Wed, 28 Nov 2012 02:43:54 +0000 (02:43 +0000)]
Remove obsolete header file
usbdescriptors.h conflicts with linux/usb/ch9.h
Remove it.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Tom Rini [Mon, 26 Nov 2012 21:53:33 +0000 (14:53 -0700)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Benoît Thébaudeau [Fri, 16 Nov 2012 19:20:54 +0000 (20:20 +0100)]
nand: Add torture feature
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Benoît Thébaudeau [Mon, 5 Nov 2012 10:16:15 +0000 (10:16 +0000)]
nand: Fix nand_erase_opts() offset check
NAND Flash is erased by blocks, not by pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Benoît Thébaudeau [Mon, 5 Nov 2012 10:15:46 +0000 (10:15 +0000)]
nand: Clean up nand_util
This patch cleans up nand_util.c:
- Fix tabs.
- Fix typos.
- Remove space character before opening parenthesis in function calls.
- Fix comments.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Joe Hershberger [Mon, 5 Nov 2012 06:46:31 +0000 (06:46 +0000)]
nand: Move the sub-page read support enable to a flag
Use a flag instead of a hard-coded macro so that sub-page reads can be
enabled in other cases (such as on-die ecc).
This is the same as
a5ff4f102937a3492bca4a9ff0c341d78813414c in Linux
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Prabhakar Kushwaha [Wed, 12 Sep 2012 22:26:05 +0000 (22:26 +0000)]
driver/mtd:IFC NAND:Initialise internal SRAM before any write
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[scottwood@freescale.com: fix fsl_ifc_sram_init prototype]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Karl O. Pinc [Fri, 3 Aug 2012 05:57:21 +0000 (05:57 +0000)]
README: Reference nand monitor commands in U-Boot README
Reference nand monitor commands in U-Boot README
Signed-off-by: Karl O. Pinc <kop@meme.com>
Scott Wood [Fri, 2 Nov 2012 23:41:35 +0000 (18:41 -0500)]
nand/fsl: add NAND_NO_SUBPAGE_WRITE to eLBC and IFC drivers
These controllers can only do hardware ECC on full page transfers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Fri, 12 Oct 2012 23:02:24 +0000 (18:02 -0500)]
powerpc/mpc85xx/p2020rdb-pca: Use L2 SRAM for SPL boot
This allows DDR configuration to be deferred to the final U-Boot image,
which is able to make use of SPD data. The SPL itself cannot use SPD due
to code size constraints. It previously used fixed register values for
DDR configuration, and those values did not work on the p2020rdb-pca
board I tested with. It's possible that different revisions of the board
require different settings. Using SPD eliminates that problem.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Wed, 3 Oct 2012 00:35:18 +0000 (19:35 -0500)]
powerpc/mpc85xx/p1_p2_rdb_pc: clean up memory map
- Sort by address, and fix column alignment
- Don't label things as localbus that aren't. Instead, put chipselect
info at the end of the description for localbus windows. Note that
NAND/NOR have their chipselects swapped when booting from NAND, and CS2
can be either PMC or VSC7385 depending on hwconfig.
- Shrink NAND to the 32K that's actually mapped in the localbus
- Assign an address and size to L2 SRAM. Remove the similarly named
but unintelligible "L2 SDRAM(REV.)".
- Remove the untrue comment about L1 stack being mapped with TLB0.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 21 Sep 2012 21:31:00 +0000 (16:31 -0500)]
powerpc/mpc85xx/p1_p2_rdb_pc: convert from nand_spl to new spl
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 21 Sep 2012 23:35:27 +0000 (18:35 -0500)]
spl/nand: config symbol documentation
Document parameters used for specifying the NAND image to be loaded.
Also fix the definition of CONFIG_SPL_NAND_SIMPLE -- it's only
nand_spl_simple.c, not the entire nand directory. The word "simple" is
there for a reason. :-)
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: updated for makefile changes earlier in patchset
Scott Wood [Fri, 21 Sep 2012 00:09:07 +0000 (19:09 -0500)]
spl/nand: introduce CONFIG_SPL_NAND_DRIVERS, _BASE, and _ECC.
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver. Some SPLs need software ECC but others can't
fit it.
All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
Scott Wood [Fri, 21 Sep 2012 00:05:12 +0000 (19:05 -0500)]
powerpc/mpc85xx/p1_p2_rdb_pc: new SPL support
Introduces CONFIG_SPL_RELOC_TEXT_BASE and CONFIG_SPL_RELOC_STACK.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 21 Sep 2012 00:02:18 +0000 (19:02 -0500)]
spl/85xx: new SPL support
Update CONFIG_RAMBOOT and CONFIG_NAND_SPL references to accept CONFIG_SPL
and CONFIG_SPL_BUILD, respectively. CONFIG_NAND_SPL can be removed once
the last mpc85xx nand_spl target is gone.
CONFIG_RAMBOOT will need to remain for other use cases, but it doesn't
seem right to overload it for meaning SPL as well as nand_spl does. Even
if it's somewhat appropriate for the main u-boot, the SPL itself isn't
(necessarily) ramboot, and we don't have separate configs for SPL and
main u-boot. It was also inconsistent, as other platforms such as
mpc83xx didn't use CONFIG_RAMBOOT in this way.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Thu, 20 Sep 2012 21:35:21 +0000 (16:35 -0500)]
spl/powerpc: introduce CONFIG_SPL_INIT_MINIMAL
cpu_init_nand.c is renamed to spl_minimal.c as it is not really NAND-specific.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: factor out START, and change cpu_init_nand.c to spl_minimal.c
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Tue, 25 Sep 2012 23:17:45 +0000 (18:17 -0500)]
powerpc/mpc85xx: consistently use COBJS-y
A subsequent patch will conditionalize some of the files that are
currently unconditional.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Thu, 20 Sep 2012 21:35:21 +0000 (16:35 -0500)]
spl/mpc85xx: rename cpu_init_nand.c to spl_minimal.c
There is nothing really NAND-specific about this file.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Wed, 19 Sep 2012 22:56:39 +0000 (17:56 -0500)]
spl: include resetvec and lib8xxx
The toplevel makefile hardcodes this stuff, so spl/Makefile needs to as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Scott Wood [Sat, 18 Aug 2012 00:46:29 +0000 (19:46 -0500)]
spl/mpc85xx: move udelay to cpu code
It applies to non-Freescale 85xx boards as well as Freescale boards,
so it doesn't belong in board/freescale. Plus, it needs to come out
of nand_spl if it's to be used by the new SPL.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 17 Aug 2012 21:17:50 +0000 (16:17 -0500)]
powerpc/mpc8xxx: move LAW code into arch/powerpc/cpu/mpc8xxx
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Thu, 20 Sep 2012 23:34:49 +0000 (18:34 -0500)]
powerpc/mpc85xx: fix TLB alignment
In the RAMBOOT/SPL case we were creating a TLB entry starting at
CONFIG_SYS_MONITOR_BASE, and just hoping that the base was properly
aligned for the TLB entry size. This turned out to not be the case
with NAND SPL because the main U-Boot starts at an offset into the image
in order to skip the SPL itself.
Fix the TLB entry to always start at a proper alignment. We still assume that
CONFIG_SYS_MONITOR_BASE doesn't start immediately before a large-page boundary
thus requiring multiple TLB entries.
Signed-off-by: Scott Wood <scottwood@frescale.com>
Cc: Andy Fleming <afleming@freescale.com>
Scott Wood [Fri, 21 Sep 2012 00:10:01 +0000 (19:10 -0500)]
powerpc: change .fixup test to a GCC version test
This was introduced by commit
244615197469dd6fe75ae082f38424b97c79aeaf, but it
fails in a minimal SPL build where the only thing in arch/powerpc/lib is
cache.c, which apparently doesn't generate any fixup records.
The problem is reported to occur with GCC 3.x, so insist on GCC 4.0 or newer.
Patterned after checkthumb as suggested by Tom Rini.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Tom Rini <trini@ti.com>
--
v2: test gcc version instead of testing nothing
Scott Wood [Fri, 21 Sep 2012 21:27:32 +0000 (16:27 -0500)]
spl: introduce CONFIG_SPL_TARGET
Currently the SPL target is specified in a CPU-specific makefile
fragment. While some targets may need something more complicated than a
simple target name, targets which don't need this shouldn't have to provide a makefile fragment just for this.
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: Removed default target as it's been pointed out to me how existing platforms
cause the SPL to be built.
Scott Wood [Wed, 19 Sep 2012 22:45:41 +0000 (17:45 -0500)]
spl: rename u-boot-pad.bin to u-boot-with-spl.bin
Signed-off-by: Scott Wood <scottwood@freescale.com>
José Miguel Gonçalves [Wed, 19 Sep 2012 01:25:26 +0000 (01:25 +0000)]
Add u-boot-pad.bin target to the Makefile
Samsung's S3C24XX SoCs need this in order to generate a binary image
with a padded SPL concatenated with U-Boot.
Signed-off-by: José Miguel Gonçalves <jose.goncalves@inov.pt>
[scottwood@freescale.com: fixed prereq of u-boot.ubl]
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: Removed spl/ prefix from u-boot.ubl prerequisite.
Scott Wood [Tue, 30 Oct 2012 00:00:41 +0000 (19:00 -0500)]
powerpc/mpc85xx: add comma before "already enabled"
Now outputs like this:
L2: 512 KB already enabled, moving to 0xf8f80000
rather than this:
L2: 512 KB already enabledmoving to 0xf8f80000
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Scott Wood [Fri, 26 Oct 2012 00:27:41 +0000 (19:27 -0500)]
powerpc/mpc85xx: move debug tlb entry after TLB is in known state
Previously, in many if not all configs we were creating overlapping TLB entries
which is illegal. This caused a crash during boot when moving p2020rdb NAND SPL
into L2 SRAM.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
--
Prabhakar, please test that debug still works.
Scott Wood [Tue, 18 Sep 2012 23:19:05 +0000 (18:19 -0500)]
serial/ns16550: wait for TEMT before initializing
TEMT is set when the transmitter is totally empty and all output has
finished.
This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
Scott Wood [Tue, 16 Oct 2012 20:43:15 +0000 (15:43 -0500)]
serial/ns16550: don't build serial_ns16550 with MIN_FUNCTIONS
CONFIG_NS16550_MIN_FUNCTIONS is used by small SPLs to gain access to basic
ns16550 output code without pulling in things not needed by the SPL.
This previously only worked with non-MULTI configs. Recently MULTI was
made mandatory, and MIN_FUNCTIONS fails like this:
drivers/serial/libserial.o: In function `calc_divisor.clone.0':
serial_ns16550.c:(.text.calc_divisor.clone.0+0x24): undefined reference to `get_bus_freq'
drivers/serial/libserial.o: In function `_serial_getc':
(.text._serial_getc+0x30): undefined reference to `NS16550_getc'
drivers/serial/libserial.o: In function `_serial_tstc':
(.text._serial_tstc+0x30): undefined reference to `NS16550_tstc'
drivers/serial/libserial.o: In function `_serial_setbrg':
(.text._serial_setbrg+0x3c): undefined reference to `NS16550_reinit'
make[1]: *** [/tmp/u-boot/spl/u-boot-spl] Error 1
make: *** [/tmp/u-boot/spl/u-boot-spl.bin] Error 2
With MIN_FUNCTIONS we don't need anything from this file, so don't build
it. The conditional needs to be in the file itself rather than the
makefile, because the config symbols are only imported to the makefiles
once, not separately for the SPL phase of the build.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tom Rini [Tue, 20 Nov 2012 17:46:30 +0000 (10:46 -0700)]
Merge branch 'master' of git://git.denx.de/u-boot-fdt
Gerald Van Baren [Tue, 20 Nov 2012 00:26:35 +0000 (19:26 -0500)]
Merge branch 'next'
Nobuhiro Iwamatsu [Thu, 15 Nov 2012 05:56:04 +0000 (14:56 +0900)]
usb: r8a6659: Fix build by missing of parenthesis
By commit
c7e3b2b5, this was chanded to support multiple controllers.
But this has missing of parenthesis. This commit fix it.
-----
r8a66597-hcd.c: In function ‘usb_lowlevel_init’:
r8a66597-hcd.c:911:52: error: expected declaration specifiers before ‘)’
token
r8a66597-hcd.c:935:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or‘__attribute__’ before ‘{’ token
r8a66597-hcd.c:939:1: error: expected ‘{’ at end of input
-----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Lucas Stach <dev@lynxeye.de>
Nobuhiro Iwamatsu [Tue, 20 Mar 2012 20:23:29 +0000 (20:23 +0000)]
usb: r8a66597: Switched from variable to only macro
Some variables are initialized with a value defined by macro.
This was changed to use the macro directly. And the variable not to
use deleted it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Ilya Yanok [Tue, 6 Nov 2012 13:48:31 +0000 (13:48 +0000)]
omap3_beagle: use new MUSB intstead of the old one
Enable using of new MUSB framework on Beagle.
NOTE! This is not just a change of backend code: top-level behavior
is also changed, we now use USB device port for USB Ethernet instead
of serial.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:30 +0000 (13:48 +0000)]
omap3_beagle: add musb-new init
Add initialization for new MUSB framework.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:29 +0000 (13:48 +0000)]
musb-new: omap2plus backend driver
Backend driver for MUSB OTG controllers found on TI OMAP2/3/4
(tested only on OMAP3 Beagle).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:28 +0000 (13:48 +0000)]
am3517_evm: switch to musb-new
Use new musb framework instead of the old one on AM3517_EVM.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:27 +0000 (13:48 +0000)]
OMAP3: am35x: add musb functions
AM35XX specific functions for integrated USB PHY/MUSB IP.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:26 +0000 (13:48 +0000)]
OMAP3: am35x_def.h: add USB defines
Add defines for MUSB IP block on AM35X SoCs.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:25 +0000 (13:48 +0000)]
musb-new: am35x backend driver
Backend driver for MUSB OTG controllers found on TI AM35x.
It seems that on AM35X interrupt status registers can be updated
_before_ core registers. As we don't use true interrupts in U-Boot
and poll interrupt status registers instead this can result in
interrupt handler being called with non-updated core registers.
This confuses the code and result in hanged transfers.
Add a small delay in am35x_interrupt as a workaround.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:24 +0000 (13:48 +0000)]
am335x_evm: enable both musb gadget and host
Enable musb gadget in Ethernet mode on port 0 and
musb host on port1.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:23 +0000 (13:48 +0000)]
am33xx: init OTG hardware and new musb gadget driver
AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:22 +0000 (13:48 +0000)]
musb-new: dsps backend driver
Backend driver for MUSB OTG controllers found on TI AM33xx and
TI81xx SoCs (tested with AM33xx only).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:21 +0000 (13:48 +0000)]
musb-new: port of Linux musb driver
Existing U-Boot musb driver has no support for the new gadget framework
and also seems to have other limitations. As gadget framework is ported
from Linux it seems pretty natural to port musb gadget driver as well.
This driver supports both host and peripheral modes.
This is not a replacement for current musb driver (at least now) as
there are still some consumers of the old UDC interface.
No DMA operation support included, CONFIG_MUSB_PIO_ONLY should be
defined.
Virtual root hub device is not implemented.
Known problems: with no devices connected usb_lowlevel_start() fails.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:20 +0000 (13:48 +0000)]
usb: use linux/usb/ch9.h instead of usbdescriptors.h
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Ilya Yanok [Tue, 6 Nov 2012 13:48:19 +0000 (13:48 +0000)]
linux/usb/ch9.h: update with the version from Linux tree
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Allen Martin [Tue, 6 Nov 2012 21:26:03 +0000 (13:26 -0800)]
USB: add arrow key support to usb_kbd
Check for scancodes for arrow keys and map them to ^F/^B, ^N/^P.
Control characters are used instead of ANSI sequence because the
queueing code in usb_kbd doesn't handle the data increase when one
keypress generates 3 keycodes. The real fix is to convert this driver
to use the input subsystem and queue, but this allows arrow keys to
work until this driver is converted.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Allen Martin [Wed, 24 Oct 2012 08:32:06 +0000 (08:32 +0000)]
tegra: Enable USB keyboard
Enable USB keyboard for seaboard and ventana
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Allen Martin [Wed, 24 Oct 2012 08:32:05 +0000 (08:32 +0000)]
tegra: move TEGRA_DEVICE_SETTINGS to tegra-common-post.h
Move environment settings for stdin/stdout/stderr to
tegra-common-post.h and generate them automaticaly based on input
device selection.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Allen Martin [Wed, 24 Oct 2012 08:32:04 +0000 (08:32 +0000)]
USB: make usb_kbd obey USB DMA alignment requirements
Change usb_kbd driver to obey alignment requirements for USB DMA on
the buffer used for data transfer. This is necessary for
architectures that enable dcache and enable USB DMA.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Jeroen Hofstee [Mon, 22 Oct 2012 20:35:46 +0000 (22:35 +0200)]
boards: remove the no longer used CONFIG_EHCI_DCACHE
CONFIG_EHCI_DCACHE was removed by commit b8adb12
"USB: Drop cache flush bloat in EHCI-HCD". Remove the defines from
the boards configs as well.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: Marek Vasut <marex@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Tom Rini <trini@ti.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Thierry Reding <thierry.reding@avionic-design.de>
cc: Tom Warren <twarren@nvidia.com>
cc: Stephen Warren <swarren@nvidia.com>
cc: Stefano Babic <sbabic@denx.de>
Tom Rini [Mon, 19 Nov 2012 16:28:04 +0000 (09:28 -0700)]
Merge branch 'master' of git://git.denx.de/u-boot-video
Tom Rini [Mon, 19 Nov 2012 16:27:18 +0000 (09:27 -0700)]
Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-staging
Robert P. J. Day [Sun, 11 Nov 2012 03:24:44 +0000 (03:24 +0000)]
cmd_mmc.c: Fix typo, "dislay" -> "display"
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Vikram Narayanan [Sat, 10 Nov 2012 02:32:46 +0000 (02:32 +0000)]
mx53loco: Fix build error when CONFIG_VIDEO is disabled
The inclusion of LCD patch into mx53loco breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video
related stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Vikram Narayanan [Sat, 10 Nov 2012 02:28:52 +0000 (02:28 +0000)]
mx51evk: Fix build error when CONFIG_VIDEO is disabled
The inclusion of LCD patch into mx51evk breaks the build when
CONFIG_VIDEO is disabled. Fix this by splitting the video related
stuff to a new file.
Also rename the function lcd_iomux to setup_iomux_lcd to make the
namings aligned with the other iomux functions.
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Andreas Bießmann [Wed, 14 Nov 2012 12:32:37 +0000 (13:32 +0100)]
fs/fs.c: do_fsload: measure throughput
This patch adds time measurement and throughput calculation for
all supported load commands.
The output of ext2load changes from
---8<---
1830666 bytes read
--->8---
to
---8<---
1830666 bytes read in 237 ms (7.4 MiB/s)
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
[agust: rebased and revised commit log]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Alejandro Mery [Wed, 31 Oct 2012 08:21:33 +0000 (08:21 +0000)]
fs: zfs: fix illegal use of fp
the upcoming sunxi (allwinner a10/a13) platform enables zfs
by default, and using linaro's hf -msoft-float makes the build
fail because this u64 division.
Signed-off-by: Alejandro Mery <amery@geeks.cl>
Acked-by: Stefan Roese <sr@denx.de>
Jens Scharsig (BuS Elektronik) [Wed, 14 Nov 2012 00:10:20 +0000 (00:10 +0000)]
Video: fix compiler warnings in bus_vcxk
if a board uses the vcxk driver option CONFIG_SYS_VCXK_DOUBLEBUFFERD,
compilier shows warnings. This patch will fix it.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Jens Scharsig (BuS Elektronik) [Tue, 30 Oct 2012 00:46:05 +0000 (00:46 +0000)]
M68K: eb_cpu5282: general update and enhanced board support
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:17 +0000 (03:22 +0000)]
arm:universal_c210:pmic: Adjust C210 Universal target platform board to new PMIC framework
Move pmic_init() function call from board_init() to power_init_board()
to work with new PMIC/POWER framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:16 +0000 (03:22 +0000)]
arm:goni:pmic: Adjust GONI target platform board to new PMIC framework
Move pmic_init() function call from board_init() to power_init_board()
to work with new PMIC/POWER framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:15 +0000 (03:22 +0000)]
power:pmic: Rename CONFIG_DIALOG_PMIC defines to CONFIG_DIALOG_POWER
Rename CONFIG_DIALOG_PMIC to CONFIG_DIALOG_POWER
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:14 +0000 (03:22 +0000)]
power:pmic: Rename CONFIG_PMIC* defines to CONFIG_POWER
Rename all CONFIG_PMIC* defines to CONFIG_POWER*
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:13 +0000 (03:22 +0000)]
power:pmic: Rename ./drivers/power/pmic_* to ./drivers/power/power_* files
Rename pmic/power related files at ./drivers/power directory
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:12 +0000 (03:22 +0000)]
pmic: Extend PMIC framework to support battery related commands
Two extra commands:
"pmic name bat state" and "pmic name bat charge" has been added to
pmic framework. Those provides state display and charge capabilities
to named batteries.
The pmic_core.c file has been refactored to more consistent name scheme.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:11 +0000 (03:22 +0000)]
arm:trats:pmic: Support for charging battery at Samsung's TRATS board
The battery connected to Samsung's Trats development board is now
charged when voltage drops below threshold.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:10 +0000 (03:22 +0000)]
arm:trats:pmic: Power consumption reduction state for Samsung's TRATS board
When charging battery is necessary, the development board needs to
be turned into low power mode for better efficiency.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:09 +0000 (03:22 +0000)]
pmic:max8997: Support for MAX8997 internal charger control
Support for MAX8997 built-in charger.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:08 +0000 (03:22 +0000)]
arm:trats:pmic: Enable battery support at Samsung's TRATS board
Support for TRATS battery has been added. It is treated as a "normal"
power related device and thereof controlled by pmic/power subsystem.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:07 +0000 (03:22 +0000)]
arm:trats:pmic: Enable fuel-gauge (MAX17042) at Samsung's TRATS board
FG IC built into the MAX8997 device (compliant to MAX17042) is enabled
at TRATS.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:06 +0000 (03:22 +0000)]
arm:trats:pmic: Enable MUIC (MAX8997) at Samsung's TRATS board
MUIC IC built into the MAX8997 device is enabled at TRATS.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:05 +0000 (03:22 +0000)]
arm:trats:pmic: Default PMIC(MAX8997) initialization for Samsung's TRATS board
Default PMIC (MAX8997) initialization for Samsung's TRATS development board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:04 +0000 (03:22 +0000)]
pmic:max8997: Function for calculating LDO internal register value
Function for calculating LDO internal register value from passed micro
Volt.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:03 +0000 (03:22 +0000)]
pmic:fuel-gauge: Support for MAX17042 fuel-gauge
Support for MAX17042 fuel-gauge (FG), which is built into the MAX8997
power management device.
Special file - fg_battery_cell_params.h with cells characteristics
added.
The FG device will work with redesigned PMIC framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:02 +0000 (03:22 +0000)]
pmic:muic: Support for MUIC built into MAX8997 device
Support for MUIC (Micro USB Integrated Circuit) built into the MAX8997
power management device.
The MUIC device will work with redesigned PMIC framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:01 +0000 (03:22 +0000)]
pmic:battery: Support for Trats Battery at PMIC framework
Trats battery is now treated in the same way as other power related
devices. This approach allows for more unified handling of all devices
responsible for power management.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:22:00 +0000 (03:22 +0000)]
pmic: Extend struct pmic to support battery and charger related operations
Now it is possible to provide specific function per PMIC/power
device instance.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:59 +0000 (03:21 +0000)]
pmic: Move pmic related code to ./drivers/power directory
The PMIC framework has been moved to its more natural place
./drivers/power from ./drivers/misc directory.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:58 +0000 (03:21 +0000)]
pmic:chrg: Common information about charger and battery (power_chrg.h)
New power_chrg.h file has been added to "bind" together common
information about charging battery available in the system.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:57 +0000 (03:21 +0000)]
pmic: Enable power_board_init() support at TRATS
Enable support for power_board_init() method at TRATS board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:56 +0000 (03:21 +0000)]
pmic: Introduce power_init_board() method at ./lib/board.c file
It is necessary to introduce a new system wide function- power_init_board()
It turns out, that power initialization must be done as early as possible.
In the case of PMIC framework redesign, which aims to support multiple
instances of PMIC devices the initialization shall be performed just
after malloc configuration.
The power_init_board function is a weak function with default implementation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:55 +0000 (03:21 +0000)]
pmic: Extend PMIC framework to support multiple instances of PMIC devices
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:54 +0000 (03:21 +0000)]
pmic:max8997: Switch the MAX8997 PMIC to be used with multibus I2C
PMIC MAX8997 is now ready to work with single and multibus soft I2C
implementation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:53 +0000 (03:21 +0000)]
pmic:i2c: Add I2C sensor byte order (big/little) to PMIC framework
Since the pmic_reg_read is the u32 value, the order in which bytes
are placed to form u32 value is important.
Support for big and little sensor endianess is added.
Moreover calls to [leXX|beXX]_to_cpu have been added to support
little and big endian SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Łukasz Majewski [Tue, 13 Nov 2012 03:21:52 +0000 (03:21 +0000)]
pmic:i2c: Handle PMIC I2C transmission comprising of two bytes
This patch adds support for proper handling of a PMIC I2C transmission
comprising of two bytes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Scott Wood [Tue, 13 Nov 2012 12:30:39 +0000 (12:30 +0000)]
nand_spl: fix u-boot.lst breakage
Commit
97b24d3d51a92cb8c0c1e1a74abf22fe1a1807a3 "common: Add symbol
handling for generic lists into Makefile" introduced build errors in many
nand_spl targets, complaining of a missing u-boot.lst. When not doing an
out-of-tree build, $(obj) expands to nothing, so GCC ended up being given
-I with no argument (or rather, -ansi was the argument). The failure
didn't show up during a -j1 build because it was picking up the non-SPL
version of u-boot.lst.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Andreas Bießmann [Tue, 13 Nov 2012 06:31:39 +0000 (06:31 +0000)]
Makefile: silence 'make clean'
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Simon Glass [Tue, 30 Oct 2012 06:15:16 +0000 (06:15 +0000)]
patman: Issue empty change logs for unchanged patches
Often a particular patch may change only for some versions of a series.
For versions where there is no change, issue a change log indicating
that (for example 'Changes in v4: None').
For such lines, don't add a blank line afterwards, to conserve space.
Use list.insert() instead of list = [item] + list.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
Simon Glass [Wed, 31 Oct 2012 14:02:42 +0000 (14:02 +0000)]
fdt: Remove fdtdec_find_alias_node() function
This function is not needed, since fdt_path_offset() performs the same
service. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Thu, 25 Oct 2012 16:31:11 +0000 (16:31 +0000)]
fdt: Set kernaddr if fdt indicates a kernel is present
If kernel-offset is specified in the fdt, set an environment variable
so that scripts can access the attached kernel.
This can be used by a packaging program to tell U-Boot about a kernel
that has been downloaded alongside U-Boot. The value in the fdt is
the offset of the kernel from the start of the U-Boot image, so we can
find it just by adding CONFIG_SYS_TEXT_BASE.
It is then fairly easy to put something like this in the environment
variables in the board header file:
"if test ${kernaddr} != \"\"; then "\
"echo \"Using bundled kernel\"; "\
"bootm ${kernaddr};" \
"fi; "\
/* rest of boot sequence follows here */
Signed-off-by: Simon Glass <sjg@chromium.org>
Gabe Black [Thu, 25 Oct 2012 16:31:10 +0000 (16:31 +0000)]
fdt: Add option to default to most compatible conf in a fit image
When booting a fit image with multiple configurations, the user either has to
specify which configuration to use explicitly, or there has to be a default
defined which is chosen automatically. This change adds an option to change
that behavior so that a configuration can be selected explicitly, or the
configuration which has the device tree that claims to be compatible with the
earliest item in U-Boot's device tree.
In other words, if U-Boot claimed to be compatible with A, B, and then C, and
the configurations claimed to be compatible with A, D and B, D and D, E, the
first configuration, A, D, would be chosen. Both the first and second
configurations match, but the first one matches a more specific entry in
U-Boot's device tree. The order in the kernel's device tree is ignored.
Signed-off-by: Gabe Black <gabeblack@google.com>
Commit-Ready: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Doug Anderson [Thu, 25 Oct 2012 16:31:09 +0000 (16:31 +0000)]
fdt: Allow device tree to specify secure booting
When secure booting is chosen:
* The u-boot shell is never invoked during boot--we just do a simple
table lookup to find the command. This means we could even remove
the shell parsing from u-boot and still be able to boot.
* The boot command can't be interruped.
* Failure doesn't cause us to fall back to the shell.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Gabe Black [Thu, 25 Oct 2012 16:31:08 +0000 (16:31 +0000)]
fdt: Tell the FDT library where the device tree is
This change adds a call to set_working_fdt_addr near the end of u-boot
initialization which tells the fdt command/library where the device tree is.
This makes it possible to use the fdt command to look at the active device tree
since otherwise there would be no way to know what address it was at to set
things up manually.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Che-Liang Chiou [Thu, 25 Oct 2012 16:31:07 +0000 (16:31 +0000)]
fdt: Load boot command from device tree
Load boot command from /config/bootcmd of device tree if present.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Sean Paul [Thu, 25 Oct 2012 16:31:06 +0000 (16:31 +0000)]
fdt: Add polarity-aware gpio functions to fdtdec
Add get and set gpio functions to fdtdec that take into account the
polarity field in fdtdec_gpio_state.flags.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Che-Liang Chiou [Thu, 25 Oct 2012 16:31:05 +0000 (16:31 +0000)]
fdt: Add fdtdec_get_uint64 to decode a 64-bit value from a property
It decodes a 64-bit value from a property that is at least 8 bytes long.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>